INSTRUCTION MANUAL
MANUAL DE INSTRUCCIONES
Model Number/ No. De Modelo:
Beer Dispenser
BD7000
Dispensador / Enfriador de Cerveza
BEFORE USE, PLEASE READ AND FOLLOW ALL SAFETY RULES AND OPERATING
INSTRUCTIONS.
La sección en español empieza en la página 23.
Avanti has a policy of continuous improvement on its products and reserves the right to change
materials and specifications without notice.
Avanti Products, A Division of The Mackle Co., Inc.
P.O. Box 520604 - Miami, Florida 33152
BEER DISPENSER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages in this manual for your appliance. Always read
and obey all safety messages.
This is the Safety Alert Symbol. This symbol alerts you to potential hazards that
can kill or injure you and others. All safety messages will follow the Safety
Alert Symbol and either the words” DANGER”, “WARNING” or “CAUTION”.
Danger means that failure to heed this
safety statement may result in severe
personal injury or death.
Warning means that failure to heed this
safety statement may result in extensive
product damage, serious personal injury, or
death.
Caution means that failure to heed this
safety statement may result in minor or
moderate personal injury, property or
equipment damage.
All safety messages will alert to know what potential hazard is, tell you how to reduce the chance of
injury, and let you know what can happen if the instructions are not followed.
3
IMPORTANT SAFEGUIDES
Before the appliance is used, it must be properly positioned and installed as
described in this manual,so read the manual carefully. To reduce the risk of fire,
electrical shock or injury when using the appliance, follow basic precaution,
including the following:
Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and
do not use an extension cord.
Replace all panels before operating.
It is recommended that a separate circuit, serving only your appliance be provided. Use
receptacles that cannot be turned off by a switch or pull chain.
Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or
explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance. The fumes can create a fire hazard or explosion.
Before proceeding with cleaning and maintenance operations, make sure the power line of the
unit is disconnected.
Do not connect or disconnect the electric plug when your hands are wet.
Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result
in electrical shock or death.
Do not attempt to repair or replace any part of your appliance unless it is specifically
recommended in this manual. All other servicing should be referred to a qualified technician.
FOLLOW WARNING CALL OUTS BELOW ONLY WHEN APPLICABLE TO YOUR MODEL
Use two or more people to move and install appliance. Failure to do so can result in back or other
injury.
To ensure proper ventilation for your appliance, the front of the unit must be completely
unobstructed. Choose a well-ventilated area with temperatures above 60°F (16°C) and below
90°F (32°C). This unit must be installed in an area protected from the element, such as wind, rain,
water spray or drips.
The appliance should not be located next to ovens, grills or other sources of high heat.
The appliance must be installed with all electrical, water and drain connections in accordance with
state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in
accordance with the National Electrical Code and local codes and ordinances is required.
Do not kink or pinch the power supply cord of appliance.
The fuse (or circuit breaker) size should be 15 amperes.
It is important for the appliance to be leveled in order to work properly. You may need to make
several adjustments to level it.
All installation must be in accordance with local plumbing code requirements.
Make certain that the pipes are not pinched or kinked or damaged during installations.
Check for leaks after connection.
Never allow children to operate, play with or crawl inside the appliance.
If you use the drainage container, you must set the drain select switch to OFF or the water can
overflow from the drainage container
Although the unit has been tested at the factory, due to long-term transit and storage, the first
batch of cubes must be discarded.
Do not use solvent-based cleaning agents of abrasives on the interior. These cleaners may
damage or discolor the interior.
Do not use this apparatus for other than its intended purpose.
4
HELP US HELP YOU...
Read this guide carefully.
Write down the model and serial numbers.
It is intended to help you operate and maintain
your new Beer Dispenser properly.
You'll find them on a plate located on the rear
wall of the Beer Dispenser.
Keep it handy to answer your questions.
If you don't understand something or you need
more assistance, please call:
Please write these numbers here:
____________________________________
Date of Purchase
Avanti Customer Service
800-220-5570
____________________________________
Model Number
Keep proof of original purchase date (such as
your sales slip) with this guide to establish the
warranty period.
____________________________________
Serial Number
CAUTION:
Use these numbers in any correspondence or
service calls concerning your Beer Dispenser.
THIS BEER DISPENSER IS NOT
DESIGNED FOR THE STORAGE
OF MEDICINE OR OTHER
MEDICAL PRODUCTS.
If you received a damaged Beer Dispenser,
immediately contact the dealer (or builder) that
sold you the Beer Dispenser.
Save time and money. Before you call for
service, check the Troubleshooting Guide. It
lists causes of minor operating problems that
you can correct yourself.
IF YOU NEED SERVICE
We're proud of our service and want you to be
pleased. If for some reason you are not happy
with the service you receive, here are some
steps to follow for further assistance.
NEXT, if you are still not pleased, write all the
details, including your telephone number, and
send to:
Customer Service
Avanti Products
FIRST, contact the people who serviced your
Beer Dispenser. Explain why you are not
pleased. In most cases, this will solve the
problem.
10880 NW 30 Street
Miami, FL 33172 USA
5
PARTS AND FEATURES
1
2
3
4
5
6
Beer Tower
Safety Guard Rail
Drip Tray
7
8
9
10
11
12
Stainless Steel Door
CO2 Tank Holder
CO2 Tank
Keg Support Plate
Leveling Leg
Adjustable Temperature Control
Pressure Regulator
Evaporator
Standard Leg
6
PARTS / ACCESSORIES - DETAILED
Accessories
Qty
1
1
1. Keg Coupler
2. Back Flow Stopper
3. Rubber Washer
1
4. CO2 Rubber Directional Washer
1
5. Beer Tower Washer
6. Beer Tower Tap/Beer Hose Assembly
7. CO2 Regulator
1
1
1
8. High Pressure Washer
9. CO2 Tank Valve
1
1
10. Guard Rail
1
11. Drip Pan Top
1
12. Drip Pan
1
13. Rubber Foot
4
14. Keg Support Plate
15. Metal Washer
1
4
16. Caster with Brake
(Optional – Sold Separately)
17. Casters
2
2
(Optional – Sold Separately)
18. CO2 Tank Strap
19. Air hose Wing Nut Washer
20. Air Hose
21. Air Hose Connector Washer
22. Beer Tap Wrench
23. Regulator Wrench
24. Beer Tower Hole Cover
25. Extra Washers (3, 4, 8, 19, 21)
1
1
1
1
1
1
1
1
7
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock, or injury when using
your Beer Dispenser, follow these basic precautions:
WARNING
Read all instructions before using the unit.
DANGER or WARNING: Risk of child entrapment.
Child entrapment and suffocation are not problems of the past. Junked or abandoned
appliances are still dangerous . . . even if they will “just sit in the garage a few days”.
Before you throw away your old unit: Take off the door. Leave the shelves in place
so that children may not easily climb inside.
Never allow children to operate, play with, or crawl inside the unit.
Never clean unit parts with flammable fluids. The fumes can create a fire hazard or
explosion.
Do not store or use gasoline or any other flammable vapors and liquids in the vicinity of
this or any other unit. The fumes can create a fire hazard or explosion.
-Save these instructions-
INSTALLATION INSTRUCTIONS
Before Using Your Beer Dispenser
Remove the exterior and interior packing.
Check to be sure you have all of the following parts:
1
Instruction Manual
1
Beer Keg Coupler (Sankey Tap)
1
1
1
2
1
Safety Guard Rail
10 Keg Coupler Sealing Rings (Plastic Bag)
Drip Tray Assembly (Two pieces)
Beer Keg Support Plate (Plastic)
Refrigerator Shelves (Wire)
Beer Tower Assembly
1
1
1
1
Metal Wrench for Faucet installation
Steel Clamp for Hose (RED) installation
Beer Hose (Clear) with Sankey connector
CO2 Tank and Accessories
1 – Faucet
1 – CO2 Cylinder / Tank (Empty)
1 – CO2 Cylinder / Tank Cushion
1 – CO2 Regulator
1 – CO2 Air Hose (Red) with connector
1 – CO2 Cylinder / Tank – Holder / Fastener
1 – Pull Handle (Black)
1 – Tower Top Cover (Plastic)
1 – Mylar Washer
2 – Faucet Sealing Rings (Plastic Bag)
Before connecting the Beer Dispenser to the power source, let it stand upright for
approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system
from handling during transportation.
