1700 PSI / 1.2 GPM
ELECTRIC PRESSURE WASHER
GPW 1702
OPERATOR’S MANUAL
TOLL-FREE HELPLINE: 1-888-90WORKS (888.909.6757)
Read all safety rules and instructions carefully before operating this tool.
IMPORTANT SAFETY INTRODUCTIONS
W A R N I N G
Read and understand all instructions. Failure to follow all instructions listed below may result in electric
VKRFNꢀꢁ¿UHꢀꢁDQGꢁꢂRUꢁVHULRXVꢁSHUVRQDOꢁLQMXU\ꢃ
W A R N I N G
When using this product, basic precaution should always be followed, including the following.
READ ALL INSTRUCTIONS BEFORE USING THIS PRODUCT
Ŷ
Ŷ
Ŷ
7RꢁUHGXFHꢁWKHꢁULVNꢁRIꢁLQMXU\ꢀꢁFORVHꢁVXSHUYLVLRQꢁLVꢁQHFHVVDU\ꢁZKHQꢁDꢁSURGXFWꢁLVꢁXVHGꢁQHDUꢁFKLOGUHQꢃ
Be thoroughly familiar with controls. Know how to stop the product and release pressure quickly.
Stay alert and exercise control. Watch what you are doing and use common sense. Do not operate the
product when you are tired. Do not rush.
Ŷ
Ŷ
Ŷ
Ŷ
Do not operate the product while under the influence of drugs, alcohol, or any medication.
Keep the area of operation clear of all people, particularly small children, and pets.
Don’t overreach or stand on unstable support. Keep proper footing and balance at all times.
Follow the maintenance instructions specified in this manual.
W A R N I N G
5LVNꢁRIꢁLQMHFWLRQꢁRUꢁLQMXU\ꢁ±ꢁ'RꢁQRWꢁGLUHFWꢁGLVFKDUJHꢁVWUHDPꢁDWꢁSHRSOHꢁRUꢁDQLPDOVꢃ
GROUND FAULT CIRCUIT INTERRUPTER PROTECTION
This pressure washer is provided with a ground fault circuit interrupter (GFCI) built into the plug of the
power supply cord. This device provides additional protection from the risk of electric shock. Should
replacement of the plug or cord become necessary, use only identical replacement parts that include
GFCI protection.
SERVICING OF A DOUBLE-INSULATED APPLIANCE
In a double-insulated product, two systems of insulation are provided instead of grounding. No
grounding means is provided on a double-insulated product, nor should a means for grounding be
added to the product. Servicing a double insulated product requires extreme care and knowledge of the
system, and should be done only by qualified service personnel. Replacement parts for a double
insulated product must be identical to the parts they replace. A double insulated product is marked with
the words “DOUBLE INSULATION” or “DOUBLE INSULATED.”The symbol
the product.
may also be marked on
EXTENSION CORDS
Ŷ
Do not use with extension cord. Plug directly into receptacle.
W A R N I N G
To reduce the risk of electrocution, keep all connections dry and off the ground. Do not touch plug with
wet hands.
EN - 3
SPECIFIC SAFETY RULES
Ŷ
Ŷ
Ŷ
Ŷ
Know your product. Read the operator’s manual carefully. Learn the machine’s applications and
limitations as well as the specific potential hazards related to this product.
To reduce the risk of injury, keep children and visitors away. All visitors should wear safety
glasses and be kept a safe distance from the work area.
Use the right product for the job.ꢁ'RQ¶WꢁIRUFHꢁWKHꢁSURGXFWꢁRUꢁWKHꢁDWWDFKPHQWVꢁWRꢁGRꢁDꢁMREꢁLWꢁZDVꢁQRWꢁ
designed for. Don’t use it for a purpose not intended.
Dress properly.ꢁ'RꢁQRWꢁZHDUꢁORRVHꢁFORWKLQJꢀꢁJORYHVꢀꢁQHFNWLHVꢀꢁRUꢁMHZHOOHU\ꢃꢁ7KH\ꢁFDQꢁJHWꢁFDXJKWꢁDQGꢁ
draw you into moving parts. Rubber gloves and nonskid footwear are recommended when working
outdoors. Also wear protective hair covering to contain long hair.
Ŷ
Do not operate the equipment while barefoot or when wearing sandals or similar lightweight
footwear. Wear protective footwear that will protect your feet and improve your footing on slippery
surfaces.
Ŷ
Ŷ
Exercise caution to avoid slipping or falling.
Always wear eye protection with side shields marked to comply with ANSI Z87.1. Following
WKLVꢁUXOHꢁZLOOꢁUHGXFHꢁWKHꢁULVNꢁRIꢁVHULRXVꢁSHUVRQDOꢁLQMXU\ꢃ
Ŷ
Ŷ
Use only recommended accessories.ꢁ7KHꢁXVHꢁRIꢁLPSURSHUꢁDFFHVVRULHVꢁPD\ꢁFDXVHꢁULVNꢁRIꢁLQMXU\ꢃ
Check damaged parts. Before further use of the product, all parts should be carefully checked to
determine that they will operate properly and perform their intended function. Check for alignment
of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that
may affect its operation. A guard or other part that is damaged must be properly repaired or replaced
E\ꢁDQꢁDXWKRUL]HGꢁVHUYLFHꢁFHQWHUꢁWRꢁDYRLGꢁULVNꢁRIꢁSHUVRQDOꢁLQMXU\ꢃ
Ŷ
Never leave product running unattended. Turn power off. Do not leave the product until it comes
to a complete stop.
Ŷ
Ŷ
Keep the motor free of grass, leaves, or grease to reduce the chance of a fire hazard.
Follow manufacturer’s recommendations for safe loading, unloading, transport, and storage
of machine.
Ŷ
Ŷ
Ŷ
Keep product dry, clean, and free from oil and grease. Always use a clean cloth when cleaning.
Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean product.
Check the work area before each use.ꢁ5HPRYHꢁDOOꢁREMHFWVꢁVXFKꢁDVꢁURFNVꢀꢁEURNHQꢁJODVVꢀꢁQDLOVꢀꢁZLUHꢀꢁ
or string which can be thrown by the machine.
Do not use product if switch does not turn it off. Have defective switches replaced by an
authorized service center.
Ŷ
Ŷ
Avoid dangerous environment. Don’t expose to rain. Keep work area well lit.
