™
communication in motion™
Q2™ MultiSet
Gebrauchsanleitung
Guide d’Utilisation
Guida di Avvio
Guia de Usario
User Guide
INTRODUCTION
Congratulations and thank you for choosing the scala rider Q2
CONTENTS OF RETAIL BOX
MultiSet Bluetooth® Headset package for bikers.
Volume
Two Headsets
This User Guide will help you operate the headset, but you should
first familiarize yourself with the Bluetooth functionality of your cel-
lular phone and/or GPS device before using the scala rider Q2.
Up
Charging
Jack
This retail box contains two scala rider Q2 headsets that already factory
paired (see details below). In wide open terrain two bikers can commu-
nicate via intercom (in full duplex*) at a range of up to 500 m / 1,640 ft.,
subject to terrain and external conditions.
Volume
Down
CTRL – Control Button
• Power On, Power Off
• Answer/End Call
MC – Multi-Connection
• Radio On/Off/change stations
• Initiate/Terminate Buddy
Intercom call with Primary or
Secondary Buddy
The scala rider Q2 is multi-talented and (in addition to its connec-
tion to the second Q2 unit) it can also serve as a stand-alone unit for
the following connectivity modes:
• As a Bluetooth headset for mobile phone communication**
• As a Biker-to-Passenger Intercom device that connects with any
scala rider headset worn by the passenger
Left Speaker
(short cord)
Two Helmet Clamps
• As a speaker that transmits GPS Navigation instructions from a
compatible GPS device***
Right Speaker
(long cord)
• As a speaker that transmits audio from the embedded FM Radio
• As a speaker that transmits music from your MP3 player
Microphone
NOTE: Each Q2 headset can establish an audio connection with one
Bluetooth device at a time. Read the section “Using the Headset” on
how to switch the audio connection between the paired devices.
Back
Plate
Tab
Sliding Plate
____________________
* Full duplex calls allow you to speak and hear the other party speak simultaneously
MP3 Jack
NOTE: Th
** Mobile phones that do not support the Bluetooth Handsfree profile may prevent you
from using the Redial and Call Reject features. The Q2 supports headset and handsfree
profiles at up to 10 m / 30 ft. distance from the mobile phone
rider Q2 i
able in a c
version to better fit certain full-faced
helmets with tight chin sections.
*** Requires Bluetooth compatibility on the part of the GPS device
scala rider® Q2™ MultiSet
3
2 Wall Chargers
SET UP AND CONFIGURATION
2 Allen Wrenches
2 sets of Velcro Pads
2 MP3 Cables
GPS
Built-in
FM radio
Mobile
phone
MP3
player
2 MP3 Cable Holders
2 Glue Plates
Driver-to-
Passenger
Full-duplex
Intercom
2 Pre-moistened Towelettes
2 Carry-Pouches
Connection
Bike-to-Bike Intercom
up to 500 m / 540 yd
)in open terrain(
4 Microphone Sponges
Flat sponge for full-face helmets and round sponge for other helmet types
scala rider Q2 or
other scala rider
User Guide, including Warranty and Registration form
headset
IMPORTANT:
Your headsets are water-resistant, designed for use under moderate
rain or snow conditions. However, the headsets are not waterproof
and should not be used under severe weather conditions.
The cover tongue protecting the Charging Jack should be kept tightly
closed at all times to prevent moisture from entering the device.
STEP 1
SET UP FOR BIKE-TO-BIKE INTERCOM: PAIRING
NOTE: WHILE MOST INSTRUCTIONS IN THIS MANUAL REFER TO THE HEADSET IN THE
Pairing is a one time process that is required for mutual recognition be-
tween a headset and other Bluetooth devices. Once the two headsets
are paired, they will remain paired and automatically recognize each
other whenever they are within range. The two headsets in your retail
box are already factory paired and relate to each other as the Primary
Buddy connection. In addition, each unit can be paired with an addi-
tional scala rider headset for Intercom communication. Please note that
you can speak via Intercom to one Buddy headset at a time.
