|
Compaq Mini User Guide
Safety warning notice
WARNING! To reduce the possibility of heat-related injuries or of overheating the computer, do not
place the computer directly on your lap or obstruct the computer air vents. Use the computer only on a
hard, flat surface. Do not allow another hard surface, such as an adjoining optional printer, or a soft
surface, such as pillows or rugs or clothing, to block airflow. Also, do not allow the AC adapter to contact
the skin or a soft surface, such as pillows or rugs or clothing, during operation. The computer and the
AC adapter comply with the user-accessible surface temperature limits defined by the International
Standard for Safety of Information Technology Equipment (IEC 60950).
iii
iv
Safety warning notice
Table of contents
2 Power management
Connecting the AC adapter ............................................................................................... 14
Using battery power ........................................................................................................................... 14
Displaying the remaining battery charge ........................................................................... 15
Maximizing battery discharge time .................................................................................... 17
Managing low battery levels .............................................................................................. 17
v
Resolving a low battery level when a charged battery is
Resolving a low battery level when no power source is
Resolving a low battery level when the computer cannot exit
Step 5: Reenable Hibernation and Sleep .......................................................... 20
3 Internet
Identifying wireless and network status icons ................................................... 25
4 Multimedia
vi
5 Security
6 Digital cards
7 USB devices
8 Pointing devices and keyboard
Switching the screen ........................................................................................ 57
vii
Initiating QuickLock .......................................................................................... 57
9 Drives
10 Memory modules
11 Updating software
12 Setup Utility
viii
1 Knowing the parts
Identifying the hardware
Components included with the computer may vary by region and model. The illustrations in this chapter
identify the standard features on most computer models.
To see a list of hardware installed in the computer:
Select Start > Control Panel > System and Security. In the System area click Device
▲
Manager.
You can also add hardware or modify computer configurations using Device Manager.
Top components
TouchPad
Component
Description
(1)
(2)
Left TouchPad button*
TouchPad*
Functions like the left button on an external mouse.
Moves the pointer and selects or activates items on the
screen.
(3)
TouchPad scroll zone
Scrolls up or down.
Identifying the hardware
1
(4)
Right TouchPad button*
Functions like the right button on an external mouse.
*This table describes factory settings. To view or change pointing device preferences, select Start > Devices and Printers.
Then, right-click the device representing your computer, and select Mouse settings.
Light
Component
Description
Caps lock light
On: Caps lock is on.
2
Chapter 1 Knowing the parts
Keys
Component
(1)
Description
Function keys
fn key
Execute frequently used system functions when
pressed in combination with the fn key.
(2)
Executes frequently used system functions when
pressed in combination with a function key.
(3)
(4)
Windows® logo key
Displays the Windows Start menu.
Windows applications key
Displays a shortcut menu for items beneath the
pointer.
Front components
Identifying the hardware
3
Component
(1)
Description
Power light
On: The computer is on.
●
●
●
●
Blinking: The computer is in Sleep.
Off: The computer is off or in Hibernation.
(2)
Power switch
When the computer is off, slide the switch to turn
on the computer.
When the computer is on, briefly slide the switch
to initiate Hibernation.
●
●
●
When the computer is in Sleep, briefly slide the
switch to exit Sleep.
When the computer is in Hibernation, briefly
slide the switch to exit Hibernation.
If the computer has stopped responding and
Windows shutdown procedures are ineffective, slide
and hold the power switch for at least 5 seconds to
turn off the computer.
To learn more about your power settings, select
Start > Control Panel > System and Security >
Power Options.
(3)
(4)
Drive light
Blinking: The hard drive or flash drive is being
accessed.
Battery light
On: A battery is charging.
●
●
Blinking: A battery that is the only available
power source has reached a low battery level.
When the battery reaches a critical battery level,
the battery light begins blinking rapidly.
Off: If the computer is plugged into an external
power source, the light turns off when all
batteries in the computer are fully charged. If the
computer is not plugged into an external power
source, the light stays off until the battery
reaches a low battery level.
●
(5)
(6)
Wireless light
Blue: An integrated wireless device, such as a
wireless local area network (WLAN) device and/
or a Bluetooth® device, is on.
●
●
Amber: All wireless devices are off.
Wireless switch
Turns the wireless feature on or off, but does not
establish a wireless connection.
NOTE: A wireless network must be set up in order
to establish a wireless connection.
4
Chapter 1 Knowing the parts
Right-side components
Component
Description
(1)
(2)
USB ports (2)
Connect optional USB devices.
Digital Media Slot
Supports the following optional digital card formats:
Memory Stick (MS)
MS/Pro
●
●
●
●
●
MultiMediaCard (MMC)
Secure Digital (SD) Memory Card
xD-Picture card
(3)
(4)
External monitor port
RJ-45 (network) jack
Connects an optional external display, such as a
monitor or projector, to the computer.
Connects a network cable.
Left-side components
Component
Description
(1)
Security cable slot
Attaches an optional security cable to the computer.
NOTE: The security cable is designed to act as a
deterrent, but it may not prevent the computer from
being mishandled or stolen.
Identifying the hardware
5
Component
(2)
Description
Power connector
AC adapter light
Connects an AC adapter.
(3)
On: The computer is connected to external
power.
●
●
Off: The computer is not connected to external
power.
(4)
Vent
Enables airflow to cool internal components.
NOTE: The computer fan starts up automatically to
cool internal components and prevent overheating. It
is normal for the internal fan to cycle on and off during
routine operation.
(5)
(6)
USB port
Connects an optional USB device.
Audio-out (headphone) jack/Audio-in (microphone)
jack
Produces sound when connected to optional powered
stereo speakers, headphones, earbuds, a headset, or
television audio. Also connects an optional headset
microphone.
WARNING! To reduce the risk of personal injury,
adjust the volume before putting on headphones,
earbuds, or a headset. For additional safety
information, refer to the Regulatory, Safety and
Environmental Notices.
NOTE: When an audio component is connected to
the jack, the computer speakers are disabled.
The audio component cable must have a 4-conductor
connector.
Display components
6
Chapter 1 Knowing the parts
Component
Description
(1)
(2)
Speakers (2)
Internal display switch
Produce sound.
Turns off the display if the display is closed while the
power is on.
NOTE: The display switch is not visible from the
outside of the computer.
(3)
Webcam
Captures still photographs and videos.
NOTE: To capture videos, you must install additional
webcam software.
(4)
(5)
Webcam light
On: The webcam is in use.
Records sound.
Internal microphone
Bottom components
Component
Description
(1)
(2)
Battery bay
Holds the battery.
Battery release latches (2)
Release the battery from the battery bay.
(3)
Vent
Enables airflow to cool internal components.
Identifying the hardware
7
Component
Description
NOTE: The computer fan starts up automatically to cool
internal components and prevent overheating. It is normal
for the internal fan to cycle on and off during routine
operation.
(4)
Memory module compartment
Contains the memory module slot.
Wireless antennas
Component
Description
(1)
(2)
WWAN antennas (2) (select models only)*
Send and receive wireless signals to communicate with wireless
wide-area networks (WWANs).
WLAN antennas (2)*
Send and receive wireless signals to communicate with wireless
local area networks (WLANs).
*The antennas are not visible from the outside of the computer. For optimal transmission, keep the areas immediately around
the antennas free from obstructions.
To see wireless regulatory notices, refer to the section of the Regulatory, Safety and Environmental
Notices that applies to your country or region. To access these notices, select Start > Help and
Support > User Guides.
8
Chapter 1 Knowing the parts
Additional hardware components
Component
Description
(1)
(2)
(3)
Power cord*
AC adapter
Battery*
Connects an AC adapter to an AC outlet.
Converts AC power to DC power.
Powers the computer when it is not plugged into external power.
*Batteries and power cords vary in appearance by region and country.
Identifying the labels
The labels affixed to the computer provide information you may need when you troubleshoot system
problems or travel internationally with the computer.
Service tag—Provides important information including the following:
●
Product name (1). This is the product name affixed to the front of your computer.
◦
◦
◦
Serial number (s/n) (2). This is an alphanumeric identifier that is unique to each product.
Part Number/Product number (p/n) (3). This number provides specific information about the
hardware components of the product. The part number helps a service technician to determine
what components and parts are needed.
Model description (4). This is the alphanumeric identifier you use to locate documents, drivers,
and support for your computer.
◦
◦
Warranty period (5). This number describes the duration (in years) of the warranty period for
this computer.
Identifying the labels
9
Have this information available when you contact technical support. The service tag label is affixed
to the bottom of the computer.
Microsoft® Certificate of Authenticity—Contains the Windows® Product Key. You may need the
Product Key to update or troubleshoot the operating system. This certificate is affixed to the bottom
of the computer.
●
●
Regulatory label—Provides regulatory information about the computer, including the following:
Information about optional wireless devices and the approval markings of some of the
countries or regions in which the devices have been approved for use. An optional device may
be a wireless local area network (WLAN) device. You may need this information when
traveling internationally.
◦
The serial number of your HP Mobile Broadband Module (select models only).
◦
The regulatory label is affixed to the bottom of the computer.
10 Chapter 1 Knowing the parts
2 Power management
Setting power options
Using power-saving states
The computer has two power-saving states enabled at the factory: Sleep and Hibernation.
When Sleep is initiated, the power light blinks and the screen clears. Your work is saved to memory.
Exiting Sleep is faster than exiting Hibernation. If the computer is in Sleep for an extended period or if
the battery reaches a critical battery level while in Sleep, the computer initiates Hibernation.
When Hibernation is initiated, your work is saved to a hibernation file on the hard drive and the computer
turns off.
CAUTION: To prevent possible audio and video degradation, loss of audio or video playback
functionality, or loss of information, do not initiate Sleep or Hibernation while reading from or writing to
a disc or an external media card.
