VG248 series
LCD Monitor
User Guide
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
•
•
This device may not cause harmful interference, and
This device must accept any interference received including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with manufacturer’s
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The use of shielded cables for connection of the monitor to the graphics card is
required to assure compliance with FCC regulations. Changes or modifications
to this unit not expressly approved by the party responsible for compliance
could void the user’s authority to operate this equipment.
As an Energy Star® Partner, our company has determined that this
product meets the Energy Star® guidelines for energy efficiency.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise emissions
from digital apparatus set out in the Radio Interference Regulations of the
Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
This Class B digital apparatus meets all requirements of the Canadian Interference
- Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement
sur le matériel brouiller du Canada.
iv
Safety information
•
Before setting up the monitor, carefully read all the documentation that came
with the package.
•
•
To prevent fire or shock hazard, never expose the monitor to rain or moisture.
Never try to open the monitor cabinet. The dangerous high voltages inside the
monitor may result in serious physical injury.
•
•
If the power supply is broken, do not try to fix it by yourself. Contact a qualified
service technician or your retailer.
Before using the product, make sure all cables are correctly connected and the
power cables are not damaged. If you detect any damage, contact your dealer
immediately.
•
•
Slots and openings on the back or top of the cabinet are provided for
ventilation. Do not block these slots. Never place this product near or over a
radiator or heat source unless proper ventilation is provided.
The monitor should be operated only from the type of power source indicated
on the label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.
•
•
Use the appropriate power plug which complies with your local power standard.
Do not overload power strips and extention cords. Overloading can result in fire
or electric shock.
•
•
•
•
Avoid dust, humidity, and temperature extremes. Do not place the monitor in
any area where it may become wet. Place the monitor on a stable surface.
Unplug the unit during a lightning storm or if it will not be used for a long period
of time. This will protect the monitor from damage due to power surges.
Never push objects or spill liquid of any kind into the slots on the monitor
cabinet.
To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked between
100-240V AC.
•
If you encounter technical problems with the monitor, contact a qualified
service technician or your retailer.
This symbol of the crossed out wheeled bin indicates that the product (electrical,
electronic equipment, and mercury-containing button cell battery) should not
be placed in municipal waste. Please check local regulations for disposal of
electronic products.
v
Care & Cleaning
•
Before you lift or reposition your monitor, it is better to disconnect the cables
and power cord. Follow the correct lifting techniques when positioning the
monitor. When lifting or carrying the monitor, grasp the edges of the monitor.
Do not lift the display by the stand or the cord.
•
•
Cleaning. Turn your monitor off and unplug the power cord. Clean the monitor
surface with a lint-free, non-abrasive cloth. Stubborn stains may be removed
with a cloth dampened with mild cleaner.
Avoid using a cleaner containing alcohol or acetone. Use a cleaner intended
for use with the monitor. Never spray cleaner directly on the screen, as it may
drip inside the monitor and cause an electric shock.
The following symptoms are normal with the monitor:
•
The screen may flicker during the initial use due to the nature of the fluorescent
light. Turn off the Power Switch and turn it on again to make sure that the
flicker disappears.
•
•
You may find slightly uneven brightness on the screen depending on the
desktop pattern you use.
When the same image is displayed for hours, an afterimage of the previous
screen may remain after switching the image. The screen will recover slowly or
you can turn off the Power Switch for hours.
•
When the screen becomes black or flashes, or cannot work anymore, contact
your dealer or service center to fix it. Do not repair the screen by yourself!
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying to
complete a task.
CAUTION: Information to prevent damage to the components when trying
to complete a task.
IMPORTANT: Information that you MUST follow to complete a task.
NOTE: Tips and additional information to aid in completing a task.
vi
Where to find more information
Refer to the following sources for additional information and for product and
software updates.
1.
ASUS websites
The ASUS websites worldwide provide updated information on ASUS
2.
Optional documentation
Your product package may include optional documentation that may have
been added by your dealer. These documents are not part of the standard
package.
