Clarion Co., Ltd.
All Rights Reserved. Copyright © 2002: Clarion Co., Ltd.
QC-6800K
280-7943-00
2002/12 (A·C)
Handling Compact Discs
5. DISPLAY
2. PRECAUTIONS
Use only compact discs bearing the
mark.
The Color LCD Display and the Information Panel on the main unit show the following displays, provid-
ing information about the mode and functions operated.
WARNING
Do not play heart-shaped, octagonal, or other specially shaped compact discs.
Some CDs recorded in CD-R mode may not be usable.
Even when recorded in CD-RW mode, some CDs not be usable.
For your safety, the driver should not watch the TV or operate the controls while driving.
Please note that watching and operating the TV while driving are prohibited by law in
some countries. Also, while driving, keep the volume to a level at which external sounds
can be heard.
Information Panel
Handling
Storage
• New discs may have some roughness around
the edges. If such discs are used, the player
may not work or the sound may skip. Use a
ball-point pen or the like to remove any rough-
ness from the edge of the disc.
• Do not expose compact discs to direct sun-
light or any heat source.
Preset channel indication
Disc number indication
*The disc numbers corresponding to the
discs in the CD or MD or DVD changer
light.
1. When the inside of the car is very cold and
the player is used soon after switching on the
heater, moisture may form on the disc (CD/
MD) or the optical parts of the player and
proper playback may not be possible. If mois-
ture forms on the disc (CD/MD), wipe it off
with a soft cloth. If moisture forms on the op-
tical parts of the player, do not use the player
for about one hour. The condensation will dis-
appear naturally allowing normal operation.
4. TV broadcast reception
• Do not expose compact discs to excess hu-
midity or dust.
When receiving the TV broadcasts, the
strength of the signals changes since the car
is moving, so in some cases it may not be
possible to receive clear pictures.
• Do not expose compact discs to direct heat
from heaters.
Ball-point pen
• TV signals are strongly linear, so reception
is affected by buildings, mountains and
other obstacles.
Roughness
Cleaning
• To remove fingermarks and dust, use a soft
cloth and wipe in a straight line from the cen-
ter of the compact disc to the circumference.
: Volume indication
• Such external factors such as electric train
lines, a high voltage lines, and signal de-
vices may disturb the picture or cause
noise.
∗ If the reception is poor, switch to a station with
good reception.
• Do not use any solvents, such as commer-
cially available cleaners, anti-static spray, or
thinner to clean compact discs.
2. Driving on extremely bumpy roads which
cause severe vibration may cause the sound
to skip.
• Never stick labels on the surface of the com-
pact disc or mark the surface with a pencil or
pen.
• After using special compact disc cleaner, let
the compact disc dry off well before playing it.
Operation status indication
*The frequency, play time, clock, etc. are
displayed.
3. This unit uses a precision mechanism. Even
in the event that trouble arises, never open
the case, disassemble the unit, or lubricate
the rotating parts.
• Never play a compact disc with any cello-
phane tape or other glue on it or with peeling
off marks. If you try to play such a compact
disc, you may not be able to get it back out of
the CD player or it may damage the CD
player.
Caution on Handling
On CDs
• Exercise a good precaution when loading a CD
disc with the panel open.
: Search indication
: Mute indication
• Never turn off the power and remove the unit
• Do not use compact discs that have large
scratches, are misshapen, cracked, etc. Use
of such discs may cause misoperation or
damage.
from the car with a CD loaded.
: Z-enhancer indication
: Stereo indication
: Loudness indication
: Disc indication
• To remove a compact disc from its storage
case, press down on the center of the case
and lift the disc out, holding it carefully by the
edges.
: Repeat indication
: Random indication
• Do not use commercially available CD protec-
tion sheets or discs equipped with stabilizers,
etc. These may damage the disc or cause
breakdown of the internal mechanism.
Be sure to unfold and read the next page.
8
VRX835
VRX835
3
VRX835
4
When the display open
3. CONTROLS /
Main unit /
4. NOMENCLATURE
[A-M] button
[a] [d] button
• Shows the AUDIO MODE menu for tone ad-
justment, etc. Press and hold this button for 1
second or longer to switch the loudness on or
off (LOUD ON/OFF).
• Use this button to select a track in the CD/
DVD video mode and CD/MD/DVD changer
mode.
Names of Buttons
Note:
With the Display closed /
[s] button
• Be sure to read this chapter referring to the front diagrams of chapter “3. CONTROLS” on page 5 (unfold).
[ADJ] button
• Shows the ADJUST MODE menu to change
the settings.
• Press to enter the play pause mode in the CD/
DVD video mode and CD/MD/DVD changer
mode. Press to resume playback.
[
]
[
]
TILT
VOL
When the display closed
[
[
[
]
OPEN
[RDM] button
[M.LOCK] button
• The display panel can be switched to a com-
posite screen to lock the monitor.
[VOL] button
[FUNC] button
]
DISP
• Performs random play while in the CD mode
or CD/MD/DVD changer mode. Also performs
disc random play when the button is pressed
and held while in the CD/MD/DVD changer
mode.
• Use this button to increase/decrease the vol-
• Press this button to turn on the power. Press
and hold this button for 1 second or longer to
turn off the power.
[
]
RELEASE
ume.
]
ISR
[s]
[TILT] button
• Use this button to adjust the angle of the liquid
crystal panel in 5 steps.
• Press this button to switch the modes such as
radio.
[
]
[Q]
SENSOR
[
]
[
DIRECT
[
]
]
[
]
SEARCH
BAND
FUNC
[RPT] button
[BAND] button
• Every time this button is pressed and held for
about 2 seconds or longer, the liquid crystal
panel moves forward/backward in 3 steps.
• Plays repeatedly while in the CD mode or CD/
MD/DVD changer mode. When this button is
pressed and held while in the CD/MD/DVD
changer mode, disc repeat play is performed.
• Press this button to switch the receiving bands
for radio/TV mode, etc. Press and hold this
button for 1 second or longer to switch the
SEEK/MANUAL tuning modes.
With the Display open /
[OPEN] button
• Use this button to open/close the liquid crystal
panel.
• Use this button to move to the first track on a
disc in the CD mode.
[SCN] button
• Performs preset scan while in the radio mode.
When the button is pressed and held, auto
store is performed.
• Press and hold this button for about 2 sec-
onds or longer so that the liquid crystal panel
is positioned horizontally when the liquid crys-
tal panel is open. Press the button again to re-
turn the panel to the original position. Even if
the button is not pressed, the panel returns to
the original position after about 10 seconds.
• Use this button to switch to the next disc in the
CD/MD/DVD changer mode.
• Performs scan play for 10 seconds for each
track while in the CD mode and CD/MD/DVD
changer mode. Disc scan play is performed
when the button is pressed and held while in
the CD/ MD/DVD changer mode.
[DIRECT] button
• Use this button to select a preset channel in
the radio/TV mode.
• Use this button to select a disc in the CD/MD/
DVD changer mode.
[DISP] button
[SEARCH] button
• Use this button to tune to a station in the ra-
dio/TV mode.
• Use this button to switch the indications such
as play status on the information panel when
the liquid crystal panel is closed.
• Use this button to call the LCD background
screen setup menu when the liquid crystal
panel is open.
• Press and hold this button for 1 second or
longer to turn off the monitor when the liquid
crystal panel is open.
• Use this button to select a track in the CD/
DVD video mode and CD/MD/DVD changer
mode.
[
]
[
]
]
M.LOCK
A-M
[
ADJ
[Q] button
• Use this button to eject a CD.
• Use this button to switch the display sizes
while in the screen where the TV, VISUAL, or
DVD video, DVD changer mode is suspended.
[s] button
• Use this button to mute the sound.
• Press and hold this button for 1 second or
longer to enter the play pause mode in the
CD/DVD video mode and CD/MD/DVD
changer mode. Press and hold the button for 1
second or longer again to resume playback.
[
]
[
]
RDM
[
]
[
]
RPT
[ISR] button
• Use this button to enter the ISR (Instant sta-
tion recall) standby mode.
[
]
SCN
[
]
[SENSOR]
• Remote control infrared sensor
Note: Be sure to unfold this page and refer to the front diagrams as you read each chapter.
[RELEASE] button
• Use this button to remove the DCP from the
main unit.
5
VRX835
6
VRX835
VRX835
7
Color LCD Display
•Radio/TV mode
: PROGRAM Î WEST COAST (User title)
•CD/CD changer moÎde
: USER TITLE SHINE (User title)
•CD TEXT mode
: DISC TITLE Î SHINE (Disc title)
: TRACK TITLE Î Time has come (Track title)
: ARTIST Î Time has come (Artist)
•MD changer modeÎ
: DISC TITLE
SHINE (Disc title)
: TRACK TITLE Î Time has come (Track title)
•Radio mode : FM1 100.00MHz Pch 1 (Band/Frequency/Preset No.)
: TRACK 02 04 : 07 (Track No./Playback time)
•CD mode
•CD/MD changer mode
: DISC 02 TRACK 02 00 : 45 (Disc No./Track No./Playback time)
•TV mode
: TV1 28CH Pch 1 (Band/Channel/Preset No.)
•VISUAL mode : VISUAL 1 (Band)
•DVD mode
: CHAPTER 01(Chapter No.)
•DVD changer mode
DVD-video : D2 T02 C002 01:00:45
(Disc No./Title No./Chapter No./Playback time)
Video CD : D2 T02 01:00:45 (Disc No./Track No./Playback time)
MP3
CD
: D2 F001 T002 00:45
(Disc No./Folder No./Track No./Playback time)
: D2 T02 00:45 (Disc No./Track No./Playback time)
MOTION/SPRITE pattern display
: Seek/Manual indication
: Stereo indication
: Loudness indication
: Z-enhancer indication
•MANU
Clock time
•ST
•LD
•ZEHCR
Mode name
VRX835
9
OUTLINE OF BUTTON AND TOUCHKEY
OPERATION WHEN THE DISPLAY IS OPEN
6.
∗1
∗2
DISPLAY
∗3
∗1: An example screen indication in the radio
mode
∗2: Press an operation button to switch the screen.
The operation button is [FUNC] button in the
description of operation per mode.
∗3: Touch the screen and the menu correspond-
ing to the play mode is displayed.
∗4
FUNCTION
∗4: Touch an operation key to switch the screen.
The operation key is [FUNCTION] key in the
description of operation per mode.
∗5
∗5: Touch the [RTN] key to return to the previous
screen.
∗6: Touch the [w] key to return to the previous
menu.
∗7: Touch the [z] key to go to the next menu.
CD PLAYER
∗5
10
VRX835
Z-ENHANCER
∗6
∗7
TYPE 2
VTR N/P
NTSC
VRX835
11
7. REMOTE CONTROL
When the panel is open
Receiver for remote control unit
Remote control unit
Operating range: 30˚ in all directions
Signal transmitter
@
5
1
3
4
2
7
6
8
!
9
0
Inserting the Batteries
1. Turn the remote control unit over, then slide
the rear cover in the direction of the arrow.
AA (SUM-3, IECR-6/1.5V)
Batteries
2. Insert the AA (SUM-3, IECR-6/1.5V) batter-
ies that came with the remote control unit
facing in the directions shown in the figure,
then close the rear cover.
Notes:
Using batteries improperly can cause them to ex-
plode. Take note of the following points:
• When replacing batteries, replace both batteries
with new ones.
Rear cover
Rear side
• Do not short-circuit, disassemble or heat batter-
ies.
• Do not dispose of batteries into fire or flames.
• Dispose of spent batteries properly.
12
VRX835
Functions of Remote Control Unit Buttons
DVD changer
CD changer
MD changer
Mode
Radio
CD
TV
Button
1 FUNC
Switches among radio, CD, DVD, CD changer, MD changer, DVD changer, TV and VISUAL.
Power OFF; Press and hold for 1 second or longer.
Plays the first track.
Top play.
2 BAND
Switches reception
band.
Moves the next disc Switches reception
in increasing order. band.
DISC UP
TOP
3 VOLUME
Increases and decreases volume (in all modes).
Moves tracks up
and down.
4 SEARCH
Moves preset chan-
nels up and down.
Moves tracks up
and down.
Moves preset chan-
nels up and down.
When pressed and
held for 1 second:
Fast-forward/
When pressed and
held for 1 second:
Fast-forward/
fast-backward.
fast-backward.
Switches between
playback and
pause.
5 PLAY/PAUSE
No function.
Switches between
playback and
pause.
No function.
6 MUTE
Turns mute on and off.
Recalls ISR radio station in memory.
Press and hold for 2 seconds or longer: Stores current station into ISR memory (radio
mode only).
7 ISR
When the display open, Display mode select. When the display
open and when pressed and held for 1 second: Turns on and off
the monitor. (When the unit is in the DVD changer mode and the
vehicle is moving, operates in the same way on the CD/MD
changer. When the vehicle is stopped, changes the screen size.
When pressed and held: Turns on and off the monitor.)
8 DISP
Switches the TV
mode.
WIDE
When the display close, Switches among main-display, sub-display, clock-display.∗1
Scan play.
9 PS/AS
Preset scan.
Scan play.
Preset scan.
SCN
When pressed and
held for 2 seconds:
Auto store.
When pressed and When pressed and
held for 1 second:
Disc scan play.
held for 2 seconds:
Auto store.
Repeat play.
Random play.
0 AF
No function.
Repeat play.
No function.
RPT
When pressed and
held for 1 second:
Disc repeat play.
! PTY
RDM
No function.
Random play.
Switches between
When pressed and TV and VTR.
held for 1 second:
TV/VTR
Disc random play.
@ Z-EHCR
Switches Z-ENHANCER 1, 2, 3, OFF
Notes:
• Some of the corresponding buttons on the main unit and remote control unit have different functions.
• Please use the dedicated remote control unit provided with a DVD player in the DVD mode or DVD changer
in the DVD changer mode.
∗1: No sub-display appears when the unit is in the DVD changer mode.
VRX835
13
8. DCP
The control panel can be detached to prevent
theft. When detaching the control panel, store it
in the DCP (DETACHABLE CONTROL PANEL)
case to prevent scratches.
2. Press the left side of the DCP carefully to fit
it in place.
We recommend taking the DCP with you when
leaving the car.
