The IR illuminator control buttons are located
on its side.
(OPTIONAL)
To use your MO5-2 with a 35mm camera or
camcorder you will need the following:
1) If you plan to use a camcorder, then your
camcorder must have a MACRO feature. Most
modern camcorders today have a MACRO fea-
ture built-in.
To switch the Digital IR illuminator on/off press
“+” and “-” buttons simultaneously. When the
IR illuminator is switched on you can see the
green LED lit.
By pushing the buttons “+” and “-” you may
adjust the IR brightness.
2) If you plan to use a 35mm camera, you will need
a MACRO lens. If you don’t have one, we advise
that you contact your local camera store.
3) You may or may not need a STEP-UP or
STEP-DOWN ring in order to adapt the camera
adapter to your lens.
NOTE: The camera adapter comes with 37mm
and 52mm threads. If you need other sizes your
local camera store should be able to help.
The IR beam is focusable to change the field of
coverage. To change the beam width slightly
turn the IR lens.
You may notice that beam of IR illuminator
might not shine directly in the middle of your
viewing image. You can change the direction of
the IR beam slightly in horizontal and vertical
directions with rotation of small screws on the
side of IR.
• Remove the rubber eyecup from the MO5-2
IR Brightness
IR Beam Direction
justment
• Screw the camera adapter onto the front of
the lens on your Video camera’s lens or your
35mm camera’s lens.
• Loosen the three set screws on the camera
adapter.
Focusing
• Place the camera adapter over the MO5-2’s
eyepiece.
• Tighten the three set screws to fit snugly to the
MO5-2’s eyepiece
• You may need to focus the 35mm camera or
video camera in combination with the MO5-2 in
order to get the sharpest possible image.
Battery
Housing
Fixation
Screw
IR Beam Direction
Horizontal Adjustment
You can also change the position of the IR
control panel fitting your needs. Undoing the
small set screw on back of IR. Then use the
included wrench to loosen back ring, Move the
IR to its desired position/angle, retighten ring
with wrench then retighten set screw.
• We suggest that you find an open space to work
in. Focus the MO5-2 so that the scene is at its
sharpest. For best results you should disable
the auto focus (if any) on either the 35mm
camera or the video camera and manually
focus the 35mm camera or the video camera.
Once the image is sharp, then simply adjust
the MO5-2’s front lens to change the focus.
STORAGE AND CARE
*An important part to remember is that you are
not taking a picture of an object that is far away
from you, but you are actually taking a picture
of the phosphorous screen of the MO5-2 that is
only 2-3 inches away.
• If the device is not to be us d for extended
period of time (more than 10 days) remove the
battery.
• Avoid touching lenses. If fingerprints or traces
of dirt or dust appear, clean their surface with
a Photographic lens cleaning tissue.
INFRA-RED ILLUMINATOR
• Keep lens cap/daylight filter on when not in use.
Infra-red (IR) Illuminators are common for
night vision technology. The IR light greatly
enhances the performance of your scope,
while remaining almost totally invisible to the
naked eye. In a dark environment, power up
the scope and observe a scene with the IR
off. Then observe the same scene with the
IR on. Note the difference in illumination. It is
important to remember that the IR illuminator
is simply an infra red light source, and like any
light source it may loose its effectiveness over
a great distance.
• The MO5-2 is not harmful to the user or the
environment.
• Do not disassemble except to clean the front lens
and eyepiece: it will void your warranty.
• Evaluate the monocular function by looking
through it in a lit environment with the daylight
filter lens cap on. Never use in daylight without
the daylight filter lens cap on.
• Never point the MO5-2 at a bright light source.
• Adverse atmospheric conditions such as fog,
smog or haze and a lack of ambient light
(moon or starlight) may diminish the effective
viewing distance.
To fix the IR Illuminator to the scope screw the
fixation screw on the IR into the thread on the
body.
