FUJITSU ETERNUS LT260 User Manual
P3AM-8802-09ENZ0  
FUJITSU Storage  
ETERNUS LT260 Tape Library  
User's Guide -Panel Operation-  
Preface  
Fujitsu would like to thank you for purchasing our FUJITSU Storage ETERNUS LT260 Tape Library (hereinafter  
referred to as LT260).  
The LT260 is designed to be connected to servers (such as PRIMEQUEST, PRIMERGY, or Fujitsu M12/M10).  
This manual explains how to perform operation management and settings for the LT260 from the operator  
panel or the remote panel.  
This manual is intended for use of LT260 in regions other than Japan.  
Please carefully review the information outlined in this manual.  
Ninth Edition  
December 2019  
LTO, Linear Tape-Open, and Ultrium are registered trademarks of Hewlett Packard Enterprise, L.P., IBM Corpo-  
ration, and Quantum Corporation.  
All SPARC trademarks are used under license and are trademarks or registered trademarks of SPARC Interna-  
tional, Inc. in the United States and other countries.  
Microsoft, Windows, and Internet Explorer are either registered trademarks or trademarks of Microsoft Corpo-  
ration in the United States and/or other countries.  
The company names, product names and service names mentioned in this document are registered trade-  
marks or trademarks of their respective companies.  
Microsoft product screen shot(s) reprinted with permission from Microsoft Corporation.  
3
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
About this Manual  
Organization  
This manual is composed of the following two chapters:  
● Chapter 1 Overview  
This chapter provides an overview of the operator panel and the remote panel.  
● Chapter 2 Operating the Library  
This chapter provides information about various operations that can be performed with the operator panel  
and the remote panel.  
Warning Notations  
Warning signs are shown throughout this manual in order to prevent injury to the user and/or material dam-  
age. These signs are composed of a symbol and a message describing the recommended level of caution. The  
following explains the symbols, their levels of caution, and their meanings as used in this manual.  
This symbol indicates the possibility of serious or fatal injury if the LT260 is not  
used properly.  
WARNING  
CAUTION  
This symbol indicates the possibility of minor or moderate personal injury, as  
well as damage to the LT260 and/or to other users and their property, if the  
LT260 is not used properly.  
This symbol indicates IMPORTANT information for the user to note when using  
the LT260.  
The following symbols are used to indicate the type of warnings or cautions being described.  
Electric Shock  
The triangle emphasizes the urgency of the WARNING and CAUTION con-  
tents. Inside the triangle and above it are details concerning the symbol  
(e.g. Electrical Shock).  
No Disassembly  
The barred "Do Not..." circle warns against certain actions. The action which  
must be avoided is both illustrated inside the barred circle and written above it  
(e.g. No Disassembly).  
4
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
About this Manual  
Unplug  
The black "Must Do..." disk indicates actions that must be taken. The  
required action is both illustrated inside the black disk and written above it  
(e.g. Unplug).  
How Warnings are Presented in this Manual  
A message is written beside the symbol indicating the caution level. This message is marked with a vertical  
ribbon in the left margin, to distinguish this warning from ordinary descriptions.  
An example is shown here.  
Warning Level Indicator  
Example Warning  
Warning Type Indicator  
Warning Details  
To avoid damaging the LT260, pay attention to the following points  
when cleaning the LT260:  
- Make sure to disconnect the power when cleaning.  
- Be careful that no liquid seeps into the LT260 when using cleaners, etc.  
- Do not use alcohol or other solvents to clean the LT260.  
Warning Layout Ribbon  
Additional Information  
Symbols Used in This Manual  
The following symbols are used throughout this manual:  
This symbol alerts operators to particularly important information. Be sure to read this  
information.  
Functions and know how which can be useful when setting up or operating the LT260.  
5
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
About this Manual  
Abbreviations Used in This Manual  
• “LT260” refers to the FUJITSU Storage ETERNUS LT260 Tape Library.  
• Trademark symbols such as ™ and ® are omitted in this manual.  
6
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Table of Contents  
Chapter 1  
Overview  
12  
1.1  
Overview of Panel Operations ........................................................................................... 12  
Overview of the Operator Panel ..................................................................................................................... 12  
Overview of the Remote Panel ....................................................................................................................... 14  
1.1.1  
1.1.2  
1.2  
Operation Window ............................................................................................................ 15  
1.2.1  
Window Layout ..............................................................................................................................................15  
1.3  
Menu Layout ..................................................................................................................... 16  
Menu Layout of the Operator Panel ............................................................................................................... 16  
Menu Layout of the Remote Panel ................................................................................................................ 17  
1.3.1  
1.3.2  
Chapter 2  
Operating the Library  
18  
2.1  
2.2  
2.3  
Using the Operator Panel .................................................................................................. 19  
Using the Remote Panel ................................................................................................... 20  
Logging into the Library ................................................................................................... 21  
2.4  
Using the Library Home Screen ......................................................................................... 23  
Top Banner Elements ....................................................................................................................................24  
Left Pane Elements ........................................................................................................................................24  
Center Panel Elements .................................................................................................................................. 26  
2.4.1  
2.4.2  
2.4.3  
2.5  
Configuring the Library ..................................................................................................... 27  
Using the Initial Configuration Wizard ........................................................................................................... 27  
Saving, Restoring and Resetting the Library Configuration ............................................................................ 31  
Configuring the Date and Time Format .......................................................................................................... 34  
Configuring Media Barcode Compatibility Checking ......................................................................................38  
Configuring Allow Unlabeled Media Setting ..................................................................................................39  
Configuring License Key Handing .................................................................................................................. 40  
Configuring the RMI Timeout Setting (for Firmware Versions 7.80 and Earlier) ............................................. 41  
Configuring the Library Network Settings ......................................................................................................42  
Configuring the SNMP ....................................................................................................................................43  
Configuring the SMTP ....................................................................................................................................47  
Configuring Tape Drives ................................................................................................................................. 49  
Enabling or Disabling Mailslots ..................................................................................................................... 51  
Configuring Library Partitions ........................................................................................................................ 52  
Configuring Key Management Function ......................................................................................................... 57  
Configuring User Account Settings (for Firmware Versions 7.80 and Earlier) .................................................58  
Configuring User Account Settings (for Firmware Versions 7.90 and Later) ...................................................60  
2.5.1  
2.5.2  
2.5.3  
2.5.4  
2.5.5  
2.5.6  
2.5.7  
2.5.8  
2.5.9  
2.5.10  
2.5.11  
2.5.12  
2.5.13  
2.5.14  
2.5.15  
2.5.16  
7
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Table of Contents  
2.5.17  
2.5.18  
Configuring Password Requirements (for Firmware Versions 7.90 and Later) ................................................ 66  
Configuring the Access Management Setting to the Remote Panel ............................................................... 68  
2.6  
Maintaining the Library .................................................................................................... 82  
Library Tests ..................................................................................................................................................82  
Viewing Log Files ...........................................................................................................................................90  
Managing System Firmware .......................................................................................................................... 92  
Managing Drive Firmware ............................................................................................................................. 93  
Downloading Drive Logs ................................................................................................................................ 94  
Downloading Log and Trace Files .................................................................................................................. 96  
Rebooting the Library ....................................................................................................................................96  
Tape Drive Reboot .........................................................................................................................................97  
Controlling the UID LED ................................................................................................................................. 98  
Moving the Robotic to the Base Module ........................................................................................................98  
2.6.1  
2.6.2  
2.6.3  
2.6.4  
2.6.5  
2.6.6  
2.6.7  
2.6.8  
2.6.9  
2.6.10  
2.7  
Operating the Library ........................................................................................................ 99  
Moving Media ................................................................................................................................................99  
Opening the Mailslot ...................................................................................................................................100  
Opening a Magazine ...................................................................................................................................102  
Cleaning a Tape Drive ..................................................................................................................................103  
Rescanning the Cartridge Inventory ............................................................................................................. 104  
Forcing a Tape Drive to Eject a Cartridge ......................................................................................................105  
2.7.1  
2.7.2  
2.7.3  
2.7.4  
2.7.5  
2.7.6  
2.8  
Viewing Status Information ............................................................................................ 106  
Viewing Library and Module Status ............................................................................................................. 106  
Using Inventory Lists ...................................................................................................................................109  
Using Inventory Graphical View ................................................................................................................... 111  
Partition Map Graphical View ...................................................................................................................... 113  
Using Partition Map Configuration Status ....................................................................................................116  
Viewing Tape Drive Status ........................................................................................................................... 118  
Viewing Network Status ............................................................................................................................... 119  
Viewing Security Status ................................................................................................................................ 121  
2.8.1  
2.8.2  
2.8.3  
2.8.4  
2.8.5  
2.8.6  
2.8.7  
2.8.8  
8
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
List of Figures  
Figure 1.1  
Figure 1.2  
Figure 1.3  
Figure 1.4  
Figure 1.5  
Figure 1.6  
Figure 2.1  
Figure 2.2  
Figure 2.3  
Figure 2.4  
Figure 2.5  
Figure 2.6  
Figure 2.7  
Figure 2.8  
Figure 2.9  
Figure 2.10  
Figure 2.11  
Figure 2.12  
Figure 2.13  
Figure 2.14  
Figure 2.15  
Figure 2.16  
Figure 2.17  
Figure 2.18  
Figure 2.19  
Figure 2.20  
Figure 2.21  
Figure 2.22  
Figure 2.23  
Figure 2.24  
Figure 2.25  
Figure 2.26  
Figure 2.27  
Figure 2.28  
Figure 2.29  
Figure 2.30  
Figure 2.31  
Figure 2.32  
Figure 2.33  
Figure 2.34  
Figure 2.35  
Figure 2.36  
Figure 2.37  
Figure 2.38  
Figure 2.39  
Figure 2.40  
Figure 2.41  
Figure 2.42  
Initialization window................................................................................................................................... 13  
Login window.............................................................................................................................................. 13  
Remote panel starting window ................................................................................................................... 14  
Home screen configuration ......................................................................................................................... 15  
Menu layout of the operator panel.............................................................................................................. 16  
Menu layout of the remote panel................................................................................................................ 17  
Login........................................................................................................................................................... 21  
Home screen ............................................................................................................................................... 23  
Save/Restore configuration.......................................................................................................................... 31  
Time zone.................................................................................................................................................... 34  
Date/Time format ........................................................................................................................................ 35  
Set date/time............................................................................................................................................... 36  
SNTP............................................................................................................................................................ 37  
Media barcode compatibility check ............................................................................................................. 38  
Allow unlabeled media................................................................................................................................ 39  
License key handing.................................................................................................................................... 40  
RMI timeout ................................................................................................................................................ 41  
Network setting........................................................................................................................................... 42  
SNMP........................................................................................................................................................... 43  
SNMPv3....................................................................................................................................................... 46  
SMTP ........................................................................................................................................................... 47  
Tape drive settings ...................................................................................................................................... 49  
Enabling or disabling mailslots ................................................................................................................... 51  
Setting re-lock time..................................................................................................................................... 52  
User accounts settings................................................................................................................................. 58  
User account settings .................................................................................................................................. 60  
Adding an Account ...................................................................................................................................... 62  
Changing the Account Password.................................................................................................................. 63  
Changing the User Account Role.................................................................................................................. 64  
Deleting an account .................................................................................................................................... 65  
Password setting requirements ................................................................................................................... 67  
Access management setting to the remote panel (for firmware versions 7.80 and earlier) ........................ 68  
Access management setting to the remote panel (for firmware versions 7.90 and later) ........................... 69  
Enabling the SSL setting.............................................................................................................................. 70  
Certificate settings....................................................................................................................................... 71  
Self signed certificate creation screen ......................................................................................................... 72  
Information screen...................................................................................................................................... 73  
Certificate Signing Request screen 1............................................................................................................ 74  
Certificate Signing Request screen 2............................................................................................................ 75  
Signed Certificate screen ............................................................................................................................. 76  
Finish screen ............................................................................................................................................... 77  
Backing up the self-signed certificate.......................................................................................................... 78  
Restoring the self signed certificate ............................................................................................................ 78  
Setting the session timeout......................................................................................................................... 79  
Setting login session locking function ......................................................................................................... 79  
Disabled login session locking function....................................................................................................... 80  
Enabled login session locking function ....................................................................................................... 80  
Remote panel restriction setting ................................................................................................................. 81  
9
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
List of Figures  
Figure 2.43  
Figure 2.44  
Figure 2.45  
Figure 2.46  
Figure 2.47  
Figure 2.48  
Figure 2.49  
Figure 2.50  
Figure 2.51  
Figure 2.52  
Figure 2.53  
Figure 2.54  
Figure 2.55  
Figure 2.56  
Figure 2.57  
Figure 2.58  
Figure 2.59  
Figure 2.60  
Figure 2.61  
Figure 2.62  
Figure 2.63  
Figure 2.64  
Figure 2.65  
Figure 2.66  
Figure 2.67  
Figure 2.68  
Figure 2.69  
Figure 2.70  
Figure 2.71  
Figure 2.72  
Figure 2.73  
Figure 2.74  
Figure 2.75  
Figure 2.76  
Figure 2.77  
System test.................................................................................................................................................. 82  
Slot to slot test ............................................................................................................................................ 83  
Element to element test.............................................................................................................................. 84  
Position test ................................................................................................................................................ 86  
Wellness test ............................................................................................................................................... 88  
Robotic test ................................................................................................................................................. 89  
OCP test....................................................................................................................................................... 89  
View logs..................................................................................................................................................... 90  
Detailed view example for logs ................................................................................................................... 91  
Upgrades system firmware.......................................................................................................................... 92  
Upgrades drive firmware ............................................................................................................................. 93  
Download drive logs.................................................................................................................................... 94  
Download logs and traces ........................................................................................................................... 96  
Rebooting the library .................................................................................................................................. 96  
Tape drive reboot ........................................................................................................................................ 97  
UID LED control ........................................................................................................................................... 98  
Move robotic to base module ...................................................................................................................... 98  
Move media ................................................................................................................................................ 99  
Open mailslot............................................................................................................................................ 101  
Open magazine......................................................................................................................................... 102  
Clean drive ................................................................................................................................................ 103  
Rescan inventory....................................................................................................................................... 104  
Force drive media eject ............................................................................................................................. 105  
Library status............................................................................................................................................. 106  
Inventory list ............................................................................................................................................. 109  
Inventory graphical view ........................................................................................................................... 111  
Inventory graphical view (display status).................................................................................................. 112  
Inventory graphical view (display error status).......................................................................................... 113  
Partition map graphical view..................................................................................................................... 113  
Partition map graphical view (display partition information) ................................................................... 114  
Partition map graphical view (tape drive information display) ................................................................. 115  
Using partition map configuration status.................................................................................................. 116  
Tape drive status ....................................................................................................................................... 118  
Network status .......................................................................................................................................... 119  
Viewing security status.............................................................................................................................. 121  
10  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
List of Tables  
Table 2.1  
Table 2.2  
Table 2.3  
Status icons ................................................................................................................................................. 18  
Front panel LED indicators .......................................................................................................................... 19  
Management software ................................................................................................................................ 43  
11  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 1  
Overview  
This chapter provides an overview of the operator panel and the remote panel.  
