ABD40J
OWNER’S MANUAL
PLEASE READ THIS MANUAL
BEFORE OPERATING THIS UNIT
.
RETAIN FOR FUTURE REFERENCE.
TABLE OF CONTENTS
Introduction___________________________________________________
3
Features and Specifications______________________________________
Controls and Functions__________________________________________
Installation____________________________________________________
Warning and Disclaimer__________________________________________
Warranty______________________________________________________
4
5-6
7
8
9-10
INTRODUCTION
3
Dear Customer,
Congratulations on your purchase of the worlds finest brand of car audio products. Here at
Audiobahn Inc. we are devoted to making our musical reproduction the vert best, and we
are pleased you have chosen our product. Through years of engineering expertise, hand
craftsmanship, and critical testing procedures, we have created a wide range of products
that reproduce music with all the clarity and richness you deserve.
For maximum performance we recommend you have your Audiobahn product installed by
an Authorized Audiobahn Dealer, as we provide specialized training through our Audiobahn
Installer Training Programs. Please read your warranty, keep your receipt, and original
carton for possible future use.
To get a free brochure on Audiobahn products in the US call (714) 452-1476 or e-mail us at
WARNING
Continuous exposure to sound pressure levels over 100dB may cause permanent
hearing loss. High powered autosound systems may produce sound pressure levels
well over 135dB. Need we say more! Use common sense.
If after reading this manual you still have questions regarding your product, we recom-
mend that you see your nearest Audiobahn Dealer. A list of Authorized Audiobahn
Dealers can be found on our web page. If you need further assistance, feel free to call
us at (714) 452-1476 and ask for the Technical Department. Be sure to have the model
number, date of purchase, and invoice number available when you call.
The model number can be located on the outside of the carton. Record this in the space
provided below along with the date of purchase. It is a good idea to keep your receipt
with this as you will need it in the case of needing a warranty, repair service or ex-
change.
Date of Purchase: _____________________Model Number:___________________
Features and Specifications
4
Because of the variation in the process, we developed the ABD40J to help restore the low
frequencies lost during the process, but the acoustics of various environments are different.
Sweep control allows you to select a center frequency (the frequency most affected) be-
tween 27Hz - 63Hz
Width control then allows you to control the range of other filters centered on the frequency
Sweep.
Bass Processor: Contains circuitry that accurately recreates low frequency information
back into the signal.
L.E.D. Indicators: The three L.E.D. indicators flash when the low frequency equalization
circuit is activated and with increased Sound Pressure Level.
Remote Mount Control: This is a wired level control that allows the user to adjust the pro-
cessor from a remote location.
Specifications
Maximum Input Level________________________________
15V rms
Maximum Output Level_______________________________ 13.5V peak
Frequency Response________________________________
Total Harmonic Distortion_____________________________
10Hz-100kHz, + /-1dB
0.003%
Radio Signal to Noise________________________________ 130 dB
Noise rejection of balanced input_______________________ > 60 dB
Input Impedance____________________________________ 10Kohm
Output impedance___________________________________ 150 ohm
Power Source______________________________________ PWM
Power Extraction____________________________________ 150mA
Recommended Fuse_________________________________ 1 Amp
controls and functions
5
7
8
ABD4 0 J
WIDE
POWER
MAX
BASS CONTROL
MIN
MAX
5
6
SWEEP
R
-35Hz
-50Hz
-80Hz
MIN
MAX
DIGITAL BASS RECONSTRUCTION PROCESSOR
BALANCED
INPUT
OUTPUT
+12V GROUND
REMOTE
L
R
DASH REMOTE
L
R
PWR
SUB
LEVEL
MIN
MAX
1
3
2
4
1. Balanced Input: Low Input is used to balance the input circuit to help minimize noise.
They are designed to handle high voltage signals up to 15 volts.
2. Outputs: RCA connectors must be connected to the next component after the bass
processor, like a crossover, equalizer or amplifier. Remember the bass processor
must be connected before a crossover.
3. Remote Control.
4. Power connector
5. Controls: These two knobs control the functions of the Bass processor features.
SWEEP knob allows to choose the desired center frequency.
WIDE knob adjusts the frequency range of low impact processor.
6. The PFM subsonic filter switch: Bass Processor uses a PFM subsonic filter switch that
will helps the speaker control and manage the power amplifier. This switch comes with
three selections 35Hz/50Hz/80Hz frequency. In most programming systems is 35Hz, if
you want to further protect your speaker system, try a higher frequency. Often, higher
frequency sounds louder and clearer.
7. Maximize Bass Indicator: All three LED indicators flash when the maximization of the
lower circuit is activated.
8. The L.E.D. indicates when the unit is on.
CONTROLS AND FUNCTIONS
6
11
10V
7.5V
5V
2.5V
GROUND
ISO
9
200Ohm
UNBAL
Left
Right
10
BAL
9. Ground input: For most systems you can leave this jumper in the balanced position,
for some systems, the power source can find a ground through the RCA connectors.
In this case, change the jumpers to the UNBALANCED position.
10. Isolation of jumpers: Occasionally the alternator noise may appear on a system be-
cause of the power supply and amplifier different use. Switch the jumper.
NOTE: Make sure your system is off before you move these jumpers.
11. Controls Jumpers: Not all systems are designed equal. Some are designed strictly
for SPL (sound pressure level), low-maximizer circuit may increase or decrease the
voltage signal restoration circuit features. Depending on your system, you can choose
to change these jumpers to a setting higher or lower to maximize the output of and
protect your speakers.