Do not abuse the cord. Never use the cord to carry the product or to disconnect the plug from
an outlet. Keep cord away from heat, oil, sharp edges, or moving parts. Replace damaged cords
immediately. Damaged cords increase the risk of electric shock.
Ŷ
Ŷ
Ground Fault Circuit Interrupter (GFCI) protection should be provided on the circuit(s) or
outlet(s) to be used for the product. Receptacles are available having built-in GFCI protection and
may be used for this measure of safety.
To reduce the risk of electric shock, this product has a polarized plug (one blade is wider
than the other) and will require the use of a polarized extension cord. The plug will fit into a
polarized extension cord only one way. If the plug does not fit fully into the extension cord, reverse
the plug. If the plug still does not fit, obtain a correct polarized extension cord. A polarized extension
cord will require the use of a polarized wall outlet. This plug will fit into the polarized wall outlet only
one way. If the plug does not fit fully into the wall outlet, reverse the plug. If the plug still does not
fit, contact a qualified electrician to install the proper wall outlet. Do not change the equipment plug,
extension cord receptacle, or extension cord plug in any way.
EN - 4
SPECIFIC SAFETY RULES
Ŷ
Ŷ
Make sure your extension cord is in good condition. When using an extension cord, be sure to
use one heavy enough to carry the current your product will draw. A wire gauge size (A.W.G.) of
at least 14 is recommended for an extension cord 25 feet or less in length. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier the cord. An undersized cord will cause
a drop in line voltage resulting in loss of power and overheating.
Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free
from oil or grease.
Ŷ
Ŷ
Never direct a water stream toward people or pets, or any electrical device.
Before starting any cleaning operation, close doors and windows. Clear the area to be cleaned
RIꢁGHEULVꢀꢁWR\VꢀꢁRXWGRRUꢁIXUQLWXUHꢀꢁRUꢁRWKHUꢁREMHFWVꢁWKDWꢁFRXOGꢁFUHDWHꢁDꢁKD]DUGꢃ
Ŷ
Do not use acids, alkalines, solvents, flammable material, bleaches, or industrial grade
solutions in this product. 7KHVHꢁSURGXFWVꢁFDQꢁFDXVHꢁSK\VLFDOꢁLQMXULHVꢁWRꢁWKHꢁRSHUDWRUꢁDQGꢁ
irreversible damage to the machine.
W A R N I N G
High pressure jets can be dangerous if subject to misuse.ꢁ7KHꢁMHWꢁPXVWꢁQRWꢁEHꢁGLUHFWHGꢁDWꢁSHRSOHꢀꢁ
animals, electrical devices, or the machine itself.
Ŷ
Ŷ
Keep the motor away from flammables and other hazardous materials.
Check bolts and nuts fixing the pressure washer shell for looseness before each use. A loose
bolt or nut may cause serious motor problems.
Ŷ
Ŷ
Before storing, allow the motor to cool.
When servicing use only identical replacement parts. Use of any other parts may create a
hazard or cause product damage.
Ŷ
Ŷ
Ŷ
Ŷ
ONLY use cold water.
Make sure minimum clearance of 3 feet is maintained from combustible materials.
Connect pressure washer only to an individual branch circuit.
Hold the handle and wand securely with both hands. Expect the trigger handle to move when
WKHꢁWULJJHUꢁLVꢁSXOOHGꢁGXHꢁWRꢁUHDFWLRQꢁIRUFHVꢃꢁ)DLOXUHꢁWRꢁGRꢁVRꢁFRXOGꢁFDXVHꢁORVVꢁRIꢁFRQWUROꢁDQGꢁLQMXU\ꢁWRꢁ
yourself and others.
Ŷ
Save these instructions. Refer to them frequently and use them to instruct other users. If you loan
someone this product, loan them these instructions also.
W A R N I N G
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities
contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are:
‡ꢁ/HDGꢁIURPꢁOHDGꢄEDVHGꢁSDLQWV
‡ꢁ&U\VWDOOLQHꢁVLOLFDꢁIURPꢁEULFNVꢁDQGꢁFHPHQWꢁDQGꢁRWKHUꢁPDVRQU\ꢁSURGXFWV
‡ꢁ$UVHQLFꢁDQGꢁFKURPLXPꢁIURPꢁFKHPLFDOO\ꢄWUHDWHGꢁOXPEHUꢁ
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your
exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment,
VXFKꢁDVꢁWKRVHꢁGXVWꢁPDVNVꢁWKDWꢁDUHꢁVSHFLDOO\ꢁGHVLJQHGꢁWRꢁ¿OWHUꢁRXWꢁPLFURVFRSLFꢁSDUWLFOHV.
W A R N I N G
This hose contains chemical(s) including lead, known to the State of California to cause cancer, birth
defects, and other reproductive harm. Do not drink water from this hose. Wash hands after use.
EN - 5
SYMBOLS
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.
SYMBOL
NAME
'(6,*1$7,21ꢂ(;3/$1$7,21
Voltage
V
A
Volts
Amperes
Hertz
Current
Hz
W
no
Frequency (cycles per second)
Power
Watt
No Load Speed
Alternating Current
Rotational speed, at no load
Type of current
Revolutions, strokes, surface speed, orbits
etc., per minute
ꢃꢃꢃꢂPLQ
Per Minute
Class II Construction
Safety Alert
Double-insulated construction
,QGLFDWHVꢁDꢁSRWHQWLDOꢁSHUVRQDOꢁLQMXU\ꢁKD]DUGꢃ
7RꢁUHGXFHꢁWWKHꢁULVNꢁRIꢁLQMXU\ꢀꢁXVHUꢁPXVWꢁUHDGꢁ
and understand operator’s manual before
using this product.
Read Operator’s Manual
Eye Protection
Always wear eye protection with side shields
marked to comply with ANSI Z87.1.
Do not expose to rain or use in damp
locations.
Wet Conditions Alert
7RꢁUHGXFHꢁWKHꢁULVNꢁRIꢁLQMHFWLRQꢁRUꢁLQMXU\ꢀꢁQHYHUꢁ
direct a water system towards people or pets
or place any body part in the stream. Leaking
hoses and fittings are also capable of causing
LQMHFWLRQꢁLQMXU\ꢃꢁ'RꢁQRWꢁKROGꢁKRVHVꢁRUꢁILWWLQJVꢃ
5LVNꢁRIꢁ,QMHFWLRQ
7RꢁUHGXFHꢁWKHꢁULVNꢁRIꢁLQMXU\ꢁIURPꢁNLFNEDFNꢀꢁ
hold the spray wand securely with both hands
when the machine is on.
