FlexCam iCam®
Installation & Operation Manual
ClearOne Communications, Inc. ~ 1825 Research Way, Salt Lake City, UT 84119 ~ tel 1-800-945-7730 ~ fax 1-800-933-5107
3
FlexCam iCam — Introduction
2
FlexCam iCam — Introduction
Important safeguards
Unpacking
Before operating the FlexCam iCam, please read the entire manual thoroughly.The FlexCam
iCam was designed, built and tested for use indoors.The use of a power supply other than the
one provided or outdoor operation has not been tested and could damage the camera or
peripheral equipment and/or create a potentially unsafe operating condition.
Carefully remove the FlexCam iCam unit, cables and power supply from the packaging.
Ensure that you received the following parts:
•
Do not operate the FlexCam iCam if the power cord is damaged or if the camera has been
dropped or damaged. A qualified service technician must examine the FlexCam iCam
before operating.
•
Position the cord so that it will not be tripped over, pulled on or come into contact with hot
surfaces.
•
•
Always unplug the FlexCam iCam from the electrical outlet before cleaning or servicing.
To reduce the risk of electric shock, do not immerse in water or other liquid.
FlexCam iCam
Plug
12 VDC Power Supply
12' S-video cable
Use only the power supply provided with the FlexCam iCam. Use of any unauthorized power
supply will void any and all warranties.
!
Handling the camera
•
All ClearOne cameras are for indoor use only.
Microscope Couplers
26 mm, 28 mm and
34 mm
S-video to composite adapter
FlexCam iCam
Manual
•
Do not use cameras next to food or beverages. Cameras have been tested and approved for
use in chemistry labs. However, be very careful not to spill liquid or dry chemicals or
solvents on the camera.
Figure 1. FlexCam iCam and accessories
•
•
•
•
Do not use cameras right next to working TVs, radios, motors, transformers or magnetic
fields.
ClearOne is not responsible for product damage incurred during shipment.You must make
claims directly with the carrier. Inspect your shipment carefully for obvious signs of
damage. If the shipment appears damaged, retain the original boxes and packing material for
inspection by the carrier. Contact your carrier immediately.
Avoid touching the lens.To clear any dust, blow pressurized air onto the lens. For
accidental smears or smudges, wipe carefully with a lens cleaning cloth.
Clean exterior of camera by wiping with a clean, damp cloth; do not use any abrasive
chemicals.
Use both hands whenever adjusting the neck of the camera; this will avoid any unnecessary
strain on the camera’s base and will keep the camera from tipping over unexpectedly.
•
•
Do not attempt to take the camera apart. There are no user-serviceable components inside.
Do not direct the lens of the camera toward the sun. This may damage the camera.
Operating and storage conditions
Do not store or operate the camera under the following conditions:
•
•
•
•
Outdoors or connected to outdoor or auxiliary power sources.
In environments with high humidity.
In inclement weather.
Under severe vibration.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
5
FlexCam iCam — Introduction
4
FlexCam iCam — Introduction
Product overview
FlexCam iCam application examples
The FlexCam iCam easily connects to a variety of display devices allowing many different
uses in the classroom. You can display presentations, student work or slides on a TV or pro-
jector or use the microscope and optional couplers and eyepiece to share lab work and view
microscopic organisms. Using a USB adapter or a video capture card,you can connect the
camera to a computer to add video or photos to a web site and enhance presentations.
C
D
A
S-video
Microscope
B
TV or Video Monitor
FlexCam iCam
S-video
Figure 2. FlexCam iCam overview
USB
A. Gooseneck.The gooseneck allows you to adjust the camera head/camera lens over the
object to be viewed. Do not bend the gooseneck more than 90° in any direction or attempt
to tie it in a knot. Do not attempt to repair any cracks in the vinyl coating.The gooseneck
is nondetachable and should be replaced only by ClearOne.
