Owner’s manual
Mode d’emploi
INFORMATION FOR USERS:
CHANGES OR MODIFICATIONS TO THIS PRODUCT NOT APPROVED BY THE MANUFACTUR-
ER WILL VOID THE WARRANTY AND WILL VIOLATE FCC APPROVAL.
Manual de instrucciones
1. FEATURES
Tuner
General
Electronic Quartz-Locked PLL Tuning
AM/FM Bands–1 AM, 4 FM
20 FM/5 AM Touchbutton Memory
Seek Up/Down Tuning
Preset Station Scan (PS)
Automatic Station Store (AS)
® FM Reception System
Night Illumination
Digital Quartz Clock
Power ANT Turn On Trigger
Full Information LCD Display
Monitor Mode
■Contents
English
1. FEATURES..................................................................2
2. CONTROLS.................................................................3
3. CASSETTE PRECAUTIONS AND CARE ..................4
4. BUTTON TERMINOLOGY..........................................5
5. OPERATION................................................................6
6. TROUBLESHOOTING ..............................................11
7. ERROR DISPLAYS...................................................11
8. SPECIFICATIONS.....................................................12
DIN Chassis
Switchable Frequency Spacing
Chassis
DIN Chassis with ISO Mounting Capability
Dimensions:
XA311
Tape
Auto Reverse
Locking FF/REW
Hard Permalloy Dual Gutter Head
■Table des matières
Français
7" (178mm) Width × 2" (50mm) Height
AM/FM CASSETTE PLAYER WITH CD
CHANGER CONTROL
× 6" (152mm) Depth
1. CARACTÉRISTIQUES..............................................13
2. COMMANDES.............................................................3
3. PRÉCAUTIONS ET ENTRETIEN DES CASSETTES.......14
4. NOMENCLATURE DES TOUCHES .........................15
5. FONCTIONNEMENT.................................................16
6. DÉPISTAGE DES PANNES......................................21
7. AFFICHAGE DES ERREURS...................................21
8. SPÉCIFICATIONS.....................................................22
•
RADIO AM/FM-LECTEUR DE CASSETTE
AVEC COMMANDE DE CHANGEUR DE CD
Audio
Electronic Audio Controls
(Volume/Bass/Treble/Balance/ Fader)
4-Way Balance Controls
Z-Enhancer with 3 Mode Selector
160 W (40 W × 4) Maximum Power Output
•
■Índice
Español
RADIOCASETE DE AM/FM CON CONTROL
DE CAMBIADOR DE DISCOS COMPACTOS
1. CARACTERÍSTICAS ................................................23
2. CONTROLES..............................................................3
3. PRECAUCIONES Y CUIDADOS DE LOS CASETES......24
4. NOMENCLATURA DE LOS BOTONES...................25
5. OPERACIÓN.............................................................26
6. SOLUCIÓN DE PROBLEMAS..................................31
7. VISUALIZACIONES DE ERROR..............................31
8. ESPECIFICACIONES ...............................................32
Clarion Co., Ltd.
All Rights Reserved. Copyright © 2001: Clarion Co., Ltd.
Printed in China / Imprimé en Chine / Impreso en China
Be sure to unfold and read the next page.
Veuillez déployer et vous référer à la page suivante.
Cerciórese de desplegar y de leer la página siguiente.
PE-1722B
280-7620-00
•
2001/1 (D C)
XA311
2
4. BUTTON TERMINOLOGY
Note:
Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold).
•
1 Up and Down (
and
) Buttons
2 Function Button 1
3 Rotary knob
4 A-M (Audio Mode) Button
5 POWER Button
FUNC (Function) Button
6 BAND (Tuning Mode) Button
7 Z-Ehcr (Z-Enhancer) Button
8 PS/AS (Preset Station Scan/Automatic Station Store) Button
Disc Up and Down Button
9 Eject (Q) Button
0 REW Button
! PROG (Program) Button
@ FF Button
# Play/Pause (s) Button
$ DISP (Display Selector) Button
% RDM (Random play) Button
¥ RPT (Repeat play) Button
& SCN (Scan play) Button
* Preset Buttons
( Function Button 2
XA311
5
5. OPERATION
Note:
Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3 (unfold).
•
Basic Operation
Adjusting the tone
CAUTION
Press A-M button 4 and select the item to
adjust. Each time you press A-M button 4, the
item changes in the following order:
“BASS” ➜ “TREB” ➜ “BAL” ➜ “FAD” ➜
Function mode...