Kickback
Failure to use in dry conditions and to
observe safe practices can result in electric
shock.
Electric Shock
7RꢁUHGXFHꢁWKHꢁULVNꢁRIꢁLQMXU\ꢁRUꢁGDPDJHꢀꢁ'2ꢁ
NOT USE ACIDS, ALKALINES, BLEACHES,
SOLVENTS, FLAMMABLE MATERIAL, OR
INDUSTRIAL GRADE SOLUTIONS in this
product.
Chemical Burns
EN - 6
SYMBOLS
The following signal words and meanings are intended to explain the levels of risk associated
with this product.
SYMBOL
SIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not
DANGER
DYRLGHGꢀꢁZLOOꢁUHVXOWꢁLQꢁGHDWKꢁRUꢁVHULRXVꢁLQMXU\ꢃ
Indicates a potentially hazardous situation, which, if not
DYRLGHGꢀꢁFRXOGꢁUHVXOWꢁLQꢁGHDWKꢁRUꢁVHULRXVꢁLQMXU\ꢃ
WARNING
Indicates a potentially hazardous situation, which, if not
DYRLGHGꢀꢁPD\ꢁUHVXOWꢁLQꢁPLQRUꢁRUꢁPRGHUDWHꢁLQMXU\ꢃ
CAUTION
CAUTION
(Without Safety Alert Symbol) Indicates a situation that may
result in property damage.
SERVICE
6HUYLFLQJꢁUHTXLUHVꢁH[WUHPHꢁFDUHꢁDQGꢁNQRZOHGJHꢁDQGꢁVKRXOGꢁEHꢁSHUIRUPHGꢁRQO\ꢁE\ꢁDꢁTXDOL¿HG
service technician. For service, return the product to your nearest AUTHORIZED
SERVICE CENTER for repair. When servicing, use only identical replacement parts.
W A R N I N G
7RꢁDYRLGꢁVHULRXVꢁSHUVRQDOꢁLQMXU\ꢀꢁGRꢁQRWꢁDWWHPSWꢁWRꢁXVHꢁWKLVꢁSURGXFWꢁXQWLOꢁ\RXꢁUHDGꢁWKRURXJKO\ꢁDQGꢁ
understand completely the operator’s manual. If you do not understand the warnings and instructions in
the operator’s manual, do not use this product. Call GREENWORKS customer service for assistance.
7KHꢁRSHUDWLRQꢁRIꢁDQ\ꢁSRZHUꢁWRROꢁFDQꢁUHVXOWꢁLQꢁIRUHLJQꢁREMHFWVꢁEHLQJꢁWKURZQꢁLQWRꢁ\RXUꢁH\HVꢀꢁ
which can result in severe eye damage. Before beginning power tool operation, always wear
safety goggles or safety glasses with side shields and, when needed, a full face shield. We
recommend Wide Vision Safety Mask for use over eyeglasses or standard safety glasses with
side shields. Always use eye protection which is marked to comply with ANSI Z87.1.
EN - 7
ELECTRICAL
W A R N I N G
The double insulated system is intended to protect the user from shock resulting from a break in the
product’s internal insulation. Observe all normal safety precautions to avoid electrical shock.
DOUBLE INSULATED
Double insulation is a concept in safety in electric power tools, which eliminates the need for the usual
three-wire grounded power cord. All exposed metal parts are isolated from the internal metal motor
components with protecting insulation. Double insulated products do not need to be grounded.
NOTE: Servicing of a product with double insulation requires extreme care and knowledge of the
system and should be performed only by a qualified service technician. For service, we suggest you
return the product to your nearest authorized service center for repair. Always use identical replacement
parts when servicing.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should be connected to a power supply that is 120
volts, 60 Hz, AC only (normal household current). Do not operate this product on direct current (DC). A
substantial voltage drop will cause a loss of power and the motor will overheat. If the product does not
operate when plugged into an outlet, double check the power supply.
Power Cord
Drip Loop
Fig. 1
GROUND FAULT CIRCUIT INTERRUPTER
This unit is equipped with a Ground Fault Circuit Interrupter (GFCI), which guards against the hazards
RIꢁJURXQGꢁIDXOWꢁFXUUHQWVꢃꢁ$QꢁH[DPSOHꢁRIꢁJURXQGꢁIDXOWꢁFXUUHQWꢁLVꢁWKHꢁFXUUHQWꢁWKDWꢁZRXOGꢁÀRZꢁWKURXJKꢁDꢁ
person who is using an appliance with faulty insulation and, at the same time, is in contact with an
HOHFWULFDOꢁJURXQGꢁVXFKꢁDVꢁDꢁSOXPELQJꢁ¿[WXUHꢀꢁZHWꢁÀRRUꢀꢁRUꢁHDUWKꢃꢁ*)&,ꢁSOXJVꢁGRꢁQRWꢁSURWHFWꢁDJDLQVWꢁVKRUWꢁ
circuits, overloads, or shocks.
EN - 8
KNOW YOUR PRESSURE WASHER
The safe use of this product requires an understanding of the information on the tool and in this
RSHUDWRU¶VꢁPDQXDOꢀꢁDVꢁZHOOꢁDVꢁDꢁNQRZOHGJHꢁRIꢁWKHꢁSURMHFWꢁ\RXꢁDUHꢁDWWHPSWLQJꢃꢁ%HIRUHꢁXVLQJꢁWKLVꢁSURGXFWꢀꢁ
familiarize yourself with all operating features and safety rules. (See Figure 2.)
Handle
High Pressure Hose
Trigger Handle
Trigger with Lock-out
GFCI
21ꢂ2))ꢁ6ZLWFK
Spray Tips
Water Intake
Water Outlet
Wheel
Detergent Tank
Fig. 2
DETERGENT TANK
Used for the application of pressure washer detergent.
GFCI PLUG
The pressure washer is equipped with a GFCI plug to guard against the hazards of ground fault
currents. This plug does not protect against short circuits, overloads, or shocks.
HIGH PRESSURE HOSE STORAGE
Reel the high pressure hose up in order to store the hose when not in use.
ON / OFF SWITCH
This switch turns the pressure washer on and off.
TRIGGER HANDLE
The trigger handle has a gripping surface that provides added control of the spray wand and helps
reduce fatigue.