Clean the interior surface with lukewarm water using a soft cloth.
Installation of Your Beer Dispenser
This appliance is designed to be free standing indoor use only, and should not be recessed or
built-in. If used outdoors, the unit must be protected from exposure to all types of harsh
weather conditions. High temperatures will affect the units cooling efficiency.
Place your Beer Dispenser on a floor that is strong enough to support the Beer Dispenser
when it is fully loaded.
Allow 5 inches of space between the back and sides of the Beer Dispenser,
which allows the proper air circulation to cool the compressor and condenser.
Locate the Beer Dispenser away from direct sunlight and sources of heat (stove, heater,
radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase
electrical consumption. Extreme cold ambient temperatures may also cause the Beer
Dispenser not to perform properly.
Avoid locating the Beer Dispenser in moist areas.
Plug the Beer Dispenser into an exclusive, properly installed-grounded wall outlet. Do not
under any circumstances cut or remove the third (ground) prong from the power cord. Any
8
questions concerning power and or grounding should be directed toward a certified electrician
or an authorized Avanti Products service center.
After plugging the appliance into a wall outlet, allow the unit to cool down for 2-3 hours before
placing any contents in the Beer Dispenser compartment.
ELECTRICAL CONNECTION
Warning
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is
damaged, have it replaced by an authorized Avanti Products service center.
This appliance should be properly grounded for your safety. The power cord of this appliance is
equipped with a three-prong plug which mates with standard three prong wall outlets to minimize the
possibility of electrical shock.
Do not under any circumstances cut or remove the third ground prong from the power cord supplied.
For personal safety, this appliance must be properly grounded.
This appliance requires a standard 115/120 Volt AC ~/60Hz electrical ground outlet with three-prong.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly
grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation
to have it replaced with a properly grounded 3-prong wall outlet.
The cord should be secured behind the appliance and not left exposed or dangling to
prevent accidental injury.
The appliance should always be plugged into its own individual electrical outlet which has a voltage
rating that matches the rating label on the appliance. This provides the best performance and also
prevent overloading house wiring circuits that could cause a fire hazard from overheated. Never
unplug the appliance by pulling the power cord. Always grip the plug firmly and pull straight out from
the receptacle. Repair or replace immediately all power cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
When moving the appliance, be careful not to damage the power cord.
EXTENSION CORD
Because of potential safety hazards under certain conditions, it is strongly recommended that you do
not use an extension cord with this appliance. However, if you must use an extension cord it is
absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord
having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at
least 10 amperes.
SURGE PROTECTOR
Most electrical appliances use a series of electric control boards to operate. These boards are very
susceptible to power surges and could be damaged or destroyed.
If the appliance is going to be used in an area or if your city / country is prone to power surges /
outages; it is suggested that you use a power surge protector for all electrical devices / appliances
you use. The surge protector that you select must have a surge block high enough to protect the
appliance it is connected to. If you have any questions regarding the type and size of surge protector
needed contact a licensed electrician in your area.
Damages due to power surges are not considered a manufacturer covered defect and will void your
product warranty.
9
Reversing the Door Swing of Your Appliance
This appliance has the capability of the door opening from either the left or right side. The unit is
delivered to you with the door opening from the left side. Should you desire to reverse the opening
direction, please call service for reversal instructions.
INSTALLING AND ASSEMBLING YOUR APPLIANCE
Casters with Brake (OPTIONAL ACCESSORIES) Installation
THESE CASTERS ARE NOT INCLUDED WITH YOUR UNIT.
Casters can be ordered from the Avanti Parts and Service Department at 1-800-220-5570 or by
using the Accessory Order Form included with this manual.
Install the four casters with lock provided into the unit’s bottom (four screw holes pre-supplied).
Figure (I) before installation. Figure (II) is the final version.
Figure (I): Before Installation
Figure (II): After Installation
WARNING
CO2 GAS CAN BE DANGEROUS
WARNING: CO2 cylinders contain high-pressure compressed gas which can be hazardous if not
handled properly. Make sure you READ and UNDERSTAND the following procedures for CO2
cylinders BEFORE INSTALLATION.
1. ALWAYS connect the CO2 cylinder to a regulator. Failure to do so could result in explosion
with possible death or injury when the cylinder valve is opened.
2. NEVER connect the CO2 cylinder directly to the product container.
3. ALWAYS follow correct procedures when cylinders are changed.
4. ALWAYS secure the cylinder in an upright position.
5. NEVER drop or throw a CO2 cylinder.
6. ALWAYS keep a CO2 cylinder away from heat. Store extra cylinders in a cool place
(preferably 70°F). Securely fasten with a chain in an upright position when storing.
7. ALWAYS ventilate and leave the area immediately if CO2 leakage has occurred.
8. ALWAYS check the D.O.T. test date on the cylinder neck before installation. If over five (5)
years, do not use, return cylinder to gas supplier.
9. NEVER connect a product container unless there are two (2) safety’s in the pressure system:
a. One at or on the CO2 regulator
b. One at or on the product coupler or in the pressure gas line.
10
Beer Keg Installation Sketch
Installation of CO2 Regulator
Attach the CO2 regulator to the cylinder by turning the regulator nut
onto cylinder valve, making sure washer is securely inserted into
connecting nut. Tighten snug using an adjustable wrench (not
supplied) and assure there are no leaks. (See Figure 1)
Figure 1
Installation Of CO2 Air Line Hose To Regulator
Attach the open end of the red hose to the hose barb connection on
the regulator. (See Figure 2)
Secure hose by using one clamp provided.
Use pliers/screwdriver to tighten clamp and assure no leaks.
Figure 2
11
Installation Of CO2 Tank Fasterner (see illustriation below)
Before install he CO2 Tank to it’s position, make sure to attached the Regulator and the CO2 red
hose first, securely tightened. The CO2 tank cushion should also be sticked to the bottom of the
tank.
First buckle the CO2 tank fasterner to one end of the inner lock piece at the right inner side.
Then put the CO2 tank in its position for safety lock.
Pull tight the fasterner and buckle the other end into the lock piece.
Check and make sure the buckle are tight and secure.
Installation of the Keg Coupler
Insert the keg coupler provided into the locking neck of the beer keg
and turn it clockwise to lock into position, making sure the keg coupler
is in the closed position. (See Figure 3)
Figure 3
Installation Of The Beer Tower
Remove the top plug by twisting and pulling out, saving it for later use if you decide to convert unit
to an all refrigerator unit.
For tight connection, you may need the Mylar washer provided, put it on the plastic socket which
accomodate the beer tower.
Unravel the beer line (clear hose) from the tower and insert the beer line and wing nut through the
uncovered hole on top.
Lock the beer tower assembly to the top and make sure to position the beer faucet so it is aligned
with the cabinet front (6 o’clock position). You accomplish this by aligning the bottom of the beer
tower to the 3 grooves on the top cabinet and tighten by hand clockwise to properly lock.
Installation Of The Keg Coupler
Insert the keg coupler provided into the locking neck of the beer keg and turn it clockwise to lock
into position, making sure the keg coupler is in the closed position. (See Figure 7)
Installation Of The CO2 Air Line Hose
Attach the end of the air line(red) hose provided to the hose connection on the keg coupler.
Secure hose by using the connector and make sure there are no leaks.
12
Connecting the beer tower to coupler
Make sure the washer is properly inserted into the wing nut.
Place wing nut into the top of the coupler turning until tight.
How To Tap A Keg Of Beer
Make sure the beer tower faucet is in the closed position.
Pull tapping handle out and press downward until it locks into position. (See Figure 8) The keg is
now tapped.
Opening The CO2 Cylinder Main Valve
Before doing that, make sure the secondary shut-off valve is closed, as shown in figure 9. To
open the main CO2 cylinder valve, slowly turn the main valve counter-clockwise until fully open.
Notice the needle on the gauge start to climb.