SINGULAR, THEY APPLY TO BOTH UNITS UNLESS INDICATED OTHERWISE.
BEFORE USING (CHARGING THE
HEADSET)
Make sure that the headset is fully charged for at least five hours
before initial use.
1. Connect the wall charger to the headset’s Charging Jack (located
between the two Volume Buttons).
2. While charging, the Red Light turns on (it may take up to 15
seconds until the Red Light turns on). When charging is complete,
the Red Light will turn off.
NOTE: This Manual refers to the Intercom users and other parties as:
Primary Buddy and Secondary Buddy.
scala rider® Q2™ MultiSet
4
PRIMARY BUDDY PAIRING (two scala rider Q2
STEP 2 (Optional)
headsets)
SET UP FOR RIDER-TO-PASSENGER INTERCOM: PAIRING
There are two ways that the scala rider Q2 can be used for Driver-to-
Passenger communication.
A. Both Rider and Passenger are using scala rider Q2 headsets (like
Your two MultiSet units are already factory paired and ready for use. If
for any reason, you have to pair them again, proceed as follows:
1. If either headset is turned OFF, turn it ON by pressing and holding
the CTRL Button until the Blue Light flashes three times.
the two units in your retail package).
To Pair the two headsets, follow the Steps listed in the section
2. Make sure that both headsets are now flashing slowly in Blue.
above titled PRIMARY BUDDY PAIRING (2 bikers)
3. Pick up one headset and simultaneously press and hold the CTRL
Button and MC Button for at least six seconds until the Red Light
begins flashing rapidly, indicating it is in Intercom Pairing mode.
B. The Rider is using a scala rider Q2 and the Passenger is using an
earlier scala rider headset (i.e. a scala rider Solo, a scala rider
FM or a scala rider TeamSet Driver unit headset).
4. Repeat Step 3 again for the second scala rider Q2 headset. Both
headsets should now be flashing rapidly in Red.
To Pair the two headsets:
1. Starting with the earlier scala rider headset turned OFF, press
and hold the CTRL button until the Red/Blue lights begin
rapidly alternating.
5. Within a few seconds, both headsets will show a solid Red
light for two seconds, and then begin flashing slowly in Blue.
NOTE: If the Pairing process is not completed within one
minute the headset will return to Standby mode.
2. Starting with the scala rider Q2 turned ON, simultaneously
press and hold the CTRL Button and MC Button for six
seconds until the Red light begins flashing rapidly, indicating it
is in Intercom Pairing mode.
3. Within a few seconds, the scala rider Q2 will show a solid Red
light for two seconds, and then begin flashing slowly in Blue.
SECONDARY BUDDY PAIRING (requires three
scala rider Q2 headsets)
In addition to the Primary Buddy pairing between the two units
in your retail box you can pair your headset with the Secondary
Buddy headset by repeating the above pairing procedure.
NOTE: If the Pairing process is not completed within one minute the
headset will return to Standby mode.
NOTE: When using an earlier scala rider headset as a Passenger head-
set, Voice Connect Intercom can be initiated only by the scala
rider Q2 headset. Manual Connect Intercom can be initiated
from either headset by pressing the MC button for scala rider
Q2 and CTRL button for any earlier scala rider headset.
NOTE: Your headset can communicate with either the Primary
Buddy or the Secondary Buddy. However, neither
the Primary Buddy nor the Secondary Buddy can
communicate among each other directly via Intercom.
RESET INTERCOM PAIRING
You can delete all of the headset’s Intercom pairings at any time.
NOTE: If the Pairing process is not completed within one
minute the headset will return to Standby mode.
scala rider® Q2™ MultiSet
5
1. Place the scala rider Q2 into Intercom Pairing mode following the
instructions in the PRIMARY BUDDY PAIRING section above.
phone’s instructions. Please consult your phone’s User Manual
for more information.