PC or Mac
USB Adapter
FlexCam iCam
B. Camera base.The camera base has five rubber feet for non-slip support of the camera.
C. Camera head.The head of the camera unit contains the camera lens, lens holder, focus ring
attachments, connections to gooseneck and all cables.
S-video
D. Camera lens and lens holder.The camera lens is held in place by the lens holder. Both are
permanently attached to the camera head. If you unscrew the lens, take care not to
cross thread the lens when putting it back.
LCD Projector
FlexCam iCam
S-video
Composite
S-video to
composite adapter
FlexCam iCam
VCR
Figure 3. FlexCam iCam Applications
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
7
FlexCam iCam — Making Connections
6
FlexCam iCam — Using the Camera
Using the Camera
Making Connections
To view images on a TV
1. Connect the camera to a TV using the S-video cable or composite adapter.
You can connect the FlexCam iCam to a TV, VCR or LCD projector using the included 12'
S-video cable. If your video supply device requires a composite signal, use the provided
S-video to composite adapter.
2. Switch the TV to video mode by using the switch on the TV front panel or pressing the
corresponding button on the remote control (consult your owner's manual for further
instructions).
You can also connect the FlexCam iCam to a PC or Macintosh using the S-video to USB
Adapter (ClearOne part number 911-171-100).
Note: Not all TVs have video inputs. If your TV only has an antenna input, you will need
a modulator or a VCR with video inputs.
To connect to a TV,VCR or projector
1. Connect the S-Video output of the FlexCam iCam to the input of the display device.
If needed, use the S-video to composite video adapter.
3. Turn camera on using the on/off switch located at the base of the gooseneck.
4. Adjust the flexible gooseneck until the camera is aligned with the subject.
5. Turn the focus ring to the left for close-up or right for distance.
2. Connect the power plug to the power jack on the back of the Flex Cam iCam.
3. Plug the power adapter into the wall.
To record images on a VCR
1. Connect the camera to a VCR using the S-video cable or composite adapter.
2. Switch the VCR to the video-in mode (consult your owner’s manual for instructions).
3. Turn camera on using the on/off switch located at the base of the gooseneck.
4. Turn the VCR/TV switch to VCR and the TV to either channel 3 or 4.
5. Adjust the flexible gooseneck until the camera is aligned with the subject.
6. Turn the focus ring to the left for close-up or right for distance.
7. Press record on the VCR.
Power
adapter
Composite adapter
if required
S-video
Video display
FlexCam iCam
To view images on a LCD projector
1. Connect the camera to a projector using the S-video cable or composite adapter.
2. Turn the projector on (consult your owner’s manual for further instructions).
3. Turn camera on using the on/off switch located at the base of the gooseneck.
4. Adjust the flexible gooseneck until the camera is aligned with the subject.
5. Turn the focus ring to the left for close-up or right for distance.
Figure 4. Connections to a display device
To connect to a computer
•
If your computer has a video capture card, plug the S-video cable into the card. Refer to
the video capture card manual for more information.
or
•
To use the microscope couplers
If your computer does not have a video capture card, you will need to purchase the USB
Adapter. Refer to the USB Adapter manual for more information.
•
Depending on the size of your microscope (28 mm and 34 mm), attach the correct coupler
to the microscope by placing it over the microscope’s original eyepiece.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
9
FlexCam iCam — Troubleshooting
8
FlexCam iCam — Appendix
Troubleshooting
Appendix
If you are experiencing problems with your camera:
Specifications
Video Output
S-video and composite
Gooseneck
20"/50.8 cm
•
•
•
Ensure all camera adapter/cable connections and electrical connections are done correctly
and completely.
Video Format
910-171-101 NTSC
Check your computer, video capture cards, digitizer boards,VCR,TV, etc., for faulty
operation.
Weight
4 lb/1.81 kg
910-171-101 PAL
Check all settings on your camera and adjust them for viewing conditions in the
presentation room.
Power Supply
12 VDC
Exterior Color
Translucent blueberry with black accents
If any component of any camera is damaged, contact ClearOne Technical Support for repair
information.