NOTE: You cannot initiate any type of networking connection or perform any computer functions while
the computer is in Sleep or in Hibernation.
Initiating and exiting Sleep
The system is set at the factory to initiate Sleep after 15 minutes of inactivity when running on battery
power and 30 minutes of inactivity when running on external power.
Power settings and timeouts can be changed using Power Options in Windows Control Panel.
With the computer on, you can initiate Sleep in any of the following ways:
Press fn+f1.
●
●
Click Start, click the arrow next to the Shut down button, and then click Sleep.
To exit Sleep:
Briefly slide the power switch.
▲
When the computer exits Sleep, the power light turns on and your work returns to the screen where
you stopped working.
NOTE: If you have set a password to be required when the computer exits Sleep, you must enter your
Windows password before your work will return to the screen.
Setting power options 11
Initiating and exiting Hibernation
The system is set at the factory to initiate Hibernation after 1,080 minutes of inactivity when running on
battery power or when the battery reaches a critical battery level.
NOTE: The system will not initiate Hibernation when running on external power.
NOTE: To reduce the risk of information loss, periodically save your work.
Power settings and timeouts can be changed using Power Options in Windows Control Panel.
To initiate Hibernation:
Click Start, click the arrow next to the Shut down button, and then click Hibernate.
▲
To exit Hibernation:
Briefly slide the power switch.
▲
When the computer exits Hibernation, the power light turns on and your work returns to the screen where
you stopped working.
NOTE: If you have set a password to be required when the computer exits Hibernation, you must enter
your Windows password before your work will return to the screen.
Using power plans
A power plan is a collection of system settings that manages how the computer uses power. Power
plans can help you conserve power and maximize computer performance.
The following power plans are available:
Portable/Laptop (recommended)
Home/Office Desk
Presentation
●
●
●
●
●
●
Always On
Minimal Power Management
Max Battery
You can change the settings of these power plans through Power Options.
Viewing the current power plan
Click the Battery Meter icon in the notification area, at the far right of the taskbar.
– or –
▲
Select Start > Control Panel > System and Security > Power Options.
Selecting a different power plan
Click the Battery Meter icon in the notification area, and then select a power plan from the list.
– or –
▲
12 Chapter 2 Power management
Select Start > Control Panel > System and Security > Power Options, and then select a power
plan from the list.
Customizing a power plan
1. Click the Battery Meter icon in the notification area, and then click More power options.
– or –
Select Start > Control Panel > System and Security > Power Options.
2. Select a power plan, and then click Change plan settings.
3. Change the settings as needed.
4. To change additional settings, click Change advanced power settings and make your changes.
Setting password protection upon wakeup
To set the computer to prompt for a password when the computer exits Sleep or Hibernation, follow
these steps:
1. Select Start > Control Panel > System and Security > Power Options.
2. In the left pane, click Require a password on wakeup.
3. Click Change Settings that are currently unavailable.
4. Click Require a password (recommended).
5. Click Save changes.
Using external AC power
External AC power is supplied through one of the following devices:
WARNING! To reduce potential safety issues, use only the AC adapter provided with the computer,
a replacement AC adapter provided by HP, or a compatible AC adapter purchased from HP.
Approved AC adapter
●
●
Optional docking device or optional expansion product
Connect the computer to external AC power under any of the following conditions:
WARNING! Do not charge the computer battery while you are onboard aircraft.
When you are charging or calibrating a battery
When you are installing or modifying system software
When you are writing information to a CD or DVD
●
●
●
When you connect the computer to external AC power, the following events occur:
The battery begins to charge.
●
●
If the computer is turned on, the battery meter icon in the notification area changes appearance.
Using external AC power 13
When you disconnect external AC power, the following events occur:
The computer switches to battery power.
●
●
The display brightness is automatically decreased to save battery life. To increase display
brightness, press the fn+f4 hotkey or reconnect the AC adapter.
Connecting the AC adapter
WARNING! To reduce the risk of electric shock or damage to the equipment:
Plug the power cord into an AC outlet that is easily accessible at all times.
Disconnect power from the computer by unplugging the power cord from the AC outlet (not by
unplugging the power cord from the computer).
If provided with a 3-pin attachment plug on the power cord, plug the cord into a grounded (earthed) 3-
pin outlet. Do not disable the power cord grounding pin, for example, by attaching a 2-pin adapter. The
grounding pin is an important safety feature.
To connect the computer to external AC power, follow these steps:
1. Plug the AC adapter into the power connector (1) on the computer.
2. Plug the power cord into the AC adapter (2).
3. Plug the other end of the power cord into an AC outlet (3).
Using battery power
When a charged battery is in the computer and the computer is not plugged into external power, the
computer runs on battery power. When the computer is plugged into external AC power, the computer
runs on AC power.
If the computer contains a charged battery and is running on external AC power supplied through the
AC adapter, the computer switches to battery power if the AC adapter is disconnected from the
computer.
NOTE: The display brightness is decreased to save battery life when you disconnect AC power. To
increase display brightness, use the fn+f4 hotkey or reconnect the AC adapter.
14 Chapter 2 Power management
You can keep a battery in the computer or in storage, depending on how you work. Keeping the battery
in the computer whenever the computer is plugged into AC power charges the battery and also protects
your work in case of a power outage. However, a battery in the computer slowly discharges when the
computer is off and unplugged from external power.
WARNING! To reduce potential safety issues, use only the battery provided with the computer, a
replacement battery provided by HP, or a compatible battery purchased from HP.
Computer battery life varies, depending on power management settings, programs running on the
computer, display brightness, external devices connected to the computer, and other factors.
Displaying the remaining battery charge
Move the pointer over the Battery Meter icon in the notification area, at the far right of the taskbar.
▲
Inserting or removing the battery
CAUTION: Removing a battery that is the sole power source may cause loss of information. To prevent
loss of information, save your work and initiate Hibernation or shut down the computer through Windows
before removing the battery.
To insert the battery:
1. Turn the computer upside down on a flat surface.
2. Align the tabs on the battery with the notches on the computer, and then insert the battery into the
battery bay. The battery release latches automatically lock the battery into place.
To remove the battery:
1. Turn the computer upside down on a flat surface.
Using battery power 15
2. Slide the battery release latches (1) to release the battery, and then remove the battery (2).
Charging a battery
WARNING! Do not charge the computer battery while you are onboard aircraft.
The battery charges whenever the computer is plugged into external power through an AC adapter, an
optional power adapter, an optional docking device, or an optional expansion product.
The battery charges whether the computer is off or in use, but it charges faster when the computer is
off.
Charging may take longer if a battery is new, has been unused for 2 weeks or more, or is much warmer
or cooler than room temperature.
To prolong battery life and optimize the accuracy of battery charge displays, follow these
recommendations:
If you are charging a new battery, charge it fully before turning on the computer.
Charge the battery until the battery light turns off.
●
●
NOTE: If the computer is on while the battery is charging, the battery meter in the notification
area may show 100 percent charge before the battery is fully charged.
Allow the battery to discharge below 5 percent of a full charge through normal use before charging
it.
●
●
If the battery has been unused for one month or more, calibrate the battery instead of simply
charging it.
The battery light displays charge status:
On: The battery is charging.
●
●
Blinking: The battery that is the only available power source has reached a low battery level. When
the battery reaches a critical battery level, the battery light begins blinking rapidly.
Off: The battery is fully charged, in use, or not installed.
●
16 Chapter 2 Power management
Maximizing battery discharge time
Battery discharge time varies depending on the features you use while on battery power. Maximum
discharge time gradually shortens, as the battery storage capacity naturally degrades.
Tips for maximizing battery discharge time:
Decrease the brightness on the display.
●
●
●
●
Check the Power saver setting in Power options.
Remove the battery from the computer when it is not being used or charged.
Store the battery in a cool, dry location.
Managing low battery levels
The information in this section describes the alerts and system responses set at the factory. Some low-
battery alerts and system responses can be changed using Power Options in Windows Control Panel.
Preferences set using Power Options do not affect lights.
Identifying low battery levels
When a battery that is the sole power source for the computer reaches a low battery level, the battery
light blinks.
If a low battery level is not resolved, the computer enters a critical battery level, and the battery light
blinks rapidly.
The computer takes the following actions for a critical battery level:
If Hibernation is enabled and the computer is on or in Sleep, the computer initiates Hibernation.
●
●
If Hibernation is disabled and the computer is on or in Sleep, the computer remains briefly in Sleep,
and then shuts down and loses any unsaved information.
Using battery power 17
Resolving a low battery level
CAUTION: To reduce the risk of losing information when the computer reaches a critical battery level
and has initiated Hibernation, do not restore power until the power light turns off.
Resolving a low battery level when external power is available
Connect one of the following devices:
▲
AC adapter
●
●
●
Optional expansion product or docking device
Optional power adapter
Resolving a low battery level when a charged battery is available
1. Turn off the computer or initiate Hibernation.
2. Remove the discharged battery, and then insert a charged battery.
3. Turn on the computer.
Resolving a low battery level when no power source is available
Initiate Hibernation.
▲
– or –
Save your work and shut down the computer.
Resolving a low battery level when the computer cannot exit Hibernation
When the computer lacks sufficient power to exit Hibernation, follow these steps:
1. Insert a charged battery or plug the computer into external power.
2. Exit Hibernation by briefly sliding the power switch.
Calibrating a battery
Calibrate a battery under the following conditions:
When battery charge displays seem inaccurate
●
●
When you observe a significant change in battery run time
Even if a battery is heavily used, it should not need to be calibrated more than once a month. It is also
not necessary to calibrate a new battery.
Step 1: Fully charge the battery
WARNING! Do not charge the computer battery while you are onboard aircraft.
NOTE: The battery charges whether the computer is off or in use, but it charges faster when the
computer is off.
