Acura Music Link BII31179 34943 User Manual

Accessory  
Application  
Publications No.  
BII 31179-34943  
INSTALLATION  
INSTRUCTIONS  
ACURA MUSIC LINK  
(FOR iPod®)  
2006 MDX  
Issue Date  
APRIL 2007  
PARTS LIST  
Music Link Adapter Kit (sold separately)  
P/N 08A28-1H2-100  
Attachment Kit (Sold Separately)  
P/N 08A28-1H1-800  
Music Link adapter unit  
4 Cushion tapes  
Bus cable  
Holder cushion  
Music Link harness  
Grommet  
CD-ROM  
8 Wire ties  
2 Long wire ties  
Quick Reference guide  
Y-Harness Adapter (sold separately)  
P/N 08A31-0F1-000  
Y-harness adapter  
08B28-S3V-2000-91  
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.  
BII 31179-34943 (0704)  
1 of 8  
6. Move the shift lever to the N position, then  
remove the coin box.  
9. While wearing gloves, reach under the center  
panel and release each of the three bottom clips.  
Carefully pull the center panel out toward you to  
release the ten clips. Unplug the vehicle  
COIN BOX  
CLIPS (2)  
connectors, and remove the center panel.  
CENTER  
PANEL  
LOWER  
TRIM  
CENTER  
PANEL  
CLIP  
MAT  
CLIPS (2)  
7. Remove the mat and center panel lower trim (four  
clips).  
CLIPS (10)  
VEHICLE  
CONNECTORS  
8. Open the accessory socket cover, and remove  
the center lower cover (four self-tapping screws,  
release the harness clip, and disconnect the  
accessory socket connector).  
ACCESSORY  
SOCKET  
CONNECTOR  
HARNESS  
CLIP  
ACCESSORY  
SOCKET  
COVER  
CENTER PANEL  
CENTER LOWER  
COVER  
SELF-TAPPING  
SCREWS  
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.  
BII 31179-34943 (0704)  
3 of 8  
10. Remove the two self-tapping screws and four bolts  
that secure the radio brackets. Pull the audio unit  
out toward you, unplug the six vehicle connectors  
and the antenna lead and remove the audio unit.  
12. Remove the weatherstrip. Remove the right front  
kick panel (one screw clip and one clip).  
WEATHERSTRIP  
VEHICLE  
CONNECTORS (6)  
SCREW  
CLIP  
SELF-TAPPING  
SCREWS  
BOLTS (4)  
RIGHT FRONT  
KICK PANEL  
ANTENNA  
CLIP  
AUDIO  
LEAD  
UNIT  
11. Remove the right front side step trim (four clips).  
13. Remove the glove box by removing the self-  
tapping screw from the damper rod, then release  
the two stoppers and remove the two bolts.  
CLIPS (4)  
RIGHT FRONT  
SIDE STEP TRIM  
STOPPER  
DAMPER  
ROD  
TAB  
SELF-TAPPING  
GLOVE  
BOX  
SCREW  
BOLTS  
4 of 8  
BII 31179-34943 (0704)  
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.  
14. Using a felt-tip pen, mark the Music Link harness  
as shown.  
18. Route the Music Link harness DIN connector into  
the 19 mm hole in the direction shown, and install  
the grommet to the 19 mm hole.  
CUSHION  
CUSHION  
TAPE  
TAPE  
GLOVE  
(Cut into 4 pieces.)  
MUSIC LINK  
HARNESS DIN  
CONNECTOR  
BOX  
FELT-TIP  
PEN  
MUSIC LINK  
HARNESS  
MARK  
900 mm  
50 mm  
50 mm  
GROMMET  
19 mm  
HOLE  
MUSIC LINK  
HARNESS  
MUSIC LINK  
HARNESS  
15. Route the Music Link harness through the  
grommet.  
GROMMET  
16. Cut one cushion tape into 4 equal pieces, and  
wrap two pieces of the cushion tapes to the Music  
Link harness at the measurements shown.  