2
LIMITATION OF LIABILITY
ATN will not be liable for any claims, actions, suits,
proceedings, costs, expenses, damages or liabili-
ties arising out of the use of this product. Operation
and use of the product are the sole responsibility of
the Customer. ATN’s sole undertaking is limited to
providing the products and services outlined herein
in accordance with the terms and conditions of this
Agreement. The provision of products sold and serv-
ices performed by ATN to the Customer shall not be
interpreted, construed or regarded, either expressly
or implied, as being for the benefit of or creating any
obligation toward any third party of legal entity out-
side ATN and the Customer; ATN’s obligations under
this Agreement extend solely to the Customer. ATN’s
liability hereunder for damages, regardless of
the form or action, shall not exceed the fees or
other charges paid to ATN by the customer or
customer’s dealer. ATN shall not, in any event,
be liable for special, indirect, incidental or con-
sequential damages, including, but not limited to,
lost income, lost revenue or lost profit, whether
such damages were foreseeable or not at the
time of purchase, and whether or not such dam-
ages arise out of a breach of warranty, a breach
of agreement, negligence, strict liability or any
other theory of liability.
Q: Flashes, flickers or clicking occur while
operating
S: If it occurs within the first five minutes of
inserting new batteries, it is normal and the
device will resume normal operation soon
thereafter. If it occurs for more than 10 min-
utes, contact for service instructions.
Q: Dark spots on screen.
S: These are either cosme tic blemishes in the
intensifier tube or dust particles.
Q: Screen becomes darker than at previous use.
S: Replace batteries. If problem persists, con-
tact your dealer or other authorized service
representative for service instructions.
Q: Image not clear.
S: Adjust objective lens, and/or the eyepiece.
This product is guaranteed to be free from manufac-
turing defects in material and workmanship under
normal use for a period of 2 (two) years from the date
of purchase. In the event a defect that is covered by
the foregoing warranty occurs during the applicable
period stated above, ATN, at its option, will either
repair or replace the product, and such action on the
part of ATN shall be the full extent of ATN’s liability,
and the Customer’s sole and exclusive remedy. This
warranty does not cover a product (a) used in other
than its normal and customary manner; (b) subjected
to misuse; (c) subjected to alterations, modifications
or repairs by the Customer of by any party other than
ATN without prior written consent of ATN; (d) special
order or “close-out” merchandise or merchandise
sold “as-is” by either ATN or the ATN dealer; or (e)
merchandise that has been discontinued by the
manufacturer and either parts or replacement units
are not available due to reasons beyond the control
of ATN. ATN shall not be responsible for any defects
or damage that in ATN’s opinion is a result from the
mishandling, abuse, misuse, improper storage or
improper operation, including use in conjunction
with equipment which is electrically or mechanically
incompatible with or of inferior quality to the product,
as well as failure to maintain the environmental condi-
tions specified by the manufacturer. CUSTOMER IS
HEREBY NOTIFIED THAT OPERATION OF THE
EQUIPMENT DURING DAYLIGHT HOURS OR
UNDER ANY EXCESSIVE LIGHT CONDITIONS
MAY PERMANENTLY DAMAGE THE INTERNAL
COMPONENTS OF THE UNIT AND SAID DAMAGE
WILL NOT BE COVERED UNDER THIS WAR-
RANTY. This warranty is extended only to the original
purchaser. Anybreachofthiswarrantyshallbewaived
unless the customer notifies ATN at the address noted
below within the applicable warranty period.
PRODUCT WARRANTY REGISTRATION
In order to validate the warranty on your product, ATN
must receive a completed Product Warranty Regis-
tration Card for each unit. Please complete the form
below and immediately mail it to our Service Center:
ATN Corporation, 20 South Linden Ave., Suite 1B,
South San Francisco CA 94080. Products qualifying
for warranty repair will be either repaired or replaced
within 10 business days of receipt of merchandise
unless the customer is notified otherwise.
OBTAINING WARRANTY SERVICE
To obtain warranty service on your unit, take or send
the product, postage paid, with a copy of your sales
receipt to our service center, ATN Corporation at the
address noted above. All merchandise must be fully
insured with the correct postage; ATN will not be
responsible for improper postage or, missing or dam-
aged merchandise during shipment.
For customer service and technical support, please
contact
American Technologies Network Corp.
North American Office
20 S. Linden Ave. Suite 1B,
South San Francisco, CA 94080
phone: 800-910-2862, 650-875-0130;
fax: 650-875-0129
European Office
phone: 44(0)870-0111286,
fax: 44(0) 845-3349142
The customer understands and agrees that except
for the foregoing warranty, no other warranties writ-
ten or oral, statutory, expressed or implied, including
any implied warranty of merchantability or fitness for
a particular purpose, shall apply to the product. All
such implied warranties are hereby and expressly
disclaimed.
The following countries can use our
toll free number 00 800 9102-8620
Austria, France, Germany, Holland, Italy,
Spain, Sweden, Switzerland
|