18 Chapter 2 Power management
To fully charge the battery:
1. Insert the battery into the computer.
2. Connect the computer to an AC adapter, optional power adapter, optional expansion product, or
optional docking device, and then plug the adapter or device into external power.
The battery light on the computer turns on.
3. Leave the computer plugged into external power until the battery is fully charged.
The battery light on the computer turns off.
Step 2: Disable Hibernation and Sleep
1. Click the Battery meter icon in the notification area, and then click More Power options.
– or –
Select Start > Control Panel > System and Security > Power Options.
2. Under the current power plan, click Change plan setting.
3. Record the Turn off the display settings listed in the On battery column so that you can reset
them after the calibration.
4. Change the Turn off the display settings to Never.
5. Click Change advanced power settings.
6. Click the plus sign next to Sleep, and then click the plus sign next to Hibernate after.
7. Record the On battery setting under Hibernate after so that you can reset it after the calibration.
8. Change the On battery setting to Never.
9. Click OK.
10. Click Save changes.
Step 3: Discharge the battery
The computer must remain on while the battery is being discharged. The battery can discharge whether
or not you are using the computer, but the battery will discharge faster while you are using it.
If you plan to leave the computer unattended during the discharge, save your information before
beginning the discharge procedure.
●
If you use the computer occasionally during the discharge procedure and have set energy-saving
timeouts, expect the following performance from the system during the discharge process:
●
The monitor will not turn off automatically.
◦
◦
◦
Hard drive speed will not decrease automatically when the computer is idle.
System-initiated Hibernation will not occur.
Using battery power 19
To discharge a battery:
1. Unplug the computer from its external power source, but do not turn off the computer.
2. Run the computer on battery power until the battery is discharged. The battery light begins to blink
when the battery has discharged to a low battery level. When the battery is discharged, the battery
light turns off and the computer shuts down.
Step 4: Fully recharge the battery
To recharge the battery:
1. Plug the computer into external power and maintain external power until the battery is fully
recharged. When the battery is recharged, the battery light on the computer turns off.
You can use the computer while the battery is recharging, but the battery will charge faster if the
computer is off.
2. If the computer is off, turn it on when the battery is fully charged and the battery light has turned
off.
Step 5: Reenable Hibernation and Sleep
CAUTION: Failure to reenable Hibernation after calibration may result in a full battery discharge and
information loss if the computer reaches a critical battery level.
1. Click the Battery meter icon in the notification area, and then click More Power options.
– or –
Select Start > Control Panel > System and Security > Power Options.
2. Under the current power plan, click Change plan settings.
3. Reenter the settings that you recorded for the items in the On battery column.
4. Click Change advanced power settings.
5. Click the plus sign next to Sleep, and then click the plus sign next to Hibernate after.
6. Reenter the setting that you recorded for On battery.
7. Click OK.
8. Click Save changes.
Conserving battery power
Select the Power saver power plan through Power Options under System and Security in
Windows Control Panel.
●
●
●
●
Turn off wireless and local area network (LAN) connections and exit modem software when you
are not using them.
Disconnect external devices that are not plugged into an external power source, when you are not
using them.
Stop, disable, or remove any external media cards that you are not using.
20 Chapter 2 Power management
Use the fn+f3 and fn+f4 hotkeys to adjust screen brightness as needed.
●
●
If you leave your work, initiate Sleep or Hibernation, or shut down the computer.
Storing a battery
CAUTION: To prevent damage to a battery, do not expose it to high temperatures for extended periods
of time.
If a computer will be unused and unplugged from external power for more than 2 weeks, remove the
battery and store it separately.
To prolong the charge of a stored battery, place it in a cool, dry place.
NOTE: A stored battery should be checked every 6 months. If the capacity is less than 50 percent,
recharge the battery before returning it to storage.
Calibrate a battery before using it if it has been stored for one month or more.
Disposing of a used battery
WARNING! To reduce the risk of fire or burns, do not disassemble, crush, or puncture; do not short
external contacts; do not dispose of in fire or water.
Refer to the Regulatory, Safety and Environmental Notices for battery disposal information.
Shutting down the computer
CAUTION: Unsaved information will be lost when the computer is shut down.
The Shut Down command closes all open programs, including the operating system, and then turns off
the display and computer.
Shut down the computer under any of the following conditions:
When you need to replace the battery or access components inside the computer
●
●
●
When you are connecting an external hardware device that does not connect to a USB port
When the computer will be unused and disconnected from external power for an extended period
To shut down the computer, follow these steps:
NOTE: If the computer is in Sleep or in Hibernation, you must first exit Sleep or Hibernation before
shutdown is possible.
1. Save your work and close all open programs.
2. Click Start.
3. Click Shut down.
Shutting down the computer 21
If the computer is unresponsive and you are unable to use the preceding shutdown procedures, try the
following emergency procedures in the sequence provided:
Press ctrl+alt+delete, and then click Shut down.
●
●
●
Slide and hold the power switch for at least 5 seconds.
Disconnect the computer from external power and remove the battery.
22 Chapter 2 Power management
3 Internet
Your computer supports the following types of Internet access:
Wired—You can access the Internet by connecting to a broadband network using the RJ-45
(network) jack.
●
Wireless—For mobile Internet access, you can use a wireless connection. To learn about setting
up a wireless network or adding your computer to an existing network, refer to the “Connecting to
a wireless network” section.
●
23
Connecting to a wired network
Connecting to a local area network (LAN) requires an 8-pin, RJ-45 network cable (purchased
separately). If the network cable contains noise suppression circuitry (1), which prevents interference
from TV and radio reception, orient the circuitry end of the cable (2) toward the computer.
To connect the network cable:
WARNING! To reduce the risk of electric shock, fire, or damage to the equipment, do not plug a modem
cable or telephone cable into an RJ-45 (network) jack.
1. Plug the network cable into the network jack (1) on the computer.
2. Plug the other end of the cable into a network wall jack (2).
24 Chapter 3 Internet
Connecting to a wireless network
Using wireless devices
Wireless technology transfers data across radio waves instead of wires. Your computer may be
equipped with one or more of the following wireless devices:
Wireless local area network (WLAN) device—Connects the computer to wireless local area
networks (commonly referred to as Wi-Fi networks, wireless LANs, or WLANs) in corporate offices,
your home, and public places such as airports, restaurants, coffee shops, hotels, and universities.
In a WLAN, each mobile wireless device communicates with a wireless router or a wireless access
point.
●
●
●
HP Mobile Broadband Module (select models only)—A wireless wide area network (WWAN) device
that provides access to information wherever mobile network operator service is available. In a
WWAN, each mobile device communicates to a mobile network operator’s base station. Mobile
network operators install networks of base stations (similar to cell phone towers) throughout large
geographic areas, effectively providing coverage across entire states, regions, or even countries.
Bluetooth® device—Creates a personal area network (PAN) to connect to other Bluetooth-enabled
devices such as computers, phones, printers, headsets, speakers, and cameras. In a PAN, each
device communicates directly with other devices, and devices must be relatively close together—
typically within 10 meters (approximately 33 feet) of each other.
The device supports the following IEEE industry standards:
802.11b, the first popular standard, supports data rates of up to 11 Mbps and operates at a
frequency of 2.4 GHz.
●
802.11g supports data rates of up to 54 Mbps and operates at a frequency of 2.4 GHz. An 802.11g
WLAN device is backward compatible with 802.11b devices, so they can operate on the same
network.
●
For more information on wireless technology, refer to the information and Web site links provided in
Help and Support.
Identifying wireless and network status icons
Icon
Name
Description
Wireless (connected)
Identifies the location of the wireless light and the wireless switch
on the computer. Also identifies that one or more of the wireless
devices are on.
Wireless (disconnected)
Indicates that all of the wireless devices are off.
Wireless network connection (connected)
Wireless network connection (disconnected)
Indicates that one or more of your WLAN devices are connected
to the network.
Indicates that one or more of your WLAN devices are not
connected to a network.
Connecting to a wireless network 25
Network status (connected)
Indicates that one or more of your LAN drivers are installed and
one or more LAN devices are connected to the network.
Network status (disconnected)
Indicates that one or more of your LAN drivers are installed but
no LAN devices are connected to the network.
Using the wireless controls
You can control the wireless devices in your computer using these features:
Wireless switch
●
●
Operating system controls
Using the wireless switch
The computer has a wireless switch, one or more wireless devices, and one wireless light. All of the
wireless devices on your computer are enabled at the factory, so the wireless light is on (blue) when
you turn on the computer.
The wireless light indicates the overall power state of your wireless devices, not the status of individual
devices. If the wireless light is blue, at least one wireless device is on. If the wireless light is amber, all
wireless devices are off.
Because the wireless devices are enabled at the factory, you can use the wireless switch to turn on or
turn off all of the wireless devices simultaneously.
Using HP Connection Manager software (select models only)
You can use HP Connection Manager to connect to WWANs using the HP Mobile Broadband device in
your computer (select models only).
To start Connection Manager, click the Connection Manager icon in the notification area, at the
▲
far right of the taskbar.
– or –
Select Start > All Programs > HP Connection Manager > HP Connection Manager.
For more details about using Connection Manager, refer to the Connection Manager Help.
Using HP Wireless Assistant software
A wireless device can be turned on or off using the Wireless Assistant software. If a wireless device is
disabled by Setup Utility, it must be reenabled by Setup Utility before it can be turned on or off using
Wireless Assistant.
NOTE: Enabling or turning on a wireless device does not automatically connect the computer to a
network or a Bluetooth enabled device.
26 Chapter 3 Internet
To view the state of the wireless devices, click the Show hidden icons icon, the arrow at the left of the
notification area, and position the mouse pointer over the wireless icon.
If the wireless icon is not displayed in the notification area, complete the following steps to change
Wireless Assistant properties:
1. Select Start > Control Panel > Hardware and Sound > Windows Mobility Center.
2. Click the wireless icon in the Wireless Assistant tile, which is located in the bottom row of Windows®
Mobility Center.