1.1  
Overview of Panel Operations  
The library provides two main interfaces:  
• Operator panel  
With the operator panel, you can monitor, configure, and control the library from the front panel. All oper-  
ating menus are displayed on the center pane.  
• Remote panel  
With the remote panel, you can monitor, configure, and control the library from a web browser. The remote  
panel hosts a dedicated, protected Internet site that displays a graphical representation of the library.  
Except of top menus, operating menu tree are displayed on the right pane.  
Although the operator panel is similar to the remote panel in design and functionality, some of the execut-  
able operations are different.  
1.1.1  
Overview of the Operator Panel  
The operator panel is positioned on the center of the front panel. It is possible to perform operations such as  
referencing/setting the library and drive status and opening the magazine or mailslot from the operator  
panel. By selecting the buttons on the operator panel, operations such as window transition, function selec-  
tion, and setup value input can be performed.  
The windows on the operator panel before login can be roughly divided into the initialization window and  
login window.  
12  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
       
Chapter 1 Overview  
1.1 Overview of Panel Operations  
■ Initialization window  
Initialization is started when the library is turned on. In the initialization window, the progress status of the  
library initializing are displayed.  
Figure 1.1 Initialization window  
■ Login window  
When initialization operation ends, the login window is displayed on the operator panel.  
If the screen saver is on, please tap the screen.  
Figure 1.2 Login window  
13  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 1 Overview  
1.1 Overview of Panel Operations  
1.1.2  
Overview of the Remote Panel  
The remote panel can be used to perform operations such as referencing/setting the library and drive status  
and performing drive cleaning on a Web browser via the LAN.  
• The recommended environment for the remote panel is as follows:  
- Web browser  
Microsoft Internet Explorer, Mozilla Firefox, Google Chrome, Safari  
• Cookies and Java Script are used for the remote panel. Cookies and Java Script need to be enabled in your  
browser.  
Before using the remote panel, network settings need to be performed on the operator panel to enable the IP  
address, the subnet mask, and the gateway so that the remote panel can be used. Specify the following URL  
on a Web browser after performing the settings:  
http:// <IP address specified for the LT260>/  
or  
https:// <IP address specified for the LT260>/  
Use the https URL to connect to the remote panel for the LT260 when SSL is enabled. For details related to  
enabling SSL, refer to "2.5.18 Configuring the Access Management Setting to the Remote Panel" (page 68).  
The following window is displayed when the LT260 is connected.  
Figure 1.3 Remote panel starting window  
14  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 1 Overview  
1.2 Operation Window  
1.2  
Operation Window  
1.2.1  
Window Layout  
The home screen window is displayed after login. See "2.4 Using the Library Home Screen" (page 23) for  
details.  
The library home screen is organized into the following regions:  
● Top banner  
Contains the home button and displays the overall status and information about the library and user.  
● Left pane  
Displays the library identity and module status.  
● Center pane  
Provides access to operate and configure the library and to view additional status information.  
● Right pane (remote panel only)  
Displays a log of recent events.  
Figure 1.4 Home screen configuration  
Top banner  
Right pane  
Left pane  
Center pane  
15  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 1 Overview  
1.3 Menu Layout  
1.3  
Menu Layout  
This section describes the menu layout of the operator panel and the remote panel.  
1.3.1  
Menu Layout of the Operator Panel  
The menu layout of the operator panel is as follows.  
Figure 1.5 Menu layout of the operator panel  
Login  
Home  
Open Mailslot  
Open Magazine  
Configuration  
Configuration Wizard  
System  
Maintenance  
Library Test  
View Log  
Operation  
Move Media  
Open Mailslot  
Status  
Library Status  
Cartridge Inventory  
Network  
Drives  
Software Upgrades  
Download Logs  
Open Magazine  
Clean Drive  
Partition Map  
Drive Status  
Mailslot  
System Reboot  
UID LED Control  
Rescan  
Network Status  
Security  
Force Drive Media Eject  
Unlock Multiple Magazine  
Local User Accounts  
Web Management  
Move Robotic to Base Module  
Although the Open Mailslot menu and the Open Magazine menu are in both the Home menu and the Operation menu, they are the same functions.  
Menus that have been added or changed for firmware versions 7.90 and later.  
16  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
       
Chapter 1 Overview  
1.3 Menu Layout  
1.3.2  
Menu Layout of the Remote Panel  
The menu layout of the remote panel is as follows.  
Figure 1.6 Menu layout of the remote panel  
Login  
Home  
Configuration  
Initial Configuration Wizard  
System  
Maintenance  
Library Test  
Operation  
Move Media  
Open Mailslot  
Status  
Open Mailslot  
Open Magazine  
Library Status  
Logs and Traces  
Cartridge Inventory  
Network  
Software Upgrades  
Open Magazine  
Clean Drive  
Partition Map  
Drive Status  
Network Management  
Download Drive Logs  
Drives  
System Reboot  
Drive Reboot  
Rescan Inventory  
Network Status  
Security  
Mailslot  
Force Drive Media Eject  
Partition  
UID LED Control  
Encryption  
Move Robotic to Base Module  
User Accounts  
Web Management  
Although the Open Mailslot menu and the Open Magazine menu are in both the Home menu and the Operation menu, they are the same functions.  
Menus that have been added or changed for firmware versions 7.90 and later.  
17  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2  
Operating the Library  
The library provides two main interfaces:  
• Operator panel  
With the operator panel, you can monitor, configure, and control the library from the front panel. All oper-  
ating menus are displayed on the center pane.  
• Remote panel  
With the remote panel, you can monitor, configure, and control the library from a web browser. The remote  
panel hosts a dedicated, protected Internet site that displays a graphical representation of the library.  
Except of top menus, operating menu tree are displayed on the right pane.  
Although the operator panel is similar to the remote panel in design and functionality, some of the execut-  
able operations are different.  
Table 2.1 shows the status icons that appear on the panels and the meaning of the icons.  
Table 2.1 Status icons  
LED  
Function  
The green Status OK icon indicates that the library is fully operational and that no user interaction is  
required.  
The yellow exclamation point Status Warning icon indicates that user attention is necessary, but  
that the device can still perform most operations.  
The red X Status Error icon indicates that user intervention is required and that the device is not  
capable of performing some operations.  
18  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.1 Using the Operator Panel  
2.1  
Using the Operator Panel  
The front panel has a power button, an LCD touch screen, and five LEDs. With the operator panel you can  
monitor, configure, and operate most library functions from the front panel. To navigate the operator panel,  
tap on the LCD touch screen.  
Table 2.2 Front panel LED indicators  
LED  
Function  
Blue when activated. The unit identification (UID) LEDs are controlled by the user through the operator  
panel and remote panel Maintenance > UID LED Control screen. The UIDs on the operator panel and back  
panel UID are activated and deactivated together. The UIDs are helpful for locating the library in a data  
center.  
Module ID  
Ready  
Clean  
Green, steady when power is on, blinking with tape Ready drive or library robotic activity.  
Amber when a tape drive cleaning operation is recommended.  
Amber if the library has detected a condition for which user attention is necessary, but that the library can  
still perform most operations.  
Attention  
Error  
Amber if an unrecoverable tape drive or library error occurs. A corresponding error message is displayed  
on the LCD screen. User intervention is required; the library is not capable of performing some operations.  
The operator panel screen may be initialized if time elapses without logging in or during the logout process.  
As a feature, the operator panel turns white for a few seconds during the initialization of the screen and then  
login screen appears.  
19  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.2 Using the Remote Panel  
2.2  
Using the Remote Panel  
With the remote panel, you can monitor, configure, and operate most library functions from a web browser.  
When possible, it is recommended that the remote panel be used as the primary library interface because  
compared to the operations of the operator panel, the web interface provides access to additional features,  
such as online help, and is easier to use. However, the remote panel is not required to use the product, except  
to configure advanced features, such as SNMP, IPv6, encryption, and partitions.  
Before using the remote panel, you must configure the library network settings and set the administrator  
password with the operator panel. This can be done with the Initial Configuration Wizard. See "2.5.1 Using the  
Initial Configuration Wizard" (page 27).  
To start the remote panel, open the latest version of a supported web browser and enter the IP address of the  
library in the browser’s address bar. Supported browsers include Internet Explorer (version 10 or later is rec-  
ommended), Firefox, Chrome and Safari.  
Check the online help in the remote panel for additional information. The help pages are updated with firm-  
ware updates and often contain up-to-date technical details that might not be contained in this document.  
To access remote panel help, click the  
icon on the right side of the remote panel top banner.  
20  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.3 Logging into the Library  
2.3  
Logging into the Library  
Figure 2.1 Login  
Procedure  
1
Operator panel: If the operator panel screen saver is on, tap the screen.  
Remote panel: Open a supported web browser and enter the IP address of the library in the  
browser’s address bar.  
2
3
4
Select the User.  
If required, enter the Password.  
Click Login.  
End of procedure  
The user levels are:  
• user  
The initial password is "std00001". The user account provides access to status information, but not  
configuration, maintenance or operation functions. The administrator account can be used to set the user  
account password, and allow or forbid the use of some of the operation functions by the user account.  
Based on the firmware version, refer to "2.5.15 Configuring User Account Settings (for Firmware Versions  
7.80 and Earlier)" (page 58), or "2.5.16 Configuring User Account Settings (for Firmware Versions 7.90 and  
Later)" (page 60) for details.  
• administrator  
The administrator password is required to login as the administrator user. The same administrator pass-  
word is used for the remote panel and operator panel. The initial administrator password is "adm00001".  
The administrator user has access to all functionality except for the log configuration and Service features.  
21  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.3 Logging into the Library  
From a security perspective, changing the default password immediately after starting the library is recom-  
mended.  
When logging in for the first time, change the password using the Initial Configuration Wizard or change the  
password with the user account settings.  
Refer to "2.5.1 Using the Initial Configuration Wizard" (page 27), "2.5.15 Configuring User Account Settings  
(for Firmware Versions 7.80 and Earlier)" (page 58), or "2.5.16 Configuring User Account Settings (for  
Firmware Versions 7.90 and Later)" (page 60) for details.  