4. After a few seconds the phone will list the scala-rider Q2
as a discovered device. Select it and follow your phone’s
instructions to accept the pairing.
2. Once the Red Light begins flashing rapidly, press and hold Volume
up for three seconds.
3. The Red and Blue Lights will flash five times, confirming that the
Reset Pairing was successful.
5. When prompted enter 0000 (four zeros) as your PIN or passkey.
6. Your phone will confirm that pairing has succeeded and the
headset will begin flashing slowly in Blue.
STEP 3
NOTE: If the Pairing process is not completed within two minutes the
headset will return to Standby mode.
SET UP FOR MOBILE PHONE CALLS: PAIRING
If you have a Bluetooth enabled mobile phone and would like to
make and receive phone calls using the scala rider Q2, you must first
pair your headset to the mobile phone.
With some mobile phones, you may need to tap the CTRL button
to connect the headset to the phone after pairing is complete. The
scala rider Q2 headset will automatically connect to the last phone
connected to the headset.
NOTE: If you have a compatible Bluetooth GPS device you wish to
use with the scala rider Q2, please skip this step, and continue
ahead to STEP 4: SET UP FOR BLUETOOTH GPS DEVICE.
STEP 4
SET UP FOR BLUETOOTH GPS DEVICE: PAIRING
Pairing is a one time process. Once the headset is paired to a
specific mobile phone during this Setup Procedure, they will
remain paired and automatically recognize each other whenever
they are within range. If the connection between the phone and
headset is lost, tap the CTRL button to reconnect the devices.
If you have a Bluetooth enabled GPS device and would like to transmit
navigation instructions and sounds from the GPS device through the
headset’s speakers, you must first pair your headset to the GPS device.
NOTE: Not all Bluetooth enabled GPS devices allow connections to
Bluetooth headsets like the scala rider Q2. Please consult your GPS
device’s User Manual for more information.
TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH
MOBILE PHONE
TO PAIR THE SCALA RIDER Q2 TO A BLUETOOTH GPS
DEVICE:
1. Turn on your phone and make sure its Bluetooth function is
activated.
2. With the scala rider Q2 headset turned ON, press and hold
the CTRL Button for at least six seconds until the Red and Blue
Lights begin rapidly alternating.
1. Turn on your GPS device.
2. With the scala rider Q2 headset turned ON, press and hold
the CTRL Button for at least six seconds until the Red and Blue
Lights begin rapidly alternating.
3. Search for Bluetooth devices on your phone by following the
scala rider® Q2™ MultiSet
6
3. Search for Bluetooth headsets on your GPS device by following
the device’s instructions. Please consult your GPS device’s User
Manual for more information.
2. Slide the Back Plate between the internal
padding and the external shell of the helmet.
3. Adjust the clamp’s location so that the
microphone is located opposite your mouth
and then tighten the screws. You may need
to reposition the Clamp repeatedly until you
identify the best spot. The microphone must
be positioned vertically and not horizontally.
If you have purchased a helmet clamp version with the corded micro-
phone, please refer to section ATTACHING THE CORDED MICROPHONE
CLAMP ON A FULL-FACED HELMET
4. If your GPS device prompts for a PIN or Passkey enter 0000 (four zeros).
5. Your GPS device will confirm that pairing has succeeded. The
headset will begin flashing slowly in Blue.
6. If you wish to use a Bluetooth mobile phone to make and
receive calls through the headset, you must now pair your
mobile phone to your GPS device by following your GPS
and/or mobile phone’s instructions.
NOTE: If the Pairing process is not completed within two
minutes the headset will return to Standby mode.
Glue Plate Method
You have the option to glue the Helmet Clamp onto your helmet,
when the above standard method cannot be used, or in case you
prefer to secure the Helmet Clamp with adhesive glue. This option
has been successfully used for a range of high end helmets.
GETTING STARTED
ATTACHING THE CLAMP ON THE HELMET
The Helmet Clamp must be attached to the left side of the helmet.