Takeback Services
ASUS recycling and takeback programs come from our commitment to the highest
standards for protecting our environment. We believe in providing solutions for
our customers to be able to responsibly recycle our products, batteries and other
components as well as the packaging materials.
information in different region.
vii
1.1
Welcome!
Thank you for purchasing the ASUS® LCD monitor!
The latest widescreen LCD monitor from ASUS provides a crisper, broader, and
brighter display, plus a host of features that enhance your viewing experience.
With these features, you can enjoy the convenience and delightful visual
experience that the monitor brings to you!
1.2
Package contents
Check your package for the following items:
LCD monitor
Monitor base
Quick start guide
Warranty card
Power cord
DVI (Dual-Link) cable
Audio cable
If any of the above items is damaged or missing, contact your retailer
immediately.
ASUS VG248QE LCD Monitor
1-1
1.3
Monitor introduction
1.3.1
Front view
1
2
3
4
5
6
1.
button:
•
Selects a desired preset mode.
•
Exits the OSD menu or goes back to the previous menu when the OSD
menu is active.
2.
•
Decreases values or moves your selection left/down.
•
GamePlus hotkey. Press
needed.
to select and MENU to confirm the function
3.
4.
MENU button:
•
Turns on the OSD menu. Enacts the selected OSD menu item.
•
•
Increases values or moves your selection right/up.
Brightness hotkey
5.
button:
•
Selects an available input source.
Press
(Input Select button) to display DVI/HDMI/DisplayPort signals after
you connect DVI/HDMI/DisplayPort cable with the monitor.
1-2
Chapter 1: Product introduction
6.
Power button/power indicator
•
•
Turns the monitor on/off.
The color definition of the power indicator is as the below table.
Status
Description
Blue
ON
Amber
OFF
Standby mode
OFF
1.3.2
Back view
4
6
Rear connectors
1.
2.
3.
AC-IN port. This port connects the power cord.
Displayport. This port is for connection for a DisplayPort compatible device.
DVI (Dual-Link) port. This 24-pin port is for PC (Personal Computer) DVI-
digital signal connection.
4.
HDMI port. This port is for connection with an HDMI compatible device.
Only DisplayPort and DVI ports support 3D feature given NVIDIA 3D
Vision Kit is available.
5.
6.
Audio-in port. This port connects PC audio source by the bundled audio
cable.
Earphone jack. This port is only available when an HDMI/DisplayPort cable
is connected.
ASUS VG248QE LCD Monitor
1-3
1.3.3
GamePlus Function
The GamePlus Function provides a toolkit and creates a better gaming environment for
users when playing different types of games. In addition, Aimpoint function is specially
designed for new gamers or beginners interested in First Person Shooter (FPS) games.
To active GamePlus:
1.
2.
3.
Press the GamePlus hotkey.
Press
to select between Aimpoint and Timer function.
Press MENU to confirm the function you choose, and
to go back, off, and exit.
GamePlus Main Menu
GamePlus — Aimpoint
GamePlus — Timer
GamePlus — Timer — Position
1-4
Chapter 1: Product introduction
2.1
Assembling the monitor arm/base
To assemble the monitor base:
1.
2.
3.
4.
Have the front of the monitor face down on a table.
Rotate the arm anti-clockwise 90 degrees. (Figure 1)
Fix the base to the arm by fastening the bundled screw. (Figure 2) (Figure 3)
Align the arrow mark on the base with the two screws to allow 90 degrees swivel
from either left or right.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
Figure 3
Figure 1
Figure 2
2.2
Adjusting the monitor
•
For optimal viewing, we recommend that you look at the full face of the
monitor, then adjust the monitor to the angle that is most comfortable for you.
•
•
Hold the stand to prevent the monitor from falling when you change its angle.
The recommended adjusting angle is +15˚ to -5˚ (for tilt)/+45˚ to -45˚ (for
swiveling/ +110 mm (for height adjustment)/90˚ (for portrait view).
It is normal that the monitor slightly shakes while you adjust the viewing angle.
ASUS VG248QE LCD Monitor
2-1
2.3
Detaching the arm (for VESA wall
mount)
The detachable arm of this monitor is specially designed for VESA wall mount.
To detach the arm:
1.