TRIGGER WITH LOCK-OUT
Pulling the trigger releases a stream of water for high pressure cleaning. The lock-out provides
protection against accidental start up.
WATER INTAKE
Attach the garden hose to the water intake.
WATER OUTLET
Attach the High Pressure Hose to the water outlet.
EN - 9
PACKING LIST
PART NAME
ERP NO.
FIGURE
QTY
‡ꢁPressure Washer
1
(including the spray tips)
25°Spray Tip
40°Spray Tip
‡ꢁ7ULJJHUꢁ+DQGOH
321091835
1
‡ꢁ:DQGꢁ$VVHPEO\
312011639
31103973
1
1
‡ꢁꢅꢆꢁft. High Pressure Hose
1
‡ꢁ'HWHUJHQWꢁ7DQN
31111368
1
1
‡ꢁSpray Tip Cleaning Tool
33201671
‡ꢁGun holder
341231630
WARNING:
S
Insert the gun holder into the slot until it locks
into its tabs.
Set-up
1
2
1700 PSI / 1.2 GPM
ELECTRIC PRESSURE WASHER
GPW 1702
INSTALLING DETERGENT BOTTLE
Insert the male end of the bottle into the female outlet on the
trigger handle.
While pushing in the bottle firmly, turn clockwise until tabs lock
4
into place to ensure
Unscrew the bottle from the assembly and fill with pressure
washer detergents/soaps only.
a
leak-free connection.
5
SPRA
Y
TIP
SPRA
Y
TIP APPLICATION
6
1
1
120
‡ꢁꢁ4XLFNꢁ6WDUWꢁ*XLGH
‡ꢁꢁ2SHUDWRU¶Vꢁ0DQXDO
388011835
388021835
Green
-
Narrow fan tip (25°
)
The green pressure washer tip provides high versatility with its
25 degree angle tip. Referred to as the washing tip, because it
provides adequate pressure to remove dirt from surfaces, but is
designed to not damage many surfaces. This pressure washer tip is
designed for “sweeping” foliage or debris given its wide angle. This
20S
O
25
7
tip is versatile due to its wide area of cleaning and strong pressure
application.
White Wide fan tip (40°
-
)
The white 40 degree tip, referred to as the “fan” tip creates the
widest area of cleaning with relatively low pressure. This pressure
washer tip is best used for light or delicate cleaning applications. It
is recommended for light cleaning on wood decks and other soft or
delicate surfaces.
O
40
8
IMPORTANT
:
O
N
N
E
T
I
N
G
D
E
S
I
R
E
D
S
P
R
A
T
I
P
2
NOTE:
U
ull back the quick-connect collar
ush the spray tip into place
ush the collar forward
A
T
O
O
N
/
O
F
F
S
W
I
T
C
H
:
T
h
i
s
P
r
e
s
s
u
r
e
w
a
s
h
e
r
i
s
Do Not Return to Store
Call 1-888-909-6757
equipped with an Auto Start/Stop feature.
operate: urn the power switch to the On (I) position.
Pump will pressurize and shut down immediately
:
T
o
T
.
Once the trigger of the gun is depressed the unit will
turn on. Unit will shut off and be in standby mode when
trigger is released.
01
)
(888.909.6757
e
o
p
e
r
a
t
i
n
g
t
h
i
s
t
o
o
l
.
ASHER
W
2
s
c
a
r
e
f
u
l
l
y
b
e
f
o
r
170
O
R
’
S
M
A
N
U
A
L
T
A
GPW
.greenworkstools.com
www
1
7
0
0
P
S
I
/
1
.
2
G
P
M
OPER
E
L
E
C
T
R
I
C
P
R
E
S
S
U
R
E
L
L
-
F
R
E
E
H
E
L
P
L
I
N
E
:
1
-
8
8
8
-
9
0
W
O
R
K
S
O
T
R
e
a
d
a
l
l
s
a
f
e
t
y
r
u
l
e
s
a
n
d
i
n
s
t
r
u
c
t
i
o
n
EN - 10
ASSEMBLY
UNPACKING
This product requires assembly.
Ŷ
Carefully remove the product and any accessories from the box. Make sure that all the contents from
the packaging list are included.
W A R N I N G
Do not use this product if any parts on the Packing List are already assembled to your product when you
unpack it. Parts on this list are not assembled to the product by the manufacturer and require customer
installation. Use of a product that may have been improperly assembled could result in serious personal
LQMXU\ꢃ
Ŷ
Ŷ
Inspect the product carefully to make sure no breakage or damage occurred during shipping.
Do not discard the packing material until you have carefully inspected and satisfactorily operated the
product.
Ŷ
If any parts are damaged or missing, please call 1-888-909-6757 for assistance.
W A R N I N G
If any parts are damaged or missing do not operate this product until the parts are replaced. Use of this
SURGXFWꢁZLWKꢁGDPDJHGꢁRUꢁPLVVLQJꢁSDUWVꢁFRXOGꢁUHVXOWꢁLQꢁVHULRXVꢁSHUVRQDOꢁLQMXU\ꢃ
W A R N I N G
Do not connect to power supply until assembly is complete. Failure to comply could result in accidental
VWDUWLQJꢁDQGꢁSRVVLEOHꢁVHULRXVꢁSHUVRQDOꢁLQMXU\ꢃ
W A R N I N G
Do not attempt to modify this product or create accessories not recommended for use with this product.
Any such alteration or modification is misuse and could result in a harzardous condition leading to
SRVVLEOHꢁVHULRXVꢁSHUVRQDOꢁLQMXU\ꢃ
EN - 11
ASSEMBLY
ASSEMBLING THE GUN HOLDER (See Figure 3.)
Insert the gun holder into the slot until it locks into its tabs.
Ŷ
Fig. 3
ASSEMBLING THE PRESSURE WASHER GUN
Ŷ
Insert the male end (A) of the wand into the female bayonet outlet (B) firmly. (See Figure 4-1.)
Ŷ
While pushing in the wand firmly, turn clockwise until tabs lock into place to ensure a leak-free
connection. (See Figure 4-2.)
A
B
Fig. 4-1
Fig. 4-2
EN - 12
ASSEMBLY
CONNECTING HIGH PRESSURE HOSE TO THE TRIGGER HANDLE (See Figure 5.)
Ŷ
Connect the high pressure hose to the pressure washer gun assembly by turning the fitting clockwise.
Ensure the fitting is fully tightened to the pressure washer gun.