Adjusting The CO2 Regulator
The gauge monitors low internal keg pressure and should be adjusted to read between 10-12 psi.
(See Figure 10)
In order to do that:
1. Release adjustment lock nut marked 2.
2. Using a flat screwdriver, turn regulator screw marked 3. If increased low pressure is sought,
rotate screw clockwise. By rotating it counter clockwise, low pressure will be decreased when
the required operating pressure is attained, retighten lock nut 2.
Open secondary shut off valve to let CO2 flow into the keg.
Installation of Protective Plate
This plate should always be installed when the keg is in place to protect against unnecessary
damage to the floor of the cabinet liner.
Installation of the Beer Keg
Position the beer keg directly in front of the open door. Using keg handles only, carefully lift the
beer keg. (See Figure 3)
To place the beer keg inside the cabinet, brace your knees behind the beer keg. Lift the front of
the keg just enough so the front edge of the keg is resting on the front edge of the Beer Dispenser
bottom cabinet. (See Figure 4)
Grasp the keg handles and slide it all the way into the cabinet.
Figure 3
Figure 4
13
Spanner Faucet Wrench
Spanner faucet wrench provided for either removing or tightening
connection
Plastic Faucet Lever
Attach the black plastic lever (pull handle) provided on the top of the
faucet by tighten it by hand clockwise until the end, holding in the
process the silver snug underneath so it does not move.
If there is still a small drip from the faucet, you may have tightened the
plastic lever too much and may need to unscrew silver snug counter-
clockwise (as shown) one turn. That should correct the problem if
exists.
Dispensing Beer:
Keep beer keg refrigerated at all times.
Never allow beer lines to dry out.
Use clean beer glassware before pouring.
Hold glass at a 45° angle when 2/3 full, start to straighten glass and tap it off.
Always make sure the faucet handle is pushed all the way back.
Note: Keg sizes that can be used in your beer dispenser
1/2 barrel
1/4 barrel
1/6 barrel
1/8 barrel
59 Liters
30 Liters
20 Liters
15 Liters
15.5 gals
7.8 gals.
5.2 gals.
4.0 gals.
1984 oz.
992 oz.
661 oz.
496 oz.
164/12-oz. Glass
82/12-oz. Glass
55/ 12-oz. Glass
41/ 12-oz. Glass
Note: Our Beer dispenser accepts almost all, Brand Name ½ kegs. However Coors’ kegs do not fit in
our unit.
Converting Your Beer Dispenser To An “All Refrigerator”.
1. Turn off the control knob to the “OFF” position.
2. Close the main valve on the CO2 cylinder.
3. Close the secondary shut-off valve on the regulator pipe.
4. Close the connection between the beer keg and the keg coupler.
5. Drain any remaining beer from the lines.
6. Disconnect the beer line and CO2 air line from the keg coupler
7. Remove the beer keg .
8. Remove the keg coupler.
9. Disconnect the air line from the CO2 cylinder.
10. Remove the CO2 air line from cabinet plug
11. Remove the beer tower. Also pull the beer line thru the top of the cabinet
12. Replace the top cabinet plug
13. Put the wire shelves provided and install them on the side supports.
14. Adjust temperature as desired.
NOTE: Our Beer dispenser accepts almost all Brand Name ½ kegs. However Coors’ kegs do not fit in
our unit.
14
OPERATING YOUR BEER DISPENSER
Setting The Temperature
To start, turn the temperature control knob to the maximum setting (6) to
achieve coldest position quickly. Allow the unit to run for 3 hours.
Temperature range of the thermostat goes from 36°F to 45°F (2ºC to 7ºC).
Optimum temperature for serving draught beer is between 36°F – 38°F (2ºC
– 3ºC) and that is a key factor to consider in storing and dispensing draught
beer.
To turn off the Beer Dispenser, turn the control knob to the “OFF” position.
NOTE: Keep an accurate thermometer handy and adjust temperature control setting as necessary or
according to your needs.
Automatic Defrosting
There is no need to defrost the Beer Dispenser. Defrost water collects and passes through the drain
outlet in the rear wall into a tray located above the compressor, where it evaporates.
NOTE:
.
IF THE UNIT IS UNPLUGGED, POWER LOST, OR TURNED OFF, YOU MUST WAIT 3 TO 5
MINUTES BEFORE RESTARTING THE UNIT. IF YOU ATTEMPT TO RESTART BEFORE THIS
TIME DELAY, THE BEER DISPENSER WILL NOT START.
.
TURNING THE TEMPERATURE CONTROL TO “OFF” POSITION STOPS THE COOLING
CYCLE BUT DOES NOT SHUT OFF THE POWER TO THE UNIT.
CARE AND MAINTENANCE
Cleaning Your Beer Dispenser
Turn the temperature control to "OFF", unplug the Beer Dispenser, and remove the contents.
Wash the inside surfaces with a warm water and baking soda solution. The solution should be
about 2 tablespoons of baking soda to a quart of water.
Wash the shelves and metal plate with a mild detergent solution.
Wring excess water out of the sponge or cloth when cleaning area of the controls, or any
electrical parts.
Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with
a clean soft cloth.
Vacation Time
Short vacations: Leave the Beer Dispenser operating during vacations of less than three weeks.
Long vacations: If the appliance will not be used for several months, remove all contents and
unplug the power cord. Clean and dry the interior thoroughly. To prevent odor and mold growth,
leave the door open slightly: blocking it open if necessary.
Moving Your Beer Dispenser
Remove all the contents.
Securely tape down all loose items inside your Beer Dispenser.
Tape the door shut.
Be sure the Beer Dispenser stays secure in the upright position during transportation. Also
protect outside of Beer Dispenser with a blanket, or similar item.
15
DRAUGHT BEER TROUBLE GUIDE
CLOUDY BEER
When beer in glass appears hazy, and not clear.
Causes
Corrections
1
Over chilling beverage
cooler and/or beverage
lines.
Excessive low temperatures may cause hazy, cloudy beer,
particularly when beer lies in cold coil for long periods of time.
Make certain that lines are thoroughly cleaned, and then raise
temperature slightly.
2
3
Cracking, or when
partially opening beer
faucet.
Contaminated air
source. If possible
change to CO2 gas as a
pressure source.
Defective Thomas or
tongue vents.
Open faucet quickly and completely.
Replace worn washers and parts in faucet when necessary to
permit full opening of faucet.
See flat beer, correction #7
Always draw fresh air from an outside source to compressor.
Attach hair felt filter to the outside intake, in addition to filter in
line.
Bacteria growth may result from beer backing up through
defective vents in air line, air pressure will then carry this into
beer barrel.
Check and replace defective vents frequently, and thoroughly
clean air line.
See wild beer corrections #2, #5, #6, and #7, and flat beer
corrections #5, #7, and #8.
When unrefrigerated products, such as meats vegetables, fish,
or fruits, are placed on barrel of cold beer, the beer becomes
warm long before these products chill down to the cold
temperature. This change in temperature will cause Cloudy
Beer.
4
5
General conditions
causing cloudy beer.
Unrefrigerated food
placed on barrel on cold
beer.
LOOSE FOAM
Causes
Corrections
1
Large soap-like bubbles
(sometimes called fish
eyes). Foam settles
quickly.
This is generally a Flat Beer condition: the Causes and
corrections for Flat Beer should be followed.
TAIL END BEER
Beer draws well at the beginning of the barrel. Towards the end of the barrel the beer is flat.
This is more likely to occur when beer turnover is slow.
Causes
Corrections
1
Where air is used as a
pressure source, air
replaced the CO2 in
beer causing flat beer.
Where beer is being
drawn rapidly this
problem is not so
evident.
Wherever possible CO2 Gas should be used as pressure
source.
In high pressure systems where CO2 gas cannot be sued a
banner air-gas Blender should be installed. This introduces a
small amount of CO2 back into the beer, thus maintaining
normal CO2 content in beer.
16
FLAT BEER
Foamy head disappears quickly: beer lacks usual zestful brewery fresh flavor.
Causes
Corrections
1
Greasy glass
Do not wash beer glasses together with glasses that have
contained milk or any other fatty substance. Lipstick is a fatty
substance.. Make sure it is removed from glass.