19. Route the Music Link harness through the glove  
box opening to the audio unit opening.  
17. To prevent damage, wrap electrical tape around  
the drill bit at a point about 30 mm away from the  
tip. While wearing eye protection, drill a 19 mm  
(3/4 in.) hole through the marked location. Remove  
all burrs from the drilled hole.  
MUSIC LINK  
HARNESS  
AUDIO UNIT  
OPENING  
DRILL  
BIT  
30 mm  
ELECTRICAL  
TAPE  
PUSHPIN  
DRILL  
MOTOR  
3 mm  
DRILL BIT  
19 mm (3/4 in.)  
HOLE SAW  
GLOVE  
BOX  
GLOVE BOX  
OPENING  
RIB  
GLOVE  
BOX  
20 mm  
20 mm  
BII 31179-34943 (0704)  
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.  
5 of 8  
20. Insert the Music Link adapter unit into the unit  
cushion.  
22. Secure the Music Link adapter unit onto the  
instrument panel with two long wire ties.  
INSTRUMENT  
PANEL  
UNIT  
CUSHION  
MUSIC  
LINK  
SIDE VIEW  
ADAPTER  
UNIT  
FRONT  
MUSIC LINK  
ADAPTER  
UNIT  
INSTRUMENT  
PANEL  
AUDIO UNIT  
OPENING  
Align ends.  
MUSIC LINK  
ADAPTER  
UNIT  
LONG WIRE  
TIES  
21. Route the Music Link harness and bus cable  
through the audio unit opening, and connect the  
Music Link harness DIN connector (White) and  
bus cable DIN connector (Black) to the Music Link  
adapter assembly. Note the location of the  
connectors and the terminals.  
23. Secure the Music Link harness to the vehicle pipe  
with the two wire ties. (Align the mark you made in  
step 14 with the wire tie as shown).  
WIRE TIE  
VEHICLE  
PIPE  
MUSIC LINK  
BUS CABLE  
Align the mark you  
made in step 14 with  
the long wire tie.  
ADAPTER  
ASSEMBLY  
DIN CONNECTOR  
(BLACK)  
MUSIC LINK  
HARNESS  
DIN CONNECTOR  
(WHITE)  
WIRE  
VEHICLE  
TIE  
PIPE  
MUSIC  
LINK  
HARNESS  
MUSIC  
LINK  
HARNESS  
MUSIC  
GLOVE  
BOX  
LINK  
GLOVE BOX  
OPENING  
HARNESS  
AUDIO UNIT  
OPENING  
MUSIC LINK  
ADAPTER  
ASSEMBLY  
BUS CABLE  
6 of 8  
BII 31179-34943 (0704)  
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.  
24. Secure the bus cable:  
Bundle up the vehicle harness and secure it, the  
bus cable, and Y-harness adapter with two wire ties  
as shown.  
BUS CABLE  
(Bundle up  
excess.)  
Without the XM Radio: Align the bus cable 14-pin  
connector with the vehicle 20-pin connector,  
bundle up the excess bus cable, and secure it to  
the vehicle harness with the two wire ties.  
BUS CABLE  
WIRE  
TIES  
AUDIO UNIT  
(Bindle up  
OPENING  
excess.)  
VEHICLE  
HARNESS  
WIRE  
TIES  
WIRE  
TIES  
Y-HARNESS  
VEHICLE  
ADAPTER  
HARNESS  
Y-HARNESS  
ADAPTER 14-PIN  
CONNECTOR  
VEHICLE 20-PIN  
CONNECTOR  
(Align.)  
VEHICLE  
HARNESS  
Align the Y-harness adapter 14-pin connector with  
the vehicle 20-pin connector and bundle up the  
excess bus cable. Secure it to the vehicle harness  
with the two wire ties.  
VEHICLE 20-PIN  
CONNECTOR  
BUS CABLE  
14-PIN  
With XM Radio and Option CD Changer:  
Align.  