Operating Temperature
32º F – 104º F/0º C – 40º C
Included Accessories
12' (3.65 m) S-video cable
S-video to RCA adapter
SCART adapter (PAL models)
Microscope couplers
Image Sensor
1
/
3
" (8.5 mm) CMOS
No. of Effective Pixels
Optional Accessories
910-171-320 FlexLiteTM
508(H) x 492(V), 251K pixels NTSC
628(H) x 582(V), 365K pixels PAL
910-171-100 USB adapter
910-171-327 Microscope eyepiece adapter
Resolution
330 TV lines (horizontal)
Focus Range
1
/
4" (6.35 mm) to infinity
Lens
8 mm (.32") D-mount glass lens
Gain Control
Auto
White Balance
Auto
Iris
Auto, electronic with flicker-free
performance
Sensitivity
3 lux
S/N Ratio
>4 adB
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
11
FlexCam iCam — Appendix
10
FlexCam iCam — Appendix
Optional accessories
Contact your ClearOne reseller for more information on the following accessories.
Warranty
ClearOne Communications, Inc. (Manufacturer) warrants that this product is free of defects in both
materials and workmanship. Should any part of this product be defective, the Manufacturer agrees,
at its option, to:
FlexLite™
Repair or replace any defective part free of charge (except transportation charges) for a period of
two years from the date the end user is invoiced for the product, provided the end user returns the
product to ClearOne Communications or an authorized ClearOne dealer according to the Product
Return and Repair statement set forth below;
The FlexLite™ is designed for use with any flexible camera. Dual flexneck top lights attach to
the base of your FlexCam to provide adequate lighting for all subjects. Available in 110 V
(NTSC) and 220 V (PAL) versions.
This warranty excludes assembled products not manufactured by the Manufacturer whether or not
they are incorporated in a Manufacturer product or sold under a Manufacturer part or model
number.
USB adapter
Use the USB adapter for Internet videoconferencing, motion video capture, still frame
capture and video editing.
Product Return and Repair
1. Return to Seller if Purchased Through an Authorized Dealer
a.Proof of purchase date from reseller within warranty period must be provided by the end user.
b. Seller may, at its discretion, provide an immediate exchange or repair or may return the unit to
the Manufacturer for repair.
Microscope eyepiece adapter
Create a firm connection between your camera and microscope with the microscope eyepiece
adapter. Remove the original eyepiece of the microscope and replace with this adapter for a
tighter fit between camera and microscope.
2. Return to Manufacturer
a.An RMA (return merchandise authorization) number must be issued to the end user from
ClearOne technical support.
b. The end user must return the product to ClearOne with proof of purchase (showing purchase
date) for a warranty claim, and display the RMA number on the outside of the shipping package.
To attach the microscope adapter
1. Remove the microscope eyepiece.
This warranty is void if:
A. The product has been damaged by negligence, accident, act of God, or mishandling, or has not
been operated in accordance with the procedures described in the operating and technical
instructions; or,
2. Replace the original eyepiece with the custom eyepiece adapter by sliding the narrow end
into place on the microscope.
B. The product has been altered or repaired by other than the Manufacturer or an authorized
service representative of the Manufacturer; or,
C. Adaptations or accessories other than those manufactured or provided by the Manufacturer have
been made or attached to the product which, in the determination of the Manufacturer, shall have
affected the performance, safety or reliability of the product; or,
D. The product's original serial number has been modified or removed.
NO OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MER-
CHANTABILITY OR FITNESS FOR ANY PARTICULAR USE, APPLIES TO THE PRODUCT.
MANUFACTURER'S MAXIMUM LIABILITY HEREUNDER SHALL BE THE AMOUNT PAID
BY THE END USER FOR THE PRODUCT. No person or entity authorized to assume any obligation
or other liability in connection with the products. No action, regardless of form, arising out of or
relating to the product or this warranty, may be brought by end user more than two (2) years after
the cause of action has accrued.