DCP
Removing the DCP
1. Turn the power off.
2. Slide the [RELEASE] lever rightward to re-
lease the DCP/Operation Panel.
3. Press the [FUNC] button to turn on the
power.
CAUTION
DCP
• The DCP can easily be damaged by shocks.
After removing it, be careful not to drop it or
subject it to strong shocks.
• If the Operation Panel is kept open, the DCP
may drop due to vibration of the car. This re-
sults in damage to the DCP. So close the Op-
eration Panel or remove the DCP to store into
the case.
3. Pull the DCP toward you and remove it.
• The DCP is an extremely important part. Be
careful not to damage it by pressing on it with
fingernails, screwdrivers, etc.
Note:
DCP
• If the DCP is dirty, wipe off the dirt with a soft, dry
cloth only.
Attaching the DCP
1. Insert the DCP so that the A section on the
right side of the DCP catches on the hook B
on the unit.
VOL
O
L
DCP
B
A
14
VRX835
9. CAUTIONS ON HANDLING
LCD panel/Generalities
For a longer service life, be sure to read the following cautions.
• Be sure to store the LCD panel inside the
main unit when parking the car outdoors for
long period of time. The LCD panel will oper-
ate properly in a temperature range of 0 to
60˚C.
• Do not place anything on the display when the
panel is tilted.
• The remote controller may not work if the re-
mote control sensor is exposed to direct sun-
light.
• Don’t allow any liquids on the set from drinks,
umbrellas etc. Doing so may damage the in-
ternal circuitry.
• In extremely cold weather, the display move-
ment may slow down and the display may
darken, but this is not a malfunction. The dis-
play will work normally when the temperature
increases.
• Do not disassemble or modify the set in any
way. Doing so may result in damage.
• Do not draw the LCD panel out and use it as a
tray. Also, subjecting the LCD panel to shocks
may result in breakage, deformation or other
damage.
• Small black and shiny spots inside the LCD
panel are normal for LCD products.
• The LCD panel may stop temporarily when it
opens or closes, when the engine stops or
when it is cold.
• Do not let cigarettes burn the display. Doing so
may damage or deform the cabinet.
• The touchkeys on the display operate when
slightly touched. Do not press the touchkey
screen with much force.
• If a problem should occur, have the set in-
spected at your store of purchase.
• Do not insert objects or poke in the space be-
tween the LCD panel and the main unit when
the panel is tilted.
• Do not push the case surrounding the
touchkey panel with much force. This may
cause malfunctioning of the touchkeys.
Cleaning
• Cleaning the cabinet
• Cleaning the LCD panel
Use a soft, dry cloth and gently wipe off the
dirt. For tough dirt, apply some neutral deter-
gent diluted in water to a soft cloth, wipe off
the dirt gently, then wipe again with a dry
cloth.
The LCD panel tends to collect dust, so wipe
it off occasionally with a soft cloth. The sur-
face is easily scratched, so do not rub it with
hard objects.
Do not use benzene, thinner, car cleaner, etc.,
as these substances may damage the cabinet
or cause the paint to peel. Also, leaving rub-
ber or plastic products in contact with the
cabinet for long periods of time may cause
stains.
VRX835
15
10. OPERATIONS
Note: Be sure to read this chapter referring to the front diagrams of
chapter “3. CONTROLS” on page 5 (unfold).
Basic Operations
Adjusting the volume
CAUTION
Operate the [VOL] button in the direction of the
+ (up) or – (down) to adjust the volume;
When the unit is turned on, starting and stop-
ping the engine with its volume raised to the
maximum level may harm your hearings. Be
careful about adjusting the volume.
+ : Increases the volume.
– : Decreases the volume.
∗ The volume level indicated in the display is in a
range from 0 (minimum) to 33 (maximum).
Note:
• Use this unit after starting the engine.
ACC or engine
ON position
CAUTION
While driving, keep the volume at a level at
which external sounds can be heard.
Turning on and off the power
Note:
Switching the display
When the panel is closed:
• Be careful about using this unit for a long time
without running the engine. If you drain the car’s
battery too far, you may not be able to start the
engine and this can reduce the service life of the
battery.
Press the [DISP] button to select the desired
display.
Each time you press the [DISP] button, the dis-
play switches in the following order:
1. Press the [FUNC] button.
2. The illumination and display on the unit light
up. The unit automatically remembers its last
operation mode and will automatically switch
to display that mode.
MAIN Display
3. Press and hold the [FUNC] button for 1 sec-
ond or longer to turn off the power for the
unit.
SUB Display
Note:
• About the “SYSTEM CHECK”
Clock Time Display
The confirmation of connected equipment must
be performed for this unit only when the wiring
connection is complete and power is turned on to
the unit first. When the power is supplied, “SYS-
TEM” and “PUSH PWR” appear alternately in the
display. Press the [FUNC] button, the system
check starts inside the unit. When “COMPLETE”
appears, press once again the [FUNC] button.
MAIN Display
Notes:
• Once selected, the preferred display becomes the
default display. When a function adjustment such
as volume is made, the display momentarily
switches to that function’s display, then returns
Selecting a mode
1. Press the [FUNC] button to change the mode
of operation.
back to the preferred display several seconds af-
ter the adjustment.
• If a title has been input, it is shown in the SUB
display. If no title has been input, “NO TITLE” ap-
pears in the display. To input a title, refer to the
subsection “Entering titles” in “Other Functions”
section.
• For CD, MD and TV, some special characters of
the title will not be displayed on the Information
Panel of the DCP. In this case, those characters
will only be left blank.
2. Each time you press the [FUNC] button, the
mode of operation changes in the following
order:
Radio mode ➜ CD mode ➜ DVD video
mode ➜ CD changer mode ➜ MD changer
mode ➜ DVD changer mode ➜ TV mode ➜
VISUAL mode ➜ Radio mode...
∗ External equipment not connected with
CeNET is not selected.
• No sub-display appears when the unit is in the
DVD changer mode.
16
VRX835
Basic Operations
Showing a mode display
Adjusting the angel, etc. of the
liquid crystal panel
The angle of the liquid crystal panel or protrud-
ing amount of the panel from the mounting sur-
face can be adjusted depending on the mount-
ing angle of the unit or light coming into the car.
When the panel is open:
Touch the menu screen switching touchkey
when the main screen is being displayed to
show the menu screen.
Touch the Title List Select key (--- SELECT) on
the menu screen to show the Title List display.
To adjust the angle
In the Title List display, the titles of items stored
in the [DIRECT] buttons 1 to 6 are listed.
Every time the [TILT] button is pressed, the liq-
uid crystal panel tilts forward or backward at up
to about 20 degrees. The adjusted angel is
stored in memory.
Opening and turning the display
WARNING
• To prevent the battery from going dead,
operate this unit with the engine run-
ning, if possible.
• When the liquid crystal panel is operating,
be careful not to get your hand or finger
caught between the panel and main unit
or the instrument panel of the car.
Standing up the liquid crystal panel
Press the [OPEN] button and the liquid crystal
panel comes out and stand up automatically.
Note:
• Do not move the liquid crystal panel by hand.
To adjust the slide position
Press and hold the [TILT] button and release
when a beep is heard.
The liquid crystal panel slides forward or back-
ward. The adjusted slide position is stored in
memory.
∗ While the liquid crystal panel is opening or
closing, the LED blinks.
Note:
• If the liquid crystal panel stops in the middle of its
operation, press the [OPEN] button to house the
panel and press the button again to stand it up.
The unit enters the same display mode as the dis-
play was turned off the last time.
Housing the liquid crystal panel
Press the [OPEN] button and the liquid crystal
panel is housed automatically.
Note:
• When leaving this unit unused for a long period of
time or leaving your car, be sure to house the liq-
uid crystal panel into the main unit.
VRX835
17
Basic Operations
When the panel is closed:
Turning the liquid crystal panel
horizontal (Air conditioner
operation mode)
When the way the liquid crystal panel is
mounted hinders the operation of the air condi-
tioner, the position of the panel can be turned
horizontal temporarily.
Each time you press the [Z-EHCR] button of the
remote control unit, the tone effect changes in
the following order:
“Z-EHCR 1” ➜ “Z-EHCR 2” ➜ “Z-EHCR 3” ➜
“Z-EHCR OFF” ➜ “Z-EHCR 1”...
Note:
• When the panel is closed, operations can only be
made through the remote control unit.
1. Press and hold the [OPEN] button when the
liquid crystal panel is upright, and release
the button when a beep is heard.
When the panel is open:
2. The liquid crystal panel turns horizontal.
1. Press the [A-M] button to change into the
∗ Press the [OPEN] button again when the liquid
crystal panel is in the horizontal position, and
the panel returns to the original position.
AUDIO-MODE display.
2. Touch the [Z-ENHANCER] key when the AU-
DIO-MODE screen is being displayed to show
the Z-ENHANCER type selection screen.
∗ Even if the button is not operated for about 10
seconds, the panel returns to the original
position with a warning sound.
3. When the Z-ENHANCER type selection
screen is displayed, touch the key for the de-
sirable type to select it.
Turning on and off the monitor
Pressing and holding the [DISP] button for 1
second or longer turns the monitor off. To return
to the monitor on, press the [DISP] button once
again.
• “TYPE 1” (Z-Enhancer 1)
• “TYPE 2” (Z-Enhancer 2)
• “TYPE 3” (Z-Enhancer 3)
• “OFF” (Z-Enhancer off)
∗ When a button is pressed or during security moni-
toring, the monitor-off mode is canceled.
4. When the setting is finished, touch the [RTN]
key to return to the AUDIO-MODE screen.
Touch the [RTN] key on the AUDIO-MODE
screen to return to the STANDARD display.
∗ To return from the Z-ENHANCER type
selection display to the STANDARD display,
press the [A-M] button once again.
Mute
Each time you press the [s] button, mute is
turned on and off.
“MUTE” appears when mute is turned on.
Setting the Z-enhancer
Adjusting the Z-enhancer
This unit comes with 3 types of sound tone effect
stored in memory. Select the one you prefer.
Notes:
• The Z-enhancer cannot be adjusted when it is
turned off.
∗ The factory default setting is “Z-EHCR OFF”.
When a Z-enhancer comes on (1-3), “Z-EHCR”
appears in the display.
•
This function is enabled only when the panel is open.
1. Press the [A-M] button to change into the
AUDIO-MODE display.
• “Z-EHCR 1” (Z-Enhancer 1):
2. Touch the [Z-EHCR LV] key when the AUDIO-
MODE screen is being displayed to show the
Z-ENHANCER level adjustment screen.
Setting emphasizing bass.
• “Z-EHCR 2” (Z-Enhancer 2):
Setting emphasizing treble.
3. Touch the [w] or [z] key to adjust to the de-
• “Z-EHCR 3” (Z-Enhancer 3):
Setting emphasizing bass and
treble.
sirable level.
∗ When type 1 is selected, you can adjust the
bass in the range of 2.
• “Z-EHCR OFF” (Z-Enhancer off):
Neither bass nor treble are em-
phasized by the Z-enhancer.
∗ When type 2 is selected, you can adjust the
treble in the range of 2.
∗ When type 3 is selected, you can adjust the
bass and treble in the range of 2.
Note:
• Incapable of operation when connecting DSP
(DPH910) and DVD player (DVS9755z).
4. When adjustment is finished, touch the [RTN]
key on the Z-ENHANCER level adjustment
18
VRX835
Basic Operations
screen to return to the AUDIO-MODE screen.
Turning on/off the loudness
Touch the [RTN] key on the AUDIO-MODE
screen to return to the STANDARD display.
∗ To return from the Z-Enhancer level mode
display to the STANDARD display, press the
[A-M] button once again.
The loudness effect emphasizes the bass and
treble to create a natural sound tone. When you
are listening to music at a low volume, it is rec-
ommended to use the loudness effect.
∗
This function is enabled only when the panel is open.
1. Press the [A-M] button for 1 second or longer
to select Loudness ON. The “LD” indicator
lights in the display.
Adjusting the bass and treble
Notes:
•
This function is enabled only when the panel is open.
2. Press the [A-M] button for 1 second or longer
to select Loudness OFF. The “LD” indicator
goes off.
• This function can be adjusted only when the Z-
enhancer is OFF.
1. Press the [A-M] button to change into the
Note:
AUDIO-MODE display.
• When using a sold separately digital sound pro-
cessor (DPH910) or DVD player (DVS9755z), a
feature called auto loudness is selected. This
function is different from the loudness effect. For
further details on the auto loudness feature, refer
to the subsection “Output adjustment of auto
loudness, subwoofer and playback band”.
2. Touch the [BAS/TREB] key when the AUDIO-
MODE screen is being displayed to show the
BASS/TREBLE LEVEL adjustment screen.
3. Touch the [w] or [z] key to adjust to the
desirable BASS/TREBLE level (adjustment
range: from -6 to 6).
4. When adjustment is finished, touch the [RTN]
key on the BASS/TREBLE LEVEL adjustment
screen to return to the AUDIO-MODE screen.
Changing the setting of the display
background
Touch the [RTN] key on the AUDIO-MODE
screen to return to the STANDARD display.
∗ To return from the BASS/TREBLE LEVEL
mode display to the STANDARD display, press
the [A-M] button once again.
WARNING
Perform the setting of this function the car
is stopped with the parking break applied.
1. Press the [DISP] button to show the back-
ground setup menu.
Adjusting the balance and fader
2. Touch the setting key to show the setup dis-
play.
Note:
•
This function is enabled only when the panel is open.
GTo set up the pattern and colour of the wall
paper
1. Press the [A-M] button to change into the
AUDIO-MODE display.
2-1. Touch the [WALL PAPER] key to select
2. Touch the [BAL/FAD] key when the AUDIO-
MODE screen is being displayed to show the
BALANCE/FADER adjustment screen.
“PATTERN” or “COLOR”.
2-2. Touch the [PATTERN] or [COLOR] key
to set a desired pattern or colour.
3. Touch the [Î] or [Å] key to adjust to the de-
2-3. Touch a desired [PATTERN] or
sirable balance.
[COLOR] key.
Adjusting range of the balance: left 13 to right 13
GTo set up the motion pattern
4. Touch the [w] or [z] key to adjust to the de-
2-1. Touch the [MOTION PATTERN] key to
sirable fader.
set a desired motion pattern.