3. Click Properties.
4. Select the check box next to HP Wireless Assistant icon in notification area.
5. Click Apply.
6. Click Close.
For more information, refer to the Wireless Assistant software Help:
1. Open Wireless Assistant by clicking the wireless icon in Windows Mobility Center.
2. Click the Help button.
You can use the properties dialog box in Wireless Assistant to show the on/off controls for each installed
wireless device and control the devices separately. To show the on/off controls:
1. Double-click the Wireless Assistant icon in the notification area, at the far right of the taskbar.
2. Click Properties.
3. Select the Independent controls for installed wireless devices check box, and then click
Apply.
4. Click Turn off or Turn on to control each wireless device separately.
Using a WLAN
With a WLAN device, you can access a wireless local area network (WLAN), which is composed of other
devices and accessories that are linked by a wireless router or a wireless access point.
NOTE: The terms wireless router and wireless access point are often used interchangeably.
A large-scale WLAN, such as a corporate or public WLAN, typically uses wireless access points
that can accommodate a large number of devices and accessories and can separate critical
network functions.
●
A home or small office WLAN typically uses a wireless router, which allows several wireless and
wired devices to share an Internet connection, a printer, and files without requiring additional pieces
of hardware or software.
●
To use the WLAN device in your computer, you must connect to a WLAN infrastructure (provided through
a service provider or a public or corporate network).
Connecting to a wireless network 27
Setting up a WLAN
To set up a WLAN and connect to the Internet, you need the following equipment:
A broadband modem (either DSL or cable) (1) and high-speed Internet service purchased from an
●
Internet service provider (ISP)
A wireless router (purchased separately) (2)
●
●
The wireless device (3)
The illustration below shows an example of a wireless network installation that is connected to the
Internet.
As your network grows, additional wireless and wired devices can be connected to the network to access
the Internet.
For help in setting up your WLAN, refer to the information provided by your router manufacturer or your
ISP.
Protecting your WLAN
It is essential to understand that because the WLAN standard was designed with only limited security
capabilities—basically to foil casual eavesdropping rather than more powerful forms of attack—WLANs
are vulnerable to well-known and well-documented security weaknesses.
WLANs in public areas, or “hotspots,” like coffee shops and airports may not provide any security. New
technologies are being developed by wireless manufacturers and hotspot service providers that make
the public environment more secure and anonymous. If you are concerned about the security of your
computer in a hotspot, limit your network activities to noncritical e-mail and basic Internet surfing.
When you set up a WLAN or access an existing WLAN, always enable security features to protect your
network from unauthorized access. The common security levels are Wi-Fi Protected Access (WPA)-
Personal and Wired Equivalent Privacy (WEP). Because wireless radio signals travel outside the
network, other WLAN devices can pick up unprotected signals and either connect to your network
(uninvited) or capture information being sent across it. However, you can take precautions to protect
your WLAN:
Use a wireless transmitter with built-in security
●
Many wireless base stations, gateways, or routers provide built-in security features such as
wireless security protocols and firewalls. With the correct wireless transmitter, you can protect your
network from the most common wireless security risks.
Work behind a firewall
●
A firewall is a barrier that checks both data and requests for data that are sent to your network,
and discards any suspicious items. Firewalls are available in many varieties, both software and
hardware. Some networks use a combination of both types.
28 Chapter 3 Internet
Use wireless encryption
●
A variety of sophisticated encryption protocols is available for your WLAN. Find the solution that
works best for your network security:
Wired Equivalent Privacy (WEP) is a wireless security protocol that encodes or encrypts all
network data before it is transmitted using a WEP key. Usually, you can allow the network to
assign the WEP key. Alternatively, you can set up your own key, generate a different key, or
choose other advanced options. Without the correct key, others will not be able to use the
WLAN.
◦
WPA (Wi-Fi Protected Access), like WEP, uses security settings to encrypt and decrypt data
that is transmitted over the network. However, instead of using one static security key for
encryptions as WEP does, WPA uses “temporal key integrity protocol” (TKIP) to dynamically
generate a new key for every packet. It also generates different sets of keys for each computer
on the network.
◦
Close your network
●
If possible, prevent your network name (SSID) from being broadcast by the wireless transmitter.
Most networks initially broadcast the name, telling any computer nearby that your network is
available. By closing the network, other devices are less likely to know that your network exists.
NOTE: If your network is closed and the SSID is not broadcast, you must know or remember the
SSID to connect new devices to the network. Write down the SSID and store it in a secure place
before closing the network.
Connecting to a WLAN
To connect to the WLAN, follow these steps:
1. Be sure that the WLAN device is on. If it is on, the wireless light is blue. If the wireless light is amber,
slide the wireless switch.
2. Click the network icon in the notification area, at the far right of the taskbar.
3. Select your WLAN from the list.
4. Click Connect.
If the network is a security-enabled WLAN, you are prompted to enter a network security key, which
is a security code. Type the code, and then click OK to complete the connection.
NOTE: If no WLANs are listed, you are out of range of a wireless router or access point.
NOTE: If you do not see the network you want to connect to, click Network and Sharing
Center, and then click Set up a new connection or network.
5. After the connection is made, place the mouse pointer over the wireless network connection icon
in the notification area, at the far right of the taskbar, to verify the name, speed, strength, and status
of the connection.
NOTE: The functional range (how far your wireless signals travel) depends on WLAN implementation,
router manufacturer, and interference from other electronic devices or structural barriers such as walls
and floors.
Connecting to a wireless network 29
More information about using a WLAN is available through the following resources:
Information from your ISP and the manufacturer's instructions included with your wireless router
and other WLAN equipment
●
Information and Web site links provided in Help and Support
●
For a list of public WLANs near you, contact your ISP or search the Web. Web sites that list public
WLANs include Cisco Internet Mobile Office Wireless Locations, Hotspotlist, and Geektools. Check with
each public WLAN location for cost and connection requirements.
Roaming to another network
When you move your computer within range of another WLAN, Windows attempts to connect to that
network. If the attempt is successful, your computer is automatically connected to the new network. If
Windows does not recognize the new network, follow the same procedure you used initially to connect
to your WLAN.
30 Chapter 3 Internet
Using HP Mobile Broadband (select models only)
An HP Mobile Broadband Module is a wireless wide area network (WWAN) device that provides access
to information wherever mobile network operator service is available. Using HP Mobile Broadband
requires a network service provider (called a mobile network operator), which in most cases is a mobile
phone network operator. Coverage for HP Mobile Broadband is similar to mobile phone voice coverage.
When used with mobile network operator service, HP Mobile Broadband gives you the freedom to stay
connected to the Internet, send e-mail, or connect to your corporate network whether you are on the
road or outside the range of Wi-Fi hotspots.
HP Mobile Broadband supports the following technologies:
HSPA (High Speed Packet Access) module, which provides access to networks based on the
Global System for Mobile Communications (GSM) telecommunications standard.
●
For HSPA service activation, you may need the HP Mobile Broadband Module International Mobile
Equipment Identity (IMEI) number to activate mobile broadband service. The IMEI number is printed on
a label inside the battery bay of your computer. HSPA mobile network operators require the use of a
subscriber identity module (SIM). A SIM contains basic information about you, such as a personal
identification number (PIN), as well as network information. Some computers include a SIM that is
preinstalled in the battery bay. If the SIM is not preinstalled, it may be provided in the packet of HP
Mobile Broadband information provided with your computer, or the mobile network operator may provide
it separately from the computer.
For information on inserting and removing the SIM, refer to the “Inserting a SIM” and “Removing a SIM”
sections in this chapter.
EV-DO (Evolution Data Optimized), which provides access to networks based on the code division
multiple access (CDMA) telecommunications standard.
●
For CDMA service activation, you may need the HP Mobile Broadband Module Mobile Equipment
Identifier (MEID) to activate mobile broadband service. The MEID number is located on a label inside
the battery bay of your computer.
For information on HP Mobile Broadband and how to activate service with a preferred mobile network
operator, refer to the HP Mobile Broadband information included with your computer. For additional
Inserting a SIM
CAUTION: When inserting a SIM, position the card with the slanted corner as shown in the illustration.
If a SIM is inserted backwards or upside down, the battery may not snap into place properly and could
damage the SIM and the SIM connector.
To prevent damage to the connectors, use minimal force when inserting a SIM.
To insert a SIM:
1. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the
computer on by sliding the power switch. Then shut down the computer through the operating
system.
2. Close the display.
3. Disconnect all external devices connected to the computer.
4. Unplug the power cord from the AC outlet.
Using HP Mobile Broadband (select models only) 31
5. Turn the computer upside down on a flat surface, with the battery bay toward you.
6. Remove the battery.
7. Insert the SIM into the SIM slot, and gently push the SIM into the slot until it is firmly seated.
8. Replace the battery.
NOTE: HP Mobile Broadband is disabled if the battery is not replaced.
9. Turn the computer right-side up, and then reconnect external power and external devices.
10. Turn on the computer.
Removing a SIM
To remove a SIM:
1. Shut down the computer. If you are not sure whether the computer is off or in Hibernation, turn the
computer on by sliding the power switch. Then shut down the computer through the operating
system.
2. Close the display.
3. Disconnect all external devices connected to the computer.
4. Unplug the power cord from the AC outlet.
5. Turn the computer upside down on a flat surface, with the battery bay toward you.
6. Remove the battery.
32 Chapter 3 Internet
7. Press in on the SIM (1), and then remove it from the slot (2).
8. Replace the battery.
9. Turn the computer right-side up, and then reconnect external power and external devices.
10. Reconnect external devices.
11. Turn on the computer.
Using HP Mobile Broadband (select models only) 33
Using HP Mobile Broadband Setup Utility (select models
only)
HP Mobile Broadband Setup Utility provides basic information about setting up HP Mobile Broadband.
