Black Box Cable Box Zone 4 Seismic Cabinets, 45U User Manual

RM5100A  
RM5110A  
Zone 4 Seismic Cabinets, 45U  
These 40" deep and 32" deep cabinets meet  
Zone 4 seismic requirements.  
Hold up to 2500 pounds of equipment.  
Order toll-free in the U.S.: Call 877-877-BBOX (outside U.S. call 724-746-5500)  
FREE technical support 24 hours a day, 7 days a week: Call 724-746-5500 or fax  
724-746-0746 • Mailing address: Black Box Corporation, 1000 Park Drive, Lawrence,  
PA 15055-1018 • Web site: www.blackbox.com • E-mail: [email protected]  
Customer  
Support  
Information  
Table of Contents  
Table of Contents  
1. Specifications ......................................................................................... 4  
2. Overview .............................................................................................. 6  
2.1 Introduction ..................................................................................... 6  
2.2 Features............................................................................................ 6  
2.3 What‘s Included............................................................................... 7  
2.4 What You Need to Supply ............................................................... 7  
2.5 Hardware Description....................................................................... 8  
3. Installing the Mounting Plates in the Cabinet............................................ 9  
4. Troubleshooting........................................................................................11  
4.1 Contacting Black Box ......................................................................11  
4.2 Shipping and Packaging..................................................................11  
Page 3  
724-746-5500 | blackbox.com  
Chapter 1: Specifications  
1. Specifications  
Cable Entry Ports — (2) on top of cabinet with caps and grommets  
Exterior Height — 84.05" (213.5 cm)  
Exterior Width — 27.55" (70 cm)  
Exterior Depth — RM5100A: 39.37" (100 cm);  
RM5110A: 31.5" (80 cm)  
Finish — RAL 9005 textured low-gloss black polyester powder paint coating  
inside and out; smoke gray acrylic window in reinforced front door  
Frame — Heavy gauge welded steel frame with (6) rack angle mounting struts  
Interior Width — 19" (48.3 cm)  
Number of Fan Cutouts — (2) with finger guards  
Rack Angle Holes — RM5100A: M6 square;  
RM5110A: 10-32 tapped  
Rack Units — 45U  
Standards — NEBSTelcordia GR-63-CORE Zone 4: Tested with 1000 lb.  
(453.6 kg) of equipment installed and 100 lb. (45.4 kg) of simulated cable  
weight on the top; Meets California Building Code (CBC) requirements  
Weight Capacity — Dynamic: 1100 lb. (499 kg);  
Static: 2500 lb. (1134 kg)  
Page 4  
724-746-5500 | blackbox.com  
Chapter 1: Specifications  
Figure 1-1. Top dimensions.  
Figure 1-2. Front and side dimensions.  
Page 5  
724-746-5500 | blackbox.com  
Chapter 2: Overview  
2. Overview  
2.1 Introduction  
The Zone 4 Seismic Cabinet protects servers, networking equipment, and  
telephony equipment through Zone 4 seismic activity. It’s made of heavy-gauge  
welded steel and supports up to 2500 pounds (1134 kg) of equipment. The  
cabinet is also ideal for use in high vibration areas or areas with high load  
capacities. It conforms to EIA standards for 19" equipment mounting. Use it in  
different applications with 19-inch rackmount equipment and fans.  
The top of the cabinet features two cable entry ports with caps and grommets,  
and two fan-ready cutouts with finger guards. With its “chimney” effect, the  
cabinet cools mounted equipment by drawing cool air through louvers and  
venting the heated air through the top.  
Two models are available:  
• RM5100A: 39.37" deep Zone 4 Seismic Cabinet with M6 square mounting rails  
• RM5110A: 31.5" deep Zone 4 Seismic Cabinet with 10-32 tapped mounting rails  
Mounting hardware is not included.  
2.2 Features  
• Both front and rear doors are hinged left and equipped with keylock flush  
handle and three-point latching.  
• Same key provides access to all doors and side panels.  
