BLUETREK X2 user guide
Thank you for choosing the BLUETREK® X2, we hope you will enjoy the convenience
we are bringing to you. The BLUETREK® X2 offers many functions, please read this
manual before getting started.
EC-Declaration of Conformity
We, Innovi Technologies Ltd of
31/F China Online Centre,
333 Lockhart Road,
Wan Chai, Hong Kong
declare under our sole responsibility that our product
BLUETREK X2-2
to which this declaration refers is in conformity with the appropriate standards
EN300 328-02
EN301 489-17
EN301 489-01
EN50371
EN60950
Following the provisions of Radio and Telecommunications Terminal Equipment
directive 1999/5/EC.
November 2005
Guillaume Ponticelli, Director of Development
PAGE 1 / 6
BEFORE USING YOUR HEADSET FOR THE FIRST TIME
-
You must charge it continuously for about 8 hours, until the red indicator light
turns off. Please refer to the “Charging the BLUETREK® X2” section of this
manual.
-
Pair the headset with a mobile phone. Please refer to the “Pairing the
BLUETREK® X2” section of this manual.
Introduction
The BLUETREK® X2 headset is a wireless headset based on the Bluetooth®
technology. It complies with Bluetooth® 1.2 protocol, supporting Headset and Hands-
free profile.
The BLUETREK® X2 headset has 3 buttons:
• “TALK “button (main button),
•
1 “VOL+ “button,
• 1 “VOL- “button.
Charging the BLUETREK® X2
Please connect the charger to the headset and to the mains. During the charge, the
indicator light is red. The indicator light will turn off when the charge is complete. During
subsequent charges, the charging should take approximately 2 hour 40 minutes.
When you hear a light beep in your headset at regular intervals, and the indicator light
flashes in red, your headset needs to be recharged.
Important:
• To maximize battery lifetime, it is recommended to recharge your headset to full
capacity only when the battery is low, since a battery has a lifetime of about 500
charging cycles.
• If you leave your headset battery empty for an extended period of time, it could
excessively discharge the battery. In this case, charge your headset for 10 hours
or more until the battery recovers and recharges completely. Only switch on the
headset once the red indicator light turns off, indicating the battery has fully
recovered.
• Do not let the battery charger remain plugged in the headset for more than 24h.
• The use of any other charger will automatically suspend the warranty.
Pairing the BLUETREK® X2
Before using the BLUETREK® X2 headset, you must pair it with your Bluetooth® mobile
phone. Pairing is the process of linking 2 Bluetooth® devices, so that they can
communicate.
PAGE 3 / 6
To initiate pairing:
1. Place the BLUETREK® X2 and your mobile phone within 0.3 meter (1 foot) from
each other.
2. Switch on your phone and select its Bluetooth® discover mode (refer to the
Bluetooth® mobile phone user manual).
3. When the BLUETREK® X2 is switched off, press and hold the TALK button for
about 7 seconds until the indicator light flashes red and blue alternately. And a
sound can be heard in the speaker.
4. Once the mobile phone detects the headset, a “BLUETREK X2” message will be
displayed. Follow the phone instructions to accept the pairing. The PIN code (or
passkey) is 0000, then press “yes” or “ok”.
If pairing success, the indicator light will switch to blue and flashes slowly.
If you haven’t started the discovery mode within 5 minutes, the headset will switch off.
You must then switch on your headset and start the pairing again.
Wearing the BLUETREK® X2
For your convenience, the ear loops and the ear hook of BLUETREK® X2 are designed
to be removable and can be worn on either ear. BLUETREK®X2, as packaged, is
already with the small ear loop that is specially designed for active outdoor use.
To replace with the ear hook:
Simply unsnap the ear loop from the headset by pulling gently at the base of the ear
clamp ring.
Snap the ear hook onto the headset by applying gentle pressure on the base of the ear
clamp ring.
The ear hook is made of a soft material which can be shaped to fit your ear. Please refer
to the above diagram of how it can be adjusted.