NOTE: HP Mobile Broadband Setup Utility is not available in all regions.
When you first turn on HP Mobile Broadband, the Getting Started with HP Mobile Broadband page
opens.
34 Chapter 3 Internet
Using Bluetooth wireless devices
A Bluetooth device provides short-range wireless communications that replace the physical cable
connections that traditionally link electronic devices such as the following:
Computers (desktop, notebook, PDA)
Phones (cellular, smart phone)
●
●
●
●
Imaging devices (printer, camera)
Audio devices (headset, speakers)
Bluetooth devices provide peer-to-peer capability that allows you to set up a personal area network
(PAN) of Bluetooth devices. For information on configuring and using Bluetooth devices, refer to the
Bluetooth software Help.
Bluetooth and Internet Connection Sharing (ICS)
HP does not recommend setting up one computer with Bluetooth as a host and using it as a gateway
through which other computers may connect to the Internet. When two or more computers are connected
using Bluetooth, and Internet Connection Sharing (ICS) is enabled on one of the computers, the other
computers may not be able to connect to the Internet using the Bluetooth network.
The strength of Bluetooth is in synchronizing information transfers between your computer and wireless
devices including cellular phones, printers, cameras, and PDAs. The inability to consistently connect
two or more computers to share the Internet through Bluetooth is a limitation of Bluetooth and the
Windows operating system.
Using Bluetooth wireless devices 35
4 Multimedia
Multimedia features
Your computer includes multimedia features that allow you to listen to music, watch movies, and view
pictures. Your computer may include the following multimedia components:
Integrated speakers for listening to music
●
●
●
Integrated webcam that allows you to capture photographs and videos
Preinstalled multimedia software that allows you to play and manage your music, movies, and
pictures
NOTE: Your computer may not include all of the components listed.
The following sections explain how to identify and use the multimedia components included with your
computer.
Identifying your multimedia components
The following illustration and table describe the multimedia features of the computer.
36 Chapter 4 Multimedia
Component
(1)
Description
Webcam
Captures still photographs and videos.
NOTE: To capture videos, you must install additional
webcam software.
(2)
(3)
(4)
(5)
Webcam light
On: The webcam is in use.
Records sound.
Internal microphone
Speakers (2)
Produce sound.
Volume up hotkey
Increases speaker sound when pressed in combination with
the fn key.
(6)
(7)
(8)
Volume down hotkey
Volume mute hotkey
Decreases speaker sound when pressed in combination with
the fn key.
Mutes speaker sound when pressed in combination with the
fn key.
Audio-out (headphone) jack/Audio-in
(microphone) jack
Produces sound when connected to optional powered stereo
speakers, headphones, earbuds, a headset, or television
audio. Also connects an optional headset microphone.
WARNING! To reduce the risk of personal injury, adjust the
volume before putting on headphones, earbuds, or a headset.
For additional safety information, refer to the Regulatory,
Safety and Environmental Notices.
NOTE: When a device is connected to the jack, the
computer speakers are disabled.
The audio component must have a 4-conductor connector.
Multimedia features 37
Adjusting the volume
You can adjust the volume using the following computer volume action keys:
Computer volume hotkey—A combination of the fn key (1) and either the f8 (2), f10 (3), or f11 (4)
●
function key:
To mute or restore volume, press fn+f8.
To decrease volume, press fn+f10.
To increase volume, press fn+f11.
◦
◦
◦
Windows® volume control:
●
a. Click the Speakers icon in the notification area, at the far right of the taskbar.
b. Increase or decrease the volume by moving the slider up or down. Select the Mute
Speakers icon to mute the volume.
– or –
a. Right-click the Speakers icon in the notification area, and then click Open Volume Mixer.
b. In the Volume Control column, you can increase or decrease the volume by moving the slider
up or down. You can also mute the volume by clicking the Mute Speakers icon.
If the Speakers icon is not displayed in the notification area, follow these steps to add it:
a. Right-click the Show hidden icons icon (the arrow at the left side of the notification area).
b. Click Customize notification icons.
38 Chapter 4 Multimedia
c. Under Behaviors in the Volume section, select Show icon and notifications.
d. Click OK.
Program volume control:
●
Volume can also be adjusted within some programs.
Multimedia software
Your computer includes preinstalled multimedia software that allows you to play music, watch movies,
and view pictures.
Using other preinstalled multimedia software
To locate other preinstalled multimedia software:
Select Start > All Programs, and then open the multimedia program you want to use. For example,
▲
if you want to use Windows Media Player (select models only), click Windows Media Player.
NOTE: Some programs may be located in subfolders.
Installing multimedia software from the Internet
To install multimedia software from the Internet, go to the software manufacturer’s Web site and
follow the instructions.
▲
NOTE: Software downloaded from the Internet may contain viruses. Refer to the “Security” chapter
for more information.
Multimedia software 39
Audio
Your computer has a variety of audio features that allow you to:
Play music using your computer speakers and/or connected external speakers.
Record sound using the internal microphone or an optional external headset microphone.
Download music from the Internet.
●
●
●
●
●
Create multimedia presentations using audio and images.
Transmit sound and images with instant messaging programs.
Connecting external audio devices
WARNING! To reduce the risk of personal injury, adjust the volume before putting on headphones,
earbuds, or a headset. For additional safety information, refer to the Regulatory, Safety and
Environmental Notices.
To connect external devices such as external speakers, headphones, or a headset microphone, refer
to the information provided with the device. For best results, remember the following tips:
Be sure that the device cable has a 4-conductor connector that supports both audio-out
(headphone) and audio-in (microphone).
●
Be sure that the external device cable is securely connected to the jack on your computer.
Be sure to install any drivers required by the external device.
●
●
NOTE: A driver is a required program that acts like a translator between the computer and the
programs that use the computer.
Checking your audio functions
To check the system sound on your computer, follow these steps:
1. Select Start > Control Panel.
2. Click Hardware and Sound.
3. Click Sound.
4. When the Sound window opens, click the Sounds tab. Under Program Events, select any sound
event, such as a beep or alarm, and click the Test button.
You should hear sound through the speakers or through connected headphones.
To check the record functions of the computer, follow these steps:
1. Select Start > All Programs > Accessories > Sound Recorder.
2. Click Start recording and speak into the microphone. Save the file to your desktop.
3. Open Windows Media Player and play back the sound.
40 Chapter 4 Multimedia
NOTE: For best results when recording, speak directly into the microphone and record sound in a
setting free of background noise.
To confirm or change the audio settings on your computer, select Start > Control Panel >
▲
Hardware and Sound > Sound.
Audio 41
Video
Your computer enables you to use a variety of video features:
Watch movies
●
●
●
●
Play games over the Internet
Edit pictures and video to create presentations
Connect external video devices
Connecting an external monitor or projector
Use a VGA cable (purchased separately) to connect an external display, such as a monitor or projector,
to the external monitor port on the computer.
To connect an external monitor or projector:
1. Connect the optional VGA cable to the external monitor port on the computer.
2. Connect the external monitor or projector to the other end of the cable.
NOTE: If a properly connected external monitor or projector does not display a screen image, press
fn+f2 to transfer the image to the external display. Repeatedly pressing fn+f2 alternates the screen
image between the external display and the computer.
42 Chapter 4 Multimedia
Webcam
Your computer includes an integrated webcam, located at the top of the display. The webcam is an input
device that allows you to capture still photographs and videos.
NOTE: To record videos, you must install additional webcam software.
To access the webcam:
1. Select Start > All Programs > ArcSoft WebCam Companion 3 > WebCam Companion 3.
2. Select Capture > Take pictures.
NOTE: The picture is automatically saved in the Documents folder.
Webcam 43
5 Security
Protecting the computer
Standard security features provided by the Windows operating system and the non-Windows Setup
Utility can protect your personal settings and data from a variety of risks.
Follow the procedures in this chapter to use the following features:
Passwords
●
●
●
●
Firewall software
Antivirus support (Norton Internet Security)
Critical security updates
NOTE: Security solutions are designed to act as deterrents, but they may not deter software attacks
or prevent the computer from being mishandled or stolen.
NOTE: Before you send your computer for service, remove all password settings.
Computer risk
Security feature
Unauthorized use of the computer
QuickLock
●
●
●
●
Power-on password
Firewall software
Windows updates
Unauthorized access to data
Unauthorized access to Setup Utility, BIOS settings, and other Administrator password
system identification information
Ongoing or future threats to the computer
Critical security updates from Microsoft
User password
Unauthorized access to a Windows user account
Using passwords
A password is a group of characters that you choose to secure your computer information. Several types
of passwords can be set, depending on how you want to control access to your information. Passwords
can be set in Windows or in the non-Windows Setup Utility preinstalled on the computer.
CAUTION: To prevent being locked out of the computer, record each password you set. Because
most passwords are not displayed as they are set, changed, or deleted, it is essential to record each
password immediately and store it in a secure place.
44 Chapter 5 Security
You can use the same password for a Setup Utility feature and for a Windows security feature. You can
also use the same password for more than one Setup Utility feature.
Use the following guidelines when setting a password in Setup Utility:
A password can be any combination of up to 8 letters and numbers and is case sensitive.
●
●
A password set in Setup Utility must be entered at a Setup Utility prompt. A password set
in Windows must be entered at a Windows prompt.
Use the following tips for creating and saving passwords:
When creating passwords, follow requirements set by the program.
●
●
●
●
Write down your passwords and store them in a secure place away from the computer.
Do not store passwords in a file on the computer.
Do not use your name or other personal information that could be easily discovered by an outsider.
The following sections list Windows and Setup Utility passwords and describe their functions. For
additional information about Windows passwords, such as screen-saver passwords, select Start > Help
and Support.
Passwords set in Windows
Password
Function
Administrator password
Protects administrator-level access to computer contents.
NOTE: This password cannot be used to access Setup Utility
contents.