Once attached, the headset unit can be mounted or released from
the Helmet Clamp at any time. If you wish to connect your MP3 player
to your headset, please refer first to the assembly instructions listed in
section: USING THE MP3 PLAYER WITH YOUR HEADSET.
NOTE: While we have no reason to believe that the gluing option might
negatively affect any helmet, Cardo does not assume any responsibility to
that affect, irrespective of its nature and circumstances. The Glue Plate is
offered as a free option that you may choose to use at your own risk and
subject to renouncement of any future claims.
There are two methods that can be used in order to attach the Clamp
onto the helmet:
Caution: This process can be done only once!
1. Use the enclosed Allen Wrench to remove both Allen
screws and release the Helmet Clamp’s back plate.
Standard Method: Recommended for most helmet types.
2. Determine the location on the helmet where the Hel-
met Clamp must be attached.
3. Adjust the Helmet Clamp’s location on the Helmet so that the
microphone is located opposite your mouth. You
may need to reposition the Clamp repeatedly until
you identify the best spot. The microphone must
be positioned vertically and not horizontally (Be
Glue Plate Method: Recommended for helmets to
which the standard method cannot be applied,
using the Glue Plate included in the box.
Standard Method
1. Use the enclosed Allen Wrench to loosen the
two screws on the Back Plate.
scala rider® Q2™ MultiSet
7
sure to clean the selected area prior to the gluing process).
POSITIONING THE SPEAKERS
4. Use the pre-moistened Towelette to clean the helmet area where
you want to install the Glue Plate. Allow to dry thoroughly.
5. Peel the foil cover from the Glue Plates’ adhesive pad.
6. Place the Glue Plate into position according to #3. Press firmly 15
seconds on all 3 parts of the Glue Plate.
7. The adhesive pad bonds to full strength over the next 24 hours.
Therefore it is recommended to not use the headset during this 24
hour period.
8. Fasten the Clamp to the Glue Plate using the Allen screws that were
previously removed.
Attach the speakers to the Velcro inside
your helmet opposite your ears (short
speaker cord for the left ear [A] and the
long speaker cord [B] for the right ear). You
may want to use the supplied Velcro pad.
Speaker A
Speaker B
Using two speakers inside the helmet
may be prohibited in certain
jurisdictions. If this is the case,
you should tuck away the long
corded speaker underneath the
helmet padding as follows:
Cable
Speaker B
If you have purchased a helmet clamp version with the corded
microphone, please proceed as follows:
Lead the speaker cord [B] along-
side the rim of the padding to
the right side and then back
to the left side, near speaker
[A]. Then place the speaker [B]
underneath the padding.
ATTACHING THE CORDED MICROPHONE CLAMP ON A
FULL-FACED HELMET
Speaker B
If you are using the corded microphone version, you must first make
sure your helmet clamp is attached to your
helmet as described in previous section
(ATTACHING THE CLAMP ON THE HELMET).
Clean the exact spot on the internal padding of
the helmet, opposite your mouth, where the
microphone will be placed and proceed as
follows.
Speaker A
ATTACHING AND REMOVING THE
a. Peel the foil cover from the adhesive Velcro
pad and place the Velcro pad on the chosen
location opposite your mouth.
HEADSET FROM THE HELMET CLAMP
ATTACHING:
b. Attach the microphone to the Velcro, as shown
in photo.
Slide the headset downwards along the
sliding panel until a clicking sound indi-
cates that the headset is locked in place.
c. When done, tighten the screws of the clamp
scala rider® Q2™ MultiSet
8
A high priority Audio Source will always interrupt any lower priority
Audio Source.
Press here
to remove
REMOVING:
Your headset can be removed for charg-
ing and storage by pressing your finger
gently against the tab and sliding the
headset up with the other hand.
i.e.
Mobile phone call interrupts Intercom call
Intercom call interrupts FM Radio
USING THE INTERCOM
Making Intercom calls
We recommend that you remove the
headset from the helmet when not in use.
