Blaupunkt AUGSBURG RCR 87 User Manual

Radio / Cassette  
Augsburg RCR 87  
Essen RCR 127  
Verona RCR 127  
Operating instructions  
Contents  
Quick reference ............................ 21  
Scrolling through the broadcasting  
DSC programming ....................... 33  
networks................................................ 28  
Changing the memory bank ................. 28  
Storing stations ..................................... 28  
Automatically storing the strongest  
stations with Travelstore....................... 29  
Recalling stored stations ...................... 29  
Scanning stored stations with  
Overview of DSC factory settings ........ 35  
Important notes ............................ 24  
Appendix ....................................... 35  
Precautions ........................................... 24  
Traffic safety ......................................... 24  
Installation............................................. 24  
Accessories .......................................... 24  
Second KeyCard................................... 24  
Specifications........................................ 35  
Blaupunkt telephone hotline ................. 36  
Preset Scan .......................................... 29  
Selecting the seek tuning sensitivity .... 29  
Switching from stereo to mono............. 29  
Loudness .............................................. 30  
KeyCard theft protection system 25  
Putting the unit into operation .............. 25  
Removing the KeyCard ........................ 25  
“Training” a second KeyCard/  
Replacing a KeyCard............................ 25  
Displaying the radio pass data ............. 25  
Short Additional Memory (S.A.M.)........ 26  
Turn On Message (T.O.M.) .................. 26  
Optical indication of anti-theft  
Receiving traffic programme  
stations with RDS-EON................ 30  
Traffic announcement priority on/off .... 30  
Beep tone ............................................. 30  
Switching off the beep tone............... 31  
Automatic seek tuning start  
(tape operation) .................................... 31  
Adjusting the volume for traffic  
protection .............................................. 26  
Care of your KeyCard ........................... 26  
Selecting the audio source ......... 26  
announcements and the beep tone...... 31  
Radio operation with RDS ........... 27  
Cassette operation....................... 32  
AF - Alternative frequency .................... 27  
REG - regional programme .................. 27  
Selecting a waveband  
(only Verona RCR 127) ........................ 27  
Station tuning ........................................ 28  
Inserting a tape ..................................... 32  
Ejecting a tape ...................................... 32  
Fast winding.......................................... 32  
Reversing the tape ............................... 32  
Listening to the radio during fast tape  
Automatic tuning  
/
....................... 28  
winding with RM (Radio Monitor) ......... 32  
Care notes ............................................ 33  
Manual tuning with << >>.................. 28  
20  
Quick reference  
Switching on with the ignition being 3 TS / FM (Augsburg RCR 87, Essen  
1 On  
Volume  
Off  
switched off:  
RCR 127)  
To keep on operating the set when the  
ignition is switched off (KeyCard is in-  
serted), proceed as follows:  
Turn the knob to switch the unit off,  
wait for about 2 seconds and turn it on  
again.  
To avoid that the battery goes flat, the  
system will be turned off automatically  
after one hour of playback.  
Selector key to access the memory  
banks I, II and T.  
When switching the set on with the  
knob, the KeyCard has to be inserted.  
The unit will play with the pre-  
adjusted volume.  
TS / BND (Verona RCR 127)  
Selector switch to access the FM  
memory banks I, II and T.  
The wavebands MW and LW can also  
be selected, if “AM ON” is activated in  
the DSC menu.  
Toggling the memory banks:  
Press button.  
The selected memory bank/waveband  
will appear in the display.  
Switching on/off with the KeyCard:  
The set has to be turned on with the  
knob.  
2 SCA / SRC  
SCA – Preset Scan  
Press SCA for about 1 second -  
The stations stored on the preset but-  
tons will be scanned.  
The indicators for the waveband, mem-  
ory bank and preset button will flash in  
the display.  
Notice:  
Travelstore  
Read the information in chapter “Key-  
Card theft protection system”.  
To store and recall the five most pow-  
erful stations with Travelstore.  
To store: Press button for approxi-  
mately 1 sec. until you hear a beep  
and “T-STORE” appears in the display.  
To recall: Select the memory bank “T”  
and press the corresponding preset  
button (1-5) briefly.  