User password
QuickLock
Protects access to a Windows user account. It also protects
access to the computer contents and must be entered when
you exit Sleep or Hibernation.
Protects the computer by requiring a password to be entered
in the Windows Log On dialog box before you access the
computer. After you set a user or administrator password,
follow these steps:
1. Initiate QuickLock by pressing fn+f6.
2. Exit QuickLock by entering your Windows user or
administrator password.
Passwords set in Setup Utility
Password
Function
Administrator password*
Protects access to Setup Utility.
●
●
After this password is set, it must be entered each time
you access Setup Utility.
CAUTION: If you forget your administrator password, you
cannot access Setup Utility.
Using passwords 45
Password
Function
Power-on password*
Protects access to the computer contents.
●
●
After this password is set, it must be entered each time
you turn on or restart the computer, or exit Hibernation.
CAUTION: If you forget your power-on password, you
cannot turn on or restart the computer, or exit Hibernation.
*For details about each of these passwords, refer to the following topics.
Administrator password
Your administrator password protects the configuration settings and system identification information in
Setup Utility. After this password is set, you must enter it each time you access Setup Utility.
Your administrator password is not interchangeable with an administrator password set in Windows,
nor is it displayed as it is set, entered, changed, or deleted. Be sure that you record your password and
store it in a safe place.
Managing an administrator password
To set, change, or delete this password, follow these steps:
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select Security > Set Administrator Password, and then press enter.
To set an administrator password, type your password in the Enter New Password and
Confirm New Password fields, and then press enter.
●
To change an administrator password, type your current password in the Enter Current
Password field, type a new password in the Enter New Password and Confirm New
Password fields, and then press enter.
●
To delete an administrator password, type your current password in the Enter Password field,
and then press enter 4 times.
●
3. To save your changes and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes.
Your changes go into effect when the computer restarts.
Entering an administrator password
At the Enter Password prompt, type your administrator password, and then press enter. After 3
unsuccessful attempts to enter the administrator password, you must restart the computer and try again.
Power-on password
Your power-on password prevents unauthorized use of the computer. After this password is set, it must
be entered each time you turn on or restart the computer, or exit Hibernation. A power-on password is
not displayed as it is set, entered, changed, or deleted.
46 Chapter 5 Security
Managing a power-on password
To set, change, or delete this password, follow these steps:
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select Security > Set Power-On Password, and then press enter.
To set a power-on password, type your password in the Enter New Password and Confirm
New Password fields, and then press enter.
●
To change a power-on password, type your current password in the Enter Current
Password field, type a new password in the Enter New Password and Confirm New
Password fields, and then press enter.
●
To delete a power-on password, type your current password in the Enter Current
●
Password field, and then press enter 4 times.
3. To save your changes and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes.
Your changes go into effect when the computer restarts.
Entering a power-on password
At the Enter Password prompt, type your password, and then press enter. After 3 unsuccessful attempts
to enter the password, you must restart the computer and try again.
Using passwords 47
Using antivirus software
When you use the computer for e-mail or Internet access, you expose it to computer viruses that can
disable the operating system, programs, or utilities or cause them to function abnormally.
Antivirus software can detect most viruses, destroy them, and in most cases, repair damage they have
caused. To provide ongoing protection against newly discovered viruses, antivirus software must be
kept up to date.
Norton Internet Security, an antivirus program, is preinstalled on the computer.
Your version of Norton Internet Security includes 60 days of free updates. It is strongly
recommended that you protect the computer against new viruses beyond 60 days by purchasing
extended update service. Instructions for using and updating Norton Internet Security software and
for purchasing extended update service are provided within the program.
●
To access Norton Internet Security, or to get more information about it, select Start > All
Programs > Norton Internet Security.
●
NOTE: HP recommends that you always update the antivirus software to help protect your computer.
NOTE: For more information about computer viruses, type viruses in the Search box in Help and
Support.
48 Chapter 5 Security
Using firewall software
When you use the computer for e-mail, network, or Internet access, unauthorized persons may be able
to gain access to the computer, your personal files, and information about you. Use the firewall software
preinstalled on the computer to protect your privacy.
Firewall features include logging and reporting of network activity, and automatic monitoring of all
incoming and outgoing traffic. Refer to the firewall user guide or contact your firewall manufacturer for
more information.
NOTE: Under some circumstances a firewall can block access to Internet games, interfere with printer
or file sharing on a network, or block authorized e-mail attachments. To temporarily resolve the problem,
disable the firewall, perform the task that you want to perform, and then reenable the firewall. To
permanently resolve the problem, reconfigure the firewall.
Using firewall software 49
Installing critical updates
CAUTION: Microsoft sends alerts regarding critical updates. To protect the computer from security
breaches and computer viruses, install all critical updates from Microsoft as soon as you receive an
alert.
Updates to the operating system and other software may have become available after the computer
was shipped. To be sure that all available updates are installed on the computer, observe these
guidelines:
Run Windows Update as soon as possible after you set up your computer. Use the update link at
Start > All Programs > Windows Update.
●
Run Windows Update at regular intervals, such as once a month.
●
●
Obtain updates to Windows and other Microsoft programs, as they are released, from the Microsoft
Web site and through the updates link in Help and Support.
50 Chapter 5 Security
6 Digital cards
Optional digital cards provide secure data storage and convenient data sharing. These cards are often
used with digital media–equipped cameras and PDAs as well as with other devices.
The Digital Media Slot supports the following formats:
Memory Stick (MS)
MS/Pro
●
●
●
●
●
MultiMediaCard (MMC)
Secure Digital (SD) Memory Card
xD-Picture card
Inserting a digital card
CAUTION: To avoid damaging the digital card or the computer, do not insert any type of adapter into
the Digital Media Slot.
CAUTION: To prevent damage to the digital card connectors, use minimal force to insert a digital card.
1. Hold the digital card label-side up, with the connectors facing the computer.
2. Insert the card into the Digital Media Slot, and then push in on the card until it is firmly seated.
You will hear a sound when the device has been detected, and a menu of options may be displayed.
Inserting a digital card 51
Removing a digital card
CAUTION: To prevent loss of information or an unresponsive system, use the following procedure to
safely remove the digital card.
1. Save your information and close all programs associated with the digital card.
NOTE: To stop a data transfer, click Cancel in the operating system Copying window.
2. Stop the digital card:
a. Click the Safely Remove Hardware and Eject Media icon in the notification area, at the far
right of the taskbar.
NOTE: To display the Safely Remove Hardware and Eject Media icon, click the Show
hidden icons icon (the arrow at the left side of the notification area).
b. Click the name of the digital card in the list.
3. Press in on the digital card (1), and then remove the card from the slot (2).
52 Chapter 6 Digital cards
7 USB devices
Using a USB device
Universal Serial Bus (USB) is a hardware interface that can be used to connect an optional external
device, such as a USB keyboard, mouse, drive, printer, scanner, or hub. Devices can be connected to
the system, an optional docking device, or an optional expansion product.
Some USB devices may require additional support software, which is usually included with the device.
For more information about device-specific software, refer to the manufacturer's instructions.
The computer has 3 USB ports, which support USB 1.0, USB 1.1, and USB 2.0 devices. An optional
USB hub, optional docking device, or an optional expansion product provides additional USB ports that
can be used with the computer.
Connecting a USB device
CAUTION: To prevent damage to a USB connector, use minimal force to connect a USB device.
To connect a USB device, connect the USB cable for the device to the USB port.
▲
You will hear a sound when the device has been detected.
NOTE: When you connect a USB device, you may see a message in the notification area to let you
know that the device is recognized by the system.
Using a USB device 53
Removing a USB device
CAUTION: To prevent loss of information or an unresponsive system, use the following procedure to
safely remove a USB device.
CAUTION: To prevent damage to a USB connector, do not pull on the cable to remove the USB device.
To stop and remove a USB device:
1. Double-click the Safely Remove Hardware and Eject Media icon in the notification area, at the
far right of the taskbar.
NOTE: To display the Safely Remove Hardware and Eject Media icon, click the Show hidden
icons icon (the arrow at the left of the notification area).
2. Click the name of the device in the list.
NOTE: If the USB device is not listed, you do not have to stop the device before you remove it.
3. Click Stop, and then click OK.
4. Remove the device.
54 Chapter 7 USB devices
8 Pointing devices and keyboard
Setting pointing device preferences
Use Mouse Properties in Windows® to customize settings for pointing devices, such as button
configuration, click speed, and pointer options.
To access Mouse Properties, select Start > Devices and Printers. Then, right-click the device
representing your computer, and select Mouse settings.
Using pointing devices
Using the TouchPad
To move the pointer, slide your finger across the TouchPad surface in the direction you want the pointer
to go. Use the TouchPad buttons like the corresponding buttons on an external mouse. To scroll up and
down using the TouchPad vertical scroll zone, slide your finger up or down over the lines.
NOTE: If you are using the TouchPad to move the pointer, you must lift your finger off the TouchPad
before moving it to the scroll zone. Simply sliding your finger from the TouchPad to the scroll zone will
not activate the scrolling function.
Connecting an external mouse
You can connect an external USB mouse to the computer using one of the USB ports on the
computer.
Using the keyboard
Using hotkeys
Hotkeys are combinations of the fn key (1) and one of the function keys (2).
The icons on the f1 through f4, and f6, f8, f10, and f11 keys represent the hotkey functions. Hotkey
functions and procedures are discussed in the following sections.
Setting pointing device preferences 55
Function
Initiate Sleep.
Hotkey
fn+f1
Switch the image.
fn+f2
fn+f3
fn+f4
fn+f6
fn+f8
fn+f10
fn+f11
Decrease screen brightness.
Increase screen brightness.
Initiate QuickLock.
Mute or restore speaker sound.
Decrease speaker sound.
Increase speaker sound.