Adjusting range of the fader: front 12 / rear 12
2-2. Touch a desired [MOTION PATTERN] key.
5. When adjustment is finished, touch the [RTN]
key on the BALANCE/FADER adjustment
screen to return to the AUDIO-MODE screen.
GTo set up the sprite pattern
2-1. Touch the [SPRITE PATTERN] key to
set a desired sprite pattern.
Touch the [RTN] key on the AUDIO-MODE
screen to return to the STANDARD display.
2-2. Touch a desired [SPRITE PATTERN] key.
∗ To return from the BALANCE/FADER mode
display to the STANDARD display, press the
[A-M] button once again.
3. Press the [DISP] button again or touch the
[RTN] key two times to return to the STAN-
DARD display.
VRX835
19
Radio Operations
3. Press the right (d)or left (a) side of the
[SEARCH] button to automatically seek a
station.
FM reception
For enhanced FM performance the
® tuner includes signal actuated stereo control,
Enhanced Multi AGC, Impulse noise reduction
curcuits and Multipath noise reduction circuits.
When the right (d) side of the [SEARCH]
button is pressed, the station is sought in the
direction of higher frequencies; when the left
(a) side of the [SEARCH] button is
pressed, the station is sought in the direction
of lower frequencies.
Changing the reception area
This unit is initially set to outside USA frequency
intervals of 9kHz for AM and 50kHz for FM.
When using it in the USA, the frequency
reception range can be switched to the intervals
below.
Manual tuning
There are 2 ways available: Quick tuning and
step tuning.
GSetting the reception area
When you are in the step tuning mode, the fre-
quency changes one step at a time. In quick tun-
ing mode, you can quickly tune the desired fre-
quency.
While pressing [DISP] button, each time you
press and hold the number “6” of the [DIRECT]
buttons for 2 seconds or longer, the reception
area switches from inside the USA to outside
the USA or from outside the USA to inside the
USA.
1. Press the [BAND] button and select the de-
sired band. (FM or AM)
∗ If “MANU” is not lit in the display (or when the
∗ Any station preset memories are lost when the re-
ception area is changed.
panel is closed, if the indicator “
” is lit),
press and hold the [BAND] button for 1
second or longer. “MANU” appears in the
display (or when the panel is closed, the
Listening to the radio
1. Press the [FUNC] button and select the RA-
DIO mode. The frequency is displayed.
indicator “
” goes off) and manual tuning
is now available.
2. Press the [BAND] button and select the radio
band. Each time the button is pressed, the
radio reception band changes in the following
order:
2. Tune into a station.
G Quick tuning:
Press and hold the right (d) or left (a)
side of the [SEARCH] button for 1 second or
longer to tune in a station.
FM1 ➜ FM2 ➜ FM3 ➜ AM ➜ FM1...
3. Press the right (d) or left (a) side of the
[SEARCH] button to tune in the desired sta-
tion.
G Step tuning:
Press the right (d) or left (a) side of the
[SEARCH] button to manually tune in a sta-
tion.
Tuning
There are 3 types of tuning mode available,
seek tuning, manual tuning and preset tuning.
Recalling a preset station
A total of 24 preset positions (6-FM1, 6-FM2, 6-
FM3, 6-AM) exists to store individual radio sta-
tions in memory. Pressing the corresponding
[DIRECT] button recalls the stored radio fre-
quency automatically.
Seek tuning
1. Press the [BAND] button and select the de-
sired band. (FM or AM)
1. Press the [BAND] button and select the de-
2. Tune in to a station.
sired band. (FM or AM)
∗ If “MANU” is lit in the display (or when the
panel is closed, if the indication “
lit) press and hold the [BAND] button for 1
second or longer. “MANU” in the display goes
off (or when the panel is close the indication
2. Press the corresponding [DIRECT] button to
” is not
recall the stored station.
∗ Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store that station
into preset memory.
“
” lights) and seek tuning is now
available.
∗ When the panel is open, the same operation
is also available by using the [a] and [d]
button in the panel.
20
VRX835
Radio Operations
Manual memory
Instant station recall (ISR)
1. Press the [BAND] button and select the de-
sired band. (FM or AM)
Instant station recall is a special radio preset
that instantly accesses a favorite radio station at
a touch of a button. The ISR function even oper-
ates with the unit in other modes.
2. Select the desired station with seek tuning,
manual tuning, or preset tuning.
GISR memory
3. Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
station into preset memory.
1. Select the station that you wish to store in
ISR memory.
2. Press and hold [ISR] button for 2 seconds or
longer.
Auto store
GRecalling a station with ISR
Auto store is a function for storing up to 6 sta-
tions that are automatically tuned in sequentially.
If 6 receivable stations cannot be received, a
previously stored station remains unoverwritten
at the memory position.
In any mode, press [ISR] button to turn on the
radio function and tune the selected radio sta-
tion. “ISR” appears in the display. Press [ISR]
button again to return to the previous mode.
1. Press the [BAND] button and select the de-
sired band. (FM or AM)
2. Touch the MENU display switching touchkey
when the MAIN display is showing and the
MENU display appears.
3. Touch the [SUB MODE] key in the MENU
display and the [AUTO STORE] key appears
in the display.
4. Touch and hold the [AUTO STORE] key for 2
seconds or longer.
The stations with good reception are stored
automatically to the preset channels.
∗ The same operation is also available by using
the [SCN] button for 1 second or longer in the
panel.
Preset scan
Preset scan receives the stations stored in pre-
set memory in order. This function is useful
when searching for desired station in memory.
1. Touch the MENU display switching touchkey
when the MAIN display is showing and the
MENU display appears.
2. Touch the [SUB MODE] key in the MENU
display and the [PRESET SCAN] key ap-
pears in the display.
3. Touch the [PRESET SCAN] key to start pre-
set scan.
4. When the desired station is turned in, touch
the [PRESET SCAN] key again to continue
receiving that station.
∗ The same operation is also available by using
the [SCN] button in the panel.
VRX835
21
CD Operations
Selecting a track
Loading a CD
GTrack-up
1. Insert a CD into the centre of the insertion
slot with the label side facing up. The CD
plays automatically after loading.
1. Press the right (d) side of [SEARCH] but-
ton to move ahead to the beginning of the
next track.
Notes:
• Never insert foreign objects into the CD insertion
slot.
• If the CD is not inserted easily, there may be an-
other CD in the mechanism or the unit may re-
quire service.
2. Each time you press the right (d) side of
[SEARCH] button, the track advances ahead
to the beginning of the next track.
∗ When the panel is open, the same operation
is also available by using the [d] button in the
panel.
• Discs not bearing the
mark and CD-ROMs
cannot be played by this unit.
GTrack-down
1. Press the left (a) side of [SEARCH] button
to move back to the beginning of the current
track.
Loading 8 cm compact discs
∗ No adapter is required to play an 8 cm CD.
2. Press the left (a) side of [SEARCH] button
twice to move to the beginning of the previ-
ous track.
∗ Insert the 8 cm CD into the centre of the insertion
slot.
∗ When the panel is open, the same operation
is also available by using the [a] button in the
panel.
Listening to a CD already inserted
Press [FUNC] button to select the CD mode.
Play starts automatically. If no CD is loaded in
the unit, “NO DISC” appears in the display.
Fast-forward/fast-backward
GFast-forward
Pausing play
1. Press [s] button for 1 second or longer to
pause play. “PAUSE” appears in the display.
Press and hold the right (d) side of [SEARCH]
button for 1 second or longer.
∗ When the panel is open, the same operation is
also available by using the [d] button in the
panel.
2. To resume CD play, press [s] button for 1
second or longer again.
∗ The same operation is also available by using
the [s] key on the menu screen while in the
CD mode.
GFast-backward
Press and hold the left (a) side of [SEARCH]
button for 1 second or longer.
∗ When the panel is open, the same operation
is also available by using the [s] button in
the panel.
∗ When the panel is open, the same operation is
also available by using the [a] button in the
panel.
Ejecting a CD
Top function
The top function resets the CD player to the first
track of the disc. Press [BAND] button to play
the first track (track No. 1) on the disc.
1. Press the [Q] button a CD ejects. “EJECT”
appears in the display.
∗ If a CD (12 cm) is left in the ejected position
for 15 seconds, the CD is automatically
reloaded. (Auto reload)
∗ 8 cm CDs are not auto reloaded. Be sure to
Show the menu screen
remove it when ejected.
Touch the screen to show the menu screen
while the main screen is being shown.
Note:
• If you force a CD into before auto reloading, this
can damage the CD.
∗ To return to the main screen from the menu
screen, touch the [RTN] key.
22
VRX835
CD Operations
Scan play
Displaying CD titles
The scan play locates and plays the first 10 sec-
onds of each track on a disc automatically. This
function continues on the disc until it is can-
celled.
This unit can display title data for CD-text CDs
and user titles input with this unit.
Each time you press and hold the [DISP] button
for 1 second or longer, the title display changes
in the following order.
∗ The scan play is useful when you want to select a
desired track.
When the panel is closed:
1. Touch the [SUB MODE] key in the MENU
“U-TITLE” (user title) ➜ “D-TITLE” (disc title) ➜
“A-TITLE” (artist title) ➜ “T-TITLE” (track title) ➜
“U-TITLE” ...
display to show SUB MODE.
Touch the [TRACK SCAN] key to start scan
play. “TRACK SCAN” lights in the display.
Note:
2. To cancel the scan play, touch the [TRACK
SCAN] key again. “TRACK SCAN” goes off
from the display and the current track contin-
ues to play.
• If the CD playing is not a CD-TEXT CD or no user
title has been input, “NO-TITLE” appears in the
display.
∗ The same operation is also available by using
When the panel is open:
the [SCN] button in the panel.
Each time you touch the [TITLE INDEX] key in
the MENU display, the title display changes in
the following order.
Repeat play
The repeat play continuously plays the current
track. This function continues automatically until
it is cancelled.
When the [TEXT] key is touched, the DISC,
TRACK and ARTIST titles are shown. When the
[USER] key is touched, the user title is shown.
Touching the [INPUT] key switches the screen to
the title input screen.
1. Touch the [SUB MODE] key in the MENU
display to show SUB MODE.
Touch the [TRACK REPEAT] key. “TRACK
REPEAT” lights in the display and current
track is repeated.
G Scrolling a CD-text title
Note:
• This function is enabled only when the panel is
open.
When a CD-text title is longer than 10 charac-
ters, you can scroll the display as follows.
2. To cancel the repeat play, touch the [TRACK
REPEAT] key again. “TRACK REPEAT” goes
off from the display and the normal play re-
sumes.
∗ The same operation is also available by using
the [RPT] button in the panel.
When the panel is open:
1. Display the CD-TEXT TITLE (disk & track &
artist).
Random play
The random play selects and plays individual
tracks on a disc in no particular order. This func-
tion continues automatically until it is cancelled.
2. Touch the [SCROLL] key to scroll the disc
title.
3. To scroll the track title, touch the [TRACK
TITLE] key. (SCROLL key appears in the
right side of the TRACK TITLE.)
1. Touch the [SUB MODE] key in the MENU
display to show SUB MODE.
Touch the [TRACK RANDOM] key. “TRACK
RANDOM” lights in the display, an individual
track is selected randomly and play begins.
Touch the [SCROLL] key to scroll the track
title.
4. To scroll the artist title, touch the [ARTIST
TITLE] key. (SCROLL key appears in the
right side of the ARTIST TITLE.)
2. To cancel the random play, touch the
[TRACK RANDOM] key again. “TRACK
RANDOM” goes off and normal play re-
sumes.
Note:
• If the disc/track/artist title is shorter than 10 char-
acters, the track titles begin to scroll immediately.
∗ The same operation is also available by using
the [RDM] button in the panel.
VRX835
23
VISUAL Operations
This function is available when a VTR, etc. is
connected to the visual 1 or visual 2 terminal.
∗ The visual 1 mode is not available when a DVD
changer is connected to the visual 1.
G “BRIGHT”:
Adjust the brightness of the display.
G “HUE”:
Adjust the tone of color (red is emphasized
or green is emphasized)
WARNING
G “COLOR”:
For your safety, the driver should not watch
the VTR, etc. or operate the controls while
driving. Please note that watching and op-
erating the VTR, etc. while driving are pro-
hibited by law in some countries.
Adjust the color saturation.
3. Operate the touch key to adjust a level.
G “BRIGHT”:
[–] key or [+] key
G “HUE”:
Switching to the VISUAL mode
Note:
[R] key or [G] key
• For your safety, the VRX835 has a safety function
which turns off the picture when the car is mov-
ing, so only the audio can be heard. The picture
can only be watched when the car is stopped and
the parking break is applied.
G “COLOR”:
[–] key or [+] key
4. When adjustment is made, touch the [RTN]
key to return to the ADJ MENU display.
1. Press the [FUNC] buton and select the VI-
Touch the [RTN] key again to return to the
STANDARD display.
∗ To return from the adjust a level display to the
STANDARD display, press the [ADJ] button
once again.
SUAL mode.
2. Press the [BAND] button to select the VI-
SUAL1 or VISUAL2.
Switching the VTR system between
Changing over monitor display size
∗ This function is available only when the panel is
open.
NTSC and PAL
∗ This function is enabled only when the panel is
open.
Notes:
Switch to the VTR/DVD video/DVD changer
mode you use.
• This function is not available while you are driv-
ing.
• Switch to the VTR/TV/DVD video/DVD changer
mode you see.
1. Press the [ADJ] button to switch to the ad-
justment selection display.
2. Touch the [z] key to select “VTR N/P”.
1. Press the [DISP] button to change over the
monitor display size. Each time you press
the [DISP] button, the monitor display size
changes in the following order:
Touch the [VTR N/P] key, [NTSC] key and
[PAL] key appears in the display.
3. Touch the [NTSC] key or [PAL] key to select
“NTSC” or “PAL”.
“NORMAL” ➜ “WIDE” ➜ “F. WIDE” ➜
“CINEMA” ➜ “NORMAL”
Adjusting the brightness and tone of color
G “NORMAL”: (normal display)
Notes:
There is a black area at both right and left
ends of a display. In case of normal TV
broadcasting (4:3), the image can be shown
without being cut or deformed.