Switching on/off via the ignition:  
When connected correspondingly, the  
set can also be turned on and off with  
the vehicle ignition.  
After the ignition has been switched  
off, a double beep tone will remind you  
that you should remove the KeyCard  
before leaving your vehicle.  
To stop Preset Scan:  
Press SCA again for about 1 second.  
SRC (Source)  
Press SRC briefly –  
You can switch between radio and  
cassette mode, if a cassette is insert-  
ed.  
4 Cassette ejection  
Press  
.
21  
5 Cassette loading slot  
8 1, 2, 3, 4, 5 - preset buttons  
You can store five stations for each of  
the memory banks I, II and T.  
To store a station: Press a preset  
button during radio operation and hold  
down until the set resumes play  
(beep).  
Read also the information in chapter  
“KeyCard theft protection system”.  
Insert the tape with side A or 1 facing  
up, the open side showing to the right.  
Flashing KeyCard tongue  
6 Reversing the tape /  
When the radio is turned off and the  
KeyCard removed, the KeyCard  
tongue can be programmed to flash for  
optical theft protection.  
For more information see chapter  
“DSC programming”.  
Fast winding  
Reversing the tape/fast winding  
Press both buttons at a time.  
TR1 or TR2 will be displayed.  
To recall a station: Select the desired  
memory bank and press the relevant  
preset button briefly.  
This flashlight can be switched off by  
pushing in the tongue and lock.  
“WRONG KC” will briefly appear on  
the display and the set will switch off  
automatically.  
Verona RCR 127:  
You can also store 5 stations for the  
AM and LW waveband.  
Fast winding  
FR : fast rewind, press FF to stop  
FF : fast forward, press FR to stop  
9 KeyCard theft protection system  
To operate the set it is necessary that  
the KeyCard is inserted.  
7 AF / TA  
AF Alternative frequency in RDS  
mode:  
When “AF” is displayed, the radio’s  
RDS module is searching for a fre-  
quency offering the same programme  
in a better quality.  
AF on/off: press button for about  
1 second.  
KeyCard  
Inserting the KeyCard  
With the KeyCard tongue sticking out  
of the unit, introduce the KeyCard into  
the slot with the contact area show-  
ing up.  
To remove the card, press first to un-  
lock.  
TA (Traffic Announcement = priority  
for traffic stations)  
If “TA” is displayed, the radio will play  
traffic stations only.  
Priority on/off: press button briefly.  
22  
: Display  
; Rocker switch  
< AUD  
To adjust the treble, bass, balance and  
Radio operation  
fader.  
a
If the display shows “TRE” or “BAS”,  
you can adjust the reproduction of the  
treble and bass frequencies with the  
rocker switch. If “BAL” or “FAD” is dis-  
played, you can set the balance (left/  
right) and fader (front/rear).  
c d e  
f g h i  
b
Briefly press AUD as many times as  
required and make the setting using  
the rocker switch.  
/
Station search  
Up  
Down  
a) NDR1 NDS - Station name  
b) TR 1  
- Track (side) 1 of the cas-  
sette  
- Waveband  
<</>> Up/Down in short intervals  
(on FM only if AF is off)  
c) FM  
d) I, II, T  
- Memory bank I, II or  
Travelstore  
- Preset button (1-5)  
- Alternative frequency for  
RDS operation  
On FM only:  
e) 5  
f) AF  
<</>> To scroll through the station net-  
works when AF is on, e.g.NDR 1, 2,  
3, 4, N-JOY, FFN, ANTENNE ... .  
Treble + / Fader front  
Treble – / Fader rear  
g) TP  
- A traffic station is being  
received  
Extra rocker switch functions:  
Further setting functions with  
h) TA  
i) LD  
- Priority for traffic stations  
- Loudness on  
Bass – / Balance left  
Bass + / Balance right  
AUD  
DSC Mode  
<
<
The last setting will be stored automat-  
ically.  
To switch off AUD: Press button briefly  
again.  
Condition: The corresponding function  
is activated.  
If the setting remains unchanged with-  
in 8 seconds, the display will switch  
back to the previous condition.  
23  
Important notes  
Extra function AUD  
Installation  
Precautions  
Loudness - When listening at a low  
level, the Loudness function creates a  
more natural sound by boosting  
the low frequency range.  