NOTE: For easier installation of the hose to the unit or trigger it is suggested to add pressure washer or
dish detergent to the rubber seal at each end of the hose. This will allow for easier installation and a snug
fit.
Collar
High Pressure Hose
Inlet Coupler
Fig. 5
DETERGENT TANK
Ŷ
Insert the male end of the bottle into the female outlet on the trigger handle. (See Figure 6-1.)
Ŷ
While pushing in the bottle firmly, turn clockwise until tabs lock into place to ensure a leak-free
connection. (See Figure 6-2.)
Ŷ
8QVFUHZꢁWKHꢁERWWOHꢁIURPꢁWKHꢁDVVHPEO\ꢁDQGꢁILOOꢁZLWKꢁSUHVVXUHꢁZDVKHUꢁGHWHUJHQWVꢂVRDSVꢁRQO\ꢃ
Fig. 6-1
Fig. 6-2
EN - 13
ASSEMBLY
CONNECTING THE GARDEN HOSE (See Figure 7.)
C A U T I O N :
Always observe all local regulations when connecting hoses to the water main. Some areas have
restrictions against connecting directly to public drinking water supply to prevent the feedback of
FKHPLFDOVꢁLQWRꢁWKHꢁGULQNLQJꢁZDWHUꢁVXSSO\ꢃꢁ'LUHFWꢁFRQQHFWLRQꢁWKURXJKꢁDꢁUHFHLYHUꢁWDQNꢁRUꢁEDFNꢁÀRZꢁ
preventer is usually permitted.
The water supply must come from a water main. NEVER use hot water or water from pools, lakes, etc.
Before connecting the garden hose:
Ŷ
Ŷ
Ŷ
Ŷ
Ŷ
Ŷ
Uncoil the garden hose.
Run the water hose until a steady stream of water appears to clean any debris from the hose.
Inspect the screen in the water intake for any damage or build up of debris.
If the screen is damaged, do not use the machine until the screen has been replaced.
If the screen is dirty, clean it before connecting the garden hose to the machine.
With the hose faucet turned completely off, attach the end of the garden hose to the water intake.
Tighten by hand.
Fig. 7
W A R N I N G
Always ensure that the garden hose is connected to the unit and that the faucet is turned on, before the
power to the unit is switched on. Pump damage will occur if these steps are not followed.
EN - 14
OPERATION
W A R N I N G
Do not allow familiarity with the product to make you careless. Remember that a careless fraction of a
VHFRQGꢁLVꢁVXI¿FLHQWꢁWRꢁLQÀLFWꢁVHULRXVꢁLQMXU\ꢃ
W A R N I N G
Never direct a water stream toward people or pets, or any electrical device. Failure to heed this warning
FRXOGꢁUHVXOWꢁLQꢁVHULRXVꢁLQMXU\ꢃ
APPLICATIONS
You may use this product for the purposes listed below:
Cleaning cars, boats, motorcycles, outdoor furniture, grills, and house siding.
ADDING DETERGENT TO THE PRESSURE WASHER (See Figure 8.)
Use only detergents designed for pressure washers; household detergents, acids, alkalines, bleached,
VROYHQWVꢀꢁÀDPPDEOHꢁPDWHULDOVꢀꢁRUꢁLQGXVWULDOꢁJUDGHꢁVROXWLRQVꢁFDQꢁGDPDJHꢁWKHꢁSXPSꢃ
Many detergents may require mixing prior to use. Prepare cleaning solution as instructed on the
solution bottle.
Ŷ
Ŷ
Ŷ
Ŷ
Ŷ
Unscrew the bottle from the soap applicator.
Place the bottle on the ground or other stable surface.
Fill with pressure washer detergent.
Screw the bottle back onto the soap applicator.
Attach the soap applicator to the trigger handle
NOTE: Use a funnel, if needed, to prevent accidental spilling of the detergent outside the tank. If
DQ\ꢀGHWHUJHQWꢀLVꢀVSLOOHGꢀGXULQJꢀWKHꢀ¿OOLQJꢀSURFHVVꢁꢀPDNHꢀVXUHꢀWKHꢀXQLWꢀLVꢀFOHDQHGꢀDQGꢀGULHGꢀEHIRUHꢀ
proceeding.
Fig. 8
EN - 15
OPERATION
STARTING AND STOPPING THE PRESSURE WASHER
CAUTION :
Do not run the pump without the water supply connected and turned on.
Ŷ
Ŷ
Connect the garden hose.
Turn the garden hose on then squeeze the high pressure trigger to relieve air pressure. Once a steady
stream of water appears, release the trigger.
Ŷ
Ŷ
$IWHUꢁHQVXULQJꢁWKHꢁ2Qꢂ2IIꢁVZLWFKꢁLVꢁLQꢁWKHꢁꢇꢆꢂ2))ꢇꢁSRVLWLRQꢀꢁFRQQHFWꢁWKHꢁSUHVVXUHꢁZDVKHUꢁWRꢁWKHꢁSRZHUꢁ
supply.
Plug the pressure washer into the outlet and ensure the light on the GFCI is on, the unit is ready for
operation.
Ŷ
Ŷ
6ZLWFKꢁWKHꢁSUHVVXUHꢁZDVKHUꢁWRꢁWKHꢁꢇ,ꢂ21ꢇꢁSRVLWLRQꢁWRꢁVWDUWꢁWKHꢁPRWRUꢃ
7RꢁVWRSꢁWKHꢁPRWRUꢀꢁUHOHDVHꢁWKHꢁWULJJHUꢁDQGꢁWXUQꢁWKHꢁVZLWFKꢁWRꢁWKHꢁꢇꢆꢂ2))ꢇꢁSRVLWLRQꢃ
W A R N I N G
Hold the handle and wand securely with both hands. Expect the trigger handle to move when the trigger
LVꢁSXOOHGꢁGXHꢁWRꢁUHDFWLRQꢁIRUFHVꢃꢁ)DLOXUHꢁWRꢁGRꢁVRꢁFRXOGꢁFDXVHꢁORVVꢁRIꢁFRQWUROꢁDQGꢁLQMXU\ꢁWRꢁ\RXUVHOIꢁDQGꢁ
others.
NOTE: AUTO ON/OFF SWITCH: This Pressure washer is equipped with an Auto Start/Stop
feature.
To operate: Turn the power switch to the On (I) position. Pump will pressurize and shut down
immediately. Once the trigger of the gun is depressed the unit will turn on. Unit will shut off and
be in standby mode when trigger is released.