Excess amount of germicides build up and leave a fatty film on
glass, which may cause flat beer.
It is preferable to steam and sterilize glasses where health
laws permit.
Wash glasses thoroughly with a good detergent.
Do not use soap.
Do not dry-wipe glasses. Permit glasses to air-dry by placing
them on wire or corrugated metal.
Rinse in fresh cold water just before serving beer. It is best to
serve beer in a wet glass.
2
Improper drawing of
beer into glass.
Open faucet quickly and completely.
Check and find the correct distance to hold glass from faucet
when drawing. Proper foam should be a tight creamy head,
and the collar on the average glass should be ¾” to 1” high.
Beer drawn without head has appearance of being flat.
Increase pressure if beer runs too slowly. Correct flow is to fill
Check all washers frequently, particularly the air vents. A
clogged vent will obstruct the flow of air or Co2.
Check source of pressure. Check power source when air
compressor is used. Air compressor should never be
connected to light switch. Make certain to have a separate
electric plug outlet for the compressor.
3
4
Not enough pressure.
Defective Thomas and
Tongue Vents.
Pressure is shut off.
Check CO2 tank, if empty, replace (See inside cover for proper
procedure).
When barrel is tapped, and proper pressure applied, pressure
must always remain on until barrel is empty.
If beer is started without first applying pressure beer will be
wild at the start, and flat towards the end.
With an accurate thermometer, check temperature in pre-
cooler or box.
Temperature at the faucet should always be colder by at least
two degrees than at the precooler or box.
A regular seat, or the regulator diaphragm, may require
replacing.
Also, check the same as you would for Corrections 3 & 4.
Filter all air after it leaves compressor.
Oil fume from compressor, of kitchen grease fumes, pumped
into beer, will cause Flat Beer.
If possible CO2 gas should be used as a pressure source.
With the use of an air compressor, it is imperative to have a
moisture trap installed in the Pre-cooler, and drained daily.
This is in addition to an activated charcoal filter, necessary to
purify the air just before it enters the barrel.
With tank type compressors, drain the tank weekly.
Moisture traps should be drained daily.
An air fan, or exhaust blower drawing air, or blowing air, across
the bar where beer is drawn, may cause the dead of foam to
fall quickly. Fans or blowers should be located so that air
movement is not directly across from where beer is drawn.
5
Pre-color, or beer
system, too cold.
6
7
Sluggish pressure
regulators.
Contaminated air
source.
Oil or grease fumes.
8
9
Moisture in Air system.
Rapid movement of air.
17
OFF-TASTE BEER
Often bitter and bitey, sometimes completely odor, carrying an unpleasant taste.
Beer lines should be flushed after each barrel is empty. Maintain fresh, Clean, sanitary
conditions at bar. Smoke, kitchen odors, fly sprays, and disinfectants will harm the tast and
flavor of beer, making it unpalatable. These conditions, as described, may come from an air
source, or from actual contact with the glass at bar.
Causes
Corrections
1
Improper, or no
cleaning of coils, hose,
leads, and direct draw
system.
Coils should be thoroughly cleaned at least once a week.
Brush and clean faucet. (see Wild Beer, Correction #2)
Taps, rods, and tap-Seal fitting should all be scoured, using a
detergent, then rinsed clean.
Direct draw Systems must be cleaned the same as coil
systems: 4 feet of direct draw line accumulates as much per
foot as any other system.
2
3
4
Contaminated Air Line.
Defective Thomas or
Tongue Bents.
Air hoses, air lines and vents, should be examined, and if
contaminated, replaced.
Dirty air lines should be washed with a good cleaning
compound, normally used for cleaning coils, and then rinsed
clean.
Rubber hose will absorb and retain odors. An approved Vinyl
tubing is best for air since it does not absorb moisture, and is
not affected by oily substances.
A fresh, outdoor, air line is imperative when air is the source
of pressure.
Rubber hose will
absorb and retain
odors.
Unfiltered air, Air is
moisture ridden or oily.
Air must always be filtered.
See Flat Beer, Correction #8 for moisture ridden air.
SOUR BEER
May taste and smell extremely yeasty, or moldy.
Causes
Corrections
1
2
Contaminated Air Line.
See Cloudy Beer, Correction #3
See Off-Taste Beer, Correction #2
See Flat Beer, Correction #7
If at all possible, deliver beer barrels in closed body,
refrigerated truck. If open staked body truck is used, cover
barrels with a tarpaulin for protection against summer heat,
and circulating warm air.
Truck should never be loaded the night before morning
delivery, unless beer is refrigerated in truck.
Improper transportation
of barrels of beer, Beer
delivered on open truck,
during high summer
temperatures, may be
the cause for starting
secondary fermentation.
No refrigeration, and
improper rotation.
3
The rule is first barrel in, first tapped.
Refrigeration must be left on winter or summer.
Sour beer is generated as a result of secondary fermentation,
above 45 degrees. Retail outlets that do not have refrigeration
should ice up barrels, or at least cover barrels with tarpaulin or
burlap bags.
Best temperature for barrels is 38° to 40°.
18
WILD BEER
Beer, when drawn, is all foam, or too much foam, and not enough liquid beer.
Cause
Improper drawing beer
into glass.
Corrections
Open faucet quickly and completely.
Check and find the correct distance to hold glass from faucet
when drawing. Proper foam should be a tight, creamy head,
and the collar on the average glass should be ¾ “ to 1” high.
1
2
3
Yeast growth, or other
obstructions in faucet.
Worn faucet parts and
worn faucet washers.
Kinks, dents, or twists in
coils, or direct draw
lines: obstructions in
line, near, or behind
faucet.
Clean faucet spout with a good brush daily. Scour all internal
faucet parts at least once a week.
Replace worn washers as required. If faucet does not open
wide, worn parts or entire faucet must be replaced.
Check for, and replace kinked, dented, or twisted line from
barrel to faucet.
Examine for frayed coupling washer behind faucet that may
cause obstruction.
4
5
Sag, or trap in line.
Keep all metal beer lines straight from barrel to faucet; never
permit lines to sag, as this creates traps that may cause wild
beer.
Temperature at faucet must always be at least 2 degrees
colder than at barrel.
In sweet-water refrigerated, or ice-water system, faucet
shank must always be submerged.
In Cold Air System, the coldest air from the blower must first
be directed to the faucet, and then circulated back to pre-
cooler.
Beer too warm at
faucet;
Beer too warm in Coil
System.
Beer too warm in Air
Shaft System.
6
7
Hot spots in line.
Insulate all beer lines; a long beer run must be constantly
refrigerated. Insulation helps. But insulation is not
refrigeration.
Keep all beer lines away from hot water pipes, hot air ducts,
and steam lines. A cold steam pipe in the summer is a hot
steam pipe in the winter.
It is always summer indoors and in the basement, therefore,
maintain pre-cooler, and direct draw dispenser temperature
at 40° all year round. If direct draw temperature cannot be
lowered, increase applied pressure; however, balance the
system by changing to smaller diameter length of vinyl tubing
or install a foam control faucet.
Pre-Cooler, or Direct
Draw Dispenser, too
warm.
Never shut off refrigeration – day or night.
8
No cold storage space
for delivered beer; beer
becomes warm in
barrel.
Coil systems, and direct draw systems, must be properly
balanced in order to apply pressure required for warmest
temperature to which barrels of beer will be exposed. A
control beer faucet can be used in place of a restricted coil to
balance system.
9
Too much air pressure.
Check source of pressure. Adjust pressure to suit properly
balanced system. For correct beer flow, fill a 10 oz. Glass in 4
seconds at proper temperature.
Check and replace a creeping regulator and gauge.
Adjust pressure when using CO2 as low as possible,
however, remembering that the applied pressure must be
slightly higher than the internal pressure of the beer (no more
than 18 lbs. should be applied.)
10
Excess CO2.
The colder the beer and the higher the applied CO2 pressure,
the more rapid the absorption of CO2 by the beer. This over-
carbonates the beer, causing Wild Beer.
19
11
12
Not enough pressure.
No pressure.
Check for defective air vents. (see Flat Beer, Corrections #3
and 4.)