To use a hotkey command on the computer keyboard, follow either of these steps:
Briefly press the fn key, and then briefly press the second key of the hotkey command.
– or –
●
Press and hold down the fn key, briefly press the second key of the hotkey command, and then
release both keys at the same time.
●
Initiating Sleep
Press fn+f1 to initiate Sleep.
When Sleep is initiated, your information is stored in memory, the screen is cleared, and power is
conserved. While the computer is in Sleep, the power light blinks.
56 Chapter 8 Pointing devices and keyboard
CAUTION: To reduce the risk of information loss, save your work before initiating Sleep.
The computer must be on before you can initiate Sleep.
NOTE: If a critical battery level occurs while the computer is in Sleep, the computer initiates
Hibernation and the information stored in memory is saved to the hard drive. The factory setting for
critical battery action is Hibernate, but this setting can be changed in advanced power settings.
To exit Sleep, briefly slide the power switch.
The function of the fn+f1 hotkey can be changed. For example, you can set the fn+f1 hotkey to initiate
Hibernation instead of Sleep.
NOTE: In all Windows operating system windows, references to the sleep button apply to the fn+f1
hotkey.
Switching the screen
Press fn+f2 to switch the screen image among display devices connected to the system. For example,
if a monitor is connected to the computer, pressing fn+f2 alternates the screen image from computer
display to monitor display to simultaneous display on both the computer and the monitor.
NOTE: You must use a VGA cable (purchased separately) to connect an external display, such as a
monitor or projector, to the external monitor port on the computer.
Most external monitors receive video information from the computer using the external VGA video
standard. The fn+f2 hotkey can also alternate images among other devices receiving video information
from the computer.
The following video transmission types, with examples of devices that use them, are supported by the
fn+f2 hotkey:
LCD (device display)
●
●
External VGA (most external monitors)
Decreasing screen brightness
Press fn+f3 to decrease screen brightness. Hold down the hotkey to decrease the brightness level
incrementally.
Increasing screen brightness
Press fn+f4 to increase screen brightness. Hold down the hotkey to increase the brightness level
incrementally.
Initiating QuickLock
Press fn+f6 to initiate the QuickLock security feature.
QuickLock protects your information by displaying the operating system Log On window. While the Log
On window is displayed, the computer cannot be accessed until a Windows user password or a Windows
administrator password is entered.
NOTE: Before you can use QuickLock, you must set a Windows user password or a Windows
administrator password. For instructions, refer to Help and Support.
Using the keyboard 57
To use QuickLock, press fn+f6 to display the Log On window and lock the computer. Then follow the
instructions on the screen to enter your Windows user password or your Windows administrator
password and access the computer.
Muting speaker sound
Press fn+f8 to mute speaker sound. Press the hotkey again to restore speaker sound.
Decreasing speaker sound
Press fn+f10 to decrease speaker sound. Hold down the hotkey to decrease speaker sound
incrementally.
Increasing speaker sound
Press fn+f11 to increase speaker sound. Hold down the hotkey to increase speaker sound
incrementally.
58 Chapter 8 Pointing devices and keyboard
9 Drives
Identifying installed drives
To view the drives installed on the computer, select Start > Computer.
Handling drives
Drives are fragile device components that must be handled with care. Refer to the following cautions
before handling drives. Additional cautions are included with the procedures to which they apply.
Identifying installed drives 59
CAUTION: To reduce the risk of damage to the computer, damage to a drive, or loss of information,
observe these precautions:
Before you move a computer that is connected to an external hard drive, initiate Sleep and allow the
screen to clear, or properly disconnect the external hard drive.
Before handling a drive, discharge static electricity by touching the unpainted metal surface of the drive.
Do not touch the connector pins on a removable drive or on the computer.
Handle a drive carefully; do not drop a drive or place items on it.
Before removing or inserting a drive, shut down the computer. If you are unsure whether the computer
is off, in Sleep, or in Hibernation, turn the computer on and then shut it down through the operating
system.
Do not use excessive force when inserting a drive into a drive bay.
Do not type on the keyboard or move the computer while an optional optical drive is writing to a disc.
The write process is sensitive to vibration.
When the battery is the only source of power, be sure that the battery is sufficiently charged before
writing to media.
Avoid exposing a drive to temperature or humidity extremes.
Avoid exposing a drive to liquids. Do not spray the drive with cleaning products.
Remove media from a drive before removing the drive from the drive bay, or traveling with, shipping, or
storing a drive.
If a drive must be mailed, place the drive in a bubble-pack mailer or other suitable protective packaging
and label the package “FRAGILE.”
Avoid exposing a drive to magnetic fields. Security devices with magnetic fields include airport walk-
through devices and security wands. The airport security devices that check carry-on luggage, such as
conveyor belts, use X-rays instead of magnetism and will not damage a drive.
Using external drives
Removable external drives expand your options for storing and accessing information.
USB drives include the following types:
1.44-megabyte diskette drive
●
●
●
●
●
●
Hard drive module (a hard drive with an adapter attached)
DVD-ROM Drive
DVD/CD-RW Combo Drive
DVD+RW/R and CD-RW Combo Drive
DVD±RW/R and CD-RW Combo Drive
60 Chapter 9 Drives
Using optional external devices
NOTE: For more information about required software and drivers, or to learn which computer port to
use, refer to the manufacturer's instructions.
To connect an external device:
CAUTION: To reduce the risk of damage to the equipment when connecting a powered device, be
sure that the device is turned off and the AC power cord is unplugged.
1. Connect the device.
2. If you are connecting a powered device, plug the device power cord into a grounded AC outlet.
3. Turn on the device.
To disconnect an unpowered external device, turn off the device, and then disconnect it. To disconnect
a powered external device, turn off the device, disconnect it, and then unplug the AC power cord.
Sharing optical drives
Although your computer does not have an installed optical drive, you can easily access software, as
well as install applications and access data, by sharing an optical drive from another computer that has
an optical drive and is on the same wired or wireless network. Sharing drives is a feature of the Windows
operating system that allows a drive on another computer to be made available for other people to use
on a network.
NOTE: For information on setting up a home network and sharing a drive, refer to Help and Support.
NOTE: Some discs, such as DVD movies and game discs, may be copy-protected and therefore
unusable through DVD or CD sharing.
Sharing optical drives 61
10 Memory modules
The computer has one memory module compartment, which is located on the bottom of the computer.
The memory capacity of the computer can be upgraded by replacing the existing memory module in the
memory module slot.
WARNING! To reduce the risk of electric shock and damage to the equipment, unplug the power cord
and remove all batteries before installing a memory module.
CAUTION: Electrostatic discharge (ESD) can damage electronic components. Before beginning any
procedure, ensure that you are discharged of static electricity by touching a grounded metal object.
To add or replace a memory module:
1. Save your work.
2. Shut down the computer and close the display.
If you are not sure whether the computer is off or in Hibernation, turn the computer on by sliding
the power switch. Then shut down the computer through the operating system.
3. Disconnect all external devices connected to the computer.
4. Unplug the power cord from the AC outlet.
5. Turn the computer upside down on a flat surface.
6. Remove the battery from the computer.
7. Using a small Phillips screwdriver, loosen the 2 cover screws (1).
62 Chapter 10 Memory modules
8. Lift the memory module compartment cover (2) away from the computer.
9. Remove the existing memory module:
a. Pull away the retention clips (1) on each side of the memory module.
The memory module tilts up.
CAUTION: To prevent damage to the memory module, hold the memory module by the
edges only. Do not touch the components on the memory module.
b. Grasp the edge of the memory module (2), and gently pull the module out of the memory
module slot.
To protect a memory module after removal, place it in an electrostatic-safe container.
10. Insert a new memory module:
63
CAUTION: To prevent damage to the memory module, hold the memory module by the edges
only. Do not touch the components on the memory module, and do not bend the memory module.
a. Align the notched edge (1) of the memory module with the tab in the memory module slot.
b. With the memory module at a 45-degree angle from the surface of the memory module
compartment, press the module (2) into the memory module slot until it is seated.
c. Gently press the memory module (3) down, applying pressure to both the left and right edges
of the memory module, until the retention clips snap into place.
CAUTION: To prevent damage to the memory module, be sure that you do not bend the
memory module.
11. Align the tabs on the memory module compartment cover with the notches on the computer, and
then close the cover (1).
12. Tighten the 2 cover screws (2).
13. Replace the battery.
64 Chapter 10 Memory modules
14. Turn the computer right-side up, and then reconnect external power and external devices.
15. Turn on the computer.
65
11 Updating software
Updated versions of the software provided with your computer may be available on the HP Web site.
Most software and BIOS updates on the HP Web site are packaged in compressed files called
SoftPaqs.
Some download packages contain a file named Readme.txt, which contains information regarding
installing and troubleshooting the file.
To update the software, follow these steps, which are explained in the remainder of this guide:
1. Identify your computer model, product category, and series or family. Prepare for a system BIOS
update by identifying the BIOS version currently installed on the computer.
If your computer is connected to a network, consult the network administrator before installing any
software updates, especially system BIOS updates.
NOTE: The computer system BIOS is stored on the system ROM. The BIOS initializes the
operating system, determines how the computer will interact with the hardware devices, and
provides for data transfer among hardware devices, including the time and date.
3. Install the updates.
66 Chapter 11 Updating software
Updating the BIOS
To update the BIOS, first determine what BIOS version you currently have and then download and install
the new BIOS.
Determining the BIOS version
To determine whether available BIOS updates contain later BIOS versions than those currently installed
on the computer, you need to know the version of the system BIOS currently installed.
BIOS version information (also known as ROM date and System BIOS) can be displayed by opening
Setup Utility.
To display the BIOS information:
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. If Setup Utility does not open with the system information displayed, use the arrow keys to select
the Main menu.
When the Main menu is selected, BIOS and other system information is displayed.
