MM530
5.3" LCD HEADREST MONITOR
IMPORTANT
An LCD panel and/or video monitor may be installed in a motor
vehicle and visible to the driver if the LCD panel or video monitor is
used for vehicle information, system control, rear or side observation
or navigation. If the LCD panel or video monitor is used for television
reception, video or DVD play, the LCD panel or video monitor must be
installed so that these features will only function then the vehicle is in
‘park’ or when the vehicle’s parking brake is applied.
An LCD panel or video monitor used for television reception, video or
DVD play that operates when the vehicle is in gear or when the parking
brake is not applied, must be installed to the rear of the driver’s seat
where it will not be visible, directly or indirectly, to the operator of the
motor vehicle.
A. Precaution:
1. Before installation, verify that it will not damage electrical wires, fuel
lines, brake lines, hoses, exhaust system components or any other
items that will impair the operation of the vehicle.
2. Ensure the cable has already been pulled through the supporting
pipe before installing the base into the headrest. Ensure there is no
foreign material trapped inside the enclosure before installing the
monitor into the base.
3. Tighten all screws/bolts/nuts securely for installation.
4. To avoid electrical hazards, do not disassemble the monitor.
5. Use only the supplied cables. Disconnect all cables from the
signal source before disconnecting it from the monitor.
6. Whencleaning, makesurethesystemisunplugged fromthepower
source.Donotuseliquidcleanersoraerosolcleaners.Useadamp
clothtocleantheunit.
3
B. Contents:
1. 1 x Main Unit MM530
2. 1 x AV Adapter Cable
3. 1 x Din-to-RCA Cable
4. 1 x Din Cable Clip
5. 1 x Owner’s Manual
6. 1 x Fan Bracket
C. Installation:
Front View
Top View
1.Installation will vary from vehicle to vehicle, as headrests in vehicles
are not standard.
2.This unit is intended for installation by professional installers.
3.The kit consists of the screen assembly, a clam shell housing and 1
key to remove the screen from the housing.
4
Headrest Mounting:
Mou ntin g
Tra y
Mon itor
1) Remove the headrest f
from the vehicle for easi-
est installation.
2) Lay headrest on a flat sur-
face.
3) Using a Permanent Marker,
mark headrest material
along the exterior of the
Mounting tray.
4) Remove the Trim Ring and
mark an “X” from corner to
corner as shown.
5
5) Using the utility knife, cut the
headrest material along the “X”
lines. Do not cut the material
along the other lines at this
time.
6) This will leave you with an “X” cut
as shown.
7) Pull the flaps up and cut the foam
beneath the material to the
proper depth. Cut all four sides
of the foam.
8) Using your fingers, tear the foam
out of the headrest leaving a
recess where the shell will be
inserted.
NOTE: At this point you will need to
install the harness up through the
area into the recess. It may be help-
ful to follow one of the posts and tie
wrap it to the post for restraint.
6
9) Lay the flaps of the headrest mate-
rial down into the recess and in-
sert the Mounting Tray into the re-
cess. Check for fit. If it does not fit
properly, you may need to remove
some more foam.
NOTE: The Mounting Tray will need to
be secured to the headrest, either
by using tie straps, screws, etc...
10) Guide the cable through the side
opening of the Mounting Tray and
plug it into the Monitor. Make sure
the connector locks into place.
Insert the Monitor into the Mount-
ing Tray and secure the cable
using tie wraps or screws
11) Turn the Monitor around and in-
sert it into the Mounting Tray hous-
ing. Snap into place.
12) Connect the Monitor‘s DIN Cable
to the external video source out-
put signal (from VCP/DVD, TV
Etc.)Test the system to verify
proper installation.
7
Fan Bracket Mounting*
The monitor can be mounted on a variety of surfaces using the
supplied fan bracket.
Select a location for the monitor and find a suitable surface to mount
the fan bracket. The mounting location* should be as firm, flat and
smooth as possible to ensure maximum adhesion. If the area is not
flat the bracket can be bent to conform to the shape of the surface.
Clean the area thoroughly and make sure that is dry before attempting
to mount the bracket. Remove the backing from the adhesive pad on
the bottom of the bracket and carefully place it in the desired mounting
location and press down firmly. Carefully align the mounting hole on
the bottom of the monitor with the screw on the top of the bracket.