When this unit is turned on, starting and stop-
ping the engine of a car with its volume raised
to the maximum level may harm your hearing.
Be careful about adjusting the volume.
1) Press the POWER button 5.
To turn the power off, press the POWER button
for at least 1 second.
*
Adjusting the bass
1. Press A-M button 4 and select “BASS”.
2) Press the FUNC button 5 to select another
operation mode. The mode switches as fol-
lows each time the FUNC button is pressed:
Radio ➜ Tape ➜ CD changer ➜ Radio
2. Turning the Rotary knob
3
clockwise
emphasizes the bass; turning it counter-
clockwise attenuates the bass.
The factory default setting is “0”. (Adjustment
range: –6 to +6)
If a component is not connected, that operation
mode cannot be selected.
*
*
“CASS” appears when no tape is loaded in the
source unit, and “DISC” appears when no disc is
loaded in the CD changer.
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.
*
Adjusting the volume
Adjusting the treble
Turning the Rotary knob 3 clockwise increases
the volume; turning it counterclockwise decreas-
es the volume.
1. Press A-M button 4 and select “TREB”.
2. Turning the Rotary knob
3
clockwise
emphasizes the treble; turning it counter-
clockwise attenuates the treble.
The volume level is from 0 (minimum) to 33 (maxi-
mum).
*
The factory default setting is “0”. (Adjustment
range: –6 to +6)
*
Setting the Z-enhancer
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.
This unit comes with 3 types of sound tone
effects stored in memory. Select the one you
prefer.
The factory default setting is “OFF”.
*
Adjusting the balance
Each time you press Z-EHCR button 7, the tone
effect changes in the following order:
1. Press A-M button 4 and select “BAL”.
“Z-ENHANCER 1” ➜ “Z-ENHANCER 2” ➜ “Z-
ENHANCER 3” ➜ “OFF” ➜ “Z-ENHANCER
1”...
2. Turning the Rotary knob
3
clockwise
emphasizes the sound from the right speak-
er; turning it counterclockwise emphasizes
the sound from the left speaker.
• Z-ENHANCER 1 : bass emphasized
• Z-ENHANCER 2 : treble emphasized
The factory default setting is “0”. (Adjustment
range: L9 to R9)
*
• Z-ENHANCER 3 : bass and treble empha-
sized
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.
• OFF
: no sound effect
6
XA311
Basic Operation
Tape Operation
Adjusting the fader
Loading Tapes
Insert the cassette tape into the Cassette inser-
tion slot with the side on which the tape is
exposed facing the right. Playback starts auto-
matically.
1. Press A-M button 4 and select “FAD”.
2. Turning the Rotary knob
3
clockwise
emphasizes the sound from the front speak-
ers; turning it counterclockwise emphasizes
the sound from the rear speakers.
When the end of the cassette tape is reached, the
*
auto reverse mechanism is activated and the other
side of the tape begins playing automatically.
The factory default setting is “0”. (Adjustment
range: F9 to R9)
*
Note:
3. When the adjustment is complete, press A-M
button 4 several times until the function
mode is reached.
Fully insert the cassette tape into the cassette inser-
•
tion slot.
Listening to a tape which is already loaded
Press the FUNC button 5 to select the tape
mode. Playback begins automatically.
Switching the Display
While pressing the BAND button 6, press the
DISP button $ to enter the clock display mode.
Main display ➜ Clock display ➜ Main display
Ejecting Cassette Tapes
Press the Eject button 9. The cassette tape is
ejected.
Setting the Clock
1) While pressing the BAND button 6, press
the DISP button $ to enter the clock display
mode.
The radio mode is selected automatically 4 seconds
after ejecting the tape.
*
2) While pressing the BAND button 6, press
and hold the DISP button $ for 2 seconds or
more. This enables the clock editing mode.
Fast-Forwarding and Rewinding
Use the FF button @ and REW buttons 0.
: Press this to fast-forward the tape.
: Press this to rewind the tape.
The editable fields will be indicated when the dis-
*
play flashes.
3) To move between the hour and minute fields,
use the Up (hour) and Down (minute) buttons
1.
It is possible to listen to the radio during fast-forward,
rewind or search operations.
*
4) To store the clock setting, press the BAND
Switching to the Other Side of the
Tape
Press the PROG button ! both the FF button
@ and REW button 0 together at the same
time. Playback is switched automatically to the
other side of the cassette tape.
button 6.
Notes:
If you select another operation mode before complet-
ing the above procedure, the clock setting operation
will be canceled.