• service  
Access to this user is by Service personnel only. The service password is set at the factory. The same service  
password is used for the remote panel and operator panel. Both the administrator and service passwords  
are required for a service person to enter the service area.  
• security  
In addition to the functions that are available when logged in as the administrative user, the key  
management function can be set. After the Key Management Function Option is purchased, the setting for  
the key management function is available.  
The initial password is "security". However, this password can only be used to log in from the operator  
panel.  
After the initial password is changed on the operator panel, the password can then also be used to log in  
from the remote panel.  
Basically, only one user can log in to the library regardless of whether the user logs in from the remote panel  
or operator panel.  
If a user is currently logged in, a warning message appears. Select whether to continue the login process.  
• Select Leave to stop the login process.  
• Select Login to continue the login process and forcibly log the currently logged in user out.  
As an exception, only the "user" user account can log in to the library regardless of whether other users are  
logged in.  
Note that if no operation is performed for a certain period of time, the user is forcibly logged out.  
22  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.4 Using the Library Home Screen  
2.4  
Using the Library Home Screen  
The library home screen is organized into the following regions:  
• Top banner  
Contains the home button and displays the overall status and information about the library and user.  
• Left pane  
Displays the library identity and module status.  
• Center pane  
Provides access to operate and configure the library and to view additional status information.  
• Right pane (remote panel only)  
Displays a log of recent events.  
Figure 2.2 Home screen  
Top banner  
Right pane  
Left pane  
Center pane  
23  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.4 Using the Library Home Screen  
2.4.1  
Top Banner Elements  
•
(Home Icon)  
Returns to the library home screen.  
• Library Health  
An icon indicating the overall health status of the library  
-
The green check mark Status OK icon indicates that all library components are fully operational and  
that no user intervention is required.  
-
The yellow triangle exclamation point Status Warning icon indicates that user attention is necessary,  
but that the library can still perform most operations. Click the icon to display the event ticket log.  
-
The red circle X Status Error icon indicates that user intervention is required and the library is not  
capable of performing some operations. Click the icon to display the event ticket log.  
• Status  
The status of the library robotic  
- Idle  
The library robotic is ready to perform an action.  
- Moving  
The library robotic is moving a cartridge.  
- Scanning  
The library robotic is performing an inventory of cartridges.  
- Offline  
The robotic assembly is being used by the library or is disabled.  
• Library Time & Date  
Helpful when analyzing event logs and support tickets, and might be needed when contacting support.  
• User  
The user account for this session  
• Logout  
Logs out of this session.  
•
Accesses online help.  
2.4.2  
Left Pane Elements  
• Library Status  
Overall library confirmation and status  
- Serial #  
The base module serial number  
- Hostname  
The library hostname  
24  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.4 Using the Library Home Screen  
- Network Configuration  
The IP version (IPv4 or IPv6) and IP address  
- Firmware  
The library firmware version  
• Module Status Overviews  
A summary of each module’s configuration and health. Click or tap the module status area to select the  
module.  
- Module Health Icon  
•
The green check mark Status OK icon indicates that the module and each of its components are fully  
operational and that no user intervention is required.  
•
The yellow triangle explanation point Status Warning icon indicates that user attention is neces-  
sary, but that the library can still perform most operations.  
•
The red circle X Status Error icon indicates that user intervention is required and the module is not  
capable of performing some operations.  
- Module Number  
Modules are numbered based on their location in the physical library. The bottom module is Module 1.  
The base module is annotated with (Base).  
- Tape Drive Status  
The number of tape drives installed in the module and the health of each tape drive. Click or tap on the  
tape drive to display the tape drive configuration and status information in the center pane.  
• A black square indicates that the tape drive is fully operational and that no user intervention is  
required.  
• A yellow square indicates that user attention is necessary, but that the tape drive can still perform  
most operations.  
• A red square indicates that user intervention is required or the tape drive is not capable of perform-  
ing some operations.  
- Magazine Slot Usage  
The number of cartridge slots available and the number in use.  
- Tape Drive Operation Status  
The current tape drive activity for each tape drive in the module. The tape drive operation status is only  
displayed for the selected module.  
• Write  
The tape drive is performing a write operation.  
• Read  
The tape drive is performing a read operation.  
• Idle  
A cartridge is in the tape drive but the tape drive is not performing an operation.  
• Empty  
The tape drive is empty.  
• Encrypt  
The tape drive is writing encrypted data.  
25  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.4 Using the Library Home Screen  
2.4.3  
Center Panel Elements  
• Open Mailslot (Non-user account)  
Click or tap to unlock the mailslot on the selected module. Mailslots must be enabled before the slots can  
be used as mailslots. See "2.5.12 Enabling or Disabling Mailslots" (page 51).  
• Open Magazine (Non-user account)  
Click or tap to unlock a magazine in the selected module. Only one magazine in the library can be open at  
a time. See "2.7.3 Opening a Magazine" (page 102).  
• Configuration (Non-user account)  
Click or tap to configure the library. See "2.5 Configuring the Library" (page 27).  
• Maintenance (Non-user account)  
Click or tap to access maintenance functions. See "2.6 Maintaining the Library" (page 82).  
• Operation (Non-user account)  
Click or tap to access operation functions. See "2.7 Operating the Library" (page 99).  
• Status  
Click or tap to access status information. See "2.8 Viewing Status Information" (page 106).  
26  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5  
Configuring the Library  
Click or tap [Configuration] in the home screen to access the library configuration function. From the list dis-  
played in the center pane in the operator panel or the right pane in the remote panel, select the item to con-  
figure. Refer to "1.3 Menu Layout" (page 16) for the items.  
For items with a sub-menu, click or tap the item to expand the sub-menu.  
2.5.1  
Using the Initial Configuration Wizard  
The wizard guides you through setting the administrator password, configuring the time zone, date and time,  
and library network settings. When logging in to the remote panel for the first time, performing a configura-  
tion using this function is recommended.  
The items that can be configure by this function can also be configured individually. To configure an item  
individually, refer to the following as required.  
• Administrator password  
"2.5.15 Configuring User Account Settings (for Firmware Versions 7.80 and Earlier)" (page 58) or "2.5.16  
Configuring User Account Settings (for Firmware Versions 7.90 and Later)" (page 60)  
• Timezone  
"2.5.3.1 Setting the Time Zone" (page 34)  
• Date and time  
"2.5.3.2 Setting the Date and Time Format" (page 35)  
• Library network settings  
"2.5.8 Configuring the Library Network Settings" (page 42)  
27  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
To configure the library, perform the following procedure.  
Procedure  
1
2
In the [Configuration > System] screen, click "Initial Configuration Wizard" in the right pane  
to start the wizard.  
Click [Next].  
To skip the configuration, click [Next] without entering any information. To go back to the previous  
item, click [Back]. To cancel the configuration, click [Cancel].  
3
Set the administrator password.  
Enter the password twice and click [Submit]. When the setting is completed, click [Next].  
28  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
4
Configure the network settings.  
Enter a value for the required items and then click [Next].  
Enter values according to the selected [Protocol].  
When directly entering an Internet address, select Static for [Method] and enter a value in each item.  
When automatically obtaining an Internet address from a DHCP server, select DHCP (for IPv4) or State-  
less (for IPv6).  
5
Configure the timezone  
Select a timezone location from [Timezone Lists]. For location names that start with ">", a  
sub-menu is displayed in the right pane when selected and a more detailed location can be  
selected. After selecting a timezone, click [Next].  
For example, select [Asia > Tokyo] to set the timezone to Japan Standard Time.  
29  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
6
Configure the date and time.  
Select a time format for [Time Format] and a date format for [Date Format], enter the date  
and time, and then click [Next].  
By pressing the [Now] button, the date and time are synchronized with the PC and automatically  
entered.  
7
8
Click [Finish].  
Confirm the result of the configuration and click [OK] to complete the configuration.  
End of procedure  
30  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.2  
Saving, Restoring and Resetting the Library Configuration  
From the Configuration > System > Save/Restore Configuration screen you can save the library configuration  
settings to a file, restore the settings, or reset the library configuration. The saved configuration database will  
make it easier it recover the library configuration if you need to replace the base module or base module con-  
troller.  
When the library is configured or set after purchasing the LT260 or when the library configuration or setting  
is changed during operation, make sure to save the library configuration settings as a file. The saved library  
configuration setting file can be restored in the library using the remote panel. Keep the latest library config-  
uration setting file in a safe location. This file may be required for maintenance.  
Figure 2.3 Save/Restore configuration  
31  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
■ Saving the library configuration to a file  
Procedure  
1
Navigate to the Configuration > System > Save/Restore Configuration screen as shown  
above.  
2
3
Under Save Configuration File, click Save.  
When Download appears, click it and then select the destination location.  
End of procedure  
■ Restoring the library configuration from a file  
If the Key Management Function Option is being used, the master key and the encryption key are deleted  
when the device setting information is restored.  
Because encrypted data will become unreadable if the master key and the encryption key are deleted, ask  
the security administrator to export the master key and the encryption key in advance and store them in a  
secure location.  
Refer to "2.2 Backing Up the Setting Information" of "FUJITSU Storage ETERNUS LT260 Tape Library Key Man-  
agement Function Option User's Guide" for details.  
Procedure  
1
2
Navigate to the Configuration > System > Save/Restore Configuration screen.  
Under Restore Configuration File, click Browse. Then select the location of the configuration  
file.  
3
Click Upload File & Restore.  
If the library configuration is restored, the library is restarted.  
End of procedure  
32  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
■ Resetting the library configuration information  
To reset the library configuration information to the default settings, click Reset Default Settings and select  
Yes.  
If the library configuration information is reset, the library is restarted.  
■ Resetting the list of known drives and modules  
To reset the list of known drives and modules, click Reset the List of Known Drives and Modules and select Yes.  
Resetting the list of known drives and modules will cause the library to re-discover only the drives and  
modules that are physically present. This operation will alter the list of element addresses reported to hosts  
and will re-number the drives and modules. This operation cannot be undone. After the operation  
completes, use one of the partition wizards to modify partitioning as needed.  
■ Resetting hardware configuration  
To reset the hardware configuration, click Reset Hardware Configuration and select Yes.  
Resetting the Hardware Configuration will cause the library to re-discover the currently present hardware.  
This operation cannot be undone. After the operation completes, use one of the partition wizards to modify  
partitioning as needed.  
33  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.3  
Configuring the Date and Time Format  
To configure date and time format parameters and to use an SNTP server, from the Configuration area, navi-  
gate to the System > Date and Time Format screen.  
The library does not adjust its time for daylight saving time; the time must be adjusted manually.  
2.5.3.1  
Setting the Time Zone  
Procedure  
1
Click Time Zone.  
A list of continents, countries, and regions is displayed. When an item proceeded with ">", for example  
"> US", is selected, a submenu is displayed in the next column.  
Figure 2.4 Time zone  
2
3
Expand the time zone list, as necessary, until a location with the appropriate time zone is  
visible. Select a location with the appropriate time zone.  
For example, select [Asia > Tokyo] to set the timezone to Japan Standard Time.  
Click Submit.  
End of procedure  
34  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.3.2  
Setting the Date and Time Format  
Procedure  
1
Click Date/Time Format.  
Figure 2.5 Date/Time format  
2
3
Select a time format.  
Select a date format:  
For example, July 30, 2013 is displayed as:  
• DD.MM.YYYY - 30.07.2013  
• MM/DD/YYYY - 07/30/2013  
• YYYY-MM-DD - 2013-07-30  
4
Click Submit.  
End of procedure  
35  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.3.3  
Setting the Date and Time  
Procedure  
1
Click Set Date/Time.  
Figure 2.6 Set date/time  
2
3
Enter time and date information.  
Manual Input:  
Enter time and date information directly.  
Automatic Input:  
Click Now. The time and date information is entered automatically by the synchronization to the  
computer running the remote panel.  
Click Submit.  
End of procedure  
36  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.3.4  
Enabling SNTP (Simple Network Time Protocol) Synchronization  
The library must have network access to an SNTP server.  
Procedure  
1
Click SNTP.  
Figure 2.7 SNTP  
2
3
4
Click SNTP Enabled.  
Enter the SNTP server address.  
Click Submit.  
End of procedure  
Synchronization to the SNTP server is executed every 8 hours. Depending on the time deviation, the synchro-  
nization mode (Step mode/Slew mode) is automatically selected.  
37  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.4  
Configuring Media Barcode Compatibility Checking  
From the Configuration > System > Media Barcode Compatibility Check screen you can enable or disable the  
barcode media ID check.  