USING THE HEADSET
GENERAL USAGE
To start a Buddy Intercom call with the Primary Buddy while
the headset is on Standby you can either:
GENERAL FUNCTIONS
REQUIRED ACTION:
Press the CTRL Button steadily for at least three
seconds
VOICE CONNECT:
Start talking
or MC BUTTON CONNECT:
DESIRED RESULT:
Turn on the
headset
Turn off the
headset
Single tap the MC Button
A Buddy Intercom call will be
established and stay on until
both sides are quiet for 30
seconds.
A Buddy Intercom call will
be established. To end the
Buddy Intercom call, single
tap the MC Button again.
Press the CTRL Button steadily for at least three
seconds
Increase the
volume
Decrease the
volume
Short press the Volume Up Button
To start a Buddy Intercom call with the Secondary Buddy
while the headset is on Standby:
Short press the Volume Down Button
MC Button
MC BUTTON CONNECT:
AGC (Automatic Gain Control): In addition to manual Volume Control,
the scala rider Q2 will automatically increase and reduce its volume
according to ambient noise and driving speed.
Double tap the MC Button
A Buddy Intercom call will be established. To end the
Buddy Intercom call, double tap the MC Button again.
AUDIO SOURCES AND PRIORITIES
NOTE: When using a scala rider Headset (not a Q2
Passenger headset, Voice Connect Intercom can be initiated only
by the scala rider Q2 headset. Manual Connect Intercom can be
initiated from either headset.
The different Audio Sources that are connected to the scala rider Q2
are prioritized as follows:
Highest 1. Mobile phone Audio / GPS device (Incoming/outgoing calls ,
GPS audio and navigation instructions)
2. Primary Buddy Audio and Secondary Buddy Audio
3. FM Radio
Failed Connection: On the scala rider Q2, if you attempt to start
a Buddy Intercom call with a Buddy that is already on a Phone/GPS/
Intercom call, you will hear a double beep indicating the Buddy is busy.
Lowest 4. MP3 Connectivity
scala rider® Q2™ MultiSet
9
Reconnecting the Intercom: If the scala rider Q2 and its Intercom
Buddy headset go out of range and disconnect from each other, the
scala rider Q2 will automatically try to reconnect to its Intercom
Buddy for five minutes.
Press and hold the Volume Up Button for three seconds and
you will hear a beep:
• One beep – Voice Connect set to Primary Buddy
• Two beeps – Voice Connect set to Secondary Buddy
You can manually reconnect at any time by pressing the MC Button
(single tap for Primary Buddy and double tap for Secondary Buddy).
Enable/Disable Voice Connect feature
Press and hold the Volume Up and Down Buttons simultaneously
until you hear a beep. The default status is Voice Connect enabled.
Receiving Intercom calls
If you are not speaking with any one, once the other party tries to
initiate a Buddy Intercom call, the call will begin immediately.
NOTE: The Enable/Disable Voice Connect feature affects the
Intercom functionality only.
MAKING AND RECEIVING MOBILE
PHONE CALLS
TROUBLESHOOTING THE INTERCOM:
First, make sure your microphone is located properly in front of
the center of your mouth.
PHONE FUNCTIONS
The scala rider Q2 is designed for use in loud environments.
Please make sure to test the Intercom functionality in a LOUD
environment, such as next to an idling motorcycle.
Short press the CTRL Button or speak loudly any
word of your choice during an incoming call.
Answer a call
Reject a call
Short press the MC Button or remain silent for
15 seconds during an incoming call.
Please also verify that the headsets were paired together properly
by following the instructions in the relevant Setup sections.
Short press the CTRL Button to end a call.
Terminate a call
Voice Dial
During Standby, short press the CTRL Button
and state the name of the person you wish to
call. This feature is supported only by mobile
phones that support the Voice Dial feature.
Setting Voice Connect Intercom preference (Primary vs.