Release the locking lever and turn the locking knob until it is tight.
Adjust the monitor angle and tighten the locking lever.
Screw
Locking Knob
Locking Lever
*Note: Please read the important notice on page three about monitor
location.
8
D. Controls/Indicators/Connectors:
Front View
5
6
7
8
9
1. AV Input Jack
2. Power Button
3. Source Button
4. Wide Button
5. Fan Bracket Mounting Hole
6. Picture Select Button
7. Volume Down Button
8. Volume Up Button
9. Headphone Jack
9
Rear View
9. DIN Jack
10. Video (Yellow)
11. Audio Left (White)
12. Audio Right (Red)
13. Red +12 VDC
14. Black Ground
10
E. Operation:
1. Connect the external AV source output signal (from VCP, DVD, TV
etc.) to the AV jacks (Video-yellow, Right Audio-red, Left Audio-white).
2. Press power button (2) to turn the monitor on and off. The backlight-
ing for the buttons will illuminate.
3. Press the volume up (7) or down (6) button to adjust the volume level.
4. Press the picture button (5) to adjust the picture quality. The adjust-
ments will be shown on the On Screen Display in the following se
quence: Color, Brightness, Contrast, and TINT. While in the picture
select mode (video adjustment), press the volume up button (7)
to increase the selected adjustment level or press the volume
down button (6) to decrease the level.
F. Specification:
1.LCD Panel:
ColorLiquidCrystalDisplay(LCD)
Monitor
2. Resolution:
480x234
3. VideoForma:t
NTSC
4.Power Source:
+12 VDC
600ma
5.Power Consumption:
6.Dimensions (W x H x D): (5.47”x 4.13”x0.87”)
139 x 105 x 22 mm
7.Weight:
10.4oz(295g)
11
12MONTHLIMITEDWARRANTY
Applies to Movies To Go Mobile Video Products
AUDIOVOX ELECTRONICS CORP. (the Company) warrants to the original retail
purchaser of this product that should this product or any part thereof, under
normal use and conditions, be proven defective in material or workmanship
within 12 months from the date of original purchase, such defect(s) will be repaired or replaced
with reconditioned product (at the Company's option) without charge for parts and repair labor. A
game controller, if supplied, is similarly waranteed for ninety (90) days.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered
with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation
prepaid, to the Company at the address shown below.
ThisWarrantydoesnotextendtotheeliminationofexternallygeneratedstaticornoise,tocorrection
of antenna problems, to costs incurred for installation, removal or reinstallation of the product, or
to damage to digital memory cards, discs, speakers, accessories, or vehicle electrical systems.
This Warranty does not apply to any product or part thereof which, in the opinion of the Company,
has suffered or been damaged through alteration, improper installation, mishandling, misuse,
neglect, accident, or by removal or defacement of the factory serial number/bar code label(s).
THEEXTENTOFTHECOMPANY'SLIABILITYUNDERTHISWARRANTYISLIMITEDTOTHE
REPAIRORREPLACEMENTPROVIDEDABOVEAND,INNOEVENT,SHALLTHECOMPANY'S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES,
INCLUDINGANYIMPLIEDWARRANTYOFMERCHANTABILITY,SHALLBELIMITEDTOTHE
DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY
WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY
MUST BE BROUGHT WITHIN A PERIOD OF 24 MONTHS FROM DATE OF ORIGINAL
PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL
ORINCIDENTALDAMAGESFORBREACHOFTHISORANYOTHERWARRANTY,EXPRESS
OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the
Company any liability other than expressed herein in connection with the sale of this product.
Somestatesdonotallowlimitationsonhowlonganimpliedwarrantylastsortheexclusionorlimitation
of incidental or consequential damage so the above limitations or exclusions may not apply to
you. This Warranty gives you specific legal rights and you may also have other rights which vary
from state to state.
U.S.A. : AUDIOVOX ELECTRONICS CORPORATION 150 MARCUS BLVD., HAUPPAUGE,
NEW YORK 11788 l 1-800-645-4994
CANADA : CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING
YOUR AREA
128-6924E
© 2005 Audiovox Electronics Corporation
128-7456A
12
|