Figure 2.8 Media barcode compatibility check  
When Barcode Media ID Restriction is enabled, the library will only allow appropriate tape cartridges to be  
loaded into tape drives. The barcode media ID is the last two characters of the barcode. For example, an LTO-  
6 labeled cartridge will not be allowed to move into an LTO-5 tape drive.  
When disabled, the library will move any tape to any tape drive. If the cartridge is incompatible with the tape  
drive, the library will display a message.  
• It is strongly recommended that all cartridges have barcode labels with the correct media ID, and that the  
Barcode Media ID Restriction is enabled.  
• If a barcode label with an incorrect media ID is being used, the tape cartridge may be moved to an incom-  
patible tape drive.  
38  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.5  
Configuring Allow Unlabeled Media Setting  
Although it is strongly recommended to use labeled media, the tape library is capable to detect cartridges  
without barcode label within the inventory scan. This function enables the library to detect and use cartridges  
unlabeled or difficult to read labels.  
To enable detection of cartridges unlabeled or difficult to read labels navigate to Configuration > System >  
Allow Unlabeled Media.  
Procedure  
1
2
Set the checkbox.  
Click Submit.  
Figure 2.9 Allow unlabeled media  
End of procedure  
Using this option may increase the duration of the inventory time, thus it is strongly recommended to use  
correctly labeled media!  
39  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.6  
Configuring License Key Handing  
When adding a license key, navigate to the System > License Key Handling screen.  
Figure 2.10 License key handing  
Procedure  
1
2
Enter license key.  
The license key needs to have a length of 15 characters.  
Click Add License.  
End of procedure  
40  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.7  
Configuring the RMI Timeout Setting (for Firmware Versions 7.80 and Earlier)  
To set the timeout for the remote panel, navigate to the System > RMI Timeout screen.  
Procedure  
1
2
Select timeout value (5 or 30 minutes).  
Click Submit.  
Figure 2.11 RMI timeout  
End of procedure  
For firmware versions 7.90 and later, this setting has been integrated in the [Configuration > Web Manage-  
ment] menu.  
To set the remote panel timeout for firmware versions 7.90 and later, refer to "2.5.18.5 Setting the Session  
Timeout Period of the Remote Panel (for Firmware Versions 7.90 and Later)" (page 79).  
41  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.8  
Configuring the Library Network Settings  
From the Configuration > Network screen you can configure the library network settings.  
Figure 2.12 Network setting  
Procedure  
1
2
Navigate to the Configuration > Network screen.  
Configure or update the Host Name and Domain Name. The remote panel URL is <Host  
Name>.<Domain Name>.  
3
4
Select the Internet protocol to use for the library.  
Configure the settings for the selected Internet protocol.  
To have the library obtain an Internet address from a DHCP server, select the DHCP or Stateless method.  
5
Click Submit.  
End of procedure  
Use "Reset internal IP Range" in case that the network conflict is occurred. This function should not be used in  
other case.  
Refer to "User's Guide -Installation & Operation- 3.1 Powering On/Off" about how to use the function.  
42  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.9  
Configuring the SNMP  
This operation can be executed from only remote panel operation.  
Use the Configuration > Network Management screen to enable and configure SNMP (Simple Network  
Management Protocol), which allows applications to manage the device. The library supports both SNMP  
configuration and SNMP traps.  
The monitoring server can receive SNMP traps if the "ETERNUS SF Storage Cruiser" management software is set  
up on the server. Refer to the ETERNUS SF Storage Cruiser manuals for details.  
Table 2.3 Management software  
Software name  
Supported function  
FUJITSU Storage ETERNUS SF Storage Cruiser  
SAN management, fault monitoring  
For information about the versions of ETERNUS SF Storage Cruiser that support the LT260, contact our sales  
representative.  
Figure 2.13 SNMP  
43  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.5 Configuring the Library  
• SNMP Enabled  
When checked, the library can be managed by computers listed in the SNMP Target IP Addresses field.  
• Community Name  
A string used to match the SNMP management station and library. It must be set to the same name on  
both the management station and the library. The default community name is public.  
• Notification Level  
The types of events for which the library should send.  
- Inactive  
No events are sent.  
- Critical  
Only critical events are sent.  
- + Warnings  
Only critical and warning events are sent.  
- + Configuration  
Only critical, warning, and configuration events are sent.  
- + Information  
All events are sent.  
• SNMP Targets  
List of configured SNMP targets.  
The following are the optional settings for SNMPv3. When using SNMPv3, perform these settings.  
• Limit all library SNMP communication to SNMPv3  
If the checkbox is selected, the usable SNMP version is limited to SNMPv3. If this setting is enabled, the  
SNMP Targets set with SNMPv1 and SNMPv2 are deleted. When the checkbox is selected, a confirmation  
screen is displayed. Click [Yes] to proceed.  
• SNMPv3 Security Level  
SNMPv3 security level for SNMP communication  
- noAuthNoPriv  
Authentication and encryption are not used for SNMP communication.  
- AuthNoPriv  
Authentication is used for SNMP communication.  
- AuthPriv  
Authentication and encryption are used for SNMP communication.  
• Authentication User Name  
The username used for communication using SNMPv3. Required when using SNMPv3.  
• Authentication Password  
A password with eight or more characters used for SNMP communication authentication. Required when  
AuthNoPriv and AuthPriv are selected for SNMPv3 Security Level.  
44  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
■ To add an SNMP target or edit information for an SNMP target  
Procedure  
1
Click Edit for the appropriate SNMP target. When adding an SNMP target, click Edit next to a  
target without an IP/Hostname.  
2
3
4
5
6
7
Enter the target IP address or hostname.  
Enter the port.  
Select the SNMP version.  
Enter the SNMP community string for the target.  
Enter the optional setting for SNMPv3. (When using SNMPv3)  
Click Submit.  
End of procedure  
■ To delete an SNMP target  
Procedure  
1
2
Click Delete for the target to be deleted.  
Click Submit.  
End of procedure  
45  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
■ To clear SNMPv3 Options  
Procedure  
1
Click Clear SNMPv3 Options.  
To confirm that you want to clear the SNMPv3 Options, click Yes.  
Figure 2.14 SNMPv3  
2
Click the [Yes] button.  
End of procedure  
46  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.10 Configuring the SMTP  
This operation can be executed from only remote panel operation.  
From the Configuration > Network Management > SMTP screen you can enable SMTP (Simple Mail Transfer  
Protocol) functionality and configure E-mail notification of library events. The library must have network  
access to an SMTP server.  
Figure 2.15 SMTP  
• SMTP Enabled  
Check to enable SMTP. When checked, the remaining configurations are active.  
• Notification Level  
The types of events for which the library should send E-mail  
- Inactive  
No events are sent.  
- Critical  
Only critical events are sent.  
- + Warnings  
Only critical and warning events are sent.  
- + Configuration  
Only critical, warning, and configuration events are sent.  
- + Information  
All events are sent.  
• SMTP Server  
Hostname or IP address of the SMTP server  
47  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
• Security  
Security protocol for accessing the SMTP server  
- None  
- SSL  
- TLS  
• SMTP Port  
SMTP server port. The default port for the selected protocol will be selected. You can choose one of the  
default ports or configure a custom port.  
• To Email Address  
The address to receive the reported events (for example [email protected]). Only one  
email address can be configured.  
• Mailer Name  
Name of the sender of the E-mail  
• Email Subject  
Subject line for the E-mail message  
• Emailer Address  
Return address to use for the E-mail message  
• Authentication Required  
When checked, a username and password are required to access the SMTP server.  
• Username  
User account for logging into the SMTP server when authentication is required.  
• Password  
Password associated with the Username when authentication is required.  
48  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.11 Configuring Tape Drives  
From the Configuration > Drives screen you can see and modify the tape drive configuration.  
Figure 2.16 Tape drive settings  
• Tape drive number  
Tape drives are numbered from the bottom of the library up beginning with one. The tape drive currently  
hosting the SCSI communication for the library is designated with (LUN).  
• Serial number  
The serial number assigned to the tape drive by the library. This serial number is reported to host applica-  
tions. The serial number cannot be modified.  
This is not the serial number assigned to the tape drive by the manufacturer; the serial number assigned  
by the manufacturer is shown in Manufacturer S/N.  
• LTO generation  
- LTO 5  
Ultrium 3000, Ultrium 3280  
- LTO 6  
Ultrium Tape Drive, Ultrium 6250  
- LTO 7  
Ultrium Tape Drive  
- LTO 8  
Ultrium Tape Drive  
49  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
• Tape drive form factor  
- HH  
Half height  
• Tape drive interface  
- FC  
Fibre Channel  
- SAS  
Serial Attached SCSI  
• (Modified)  
When present indicates that a setting has been changed. To apply the changes, click Submit. To reset all  
changed fields to their previously saved values, click Undo.  
• Pwr  
Indicates whether the tape drive is currently powered on or off.  
• Firmware  
The version of firmware currently installed on the tape drive.  
• Manufacturer S/N  
The serial number assigned to the tape drive when it was manufactured. Use this serial number when  
working with your Service.  
• Power On  
Checked when the tape drive is powered on.  
Always power off a tape drive before removing it from the library or moving it to a new location within the  
library.  
• Port X configuration (FC only)  
Tape drive port configuration.  
- Speed  
The currently selected speed. The default is Automatic.  
- Port Type  
• Automatic  
• Loop  
Enables selection of the Addressing Mode.  
• Fabric  
- Addressing Mode  
When Port Type is set to Loop, Addressing Mode can be set to Soft, Hard, or Hard Autoselect.  
- Loop ID/ALPA  
When Addressing Mode is set to Hard, you can choose an ALPA address from the drop down list.  
50  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
■ To modify the configuration of one or more tape drives  
Procedure  
1
2
Modify any of the configurable values.  
Click Submit.  
End of procedure  
To configure the number of barcode characters to report to the host application and whether to report them  
from the left or right end of the label, use either the Basic Partition Wizard or Expert Partition Wizard. See  
"2.5.13.1 Using the Basic Partition Wizard" (page 53) or "2.5.13.2 Using the Expert Partition Wizard" (page  
55).  
2.5.12 Enabling or Disabling Mailslots  
The Configuration > Mailslot screen lists each of the mailslots and shows whether each is enabled or disabled.  
To change the state, click the button for the mailslot and then click Submit. Slots not enabled as mailslots are  
available as storage slots.  
Figure 2.17 Enabling or disabling mailslots  
Do not change the mailslot setting (enable or disable) while the backup software is in use. If a change is  
required, stop the backup software before performing any changes.  
51  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
The mailslot and magazine automatic re-lock duration can be selected.  
Procedure  
1
2
Selection duration: 30 seconds (default) or 5 minutes.  
Click Submit.  
Figure 2.18 Setting re-lock time  
End of procedure  
2.5.13 Configuring Library Partitions  
This operation can be executed from only remote panel operation.  
The library has a flexible partitioning scheme with a few key constraints:  
• The license option is necessary to create more than 2 partitions.  
• Each partition must have at least one tape drive. One tape drive in each partition will host the library LUN  
for the partition.  
• The maximum number of partitions is 20.  
• Magazine slots are allocated in five-slot groups.  
• Mailslots must be enabled for a module before they can be allocated to a partition.  
A partition does not need to have a mailslot. If a partition does not have a mailslot, the magazine must be  
accessed to import or export cartridges. Opening a magazine takes the library off line.  
Although the mailslot magazine is shared between partitions, the mailslot elements are assigned individ-  
ually to partitions.  
52  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
Wizards guide you through the partition configuration process. The wizards are only accessible from the  
remote panel.  
• Basic Partition Wizard  
You specify the number of partitions and the wizard removes the current partition configuration and  
assigns the tape drives and storage slots as evenly as possible to the partitions. Any extra tape drives or  
slots are assigned to the first partition.  
Use the Basic Partition Wizard to configure partitions that will have similar resources or to configure the  
number of barcode characters to report to the host application and whether to report them from the left or  
right end of the label for a library with a single partition.  
• Expert Partition Wizard  
You add or remove partitions from the current partitions configuration and then edit each partition config-  
uration to add or remove library resources.  
Use the Expert Partition Wizard to configure partitions that will have different resources or to adjust  
resource assignments for existing partitions or those created with the Basic Partition Wizard.  
• The library will go off line while partitions are being configured. Ensure that all host operations are idle  
before running a partition wizard.  
• To use backup software, leave the automatic cleaning function disabled (default setting). Enabling the  
setting causes a conflict error between the automatic cleaning function and the cleaning function of the  
backup software.  
For operations with the LTFS option, the automatic cleaning function can be enabled. Refer to "3.8 Clean-  
ing the Tape Drive" in "FUJITSU Storage ETERNUS LT series Tape Libraries LTFS Option User's Guide" for  
details.  