Loudness on/off: Press AUD for ap-  
proximately 1 sec.  
“LD” lights up in the display if the  
Loudness function is switched on.  
Please refer to chapter “DSC program-  
ming” for more information on how to  
program the Loudness boost.  
If you would like to install your new car ster-  
eo yourself or add other audio components  
to existing ones, then please read carefully  
the enclosed instructions on installation and  
connection.  
In order to ensure that the set operates prop-  
erly it is necessary that the positive power  
supply line is connected to the ignition and  
the permanent +12 V lead.  
Before starting to use your new car radio,  
please read the following information care-  
fully.  
Traffic safety  
Traffic safety always has the highest priori-  
ty.  
As the driver of a motor vehicle, it is your  
responsibility to pay attention to the traffic  
situation at all times. Never use your car  
radio in a way that could distract you.  
Please keep in mind that you travel a dis-  
tance of 14 m per second at a speed of only  
50 km/h.  
Should the traffic situation become particu-  
larly demanding, we advise you not to use  
the radio.  
Always make sure that you are still able to  
hear any warning signals coming from out-  
side of the vehicle, such as police or fire  
engine sirens, so that you can react accord-  
ingly.  
Therefore, you should always select a mod-  
erate volume for playing your car radio while  
you are driving.  
Do not ground the loudspeaker outputs!  
Accessories  
= DSC (Direct Software Control)  
Use the DSC function to customise  
certain programmable, basic settings  
to suit your personal needs and prefer-  
ences. See chapter “DSC program-  
ming” for more information.  
Use only the accessories and spare parts  
approved by Blaupunkt.  
Second KeyCard  
You can also operate your car radio with a  
second KeyCard.  
Refer to chapter “KeyCard theft protection  
system” for more information.  
You can purchase a second KeyCard at any  
specialised dealership.  
24  
KeyCard theft protection system  
This piece of equipment is supplied with one The system will switch off after approximate-  
KeyCard, though you can also operate the ly 10 seconds.  
Push in the KeyCard. The card is re-  
leased and put in the proper position  
for being removed.  
set with a second KeyCard.  
When inserting another card type (e.g.  
If you have lost your KeyCard or if it was phone or credit card), the display will show  
damaged, you can buy a second / extra card “WRONG KC” for approximately 2 seconds.  
Remove the first KeyCard and insert  
the new one.  
from your specialised dealer.  
The set will switch off automatically.  
After the display indication “READY” or  
“LEARN KC”,  
When using a second KeyCard, the settings Remove the wrong card and introduce the  
stored on the first card will be adopted. How- correct KeyCard.  
press DSC.  
ever, you can individually store the follow-  
ing functions:  
Turn the knob to switch on the set.  
Now you can also use the new KeyCard for  
operating your unit.  
A maximum of two cards can be used for  
the set.  
When trying to “train” a third one, the ac-  
cess authorisation for the KeyCard not used  
for the “training” process will be deleted au-  
tomatically.  
Bass, treble, balance and fader settings,  
Loudness, TA (traffic announcement vol-  
ume), beep volume, lo or dx.  
Removing the KeyCard  
Never pull out the KeyCard directly!  
In addition, the settings activated before  
switching the radio off, such as the station  
tuned in, TA priority, AF, AM ON/OFF and  
RM ON/OFF will also remain stored.  
This ensures that you will find your basic  
settings re-adjusted automatically as soon  
as you have inserted your KeyCard.  
First, slightly push in the KeyCard.  
This releases the card and puts it in the prop-  
er position for being removed.  
Now you can pull it out.  
Displaying the radio pass data  
“Training” a second KeyCard/  
Replacing a KeyCard  
Using the KeyCard supplied with your set  
you can have the radio pass data such as  
the model name, product number (7 6..) and  
serial number indicated on the display pan-  
el.  
Putting the unit into operation  
While operating the unit with the first Key-  
Card, you can “train” a second one to be  
also used with the set:  
Turn on the set.  
With the KeyCard tongue sticking out,  
introduce the KeyCard into the slot  
with the contact area showing up.  
Please refer to chapter “DSC programming  
- READ KC”.  
Insert the first KeyCard and turn on the  
set.  