•
Removing the vehicle’s battery for a check or repair
will cause the clock to reset to 1:00. Set the clock
again if this happens.
•
XA311
7
Radio Operation
FM Reception
Presetting Stations
For enhanced FM performance the
tuner includes signal actuated stereo control
A total of 25 stations can be preset, 5 each for
the FM1, FM2, FM3, FM4 and AM bands.
®
and Multipath noise reduction circuits.
Note:
When a station is preset, the station previously stored
in the memory at that position is cleared.
•
Listening to the Radio
Presetting stations manually
1) Press the FUNC button 5 to select the radio
mode. The radio turns on.
1) Press the BAND button 6 to select the band
at which to store the station.
2) To tune to a desired preset station, first press
the BAND button 6 and select FM1, FM2,
FM3, FM4 or AM.
2) Use the Up and Down buttons 1 to tune in
the station to be preset.
The band changes as follows each time the
BAND button is pressed:
FM1 ➜ FM2 ➜ FM3 ➜ FM4 ➜ AM ➜ FM1
3) Press and hold the corresponding Preset
button * for at least 2 seconds to store the
station into memory.
3) Use the corresponding Preset buttons * to
Auto store function (Automatic Station
Store)
select the desired station.
1) Press the BAND button 6 to select the band
at which to store the stations.
Seek Tuning
2) Press and hold the AS button 8 for at least
2 seconds. Stations with good reception are
automatically stored at preset to the five but-
tons * 1 to 5.
1) Press the BAND button 6 and select the
desired band.
2) Press the Up or Down buttons 1 to seek up
or down the frequency band. Seek tuning
automatically stops when a station is found.
If there are fewer than 5 stations with good recep-
tion, the stations previously stored at the remain-
ing buttons are not cleared.
*
Manual Tuning
Preset Scanning (Preset Station Scan)
1) Press the BAND button 6 to select the
When the PS button 8 is pressed, the preset
memory numbers flash and the stations are
tuned in for 7 seconds each in the order in which
they were stored. Press the PS button again to
cancel the preset scanning mode.
desired band.
2) Press and hold the BAND button for more
than 2 seconds. “MANU” is illuminated on
the display and the manual tuning mode is
selected.
Note:
3) Use the Up and Down buttons 1 to manual-
ly tune up or down the desired frequency
band.
The auto store mode is set if the PS button is pressed
for more than 2 seconds.
•
8
XA311
Radio Operation
CD Changer Mode Operation
Area Change Function
Listening to the Disc
Use this to listen to the radio outside of the
United States.
Press the FUNC button 5 and select the CD
changer mode, then the CD starts playing.
Switchable frequency spacing
This car stereo is initially set to tune in frequen-
cy intervals of 10 kHz for AM and 200 kHz for
FM, the standard calibrations in the U.S. When
using the unit outside the U.S., use the following
procedure to switch the frequency steps and fre-
quency range:
CD CHANGER MODE OPERATION
Press the DISP button $, then the display will show
the play time.
*
Track No. ➜ Play time ➜ Track number
1) Turn the power on and set the tuner mode.
2) Keep the BAND button 6 pressed and while
pressing the button, press the function button
1 2.
Stopping (pausing) Playback
Press the Play/Pause button #.
Press the Play/Pause button # again to resume
playback.
3) Release the buttons.
This procedure changes the factory setting to
9 kHz steps for AM and 50 kHz steps for FM,
the standard calibrations for countries other
than the U.S.
Selection of CDs
Press the Disc Up/Down button 8 to select the
CD you wish to play.
To change the AM/FM setting back to the U.S.
standard frequencies:
1) Set the tuner mode.
Selection Tracks (songs)
Press the SRCH Up/Down button 1.
2) While pressing the BAND button 6, press
the function button 2 (.
: Playback will start from the next track.
3) Release the buttons.
: Playback will start from the beginning of the
track currently playing. When this button is
pressed again, the CD will play from the
previous track.
Your car stereo will once again be calibrated
to receive standard U.S. transmissions.
The chart below lists the frequency specifica-
tions for the U.S. and other countries.
Inital Setting New Setting
(U.S. standard) (outside U.S.)
Fast-Forward and Fast-Backward
: To fast-forward
Frequency
spacing
: To fast-backward
Press and hold the SRCH Up/Down button for 1 sec-
ond or longer will move forward or backward 5 times
faster than normal play, and pressing it for 3 seconds
or longer will do the operation 30 times faster.