Have the front of the monitor face down on a table.
2.
Loosen the four screws on the back of the monitor and remove the arm/base.
We recommend that you cover the table surface with soft cloth to prevent
damage to the monitor.
2.4
Connecting the cables
Connect the cables as the following instructions:
Displayport
AC-IN
HDMI
Earphone jack
DVI
Audio-in
2-2
Chapter 2: Setup
•
•
To connect the power cord: connect one end of the power cord securely to
the monitor’s AC input, the other end to a power outlet.
To connect the DVI/HDMI/DisplayPort cable:
a. Plug one end of the DVI/HDMI/DisplayPort cable to the monitor’s DVI/
HDMI/DisplayPort port.
b. Connect the other end of the DVI/HDMI/DisplayPort cable to your
computer's DVI/HDMI/DisplayPort port.
c. Tighten the two screws to secure the DVI connector.
•
•
To connect the audio cable: connect one end of the audio cable to the
monitor’s Audio-in port, the other end to the computer’s audio-out port.
To use the earphone (only when an HDMI/DisplayPort cable is
connected): connect the end with plug type to the monitor’s earphone jack.
When these cables are connected, you can choose the desired signal from the
Input Select item in the OSD menu.
2.5
Turning on the monitor
Press the power button
. See page 1-2 for the location of the power button. The
power indicator lights up in blue to show that the monitor is ON.
ASUS VG248QE LCD Monitor
2-3
3.1
OSD (On-Screen Display) menu
3.1.1
How to reconfigure
1.
Press the MENU button to activate
the OSD menu.
2.
Press
and
to
navigate through the functions.
Highlight the desired function and
press the MENU button to activate
it. If the function selected has a sub-menu, press
and
again
to navigate through the sub-menu functions. Highlight the desired sub-menu
function and press the MENU button to activate it.
3.
4.
Press
To exit and save the OSD menu, press the
menu disappears. To adjust other functions, repeat steps 1-3.
and
to change the settings of the selected function.
button repeatedly until the OSD
3.1.2
OSD function introduction
1.
Splendid
This function contains six sub-
functions you can select for your
preference. Each mode has the
Reset selection allowing you to
maintain your setting or return to
the preset mode.
•
•
Scenery Mode: best choice for scenery photo display with SPLENDID™
Video Enhancement.
Standard Mode: best choice for document editing with SPLENDID™
Video Enhancement.
•
•
•
Theater Mode: best choice for movies with SPLENDID™ Video
Enhancement.
Game Mode: best choice for games playing with SPLENDID™ Video
Enhancement.
Night View Mode: best choice for dark-scene games or movies with
SPLENDID™ Video Enhancement.
•
sRGB: best choice for viewing photos and graphics from PCs.
In the Standard Mode, the ASCR, Saturation and Sharpness functions are
not user-configurable.
ASUS VG248QE LCD Monitor
3-1
2.
Color
You can adjust Brightness,
Contrast, Saturation, Color Temp.,
Skin Tone, and Smart View from
this menu.
•
Brightness: the adjusting
range is from 0 to 100.
is a hotkey to activate this
function.
•
•
•
Contrast: the adjusting range is from 0 to 100.
Saturation: the adjusting range is from 0 to 100.
Color Temp.: contains four modes including Cool, Normal, Warm, and
User Mode.
•
•
Skin Tone: contains three color modes including Reddish, Natural, and
Yellowish.
Smart View: provides better display quality under big viewing angle.
In the User mode, colors of R (Red), G (Green), and B (Blue) are user-
configurable; the adjusting range is from 0-100.
3.
Image
You can adjust Sharpness, Trace
Free, Aspect Control and ASCR,
from this menu.
•
•
•
Sharpness: the adjusting
range is from 0 to 100.
Trace Free: adjusts the
response time of the monitor.
Aspect Control: adjusts the
aspect ratio to “Full”, “4:3”, or “OverScan” (only available for the HDMI
input).
•
ASCR: turns on or off the ASCR (ASUS Smart Contrast Ratio) function.
(Only available at Scenery Mode, Theater Mode, Game Mode, and Night
View Mode.)