Press the DSC button and select  
The car radio is now ready for operation.  
If a wrong KeyCard is inserted, then “CARD  
ERR” followed by “WAIT” will appear in the  
display. In this case please do not make any  
further adjustments.  
“LEARN KC” with  
/
.
Press << or >>.  
The display will switch to “CHANGE”.  
25  
Selecting the audio source  
Short Additional Memory  
(S.A.M.)  
Optical indication of anti-theft  
protection  
Using the SRC button you can switch be-  
tween radio and tape operation.  
Tape operation is only available if a cassette  
is inserted.  
Using the second KeyCard to be purchased Flashing KeyCard tongue  
at any specialised dealership, you can pro-  
When the vehicle is stationary and the Key-  
To switch to another source,  
gram a short text by selecting the DSC menu  
item READ KC. This text will be moved  
through the display and might be the tele-  
phone number of a car repair service or the  
emergency call number of your auto club.  
Any specialised dealer with the proper  
equipment can program the desired text with  
up to a maximum of 162 characters onto the  
KeyCard.  
Card removed, the KeyCard tongue can be  
switched to flash for extra anti-theft securi-  
ty.  
For this it is necessary that the positive pow-  
er supply line and the permanent +12 V lead  
are connected such as described in the in-  
stallation instructions.  
press SRC briefly.  
Be sure that “LED ON” is adjusted in the  
DSC mode.  
If required, please refer to chapter “DSC  
programming - LED”.  
Turn On Message (T.O.M.)  
Using the second KeyCard to be purchased  
at any specialised dealership, you can pro-  
gram the unit to display a selected “Turn On  
Message” after the set is switched on.  
Any specialised dealer with the proper  
equipment can program the desired text with  
up to a maximum of 48 characters onto the  
KeyCard.  
Switching off the flashlight  
The flashlight can be switched off by push-  
ing in the KeyCard and lock.  
If you would like to deactivate the flashing  
tongue with general effect, adjust the rele-  
vant item in the DSC menu to “LED OFF”.  
Each time you switch on your car radio us-  
ing the second KeyCard, this text will ap-  
pear in the display.  
Care of your KeyCard  
In order to ensure that the KeyCard always  
functions correctly, it is important for the  
contacts to be free from any foreign parti-  
cles. Avoid direct skin contact.  
If necessary, clean the KeyCard contacts  
using a cotton swab dipped in alcohol.  
26  
Radio operation with RDS (Radio Data System)  
The Radio Data System offers you more If “SEARCH” appears in the display when You can select REG ON or REG OFF in the  
convenience when listening to FM radio sta- switching on the radio or recalling one of the DSC menu. For more information, refer to  
tions.  
stored frequencies, the unit is automatically chapter “DSC programming - REG ON/  
More and more radio stations have begun searching for an alternative frequency.  
to broadcast RDS information alongside “SEARCH” will disappear from the display  
OFF”.  
their programmes.  
when the alternative frequency has been Selecting a waveband  
As soon as programmes have been identi- found or after the frequency band has been (only Verona RCR 127)  
fied, the station name including a regional run through completely.  
identifier, if applicable, will appear in the dis- If the reception quality of the selected pro-  
play, for example, NDR1 NDS (regional pro- gramme becomes too bad:  
gramme in Lower Saxony, Germany).  
When RDS is activated, the preset buttons  
become programme buttons. You now know  
exactly which programme you have tuned  
into, making it easy to find the desired sta-  
tion quickly.  
You can select between the following wave-  
bands:  
FM 87.5 - 108 MHz  
MW 531 - 1602 kHz  
LW 153 - 279 kHz  
Tune into another station.  
REG - regional programme  
Press TS/BND until the desired wave-  
band shows on the display panel.  
Certain radio programmes are split up at  
times into regional programmes offering lo-  
cal information. The 1st programme broad-  
cast by NDR, for example, offers pro-  
grammes with different contents in the north-  
ern states of Germany Schleswig-Holstein,  
Hamburg and Lower Saxony at certain times  
of the day.  
If you have tuned to a regional programme,  
you can select between REG ON and REG  
OFF:  
REG ON – the radio keeps tuned to the cur-  
rent regional programme, even if the recep-  
tion quality is getting poorer.  