• This operation is available only when the car is
stopped and the parking brake is applied.
• This function is not available when the display is
stored.
• The HUE setting can be adjusted only when the
NTSC mode is selected.
G “WIDE”: (wide mode)
The image at right and left ends in a display
elongates horizontally.
• Switch to the VTR/TV/DVD video/DVD changer
mode you see.
G “F. WIDE”: (full wide mode)
1. Press the [ADJ] button to switch to the ad-
justment selection display.
The whole image elongates horizontally.
G “CINEMA”: (cinema mode)
2. Touch the [MONI ADJ] key to display
[BRIGHT], [HUE] and [COLOR] key. Touch
the [BRIGHT], [HUE] and [COLOR] key to
adjust BRIGHT, HUE and COLOR.
The image at both top and bottom in a dis-
play disappears.
24
VRX835
VISUAL Operations
CD/MD Changer
Operations
CD/MD changer functions
When an optional CD (MD) changer is con-
nected through the CeNET cable, this unit con-
trols all CD (MD) changer functions. This unit
can control a total of 2 changers (MD and/or
CD).
Notes:
• When a normal 4:3 size image, not being a wide
one, is viewed by displaying it fully on a wide moni-
tor display in a wide mode or a full-wide mode, a
part of the peripheral image will be lacking or de-
formed. In deference to the intention of producer,
an original image can be viewed in a normal mode.
• During superimposed display, it becomes a full-
wide mode.
• In the DVD changer, when the monitor display
size is set in the CINEMA mode, a part of
playback display such as play time may not be
shown depending on the play disc.
Press the [FUNC] button and select the CD
changer mode to start play. If 2 CD (MD) chang-
ers are connected, press the [FUNC] button to
select the CD (MD) changer for play.
In this case, change the monitor display size to a
mode other than the CINEMA mode.
∗ If “NO MAG” appears in the display, insert the
magazine into the CD changer. “LOADING” ap-
pears in the display while the player loads
(checks) the magazine.
Monitoring the CCD camera
The CCD camera can be connected to this unit.
For the power supply of the camera, mount the
power box sold separately (CAA-188).
∗ If “NO DISC” appears in the display, eject the
magazine and insert discs into each slot. Then,
reinsert the magazine back into the CD changer.
∗ If “NO DISC” appears in the display, load MDs
into the MD changer.
Note:
• This function is not available when the display is
stored.
CAUTION
Switching to the Composite Screen
CD-ROM discs cannot be played in the CD
changer.
∗ The composite Screen is the image of device
connected to the CCD/M.LOCK terminal.
∗ This function is available when a navigation system,
etc. is connected to the CCD/M.LOCK terminal.
∗ This function is not available when a CCD camera
is connected to the CCD/M.LOCK terminal.
1. When the panel is open, press the [M.LOCK]
button to switch to the composite screen. At
this time, the sound from the vehicle
Pausing play
1. Press the [s] button for 1 second or
longer to pause play. “PAUSE” appears in the
display.
2. To resume play, press the [s] button for 1
second or longer again.
speakers can be heard on the mode selected
using the [FUNC] button.
∗ The same operation is also available using the
[s] key in the menu screen while in the CD/
MD changer mode.
2. When the panel is open and the composite
screen is shown, press the [M.LOCK] button
again to return to the previous screen.
∗ When the panel is open, the same operation
is also available by using the [s] button in
the panel.
Switching CONNECT(connect)
∗ This function is available when a CCD,etc. is con-
Displaying CD titles (CD)
This operation is only possible when this unit is
connected with a CD-text compatible CD
changer. When a title is longer than 10 charac-
ters, the same operation can be performed on a
CD.
nected to the CCD/M.LOCK terminal.
∗ When a navigation system is connected, set this
mode to “NAVI”.
When an external device other than a navigation
system, set this mode to “OTHERS”.
∗ The factory default setting is “OTHERS”.
1. When the panel is open, press the [ADJ] but-
ton to display the ADJUST MODE menu.
2. Touch the [z] key two times to select “CON-
NECT”.
Touch the [CONNECT] key to select “NAVI”
or “OTHERS”.
3. Press the [ADJ] button again or touch the
[RTN] key, the unit returns to the previous
mode.
VRX835
25
CD/MD Changer Operations
Switching disc titles and track titles
(MD)
This unit can display disc titles and track titles
already entered on MDs. Titles up to 256 char-
acters long can be displayed by scrolling the
titles.
Selecting a CD
When the panel is closed:
Each of the [DIRECT] buttons corresponds to a
disc loaded into the magazine.
GSelecting a disc from 1 to 6
Press the corresponding [DIRECT] button (1 to
6) to select the desired disc.
∗ Titles cannot be entered for MDs with this unit.
When the panel is closed:
GSelecting a disc from 7 to 12 (only when a
1. Press the [DISP] button to show the SUB
display. The disc title or track title is dis-
played.
12 disc CD changer is used.)
Press the corresponding [DIRECT] button (1 to
6) for 1 second or more, then select the desired
disc.
2. Each time you press and hold the [DISP] but-
ton for 1 second or longer, the display
toggles between the disc title and the track
title.
When the panel is open:
Each of the [DIRECT] keys corresponds to a
disc loaded into the magazine.
When the panel is open:
GSelecting a disc from 1 to 6
1. Touch the screen to show the menu screen
while the main screen is being shown.
Touch the [DISC SELECT] key in the display,
the [DIRECT] key (1 to 6) appears in the display.
2. Touch the [TITLE INDEX] key to show the
Touch the corresponding [DIRECT] key (1 to 6)
to select the desired disc.
title display screen.
3. Touch the disc title/track title display you
want to show in the main screen.
GSelecting a disc from 7 to 12 (Only when a
12 disc CD changer is used.)
Touch the [DISC SELECT] key again, the [DI-
RECT] key (7 to 12) appears in the display.
Scrolling titles (MD)
Note:
Touch the corresponding [DIRECT] key (7 to 12)
to select the desired disc.
• This function is enabled only when the panel is
open.
When a title is longer than 10 characters, the
same operation can be performed on a CD.
Notes:
Selecting a track
GTrack-up
• When the disc title is within 10 characters, the title
is scrolled immediately.
• If the track title is shorter than 10 characters, the
track titles does not scroll.
1. Press the right side (d) of the [SEARCH]
button to move ahead to the beginning of the
next track.
2. Each time you press the right side (d) of
the [SEARCH] button, the track advances
ahead to the beginning of the next track.
Selecting an MD
When the panel is closed:
∗ When the panel is open, the same operation
is also available by using the [d] button in the
panel.
Each of the [DIRECT] button corresponds to an
MD loaded into the MD changer.
GTrack-down
Press the [DIRECT] button (1 to 6) and select
the desired MD.
1. Press the left (a) side of the [SEARCH]
button to move back to the beginning of the
current track.
When the panel is open:
Each of the [DIRECT] key corresponds to an
2. Press the left side (a) of the [SEARCH]
button twice to move to the beginning of the
previous track.
MD loaded into the MD changer.
Touch the [DISC SELECT] key in the display,
the [DIRECT] key (1 to 6) appears in the display.
∗ When the panel is open, the same operation
is also available by using the [a] button in the
panel.
Touch the [DIRECT] key (1 to 6) and select the
desired MD.
26
VRX835
CD/MD Changer Operations
Fast-forward/Fast-backward
Disc scan play
GFast-forward
The disc scan play locates and plays the first 10
seconds of the first track on each disc in the cur-
rently selected CD (MD) changer. This function
continues automatically until it is cancelled or
the mode is changed.
Press and hold the right side (d) of the
[SEARCH] button for 1 second or longer.
∗ When the panel is open, the same operation
is also available by using the [d] button in the
panel.
∗ The disc scan play is useful when you want to se-
lect a desired CD (MD).
GFast-backward
1. Touch the [SUB MODE] key in the MENU
Press and hold the left side (a) of the
display to show SUB MODE.
[SEARCH] button for 1 second or longer.
Touch the [DISC SCAN] key to start disc
scan play.
∗ When the panel is open, the same operation
is also available by using the [a] button in the
panel.
2. Touch the [DISC SCAN] key again to cancel
disc scan play. Normal disc play continues on
the current track.
Top function (CD)
The top function plays from the first track (track
No. 1) of the disc.
∗ The same operation is also available by using
the [SCN] button for 1 second or longer in the
panel.
GWhen playing a disc 1 to 6
Press the [DIRECT] button (1 to 6) with the
same number as the CD playing.
Repeat play
The repeat play continuously plays the current
track. This function continues automatically until
it is cancelled.
GWhen playing a disc 7 to 12 (only when a
12 disc CD changer is used.)
Press the [DIRECT] button (1 to 6) with the same
number as the CD playing for 1 second or longer.
1. Touch the [SUB MODE] key in the MENU
display to show SUB MODE.
Touch the [TRACK REPEAT] key, to make
repeat play starts. “TRACK REPEAT” lights
in the display.
Top function (MD)
The top function plays from the first track (track
No. 1) of the disc.
2. To cancel repeat play, touch the [TRACK RE-
PEAT] key. “TRACK REPEAT” goes off from
the display and the unit returns to normal
play.
Press the [DIRECT] button (1 to 6) with the
same number that the MD playing.
∗ If an MD is not loaded in a slot of the MD
changer, pressing the [DIRECT] button corre-
sponding to its disc number is invalid.
∗ The same operation is also available by using
the [RPT] button in the panel.
Scan play
Disc repeat play
The scan play locates and plays the first 10 sec-
onds of each track on a disc automatically. This
function continues on the disc until it is can-
celled or the mode is changed.
After all tracks in the current disc have been
played, the disc repeat play automatically re-
plays the current disc over from the first track.
This function continues automatically until it is
cancelled.
∗ The scan play is useful when you want to select a
desired track.
1. Touch the [SUB MODE] key in the MENU
display to show SUB MODE.
1. Touch the [SUB MODE] key in the MENU
display to show SUB MODE.
Touch the [DISC REPEAT] key, disc repeat
play starts, “DISC REPEAT” light in the display.
Touch the [TRACK SCAN] key to start scan
play.
2. To cancel disc repeat play, touch the [DISC
REPEAT] key again. “DISC REPEAT” goes
off from the display and the unit returns to
normal play from the track being played.
2. Touch the [TRACK SCAN] key again to can-
cel the scan play. Current track continues to
play.
∗ The same operation is also available by using
the [RPT] button for 1 second or longer in the
panel.
∗ The same operation is also available by using
the [SCN] button in the panel.
VRX835
27
CD/MD Changer Operations
DVD Changer Operation
Random play
DVD changer functions
When an optional DVD changer is connected
through the CeNET cable.
The random play selects and plays individual
tracks on the disc in no particular order. This
function continues automatically until it is can-
celled.
In this case, this unit only provides a part of the
DVD changer functions. As for other operations
not written in this manual, operates with a remote
control unit provided with your DVD changer. Refer
to the DVD changer owners’manual for details.
1. Touch the [SUB MODE] key in the MENU
display to show SUB MODE.
When you touch the [TRACK RANDOM] key,
random play starts. “TRACK RANDOM”
lights in the display.
This unit can control a total of 2 changers (CD
or MD or DVD).
2. To cancel random play, touch the [TRACK
RANDOM] key again. “TRACK RANDOM”
goes off from the display and the unit returns
to normal play.
Press the [FUNC] button and select the DVD
changer mode to start play.
∗ If “NO MAGAZINE” appears in the display, insert
the magazine into the DVD changer.
“DISC CHECKING” appears in the display while
the player loads (checks) the magazine.
∗ The same operation is also available by using
the [RDM] button in the panel.
∗ If “NO DISC” appears in the display, eject the
magazine and insert discs into each slot.
Then, reinsert the magazine back into the DVD
changer.
Disc random play
The disc random play selects and plays indi-
vidual tracks or discs automatically in no par-
ticular order. This function continues automati-
cally until it is cancelled.
Pausing Play
1. Press and hold the [s] button for 1 second
or longer to pause play. “PAUSE” appears in
the display.
1. Touch the [SUB MODE] key in the MENU
display to show SUB MODE.
When you touch the [DISC RANDOM] key,
disc random play starts. “DISC RANDOM”
lights in the display.
2. To resume play, press the [s] button for 1
second or longer again.
∗ When the panel is open, the same operation
is also available by using the [s] button in
the panel.
2. To cancel disc random play, touch the [DISC
RANDOM] key again. “DISC RANDOM” goes
off from the display and the unit returns to
normal play from the track being played.
Slow Play (DVD video & video CD)
1. Press and hold the [s] button for 1 second
or longer then press and hold the [d] but-
ton. While the button is being pressed, slow
playback continues at the speed 1/2 times
the normal playback.
∗ The same operation is also available by using
the [RDM] button for 1 second or longer in the
panel.
∗ Slow playback cannot be performed in the
backward direction. In addition, audio cannot
be reproduced during slow playback.
Selecting a disc
1. Each of the [DIRECT]buttons corresponds to
a disc loaded into the magazine.
2. Press the corresponding [DIRECT] buttons
(1 to 6) to select the desired disc.
Switching to a next disc(Disc Up
function)
The disc up function plays from the first track
(track No1) of the next disc.
28
VRX835
DVD Changer Operation
1. Press the [BAND] button.
2. Press the [RPT] button again and repeat
playback is turned off.
2. Each time you press the [BAND] button, the
disc changes to the next disc.
Title repeat playback
This operation plays back titles recorded on the
DVD-Video repeatedly.
DVD-Video Operation
Skipping a chapter(searching)
About chapter
1. Press and hold the [RPT] button for 1 second
or longer.
2. Press the [RPT] button again and repeat
Chapter means a small segment to divide the
data area of the disc.
playback is turned off.
1. Press the [a] or [d] button during playback.
Chapters are skipped, as many as the times
the button is pressed, and playback starts.
Watching a video CD
Skipping a track (searching)
1. Press the [a] or [d] button during play-
back.
• Press the [d] button, and playback starts
from the beginning of the next chapter.
• Press the [a] button, and playback starts
from the beginning of the current chapter.
The track is skipped, and playback starts.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous chapter.
• Press the [d] button, and playback starts
from the beginning of the next track.