SOAP APPLICATION
Soap is applied under low pressure high volume for optimum performance.
Soap can not be applied under high pressure with this machine
6RDSꢁꢂꢁ'HWHUJHQWꢁFDQꢁRQO\ꢁEHꢁDSSOLHGꢁZLWKꢁWKLVꢁPDFKLQHꢁZKHQꢁWKHꢁGHWHUJHQWꢁWDQNꢁLVꢁLQVWDOOHGꢃ
EN - 16
OPERATION
USING THE SPRAY WAND TRIGGER
For greater control and safety, keep both hands on the pressure washer gun at all times.
Ŷꢁ3XOOꢁEDFNꢁDQGꢁKROGꢁWKHꢁWULJJHUꢁWRꢁRSHUDWHꢁWKHꢁSUHVVXUHꢁZDVKHUꢃ
Ŷꢁ5HOHDVHꢁWKHꢁWULJJHUꢁWRꢁVWRSꢁWKHꢁÀRZꢁRIꢁZDWHUꢁWKURXJKꢁWKHꢁVSUD\ꢁZDQGꢃ
TO ENGAGE THE LOCK-OUT (See Figure 9-1.)
Ŷ
Push up on the lock-out until it clicks into the slot. This will prevent any unintentional starts of the
pressure washer.
TO DISENGAGE THE LOCK-OUT (See Figure 9-2.)
Ŷ
Push the lock-out down and into its original position. For the most effective cleaning, the spray tip
should be between 8 in. and 24 in. from the surface to be cleaned. If the spray is too close it can
damage the cleaning surface.
Unlocked
Locked
Fig. 9-1
Fig. 9-2
W A R N I N G
Do not slide lock-out button when you have the trigger at back position.
EN - 17
OPERATION
CHANGING THE SPRAY TIP (See Figure 10.)
W A R N I N G
NEVER change spray tips without engaging the lock-out on the trigger handle and NEVER point the
ZDQGꢁDWꢁ\RXUꢁIDFHꢁRUꢁDWꢁRWKHUVꢃꢁ7KHꢁTXLFNꢄFRQQHFWꢁIHDWXUHꢁFRQWDLQVꢁVPDOOꢁVSULQJVꢁWKDWꢁFRXOGꢁHMHFWꢁWKHꢁ
VSUD\ꢁWLSꢁZLWKꢁVRPHꢁIRUFHꢃꢁ)DLOXUHꢁWRꢁKHHGꢁWKLVꢁPD\ꢁFDXVHꢁSHUVRQDOꢁLQMXU\ꢃ
Ŷ
Ŷ
Ŷ
Ŷ
Ŷ
Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure.
Engage the lock-out on the trigger handle by pushing the trigger lock button into the slot.
Pull back the quick-connect collar on the spray wand.
Push the spray tip into place in the spray wand.
Push the collar forward so that the spray tip is secured properly. Check to see that the spray tip is
secure.
Spray Tip
1-Pull back the quick-connect collar
2
2-Push the spray tip into place
3-Push the collar forward
1
3
Spray Wand
Fig. 10
APPLICATION
SPRAY TIP
Green - Narrow fan tip (25° )
Ŷ
The green pressure washer tip provides high versatility with its 25 degree angle
tip. Referred to as the washing tip, because it provides adequate pressure to
remove dirt from surfaces, but is designed to not damage many surfaces. This
pressure washer tip is designed for “sweeping” foliage or debris given its wide
angle. This tip is versatile due to its wide area of cleaning and strong pressure
application.
O
25
White - Wide fan tip (40° )
Ŷ
The white 40 degree tip, referred to as the “fan” tip creates the widest area of
cleaning with relatively low pressure. This pressure washer tip is best used for
light or delicate cleaning applications. It is recommended for light cleaning on
wood decks and other soft or delicate surfaces.
O
40
EN - 18
OPERATION
OPERATING THE PRESSURE WASHER (See Figure 11.)
Use only detergents designed for pressure washers.
Soap is applied under low pressure high volume for optimum performance.
Soap can not be applied under high pressure with this machine.
To clean:
ŶꢁInstall the soap attachment on the trigger handle.
ŶꢁStart the pressure washer and spray the detergent on a dry surface using long, even,
overlapping strokes. To prevent streaking, do not allow detergent to dry on the surface.
To rinse:
Ŷ
Using the desired tip, spray away from the rinsing surface for approximately 10 seconds to allow any
remaining detergent to be flushed from the line.
Ŷ
Start at the top of the area to be rinsed and work down, overlapping the strokes.
Fig. 11
MOVING THE PRESSURE WASHER
To move the pressure washer:
Ŷ
Turn the pressure washer off. Point the spray wand in a safe direction and pull trigger to release
water pressure.
Ŷ
Tilt the machine toward you until it balances on the wheels then roll the machine to the desired
position.
EN - 19
MAINTENANCE
W A R N I N G
When servicing, use only identical replacement parts. Use of any other parts may create a hazard or
cause product damage.
W A R N I N G
Before inspecting, cleaning or servicing the machine,turn off the unit, unplug from the outlet, pull trigger
to release water pressure and disconnect the high pressure hose. Failure to follow these instructions
FDQꢁUHVXOWꢁLQꢁVHULRXVꢁSHUVRQDOꢁLQMXU\ꢁRUꢁSURSHUW\ꢁGDPDJHꢃ
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various
types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust,
oil, grease, etc.
W A R N I N G
'RꢁQRWꢁDWꢁDQ\ꢁWLPHꢁOHWꢁEUDNHꢁÀXLGVꢀꢁJDVROLQHꢀꢁSHWUROHXPꢁEDVHGꢁSURGXFWVꢀꢁSHQHWUDWLQJꢁRLOVꢀꢁHWFꢃꢀFRPHꢁ
in contact with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in
VHULRXVꢁSHUVRQDOꢁLQMXU\ꢃ
Only the parts shown on the parts list are intended to be repaired or replaced by the customer.
All other parts should be replaced at an authorized service center.
EN - 20
MAINTENANCE
SPRAY TIP MAINTENANCE (See Figure 12.)
Excessive pump pressure (a pulsing sensation felt while squeezing the trigger) may be the result of a
clogged or dirty spray tip.
Fig. 12
Ŷ
Ŷ
Ŷ
Unplug the pressure washer.
Turn off the pressure washer and shut off the water supply. Pull trigger to release water pressure.