Notice:  
But RDS offers you further advantages:  
In the DSC menu you can deactivate the  
station selection on either MW or LW or for  
both wavebands at the same time.  
This has the advantage that only the re-  
quired bands will allow to be activated, so  
that you must press the TS/BND button less  
often. For more information, please refer to  
chapter “DSC programming - AM ON/AM  
OFF”.  
AF - Alternative frequency  
The AF (Alternative Frequency) function  
makes sure that the strongest frequency of  
the currently selected programme is always  
tuned in automatically.  
This function is activated when “AF” appears  
in the display.  
In order to switch this function on or off,  
press AF/TA for about 1 second.  
REG OFF – the radio automatically tunes  
to the regional programme offering the best  
reception quality (but maybe with local in-  
formation for another service area).  
While searching for the strongest reception  
signal, the radio may switch to mute briefly.  
27  
Station tuning  
Manual tuning:  
Changing the memory bank  
Press << >>. The frequency will  
change in short intervals in downwards  
or upwards direction.  
Automatic tuning  
/
You can shift between the memory banks I,  
II and T in order to store stations and recall  
them later.  
The currently selected memory bank is in-  
dicated in the display.  
Press  
cally search for the next station.  
When keeping the upper or lower part  
/
; the car radio will automati-  
When holding the right or left part of the rock-  
er switch depressed, the frequency scan is  
speeded up.  
/
of the rocker switch depressed, seek tuning  
will speed up in upwards or downwards di-  
rection.  
Press the TS/FM or TS/BND button as  
many times until the desired memory  
bank lights up in the display.  
Scrolling through the broadcast-  
ing networks  
You can use the << >> buttons to tune in Storing stations  
stations of your reception area.  
On FM, you can store five stations on the  
preset buttons 1, 2, 3, 4, 5 for each of the  
memory banks I, II and T.  
On MW/LW, you can also store five stations  
each (only with Verona RCR 127).  
If several programmes of the broadcasting  
networks can be received, you can scroll  
through them in forwards direction pressing  
>>, or backwards using the << button, e.g.  
NDR 1, 2, 3, 4, N-JOY, FFN, ANTENNE ...  
For this it is necessary that the stations have  
been tuned in at least once and that “AF” is  
active (lights up in the display).  
Seek tuning  
Up  
Down  
Select the desired memory bank.  
<< / >> Up/Down in short intervals  
(FM only, “AF” must be switched off)  
Tune in a station with the rocker switch  
(either automatically or manually).  
For this purpose, start automatic tuning, e.g.  
using Travelstore:  
Press and hold down the desired pre-  
set button until the radio resumes play  
after the muting (takes approximately 1  
sec., confirmed by beep).  
Manual tuning with << >>  
You can also tune in a station manually.  
Press TS/FM or TS/BND for 1 sec.; the  
system starts to run through the fre-  
quency band. The display shows “T-  
STORE”.  
Condition:  
AF must be switched off (i.e. the symbol  
does not light up in the display).  
Now the station has been stored.  
The activated preset button is indicated in  
the display.  
If necessary, deactivate AF:  
If “AF” does not light up,  
• press AF/TA for approximately 1 sec.  
Press AF/TA for about 1 second.  
This fulfils the requirements for selecting  
stations with << >>.  
28  
Notice:  
Recalling stored stations  
Selecting the seek tuning sensi-  
tivity  
Should you tune in a station which has al-  
ready been stored before, then the corre-  
sponding preset position will briefly flash in  
the display.  
You can recall any stored station at the touch  
of a button.  
You can alter the automatic seek tuning  
sensitivity.  
If “lo” is displayed, the radio will only pick up  
strong, local stations.  
If “lo” does not light up, the radio will also  
pick up weaker, distant stations.  
Should you wish to alter the seek tuning  
sensitivity, refer to chapter “DSC program-  
ming – LO/DX”.  
Select the memory bank with TS/FM or  
TS/BND.  
Press the corresponding preset button  
briefly to recall the station.  