• Press the [a] button, and playback starts
• The unit may return to the menu screen
from the beginning of the current track.
when the [a] or [d] button is pressed.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
Fast forward and fast backward
1. Press and hold the [a] or [d] button during
playback.
∗ This operation cannot be performed on some
discs with PBC
Press and hold the button, and the playback
speed becomes 4-time faster first and then
16-time faster 3 seconds later. Release the
button, and the normal speed is restored.
Fast forward and fast backward
1. Press and hold the [a] button or [d] button
during playback.
Press and hold the button, and the playback
speed becomes 4-time faster first and then
Notes:
• No audio is reproduced during fast forward
and fast rewind operation.
16-time faster 3 seconds later. Release the
button, and the normal speed is restored.
Notes:
• No audio is reproduced during fast forward
and fast rewind operation.
• The fast forward and fast rewind speed may
differ depending on the disc.
• The menu screen may appear when the button
is pressed.
• The unit may return to the menu screen when
the button is pressed.
Scan playback
Scans and plays back all chapters recorded on
the DVD-Video, the first 10 seconds for each.
Scan playback
This operation plays back all tracks on the disc,
the first 10 seconds for each.
1. Press the [SCN] button.
2. Press the [SCN] button again and scan play-
1. Press the [SCN] button.
back is turned off.
2. Press the [SCN] button again and scan play-
back is turned off.
Chapter repeat playback
This operation plays back chapters recorded on
the DVD-Video repeatedly.
∗ If you are playing a disc with PBC and the
PBC function is engaged, this operation
cannot be performed.
1. Press the [RPT] button.
VRX835
29
DVD Changer Operation
Repeat playback
This operation plays back one track recorded on
the video CD repeatedly.
Track repeat playback
This operation plays back one track recorded on
the CD repeatedly.
1. Press the [RPT] button.
1. Press the [RPT] button.
2. Press the [RPT] button again and repeat
2. Press the [RPT] button again and repeat
playback is turned off.
playback is turned off.
∗ If you are playing a disc with PBC and the
PBC function is engaged, this operation
cannot be performed.
Disc repeat playback
This operation plays back all tracks on the disc
repeatedly (with music CDs only).
Random playback
This operation plays back all track on the disc in
no particular order.
1. Press and hold the [RPT] button for 1 second
or longer.
2. Press the [RPT] button again and repeat
1. Press the [RDM] button.
playback is turned off.
2. Press the [RDM] button again and random
playback is turned off.
Random playback
This operation plays back all track on the disc in
no particular order.
∗ If you are playing a disc with PBC and the
PBC function is engaged, this operation
cannot be performed.
1. Press the [RDM] button.
2. Press the [RDM] button again and random
Listening to a CD
playback is turned off.
Skipping a track (searching)
1. Press the [a] or [d] button during playback.
Listening to an MP3
The tracks are skipped, as many as the
times the button is pressed, and playback
starts.
Skipping a track (searching)
1. Press the [a] or [d] button during play-
back.
• Press the [d] button, and playback starts
from the beginning of the next track.
The tracks are skipped, as many as the
times the button is pressed, and playback
starts.
• Press the [a] button, and playback starts
from the beginning of the current track.
• Press the [d] button, and playback starts
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
from the beginning of the next track.
• Press the [a] button, and playback starts
from the beginning of the current track.
When this button is pressed again within
about 2 seconds, playback starts from the
beginning of the previous track.
Fast forward and fast backward
1. Press and hold the [a] or [d] button during
playback.
∗ This operation skips the track over the folder.
Press and hold the button, and the playback
speed becomes 4-time faster first and then
8-time faster 3 seconds later. Release the
button, and the normal speed is restored.
Fast forward and fast backward
1. Press and hold the [a] or [d] button during
playback.
Press and hold the button, and the playback
speed becomes 4-time faster first and then
8-time faster 3 seconds later. Release the
button, and the normal speed is restored.
Scan playback
This operation plays back all tracks on the disc,
the first 10 seconds for each.
1. Press the [SCN] button.
2. Press the [SCN] button again and scan play-
back is turned off.
30
VRX835
DVD Changer Operation
TV Operations
Track scan playback
TV functions
When an optional TV tuner is connected through
the CeNET cable, this unit controls all TV tuner
functions. To watch TV requires a TV tuner.
This operation plays back all files recorded on
the disc, about 10 seconds for each.
1. Press the [SCN] button.
2. Press the [SCN] button again and scan play-
WARNING
back is turned off.
For your safety, the driver should not
watch the TV or operate the controls while
driving. Please note that watching and op-
erating the TV while driving are prohibited
by law in some countries.
Folder scan playback
This operation plays back the first files of all
folders on the MP3 disc, about 10 seconds for
each.
Watching TV
Note:
1. Press and hold the [SCN] buttonfor 1 second
or longer.
• For your safety, the VRX835 has a safety function
which turns off the picture when the car is mov-
ing, so only the audio can be heard. The picture
can only be watched when the car is stopped and
the parking break is applied.
2. Press the [SCN] button again and scan play-
back is turned off.
Track repeat playback
This operation plays back the file currently being
played back repeatedly.
1. Press the [FUNC] button and select the TV
mode.
1. Press the [RPT] button.
2. Press the [BAND] button to select the de-
sired TV band (TV1 or TV2). Each time the
button is pressed, the input selection toggles
between TV1 and TV2.
2. Press the [RPT] button again and repeat
playback is turned off.
Folder repeat playback
This operation plays back files in an MP3 folder
repeatedly..
3. Press the right (d) or left (a) side of the
[SEARCH] button to tune in the desired TV
station.
1. Press and hold the [RPT] button for 1 second
or longer.
Watching a video
2. Press the [RPT] button again and repeat
The TV tuner has a VTR input terminal to which
1 external device can be connected. Connect a
12V video cassette player (VCP) or video cas-
sette recorder (VCR) to the TV tuner input termi-
nal.
playback is turned off.
Track random playback
This operation plays the file in the folder in ran-
dom order.
1. In the TV mode, touch the [EXTRA SELECT]
key in the MENU display to select the [VTR]
key.
1. Press the [RDM] button.
2. Press the [RDM] button again and random
2. To return to the TV broadcast, touch the [EX-
TRA SELECT] key in the MENU display to
select the [TELEVISION] key.
playback is turned off.
Folder random playback
This operation plays back tracks recorded on
the disc in no particular order.
Tuning
There are 3 types of tuning mode available,
seek tuning, manual tuning and preset tuning.
1. Press and hold the [RDM] button for 1 sec-
ond or longer.
2. Press the [RDM] button again and random
playback is turned off.
VRX835
31
TV Operations
Seek tuning
Recalling a preset station
A total of 12 TV stations can be stored (6-TV1
and 6-TV2). This allows you to select your favor-
ite TV stations and store them in memory for
later recall.
1. Press the [BAND] button and select the de-
sired TV band (TV1 or TV2).
∗ If “MANU” is lit in the display (or when the
panel is closed, if the indicator “
” is not
lit), press and hold the [BAND] button for 1
second or longer. “MANU” in the display goes
off (or when the panel is closed, the indicator
1. Press the [BAND] button and select the de-
sired TV band. (TV1 or TV2)
2. To recall a stored TV station, press the de-
“
” lights) and seek tuning is now
sired [DIRECT] button to select that station.
available.
∗ Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
station into the preset memory.
2. Press the right (d) or left (a) side of the
[SEARCH] button to automatically seek a
station. Press the right (d) side of the
[SEARCH] button to automatically tune up
the frequency band to the next available TV
station; press the left side to automatically
tune down.
∗ When the panel is open, the same operation
is also available by using the [a] and [d]
button in the panel.
Manual memory
1. Select the desired station with seek tuning,
manual tuning or preset tuning.
Manual tuning
There are 2 ways available: Quick tuning and
step tuning. When you are in the step tuning
mode, the frequency changes one step at a
time. In quick tuning mode, you can quickly tune
the desired frequency.
2. Press and hold one of the [DIRECT] buttons
for 2 seconds or longer to store the current
station to that preset memory.
Auto store
Auto store selects 6 TV stations automatically
and stores each one into a preset memory.
1. Press the [BAND] button and select the de-
sired band. (TV1 or TV2)
∗ If “MANU” is not lit in the display (or when the
panel is closed, if the indicator “
” is lit),
If there are not 6 stations with good reception,
stations previously stored in memory remain
and only the strong stations are stored into
memory.
press and hold the [BAND] button for 1
second or longer. “MANU” appears in the
display (or when the panel is closed, the
indicator “
” goes off) and manual tuning
1. Press the [BAND] button and select the de-
is now available.
sired TV band. (TV1 or TV2)
2. Tune into a station.
2. Touch the [SUB MODE] key in the MENU
display, the [AUTO STORE] key appears in
the display.
GQuick tuning:
Press and hold the right (d) or left (a) side of
the [SEARCH] button for 1 second or longer to
tune in a station.
Touch and hold the [AUTO STORE] key for 2
seconds or longer. The stations with good re-
ception are stored automatically to the preset
channels.
∗ The same operation is also available by using
the [SCN] button for 2 seconds or longer in the
panel.
GStep tuning:
Press the right (d) or left (a) side of the
[SEARCH] button to manually tune in a station.
Note:
•
Manual tuning is cancelled if you do not operate
the unit for 7 seconds longer. (∗Only when con-
necting the TTX7503Z or TTX7504Z with this unit)
Preset scan
Preset scan allows the user to view each preset
position before it automatically advances to the
next preset. This function is useful for searching
for desired TV station in memory.
32
VRX835
TV Operations
Other Functions
1. Touch the [SUB MODE] key in the MENU
display, the [PRESET SCAN] key appears in
the display.
Always turning on the button
illumination on the operation panel
Notes:
Touch the [PRESET SCAN] key to start pre-
set scan.
• The following operation is enabled when the
panel is open.
• Doing this operation turns on and off the
illunination only for the buttons of VoL [+] and [–],
[TILT], and [OPEN].
The button illumination on the operation panel
when the display is turned upward, can be
switched between “ON” and “OFF”.
2. When the desired channel is received, touch
the [PRESET SCAN] key again.
∗ The same operation is also available by using
the [SCN] button in the panel.
Setting the TV diver
G“OFF”: Button illumination on the operation
panel turns on for 5 seconds;
∗ This function is enabled only when the panel is
open.
G“ON”: Button illumination is always on when
the power is turned on;
∗ Normally use the TV diver with the “ON” position.
You can change the reception setting for the TV
antenna connected to the TV tuner.
1. When the panel is open, press the [ADJ] button
to show the adjustment selection display.
1. Press the [ADJ] button to switch to the ad-
2. Touch the [UPPER ILLUMI] key to select
justment selection display.
“ON” or “OFF”.
2. Touch the [z] key to select “TV DIVER”.
3. Touch the [ON] or [OFF] key for setting.
Touch the [TV DIVER] key to display [ON]/
[OFF] key.
4. Press the [ADJ] button to return to the previ-
ous mode.
∗ To set “ON” again, switch “OFF” to “ON”
manually.
3. Touch the [ON] key or [OFF] key to set the
selected reception setting.
G ON:
Sets reception emphasizing the visual.
G OFF:
Entering titles
Titles up to 10 characters long can be stored in
memory and displayed for Radio stations, TV
stations and CDs. The numbers of titles that can
be entered for each mode are as follows.
Sets the diver setting to OFF.
4. Press the [ADJ] button to return to the previ-
ous mode.
Number of titles
30 titles
Mode
Setting the TV area
TUNER mode
TV mode
CD mode
∗ This function is enabled only when the panel is
15 titles
open.
50 titles
When you select the TV area (TV reception
area), the TV tuner area setting changes.
CD changer mode
CDC655z connected
CDZ625, CDC655Tz
connected
Number of titles
1. Press the [ADJ] button to switch to the ad-
60 titles
justment selection display.
2. Touch the [z] key to select “TV AREA”.
Touch the [TV AREA] key to display a list of
country name.
100 titles
50 titles
CDC1255z connected
3. Touch the [COUNTRY NAME] key to select
∗ You cannot enter titles with the unit in Seek, Pre-
set Scan, Auto store (TUNER, TV) mode. Cancel
each of those operations before entering titles.
a desired country.
4. When the setting is finished, touch the [RTN]
key in the TV AREA selection display to
return to the STANDARD display.
1. Press the [FUNC] button to select the mode
you want to enter a title (TUNER, CD, CD
changer or TV).
∗ To return from the TV AREA select display to
the STANDARD display, press the [ADJ]
button once again.
2. Select and play a CD or a CD in the CD
changer or tune in to a Radio station or a TV
station for which you want to enter the title.
VRX835
33
Other Functions
3. Touch the [TITLE INPUT] key in the MENU
Adjusting the dimmer level
display.
You can adjust the reduced illumination level of
the dimmer. When driving at night with the inside
of the car, the auto dimmer function can reduce
the display illumination linked “to the illumina-
tion power supply of the car” in this unit in or-
der to prevent glare from the display.
Touch the [INPUT] key in the USER TITLE
display, the display switches to the title input
mode display.
4. Touch the characters, symbols, etc. shown in
the display to input titles.
G The factory default:
“←, →” : Centering
When the car light is off: Brightest setting
When the car light is on: Medium brightness
“BS”
: Backspace
: Space
“
”
1. When the panel is open, press the [ADJ] but-
ton to display the adjustment selection dis-
play.
“MEMO” : Memory
“z(w)” : Scroll
Note:
• Up to 10 characters can be input.
• To switch the character types, touch the scroll key
(z) at the lower left of the display.
5. Repeat the step 4 to enter the complete title.
2. Touch the [DIMMER LEVEL] key to adjust
the dimmer level.
3. Touch the [+] or [–] key to adjust.
4. Press the [ADJ] button again or touch the
[RTN] key two times.
6. Touch the [MEMO] key for 2 seconds or
longer to store the title into memory and can-
cel title input mode.
The unit returns to the previous mode.
Setting the button illumination
Title list play
∗ The factory default setting is “GREEN” (green).
You can display a list of titles, then select the
disc or broadcast station to listen to from that
list.
1. When the panel is open, press the [ADJ] but-
ton to select the adjustment mode.
2. Touch the [KEY ILLUMI] key to select “RED”
∗ You can not display a title list with the unit in Seek,
Preset Scan, Auto store (Tuner, TV) mode. Cancel
those operation modes before to display a title list.