Secondary Buddy)
The headset’s Voice Connect feature allows you to start a Buddy
Intercom call by simply speaking into the microphone. You can
define which of the two Buddy headsets you wish to connect to
when using Voice Connect Intercom.
Press and hold the Volume Down Button for
three seconds during Standby.
Redial
NOTE: The Primary Buddy has priority by default.
NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS
device, not directly to the scala rider Q2, some of the above Phone
functions may not be compatible.
To toggle the Voice Connect Intercom between Primary and
Secondary Buddy:
scala rider® Q2™ MultiSet
10
When the headset is on an active phone call, any Buddy Intercom call
request will be rejected automatically.
received, or when you decide to initiate a call. When the conversation
is over, the headset automatically tunes back in to the FM Radio.
Once the phone call audio link drops, you can initiate and accept
Buddy Intercom calls.
Turning the FM Radio On
While no call is on the headset (either mobile phone call or Intercom
call), press and hold the MC Button on your headset for three seconds
to turn on the radio. The radio tunes in to the last radio station you
were listening to. With some phones you should wait a few seconds
after ending a call before turning on the Radio.
STATUS LIGHT STATES
None
Headset is off
Alternating Red/blue flashes
Mobile phone/GPS Pairing
mode
Turning the FM Radio Off
While the radio is turned on, press and hold the MC button for three
seconds to turn the Radio off.
Rapid Red flashes
Intercom Pairing mode
1 blue flash every 3 seconds
Standby – No call is in progress
Switching Preset FM Radio Station
2 blue flashes every 3 seconds Call being initiated or in
progress / FM Radio ON
There are six pre-set Radio stations available on your scala rider Q2.
While the Radio is on, tap the MC Button to cycle between saved
stations.
1 red flash every 3 seconds
Battery is low
2 red flashes every 3 seconds Call being initiated or in
progress / FM Radio ON and
Searching for a New FM Radio Station
battery is low
While the Radio is on, press and hold the Volume Up or Volume
Down Button for three seconds or until you hear the next station on
your headset.
Solid red
Headset is being charged
Pressing Volume Up will search upwards (higher frequency). Pressing
Volume Down will search downwards (lower frequency). Once a
station is found, searching stops and you can hear the station.
WORKING WITH THE FM RADIO
Your headset is equipped with a high-quality FM Radio receiver. This
section explains how to enjoy the functions of the FM Radio.
To save this station, refer to the following section.
The scala rider Q2 enables you to listen to FM Radio while you are
not receiving audio from another audio source.
To continue searching, press the Volume Up or Volume Down Button
again for three seconds.
While listening to the radio, you do not have to worry about missing
any calls, as the headset automatically mutes the FM Radio and
switches to Bluetooth headset operation when an incoming call is
You may still continue to listen to the current unsaved station.
Pressing the MC Button in this case will switch to the next saved
station.
scala rider® Q2™ MultiSet
11
Saving an FM Radio Station
4. Attach the clamp and headset onto your helmet as described
previously in section “ATTACHING THE CLAMP ON THE HELMET”.
5. Attach the speakers to your helmet as described in section
”POSITIONING THE SPEAKERS”.
The FM Radio is equipped with a memory capacity of six stations.
• Select the station you wish to replace by tapping the MC button
until you find the station you want to replace.
6. Connect the MP3 cable to your MP3
player device’s jack and the other
side to the helmet Clamp’s jack,
inserting the cable through the MP3
cable holder.
Make sure that the cable plug clicks
into place.
7. Tuck the MP3 cable into the hook of the MP3 cable holder.
8. In order to use your MP3 player, power on the headset to have it
on Standby mode, flashing slowly in Blue.
• Search for a new station as described above.
• Tap the MC Button within 20 seconds of finding the station to
save the current station.
Insert cable in hook
If you don't save the station, the Radio will exit search mode without
saving the current station. You can still continue to listen to the
current unsaved station. Tapping the MC Button in this case will
move to the next saved station.