Automatically storing the  
strongest stations with Travel-  
store  
Scanning stored stations with  
Preset Scan  
You can automatically store the five most  
powerful FM stations of your current recep-  
tion area sorted according to their signal  
You can have all of the stored stations briefly  
strength. This function is particularly conven- scanned.  
ient on longer trips.  
Stereo - mono switching  
To start Preset Scan:  
The radio will only play in stereo if the ster-  
eo quality of the received station signal is  
sufficient. When the signal strength gets  
poor, the radio will gradually switch to mono.  
You can select between stereo or mono  
sound in the DSC menu.  
Press the TS/FM or TS/BND button for  
1 sec.  
Press SCA/SRC for approximately  
1 sec. until “SCAN” appears in the dis-  
play.  
“T-STORE” will appear in the display.  
The five strongest FM stations will be auto-  
All of the stored stations to be received in  
matically stored on the memory bank “T” the selected waveband will be scanned one  
For more information, refer to chapter “DSC  
programming – STEREO/MONO”.  
Each time the radio is switched on, stereo  
sound is activated automatically.  
(Travelstore). When this process has been  
completed, the radio will play the first sta-  
tion stored on preset 1.  
If desired, stations can also be stored man-  
ually on the Travelstore bank (see “Storing  
stations”).  
after the other. On FM, the radio will either  
scan the stations stored on memory bank I  
and II or T.  
To select a scanned station and switch  
off Preset Scan:  
Press SCA/SRC for about 1 second.  
Note:  
If “TA” shows on the display panel, the sys-  
tem will scan the stored traffic stations only.  
29  
Receiving traffic programme stations with RDS-EON  
Loudness  
EON stands for Enhanced Other Networks, Traffic announcement priority  
meaning the exchange of information with- on/off  
Adjusts the low bass frequencies for a more  
natural sound.  
in a radio network.  
If the priority for traffic announcement pro-  
Many FM broadcasters offer traffic messag-  
grammes is activated, “TA” will light up in  
es for their service area at regular intervals.  
the display.  
Switching Loudness on/off:  
Press the AUD button for approximate-  
All traffic programme stations transmit a  
special carrier signal alongside their pro-  
To switch the priority on or off:  
ly 1 sec.  
Press the AF/TA button.  
grammes, which is decoded by your car ra-  
When the Loudness function is active, “LD”  
will light up in the display.  
dio. If this signal is identified, “TP” will ap- When pressing AF/TA while a message is  
See chapter “DSC programming” for more pear in the display (Traffic Programme).  
being broadcast, this message will be inter-  
rupted. The unit will then switch back to the  
previous condition. The priority for all other  
In addition to these, there are also stations  
which do not actually transmit traffic pro-  
information.  
grammes themselves, but by using RDS- traffic messages remains active.  
EON they offer the possibility to receive the  
traffic messages broadcast by another traf-  
Please note that several buttons have no  
function while a traffic announcement is  
fic programme station in the same radio broadcast.  
network.  
If you wish to have the priority for traffic an-  
nouncements activated while listening to  
Beep tone  
If you leave the reception area of the traffic  
one of these stations (e.g. NDR3), “TA” must  
appear on the display panel.  
programme station currently tuned into, you  
will hear a beep tone approximately every  
30 seconds.  
This tone will also be released when press-  
ing a preset button which has no traffic pro-  
gramme allocated to it.  
If a traffic announcement is broadcast, the  
radio will automatically switch to the linked  
traffic programme station (in this case,  
NDR2) for the duration of the message and  
return to the original programme (NDR3)  
afterwards.  
30  
Switching off the beep tone  
Adjusting the volume for traffic  
announcements and the beep  
tone  
a) Tune into another station offering traf-  
fic information:  
This volume was preset at the factory,  
though you can alter the value using the  
DSC function (see “DSC programming – TA  
VOL”).  
You can also change the announcement and  
beep volume for the current message only.  
Press the rocker switch or  
press a preset button which has a  
traffic programme station allocated  
to it.  
Alternatively:  
b) Switch off the priority for traffic an-  
nouncements:  
Decreasing the volume:  
Press AF/TA briefly.  
Press AF/TA.  
“TA” will disappear from the dis-  
play.  
The usual volume boost is now disabled and  
you can alter the volume as desired. The  
priority is deactivated for the current mes-  
sage only.  