Always turn pressure on before drawing beer.
Old Beer.
Rotate stock. The oldest beer should be tapped first; if beer
has been allowed to stand in warm temperature beyond 45°F
for any excessive length of time, it may begin secondary
fermentation.
Store beer at 40° all year round.
NOTES:
20
PROBLEMS WITH YOUR BEER DISPENSER?
You can solve many common Beer Dispenser problems easily, saving you the cost of a possible
service call. Try the suggestions below to see if you can solve the problem before calling the servicer.
TROUBLESHOOTING GUIDE
PROBLEM
Beer Dispenser does not operate.
POSSIBLE CAUSE
Not plugged in.
The circuit breaker tripped or blown fuse.
The temperature control knob is set in “OFF”
position.
Turns on and off frequently.
The room temperature is hotter than normal.
The door is open too often.
The door is not closed completely.
The temperature control is not set correctly.
The door gasket does not seal properly.
The Beer Dispenser does not have the correct
clearances.
Vibrations.
Check to assure that the Beer Dispenser is
leveled.
The Beer Dispenser seems to make too much
noise.
The rattling noise may come from the flow of the
refrigerant, which is normal.
As each cycle ends, you may hear gurgling
sounds caused by the flow of refrigerant in your
Beer Dispenser.
Contraction and expansion of the inside walls
may cause popping and crackling noises.
The Beer Dispenser is not leveled.
The Beer Dispenser is not leveled.
The door will not close properly.
The door was reversed and not properly installed.
The gasket is dirty.
The shelves or metal plate or beer keg are out of
position.
SERVICE FOR YOUR BEER DISPENSER
We are proud of our customer service organization and the network of professional service
technicians that provide service on your Avanti Beer Dispenser. With the purchase of your Avanti
Beer Dispenser, you can have the confidence that if you ever need additional information or
assistance, the Avanti Products Customer Service team will be here for you. Just call us toll-free.
AVANTI PRODUCTS CUSTOMER SERVICES
Product Information
800-323-5029
Part Orders
Whatever your questions are about our products,
help is available.
You may order parts and accessories that will be
delivered directly to your home.
800-220-5570
You may order these items by personal check,
money order, Master Card, or Visa.
In-Home Repair Service
800-220-5570
An Avanti Products authorized service center will
provide expert repair service, scheduled at a time
that is convenient for you. Our trained servicers
know your Beer Dispenser inside and out.
21
YOUR Avanti Products WARRANTY
Staple your sales receipt here. Proof of
original purchase date is needed to obtain
service under warranty.
WHAT IS COVERED
LIMITED ONE-YEAR
WARRANTY
LIMITED SECOND THROUGH
For one year from the date of
purchase by the original owner, Avanti
Products will, at its option, repair or
replace any part of the Beer Dispenser
which proves to be defective in
material or workmanship under normal
use. During this period Avanti
Products will provide all parts and
labor necessary to correct such
defects free of charge, so long as the
Beer Dispenser has been installed
and operated in accordance with the
written instructions in this manual.
Avanti Products will provide you with a
FIFTH YEAR WARRANTY
For the second through the fifth year from date
of original purchase, Avanti Products will
provide a replacement compressor free of
charge due to a failure. You are responsible
for the service labor and freight charges. In
rental or commercial use, the limited
compressor warranty is one year and nine
months. Cost to move the Beer Dispenser to
the servicers’ shop and back to the user's
home, as may be required, are the user's
responsibility.
reasonably
similar
replacement
product that is either new or factory
refurbished. In rental or commercial
use, the warranty period is 90 days.
All Avanti Appliances of 3.5 cubic feet
capacity or less must be brought/sent
to the appliance service shop for
repair.
WHAT IS NOT COVERED
Content losses of food due to spoilage.
Incidental or consequential damages.
Parts and labor costs for the following will
not be considered as warranty:
Evaporator doors, door springs, and/or
frames.
Inner door panels, door shelves, door
rails, and/or door supports.
Chest unitlid liners.
Vegetable crispers.
Light bulbs and/or plastic housing.
Plastic cabinet liners.
Punctured evaporator that voids the
warranty on the complete sealed system.
Shipping and Handling costs associated
with the replacement of the unit.
Repairs performed by unauthorized
servicers.
Service calls that do not involve defects in
material or workmanship such as
customer education, door reversal, or
proper installation.
Surcharges included, but not limited to,
any after hour, weekend, or holiday
service calls, tolls, ferry trip charges, or
mileage expense for service calls to
remote areas, including the State of
Alaska.
Service calls that are related to external
problems, such as abuse, misuse,
inadequate electrical power, accidents,
fire, floods, or acts of God.
Replacement of house fuses or resetting
circuit breakers.
Failure of the product if it is used for other
than its intended purpose.
This warranty does not apply outside the
Continental U.S.A.
22
INSTRUCCIONES EN ESPAÑOL
Para reducir el riesgo de incendio,
descarga eléctrica, o daño cuando use su
electrodoméstico, siga las siguientes
precauciones.
PRECAUCIÓN
Lea todas las instrucciones antes de usar su electrodoméstico.
Peligro o Precaución: Existe el riesgo que los niños queden atrapados.
Antes de desechar su dispensador de cerveza usado: Retire la puerta. Deje las
repisas en su lugar para evitar que los niños queden atrapados dentro.
No permita que los niños jueguen o entren dentro del dispensador.
No limpie su dispensador. con líquidos inflamables. Los gases pueden
ocasionar fuego o una explosión.
No guarde ni use gasolina u otros líquidos inflamables cerca de éste o de
cualquier otro electrodoméstico. Los vapores pueden ocasionar fuego o
explosión.
- Guarde estas instrucciones -
INSTRUCCIONES PARA LA INSTALACION
Antes de Usar su Electrodoméstico
Retire la envoltura interna y externa
Verifique que tenga las siguientes partes:
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
o
Manual de instrucciones
Carril de la parte superior
Bandeja de goteo (2 piezas)
Soporte de cilindro
Regulador del CO2 (GAS CARBONICO) (en una caja)
Cilindro CO2 (GAS CARBONICO) vacío (en una caja)
Manguera de la línea de aire CO2 (GAS CARBONICO) roja
Conectores de la manguera CO2 (GAS CARBONICO) (2 piezas)
Acoplador del barril de cerveza (en una caja)
Dispensador de cerveza con grifo
Manija del dispensador (grifo de la torre de cerveza)
4 Tapas para la bandeja de goteo
Soporte para el barril de cerveza
Plato de soporte para la parte inferior del gabinete
Llave de metal
Tapas para el gabinete superior
Antes de que conecte su Dispensador de Cerveza a la corriente eléctrica,
manténgalo ubicado en una superficie plana y vertical por lo menos por 2 horas.
Esto reducirá la posibilidad de malfuncionamiento en el sistema de enfriamiento por
el manipuleo durante el transporte.
Limpie la superficie interior con agua tibia utilizando un trapo suave.
Instalación de su Dispensador de Cerveza
Su dispensador ha sido diseñado para uso independiente y dentro de su casa
solamente. Si usa su dispensador al aire libre por un período pequeño, esté seguro
que esté protegido contra exposición a los efectos del clima o el medio ambiente.
Ubique su Dispensador de Cerveza en un piso que sea lo suficientemente fuerte
para soportar el peso de la unidad cuando esté totalmente lleno.
Deje más o menos 5 pulgadas de espacio entre la pared, la parte posterior y los
23
lados del electrodoméstico, lo cual permitirá la circulación de aire apropiado para
enfriar el compresor.
Aleje su Dispensador de Cerveza de la luz solar y de fuentes directas de calor
(estufa, calentador, radiador, etc.). Los rayos solares directos pueden malograr la
capa acrílica, y las fuentes de calor pueden ocasionar un aumento en el consumo
eléctrico. Los ambientes extremadamente fríos pueden afectar la eficiencia del
enfriamiento de su dispensador.
Evite ubicar el dispensador en áreas húmedas.
Conecte el dispensador a un enchufe de pared exclusivo e instale el cable de tierra.