2.5.13.1 Using the Basic Partition Wizard  
Procedure  
1
Click Configuration > Partition > Basic Wizard to start the wizard.  
The Information screen displays the existing partitions, which will be deleted by the wizard.  
2
3
Click Proceed.  
Click Next.  
The Create Partition Scheme screen displays the number of slots, mailslots, tape drives, and  
maximum available partitions for the library.  
If you want to enable or disable the mailslots, Cancel out of the wizard and update the mailslot con-  
figuration before configuring partitioning.  
4
Select the number of partitions.  
53  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
5
Select the number of barcode characters reported to the host application.  
This option provides interchange compatibility with libraries with more limited barcode reading capa-  
bilities. The maximum length is 15 and the default is 8. This configuration will apply to all partitions.  
The industry standard length for LTO barcode labels is eight characters. Barcode labels longer than  
eight characters might scan incorrectly, particularly if they are not high quality labels.  
6
7
Select whether to report the barcode characters from the left or right end of the barcode  
label to the host application when reporting fewer than the maximum number of charac-  
ters.  
For example, when reporting only six characters of the barcode label "12345678", if alignment is left,  
the device will report 123456. If alignment is right, the device will report 345678. The default is left.  
Click Next.  
For operations with the backup software, the automatic cleaning function of the tape drive  
must not be used. Leave the Auto Clean checkbox unselected.  
For operations with the LTFS option, the automatic cleaning function can be enabled. Refer to "3.8  
Cleaning the Tape Drive" in "FUJITSU Storage ETERNUS LT series Tape Libraries LTFS Option User's  
Guide" for details.  
8
9
Click Next.  
The Finish Configuration screen displays the proposed allocation of library resources into  
partitions.  
■ To update the configuration, click Back.  
■ To have the wizard configure partition as shown, click Finish.  
After the wizard reconfigures the partition, the library will come on line automatically.  
■ To exit the wizard, click Cancel or Exit.  
End of procedure  
You can use the Expert Partition Wizard to adjust the allocation of resources after creating the partitions with  
the Basic Partition Wizard.  
54  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.13.2  
Using the Expert Partition Wizard  
Use the wizard to configure one partition at a time.  
If you want to enable or disable the mailslots, Cancel out of the wizard and update the mailslot configuration  
before configuring partitioning.  
■ To add/modify a partition  
Procedure  
1
2
Click Configuration > Partition > Expert Wizard to start the wizard.  
The Create Partition Scheme screen lists the current partitions, if any, and the free resources.  
To add a partition, click Add.  
The Add button will only be active if there are available resources. If there are no available resources,  
either edit a partition and release resources from it or remove a partition that contains extra  
resources.  
3
4
5
Click Next.  
Enter a partition name in "Partition Name".  
In "Barcode Label Length Reported To Host", select the number of barcode characters  
reported to the host application.  
This option provides interchange compatibility with libraries with more limited barcode reading capa-  
bilities. The maximum length is 15 and the default is 8. This configuration will apply to all partitions.  
The industry standard length for LTO barcode labels is eight characters. Barcode labels longer than  
eight characters might scan incorrectly, particularly if they are not high quality labels.  
6
In "Barcode Label Alignment Reported To Host", select whether to report the barcode charac-  
ters from the left end or right end of the barcode label to the host application when report-  
ing fewer than the maximum number of characters.  
For example, when reporting only six characters of the barcode label "12345678", if alignment is left,  
the device will report 123456. If alignment is right, the device will report 345678. The default is left.  
55  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
7
When enabling the key management function for partitions, select the [Encryption Mode]  
checkbox (only when the key management function option is used).  
This setting can only be changed by the security administrator account.  
As an exception, administrator accounts that are granted privileges by the security administrator can  
change this setting. For details, refer to "2.1.3.2 Setting the Key Management Function (Firmware  
Version 7.90 or Later)" in "FUJITSU Storage ETERNUS LT260 Tape Library Key Management Function  
Option User's Guide".  
8
9
Click Next.  
In the Assign Storage Slots screen, use the >> and << buttons to assign slots to the new par-  
tition and then click Next.  
10 In the Assign Mail Slots screen, use the >> and << buttons to assign mailslots to the new  
partition and then click Next.  
Individual mailslot elements cannot be shared between partitions. Importing or exporting cartridges in  
a partition without an assigned mailslot will require magazine access, which will take the library off  
line.  
11 In the Assign Drives screen, use the >> and << buttons to assign tape drives to the new par-  
tition and then click Next.  
12 If the partition has multiple tape drives, select the tape drive that will host the SCSI commu-  
nication for the partition and then click Next.  
The lowest numbered tape drive in the partition is the default.  
13 Verify the partition configuration and then click Finish.  
After the wizard reconfigures the partition, the library will come on line automatically.  
End of procedure  
■ To remove a partition  
Procedure  
1
2
Select the partition, click Remove, and then click Next.  
Verify that you want to remove the partition and then click Finish.  
After the wizard removes the partition, the library will come on line automatically.  
End of procedure  
When deleting a partition that has the key management function enabled, perform it with the Security role.  
The relevant partition cannot be deleted with the Administrator role.  
56  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.14 Configuring Key Management Function  
After logging in with the security account, the Configuration > Encryption screen can be selected. For the  
default library state, the hardware encryption function of the tape drive is set to be used according to the  
backup software. To use the hardware encryption function of a tape drive with a single library, the Key Man-  
agement Function Option is required.  
When using the Key Management Function Option, refer to "FUJITSU Storage ETERNUS LT260 Tape Library Key  
Management Function Option User's Guide".  
57  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.15 Configuring User Account Settings (for Firmware Versions 7.80 and Earlier)  
From the Configuration > User Accounts screen, you can set the password for the user or administrator  
accounts.  
Select the user and then enter the new password twice. The password must contain 8-16 characters, which can  
include upper and lowercase letters, numbers, and special characters.  
For firmware versions 7.90 and later, the settings related to remote panel access have been integrated in the  
[Configuration > Web Management] menu. When performing a configuration, refer to "2.5.18 Configuring  
the Access Management Setting to the Remote Panel" (page 68).  
In addition, when performing user account settings with firmware versions 7.90 and later, refer to "2.5.16  
Configuring User Account Settings (for Firmware Versions 7.90 and Later)" (page 60).  
Figure 2.19 User accounts settings  
• user  
The user account allows access to library status information and does not allow access to configuration,  
maintenance, or operation features. The initial password is "std00001". Setting a user password restricts  
access to status information to only those who know the user password.  
• administrator  
Setting an administrator password provides access to the administrator functions with the remote panel or  
operator panel, and restricts access to the administrator functions to only those who know the administra-  
tor password. The initial administrator password is "adm00001".  
58  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
• security  
In addition to the functions that are available when logged in as the administrative user, the key manage-  
ment function can be set. After the Key Management Function Option is purchased, the setting for the key  
management function is available.  
The initial password is "security". Before the password is changed, all the management functions can be  
used without limitations from the operator panel, but they cannot be used from the remote panel. After  
the security administrator password is changed on the operator panel, the password can be set from both  
panels.  
■ Restricted RMI login  
The administrator has the possibility to set login restrictions for administrator and security login. To enable  
the restriction mode, select the "Restricted Remote Management Interface (RMI) Login:" checkbox. If the  
restriction mode is enabled the administrator and the security are not allowed to login via the remote panel.  
The administrator has to disable the restriction mode by logging into the operator panel.  
Only the administrator is allowed to set and reset the restricted the remote panel login.  
■ Allow magazine and mailslot access  
The administrator can give users access permission to magazines by selecting the "Allow magazine access by  
the "user" user account:" checkbox.  
The administrator can give users access permission to mailslots by selecting the "Allow mailslot access by the  
"user" user account:" checkbox.  
59  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.16 Configuring User Account Settings (for Firmware Versions 7.90 and Later)  
From the Configuration > User Accounts > Local User Accounts screen, you can add accounts, change roles, and  
configure user accounts such as the password.  
Figure 2.20 User account settings  
In the Configuration > User Accounts > Local User Accounts screen, a list of configurable accounts among those  
who are logged in are displayed. The displayed contents are as follows.  
• Name  
Account name  
• User Role  
Account type  
- User  
The user account allows access to library status information and does not allow access to configuration,  
maintenance, or operation features. The initial password is "std00001". Setting a user password  
restricts access to status information to only those who know the user password.  
- Administrator  
An administrator account provides access to almost all the administrator functions of the library from  
the remote panel or operator panel. By setting a password, access to the administrator functions is  
restricted to only users who know the administrator password.  
The default administrator password of the library is "adm00001".  
- Security  
In addition to the functions that the Administrator account can use, the security administrator can  
enable/disable SSL and set the key management function. The key management function can be used  
by purchasing the Key Management Function Option.  
The default password is "security".  
• Status  
Login state of the account.  
- Connected  
The account is logged in.  
- Disconnected  
The account is not logged in.  
- Disconnected/Locked  
The account is locked and cannot be used to log in.  
60  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
• Last Activity  
The last day and time the account logged in.  
The configurable account type differs depending on the account used to log in. The Administrator account  
can configure the "User" and "Administrator" accounts and the Security Administrator account can configure  
the "Security" account. In addition, for the password setting, passwords that do not satisfy the specified  
requirements cannot be used. This requirement can be changed to meet your security requirements. For  
details, refer to "2.5.17 Configuring Password Requirements (for Firmware Versions 7.90 and Later)" (page  
66).  
61  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.16.1 Adding an Account  
Procedure  
1
2
Click [Add User+].  
Enter an account name to add in [Name] and select an account type for "Role" in the expanded input  
window.  
3
4
Enter the password twice.  
Click [Add].  
Figure 2.21 Adding an Account  
End of procedure  
The password set here is for the initial login. For newly added accounts, the password must be changed by  
the user the first time they log in. Perform the password setting as instructed.  
For accounts whose User Role is Administrator or Security, most of the library functions can be used. From a  
security perspective, add a limited number of accounts and issue those accounts to trusted users only.  
62  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.16.2 Changing the Account Password  
Procedure  
1
2
3
4
Click an account to change its password.  
From [Actions], select [Modify Password].  
Enter the new password twice in the expanded input window.  
Click [Modify].  
Figure 2.22 Changing the Account Password  
End of procedure  
When changing the password of a locked account, the lock is released when the password is changed. For  
details about locked accounts, refer to "2.5.17 Configuring Password Requirements (for Firmware Versions  
7.90 and Later)" (page 66).  
If the user account whose password is to be changed and the account used to change it is different (for  
example, when the administrator changes the password of a user account), the user must set a password  
again when logging in for the first time after the password is changed. Follow the instruction to set the pass-  
word.  
63  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.16.3 Changing the User Account Role  
By giving permission to operate the magazine/mailslot, tape cartridges can be removed from the library  
even with a User account.  
For security purposes, give permission only to reliable users.  
Procedure  
1
2
From [Actions], select [Modify Role Permissions].  
Select the role to change in the expanded input window.  
• Allow magazine access by the "User role"  
Allow the User account to operate the magazine.  
• Allow mailslot access by the "User role"  
Allow the User account to operate the mailslot.  
3
Click [Modify].  
Figure 2.23 Changing the User Account Role  
End of procedure  
64  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.16.4 Deleting an Account  
Procedure  
1
2
3
Select the account to delete.  
From [Actions], select [Remove User].  
In the expanded confirmation window, click [Yes].  
Figure 2.24 Deleting an account  
End of procedure  
The only accounts that can be deleted are the ones that have been added. The default accounts (user,  
administrator, security) cannot be deleted.  
65  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.17 Configuring Password Requirements (for Firmware Versions 7.90 and Later)  
This operation can only be executed from the remote panel.  
The settings requirements used when the account password is set can be configured in the [Configuration >  
User Accounts > User Accounts Settings] screen.  
The requirements that can be configured are as follows. After selecting a requirement, click [Submit] to reflect  
the setting.  
• Minimum Number Of Characters  
Sets the minimum number of characters for the password. The range of characters that can be set is 8 to  
20.  
• Minimum Number Of Upper Case Alphabetic Characters (A-Z)  
Sets the minimum number of uppercase letters. The range of uppercase letters that can be set is 0 to 3.  
• Minimum Number Of Lower Case Alphabetic Characters (a-z)  
Sets the minimum number of lowercase letters. The range of lowercase letters that can be set is 0 to 3.  
• Minimum Number Of Numeric Characters (0-9)  
Sets the minimum number of numeric characters. The range of numeric characters that can be set is 0 to 3.  
• Minimum Number Of Special Characters (!@#$%^&*()_+-={}|[]\;':"<>?,./)  
Sets the minimum number of special characters. The range of special characters that can be set is 0 to 3.  