USING THE MP3 PLAYER WITH YOUR
HEADSET
NOTE: Operate the MP3 Player device by using its buttons (FF/REW/
PLAY/PAUSE).
Your scala rider Q2 headset can be connected to an MP3
player device by plugging it to the Helmet Clamp’s jack with
the MP3 cable.
Volume can only be adjusted through the MP3 Player.
Any other audio connection will automatically mute the MP3
Player. The audio signal will return only when headset is once
again in Standby mode.
At your option, you may further secure the MP3 cable by using the
MP3 cable holder. For this purpose please proceed as follows:
1. Use the enclosed Allen Wrench to
remove both Allen screws from
Helmet clamp and release the
clamp’s back plate.
SUPPORT
For additional information please visit our website at
2. Place the MP3 cable holder on the
helmet clamp. Both pins on the MP3
cable holder should be fixed into
corresponding indentations on clamp.
3. Place the Back Plate on top of the MP3 cable holder and secure
all parts together using the Allen screws that were previously
removed, as shown in photo.
MP3 cable holder hook
or contact us at:
Phone: USA and Canada – + 1-800-488-0363
International – +4989 450 36819
scala rider® Q2™ MultiSet
12
15.105(b)
NOTICES
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the IC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Federal Communications Commission (FCC) Statement
15.21
You are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.
15.105(b)
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause
undesired operation of the device.
IC RF Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying RF
exposure compliance. This transmitter must not be co-located or operating in conjunc-
tion with any other antenna or transmitter.
• Consult the dealer or an experienced radio/TV technician for help.
Operation is subject to the following two conditions:
1) this device may not cause interference and
2) this device must accept any interference, including interference that may cause
undesired operation of the device.
European CE Notice
The scala rider Q2™ headset (the “Product”) is in conformity with the following essential
requirements of Council Directive 1999/5/EC (referred to as R&TTE Directive): Articles
3.1a, 3.1.b and 3.2. The Product is manufactured in accordance with Annex II of the
above directive.
FCC RF Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. End users must follow the specific operating instructions for satisfying
RF exposure compliance. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Declaration of Conformity (DOC)
The scala rider Q2™ headset is compliant with and adopts the Bluetooth® Specifica-
tion 2.0 and has successfully passed all interoperability tests that are specified in the
Bluetooth® specification. However, interoperability between the device and other
Bluetooth®-enabled products is not guaranteed.
Industry Canada (IC) Statement
15.21
WAIVER AND GENERAL RELEASE
You are cautioned that changes or modifications not expressly approved by the part
responsible for compliance could void the user’s authority to operate the equipment.
By using the scala rider Q2 headset(s) – hereafter referred to in the singular – you
will waive substantial legal rights including the right to sue. Please read the
scala rider® Q2™ MultiSet
13
following carefully before using the device. If you do not accept all terms of this
agreement, you should immediately return the product for a full refund. By using
the headset you agree to be bound to this agreement and forfeit the right to sue.
confirm that you will not consume any alcohol that may affect your alertness or any
mind-altering substance, and will not carry, use or consume these substances before
or during the use of the Device.
Using a communication device while riding a motorcycle, scooter, moped, ATV, quad-
bike or any other vehicle or equipment, whether on land, water or air (jointly referred
to as “Vehicle”) requires your complete and undivided attention. Cardo Systems, Inc.,
including its Officers, Directors, Affiliates, Parent Company, Representatives, Agents,
Contractors, Sponsors, Employees, Suppliers and Resellers (jointly referred to as the
“Company” or “Cardo”) strongly advises you to take all necessary precautions and remain
alert to the traffic, weather and road conditions if you choose to use the scala rider Q2
headset, including all derivative models irrespective of its commercial name or branding
(the “Device”), and stop your Vehicle on the roadside prior to initiating or receiving calls.
Any publications, advertisements, announcements or similar notes that refer to using the
Device while riding a Vehicle are solely intended to address its technical capabilities and
should not be misconstrued as if encouraging users to operate the Device while actively
involved in traffic.