Bajo ninguna razón se debe retirar la tercera punta del enchufe. Cualquier consulta
con respecto a la energía y/o cable de tierra debe ser dirigida a un electricista
certificado o autorizado por el Servicio Técnico de Avanti Products.
Después de enchufar el dispensador, deje que la unidad se enfríe de 2 a 3 horas
antes de poner cualquier contenido en el compartimiento del dispensador.
Conexión eléctrica
ADVERTENCIA
El uso inapropiado del enchufe a tierra puede desencadenar un choque eléctrico. Si el
cordón del enchufe del electrodoméstico se encuentra dañado, debe ser reemplazado
por el Servicio Técnico de Avanti Products.
El cordón del enchufe está equipado con tres puntas que encajan perfectamente en un
enchufe de pared standard para reducir el riesgo de un choque eléctrico.
Bajo ninguna circunstancia corte o saque la tercera punta del enchufe que le
proveemos, ya que esta es para que vaya conectada a tierra.
No use una extensión.
La corriente de este electrodoméstico es de 115/120 voltios, tiene una salida eléctrica de
60 hz. y consta de un enchufe de tres puntas que va conectado al enchufe de pared.
El cordón del enchufe debe ser asegurado atrás del electrodoméstico y no dejarlo
expuesto para evitar accidentes.
Nunca desenchufe el Dispensador de Cerveza tirando del cordón de corriente eléctrica.
Siempre tome firmemente el mango del enchufe y hale hacia usted.
ADVERTENCIA
GAS CO2 (GAS CARBONICO) PUEDE SER PELIGROSO
ADVERTENCIA: Los cilindros de CO2 (GAS CARBONICO) contienen un gas comprimido
de alta presión que puede ser peligroso si no es manejado correctamente. Cerciórese de
leer y entender las siguientes instrucciones relacionadas a los cilindros de CO2 (GAS
CARBONICO) antes de su instalación.
1. SIEMPRE conecte el cilindro de CO2 (GAS CARBONICO) a un regulador. Una falla al
momento de abrir la válvula podría dar lugar a una explosión, existiendo peligro de
muerte o lesión.
2. NUNCA conecte el cilindro de CO2 (GAS CARBONICO) directamente al recipiente del
producto.
3. SIEMPRE siga correctamente los procedimientos cuando los cilindros sean cambiados.
4. SIEMPRE esté seguro de que los cilindros estén en posición vertical.
5. NUNCA arroje o deje caer el cilindro de CO2 (GAS CARBONICO).
6. SIEMPRE mantenga el cilindro de CO2 (GAS CARBONICO) alejado del calor.
Almacene los cilindros extras en un lugar fresco (de preferencia 70º F).
7. SIEMPRE deje ventilada el área en caso ocurriese una fuga de CO2 (GAS
CARBONICO).
8. SIEMPRE controle la fecha de vencimiento D.O.T. en la tapa del cilindro antes de su
24
instalación. Si pasan 5 años y usted no lo utilizó, devuélvalo al surtidor del gas.
9. NUNCA conecte un recipiente del producto a menos que haya 2 seguros en el sistema
de presión:
a. Uno en el regulador de CO2 (GAS CARBONICO).
b. Uno en el acoplador del producto o en la línea de presión del gas.
Instalación del Cilindro de CO2 (GAS CARBONICO)
Instale el cilindro completamente cargado en el soporte de metal.
Instalación del Regulador de CO2 (GAS CARBONICO)
Una el regulador de CO2 (GAS CARBONICO) al cilindro girando la tuerca del regulador
sobre la válvula del cilindro, cerciórese de colocar la tuerca. Apriete con una llave
ajustable y asegúrese de que no haya ningún escape de CO2 (GAS CARBONICO).
(Vea la figura 1).
Instalación de la Manguera de Aire de CO2 (GAS CARBONICO) al Regulador
Junte el extremo de la manguera de aire (roja) a la conexión de la manguera en el
regulador.
Asegure la manguera usando una de las dos presillas de ajuste proporcionadas. Utilice
los alicates para apretar la presilla de ajuste y asegúrese que no hayan fugas.
Instalación de la torre al acoplador
Asegúrese que la empacadura este bién colocada en la rosca tipo mariposa.
Coloque rosca tipo mariposa en el acoplador y ajústela firmemente.
Instalación de la Línea de Aire dentro del Compartimiento
Retire la tapa situada en la parte posterior (esquina superior de la mano izquierda).
Guárdela para después en caso de que decida convertir la unidad a refrigerador.
Inserte el extremo abierto de la línea de aire (roja) en el compartimiento a
través del agujero descubierto.
Instalación de la Torre
Retire la tapa girando y halando. Guárdela para después, en caso decida convertir su
unidad de dispensador a refrigerador.
Desenrede la manguera que traslada la cerveza desde la torre e insértela junto con la
tuerca tipo mariposa, a través de la apertura.
Asegure la torre ensamblada a la parte superior y verifique que la posición del grifo
surtidor de cerveza se encuentra alineado con el gabinete frontal. Logre esto alineando
las tres alas en la parte inferior de la torre de cerveza a los tres agujeros destapados en
la parte superior del gabinete y ajústelos con la mano de manera que queden
apropiadamente cerrados.
Instalación del barril de cerveza
Coloque el soporte del barril de cerveza frente a la puerta abierta. Utilizando las asas del
barril, levántelo cuidadosamente y sobre el soporte del barril de cerveza.
Para ubicar el barril de cerveza colóquelo dentro de la cabina, doble ligeramente sus
rodillas y levante el barril usando las asas posteriores del soporte, solo lo suficiente, de
manera que pueda colocar el frente del barril con el frente de la cabina.
Agarre el soporte del barril por las asas y deslícelo dentro de la cabina. (Vea figuras 3 y
4)
Instalación del adaptador del barril
Inserte el adaptador del barril que se provee dentro del cuello del barril de cerveza y
gírelo en sentido horario para asegurarlo en posición
25
Instalación de la manguera de aire CO2 (GAS CARBONICO)
o
Una el extremo de la manguera roja a la manguera de conexión en el barril acoplador,
conectando la llave dispensadora de cerveza al acoplador.
o
Asegure la manguera usando el broche de presión de plástico que se proveé, usando
alicates para ajustar con grampas. (Vea figura 5)
o
o
Cerciórese de que la arandela esté insertada correctamente en la tuerca de ala.
Coloque la tuerca de ala en la tapa del acoplador y dele la vuelta firmemente.
Como servir la cerveza desde la Torre
Cerciórese que el grifo de la torre de la cerveza esté en la posición “Cerrada”.
Hale y presione hacia abajo la manija surtidora del acoplador hasta que quede
asegurada.
El barril proporcionará la cerveza deseada por el usuario.
Como abrir la válvula principal del CO2 (GAS CARBONICO)
Antes de hacer esto, asegúrese que la válvula secundaria de corte esté cerrada,
(POSICION HORIZONTAL) como se muestra en la figura (Pagina 13). Para abrir la
válvula principal del cilindro de CO2 (GAS CARBONICO), gire lentamente la válvula
principal en dirección contrario al sentido horario.
Note que la aguja empieza a subir.
Como ajustar el regulador del CO2 (GAS CARBONICO)
Afloje la tuerca de fijación.
Al ajustar el regulador del CO2 (GAS CARBONICO), la aguja vigila la presión interna
baja del barril. Ajústelo para que lea entre 10-12 PSI.
Como ajustar: Con un destornillador plano, de vuelta al tornillo del regulador marcado
“vea fig 6”. Si se necesita aumentar la presión, rote el tornillo en sentido de las agujas
del reloj. El tornillo en dirección contraria a las manecillas del reloj, disminuirá la
presión. Cuando se logra la presión de funcionamiento requerida, vuelva a apretar la
tuerca de fijación “vea fig 8”.
Abra la válvula (posición vertical) secundaria para dejar el CO2 (GAS CARBONICO) fluir
en el barril.
Dispensando Cerveza
Mantenga el barril de cerveza refrigerado todo el tiempo
Nunca permita que las vías de cerveza queden secas
Use vasos bien limpios
Sostenga el vaso en un ángulo de 45°, cuando esté 2/3 lleno empiece a enderezar el
vaso y cierre el grifo
Siempre asegúrese que la manija del grifo esté cerrada.