Switching the BLUETREK® X2 ON and OFF
Switching BLUETREK® X2 ON
When your headset is off, press and hold the TALK button for about 2 seconds until the
blue indicator light is on. A beep (2 tones) can be heard in the speaker. Release the
TALK Button.
To check if your headset is ON, press once on the TALK button. If the indicator light
flashes blue, it means your headset is ON.
Switching BLUETREK® X2 OFF
When your headset is on, press and hold the TALK button for about 5 seconds until the
red indicator light is on after the quick blue flashes. A beep (2 tones) can be heard in the
speaker then release the TALK Button.
Making a call
PAGE 4 / 6
*Mobile phone with voice recognition
. Make sure the voice recognition function on your mobile is activated and your voice
tags have been recorded with the phone. To enter these, please refer to your phone’s
manual
. When there is no incoming or active call, press once on the TALK button
. Wait for the audio signal sent by the mobile phone (generally a short tone).
. Speak the name of person you wish to call.
Mobile without voice recognition
. Make sure both the headset and the mobile phone are ON and in stand-by mode.
. Dial the number on the phone keypad, after approximately 2 seconds the audio
connection will be established.
*This function may not be available on some phones, please refer to the trouble
Answering a call
When the headset rings, press once on the TALK button to take the call.
Ending a call
Press once on the TALK button to end an active call.
Adjusting the volume
To increase the volume during an active call, press the “VOL+” button on the headset.
To decrease the volume during an active call, press the “VOL-“ button on the headset.
Muting the microphone
To mute the microphone during an active call
During an active call, press and hold the VOL+ button for approximately 2 seconds. A
periodic tone can be heard in the speaker when the microphone is muted.
To end the mute function
When the microphone is muted quickly press the VOL+ button on the BLUETREK® X2.
The periodic tone will end.
Transferring a call from BLUETREK® X2 to the mobile phone
During an active call, press the TALK button for about 2 seconds.
(This function only works in the Hands-Free Profile.)
In the Headset profile, you can simply turn off your headset.
Transferring a call from the mobile phone to the BLUETREK® X2
To transfer the call back to the headset, use the menu option on your phone.
Call waiting
When you hear a call waiting alert while you are on a call, press once on the TALK
button to accept the second call.
PAGE 5 / 6
This function may not be available, depending on your phone’s functionality. However,
you can always answer the second call from your phone keypad.
Note: This function is not available on some phones. Please refer to the trouble shooting
Additional features with some phones
Rejecting a call
When the headset rings, press the TALK button for about 2 seconds.
Redial the last number
When there is no incoming or active call, press the TALK button for about 2 seconds
until you hear a beep.
Troubleshooting guide
The first thing you should do when encountering a problem that you cannot solve with
this manual, is to switch off your headset and your mobile phone, and switch them on
again.
To find out more, please refer to the trouble shooting frequent asked questions in our
Guidelines for safe use
Read those guidelines before using your headset.
- BLUETREK® X2 is protected against splashing water from all direction, which
means that your headset can function with water falls. Nonetheless, precipitation,
humidity and all types of liquid or moisture may contain minerals that will corrode
electronic circuits. Therefore, if your headset does get wet, dry it completely as
soon as possible.
Warning: never immerse your headset under water.
- Do not drop or try to alter the shape of your headset.
-
-
-
Do not expose your headset to extreme temperatures. Temperature range: 0-40C.
Do not expose your headset to fire or open flames.
Do not try to disassemble your headset. Service and Maintenance can only be
performed by authorized BLUETREK® dealers.
- Do not let children play with your headset, since it contains small parts that could
become detached and create a choking hazard.
-
-
Check the regulation in your area if you plan to use your headset while driving.
Turn off your headset before boarding an airplane.
CAUTION : Danger of explosion if battery is incorrectly replaced. Dispose of batteries
according to local regulations. Do not dispose as household waste.
PAGE 6 / 6
|