• Maximum Number Of Identical Consecutive Characters  
Sets the maximum number of consecutive identical characters that can be used. The range of consecutive  
identical characters that can be set is 1 to 3. If Unlimited is selected, there is no limit.  
• Maximum Number Of Failed Logins Before Password Is Locked  
Sets the maximum number of failed login attempts before the account is locked. The range of login  
attempts that can be set is 1 to 10. If Unlimited is selected, there is no limit.  
• Maximum Number Of Days Before Password Must Be Changed  
Sets the maximum number of days the same password can be used. The password must be changed within  
the period. The range of days that can be set is up to 365. If Unlimited is selected, there is no limit.  
• Number Of Password Changes Before An Old Password Can Be Used Again  
Sets the number of password changes before a previously used password can be reused. The range of pass-  
word changes that can be set is up to 6. If 0 is set, there is no limit.  
66  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
Do  
CAUTION  
• If "Maximum Number Of Failed Logins Before Password Is Locked" is not set  
to Unlimited, the account is locked if the number of failed login attempts  
reaches the set value.  
Locked accounts cannot log in to the remote panel, so make sure to enter  
the correct password.  
If an account is locked or cannot be login into due to a lost password, take  
the following action for each account:  
- user  
Contact the Administrator and request a new password.  
- administrator  
A one-time password must be issued. Contact the maintenance engi-  
neer.  
- security  
Because the security account is the highest ranking security account,  
the password cannot be reissued. If the security account cannot log in,  
a factory reset is required.  
Save the setting information and export the encryption key before con-  
tacting your maintenance engineer.  
Figure 2.25 Password setting requirements  
67  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.18 Configuring the Access Management Setting to the Remote Panel  
Configure the settings for access management to the remote panel on the [Configuration > Web Management  
screen.  
• The functions related to certificates can only be used in the remote panel.  
• For firmware versions 7.90 and later, the setting items related to access management of the remote panel  
have been revised and more detailed settings are available to further enhance the security. For details,  
check the setting method for each item. The items added for 7.90 and later are listed with "for firmware  
versions 7.90 and later".  
Figure 2.26 Access management setting to the remote panel (for firmware versions 7.80 and earlier)  
68  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.5 Configuring the Library  
Figure 2.27 Access management setting to the remote panel (for firmware versions 7.90 and later)  
69  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.18.1 Enabling SSL  
Access to the remote panel using Secure Socket Layer (SSL) encrypted communication can be enabled or dis-  
abled in [Secure Communications] on the [Configuration > Web Management] screen. The default is disable.  
For firmware versions 7.80 and earlier, the [Secure Communications] item is not available.  
Direct operation is available on the [Configuration > Web Management] screen.  
To enable SSL, select the checkbox and click [Submit].  
If SSL is enabled, https must be used to connect to the remote panel.  
SSH is used for maintenance work. It cannot be used by the customer.  
Figure 2.28 Enabling the SSL setting  
70  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.18.2 Certificate Settings (for Firmware Version 7.90 and Later)  
In [Certificate Settings] on the [Configuration > Web Management] screen, enable SSL and select the self  
signed certificate to use for https connections.  
• Use Self Signed Certificate  
Uses the default self signed certificate of the library.  
• Use Custom Certificate  
Uses the self signed certificate created by the user. If a self signed certificate is not created, this item can-  
not be selected.  
For information about creating a self signed certificate, refer to "2.5.18.3 Creating a Self Signed Certificate"  
(page 72).  
Figure 2.29 Certificate settings  
71  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.18.3 Creating a Self Signed Certificate  
Create a self signed certificate for the LT260 in [Create Custom Certificate] on the [Configuration > Web Man-  
agement screen.  
For firmware versions 7.80 and earlier, the [Create Custom Certificate] item is not available.  
Direct operation is available on the [Configuration > Web Management] screen.  
• Set the RMI timeout value to 30 minutes. For information about setting the RMI timeout value, refer to  
"2.5.7 Configuring the RMI Timeout Setting (for Firmware Versions 7.80 and Earlier)" (page 41) for firm-  
ware versions 7.80 and earlier, and "2.5.18.5 Setting the Session Timeout Period of the Remote Panel (for  
Firmware Versions 7.90 and Later)" (page 79) for 7.90 and later.  
• For https connections to RMI using the created self signed certificate, the signed CA public certificate (root  
certificate) in the LT260 self signed certificate must be saved to the trusted Root Certification Authorities  
store of the client computer.  
Procedure  
1
On the [Create Custom Certificate] screen, click [Start Certificate Wizard].  
Figure 2.30 Self signed certificate creation screen  
72  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2
Start the wizard and when the [Information] screen is displayed, click [Next].  
Figure 2.31 Information screen  
73  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
3
On the [Certificate Signing Request] screen (Figure 2.32), enter the appropriate data in the  
seven fields and generate a Certificate Sign Request (CSR).  
For the data to be entered, contact the security administrator. When all seven fields are  
entered, [Generate CSR] becomes selectable. Click [Generate CSR] to generate the CSR.  
Figure 2.32 Certificate Signing Request screen 1  
4
5
Copy the entire contents of the generated CSR displayed in the "Certificate Sign Request:"  
field.  
Create a Signed Certificate from the copied CSR.  
Contact the security administrator for information about creating a Signed Certificate.  
74  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
6
Click [Next].  
If the Signed Certificate is created from the Certificate Signing Request, make sure to complete this  
procedure up to Step 7 within 30 minutes. After 30 minutes, the RMI timeout setting is activated and  
the CSR information generated in Step 3 becomes invalid. Once the CSR information becomes invalid,  
it cannot be used again and the process must be started again from Step 3.  
Figure 2.33 Certificate Signing Request screen 2  
75  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
7
Paste the Signed Certificate in the "Signed Certificate:" field and click [Next].  
Figure 2.34 Signed Certificate screen  
76  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
8
When the application process of the self signed certificate is displayed on the [Finish]  
screen (Figure 2.35), click [Finish].  
Part of the [Apply Certificate And Reload Page] task is executed when [Finish] is clicked.  
Figure 2.35 Finish screen  
End of procedure  
77  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.18.4 Backing Up and Restoring the Self Signed Certificate (for Firmware Versions 7.90 and Later)  
The self signed certificate created for the LT260 can be backed up and restored using [Backup Custom Certifi-  
cate] and [Restore Custom Certificate] on the [Configuration > Web Management] screen.  
■ Backing up the self signed certificate  
Procedure  
1
Click [Backup Custom Certificate].  
Figure 2.36 Backing up the self-signed certificate  
2
Specify the save destination and save the self signed certificate as a file.  
End of procedure  
■ Restoring the self signed certificate  
Procedure  
1
In [Restore Custom Certificate], click [Browse] to select the location of the saved self signed  
certificate.  
Figure 2.37 Restoring the self signed certificate  
2
Click [Restore Custom Certificate].  
End of procedure  
78  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.18.5 Setting the Session Timeout Period of the Remote Panel (for Firmware Versions 7.90 and  
Later)  
Set the session timeout period of the remote panel from [Session Timeout] on the [Configuration > Web Man-  
agement] screen.  
To change the session timeout period, select a time from the [Select how many minutes a user should stay  
logged in] dialog box and click [Submit]. The available selections are "5 min" and "30 min".  
Figure 2.38 Setting the session timeout  
2.5.18.6 Setting Login Session Locking Function (for Firmware Versions 7.90 and Later)  
Enable or disable session locking to the remote panel and operator panel from [OCP/RMI Session Locking] on  
the [Configuration > Web Management] screen. The default is disable. To enable the session locking function,  
select the checkbox and click [Submit].  
If the login session locking function is enabled, logins to the remote panel and operator panel are not allowed  
until the currently logged in user is logged out.  
Figure 2.39 Setting login session locking function  
79  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.5 Configuring the Library  
■ When the login session locking function is disabled  
If a login is performed while another user is logged in, a warning message is displayed indicating that another  
user is logged in. If [Login] is clicked, the logged in user is forcibly logged out and a login can be performed.  
Figure 2.40 Disabled login session locking function  
■ When the login session locking function is enabled  
If a login is performed while another user is logged in, a warning message is displayed indicating that another  
user is logged in. A login cannot be performed until the currently logged in user logs out.  
Figure 2.41 Enabled login session locking function  
80  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.5 Configuring the Library  
2.5.18.7 Remote Panel Restriction Setting (for Firmware Versions 7.90 and Later)  
Enable the remote panel restriction setting from [Restricted Remote Management Interface (RMI) Login] on  
the [Configuration > Web Management] screen. The default is disable. To enable the remote panel restriction  
setting, select the checkbox and click [Submit].  
If the remote panel restriction setting is enabled, only the User account can log in to the remote panel. How-  
ever, the library status information can be checked by logging in with the User account.  
Other than using the remote panel for a status check, all other operations are restricted. Execute library  
operations from the operator panel. The same function also removes the restriction.  
Figure 2.42 Remote panel restriction setting  
81  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6  
Maintaining the Library  
Click or tap [Maintenance] in the home screen to access the library maintenance function. From the list dis-  
played in the center pane in the operator panel or the right pane in the remote panel, select the item to con-  
figure. Refer to "1.3 Menu Layout" (page 16) for the items.  
For items with a sub-menu, click or tap the item to expand the sub-menu.  
2.6.1  
Library Tests  
2.6.1.1  
System Test  
The system test exercises overall library functionality by moving the tape cartridges within the library.  
• During each cycle the library will move a tape cartridge from a configured slot to an empty slot and then  
return it to its original slot. You can set the number of cycles for the test. If the test is canceled, the library  
will return the cartridge to its original slot.  
• The library will not move cleaning cartridges during the test.  
• The test operates over the whole library and does not take into account partition configuration.  
• During the test the library is off line.  
To run the system test, navigate to the Maintenance > Library Tests > System Test screen, select the number of  
cycles and then click Start Test.  
Figure 2.43 System test  
82  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.1.2  
Slot to Slot Test  
The slot to slot test randomly exchanges cartridges between slots to verify that the library is operating cor-  
rectly. At the end of the test the cartridges are NOT returned to their original slots. If a tape cartridge is moved  
to an incompatible tape drive, the tape drive will reject the tape cartridge.  
The test can move cartridges between partitions.  
To run the slot to slot test, navigate to the Maintenance > Library Tests > Slot to Slot Test screen, select the  
number of cycles and click Start Test.  
Figure 2.44 Slot to slot test  
83  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.1.3  
Element to Element Test  
The element to element test moves a selected cartridge to a selected slot or tape drive, and then returns it to  
the original slot. You can select the number of times to move the selected cartridge to the destination location  
and back.  
The element to element test is intended to show that the library is operating correctly. To diagnose problems  
with the robotic assembly or verify that it has been correctly replaced, use the robotic test.  
Figure 2.45 Element to element test  
84  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
■ To run the element test  
Procedure  
1
2
Navigate to the Maintenance > Library Tests > Element to Element Test screen.  
Select a cartridge from the Source Elements list.  
To select from a subset of the cartridges:  
2-1 Click Filter On.  
2-2 Enter characters into the search box and then click Search.  
The Source Elements list is updated to only include cartridges with a barcode label including the  
search characters.  
3
Select a location from the Destination Elements list.  
Select the number of cycles.  
4
5
Click Start Test.  
End of procedure  
85  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.1.4  
Position Test  
The position test moves the robotic assembly vertically between two elements. The number of movements  
can be specified.  
This test does not move cartridges.  
Figure 2.46 Position test  
86  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
■ To run the position test  
Procedure  
1
2
Navigate to the Maintenance > Library Tests > Position Test screen.  
Select a cell from the Source Elements list.  
To select from a subset of the cell:  
(1)Click Filter On.  
(2)Enter characters into the search box and then click Search.  
The Source Elements list is updated to only include cartridges with a barcode label including the  
search characters.  
3
4
5
Select a destination cell from the Destination Elements list.  
Select the number of cycles.  
Click Start Test.  
End of procedure  
87  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.1.5  
Wellness Test  
• The wellness test exercises a general health check on the library functionality by running the following  
partial tests:  
- Basic Hardware Review  
- Robotics Initialization Test  
- Barcode Scanning Test  
- Magazine/Mailslot Unlock Motor Test  
- Move Media Test  
• Running the test requires at least one drive and one tape carting in the library.  
• After the test has been started the Stop Test button is active. Clicking the button will abort the wellness test  
but not before the current partial test has been completed.  
• The test operates over the whole library and does not take into account partition configuration.  
• During the test the library is off line.  
• The Info column notifies the user about the status and result of each partial test.  