Eyepiece adapter
Connection to the camera
Original eyepiece
Figure 5. Optional eyepiece attachment
3. Gently push the camera into position.
Manufacturer shall not be liable for punitive, consequential, or incidental damages, expenses, or loss
of revenue or property, inconvenience, or interruption in operation experienced by the end user due to
a malfunction in the purchased product. No warranty service performed on any product shall extend
the applicable warranty period.
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
13
FlexCam iCam — Appendix
12
FlexCam iCam — Appendix
Standard(s) to which Conformity is declared:
In case of unsatisfactory operation, the end user shall promptly notify the Manufacturer at the
address set forth below in writing, giving full particulars as to the defects or unsatisfactory
operation. Upon receipt of such notice, the Manufacturer will give instructions respecting the
shipment of the product, or such other matters as it elects to honor this warranty as above provided.
This warranty does not cover damage to the product during shipping and the Manufacturer assumes
no responsibility for such damage. All shipping costs shall be paid by the customer.
89/336/EEC "Electromagnetic Compatibility (EMC) Directive":
EN 55022: 1994 (Emissions)
Specification for limits and methods of measurement of
radio interference characteristics of information
technology equipment
EN 61000-3-2:1995/A1/A2:1998
EN 61000-3-3:1995
Part 3: Limits - Section 2: Limits for harmonic
current emissions.
This warranty extends only to the original end user and is not assignable or transferable.This
warranty is governed by the laws of the State of Utah, without regard to the conflicts of interests
provisions thereof.
Section 3: Limitation of voltage fluctuations and
flicker in low voltage supply systems for equipment
with rated current up to and including 16 A
ClearOne Communications Inc.
1825 Research Way
EN 55024: 1998 (Immunity)
Information technology equipment -Immunity
characteristics - Limits and methods of
measurement
Salt Lake City, Utah 84119
EN 61000-4-2: 1995/A1:1998
EN 61000-4-3: 1996/A1:1998
EN 61000-4-4: 1995
Electrostatic Discharge
Radiated RF Immunity
Electrical Fast Transients
Lighting Surge
FCC Part 15/ICES-003 Compliance
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC rules and Industry Canada ICES-003.These limits are designed to
provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment.This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to
cause harmful interference, in which case the user will be required to correct the interference at
his/her own expense.
EN 61000-4-5: 1995
EN 61000-4-6: 1996
Conducted RF Immunity
Voltage Dips and Voltage Interruptions
EN 61000-4-11: 1994
73/23/EEC "Low Voltage Directive (LVD)":
IEC 60950-1: 2003
Safety of Information Technology Equipment,
Including Electrical Business Equipment
Operation is subject to the following two conditions: (1) This device may not cause interference, and
(2) This device must accept any interference including interference that may cause undesired
operation of the device.
We, the undersigned, hereby declare that the equipment specified above conforms to the above
Directives and Standards.
Changes or modifications not expressly approved by ClearOne Communications could void the user's
authority to operate the equipment.
Manufacturer
Legal Representative in Europe
European Compliance
This equipment has been approved in accordance with Council Directive 1999/5/EC "Radio
Equipment and Telecommunications Equipment". Compliance of the equipment with the Directive is
attested by the application of the CE mark on the equipment.
EC Declaration of Conformity
Signature
Signature
Application of Council Directive(s):
1999/5/EC Radio equipment and
Telecommunications Terminal Equipment
(R&TTE) Directive
Roger J. Midgley
Full Name
Martin Offwood
Full Name
Project Manager
Position
Managing Director EMEA North
Position
Manufacturer's Name:
Manufacturer's Address:
ClearOne Communications
1825 West Research Way Salt Lake City,
Utah 84119 U.S.A.
Model No.:
FlexCam iCam 910-171-101-PAL
FlexCam iCam Digital 910-171-102-PAL
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
Technical Services Group ~ 1-800-283-5936 (USA) ~ 1-801-974-3760
|