Automatic seek tuning start  
(tape operation)  
Increasing the volume:  
Turn the knob 1  
.
When leaving the reception area of the tuned  
in traffic programme station while listening  
to a tape, the system will automatically start  
searching for a new TA programme.  
If no such station is found within approxi-  
mately 30 seconds, you will hear a warning  
beep every 30 seconds. To switch off the  
beep tone proceed as described above.  
31  
Cassette operation  
To stop fast forward  
press FR.  
Notice:  
The car stereo has to be switched on.  
If there is too much tension on the tape dur-  
ing playback, the set may reverse the direc-  
tion by itself before having reached the end  
of the tape side. In this case check the con-  
dition of the cassette tape. Sometimes it  
helps to rewind it completely.  
The unit will automatically switch to tape  
operation when inserting a cassette.  
Fast rewind  
Press FR (fast rewind).  
Inserting a tape  
At the beginning of the tape the unit  
will start playback automatically.  
Turn on the set.  
Insert a tape.  
To stop fast rewind  
Listening to the radio during fast  
tape winding with RM (Radio  
Monitor)  
Track A or 1 will be played.  
press FF.  
During cassette operation, “TR 1” or “TR 2”  
(track) will appear in the display.  
Fast winding  
FR : fast rewind - press FF to stop.  
FF : fast forward - press FR to stop.  
During fast winding of the tape, i.e. when  
the radio is normally muted, you can use  
the RM function to listen to the radio.  
Insert the tape with side A or 1 facing up, the  
open side showing to the right.  
For more information please refer to chap-  
ter “DSC programming – RM ON/OFF”.  
Reversing the tape  
Press both buttons at a time.  
TR1 or TR2 will appear in the display.  
Ejecting a tape  
Press  
The cassette will eject.  
.
Reversing the tape  
To switch to the other side of the tape dur-  
ing playback,  
Fast winding  
press FR and FF simultaneously.  
Fast forward  
At the end of the tape the unit will automat-  
ically reverse to the other side (autoreverse).  
The display shows “TR 1” for track (side) 1  
or “TR 2” for track 2.  
Press FF (fast forward).  
At the end of the tape the unit will au-  
tomatically reverse the direction and  
start playing the other side.  
32  
DSC programming  
Care notes  
Refer to “Radio operation  
with RDS / REG - regional  
programme”.  
DSC (Direct Software Control) allows you  
to customise certain programmable, basic  
settings to suit your personal needs and  
preferences and then store them.  
The basic settings for this audio equipment  
were made at the factory.  
In the following you can find an overview of  
these settings, so that you can always reset  
to these if desired.  
To avoid possible problems, we recommend  
you to use C-60/C-90 type cassette tapes  
only. Store your tapes in a cool place away  
from dirt, dust and temperatures exceeding  
50 °Celsius. Allow very cold tapes to warm  
up before playing them in order to avoid  
uneven tape transport. After approximately  
100 hours of use, dust particles collected  
on the playback head or roller may lead to  
tape run problems and sound distortions.  
Use a head cleaning tape to remove nor-  
mal dirt build-up. For tougher cases, use a  
cotton swab (Q-Tip) dipped in alcohol. Do  
not attempt to clean by inserting a hard ob-  
ject into the player!  
RM ON/OFF (Radio Monitor)  
Allows you to listen to the  
radio during fast winding of  
the tape.  
RM ON – Radio playback  
activated.  
If you wish to alter any of the programming,  
press SCA/SRC to select one of the  
operating modes radio or cassette  
(cassette must be inserted).  
RM OFF – Function deacti-  
vated.  
press DSC.  
READ KC  
To read out the KeyCard  
data.  
Use the rocker switch to select and adjust  
the functions described in the following. The  
display will show you the adjusted condition.  
The KeyCard supplied with  
the radio is used to display  
the model name, type  
number (7 6..) and the serial  
number.  
Using the second KeyCard  
to be purchased at any spe-  
cialised dealership it is pos-  
sible to display the Short  
Additional Memory (S.A.M.)  
data entered by the dealer.  
See chapter “Short Addition-  
al Memory S.A.M.”.  
/
Select function  
Adjust/recall value  
<< >>  
REG ON/OFF REG ON – regional function  
is switched on.  