To run the wellness test, navigate to the Maintenance > Library Tests > Wellness Test screen, and then click  
Start Test.  
Figure 2.47 Wellness test  
88  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.1.6  
Robotic Test  
The robotic test performs a full inventory and exercises all robotic assembly movements and sensors.  
To run the robotic test, navigate to the Maintenance > Library Tests > Robotic Test screen, then click Start Test.  
Figure 2.48 Robotic test  
2.6.1.7  
Operator Panel Test and Calibration  
To perform a test or maintenance operation for the operator panel, navigate to the Maintenance > Library  
Tests > Operator Panel Test screen, select the operation, and then click Start. Follow the instructions on the  
screen.  
Figure 2.49 OCP test  
• LED test  
Illuminates each of the front panel LEDs.  
• Touch panel calibration test  
Allows you to calibrate the front panel touch screen.  
• OCP Reboot  
Restarts the operator panel.  
89  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.2  
Viewing Log Files  
● Operate from the operator panel  
To view the library log files, navigate to the Maintenance > View Logs screen and then select one of the  
logs.  
● Operate from the remote panel  
To view the library log files, navigate to the Maintenance > Logs and Traces > View Logs screen and then  
select one of the logs.  
The available logs are as follows. In addition, for firmware versions 7.90 and later, all the following logs are  
shown at once if [Show All] is selected.  
• Event Ticket Log  
Records library error and warning events.  
• Information Log  
Records library information warnings.  
• Configuration Log  
Records configuration changes.  
If [Close all open tickets] is clicked, all the logs that are being displayed become hidden.  
After the [Include closed tickets] checkbox is selected, the logs that were hidden by clicking [Close Ticket] or  
[Close all open tickets] are also displayed.  
If the Attention LED is on, clicking [Close ticket] or [Close all open tickets] turns the Attention LED off.  
Do not click [Clear log]. If [Clear log] is clicked, all the required information for a maintenance is cleared.  
Figure 2.50 View logs  
90  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
The log entries are displayed in order of most recent to oldest. The log entries contain a date and time code,  
event code, severity, component identifier and event details.  
The format for the date and time is: DD.MM.YYYY HH.MM.SS  
• DD.MM.YYYY  
The date displayed as Day.Month.Year  
• HH.MM.SS  
The time displayed as Hour.Minute.Second  
After the log that is being displayed is clicked, the detailed information is displayed.  
Figure 2.51 Detailed view example for logs  
After [Close Ticket] is clicked, this log is hidden.  
After [Close] is clicked, the detailed view screen is closed.  
91  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.3  
Managing System Firmware  
The firmware version currently installed on the library is displayed in the library status area on the Home  
page. You update the library firmware from the Maintenance > Software Upgrades > System Firmware screen.  
Figure 2.52 Upgrades system firmware  
To update library firmware from the remote panel, click Browse and select the firmware file from the local  
computer.  
When you update the library firmware, the library will update the firmware of the expansion modules to a  
compatible version.  
92  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.4  
Managing Drive Firmware  
Drive firmware can be updated on multiple tape drives of the same type at the same time. Drive firmware can  
only be updated from the remote panel. Each tape drive will only accept appropriate firmware.  
To see the firmware version currently installed in the tape drives, navigate to the Status > Drive Status screen.  
Figure 2.53 Upgrades drive firmware  
■ To update drive firmware from the remote panel  
Procedure  
1
2
Navigate to the Maintenance > Software Upgrades > Drive Firmware screen. The tape drives  
are organized by drive type.  
Select the type of tape drive to update and then select one or more of the tape drives from  
the expanded list.  
3
4
Click Browse, and then select the file from the local computer.  
Click Submit.  
End of procedure  
93  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.5  
Downloading Drive Logs  
From the Maintenance > Download Drive Logs screen, logs can be downloaded from any tape drive.  
Customers may be asked by maintenance personnel to acquire logs for troubleshooting.  
Figure 2.54 Download drive logs  
Procedure  
1
Select a tape drive to download the log.  
The following items are displayed in the list of drive logs.  
• Drive  
The tape drive number. Tape drives are numbered starting with one from the physical bottom of the  
library to the top.  
• Type  
The drive form factor (half height) and interface  
• Firmware  
The current drive firmware version  
• Serial  
The tape drive serial number  
• Unit  
The module containing the tape drive  
• Partition  
The logical library (or partition) associated with the tape drive  
94  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2
Select a log to download.  
• Current Log (*1)  
Creates and saves a new log from the tape drive.  
• Log From Last Unload (*1)  
Saves the log that was automatically created after the last cartridge was unloaded from the tape  
drive.  
• Regular Dump (*2)  
Saves the tape drive error information that is stored in the nonvolatile memory. The errors that  
occur just before saving may not be saved.  
• Forced Dump (*2)  
Saves the error information up to the point when the Dump was executed. Since the size of the  
memory that is used for recording is small, if a considerable amount of time elapses after the error  
occurred, there may be cases when the error information is not saved.  
*1: Displayed if the model name of the tape drive is in the following list:  
LT26ASHE, LT26ASHL (LTO-5 SAS HH drive option)  
LT26AFHE, LT26AFHL (LTO-5 FC HH drive option)  
LT26ASJE, LT26ASJL (LTO-6 SAS HH drive option)  
LT26AFJE, LT26AFJL (LTO-6 FC HH drive option)  
*2: Displayed if the model name of the tape drive is in the following list:  
LT26BSKE, LT26BSKL (LTO-6 SAS HH drive option -I)  
LT26BFKE, LT26BFKL (LTO-6 FC HH drive option -I)  
LT26BSME, LT26BSML (LTO-7 SAS HH drive option -I)  
LT26BFME, LT26BFML (LTO-7 FC HH drive option -I)  
LT26BSNE, LT26BSNL (LTO-8 SAS HH drive option -I)  
LT26BFNE, LT26BFNL (LTO-8 FC HH drive option -I)  
3
Check the tape drive, and then click Save.  
End of procedure  
95  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.6  
Downloading Log and Trace Files  
This operation can be executed from only remote panel operation.  
Figure 2.55 Download logs and traces  
To download the library log and trace files from the remote panel, navigate to the Maintenance > Logs and  
Traces > Download Logs and Traces screen and then click Save.  
Customers may be asked by maintenance personnel to acquire logs for troubleshooting.  
2.6.7  
Rebooting the Library  
From the Maintenance > System Reboot screen, click Reboot.  
Figure 2.56 Rebooting the library  
96  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
       
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.8  
Tape Drive Reboot  
From the Maintenance > Drive Reboot screen, you can reboot the tape drives.  
Only one tape drive can be selected for reboot.  
Procedure  
1
Select the tape drive you want to reboot.  
Figure 2.57 Tape drive reboot  
2
Click Yes on the dialog popup to start the reboot process.  
End of procedure  
97  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.6 Maintaining the Library  
2.6.9  
Controlling the UID LED  
The UID LEDs are a pair of blue LEDs — one on the operator panel and the other on the base module controller.  
The UID LEDs are useful for identifying the library in a data center. The UID LEDs are operated synchronously  
and controlled by the user. From the Maintenance > UID LED Control screen you can see whether the LEDs are  
lit, and toggle the status.  
Figure 2.58 UID LED control  
2.6.10 Moving the Robotic to the Base Module  
Before extending a module from the rack, the robotic assembly must return to its park position in the base  
module. Under normal circumstances, when the library is powered off using the front power button the robot  
automatically parks and locks into the base module behind the operator panel. After powering off the library  
and before proceeding with extending a module from the rack, look inside the base module window to verify  
that the robotic assembly is behind the operator panel.  
If the library did not move the robotic assembly to its park position, you can do so from the Maintenance >  
Move Robotic to Base Module screen.  
Figure 2.59 Move robotic to base module  
98  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
       
Chapter 2 Operating the Library  
2.7 Operating the Library  
2.7  
Operating the Library  
Click or tap [Operation] in the home screen to use the library operation function. From the list displayed in the  
center pane in the operator panel or the right pane in the remote panel, select the item to configure. Refer to  
"1.3 Menu Layout" (page 16) for the items.  
For items with a sub-menu, click or tap the item to expand the sub-menu.  
2.7.1  
Moving Media  
From the Operation > Move Media screen you can move a tape cartridge located in a source element to an  
available destination element within the same partition.  
Figure 2.60 Move media  
• Source Elements  
Tape drives, enabled mailslots, and storage slots that contain a tape cartridge  
• Destination Elements  
Tape drives, enabled mailslots, and storage slots that do not contain a tape cartridge  
Tape drives are listed at the top of each element list and listed in the order of their drive numbers.  
Tape drives are numbered from the physical bottom of the library starting with Drive (1).  
Slots are listed in the order of the slot numbers. Slots are numbered m.s, where m is the module number and  
s is the slot within the module.  
99  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.7 Operating the Library  
■ Filtering Based on Barcode  
This function can be used from only remote panel operation.  
To see a subset of the cartridges in the library, enter some or all of the barcode label characters in the search  
area and click Search. The Source Element list updates to display only the cartridges with labels that include  
the characters in the search box.  
To perform a different search or display all of the available cartridges, click Barcode Filter Off.  
■ Moving a Cartridge  
Procedure  
1
2
3
Select the cartridge from Source Elements.  
Select the destination location from Destination Elements.  
Click Submit.  
End of procedure  
2.7.2  
Opening the Mailslot  
From the Operation > Open Mailslot screen you can see the status and unlock any enabled mailslots in the  
library.  
This function can be accessed directly from [Open Mailslot] on the home screen without going through the  
[Operation] screen.  
Be careful not to remove the wrong tape cartridge or install a tape cartridge in the wrong partition slot.  
For this reason, check the following points before opening the mailslot.  
• Number and position of the mailslot to open  
• Number and position of the slot to load or unload the tape cartridge  
• Slot allocation of each partition  
For details on how to check the above information, refer to "2.8.3 Using Inventory Graphical View" (page  
111) and "2.8.4 Partition Map Graphical View" (page 113).  
100  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.7 Operating the Library  
Figure 2.61 Open mailslot  
To open a mailslot, click Open for the appropriate mailslot. The library will release the lock. You can then pull  
the mailslot out of the library to access the mailslot.  
The mailslot must be enabled before it can be opened and the mailslot will relock after 30 seconds. To  
enable a mailslot or to change the relock time, see "2.5.12 Enabling or Disabling Mailslots" (page 51).  
Do Not  
WARNING  
Hazardous moving parts exist inside this product. Do not insert tools or any por-  
tion of your body into the interior of the library through the mailslot safety door.  
101  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.7 Operating the Library  
2.7.3  
Opening a Magazine  
From the Operation > Open Magazine screen you can unlock any magazines.  
This function can be accessed directly from [Open Magazine] on the home screen without going through the  
[Operation] screen.  
Be careful not to remove the wrong tape cartridge or install a tape cartridge in the wrong partition slot.  
For this reason, check the following points before opening the mailslot.  
• Number and position of the magazine to open  
• Number and position of the slot to load or unload the tape cartridge  
• Slot allocation of each partition  
For details on how to check the above information, refer to "2.8.3 Using Inventory Graphical View" (page  
111) and "2.8.4 Partition Map Graphical View" (page 113).  
Figure 2.62 Open magazine  
To unlock a magazine, click Open for the magazine. The library will release the lock. You can then open the  
door and pull the magazine out of the library to access the storage slots.  
• The status of the library will become Offline when a magazine is opened.  
• The magazines will relock after 30 seconds.  
• To change the relock time, see "2.5.12 Enabling or Disabling Mailslots" (page 51).  
102  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.7 Operating the Library  
2.7.4  
Cleaning a Tape Drive  
From the Operation > Clean Drive screen you can initiate a manual tape drive cleaning operation.  
To use the auto-cleaning function, see "2.5.13 Configuring Library Partitions" (page 52) and "5.5.1 Auto-  
Cleaning Function" in "FUJITSU Storage ETERNUS LT260 Tape Library Overview".  
Figure 2.63 Clean drive  
Procedure  
1
2
3
Select a cleaning cartridge from the Source Elements list. The library uses the barcode label  
to identify cleaning cartridges.  
If no cleaning cartridges are available, load one into a mailslot or magazine slot.  
Select the tape drive to be cleaned from the Destination Elements list.  
Tape drives currently containing a cartridge are not listed. To clean a tape drive not listed, move the car-  
tridge out of the drive.  
Click Submit.  
End of procedure  
103  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.7 Operating the Library  
2.7.5  
Rescanning the Cartridge Inventory  
To have the library rescan the cartridges, navigate to the Operation > Rescan screen and click Rescan. The  
library will change to Scanning status and will be unavailable to perform other operations until the scan is  
complete.  