Remove the spray tip from the spray wand.
NOTE: Never point the spray wand at your face.
Using the spray tip cleaning tool provided, free any foreign materials clogging or restricting the spray tip
opening. Refer to Fig. 12
Ŷ
Using a garden hose, flush debris out of the spray tip by back flushing (running the water through the
spray tip backwards or from the outside to the inside).
Ŷ
Ŷ
Reconnect the spray tip to the spray wand.
Turn on the water supply.
STORING THE PRESSURE WASHER
Store in a dry, covered area where the weather can’t damage it. It is important to store this product in
a frost-free area. Always empty water from all hoses, the pump, and the detergent container before
storing.
NOTE: Use of a pump saver will give you better performance and increase the life of the machine.
EN - 21
MAINTENANCE
QUICK WINTERIZING PROCEDURE
If you cannot do the Optimum Winterizing procedure, you can still protect your pressure washer from
winter damage by doing below:
Ŷ
Ŷ
Ŷ
Ŷ
Disconnect all water connections.
Turn on the machine for a few second, until the remaining water in the pump exits. Turn off immediately.
Do not allow high-pressure hose to become kinked.
Store the machine and accessories in a room that does not reach freezing temperatures. Do not store
near furnace or other sources of heat as it may dry out the pump seals.
C A U T I O N :
Drain gun assembly of any remaining water. Aim gun downwards and squeeze trigger.
SHUTTING DOWN AND CLEANING UP
Ŷ
(If you are not using detergent, go directly to Step 2.) When you have finished using the detergent
LQMHFWLRQꢁV\VWHPꢀꢁILOOꢁGHWHUJHQWꢁERWWOHꢁZLWKꢁFOHDQꢁZDWHUꢃꢁ6LSKRQꢁZDWHUꢁDWꢁORZꢄSUHVVXUHꢁIRUꢁRQHꢁPLQXWHꢁVRꢁ
that all detergent is flushed through system. Remove detergent bottle and rinse it thoroughly.
Ŷ
Ŷ
Ŷ
Ŷ
Disconnect the garden hose from the water inlet on the unit.
Press trigger to release any remaining water pressure.
7XUQꢁWKHꢁVZLWFKꢁWRꢁꢇ2))ꢇꢁꢈꢆꢉꢁSRVLWLRQꢃ
Unplug the power cord from the outlet.
Ŷ
Engage gun safety lock.
W A R N I N G
Turn off water supply and squeeze trigger to depressurize the unit. Failure to do so could result in
SHUVRQDOꢁLQMXU\ꢁGXHꢁWRꢁGLVFKDUJHꢁRIꢁKLJKꢄSUHVVXUHꢁZDWHUꢃ
TAKING A BREAK
,IꢁWDNLQJꢁDꢁEUHDNꢁRIꢁ¿YHꢁPLQXWHVꢁRUꢁPRUHꢃ
Ŷ
Ŷ
Ŷ
Engage gun safety lock.
Turn unit to “OFF” (O) position.
Unplug the power cord from the outlet.
I M P O R T A N T :
The use of a pump protector is recommended when storing to help prevent a against freezing over the
winter months. It also help prevent the seals from drying out while sitting in storage in all climates.
EN - 22
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE SOLUTION
2Qꢂ2IIꢁVZLWFKꢁLVꢁ
in the “OFF” (O)
position.
Turn switch to the “ON” ( | ) position. Squeeze gun
trigger.
Power cord is not
plugged in.
Plug in power cord.
Extension cord is
too long.
Replace extension cord with either a 25’ (7.6 m)
14 AWG cord or a 50’ (15 m) 12 AWG cord.
Extension cord is
not proper gauge.
Motor will not start.
Extension cord is
damaged.
Electrical outlet
does not supply
adequate power.
Try a different outlet.
Tripped pressure
washer circuit
breaker.
Allow to cool, and restart unit.
Diameter of garden 5HSODFHꢁZLWKꢁDꢁꢊ´ꢁꢈꢅꢋꢁPPꢉꢁRUꢁꢋꢂꢌ´ꢁꢈꢊꢍꢁPPꢉꢁJDUGHQꢁ
hose is too small.
hose.
Water supply is
restricted.
Check garden hose for kinks, leaks and blockage.
Not enough water
supply.
Open water source fully.
Spray tip has not
been installed on
wand assembly.
Add desired pressure tip to end of wand. See page
18 Fig. 10 for details.
Unit does not reach
high pressure.
Water intake filter is
clogged.
5HPRYHꢁ¿OWHUꢁDQGꢁULQVHꢁLQꢁZDUPꢁZDWHUꢃ
&KHFNꢁWKDWꢁKRVHVꢁDQGꢁ¿WWLQJVꢁDUHꢁDLUWLJKWꢃꢁ7XUQꢁ
ꢇ2))ꢇꢁPDFKLQHꢀꢁDQGꢁSXUJHꢁSXPSꢁE\ꢁVTXHH]LQJꢁ
WULJJHUꢁJXQꢁXQWLOꢁDꢁVWHDG\ꢁÀRZꢁRIꢁZDWHUꢁHPHUJHꢁ
through the spray tip.
Pump is sucking air.
Detergent bottle
or suction tube not
properly connected.
Install detergent bottle or suction tube correctly.
Dilute detergent.
Detergent is too
thick.
EN - 23
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
Filter on detergent
suction tube is
clogged.
Run warm water through the filter to remove build
up.
Unit does not reach
Damaged or clogged
detergent suction
tube.
Remove obstruction or replace detergent suction
tube.
high pressure.
(continued)
Discharge spray tip is Blow out or remove debris with a needle or spray
obstructed.
tip cleaning tool. Refer to Fig. 12 in this manual.
Not enough inlet
water supply.
Turn water on fully. Check garden hose for kinks,
leaks or blockage.
&KHFNꢁWKDWꢁKRVHVꢁDQGꢁ¿WWLQJVꢁDUHꢁDLUWLJKWꢃꢁ7XUQꢁ
ꢇ2))ꢇꢁPDFKLQHꢀꢁDQGꢁSXUJHꢁSXPSꢁE\ꢁVTXHH]LQJꢁ
WULJJHUꢁJXQꢁXQWLOꢁDꢁVWHDG\ꢁÀRZꢁRIꢁZDWHUꢁHPHUJHꢁ
through the spray tip.
Pump is sucking air.
Output pressure varies
high and low.
Water intake filter
clogged.