Installation
7
ABD4 0 J
WIDE
POWER
MAX
BASS CONTROL
MIN
MAX
SWEEP
R
-35Hz
-50Hz
-80Hz
MIN
MAX
DIGITAL BASS RECONSTRUCTION PROCESSOR
BALANCED
INPUT
OUTPUT
+12V GROUND
REMOTE
L
R
DASH REMOTE
L
R
PWR
SUB
LEVEL
MIN
MAX
+
-
BATTERY
B + (12V): Connect the red wire to the car battery or other power source.
REMOTE: Connect the orange cable to the remote trigger cable (12V DC) of the car or
stereo equalizer.
GND: Connect the black wire to the chassis for grounding.
Warning And Disclaimer
8
TROUBLESHOOTING GUIDE
If the unit does not light up or the LED indicator light does nothing check the following:
1) Check to make sure the +B and GND are not reversed.
2) Check that all cables are connected properly and have adequate power (11-16 volts).
3) Check that the fuse is intact.
If you experience high or low volume audible distortion output:
4) Check that the input and output levels are set correctly.
5) Check the crossover, make sure it is correct. For systems of high “Q”, set 1 octave or
down.
If you experience noise of the machine:
6) Verify that the GND connection is secure, the conductor (cable) is not too thin and
unnecessarily long.
7) Check that the cable +B is not too thin and unnecessarily long.
8) Change the source for output.
Investigate the layout of your automobile thoroughly before drilling or cutting any holes. Take care
when you work near gas tanks, gas lines, hydraulic lines, and electrical wiring. Do not use the power ampli-
fier unmounted. Attach the system securely to the automobile to prevent damage, particularly in the event of
an accident. Do not mount the system so that the wire connections are unprotected or are subject to pinching
or damage from nearby objects.
The +12V DC power wire must be fused at the battery positive terminal connection. Before making or break-
ing power connections at the system power terminals, disconnect the +12V wire at the battery end. Con-
firm your radio/head unit and/or other equipment is turned off while connecting the input jacks and speaker
terminals. If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the
system. Using a fuse of a different type or rating may result in damage to this system which is not covered by
the warranty.
Disclaimer
Specifications are subject to change without notice.
For the most updated Specifications call Audiobahn,
your local Authorized Audiobahn Dealer,
or check the Audiobahn web site.
Warranty
9
Audiobahn Consumer
Product Warranty Policy
Audiobahn products are manufactured with the highest quality components and some of the most advanced
technology available. Because of this we recommend that you have your new products installed by an Au-
thorized Audiobahn Dealer. (A list of Authorized Audiobahn Dealers can be found on our web page).
Warranty Period: One year from the original date of purchase.
Warranty Coverage: This warranty covers manufacturer defects only. The warranty is applicable to the
original purchaser, and is non-transferable. You must provide a receipt from an Authorized Audiobahn
Dealer that shows the location of purchase, price paid, and date of purchase.
(Products purchased by consumers from an Authorized Audiobahn Dealer outside the United States are
covered only by the Distributor of that specific country and are not covered by Audiobahn).
NOTES:
Complete subwoofer enclosures (Audiobahn will replace defective subwoofers, plexiglass, or neon only. Do
not send the entire enclosure, unless the enclosure is defective itself. You must receive prior authorization
and an RA# before sending in any complete enclosure).
AUDIOBAHN DOES NOT WARRANTY ANY PRODUCTS NOT PURCHASED THROUGH AN AUTHO-
RIZED DEALER.
(A list of Authorized Audiobahn Dealers can be found on our web page).
AUDIOBAHN WARRANTIES DO NOT COVER THE FOLLOWING:
•
•
Any product not purchased from an Authorized Audiobahn Dealer (including Internet dealers)
Damage caused by abuse, misuse, accident, water / flood, or theft (including any cosmetic damage to
the body of the product)
•
•
•
•
•
•
•
•
Damage caused by improper installation
Any cost or expense related to removal or reinstallation
Any unauthorized services
Any product that has the serial number removed, altered, or defaced
Subsequent damage to any other components
Pinched, cut, or stripped wires / terminals
Any product that is new, and/or found to be in working condition
L.E.D. indicators on electronics (Audiobahn will only replace L.E.D.(s) found to be defective at the time
of purchase)
Warranty Continued
10
How to receive warranty service: Contact your local Authorized Audiobahn Dealer, or call Audiobahn at
(714) 452.1476 between the hours of 9:00AM and 5:00PM PST.
If you are having problems with your system, we recommend you check the product carefully and thoroughly
to confirm that the product truly has a manufacturer defect; as opposed to abuse, or other components in the
system caused the failure. This might include having an Authorized Audiobahn Dealer look at the product
to confirm the source of the problem. Any product found to have a manufacturer defect will be replaced with
a new piece of the same or similar model, or repaired at the discretion of Audiobahn. Any product found to
have no manufacturer defect will be returned to the sender at their cost.
You must acquire a Return Authorization Number (#) prior to returning ANY product to Audiobahn.
That Return Authorization Number (RA#) must be prominently and clearly marked on the outside of the ship-
ping carton, or product delivery will be refused (no exceptions will be made).
Please note: All shipping and handling (to and from) charges will be the sole responsibility of the consumer.
Please record and keep your Return Authorization Number (RA#) in the event that further communication is
required.
Return Authorization Number (RA#):
Date product was sent:
______________________________________
______________________________________
Contact Information
Audiobahn Headquarters
7050 Village Drive Bldg. G
Buena Park, CA 90621
Phone (714) 452.1476 Fax (888) 880.8469
Pacific Coast Time: 9am - 5pm Mon. - Fri.
7050 Village Drive, Bldg G
Buena Park, CA 90621
714-452-1476 oꢀce
888-880-8469 fax
PROUD SPONSOR OF
Follow us on Facebook and Twitter
|