Figure 2.64 Rescan inventory  
104  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.7 Operating the Library  
2.7.6  
Forcing a Tape Drive to Eject a Cartridge  
The force drive media eject operation attempts to force the tape drive to eject the cartridge and place it into  
an open slot. Access to this feature requires the administrator password.  
Before performing this option, it is recommended that you attempt to eject the tape using the backup soft-  
ware or library move media operation. While a drive is being force ejected, a window indicating the process is  
ongoing should appear. No operations will be available until the force eject completes.  
If the drive has difficulty ejecting the cartridge, the media is possibly bad or damaged.  
Figure 2.65 Force drive media eject  
Procedure  
1
2
3
4
Navigate to the Operation > Force Drive Media Eject screen.  
Select the drive in the Source Elements list.  
Select the destination in the Destination Elements list.  
Click Submit.  
End of procedure  
105  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
2.8  
Viewing Status Information  
Click or tap [Status] in the home screen to access the status area. From the list displayed in the center pane in  
the operator panel or the right pane in the remote panel, select the item to configure. Refer to "1.3 Menu  
Layout" (page 16) for the items.  
For items with a sub-menu, click or tap the item to expand the sub-menu.  
2.8.1  
Viewing Library and Module Status  
Summary information and status is displayed in the top banner and left side bar. For additional library mod-  
ule configuration and status information navigate to the Status > Library Status screen.  
Figure 2.66 Library status  
106  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
■ Library information  
• Vendor  
Vendor information of the library. The vendor is FUJITSU.  
• Product ID  
Inquiry information of the library. This does not indicate the name of the library itself.  
• Serial Number  
Library serial number  
• Firmware Revision  
Version of the currently installed library firmware  
• Robotic Hardware Revision  
Hardware version of the robotic assembly installed in the current library.  
• Robotic Firmware Revision  
Version of the currently installed robotic assembly firmware. The robotic assembly firmware is bundled and  
installed with the library firmware.  
• Barcode Reader Hardware Revision  
Hardware version of the barcode reader installed in the current library.  
• Barcode Reader Firmware Revision  
Version of the currently installed barcode reader firmware. The barcode reader firmware is bundled and  
installed with the library firmware.  
• WWide Node Name  
World Wide Node Name (WWNN) that is a unique identifier of the library.  
■ Library Status  
• Library Status  
- Idle  
The library robotic is ready to perform an action.  
- Moving  
The library robotic is moving a cartridge.  
- Scanning  
The library robotic is performing an inventory of cartridges.  
- Offline  
The robotic assembly is being used by the library or is disabled.  
• Cartridge in Transport  
When applicable, displays the barcode label of the cartridge currently in the robotic assembly.  
• Total Power On Time  
Total time that the base module has been powered on since it was manufactured  
• Odometer  
Robotic assembly move count  
• Robotic Location  
Displays the module where the robotic is currently located.  
107  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
• Shipping Lock  
Indicates whether the robotic is unlocked or locked for shipment.  
■ Module status  
• Base Controller Revision or Expansion Controller Revision  
Hardware revision of the controller board currently installed in the module.  
• Left Drive Power Board  
Status of the drive power board (DC-DC converter) for the top three half-height drive slots in the module.  
• Right Drive Power Board  
Status of the drive power board (DC-DC converter) for the lower three half-height drive slots in the module.  
• Power Supply Status  
Displays the status of power redundancy.  
• Lower/Upper Power Supply Fan  
Displays the status of power supply fans.  
• Chassis Fan  
Displays the status of the chassis fan.  
108  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
2.8.2  
Using Inventory Lists  
The inventory lists display each of the elements, such as slots and tape drives, with information about the car-  
tridge stored in the element. To see the elements organized by module, from Status, navigate to Cartridge  
Inventory > List View. To see the elements organized by logical library (or partition), from Status, navigate to  
Partition map > List View.  
Figure 2.67 Inventory list  
In the Inventory List you can see:  
• Module  
The module number  
• Slot #  
The slot number in the form <module>.<slot>, where module is the module number and slot is the slot  
number  
• Barcode  
Barcode label  
• Full  
X if a cartridge is using the element  
• Gen.  
LTO generation of the cartridge  
109  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
• Partition  
The partition number  
■ Filtering by Barcode Label  
To filter the list based on barcode label, enter characters in the filter box and then click Search.  
Procedure  
1
2
Click Filter On.  
The search box is displayed.  
Enter characters into the search box and then click Search.  
The characters can be anywhere in the barcode label. The search characters are not case sensitive.  
There are no wildcards.  
End of procedure  
To disable filtering, click Filter Off.  
■ Listing Just Drives or Cartridges  
To limit the list to tape drives, click Drives.  
To limit the list to cartridges, click Cartridges.  
To see all elements, click Partition or Slots.  
■ Viewing Elements by Group  
When the list is grouped, you can expand or contract the list for each group by clicking the triangle next to the  
number in the first column. Grouping is enabled by default.  
To disable grouping, click Group Off.  
To enable grouping, click Group On.  
110  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
2.8.3  
Using Inventory Graphical View  
The inventory graphical view displays each of the elements, such as slots and tape drives, with information  
about the cartridge stored in the element. To see the elements organized by module, from Status, navigate to  
Cartridge Inventory > Graphical View. To see the elements organized by logical library (or partition), from  
Status, navigate to Partition Map > Graphical View.  
■ Inventory Graphical View  
To see the elements with the graphical view, from Status, navigate to Cartridge Inventory > Graphical View.  
Figure 2.68 Inventory graphical view  
111  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
When the mouse pointer is moved over a tape drive or cartridge, the following additional information is dis-  
played.  
Figure 2.69 Inventory graphical view (display status)  
• Drive  
LTO generation and format of the tape drive  
• Drive #  
The tape drive number  
• Serial #  
Serial number of the tape drive  
• Slot #  
The slot number in the form <module>.<slot>, where module is the module number and slot is the slot  
number  
• Barcode  
Barcode data on label  
• Generation  
LTO generation of cartridge  
• Partition  
The partition number  
• Media Loads  
The number of media loads  
• Encryption  
Indicates whether data on this media is encrypted.  
• Media Type  
The type of the media that is applicable  
• LT Encryption Key  
The type of the encryption key when the Key Management Function Option is used  
112  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
Warning state and error state for a specific tape drive or cartridge are indicated with icons.  
Figure 2.70 Inventory graphical view (display error status)  
2.8.4  
Partition Map Graphical View  
To see the elements organized by logical library (or partition), from Status, navigate to Partition Map >  
Graphical View.  
The graphical view of the partition map displays all the elements for each partition number. For normal slots,  
a partition number is displayed for every five slots. If mailslots are enabled, the partition number is displayed  
with an "M" for each mailslot.  
Even if the mailslot is disabled, the partition number is displayed for each slot.  
Figure 2.71 Partition map graphical view  
113  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
     
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
When the mouse pointer is moved over a partition layer, the following additional information is displayed.  
Figure 2.72 Partition map graphical view (display partition information)  
• Name  
Partition name  
• Barcode  
Barcode orientation  
• Media Removal  
Indicates whether media removal is allowed or prevented by the host.  
• Key Manager Type  
Encryption type  
• Partition S/N  
Serial number of the partition  
• Drive Count  
Number of tape drives in this partition  
• Slot Count  
Number of slots in this partition  
• Cartridge Count  
Number of cartridges in this partition  
• Mailslot Count  
Number of mailslots in this partition  
114  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
When the mouse pointer is moved over a tape drive, the following additional information is displayed.  
Figure 2.73 Partition map graphical view (tape drive information display)  
• Drive  
LTO generation and format of the tape drive  
• Drive #  
The tape drive number  
• Serial #  
Serial number of the tape drive  
• Partition  
The partition number  
If a cartridge is loaded in this tape drive, additional information for the cartridge is displayed as follows:  
• Barcode  
Barcode data on label  
• Generation  
LTO generation of cartridge  
• Partition  
The partition number  
• Media Loads  
The number of media loads  
• Encryption  
Indicates whether data on this media is encrypted.  
• Media Type  
The type of the media that is applicable  
115  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
 
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
• LT Encryption Key  
The type of the encryption key when the Key Management Function Option is used  
2.8.5  
Using Partition Map Configuration Status  
To see the configuration of a partition, the elements and their status, from Status, navigate to Partition Map >  
Configuration Status.  
Figure 2.74 Using partition map configuration status  
In the configuration status list you can see:  
• Partition Number  
The partition number  
• Partition Name  
The partition name  
• Partition S/N  
The partition serial number  
• Number of Drives  
Number of tape drives allocated in this partition. If the number is clicked, the detailed information of the  
tape drive is expanded.  
• Number of Slots  
Number of slots allocated in this partition  
• Number of Mailslots  
Number of mailslots allocated in this partition  
116  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
• Barcode Label Length Rep. to Host  
Barcode length reported to the host  
• Barcode Label Alignment Rep. to Host  
Barcode alignment reported to the host  
• Auto Clean  
Indicates whether automatic cleaning of tape drives is enabled or disabled.  
• Key Manager Type  
Encryption type  
• Active Control Path Drive  
LUN drive for this partition  
• LTO7+ Multi-initiator SCSI Conflict Detection  
The setting value related to multiple SCSI connections. The default is Disable and cannot be changed.  
117  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
2.8.6  
Viewing Tape Drive Status  
In the Status> Drive Status screen you can see the configuration and status of each tape drive installed in the  
library.  
Figure 2.75 Tape drive status  
118  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
2.8.7  
Viewing Network Status  
In the Status > Network Status screen you can see the network configuration and status.  
Figure 2.76 Network status  
The following can be found in the Network Status screen.  
• Host Name  
Library hostname  
• Domain Name  
The domain name set for the library  
• Protocol  
IPV4 or IPv6  
• MAC Address  
A unique identifier for the library controller network interface  
• Link Status  
Enabled or disabled  
• Link Speed  
Speed of the Ethernet connection to the library  
• Duplex  
Enabled or disabled  
119  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
■ IPv4 settings  
• DHCP  
When Enabled, the library requests an IP address from a DHCP server each time the library is powered on.  
• Address  
IP address in use by the library. If DHCP is enabled, this address was obtained from the DHCP server. When  
DHCP is not enabled, the address was configured.  
• Netmask  
The network mask of the library controller used when DHCP is not enabled.  
• Gateway  
The gateway used when DHCP is not enabled.  
• DNS 1  
IP address of the DNS server.  
• DNS 2  
IP address of the alternate DNS server. Used when DNS 1 is not responding.  
■ IPv6 settings  
• Stateless  
When Enabled, the device will generate an address for itself based on the routing information obtained  
from a router advertisement and the MAC address. The device can manage up to five global addresses at  
the same time, which can be assigned from different routers.  
• Static  
When Enabled, the library will use a statically-configured address.  
• Address  
The IPv6 address when Static Addressing Enabled is On.  
• DNS 1  
IP address of the DNS server.  
• DNS 2  
IP address of the alternate DNS server. Used when DNS 1 is not responding.  
120  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
Chapter 2 Operating the Library  
2.8 Viewing Status Information  
2.8.8  
Viewing Security Status  
In the Status > Security screen, the encryption status of the library is displayed in a list.  
For details on the displayed contents of the Key Management Function Option, refer to "FUJITSU Storage ETER-  
NUS LT260 Tape Library Key Management Function Option User's Guide".  
Figure 2.77 Viewing security status  
121  
FUJITSU Storage ETERNUS LT260 Tape Library User’s Guide -Panel Operation-  
Copyright 2019 FUJITSU LIMITED  
P3AM-8802-09ENZ0  
   
FUJITSU Storage ETERNUS LT260 Tape Library  
User's Guide -Panel Operation-  
P3AM-8802-09ENZ0  
Date of issuance: December 2019  
Issuance responsibility: FUJITSU LIMITED  
•
•
The content of this manual is subject to change without notice.  
This manual was prepared with the utmost attention to detail.  
However, Fujitsu shall assume no responsibility for any operational problems as the result of  
errors, omissions, or the use of information in this manual.  
•
•
Fujitsu assumes no liability for damages to third party copyrights or other rights arising from  
the use of any information in this manual.  
The content of this manual may not be reproduced or distributed in part or in its entirety  
without prior permission from Fujitsu.  

Toshiba Eo1 33057 User Manual
Sharp Mx B201d User Manual
Philips R6b2a260 User Manual
HITACHI 62VS69 User Manual
DELL S2721HSX User Manual
CRAFTSMAN 358.350060 User Manual
BLACK DECKER TO3215SSD User Manual
ASUS VP249H User Manual
ACER ASPIRE 1 User Manual
ACER ALTOS EASYSTORE M2 User Manual