5HPRYHꢁ¿OWHUꢁDQGꢁULQVHꢁLQꢁZDUPꢁZDWHUꢃ
Discharge spray tip is Blow out or remove debris with a needle or spray
obstructed. tip cleaning tool. Refer to Fig. 12in this manual.
&DOFL¿HGꢁJXQꢀꢁKRVHꢁRUꢁ Clean with distilled vinegar or a cleaner specifically
power spray tip.
made for the task.
Loose fittings.
7LJKWHQꢁ¿WWLQJVꢃ
Garden hose
connection leaks.
0LVVLQJꢂZRUQꢁUXEEHUꢁꢁ
washer.
Replace washer.
Spray wand, extension, Broken o-ring or
Call the Toll-Free Helpline.
or spray tip leaks.
plastic insert.
&KHFNꢁWKDWꢁKRVHVꢁDQGꢁ¿WWLQJVꢁDUHꢁDLUWLJKWꢃꢁ7XUQꢁ
ꢇ2))ꢇꢁPDFKLQHꢀꢁDQGꢁSXUJHꢁSXPSꢁE\ꢁVTXHH]LQJꢁ
WULJJHUꢁJXQꢁXQWLOꢁDꢁVWHDG\ꢁÀRZꢁRIꢁZDWHUꢁHPHUJHꢁ
through the spray tip.
Pump is sucking air.
Pump is noisy.
Water inlet filter
clogged.
5HPRYHꢁ¿OWHUꢁDQGꢁULQVHꢁLQꢁZDUPꢁZDWHUꢃ
Check that all fittings are tight.
Call the Toll-Free Helpline.
Loose fittings.
Water leaks from
pump.
Water seals are
damaged or worn.
Oil seals are
damaged or worn.
Oil is dripping.
Call the Toll-Free Helpline.
EN - 24
TROUBLESHOOTING
PROBLEM
POSSIBLE CAUSE
SOLUTION
Supply voltage below Verify that only the pressure washer is running on
minimum.
this circuit.
System has residual
pressure.
Turn unit “OFF”, squeeze trigger on spray wand to
release pressure, then turn unit “ON”.
Voltage loss due to
extension cord.
Unplug any extension cords attached and plug the
unit directly into the outlet.
Motor buzzes but fails
to run.
Pressure washer not
used for long periods.
Call the Toll-Free Helpline.
Residual friction
among components.
Disconnect water supply and power ON for 2 to
3 seconds, repeat couple times or until the motor
starts.
Unit might hum.
Water supply is OFF.
Turn ON water supply.
No water.
Kink in the garden
hose.
Remove kink in garden hose.
NOTE: AUTO ON/OFF SWITCH: This Pressure washer is equipped with an Auto Start/
Stop feature. To operate: Press power switch On (I). Pump will pressurize and shut
down immediately. Once the trigger of the gun is depressed the unit will turn on. Unit
will shut off and be in standby mode when trigger is released.
EN - 25
WARRANTY
GREENWORKS™ hereby warranties this product, to the original purchaser with proof of purchase, for a
period of one (1) years against defects in materials, parts or workmanship. GREENWORKS™, at its own
discretion will repair or replace any and all parts found to be defective, through normal use, free of charge
to the customer. This warranty is valid only for units which have been used for personal use that have not
EHHQꢁKLUHGꢁRUꢁUHQWHGꢁIRUꢁLQGXVWULDOꢂꢁFRPPHUFLDOꢁXVHꢀꢁDQGꢁWKDWꢁKDYHꢁEHHQꢁPDLQWDLQHGꢁLQꢁDFFRUGDQFHꢁZLWKꢁ
the instructions in the owners’ manual supplied with the product from new.
ITEMS NOT COVERED BY WARRANTY:
1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident,
improper maintenance, or alteration; or
ꢁꢁꢅꢃꢁ7KHꢁXQLWꢀꢁLIꢁLWꢁKDVꢁQRWꢁEHHQꢁRSHUDWHGꢁDQGꢂRUꢁPDLQWDLQHGꢁLQꢁDFFRUGDQFHꢁZLWKꢁWKHꢁRZQHUꢎVPDQXDOꢏꢁRU
3. Normal wear, except as noted below;
ꢁꢁꢐꢃꢁ5RXWLQHꢁPDLQWHQDQFHꢁLWHPVꢁVXFKꢁDVꢁGUDLQLQJꢁWKHꢁZDWHUꢁWRꢁDYRLGꢁIUHH]LQJꢂLFHꢁGDPDJHꢁWR
pump and components.
ꢁꢁꢋꢃꢁ1RUPDOꢁGHWHULRUDWLRQꢁRIꢁWKHꢁH[WHULRUꢁ¿QLVKꢁGXHꢁWRꢁXVHꢁRUꢁH[SRVXUHꢃ
GREENWORKS HELPLINE (1-888-90WORKS):
Warranty service is available by calling our toll-free helpline, at 1-888-909-6757 (1-888-90WORKS).
TRANSPORTATION CHARGES:
Transportation charges for the movement of any power equipment unit or attachment are the responsibility
of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted
for replacement under this warranty unless such return is requested in writing by GREENWORKS.
EN - 26
EXPLODED VIEW
EN - 27
FULL ASSEMBLIES LIST
ITEM NO.
PART NO.
321011835
321021835
33302365
321031835
321041835
32202847
332031835
321051835
341101630
3410801
DESCRIPTION
Upper housing assy
Outlet connector assy
U-clip
QTY
1
1
2
1
3
2
4
Inlet hose assy
Motor & pump assy
ST4.2*15-F Screw
Power cord assy
Switch box assy
Fan cover
1
5
1
6
14
1
7
8
1
9
1
10
11
12
13
14
15
16
17
18
19
20
21
22
23
Wire clamp
1
321081835
341231630
321061835
34211319
31240363
31225363
32903115
321071835
33201671
31103973
31111368
Lower housing assy
Gun holder
1
1
Hose reel assembly
Nozzle grommet
40 Degree nozzle
25Degree nozzle
Axle Clip
1
2
1
1
2
Wheel assy
2
Cleaning tool
1
ꢅꢋꢇꢁ+LJKꢁSUHVVXUHꢁKRVH
Soap tank
1
1
312011639
321091835
Plastic gun wand assy
Plastic gun handle assy
1
1
EN - 28
TOLL-FREE HELPLINE: 1-888-90WORKS (888.909.6757)
Rev: 00 (15-01-15)
|