REG OFF – regional func-  
tion is switched off.  
33  
LEARN KC To “train” a second Key-  
Card.  
volume adjusted for the pro- LO/DX  
gram is lower.  
If the program volume is  
higher than the TA VOL lev-  
el, the traffic report will be  
played slightly louder.  
To adjust the seek tuning  
sensitivity for local or distant  
stations.  
Please read the information  
in chapter “KeyCard theft  
protection system - Training  
a second KeyCard”.  
LO - local stations  
LO 1 - high sensitivity  
LO 3 - normal sensitivity  
DX - distant stations  
DX 1 - high sensitivity  
DX 3 - normal sensitivity  
LED ON/OFF You can choose between  
LED ON or LED OFF. With  
LED ON, the KeyCard  
LOUDNESS When listening at a low lev-  
el, the Loudness function  
creates a more natural  
sound by boosting the low  
frequency range.  
LOUD 1 - Low boost  
LOUD 6 - Max. boost  
You can select separate sen-  
sitivity levels for AM and FM.  
tongue will flash for extra  
anti-theft protection when  
the unit has been switched  
off and the KeyCard re-  
moved.  
To quit the DSC programming mode  
and store the adjustment:  
Press DSC.  
STEREO/MONO  
The DSC programming mode will be auto-  
matically quit 8 seconds after having made  
the last adjustment.  
BEEP  
Acknowledgement tone for  
all functions which require a  
button to be pressed for  
more than 1 second.  
The volume can be adjusted  
from between 0 to 9.  
(0 = off)  
You can select between  
stereo or mono sound.  
AM ON/OFF (Verona RCR 127)  
You can deactivate one or  
both AM bands (MW/LW) in  
order to reduce the number  
of bands for selection with  
TS/BND.  
TA VOL  
To adjust the traffic an-  
nouncement and beep tone  
volume from between 0 to  
63.  
The message will then come  
through at this volume, if the  
selectable:  
AM ON – all bands  
MW OFF – LW, FM  
LW OFF – MW, FM  
AM OFF – FM  
34  
Appendix  
Overview of DSC factory set-  
tings  
FM sensitivity: 1.0 µV at 26 dB  
Specifications  
signal-to-noise ratio  
Amplifier  
REG  
RM  
READ KC  
LEARN KC  
LED  
BEEP  
TA VOL  
LOUDNESS  
OFF  
OFF  
-
-
ON  
4
35  
3
Output power: 4 x 23 W RMS power  
acc. to DIN 45324 at  
14.4 V  
FM frequency response:  
35 - 16 000 Hz  
4 x 35 W max. power  
Tape player  
Frequency response:  
40 - 15 000 Hz  
Augsburg RCR 87:  
4 x 19 W RMS power  
acc. to DIN 45324 at  
14.4 V  
STEREO  
1
DX  
4 x 20 W max. power  
(Verona RCR 127):  
AM ON  
Tuner  
Wavebands:  
FM  
:
87.5 – 108 MHz  
(only Verona RCR 127)  
MW 531 – 1602 kHz  
LW  
153 – 279 kHz  
Subject to modifications!  
35  
Blaupunkt  
telephone hotline  
Address of the next service  
centre in your vicinity  
(only for Germany)  
If you would like to know the address of  
the next Blaupunkt service centre of  
your area without having our service list  
at hand:  
-
-
Find out your area code.  
Then call the following chargeable  
phone number: 01 80 / 5 25 56 66.  
-
Using the area code to be entered  
you will be automatically given the  
address and phone number of the  
next Blaupunkt service centre. You  
can also request this information  
by fax.  
36  
Blaupunkt-Werke GmbH  
Bosch Gruppe  
12/96 Pf  
K7/VKD 8 622 400 990  

Advent MITBTSW2 User Manual
Belkin 8820tt00529 F4U037 User Manual
Canon MV 30 User Manual
Canon Optura 200 MC User Manual
Canon Z 505 User Manual
Dell Car Speaker T5SA User Manual
JBL GTO963 User Manual
JVC Camcorder Accessories GY HM150U User Manual
JVC Car Amplifier KS AX3102 User Manual
JVC GR D750U User Manual