(red) or “GREEN” (green).
3. Touch the [RED] or [GREEN] key to select a
desired mode and set it.
1. With the unit in radio, CD/MD changer, TV
mode, touch the [P. CH SELECT], [DISC SE-
LECT] key. A title list is displayed. The follow-
ing functions can be carried out in a title list
display.
4. Press the [ADJ] button again or touch the
[RTN] key. The unit returns to the previous
mode.
GTUNER: A title of a station stored in the
presets 1 to 6 or frequency is displayed;
Setting the beep
∗ The sound heard when you make operations is
called “beep”. The unit can be set up so that it
does not produce this beep sound.
GCD/MD changer: DISC titles for discs 1 to
6 are displayed (By changing over a dis-
play page in case of 12-CD changer, disc 7
to 12 can be displayed). When there is not
any disc in a changer, ”NO DISC” is dis-
played.
∗ The factory default is “BEEP ON”.
1. When the panel is open, press the [ADJ] but-
ton to select the adjustment mode.
2. Touch the [z] key two times to select
GTV: A title of a channel stored in the presets
1 to 6 or a channel number is displayed.
“BEEP”.
Touch the [BEEP] key to select “ON” and
2. Touch the [DIRECT] key (1 to 6) to select
one of the items 1 to 6 and reproduce the se-
lected broadcast station or disc.
“OFF”.
3. Touch the [ON] or [OFF] key to select a de-
sired mode and set it.
∗ In case of 12-CD changer, touch the [DISC
SELECT] key to change over to a list display
of discs 7 to 12.
4. Press the [ADJ] button again or touch the
[RTN] key, The unit returns to the previous
mode.
3. Touch the [RTN] key again to return to the
STANDARD display.
34
VRX835
Other Functions
DSP operations
Setting the sprite pattern speed
DSP control function
If the DSP (DPH910), sold separately, is con-
nected to this unit using the CeNET cable, all
the functions of the DSP can be controlled.
∗ The factory default setting is “MID” (mid).
1. When the panel is open, press the [ADJ] but-
ton to select the adjustment mode.
∗ DSP control can all be operated only when the
panel is open.
2. Touch the [ANA SENS] key to select “HIGH”
(high) or “MID” (mid) or “LOW” (low).
3. Touch the “HIGH” (high) or “MID” (mid) or
“LOW” (low) key to select a desired mode
and set it.
DSP functions
There are 2 modes available in DPH910, stan-
dard mode and professional mode. Choose one
of them and adjust the sound field and the
sound quality.
4. Press the [ADJ] button again or touch the
[RTN] key. The unit returns to the previous
mode.
GFunctions common to each mode:
Such as auto loudness, subwoofer etc.
GStandard mode:
Clock Adjustment
1. When the panel is open, press the [ADJ] but-
ton to select the adjustment mode.
Adjustment using the graphic equalizer function
and the DSF (Digital Sound Field) function.
2. Touch the [z] key to select “CLOCK”.
GProfessional mode:
Touch the [CLOCK] key to adjust the time.
Adjustment using the VSE (Virtual Space En-
hancer) function and the parametric equalizer
function.
3. Touch the [w],[z],[a.m] or [p.m] key to ad-
just the time.
∗ The time is displayed in 12-hour format.
∗ When the standard mode is selected, adjustment for
the professional mode cannot be made. On the con-
trary, when the professional mode is selected, ad-
justment for the standard mode cannot be made.
4. Press the [ADJ] button again or touch the
[RTN] key two times. The unit returns to the
previous mode.
∗ For details on functions of each mode, refer to the
owner’s manual supplied with the DPH910.
Triggered audio mute for cellular
telepones
This unit requires special wiring to mute the au-
dio signal automatically when a cellular tele-
phone rings in the car.
∗ Hereafter the graphic equalizer is referred to as a
G.EQ, referred to as VSE and the parametric
equalizer referred to as P.EQ.
Operations common to each mode
Output adjustment of auto loudness,
subwoofer and playback band
1. Press the [ADJ] button to switch to the ad-
justment selection display.
∗ This function is not compatible wiht all cellular
telepones Contact your local authorized Clarion
dealer for information on proper installation and
compatibility.
2. Touch the [z] key two times to select
“SOUND”.
Touch the [SOUND] key to change into the
Sound adjustment display.
In the Sound adjustment display “AUTO
LOUD”, “W-OUT”, “W-LFP”, “HPF”, “TEST-T”
are listed.
Touch the [LIST] key to select an item to be
adjusted.
3. To make an adjustment on:
G Auto loudness adjustment
Touch the [w] or [z] key to adjust an auto
loudness level (0 to 10).
VRX835
35
DSP operations
G Woofer out adjustment
Entering titles
You can give a title to the user memory of the
G.EQ, DSF, VSE and P.EQ that you have ad-
justed yourself.
Select woofer output out of “STEREO”,
“MONO”, or “OFF”.
Touch the select a desire item key to set it.
1. Press the [A-M] button to select the adjust-
G Woofer LPF adjustment
ment mode in which you want to give a title.
Select woofer LPF slope out of “50Hz”,
“80Hz”, “120Hz”.
2. Touch the [USER] key to select the “USER”.
3. Touch the [USER TITLE] key to select the
user memory to which you want to give a
title.
Touch the select a desire item key to set it.
G HPF adjustment
Select HPF slope out of “50Hz”, “80Hz”,
“120Hz”, or “OFF”.
4. Touch the [TITLE] key in the USER TITLE
display, the display switches to the title input
mode display.
Touch the select a desire item key to set it.
G Test Tone Output
5. Touch the characters, symbols, etc. shown in
the display to enter titles.
Select Test Tone Output
Touch the select a desire item key to produce
a test tone.
“←, →” : Centering
“BS”
: Backspace
: Space
4. After adjustment (setting), touch the [RTN]
key to return to the adjustment selection dis-
play.
“
”
“MEMO” : Memory
“z(w)” : Scroll
Note:
• Up to 8 characters can be input.
5. Press the [ADJ] button again or touch the
[RTN] key to return to the STANDARD display.
• To switch the character types, touch the scroll key
(w) at the lower left of the display.
6. Repeat the step 5 to input the title.
Selecting the Standard mode or the
professional mode
∗ The factory default setting is “STANDARD”.
7. Touch the [MEMO] key for 2 seconds or
longer to store the title into memory.
1. Press the [ADJ] button to switch to the ad-
justment selection display.
8. Press the [A-M] button again. The unit re-
turns to the previous mode.
2. Touch the [z] key two times to select “AC
PROCESSOR”.
Touch the [AC PROCESSOR] key to select
“PRO” and “STANDARD”.
Standard mode/Setting the
listening position
3. Touch the [PRO] or [STANDARD] to select a
desired mode and to set the mode thus se-
lected.
Selection of listening position
1. Press the [A-M] button to show the AUDIO-
MODE display.
4. After setting, press the [ADJ] button again to
return to the STANDARD display.
2. Touch the [z] key to select “POSI. SELECT”.
Touch the [POSI. SELECT] key to set the lis-
tening position type.
Woofer level adjustment
You can adjust an output sound level of
subwoofer.
There are FULL SEAT, FRONT R (only right
seat), FRONT L (only left seat), FRONT (only
front seats), REAR (only rear seats) and
PASS available for the listening position types.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [WOOFER VOL] key to show the
∗ The factory default setting is “FULL SEAT”.
woofer level adjusting display.
3. Touch the [w] or [z] key to adjust the level
Detail adjustment of listening
(0 to 14)
position
4. After adjustment, touch the [RTN] key to re-
1. Press the [A-M] button to show the AUDIO-
turn to the STANDARD display.
MODE display.
36
VRX835
DSP operations
∗ After selecting the G.EQ pattern, touch the
[MEMO] key to copy the selected pattern to
the USER pattern.
2. Touch the [z] key to select “POSI. DETAIL”.
Touch the [POSI. DETAIL] key to show Posi-
tion Detail adjusting display.
∗ Touch the [EDIT] key to show G.EQ adjusting
display, in which the properties of currently
selected pattern can be adjusted.
3. Touch the [w] or [z] key to adjust to a de-
sired fader.
Adjusting range of the fader: front 9/rear 9
∗ By pressing the [BAND] button in BASIC
pattern selecting display or USER pattern
selection/memory display you can switch
between the two patterns, BASIC and USER.
4. Touch the [Î] or [Å] key to adjust to a de-
sired balance.
Adjusting range of the balance: left 9/right 9
4. After the selecting, press the [A-M] button
again or touch the [RTN] key two times to re-
turn to the STANDARD display.
5. When the adjustment is finished, press the [A-
M] button again or touch the [RTN] key two
times to return to the STANDARD display.
Setting and storing G.EQ Properties/
Memory into USER Pattern
Standard mode/G.EQ operations
1. Repeat the steps 1 and 2 of the previous proce-
dure (Calling G.EQ BASIC pattern/USER pat-
tern) to show BASIC pattern selecting display
or USER pattern selection/memory display.
Note:
• The adjustment made in standard mode is not re-
flected in the adjustment in professional mode.
Respectively, the adjustment made in profes-
sional mode is not reflected in the adjustment in
standard mode.
2. Touch the [EDIT] key to show the G.EQ ad-
justing display.
3. When some frequency to be adjusted is se-
lected by touching the [Î] key or [Å] key (or
the frequency key) in the G.EQ adjusting dis-
play, a gain setting value at the selected fre-
quency is displayed.
G.EQ effect ON/OFF
∗ The factory default setting is “ON”.
1. Press the [A-M] button to show the AUDIO-
MODE display.
There are “50Hz”, “100Hz”, “200Hz”,
“400Hz”, “1kHz”, “3kHz” and “12kHz” avail-
able for the adjustment frequency.
2. Touch the [G.EQ ON/OFF] key to select “on”
and “off”.
3. Each time the [ON/OFF] key is touched, the
4. Touch the [w] or [z] key to adjust the G.EQ
GAIN. The adjustment range is from -12 dB
to +12 dB.
on and off statuses are switched alternately.
4. After the setting, press the [A-M] button
again or touch the [RTN] key to return to the
STANDARD display.
5. After making adjustments to a desired pat-
tern by repeating the operations of items 3
and 4, touch the [RTN] key to change over to
the BASIC/USER pattern selection/memory
display.
Note:
• If the G.EQ effect is set to OFF, the adjustment
made in “G.EQ operations” is not reflected in the
music source.
6. Press and hold one of [DIRECT] buttons for
2 seconds or longer to store the adjusted
G.EQ pattern to be USER memory.
Calling G.EQ BASIC Pattern/USER
Pattern
7. To set a title of the stored USER pattern,
touch the [TITLE] key to change into the
[TITLE INPUT] key.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [G.EQ BASIC] and [G.EQ USER]
key to show BASIC pattern selecting display
or USER pattern selection/memory display.
∗ For title inputting method, refer to the section
“Entering titles”.
8. Press the [A-M] button to change into the
3. In the pattern selecting display, touch the one
of pattern key and called the desired G.EQ
pattern.
STANDARD display.
In this display, pressing the No. button in cor-
respondence to the [DIRECT] key can also
call the G.EQ pattern.
VRX835
37
DSP operations
Setting and storing DSF Properties/
Standard mode/DSF operations
Memory into USER Pattern
1. Repeat the steps 1 and 2 of the previous
procedure (Calling DSF BASIC Pattern/
USER Pattern) to show BASIC pattern se-
lecting display or USER pattern selection/
memory display.
DSF effect ON/OFF
∗ The factory default setting is “ON”.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [DSF ON/OFF] key to select “on”
and “off”.
2. Touch the [EDIT] key to show the DSF ad-
justing display.
3. Each time the [ON/OFF] key is touched, the
on and off statuses are switched alternately.
3. Select an item to be adjusted by touching
[ITEM] key in the DSF adjusting display.
4. After the setting, press the [A-M] button
again or touch the [RTN] key to return to the
STANDARD display.
There are “EFFECT”, “DELAY”, “REAR MIX”,
“REVERB TIME” (ROOM SIZE) and “HIGH”
(LIVENESS).
Note:
• If the DSF effect is set to OFF, the adjustment
made in “DSF operations” is not reflected in the
music source.
4. Touch the [w] or [z] key to set each adjust-
ing value.
5. After making adjustments to a desired pat-
tern by repeating the operations of items 3
and 4, touch the [RTN] key to change over to
the BASIC/USER patterns selection/memory
display.
Calling DSF BASIC Pattern/USER
Pattern
1. Press the [A-M] button to show the AUDIO-
6. Press and hold one of [DIRECT] button for 2
seconds or longer to store the adjusted DSF
pattern to the USER memory.
MODE display.
2. Touch the [z] key to select DSF mode.
Touch the [DSF BASIC1], [DSF BASIC2]
and [DSF USER] key to show BASIC pattern
selecting display or USER pattern selection/
memory display.
7. To set a title of the stored USER pattern,
touch the [TITLE] key to change into the
[TITLE INPUT] key.
∗ For title inputting method, refer to the section
3. In the pattern selecting display, touch the one
of pattern key to call corresponding DSF
mode.
“Entering titles”.
8. Press the [A-M] button to change into the
STANDARD display.
In this display, pressing the No. button in cor-
respondence to the [DIRECT] key can also
call the DSF mode.
∗ After selecting the DSF mode, touch the
[MEMO] key to copy the selected pattern to
the USER pattern.
Professional mode/VSE
operations
Note:
∗ Touch the [EDIT] key to show DSF adjusting
display, in which the properties of currently
selected pattern can be adjusted.
• The adjustment made in professional mode is not
reflected in the adjustment in standard mode. On
the contrary, the adjustment made in standard
mode is not reflected in the adjustment in profes-
sional mode.
∗ By pressing the [BAND] button in BASIC
pattern selecting display or USER pattern
selection/memory display you can switch
between the two patterns, BASIC and USER.
VSE effect ON/OFF
4. After the setting, press the [A-M] button
again or touch the [RTN] key two times to re-
turn to the STANDARD display.
∗ The factory default setting is “ON”.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [VSE ON/OFF] key to select “on”
and “off”.
3. Each time the [ON/OFF] key is touched, the
on and off statuses are switched alternately.