4.
Input Select
In this function, you can select your
desired input source.
3-2
Chapter 3: General Instructions
5.
System Setup
Allows you to adjust the system.
Splendid Demo Mode:
•
splits the screen into two for
Splendid modes comparison.
•
•
•
Volume: the adjusting range
is from 0 to 100.
ECO Mode: reduces power
consumption.
OSD Setup:
*
Adjusts the horizontal position (H-Position)/the vertical position
(V-Position) of the OSD from 0 to 100.
*
*
*
Adjusts the OSD timeout from 10 to 120 seconds.
Enables or disables the DDC/CI function.
Adjusts the OSD background from opaque to transparent.
•
•
Information: shows the monitor information.
Language: there are 21 languages for your selection, including English,
French, German, Italian, Spanish, Dutch, Portuguese, Russian, Czech,
Croatia, Polish, Romanian, Hungarian, Turkey, Simplified Chinese,
Traditional Chinese, Japanese, Korean, Thai, Indonesia, Persian.
All Reset: “Yes” allows you to restore the default settings.
•
ASUS VG248QE LCD Monitor
3-3
3.2
Specifications summary
Panel Type
Panel size
Max. Resolution
TFT LCD
24”W (16:9, 60.97 cm) wide screen
1920 x 1080
Pixel pitch
Brightness (Typ.)
0.270 mm
350 cd/m2
Contrast Ratio (Typ.)
Contrast Ratio (Max.)
Viewing angle(H/V) CR>10
Display colors
1000:1
80,000,000:1 (with ASCR on)
170˚/160˚
16.7 M
Response time
1 ms
SPLENDID™ Video Enhancement
SPLENDID™ selection
Color temperature selection
Skin-Tone selection
Digital input
Yes
6 video preset modes (by hotkey)
4 color temperatures
3 skin-tones
HDMI v1.4 x 1, DisplayPort v1.2 x 1, DVI (Dual-
Link) x 1
Audio-in port
Earphone jack
Colors
3.5 mm Mini-jack
Yes
Black
Speaker (Built-in)
Power LED
Tilt
2 W x 2 Stereo, RMS
Blue (On)/Amber (Standby)
+15˚~ -5˚
VESA wall mount
Kensington lock
Voltage rating
Power consumption
100 x 100 mm
Yes
AC: 100~240V
Power On: < 45 W, Standby: < 0.5 W,
Power Off: < 0.5 W
Temperature (Operating)
Temperature (Non-operating)
Dimensions (W x H x D)
0˚C~40˚C
-20˚C~+60˚C
569.4 mm x 499.9 mm x 231.0 mm (machine)
674 mm x 413 mm x 221 mm (package)
Weight (Esti.)
5.5 kg (Net); 8.1 kg (Gross)
Multi-languages
21 languages (English, French, German,
Italian, Spanish, Dutch, Portuguese, Russian,
Czech, Croatia, Polish, Romanian, Hungarian,
Turkey, Simplified Chinese, Traditional Chinese,
Japanese, Korean, Thai, Indonesia, Persian)
Accessories
DVI (Dual-Link) cable, audio cable, power cord,
Quick start guide, warranty card
3-4
Chapter 3: General Instructions
Regulation approvals
Energy Star®, CB, CE, Gost-R, CCC, UL/cUL,
FCC, C-Tick, BSMI, VCCI, RoHS, WEEE,
Hygenic, J-MOSS, ErP, PSE, UKrSEPRO,
Windows 7 WHQL, Windows 8 WHQL
*Specifications are subject to change without notice.
ASUS VG248QE LCD Monitor
3-5
3.3
Troubleshooting (FAQ)
Problem
Possible Solution
Power LED is not ON
•
•
Press the
is in the ON mode.
Check if the power cord is properly
connected to the monitor and the power
outlet.
button to check if the monitor
The power LED lights amber and there is
no screen image
•
•
•
•
Check if the monitor and the computer are
in the ON mode.
Make sure the signal cable is properly
connected the monitor and the computer.
Inspect the signal cable and make sure
none of the pins are bent.