• Doors and side panels can be removed for easier equipment installation and  
upgrades.  
• Vented, heavy gauge steel base is designed to bolt to floor with seismic-rated  
fasteners.  
• Has louvers on lower 13 of rear door for ventiliation.  
• The cabinet ships fully assembled.  
Page 6  
724-746-5500 | blackbox.com  
Chapter 2: Overview  
2.3 What’s Included  
RM5100A:  
• 84.05"H x 27.55"W x 39.37"D Zone 4 Seismic Cabinet  
• (2) sets of painted rack angles with M6 holes per EIA spacing (58" x 58" x 12")  
• (4) mounting plates  
• This user‘s manual  
RM5110A:  
• 84.05"H x 27.55"W x 31.5"D Zone 4 Seismic Cabinet  
• (2) sets of painted rack angles with 10-32 tapped holes per EIA spacing (58" x  
5
8" x 12")  
• (4) mounting plates  
• This user‘s manual  
2.4 What You Need to Supply  
12" high-strength mounting hardware  
Page 7  
724-746-5500 | blackbox.com  
Chapter 2: Overview  
2.5 Hardware Description  
Figure 2-1 shows the components of the cabinets.  
Figure 2-1. Cabinet components.  
Page 8  
724-746-5500 | blackbox.com  
Chapter 3: Installing the Mounting Plates in the Cabinet  
3. Installing the Mounting Plates in the Cabinet  
The cabinet ships fully assembled, but you will need to use the (4) mounting  
plates (included) with 12" high-strength mounting hardware (not included) to  
install equipment in the cabinet.  
Figure 3-1. Mounting plates (1, included) and hardware (2, not included).  
Page 9  
724-746-5500 | blackbox.com  
Chapter 3: Installing the Mounting Plates in the Cabinet  
Figure 3-2 shows how to install the mounting plates in the cabinet.  
Figure 3-2. Installing the mounting plates in the cabinet.  
Page 10  
724-746-5500 | blackbox.com  
Chapter 4: Troubleshooting  
4. Troubleshooting  
4.1 Contacting Black Box  
If you determine that your cabinet is malfunctioning, do not attempt to alter or  
repair the unit. It contains no user-serviceable parts. Contact Black Box Technical  
Support at 724-746-5500 or [email protected].  
Before you do, make a record of the history of the problem. We will be able to  
provide more efficient and accurate assistance if you have a complete description,  
including:  
• the nature and duration of the problem.  
• when the problem occurs.  
• the components involved in the problem.  
• any particular application that, when used, appears to create the problem or  
make it worse.  
4.2 Shipping and Packaging  
If you need to transport or ship your cabinet:  
• Package it carefully. We recommend that you use the original container.  
• If you are returning the unit, make sure you include everything you received  
with it. Before you ship for return or repair, contact Black Box to get a Return  
Authorization (RA) number.  
Page 11  
724-746-5500 | blackbox.com  
Black Box Tech Support: FREE! Live. 24/7.  
Tech support the  
way it should be.  
Great tech support is just 30 seconds away at  
724-746-5500 or blackbox.com.  
About Black Box  
Black Box provides an extensive range of networking and infrastructure products.  
You’ll find everything from cabinets and racks and power and surge protection  
products to media converters and Ethernet switches all supported by free, live 24/7  
Tech support available in 30 seconds or less.  
© Copyright 2012. Black Box Corporation.  
RM5100A, version 1  
724-746-5500 | blackbox.com  

Audiovox Mobile Video VOD128 User Manual
Baxi Potterton Performa 24 Eco HE User Manual
Belkin BLUETOOTH HOT SYNC OPERATION NZ90 User Manual
Boss Audio Systems Car Video System BV9996B User Manual
Braun MR 505 M User Manual
Clarion OHM 642 OHM642 User Manual
Hypertec Messenger N11598PHY User Manual
Hypertec N7828AHY User Manual
JL Audio C3 525 User Manual
JVC CH X series User Manual