10 kHz
9 kHz
*
AM
FM
Frequency
range
530 to
1710 kHz
531 to
1629 kHz
Frequency
spacing
200 kHz
87.9 to
50 kHz
87.5 to
Frequency
range
107.9 MHz 108 MHz
XA311
9
CD Changer Mode Operation
Scan Play (Intro Music Scan)
Press the SCN button &, then the display
shows “SCN”, then the CD will play the first 10
seconds of all the tracks of all CDs. Press the
SCN button & again to disengage the unit from
scan play.
A scan play will start from the track following the one
currently playing.
*
Disc scan play
Press and hold the SCN button & for 2 seconds
or longer, then the display will show “
”
and “SCN”, and plays the first 10 seconds of the
first song of all the CDs in the CD changer.
Press the SCN button & again to disengage the
unit from disc play.
A scan play will start from the first tracks of next CDs
following the one currently playing.
*
Repeat Play
Press the RPT button ¥, then the display
shows “RPT”, then the track currently playing
will be played repeatedly. Press the RPT button
¥ again to disengage the unit from repeat play.
Disc repeat play
Press and hold the RPT button ¥ for 2 seconds
or longer, then the display shows both the
“
” and “RPT”, then the disc currently
being played will be played repeatedly.
Press the RPT button ¥ again to disengage the
unit from disc repeat play.
Random Play
Press the RDM button % then the display will
show “RDM”, then the entire tracks on the disc
will be played at random.
Press the RDM button % again to disengage
the unit from disc random play.
10
XA311
6. TROUBLESHOOTING
Problem
Cause
Measure
Fuse is blown.
Replace with a fuse of the same
amperage as the old fuse.
Power does not turn on
(or no sound is produced)
Connections are improper. Read the attached “Installation/Wire
Connection Guide” once again and
wire properly.
Sound quality is poor.
Playback head is dirty.
Use a cleaning tape, etc. to clean the
head.
No sound while unit can
be operated.
Power ANT lead is shorted
to the ground.
Turn the unit off, first.
Remove all connecting wires from the
power ANT lead, and turn the unit on,
then re-connect a wire one by one to
the power ANT lead.
When sound is muted again, check
the unit with a wire connected last.
7. ERROR DISPLAYS
■ To protect the system, this unit has been equipped with self diagnostic functions. If a fault arises, a
warning is issued by various error displays. Follow the corrective measures and remove the fault.
Error Display
Corrective Measure
This error display indicates that a fault has arisen in the mechanism of the
source unit or CD changer (for example, the disc cannot be changed or
ejected).
Er 2
➜ Check the source unit and CD changer.
This error display indicates that the pickup focus is off because of a
scratched disc or some other factor during source unit or CD changer play.
➜ Check the compact disc.
Er 3
Er 6
This indicates that the CD’s TOC (table of contents) cannot be read, for
example because the selected disc is upside-down.
XA311
11
8. SPECIFICATIONS
FM Tuner
General
Frequency Range……87.9 MHz to 107.9 MHz
Usable Sensitivity……11 dBf
Power Supply Voltage
……14.4 V DC (10.8 V to 15.6 V allowable)
Current Consumption…… Less than 10 A
Speaker Impedance
……4 Ω (4 Ω to 8 Ω allowable)
Weight……2.87 lb. (1.3 kg)
Dimensions
50 dB Quieting Sensitivity……17 dBf
Alternate Channel Selectivity……75 dB
Stereo Separation (1 kHz)……35 dB
Frequency Response (±3 dB)
……30 Hz to 15 kHz
……7" (178 mm) Width × 2" (50 mm) Height
× 6" (152 mm) Depth
AM Tuner
7"
2"
(178 mm)
(50 mm)
Frequency Range……530 kHz to 1,710 kHz
Usable Sensitivity……25 µV
"
Tape
Wow & Flutter (WRMS)……0.1%
Channel Separation (1 kHz)……45 dB
Signal to Noise Ratio……120 µs (normal): 52 dB
Frequency Response (±3 dB)
"
7-3/8"
(188 mm)
2-1/4"
(58 mm)
120 µs (normal)……30 Hz to 16 kHz
Notes:
Specifications comply with EIA Standards.
•
•
Power Amplifier
Specifications and design are subject to change with-
out notice for further improvement.
Maximum Power Output……160 W (40 W × 4ch)
Continuous Average Power Output
……15 W × 4, into 4 Ω, 20 Hz to 20 kHz,
1% THD
Pre-Amplifier
Bass Control Action (100 Hz)……±10 dB
Treble Control Action (10 kHz)……±10 dB
12
XA311
|