Connect the computer with another
available monitor to check if the computer
is properly working.
Screen image is too light or dark
•
•
Adjust the Contrast and Brightness
settings via OSD.
Screen image is not centered or sized
properly
Adjust the H-Position or V-Position
settings via OSD.
Screen image bounces or a wave pattern is
present in the image
•
•
Make sure the signal cable is properly
connected to the monitor and the
computer.
Move electrical devices that may cause
electrical interference.
Screen image has color defects (white does • Inspect the signal cable and make sure
not look white)
that none of the pins are bent.
Perform All Reset via OSD.
Adjust the R/G/B color settings or select
the Color Temperature via OSD.
•
•
Screen image is blurry or fuzzy
•
•
Adjust the Phase and Clock settings via
OSD.
No sound or sound is low
Ensure that the HDMI cable is properly
connected to the monitor and the
computer.
•
•
Adjust the volume settings of both your
monitor and HDMI device.
Ensure that the computer sound card
driver is properly installed and activated.
3-6
Chapter 3: General Instructions
3.4
Supported operating modes
Resolution Frequency
640x350
Refresh Rate
70Hz
85Hz
60Hz
67Hz
75Hz
85Hz
70Hz
85Hz
56Hz
60Hz
72Hz
75Hz
85Hz
75Hz
60Hz
60Hz
70Hz
75Hz
85Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
75Hz
60Hz
60Hz
60Hz
60Hz
Horizontal
31.469KHz
640x350
37.861KHz
31.469KHz
35KHz
640x480
640x480
640x480
37.5KHz
640x480
43.269KHz
31.469KHz
37.927KHz
35.156KHz
37.897KHz
48.077KHz
46.875KHz
53.674KHz
49.725KHz
31.02KHz
48.363KHz
56.476KHz
60.023KHz
68.677KHz
67.5KHz
720x400
720x400
800x600
800x600
800x600
800x600
800x600
832x624
848x480
1024x768
1024x768
1024x768
1024x768
1152x864
1280x720
1280x720
1280x720
1280x768
1280x800
1280x800
1280x800
1280x960
1280x1024
1280x1024
1366x768
1440x900
1440x900
1440x900
1680x1050
1680x1050
1920x1080
1920x1080
44.444KHz
44.772KHz
56.456KHz
47.396KHz
49.306KHz
49.702KHz
62.795KHz
60KHz
63.981KHz
79.976KHz
47.712KHz
55.469KHz
55.935KHz
70.635KHz
64.674KHz
65.29KHz
66.587KHz
67.5KHz
ASUS VG248QE LCD Monitor
3-7
Resolution Frequency
1920x1080* (DVI/DP)
1920x1080* (DVI/DP)
1920x1080* (DVI/DP)
1920x1080* (DVIDP)
640x480P (HDMI)
Refresh Rate
85Hz
Horizontal
95.43KHz (2D)
144Hz
158.11KHz (2D)
113.3KHz (2D)/113.8KHz (3D)
137.2KHz (2D/3D)
31.469KHz/31.5KHz
31.469KHz/31.5KHz
31.25KHz
100Hz
120Hz
59.94/60Hz
59.94/60Hz
50Hz
720x480P (HDMI)
720x576P (HDMI)
1280x720P (HDMI)
1280x720P (HDMI)
1440x480P (HDMI)
1440x576P (HDMI)
1920x1080i (HDMI)
1920x1080i (HDMI)
1920x1080P (HDMI)
1920x1080P (HDMI)
50Hz
37.5KHz
59.94/60Hz
59.94/60Hz
50Hz
44.955KHz/45KHz
31.469KHz/31.5KHz
31.25KHz
50Hz
28.125KHz
59.94/60Hz
50Hz
33.716KHz/33.75KHz
56.25KHz
59.94/60Hz
67.433KHz/67.5KHz
Note: you must select one of the “*” timing for enabling 3D or 144Hz feature with a compatible
NVIDIA-GPU graphic card via Dual-link DVI cable connection.
3-8
Chapter 3: General Instructions
ASUS VG248QE LCD Monitor
3-9
|