38
VRX835
DSP operations
4. After the setting, press the [A-M] button
again or touch the [RTN] key to return to the
STANDARD display.
G“CAR WIDTH”
Compensates for the width of the car’s inte-
rior (lateral direction).
Note:
G“DIFFUSE”
• If the VSE effect is set to OFF, the adjustment
made in “VSE operations” is not reflected in the
music source.
Compensates for special impression.
4. Touch the [w] or [z] key to make the ad-
justment.
The adjustment range is to 1 to 10 for each
time.
Calling VSE BASIC Pattern/USER
Pattern
5. After making adjustments to a desired pat-
tern by repeating the steps 3 and 4, touch
the [RTN] key to change over to the BASIC/
USER pattern selection/memory display.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [VSE BASIC] and [VSE USER]
key to show BASIC pattern selecting display
or USER pattern selection/memory display.
6. Press and hold one of [DIRECT] button for 2
seconds or longer to store the adjusted VSE
pattern to the USER memory.
3. In the pattern selecting display, touch the one
of pattern key to call corresponding VSE pat-
tern.
7. To set a title of the stored USER pattern,
touch the [TITLE] key to change into the
[TITLE INPUT] key.
In this display, pressing the No. button in cor-
responding to the [DIRECT] key can also call
the VSE pattern.
∗ After selecting the VSE pattern, touch the
[MEMO] key to copy the selected pattern to
the USER pattern.
∗ For title inputting method, refer to the section
“Entering titles”.
8. Press the [A-M] button to change into the
STANDARD display.
∗ Touch the [EDIT] key to show VSE adjusting
display, in which the properties of currently
selected pattern can be adjusted.
Professional mode/P.EQ
operations
∗ By pressing the [BAND] button in BASIC
pattern selecting display or USER pattern
selection/memory display you can switch
between the two patterns, BASIC and USER.
P.EQ effect ON/OFF
∗ The factory default setting is “ON”.
4. After the selecting, press the [A-M] button
again or touch the [RTN] key two times to re-
turn to the STANDARD display.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [P.EQ ON/OFF] key to select “on”
and “off”.
3. Each time the [ON/OFF] key is touched, the
Setting and storing VSE Properties/
on and off statuses are switched alternately.
Memory into USER Pattern
1. Repeat the steps 1 and 2 of the previous
procedure (Calling VSE BASIC Pattern/
USER pattern) to show BASIC pattern se-
lecting display or USER pattern selection/
memory display.
4. After the setting, press the [A-M] button
again or touch the [RTN] key to return to the
STANDARD display.
Note:
• If the P.EQ effect is set to OFF, the adjustment
made in “P.EQ operations” is not reflected in the
music source.
2. Touch the [EDIT] key to show the VSE ad-
justing display.
3. Select an item to be adjusted by touching
[ITEM] key in the VSE adjusting display.
The VSE adjustment contents are as follows:
G“CAR LENGTH”
Compensates for the length of the car‘s inte-
rior (longitudinal direction).
VRX835
39
DSP operations
G“GAIN”
Calling P.EQ BASIC Pattern/USER
Adjust the gain (output level) in the range of -
12 dB to +12 dB. (1 dB step, 25 points)
Pattern
1. Press the [A-M] button to show the AUDIO-
G“Q”
MODE display.
Set the sharpness of the Q-curve to one of
the parameters: 1, 3, 5, 7 and 20.
2. Touch the [z] key to select “P.EQ BASIC”
and “P.EQ USER” mode.
5. After making adjustments to a desired pat-
tern by repeating the operations of items 3
and 4, touch the [RTN] key to change over to
the BASIC/USER pattern selection/memory
display.
Touch the [P.EQ BASIC] and [P.EQ USER]
key to show BASIC pattern selecting display
or USER pattern selection/memory display.
3. In the pattern selecting display, touch the one
of pattern key to call corresponding P.EQ
pattern. In this display, pressing the No. but-
ton in corresponding to the [DIRECT] key
can also call the P.EQ pattern.
6. Press and hold one of [DIRECT] button for 2
seconds or longer to store the adjusted P.EQ
pattern to the USER memory.
∗ After selecting the P.EQ Pattern, touch the
[MEMO] key to copy the select pattern to the
USER pattern.
7. To set a title of the stored USER pattern,
touch the [TITLE] key to change into the
[TITLE INPUT] key.
∗ Touch the [EDIT] key to show P.EQ adjusting
display, in which the properties of currently
selected pattern can be adjusted.
∗ For title inputting method, refer to the section
“Entering titles”.
8. Press the [A-M] button to change into the
∗ By pressing the [BAND] button in BASIC
pattern selecting display or USER pattern
selection/memory display you can switch
between the two patterns, BASIC and USER.
STANDARD display.
4. After the selecting, press the [A-M] button
again or touch the [RTN] key two times to re-
turn to the STANDARD display.
Setting and storing P.EQ Properties/
Memory into USER Pattern
1. In the Basic adjustment display or in the
User setting display, press the [A-M] button
to show the AUDIO-MODE display.
2. Touch the [EDIT] key to show the P.EQ ad-
justing display.
3. Select an item to be adjusted by touching
[ITEM] key in the P.EQ adjusting display.
4. Touch the [ITEM] key to set each adjusting
value.
The P.EQ adjustment contents are as fol-
lows:
G“FRONT/REAR”
G“BAND”
Select the channel to be compensated (front
or rear).
G“FREQUENCY”
Select the center frequency that you want to
compensate from the range of 20 Hz to 20
kHz. (1/3 octave step, 31 points)
40
VRX835
DVD Deck (video) Operations
DVD deck (video) functions
When an optional DVD deck (DVS9755z) is
connected through the CeNET cable.
Center level adjustment
You can adjust an output sound level of center
speaker.
In this case, this unit only provides a part of the
DVD deck functions. As for other operations not
written in this manual, operates with a remote
control unit provided with your DVD deck. Refer to
the DVD deck owners’ manual for details.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [CENTER VOL] key to show the
center level adjusting display.
3. Touch the [w] or [z] key to adjust the level
Press the [FUNC] button and select the DVD
deck (video) mode to start play.
∗ If “NO DISC” appears in the display, insert a disc
into the DVD deck.
(0 to -6)
4. After adjustment, touch the [RTN] key to re-
turn to the STANDARD display.
Adjusting the balance and fader
1. Press the [A-M] button to change into the
AUDIO-MODE display.
Play/Still
Pressing and holding the [s] button for about
1 second or longer switches to the desired
mode (play, still (pause)).
2. Touch the [BAL/FAD] key when the AUDIO-
MODE screen is being displayed to show the
BALANCE/FADER adjustment screen.
Each time the button is pressed and held for
about 1 second or longer, the mode is switched
sequentially.
3. Touch the [Î] or [Å] key to adjust to the de-
sirable balance.
When the [d] button is kept pressed during the
still mode, slow play (1/2 play) is performed so
far as the button is pressed.
Adjusting range of the balance: left 13 to
right 13
4. Touch the [w] or [z] key to adjust to the de-
sirable fader.
Chapter up/down (FF/FB)
Adjusting range of the fader: front 12 / rear
12
Press the right side of [SEARCH] button for 1
second or shorter to increment chapters.
5. When adjustment is finished, touch the
[RTN] key on the BALANCE/FADER adjust-
ment screen to return to the AUDIO-MODE
screen.
Hold down the right side of [SEARCH] button for
1 second or longer to fast forward.
Press the left side of [SEARCH] button for 1
second or shorter to decrement chapters.
Touch the [RTN] key on the AUDIO-MODE
screen to return to the STANDARD display.
∗ To return from the BALANCE/FADER mode
display to the STANDARD display, press the
[A-M] button once again.
Hold down the left side of [SEARCH] button for
1 to fast backward.
Woofer level adjustment
You can adjust an output sound level of
subwoofer.
∗ A DVD changer can not be connected along
with this unit.
1. Press the [A-M] button to show the AUDIO-
MODE display.
2. Touch the [WOOFER VOL] key to show the
woofer level adjusting display.
3. Touch the [w] or [z] key to adjust the level
(-6 to +3)
4. After adjustment, touch the [RTN] key to re-
turn to the STANDARD display.
VRX835
41
11. IN CASE OF DIFFICULTY
Problem
Cause
Measure
Power does not
turn on.
Fuse is blown.
Replace with a fuse of the same amperage. If the
fuse blows again, consult your store of purchase.
(No sound is pro-
duced.)
Incorrect wiring.
Consult your store of purchase.
Nothing happens The microprocessor has
Turn off the power, then press the [RELEASE] lever
when buttons are malfunctioned due to noise, and remove the DCP.
pressed.
etc.
Press the reset button for about 2 seconds with a
thin rod.
Display is not ac-
curate.
Tuner Amp Unit
Main Unit
The Reset button
The Reset button
The remote con- Direct rays of the sun fall on When direct rays of the sun fall on the light-receptive
troller does not
work.
the light-receptive part of the part of the remote controller, it may not work.
remote controller.
The batteries of the remote
controller unit are dead or
there is no battery in the re-
mote controller unit.
Check the batteries of the remote controller unit.
Compact disc
cannot be
loaded.
Another compact disc is al-
ready loaded.
Eject the compact disc before loading the new one.
There is a disc other than a The foreign matter is forcibly ejected.
CD or foreign matter already
in place.
Sound skips or is Compact disc is dirty.
noisy.
Clean the compact disc with a soft cloth.
Compact disc is heavily
scratched or warped.
Replace with a compact disc with no scratches.
Sound is bad di- Water droplets may form on Let dry for about 1 hour with the power on.
rectly after power the internal lens when the
is turned on.
car is parked in a humid
place.
42
VRX835
Problem
Cause
Measure
The image is not The parking brake is not
Check that the parking brake is applied.
displayed.
pulled.
The display is
dark.
The brightness control is too Adjust the brightness properly.
low.
The operating condition is
not good.
The temperature inside the vehicle may be 0˚C or
less. Set to an appropriate temperature (25˚C or so)
and check it again.
The headlight of the vehicle The display is made dark at night to prevent the
is lit.
glare (When the headlight of the vehicle is lit in the
daytime, the display gets dark).
The color of the
The color is not adjusted ad- Check that COL and HUE are adjusted properly.
display is light or equately.
a shade of color
is not good.
When the VTR is Improper NTSC/PAL setting Set the NTSC/PAL properly according to the VTR.
connected, the
image is dis-
turbed.
When the TV
Bad receiving condition
A radio wave may not reach sufficiently due to ob-
struction of mountains or buildings. Check it again at
a place where a radio wave can be received prop-
erly.
tuner is con-
nected, the im-
age gets unclear.
The TV tuner has Bad receiving condition
a double or triple
image.
It may be under the influence of radio wave reflected
by mountains or buildings. Check it again after
changing place or direction.
The TV tuner has Presence of jamming
spots or stripes in
the image.
It may be under the influence from automobiles,
streetcar, power cable, neon sign, and so forth.
Check it again after changing place.
There are red,
green, and blue
points in the dis-
play.
This is not a failure, but a phenomenon peculiar to a
liquid crystal panel (The LCD panel is produced ac-
cording to technology with very high precision. Note
that, though there are effective pixels of 99.99% or
more, pixel missing or normally lit pixels account for
0.01%).
VRX835
43
12. ERROR DISPLAYS
If an error occurs, one of the following displays is displayed. Take the measures described to eliminate
the problem.
Error Display
ERROR 2
Cause
Measure
A CD is caught inside the CD deck and is This is a failure of CD deck’s mechanism
not ejected.
and consult your store of purchase.
ERROR 3
ERROR 6
ERROR 2
ERROR 3
ERROR 6
ERROR H
A CD cannot be played due to scratches,
etc.
Replace with a non-scratched,
non-warped-disc.
A CD is loaded upside-down inside the CD Eject the disc then reload it properly.
deck and does not play.
A CD inside the CD changer is not loaded. This is a failure of CD changer’s mecha-
nism and consult your store of purchase.
A CD inside the CD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-
warped-disc.
A CD inside the CD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
Displayed when the temperature in the MD Lower the surrounding temperature and
changer is too high and playback has
been stopped automatically.
wait for a while to cool off MD changer.
ERROR 2
ERROR 3
ERROR 6
An MD inside the MD changer is not
loaded.
This is a failure of MD changer’s mecha-
nism and consult your store of purchase.
An MD inside the MD changer cannot be
played due to scratches, etc.
Replace with a non-scratched, non-
warped-disc.
An MD inside the MD changer cannot be
played because it is loaded upside-down.
Eject the disc then reload it properly.
Displayed when a non-recorded MD is
loaded in the MD changer.
Load a pre-recorded MD in the MD
changer.
• If an error display other than the ones described above appears, press the RESET button. If the
problem persists, turn off the power and consult your store of purchase.
• For the DVD changer, refer to the Owner’s Manual provided with the DVD changer.
44
VRX835
13. SPECIFICATIONS
FM Tuner
Frequency Range: 87.50 MHz to 108.00 MHz
General
Power source voltage:
14.4 V DC (10.8 to 15.6 V allowable)
Usable Sensitivity: 11 dBf
Ground: Negative
50dB Quieting Sensitivity: 17 dBf
Alternate Channel Selectivity: 75 dB
Stereo Separation(1 kHz): 35 dB
Frequency Response( 3 dB): 30 Hz to 15 kHz
Current consumption: 4.0 A (1 W)
Auto Antenna Rated Current: 500 mA less
Dimensions of the Main Unit:
178 (Width) × 50 (Height) × 165 (Depth) mm
AM Tuner
Frequency Range: 531 kHz to 1629 kHz
Usable Sensitivity: 25 µV
Dimensions of the Tuner Amp Unit:
178 (Width) × 37.5 (Height) × 209.5 (Depth)
mm
Weight of the Main Unit: 2.0 kg
CD player
Weight of the Tuner Amp Unit: 1.1kg
System: Compact disc digital audio system
Frequency Response: 17 Hz to 20 kHz ( 1 dB)
Signal to Noise Ratio: 98 dB (1 kHz) IHF-A
Dynamic Range: 95 dB (1 kHz)
Distortion: 0.02%
Dimensions of the Remote Control Unit:
44 (Width) × 110 (Height) × 27 (Depth) mm
Weight of the Remote Control Unit:
30 g (including battery)
Audio Amplifier
Rated power output:
Main unit
17 W × 4 (20 Hz to 20 kHz, 1%, 4 Ω)
Maximum power output:
192 W (48 W × 4)
Speaker impedance: 4 Ω (4 to 8 Ω)
Input
Audio input:
130 60mVrms (input impedance 10kΩ or
greater)
172 mm
178 mm
(50 mm)
Video input:
Tuner amp unit
1.0 0.2 Vp-p (input impedance 75 Ω)
Video output
Video output:
1.0 0.2 Vp-p (output impedance 75 Ω)
LCD Monitor
Screen Size: 7-inch wide type
152 (Width) × 85 (Height) mm
Display method:
Transmission type TN liquid crystal display
178 mm
Drive method: TFT (thin-film transistor)
active matrix driving
(37.5 mm)
Notes:
Pixels: 336,960 (1440 × 234)
• Specifications comply with JEITA Standards.