4. You fully acknowledge our warnings and understand that: (a) risks and dangers exist
in using the Device while in traffic, including but not limited to injury or illness, strains,
fractures, partial and/or total paralysis, death or other ailments that could cause serious
disability; (b) these risks and dangers may be caused by the negligence of the manu-
facturers or its agents or any third party involved in designing or manufacturing the
Device; (c) these risks and dangers may arise from foreseeable or unforeseeable causes.
You hereby assume all risks and dangers and all responsibility for any losses and/or
damages, whether caused in whole or in part by the negligence or other conduct of
others, including the Company.
5. You confirm that you have read this release of liability and fully understand its terms
and that you have given up substantial rights by not returning the Device for a full
refund (see refund option below).
By way of purchasing this Device and not returning it for a full refund (see below), you
are irrevocably releasing, indemnifying from any liability, loss, claim and expense
(including attorneys fees) and holding Cardo harmless for any bodily injuries, harm or
death as well as losses or damages in goods, to any Vehicles including your own, or to
any property or asset that belong to you or to third parties, any of which may result from
using the Device under any circumstances or conditions and irrespective of jurisdiction.
Cardo will not be responsible for any physical damages, irrespective of reasons, condi-
tions or circumstances, including malfunctioning of the Device, and all risks associated
with operating it rest solely and entirely with the user of this Device, irrespective of
whether the Device is used by the original purchaser or any third party.
Disclaimer of Warranty
CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE
ENCLOSED DEVICE, INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF
MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NON-INFRINGEMENT.
THE DEVICE AND ITS ACCESSORIES ARE PROVIDED “AS IS” AND “AS AVAILABLE” WITHOUT
WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL.
Limitation of Liability
IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL, INDIRECT, PUNITIVE,
INCIDENTAL, EXEMPLARY OR CONSEQUENTIAL DAMAGES, OR ANY DAMAGES
WHATSOEVER RESULTING FROM THE USE OF THE DEVICE, WHETHER BASED ON BREACH
OF CONTRACT, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. YOU ACKNOWLEDGE AND
AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF
THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH
LIMITATIONS. SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY.
Cardo hereby notifies you that using this Device may also be in contravention to local,
federal, state or national laws or regulations, and that any use of the Device is entirely at
your sole risk and responsibility.
1. You, your heirs, legal representatives, successors or assigns, hereby voluntarily and for-
ever release, discharge, indemnify and hold harmless Cardo from any and all litigation,
claims, debts, demands, actions and liability which may arise, directly or indirectly,
from using the Device for any distress, pain, suffering, discomfort, loss, injury, death,
damages to or in respect to any person or property however caused, WHETHER ARIS-
ING FROM THE NEGLIGENCE OR OTHERWISE, and which may hereafter accrue to you
on some future date as a result of said use, to the fullest extent permitted by law.
RETURN FOR FULL REFUND
IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDITIONS, YOU
MAY RETURN THIS DEVICE TO THE STORE FOR A FULL REFUND, PROVIDED THAT
YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOLLOWING THE PURCHASE OF THE
DEVICE (proof of purchase required) AND SUBJECT TO THE RETAIL BOX AND ALL AC-
CESSORIESBEINGCOMPLETEANDINTACT. WHENDOINGSO, PLEASEREFERTOTHIS
SECTION. BY NOT RETURNING THE DEVICE FOR REFUND WITHIN THE PERIOD PRO-
VIDED, YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE, AND RENOUNCE ALL
RIGHTS TO FUTURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED ABOVE.
2. You fully understand and assume the risks in using the Device, including risk of negli-
gent acts or omissions by others.
3. You confirm that you are physically capable to use the Device and that you have no
medical conditions or needs that may infringe upon your abilities to do so in a safe
manner. You confirm that you are at least eighteen (18) years of age and that you
have been advised of the risks associated with the use of the Device. You further
scala rider® Q2™ MultiSet
14
|