CONNECTOR  
Unplug the CD changer bus cable 14-pin connector  
and CD changer Y-harness adapter 14-pin  
connector. Connect the Y-harness adapter 14-pin  
connectors in between. Connect the bus cable  
14-pin connector to the Y-harness adapter 14-pin  
connector as shown.  
With the XM Radio:  
Connect the bus cable 14-pin connector and vehicle  
14-pin connector (for XM radio) to the Y-harness  
adapter 14-pin connector.  
Attach one cushon tape around each Y-harness  
adapter 14-pin connector.  
CD CHANGER  
Y-HARNESS  
ADAPTER 14-PIN  
CONNECTOR  
CD CHANGER  
BUS CABLE 14-PIN  
CONNECTOR  
BUS  
CABLE  
14-PIN  
CONNECTORS (2)  
BUS  
CABLE  
(Align.)  
BUS CABLE  
14-PIN  
CONNECTORS  
CUSHION  
TAPES (2)  
Y-HARNESS  
ADAPTER  
BUS CABLE 14-PIN  
CONNECTOR  
Y-HARNESS  
ADAPTER  
(Align.)  
14-PIN  
CONNECTOR  
Y-HARNESS  
ADAPTER  
CUSHION  
TAPES (2)  
14-PIN  
VEHICLE 14-PIN  
CONNECTOR  
(for XM radio)  
CONNECTORS (2)  
Attach one cushon tape around each Y-harness  
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.  
BII 31179-34943 (0704)  
7 of 8  
adapter 14-pin connectors.  
25. Reinstall the glove box.  
Secure the Y-harness adapter to the vehicle  
harness with a wire tie.  
26. Connect the vehicle connectors and bus cable  
14-pin connector (or Y-harness adapter 14-pin  
connector) to the audio unit, and reinstall the  
BUS CABLE  
VEHICLE  
(Bundle up excess.)  
HARNESS  
BUS CABLE 14-PIN  
VEHICLE  
CONNECTOR or  
Y-HARNESS ADAPTER  
CONNECTORS  
14-PIN CONNECTOR  
WIRE  
TIE  
SELF-TAPPING  
SCREW  
WIRE  
TIE  
VEHICLE  
HARNESS  
Y-HARNESS  
ADAPTER  
WIRE  
TIE  
BOLT (4)  
ANTENNA  
Bundle up the excess bus cable, and secure it to  
the vehicle harness with the two wire ties.  
AUDIO  
LEAD  
UNIT  
audio unit.  
27. Check that all wire harnesses are routed properly  
and all connectors are plugged in.  
STOPPER  
DAMPER  
ROD  
28. Reconnect the negative cable to the battery.  
29. Enter the client’s radio anti-theft code. Reset the  
radio station presets and the clock.  
TAB  
30. Reinstall all removed parts.  
31. Turn the audio unit ON. Check that CDC EJECT,  
or CD4 EJECT is shown on the audio unit display  
while in the AUX mode (the Music Link is  
recognized as an accessory CD changer).  
NOTE: Whenever the battery is disconnected, the  
driver’s AUTO function is disabled.  
SELF-TAPPING  
GLOVE  
32. Start the engine. Push down on the driver’s  
window switch until the window is fully open.  
SCREW  
BOX  
33. Pull up on the driver’s window switch fully to close  
the window completely, then hold the switch for  
2 seconds or more.  
BOLTS  
34. Test the window AUTO function.  
8 of 8  
BII 31179-34943 (0704)  
© 2007 American Honda Motor Co., Inc. - All Rights Reserved.  

Audiovox Car Video System LCM5043NP User Manual
BenQ G900A User Manual
Cisco Systems OL 6539 01 User Manual
Clarion M455A User Manual
Contemporary Research 232 FMA User Manual
Dual XDMA6355 User Manual
FujiFilm DS 505A User Manual
Hypertec 5703 User Manual
JVC 0609SKMLGEEGL User Manual
JVC GR FXM383 User Manual