La llave de cerradura para el grifo del Dispensador de Cerveza está disponible para que
el dispensador solamente pueda ser usado por personas mayores de edad.
Nota :
Capacidad y medidas de los barriles que pueden ser usados para surtir cerveza
59 Litros (1/2 barril)
20 Litros (1/6 barril)
30 Litros (1/4 barril)
15 Litros (1/8 barril)
26
Convierta su Dispensador de Cerveza en “Todo un Refrigerador”
1. Gire el control a la posición “OFF”.
2. Cierre la válvula principal en el cilindro de CO2 (GAS CARBONICO).
3. Cierre la válvula de desconexión secundaria en el tubo del regulador.
4. Cierre la conexión entre el barril de la cerveza y el acoplador del barril.
5. Drene cualquier tipo de residuo de cerveza en las vías.
6. Desconecte las vías de cerveza y las vías de aire CO2 (GAS CARBONICO) del barril de
cerveza.
7. Retire el barril de cerveza, el soporte y el platillo de metal inferior de la cabina.
8. Retire el adaptador del barril.
9. Desconecte la vía de aire del cilindro de CO2 (GAS CARBONICO).
10. Retire la vía de aire CO2 (GAS CARBONICO) de la tapa de la cabina.
11. Reemplace la tapa de la vía de aire posterior.
12. Retire la torre de cerveza. También tire de la línea de la cerveza a través del hueco de
la cabina superior.
13. Reemplace la tapa superior del gabinete.
14. Instale las parrillas opcionales en los soportes laterales.
15. Ajuste la temperatura a su gusto.
USANDO SU DISPENSADOR DE CERVEZA
Control de temperatura
Para empezar, gire el control de temperatura al nivel más alto (MAX)
para enfriamiento rápido. Deje que la unidad funcione por 3 horas
seguidas. La temperatura del termostato se puede ajustar desde 36
°F a 45 °F (2ºC to 7ºC).
La temperatura óptima para servir cerveza es entre 36° F y 38° F
(2ºC – 3ºC) y ese es un factor importante que debe considerar para
almacenar y surtir cerveza.
Para apagar su dispensador, gire el control a la posición “OFF”.
NOTA: Mantenga un termómetro adecuado a la mano y ajuste el control temperatura según
sus necesidades.
Descongelamiento Automático
No hay necesidad de descongelar el dispensador de la cerveza. Toda el agua
descongelada pasa por la salida de drenaje por la pared posterior, a una bandeja ubicada
sobre el compresor, donde se evaporará.
.
NOTA Si la unidad es desenchufada, pierde poder o es apagada, espere de 3 a 5
minutos antes de reiniciar la unidad. Si usted intenta reiniciar antes de este tiempo, es
muy posible que el dispensador no funcione.
27
CUIDADO Y MANTENIMIENTO
Instalación de la puerta del Dispensador de Cerveza
El Dispensador de Cerveza tiene la capacidad de poderse abrir no solo por la izquierda sino
también por el lado derecho. La unidad viene con una puerta que se abre por la izquierda.
Como Cambiar la Direccion de Apertura de la Puerta
En caso de que necesite cambiar el lado de apertura de la puerta, por favor consulte al
servicio posventa de su localidad o al empleado que le vendió la unidad.
Limpieza de su Dispensador de Cerveza
Girar el control de temperatura a OFF, desenchufe el Dispensador de Cerveza y vacíe el
contenido.
Lave el interior con agua tibia y un trapo suave remojado en una solución de bicarbonato
de sodio. La solución consiste en 2 cucharadas de bicarbonato de sodio y un litro de
agua.
Lave las repisas y cabina con un detergente suave.
Exprima el exceso de agua de la esponja o trapo cuando limpie áreas como controles o
partes eléctricas.
Las partes externas de su dispensador. deben ser limpiadas con un detergente suave y
agua tibia. Enjuague bien y seque el interior y exterior con un trapo suave.
Si usted sale de vacaciones
Vacaciones cortas: Deje su Dispensador de Cerveza funcionando si sus vacaciones
serán de menos de 3 semanas.
Vacaciones largas: Retire el contenido interior de su dispensador. Desconecte su
dispensador y límpielo. Deje la puerta de su congelador ligeramente abierta para evitar
la formación de mal olor o moho. En el caso de ser un largo tiempo de almacenamiento,
selle la puerta con cinta adhesiva para que no se abra o retírela.
Para mover su dispensador
Retire todo el contenido del dispensador.
Asegúrese de colocar cinta adhesiva a todo lo que se puede caer dentro de su
dispensador.
Retire las patas para prevenir accidentes.
Selle las puertas con cinta adhesiva.
Asegúrese que el dispensador se mantenga parado durante el traslado. También
proteja el exterior del Dispensador de Cerveza con una manta o algo similar.
28
CERVEZA TURBIA
La bebida no se muestra cristalina
CAUSAS
CORRECCIONES
La temperatura del nivel de
enfriamiento de las bebidas está muy
baja
La nubosidad en la cerveza es causada por
excesiva baja temperatura, particularmente
cuando la cerveza permanece recostada en
el espiral por un periodo de tiempo largo.
Verifique que las líneas estén perfectamente
limpias, y suba ligeramente la temperatura.
Crujidos
o
cuando
se
abre
Abra el grifo rápido y completamente.
Reemplace los anillos gastados y partes del
grifo cuando sea necesario, ya que esto
permitirá que se pueda abrir el grifo
completamente.
parcialmente el grifo del dispensador
Condiciones generales que ocasiona
nubosidad en la cerveza.
Ver correcciones para cerveza rebelde.
CERVEZA ACIDA
La bebida tiene un olor y sabor a rancio o pasado
CAUSAS
CORRECCIONES
La línea de aire está contaminada
Transporte inapropiado de los barriles
de cerveza, cuando se transporta en
un camión no refrigerado durante la
temporada de verano en que las
temperaturas son muy altas, puede
causar que se inicie una fermentación
secundaria
Ver OFF-Taste Beer Corrección.
Si es posible, envíe todos los barriles de
cerveza completamente cerrados en un
camión refrigerado. Si se usa un camión
que no está completamente cerrado y no
cubre los barriles, cúbralos con tarpaulín o
bolsas de yute o fardo para protegerlos del
calor, clima y la circulación de aire caliente.
El camión nunca debe ser cargado la
noche anterior a la mañana en que se hará
el envío de barriles, a menos que la
cerveza esté refrigerada en el camión.
La regla es: conecte primero el barril con
fecha de vencimiento más próxima.
La refrigeración debe realizarse en invierno
o en verano.
Falta de refrigeración o rotación de
barriles inapropiada
La cerveza se acidifica como resultado de
la fermentación secundaria, por encima de
los 45 grados. Los comerciantes de
barriles de cerveza que no tienen
refrigeración deben mantener fresca la
parte superior de los barriles o al menos
cubrirlos con tarpaulín o bolsas de yute o
fardo.
La temperatura perfecta para los barriles
de cerveza es de 36° a 40° grados.
29
CERVEZA SIN CUERPO
La espuma desaparece rápidamente, la cerveza carece de su acostumbrado sabor
fresco
CAUSAS
CORRECCIONES
Vasos grasosos
No lavar los vasos cerveceros junto con
vasos que hayan contenido leche, o
cualquier tipo de sustancia grasosa. Las
pinturas de labios contienen una sustancia
grasosa, asegúrese de que se retire bien al
lavar los vasos.
El exceso de gérmenes deja una película
de grasa en los vasos, lo que ocasiona que
la cerveza pierda cuerpo inmediatamente.
Es preferible vaporizar y esterilizar los
vasos si esto es permitido.
Lave los vasos minuciosamente y con un
buen detergente.
No use jabón.
No seque los vasos con secador. Déjelos
secar al aire libre colocándolos en un
escurridor de rejillas de metal.
Enjuague con agua helada o fresca sólo
antes de servir la cerveza. Es mejor servir
la cerveza en un vaso mojado.
Chorro inapropiado del Dispensador
de Cerveza
Abra el grifo rápido y completamente.