• Specifications and design are subject to change
without notice for further immprovement.
VRX835
45
46
VRX835
VRX835
Installation and Wire connection manual
I Contents
1. BEFORE STARTING ............................................................... 47
2. PACKAGE CONTENTS ........................................................... 47
3. GENERAL CAUTIONS ............................................................ 48
4. CAUTIONS ON INSTALLATION .............................................. 48
5. INSTALLING THE MAIN UNIT ................................................. 49
6. REMOVING THE MAIN UNIT .................................................. 51
7. CAUTIONS ON WIRING.......................................................... 51
8. WIRE CONNECTION .............................................................. 52
9. SAMPLE SYSTEMS ................................................................ 55
1.
BEFORE STARTING
1. This set is exclusively for use in cars with a
negative ground 12 V power supply.
2. Read these instructions carefully.
3. Be sure to disconnect the battery “-” termi-
nal before starting. This is to prevent short
circuits during installation. (Figure 1)
Car battery
Figure 1
2.
PACKAGE CONTENTS
1 Main unit
8 Bag for accessories of the main unit (No. 2)
Hook plate ................................................... 2
Cord clamp
2 Tuner Amp unit
3 Manuals
Owner’s manual & Installation manual
Warranty card
Spacer
Special screw
4 Power supply lead (For the tuner amp unit)
9 Bag for accessories of tuner amp unit
Maunting bracket ........................................ 2
Canoe clip ................................................... 4
Machine screw (M4 × 8).............................. 4
0 Universal mounting bracket
! Remote control unit
5 Connection cord (Main unit ↔ Tuner amp
unit)
6 Antenna extension cord
7 Bag for accessories of the main unit (No. 1)
Flat head screw (M5 × 8) ............................ 4
Sems hexagonal bolt (M5× 8) ..................... 5
Electro tap
@ Battery
(for remote control unit)
Machine screw (M4× 3)............................... 4
# Outer Escutcheon
$ DCP Case
VRX835
47
3.
GENERAL CAUTIONS
1. Do not open the case. There are no user ser-
viceable parts inside. If you drop anything
into the unit during installation, consult your
dealer or an authorized CLARION service
centre.
2. Use a soft, dry cloth to clean the case. Never
use a rough cloth, thinner, benzine, or alco-
hol, etc. For tough dirt, apply a little cold or
warm water to a soft cloth and wipe off the
dirt gently.
4.
CAUTIONS ON INSTALLATION
1. Prepare all articles necessary for installing
the main unit before starting.
5. Use the enclosed screws for installation. Us-
ing other screws can cause damage. (Figure
4)
2. This model is used with the LCD panel slid
forwards (shell loading system). On some
types of cars, the LCD panel may touch the
dashboard or shift lever, in which case it can-
not be installed. Check that the set will not
hamper operation of the shift lever before
choosing the place of installation.(Figure 2)
Chassis
Chassis
Damage
Max. 8 mm
Dashboard
Figure 4
6. The source unit has mounting screw holes
for NISSAN (N marks) and TOYOTA (T
marks) vehicles.
T
N
T
Shift lever
Shift lever
(check that it does not
touch the LCD.)
Figure 2
3. Install the unit within 30° of the horizontal
N
T
N
plane. (Figure 3)
Figure 5
Max. 30˚
Figure 3
4. If you have to do any work on the car body,
such as drilling holes, consult your car dealer
beforehand.
48
VRX835
5.
INSTALLING THE MAIN UNIT
I Universal Mount
1. Place the universal mounting bracket into the
instrument panel, use a screwdriver to bend
each stopper of the universal mounting
bracket inward, then secure the stopper as
shown in Figure 6.
2. Wire as shown in Section 8.
Notes:
3. Insert the main unit into the universal mount-
ing bracket until it locks.
1) Some car models require special mounting kits
for proper installation. Consult your Clarion
dealer for details.
2) Fasten the front stopper securely to prevent
the main unit from coming loose.
4. Mount the outer escutcheon so that all the
hooks are locked.
• Console opening dimensions
Rear fastening hole (of vehicle)
Instrument panel
182 mm
Hole
Hole
Stoppers
Screwdriver
Rubber cap
Universal mounting bracket
Stoppers
Main unit
2-Spring
Outer escutcheon
Note:
Set the outer escutch-
eon so that its metallic
part on the back side
fits the upper edge of
the main unit.
Figure 6
VRX835
49
I Fixed Mount (TOYOTA, NISSAN and other ISO/DIN equipped vehicles)
This unit is designed for fixed installation in the
dashboard.
rection of arrow to remove it. Repeat the
same for the other side to remove the
springs from the both sides. (Figure 7)
If the vehicle is equipped with a factory-installed
radio, install the main unit with the parts and
screws marked (∗). (Figure 8)
If the vehicle is not equipped with a factory-in-
stalled radio, obtain an installation kit to install
the main unit in the following procedure.
2. Secure the mounting brackets to the chassis
as shown in Figure 8. Holes are pre-tapped for
TOYOTA and NISSAN vehicles; modification,
such as drilling new holes, of the mounting
brackets may be required for other models
.
3. Wire as shown in Section 8.
1. Remove the screws from both side of the
main unit. Then, at either side, lift the leaf
spring until the engaging claws are released
from the holes, and slide the spring to the di-
4. Secure the unit in the dashboard, and then
reassemble the dashboard and the centre
panel.
2-Screw
Engagin claw
Main Unit
2-Spring
Screwdriver
Figure 7
Mounting bracket #
(1 pair for the left and right sides)
4-Hexagonal screw ∗ (M5 × 8)
Main Unit
Pocket
Note 2
Centre Panel (Note 1)
∗: The screws with this mark
are enclosed in this set.
#:The parts and screws with this mark
are used to install radio or included in
the installation kit.
Figure 8
Note 1: In some cases, the centre panel may re-
quire some modification (trimming, filling,
etc.).
Note 2: If a hook on the installation bracket inter-
feres with the unit, bend and flatten it with
a nipper or a similar tool.
50
VRX835
6.
REMOVING THE MAIN UNIT
1. When the rear of the main unit has been se-
cured with the method shown in Figure 6 un-
fasten the special screw.
pull the main unit out by the hook plate. (In-
sert both the right and left edges of the hook
plate.) (Figure 9)
2. Remove the outer escutcheon.
Note: Keep the hook plate. You cannot remove the
3. Insert the hook plate between the spring and
the universal mounting bracket, fit tab B of
the spring into hole A of the hook plate, then
main unit without disengaging the hook plate.
Instrument panel
Universal mounting bracket
2-Hook plate
Main
Unit
Spring
Outer escutcheon
A
B
Figure 9
7.
CAUTIONS ON WIRING
1. Be sure to turn the power off before wiring.
Rear view of the tuner amp unit
2. Be particularly careful where you route the
wires.
Keep them well away from the engine, and ex-
haust pipe, etc. Heat may damage the wires.
3. If the fuse should blow, check to see if the
wiring is correct.
If it is, replace the fuse with a new one with
the same amperage rating as the original.
Fuse (15A)
Fuse
4. When any fuse is to be replaced, pull out the
fuse (15A) at the rear of the tuner amp unit
and put in a new one (Fig.10).
Figure 10
CAUTION
After the connection, fix the lead by a clamp or
insulation tape for protection.
5. To replace the fuse, release the catch on the
main unit side, remove the old fuse and in-
sert the new one. (Figure 11)
Fuse holder
Note: There are various types of fuse holder. Do not
let the battery side touch other metal parts.
Figure 11
VRX835
51
8.
WIRE CONNECTION
Securely connect to the
metal part of the car with a
screw, etc.
Black
Earth (ground) cord
Choke coil
Main power supply cord
Yellow
3A
Fuse
Connection cord (provided
with this unit)
CeNET cable (Sold separately)
Power supply lead
Subwoofer output terminal
L+R (RCA)
Front audio output (input)
terminal L+R (RCA) ∗4
&
Rear audio output (input)
terminal L+R (RCA) ∗4
Reset switch
DSP select switch (∗3)
Tuner amp unit
∗1 Top view of the
tuner amp unit
VISUAL 1 input (RCA)/TV TUNER input (RCA)
DVD input (RCA) (deck or changer) ∗8
¥
$
%
∗2 ∗7 ∗6
VISUAL 1 audio input terminal L+R (RCA)
VIDEO output (RCA) ∗5
52
VRX835
Purple/Black
Purple
2
1
8
Green/Black
Blue/White
Green
0
7
3
Brawn
(∗1
¡
Glay
Grass-green
No.
1
2
3
4
5
6
7
8
9
0
!
@
#
$
%
¥
&
*
(
)
¡
Description
Glay/Black
Orange/White
White/Black
Red
+
REAR RIGHT
REAR RIGHT
4
!
6
@
5
9
-
+
-
FRONT RIGHT
FRONT RIGHT
+
FRONT LEFT
FRONT LEFT
-
+
REAR LEFT
REAR LEFT
-
+12 V MAIN POWER
AUTO ANTENNA
ILLUMINATION
+12 V ACCESSORY
GROUND
CCD/M.LOCK terminal
VISUAL 2 terminal
Radio antenna jack (∗2)
CeNET terminal
Spare terminal (Black)
Phone mute (Brown) (∗1)
Spare terminal (Yellow)
Parking brake (Grass-Green)
White
Yellow
)
Black
#
*
∗1: Connecting the PHONE MUTE Terminal
The lead included with the unit must be connected to the specified position of the vehicle’s con-
nector in order to use the “triggered audio mute for cellular telephones” function.
∗2: Use the attached extension lead when necessary. (Provided with this unit)
Note : Before making any installation, disconnect the car battery - (negative) cable.
∗3: When a DSP (sold separately) is connected and the internal amp of the Tuner Amp Unit is used,
set the DSP select switch to “D”. Then, the AUDIO OUT (IN) terminal of the Tuner Amp Unit is
N
D
only available for audio input, not outputting the audio.
∗4: Connect to a separately sold external anplifier, DSP, etc. with a separately sold RCA cord (L,R).
∗5: Connect to a separately sold Rear view monitor for the rear seat.
∗6: Connect to separately sold VTR equipment.
∗7: M. LOCK function is available only on this connection terminal.
∗8: DVD deck and DVD changer can not be connected at the same time.
VRX835
53
I Connecting the Accessories
• Connection to the external amplifier
The external amplifier cannot be connected unless the DSP is connected. For detailed information,
refer to the instruction manual of the DSP.
• Connection to the CCD camera for vehicle
The CCD camera for vehicle can be connected to the CCD terminal on the tuner amp unit. For
detailed information, refer to the instruction sheet or manual for the CCD camera.
Notes:
• A power supply box (sold separately) is required for connection of the tuner amp unit and the CCD camera.
• While the CCD camera is used, the navigation cannot be turned on.
• The power supply box for camera CAA147 cannot be used. Please use the CAA188 instead.
• If the specified lead of the cellular phone is connected to the phone mute
lead of the source unit, the audio mute is available when the cellular tele-
phone is used.
• TV Tunner
When the TV TUNER is to be connected, connect the CeNET connector and RCA PIN (yellow). For
detailed information, refer to the instruction manual of the TV TUNER.
Parking brake lamp
I Connecting the parking brake lead
Connect the lead to parking brake lamp earth
+ lead to battery
in the meter panel.
Connect these three leads.
Notes:
- cord
• Connecting the parking brake lead to lamp earth
allows you to watch TV/VTR/DVD video/DVD
changer when the parking brake is engaged.
• When the parking brake lead is not connected,
the monitor will stay off.
parking
brake signal
lead
Parking brake lead
(bright green)
Parking brake
54
VRX835
9.
SAMPLE SYSTEMS
I Sample System 1
VRX835
Front
Speakers
Rear
Speakers
RCA video cable (sold separately)
Tuner Amp Unit
Rear View
Monitor
DVD input
VISUAL 1 (TV TUNER)
input
RCA video cable
(included the TV tuner)
CeNET cable
(included the
TV tuner)
TV tuner
(TTX7504z,
TTX7501z,
TTX7503z)
CeNET Cable
(included the Changer)
Ferrite clamp
(Included the DVD changer)
CeNET Y-adapter
(CCA-519, sold
separately)
CeNET DVD Changer
CeNET CD Changer
(VCZ625)
(DCZ625)
Set the [CeNET/STAND ALONE]
switch to the [CeNET] position.
STAND
ALONE
CeNET
VRX835
55
I Sample System 2
VRX835
RCA video cable
(sold separately)
Rear View
Monitor
AV Adapter cable
(CCA-389,
sold separately)
VTR
VISUAL 2 input
DVD input
Tuner Amp Unit
Front
Speakers
TV Tuner input
CeNET
cable
(included
the TV
tuner)
RCA video cable
(included the TV tuner)
RCA cable
(sold separately)
CeNET TV Tuner
Rear
Speakers
(TTX7504z,
TTX7501z,
TTX7503z)
4-Channel
Amplifier
CeNET cable
(included the
DPH910)
Sub-woofer
2-Channel
Amplifier
Digital Sound
Processor
RCA cable
(sold separately)
(DPH910)
Ferrite clamp
(Included the DVD changer)
CeNET cable
(included the VCZ625)
CeNET DVD Changer
(VCZ625)
Set the [CeNET/STAND ALONE]
switch to the [CeNET] position.
STAND
ALONE
CeNET
56
VRX835
|