3. To exit Setup Utility, use the arrow keys to select Exit > Exit Discarding Changes, and then press
enter.
Downloading a BIOS update
CAUTION: To prevent damage to the computer or an unsuccessful installation, download and install
a BIOS update only when the computer is connected to reliable external power using the AC adapter.
Do not download or install a BIOS update while the computer is running on battery power, docked in an
optional docking device, or connected to an optional power source. During the download and installation,
follow these instructions:
Do not disconnect power from the computer by unplugging the power cord from the AC outlet.
Do not shut down the computer or initiate Sleep or Hibernation.
Do not insert, remove, connect, or disconnect any device, cable, or cord.
To download a BIOS update:
1. Access the page on the HP Web site that provides software for your computer:
Select Start > Help and Support > Maintain, and then select the software and drivers update.
2. Follow the instructions on the screen to identify your computer and access the BIOS update you
want to download.
3. At the download area, follow these steps:
a. Identify the BIOS update that is later than the BIOS version currently installed on your
computer. Make a note of the date, name, or other identifier. You may need this information
to locate the update later, after it has been downloaded to your hard drive.
b. Follow the instructions on the screen to download your selection to the hard drive.
Updating the BIOS 67
Make a note of the path to the location on your hard drive where the BIOS update will be
downloaded. You must access this path when you are ready to install the update.
NOTE: If you connect your computer to a network, consult the network administrator before
installing any software updates, especially system BIOS updates.
BIOS installation procedures vary. Follow any instructions that are displayed on the screen after the
download is complete. If no instructions are displayed, follow these steps:
1. Open Windows Explorer by selecting Start > Computer.
2. Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).
3. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the
update.
4. Double-click the file that has an .exe extension (for example, filename.exe).
The BIOS installation begins.
5. Complete the installation by following the instructions on the screen.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded
file from your hard drive.
68 Chapter 11 Updating software
Updating programs and drivers
To download and install software other than a BIOS update, follow these steps:
1. Access the page on the HP Web site that provides software for your computer:
Select Start > Help and Support > Maintain, and then select the software and drivers update.
2. Follow the instructions on the screen to find the software you want to update.
3. At the download area, select the software you want to download and follow the instructions on the
screen.
NOTE: Make a note of the path to the location on your hard drive where the software will be
downloaded. You must access this path when you are ready to install the software.
4. When the download is complete, open Windows Explorer by selecting Start > Computer.
5. Double-click your hard drive designation. The hard drive designation is typically Local Disk (C:).
6. Using the hard drive path you recorded earlier, open the folder on your hard drive that contains the
update.
7. Double-click the file that has an .exe extension (for example, filename.exe).
The installation begins.
8. Complete the installation by following the instructions on the screen.
NOTE: After a message on the screen reports a successful installation, you can delete the downloaded
file from your hard drive.
Updating programs and drivers 69
12 Setup Utility
Starting Setup Utility
Setup Utility is a ROM-based information and customization utility that can be used even when your
Windows operating system is not working.
The utility reports information about the computer and provides settings for startup, security, and other
preferences.
To start Setup Utility:
Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
▲
Using Setup Utility
Changing the language of Setup Utility
The following procedure explains how to change the language of Setup Utility. If Setup Utility is not
already running, begin at step 1. If Setup Utility is already running, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select System Configuration > Language, and then press enter.
3. Use the arrow keys to select a language, and then press enter.
4. When a confirmation prompt with your language selected is displayed, press enter.
5. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Your change goes into effect immediately.
Navigating and selecting in Setup Utility
Because Setup Utility is not Windows based, it does not support the TouchPad. Navigation and selection
are by keystroke.
To choose a menu or a menu item, use the arrow keys.
●
●
To choose an item in a list or to toggle a field, for example an Enable/Disable field, use either the
arrow keys or f5 or f6.
70 Chapter 12 Setup Utility
To select an item, press enter.
●
●
●
To close a text box or return to the menu display, press esc.
To display additional navigation and selection information while Setup Utility is open, press f1.
Displaying system information
The following procedure explains how to display system information in Setup Utility. If Setup Utility is
not open, begin at step 1. If Setup Utility is open, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Select the Main menu. System information such as the system time and date, and identification
information about the computer is displayed.
3. To exit Setup Utility without changing any settings, use the arrow keys to select Exit > Exit
Discarding Changes, and then press enter.
Restoring default settings in Setup Utility
The following procedure explains how to restore Setup Utility default settings. If Setup Utility is not
already running, begin at step 1. If Setup Utility is already running, begin at step 2.
1. Open Setup Utility by turning on or restarting the computer, and then pressing f10 while the “F10
= BIOS Setup Options” message is displayed in the lower-left corner of the screen.
2. Use the arrow keys to select Exit > Load Setup Defaults, and then press enter.
3. When the Setup Confirmation is displayed, press enter.
4. To save your change and exit Setup Utility, use the arrow keys to select Exit > Exit Saving
Changes, and then press enter.
Setup Utility default settings go into effect when the computer restarts.
NOTE: Your password, security, and language settings are not changed when you restore the factory
default settings.
Exiting Setup Utility
You can exit Setup Utility with or without saving changes.
To exit Setup Utility and save your changes from the current session:
●
If Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow
keys to select Exit > Exit Saving Changes, and then press enter.
To exit Setup Utility without saving your changes from the current session:
●
If Setup Utility menus are not visible, press esc to return to the menu display. Then use the arrow
keys to select Exit > Exit Discarding Changes, and then press enter.
After either choice, the computer restarts in Windows.
Using Setup Utility 71
Setup Utility menus
The menu tables in this section provide an overview of Setup Utility options.
NOTE: Some of Setup Utility menu items listed in this chapter may not be supported by your computer.
Main menu
Select
System information
To do this
View and change the system time and date.
●
●
●
View identification information about the computer.
View specification information about the processor, memory size,
and system BIOS.
Security menu
Select
To do this
Administrator password
Power-On Password
Enter, change, or delete an administrator password.
Enter, change, or delete a power-on password.
System Configuration menu
Select
To do this
Language Support
Processor C4 State
Boot Options
Change Setup Utility language.
Enable/disable the processor C4 sleep state.
Set the following boot options:
f10 and f12 Delay (sec.)―Set the delay for the f10 and f12 functions
of Setup Utility in intervals of 5 seconds each (0, 5, 10, 15, 20).
●
●
●
Internal Network Adapter boot―Enable/disable boot from Internal
Network Adapter.
Boot Order―Set the boot order for:
Internal hard drive (select models only)
USB Floppy
◦
◦
◦
◦
◦
◦
◦
USB CD/DVD ROM Drive
USB flash drive
USB Hard drive
USB Card Reader
Network adapter
NOTE: Only the devices attached to the system appear in the
boot order menu.
72 Chapter 12 Setup Utility
Index
A
buttons
removing 52
stopping 52
Digital Media Slot, identifying
display
AC adapter
connecting 14
identifying
AC adapter light, identifying
administrator password
creating 46
left TouchPad
right TouchPad
display switch, identifying
drive light, identifying
drives
C
entering 46
managing 46
cables
LAN 24
antennas
USB 53
VGA 42
caps lock light, identifying
changing Setup Utility
language 70
applications key, Windows
audio devices, connecting
external 40
diskette 60
external 60
hard 60
optical 60
compartments, memory
B
E
battery
module
components
additional hardware
earbuds 6, 37
encryption 29
entering a power-on
password 47
entering an administrator
password 46
calibrating 18
discharging 17
disposing 21
bottom
display
front
identifying
inserting 15
recharging 20
removing 15
storing 21
left-side
right-side
TouchPad
external audio devices,
connecting 40
external monitor port,
battery bay, identifying
cord, power
identifying
F
firewall 28
D
digital card
bay, battery
inserting 51
74 Index
H
function
Windows applications
Windows logo
multimedia software
installing 39
using 39
L
hardware, identifying
labels
Microsoft Certificate of
Authenticity 10
regulatory 10
N
network cable
Hibernation
service tag
connecting 24
exiting 12
latches, battery release
left TouchPad button,
initiated during critical battery
level 17
initiating 12
network jack, identifying
identifying
lights
battery
caps lock
noise suppression circuitry, network
cable 24
hotkeys
decreasing screen
brightness 57
description 55
increasing screen
brightness 57
using 56
O
drive
power
webcam
wireless
P
local area network (LAN)
passwords
administrator 46
power-on 46
ports
power
M
HP Mobile Broadband,
disabled 31
managing a power-on
password 47
managing an administrator
password 46
memory module
inserting 63
removing 63
memory module compartment
cover
hubs 53
connecting 14
conserving 20
I
icons
power connector, identifying
wireless 25
internal display switch,
identifying
internal microphone,
power cord, identifying
power light, identifying
power switch, identifying
power-on password
creating 47
removing 63
replacing 64
entering 47
memory module compartment,
managing 47
identifying
J
product name and number,
computer
jacks
mouse, external
RJ-45 (network)
connecting 55
multimedia components,
identifying 36
K
Q
keys
QuickLock 45
fn
Index 75
R
TouchPad
buttons
identifying
using 55
TouchPad scroll zone,
identifying
regulatory information
HP Mobile Broadband Module
WLAN antennas, identifying
WWAN antennas, identifying
wireless 10
right TouchPad button,
U
USB devices
identifying
RJ-45 (network) jack,
identifying
connecting 53
S
description 53
security cable slot, identifying
removing 54
stopping 54
security, cable slot
V
volume down hotkey,
identifying 37
serial number, computer
service tag
setup, computer
SIM
W
Windows applications key,
inserting 31
removing 32
Sleep
identifying
Windows logo key, identifying
exiting 11
initiating 11
software
wireless antennas
wireless controls
button 26
installing 39
multimedia 39
switches
wireless network (WLAN)
connecting 29
power
corporate WLAN
wireless
connection 29
security 28
T
temperature 21
76 Index
|