Verifique y encuentre la distancia correcta
entre el grifo y el vaso en el momento que
sale la cerveza del grifo.
La espuma debe quedar arriba de la
cerveza y el collar promedio del vaso de
cerveza debe ser de ¾ de pulgada a 1
pulgada de alto.
Cerveza servida sin espuma da la
apariencia de no tener cuerpo.
Aumente la presión si la cerveza sale muy
lentamente.
El regulador de diafragma pueda que
requiera un cambio.
No hay suficiente presión
Reguladores de presión lentos
30
PERDIDA DE ESPUMA
CORRECCIONES
CAUSAS
La espuma muestra burbujas grandes
(como ojos de pescado) o se asienta
rápido
Esto es generalmente una cerveza sin
cuerpo: se deben de seguir las causas y
correcciones para cerveza sin cuerpo.
CERVEZA SIN SABOR
A menudo amargo a veces con olor o sabor desagradable
Las vías de la cerveza deben ser enjuagadas después de vaciar cada barril.
Mantenga las condiciones sanitarias del bar frescas y limpias. Humo de cigarrillo,
olor de cocina, vaporizadores aromáticos, y desinfectantes dañarán el sabor y el
gusto de la cerveza haciéndola desagradable. Las condiciones descritas pueden
venir del ambiente, o del contacto con los vasos del bar
CAUSAS
CORRECCIONES
Inapropiadas mangueras y sistemas
que dirigen el drenaje
Cepille y limpie el grifo (Vea cerveza
rebelde, Corrección).
Casquillos, varillas y barras deben ser
lavadas usando detergente y
enjuagándolas cuidadosamente.
El sistema de drenaje directo debe ser
limpiado igual que el sistema de enrollado:
4 pies del sistema de drenaje directo
acumula la misma cantidad por pie que
cualquier otro tipo de sistema.
Vía de aire contaminada
Mangueras de aire, vías de aire, deben ser
examinadas. Si están contaminadas,
reemplácelas.
Las vías de aire contaminadas deben ser
lavadas con un buen detergente, de los que
se usan para limpiar mangueras de espiral
y enjuagándolas cuidadosamente
Mangueras de goma absorben y retienen
olores. Puede usar tubo de vinilo regulado
y aprobado y son lo mejor para el aire ya
que no absorben humedad y no pueden ser
afectados por sustancias grasosas. Una
línea de aire fresca es importante cuando el
origen de la presión es el aire.
Mangueras de goma absorben y
retienen olores
31
CERVEZA REBELDE
Cuando la cerveza es pura espuma, o demasiada espuma, y no hay casi nada de
cerveza líquida
CAUSAS
CORRECCIONES
La cerveza es vertida
inapropiadamente dentro del vaso
Abra el grifo rápida y completamente.
Verifique y encuentre la distancia correcta
entre el grifo y el vaso en el momento que
sale la cerveza del grifo.
La espuma debe quedar arriba de la
cerveza y el collar promedio del vaso de
cerveza debe ser de ¾ de pulgada a 1
pulgada de alto.
Acumulación de levadura u otras
sustancias en el grifo
Limpie diariamente el orificio del grifo con
una escobilla. Refriegue el interior del grifo
con un buen cepillo una vez a la semana.
Reemplace los anillos sólo cuando sea
necesario. Si cuando abre la llave sale
poca cerveza, la llave debe ser cambiada.
Verifique las vías, desde el barril hasta la
llave del dispensador y remplácelas si
están dobladas o golpeadas.
Partes gastadas de la llave y anillos
de la llave desgastados
Mangueras torcidas o rajadas:
obstrucciones en línea, cerca o detrás
del grifo
Examinar que es lo que causa obstrucción.
Mantenga todas las vías de metal derechas
desde el barril hacia el grifo, jamás permita
que las vías se hundan y creen trampas
que podrían causar una cerveza rebelde.
Verifique la fuente de presión. Ajuste la
presión a la más adecuada. Para un
correcto flujo de cerveza, llene 10 oz. en un
vaso por 4 segundos a la temperatura
adecuada.
Vías hundidas y con trampas
Demasiada presión de aire
Verifique y reemplace el regulador.
Ajuste la presión usando CO2 (GAS
CARBONICO) al nivel más bajo posible, y
al mismo tiempo recuerde que la presión
aplicada debe ser ligeramente más alta que
la presión interna de la cerveza (no aplique
más de 18 lbs).
Exceso CO2 (GAS CARBONICO)
Mientras más fría esté la cerveza y más
alta sea la presión aplicada de CO2 (GAS
CARBONICO), la cerveza absorberá más
rápidamente el CO2. Esto carbonata la
cerveza en exceso, causando que la
cerveza se ponga rebelde.
No hay presión o esta no es suficiente
Verifique las salidas de aire defectuosas.
Vea corrección.
Siempre encienda la presión antes de
verter cerveza.
32
PROBLEMAS CON SU DISPENSADOR DE CERVEZA
Usted puede resolver muchos problemas comunes de su dispensador muy fácilmente,
ahorrando el gasto de una posible visita del servicio técnico.
Pruebe las siguientes sugerencias para verificar si usted puede resolver el problema antes
de llamar al servicio técnico.
GUIA PARA SOLUCIONAR PROBLEMAS
PROBLEMA
SOLUCION
Su Dispensador de Cerveza no funciona
No está conectado a la corriente eléctrica.
El interruptor saltó o se quemó un fusible.
El interruptor se enciende y se apaga La temperatura de la habitación es más
frecuentemente
caliente que lo normal.
Abre la puerta muy frecuentemente.
La puerta no está completamente cerrada.
Seleccione correctamente la temperatura.
El sellador de la puerta está sucio.
El Dispensador de Cerveza no tiene el
espacio suficiente.
El aparato vibra
Asegúrese que el electrodoméstico esté
ubicado en una superficie totalmente plana.
Ruido fuerte cuando comienza a trabajar el Los refrigeradores modernos tienen más
compresor
capacidad de almacenaje y temperatura más
uniforme. Estos requieren compresores más
eficientes. Ud. puede oír el compresor
cuando no hay ruido alrededor.
La puerta no cierra completamente
El refrigerador no está totalmente nivelado.
El sellador de la puerta está sucio.
La canasta de almacenaje está fuera de su
sitio obstaculizando el cierre de la puerta.
La temperatura de la habitación es más
caliente de lo normal.
Se enciende y se apaga frecuentemente
La puerta se abre demasiado seguido.
La puerta no está cerrada completamente.
El control de temperatura no está configurado
correctamente.
El sello de la puerta no es adecuado o los
soportes no están en posición adecuada.
El dispensador no cuenta con el espacio libre
adecuado.
33
NOTAS:
34
Registration Information
Thank you for purchasing this fine Avanti product. Please fill out this form and return it to the
following address within 100 days from the date of purchase and receive these important benefits:
Avanti Products, A Division of The Mackle Co., Inc.
P.O.Box 520604 – Miami, Florida 33152
Protect your product:
We will keep the model number and date of purchase of your new Avanti product on file to
help you refer to this information in the event of an insurance claim such as fire or theft.
Promote better products:
We value your input. Your responses will help us develop products designed to best meet
your future needs.
-------------------------------------------------------(detach here)--------------------------------------------------------------
Avanti Registration Card
Name
Model #
Serial #
Address
Date Purchased
Store / Dealer Name
City
State
Zip
E-mail Address
Occupation
Area Code
Phone Number
Did You Purchase An Additional Warranty
As your Primary Residence, Do You:
Extended
Own
Rent
None
Your Age:
Reason for Choosing This Avanti Product:
Please indicate the most important factors
That influenced your decision to purchase
this product:
under 18 18-25 26-30
31-35
36-50 over 50
Marital Status:
Married Single
Price
Product Features
Is This Product Used In The:
Avanti Reputation
Home
Business
Product Quality
Salesperson Recommendation
Other: ___________________
Friend / Relative Recommendation
Warranty
How Did You Learn About This Product:
Advertising
In-Store Demo
Personal Demo
Other: ___________________
Comments:
35
VER: 05-04-2010-01
PRINTED IN CHINA
36
|