Audiovox ACA450 User Manual

Wireless 4.5LCD Display System  
Model: ACA450  
Installation/User Manual  
Features:  
4.5" TFT Color LCD Display  
On Screen Display Function  
2.4 GHz Wireless Receiver  
Automatically Displays Image when Vehicle is in Reverse  
Warnings  
The product is intended to assist in safe driving and to allow the driver to  
have a broader rearview while the vehicle is in reverse. You, as the driver,  
are solely responsible for the safe operation of your vehicle and the safety  
of your passengers according to your local traffic regulations. Do not use  
any features of this system to the extent it distracts you from safe driving.  
Your first priority while driving should always be the safe operation of  
your vehicle. Audiovox Electronics Corporation cannot accept any  
responsibility whatsoever for accidents resulting from failure to observe  
these precautions or safety instructions.  
1. This product utilizes high voltage. Any unauthorized modifications  
or damage to the product may result in electrical shock. Handle all  
components with care. Inspect regularly for damage to  
components and cabling.  
2. You are responsible for ensuring that the installation of this  
product does not void or affect the vehicle manufacturer’s  
warranty. Audiovox Electronics Corporation or its subsidiaries are  
not liable in full or in part for improper installation resulting in  
loss or damage to your property, or for voiding all or part of the  
vehicle manufacturer’s warranty.  
3. Do not apply excessive force to any of the components contained  
within this kit. Excessive force used before, during or after  
installation that results in a damaged or non-functional part will  
void all warranties.  
4. Please follow the procedures in this installation manual. Improper  
installation or modification of this product will void all warranties.  
2
Product Description  
This Wireless Backup Camera/Monitor Package is designed to assist the  
driver by providing a clear and wide image of the area behind the vehicle  
whenever the vehicle is shifted into reverse. Never rely solely on this product  
to ensure the area is clear of children and/or obstructions. Use your monitor  
and look both ways. This product is not intended to replace existing safety  
procedures, but rather to add an additional safety tool for your vehicle.  
CAUTION: Do not back up your vehicle while watching the monitor screen.  
Always look in the direction the vehicle is traveling. Use the monitor as an aid  
to ensure there are no children or obstructions. The image on the monitor is  
not designed to show distance and may be misleading. The actual distance is  
less than appears in the monitor. The range of the image is limited. Be aware  
of blind spots.  
Packing list  
The model ACA-450 monitor package consists of the following items:  
1. LCD Wireless Reception Monitor 1 qty  
2. ACA200 Wireless Camera 1 qty  
3. Visor Clip 1 qty  
4. Mounting Bracket 1 qty  
5. 1.5m Power Supply Cable 1 qty  
6. 1.5m Cigarette Lighter Cable 1 qty  
7. Theft-proof Screws: 2 each course thread and machine thread  
8. Wire connectors:  
a) Tap connectors-1 qty  
b) Ring connector-1 qty  
3
Installation Instructions  
4-Bolt Amps Style Mount  
T-slot for Mounting  
Figure 2 (Mounting the Monitor)  
NOTE: Amps Style Mount is an industry standard 4-bolt pattern for assorted  
style mounts available at many retailers. Use caution when installing bolts, as  
bolts that are too long will damage the monitor.  
(1) Installing the Visor Clip (mounting bracket)  
a) Slide the Visor Clip all the way onto the T-slot on the back of the  
monitor, as shown in figure 2.  
b) Slide the Visor Clip over the sun visor.  
(2) Installing the Suction Cup Mount  
c) Slide the T-bolt on the base of the suction cup mount into the T-slot  
on the back of monitor display.  
d) Tighten the T-nut until snug with the back of the monitor.  
e) Place the suction cup on the windshield and adjust to a suitable angle  
for observing the image on the monitor. Be sure not to obstruct your  
view through the windshield.  
4
(3) Electrical Connections:  
The monitor can be powered two ways:  
1. Plug the cigarette lighter adapter into the vehicle’s cigarette  
lighter socket, and then insert the 2.5mm plug into the power  
supply jack on the monitor.  
2. Permanently wire the leads to the vehicle. Choose a source that  
only has power when the vehicle ignition is on.  
a. Red wire: ignition source +12 volt. Using the tap  
connectors supplied, perform the following steps:  
i. Place the un-stripped ignition source wire on the  
run channel  
ii. Place the un-stripped red power wire completely  
iii. Fold the tap connector back over the wires and  
make the connection by crimping the u-contact  
Tap/Run Connection  
down flush with the plastic insulator.  
iv. Close the top hinged cover until latched.  
b. Black wire: chassis/ground. Using the ground ring  
supplied, perform the following steps:  
i. Place stripped wire (1/4”) inside a connector  
ii. Crimp the connector using a crimping tool to  
secure the wire.  
c. Plug the power plug into the monitor power supply jack.  
Figure 3 (Electrical Connections)  
5
Controls and Indicators  
D
A
E
B
C
Figure 2 Back Side of Monitor  
Figure 2 illustrates the controls and indicators on the back side of the ACA450  
Monitor:  
A: Menu Key-shows on screen displays  
B: “+” Volume Adjustment Key  
C: “-” Volume Adjustment Key  
D: Four Position/Channel Receiver Frequency Switch  
NOTE: Position switch should be in the #1 position. Monitor can receive 4  
different frequencies, as noted in specifications, and can receive 4 separate  
camera signals (optional).  
E: Power Supply Jack  
6
Specifications  
General  
Power Supply  
Power Consumption  
Current Draw  
DC12V  
<6W  
<400 mA  
Operating Temperature Range  
0
to 50  
Display System  
Screen  
Brightness  
4.5” TFT Color LCD  
400 cd/  
Contrast Ratio  
Backlight Life  
Resolution  
150:1  
10000 hours  
960×234  
Video Format  
Display Format  
NTSC/PAL  
16 : 9  
Wireless Reception System  
Operating Frequency  
2.4GHz  
Selectable Channel Quantity  
4 Channel  
CH1: 2414 MHz,  
CH2: 2432 MHz,  
CH3: 2450 MHz,  
CH4: 2468 MHz  
Maintenance  
7
Though your monitor requires little care, you will still need to maintain its  
condition and performance by following the guidelines below.  
Keep your system away from excessive moisture, extreme heat or  
cold.  
Keep liquids away from the display.  
Occasionally clean the surface of the monitor with a soft cloth  
moistened with water or glass cleaner.  
Troubleshooting  
Symptoms  
Solutions  
1. Check the monitor wiring and  
connections  
2. Check that the channel switch is set  
to position 1  
The Monitor is not on after  
the vehicle is started and the  
vehicle is in reverse  
1. Check the rear view camera lens and  
Clean if needed  
2. Check the rear view camera wiring  
and connections  
No video signal appears while  
reversing the vehicle  
Video image is not sharp  
enough  
Clean the camera lens  
8
9
© 2007 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788  
10  

Ariens 927053 RM9028 User Manual
Attwood 4202 User Manual
Black Box Cable Box RMT3200A R2 User Manual
Bushnell Binoculars 118325 User Manual
Canon ZR45 MC User Manual
Casio Fraction Mate Scientific Calculator FX55BU TP User Manual
Casio fx 7400GII User Manual
Gitzo G1257LVL User Manual
Hasselblad H4D200MS User Manual
Hypertec 5701 User Manual