AM / FM / TV Bands
Instant Weather
Portable Radio
with LCD Clock
OWNER'S MANUAL
RP1103
RP1103_010505.p65
16
5/1/2005, 13:51
Before We Begin
Thank you for purchasing this Emerson audio product. The Emerson brand is your
assurance of quality, performance and value.
Our engineers have included many useful and convenient features in this product.
Please be sure to read this Owner’s Manual completely to make sure you are
getting the maximum benefit from each feature.
This product was manufactured using the highest qualitycomponents and standards
of workmanship. It was tested by Emerson inspectors and found to be in perfect
working order before it left our factory. However, there is always the chance that
some problem may occur because of rough handling during shipment to the retail
store or to the final consumer.
If, after reading this Manual, you experience any problems with the operation of
this product, please refer to the instructions for obtaining service at the end of this
Manual. Emerson and Emerson retailers are committed to your satisfaction.
Once again, thanks for purchasing this Emerson audio product.
For future reference, record the serial number in the space provided.
Model No: RP1103
Serial No:
2
RP1103_010505.p65
2
5/1/2005, 11:49
IMPORTANT NOTES
• Operate controls and switches as
• Avoid installing this unit in places
exposed to direct sunlight or close to
heat radiating appliances such as
electric heaters, on top of other stereo
equipment that radiates too much
heat, places lacking ventilation or dusty
areas, places subject to constant
vibration and/or humid or moist areas.
described in the manual.
• Before turning on the power, make
certain that the power cord is properly
installed.
• When moving the set, be sure to first
disconnect the AC power cord.
NOTE: The manufacturer is not responsible for any radio or TV interference
caused by unauthorized modifications to this equipment. Such modifications
could void the User's authority to operate the equipment.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequencyenergy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
3
RP1103_010505.p65
3
5/1/2005, 11:49
PREPARATION FOR USE
Unpacking And Set Up
• Remove the radio from the carton and remove all packing material from the
radio. We suggest that you save the packing material, if possible, in the unlikely
event that your radio ever needs to be returned for service. The original carton
and packing material is the only safe way to pack your radio to protect it from
damage in transit.
• Remove any descriptive labels or stickers on the front or top of the cabinet. Do
not remove any labels or stickers from the back or bottom of the cabinet.
• Note the serial number on the bottom of your radio and write this number in the
space provided on Page 2 of this manual.
• Place your radio on a level surface such as a table, desk or shelf, convenient to
an AC outlet, out of direct sunlight, and away from sources of excess heat, dirt,
dust, moisture, humidity, or vibration.
• Unwind the AC power cord and extend it to its full length.
AC Operation
The AC power cord is located inside the battery compartment. It is permanently
attached to the radio to prevent loss.
1.) Open the battery compartment by pressing on the “
and sliding it downward in the direction of the arrows.
” marks on the cover
4
RP1103_010505.p65
4
5/1/2005, 11:49
2.) Remove the coiled AC cord form the storage compartment and extend it to its
full length.
3.) Position the cover over the battery compartment and place the cord into the
notch on the battery compartment cover as shown.
4.) Slide the battery cover upward until it snaps back into place.
Connect the AC cord to your 120V 60Hz AC outlet.
Note: When the AC power cord is connected to the outlet the power source
automatically switches to AC. You may leave batteries inside the unit if desired.
There is no battery consumption when the power cord is connected to an AC
outlet.
Caution !!
This radio is designed to operate on normal 120V 60Hz AC power only. Do not
attempt to operate the radio on any other power source. You could cause damage
to the radio that is not covered by your warranty.
This radio uses a polarized AC plug which has
one blade wider than the other. This plug will
only fit into a polarizedAC outlet. This is a safety
feature. If the plug will not fit, you may have an
older non-polarized AC outlet. Do not defeat
the safety feature by trying to file the wider
blade, or replacing the plug. Contact an
AC Outlet
electrician to replace your outdated outlet.
AC Plug
5
RP1103_010505.p65
5
5/1/2005, 11:49
Battery Operation
This unit requires 4 “AA” batteries, not included. We recommend using a well-
known brand of alkaline batteries for longest life and best performance.
1.) Open the battery compartment by pressing on the “
and sliding it downward in the direction of the arrows.
” marks on the cover
2.) If necessary, fold the AC power cord as shown and push it back into the cord
storage compartment.
3.) Insert the 4 “AA” batteries into the battery compartment as shown. Be sure to
observe the polarity markings inside the compartment. If the batteries are
inserted incorrectly the unit will not work.
4.) Slide the battery cover upward until it snaps back into place.
When the radio sound becomes weak or distorted it is time to change the batteries.
Replace all 4 batteries with fresh, new alkaline batteries at the same time. Do not
mix old and new batteries, or different types of batteries together.
BATTERY PRECAUTIONS
Follow these precautions when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery
compartment. Reversed batteries may cause damage to the device.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-Zinc) or old batteries
with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent
damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture.
(Follow battery manufacturer’s directions.)
6
RP1103_010505.p65
6
5/1/2005, 11:49
Protect Your Furniture
This model is equipped with non-skid rubber 'feet' to prevent the product from
moving when you operate the controls. These 'feet' are made from non-migrating
rubber material specially formulated to avoid leaving any marks or stains on your
furniture. However certain types of oil based furniture polishes, wood preservatives,
or cleaning sprays may cause the rubber 'feet' to soften, and leave marks or a
rubber residue on the furniture. To prevent any damage to your furniture we strongly
recommend that you purchase small self-adhesive felt pads, available at hardware
stores and home improvement centers everywhere, and apply these pads to the
bottom of the rubber 'feet' before you place the product on fine wooden furniture.
7
RP1103_010505.p65
7
5/1/2005, 11:49
LOCATION OF CONTROLS AND INDICATORS
6
7
8
9
5
4
3
10
11
12
13
2
1
14
15
1.) Speaker.
8.) LCD CLOCK.
9.) Clock MODE Button.
10.) TUNING Control.
11.) Clock SET Button.
12.) Dial Pointer.
2.)
PHONES Jack.
3.) Carrying Handle.
(Back Cabinet).
4.) Display Back LIGHT Button.
13.) Band (AM-FM/TV1-TV2) Selector
5.) WEATHER BAND FINE TUNING
Switch.
Control (Back Cabinet).
14.) VOLUME Control.
6.) WEATHER Band Button.
Power “On/OFF” Switch.
7.) FM/TV/Weather Band Telescopic
Antenna.
15.) Battery & AC Cord Compartment.
(Back Cabinet)
8
RP1103_010505.p65
8
5/1/2005, 13:55
OPERATING INSTRUCTIONS
Radio Operation
1.) Turn on the radio by rotating the VOLUME control clockwise.
2.) Move the Band Selector switch to select the desired band (AM, FM/TV1 or
TV2).
• Select AM to tune AM radio stations.
• Select FM/TV1 to tune FM radio stations and TV channels 2 through 6.
• Select TV2 to tune TV channels 7 through 13.
3.) Tune the desired station by rotating the TUNING control.
4.) Adjust the VOLUME control as desired.
5.) To turn the unit ‘Off’, rotate the VOLUME control counterclockwise until a
click sound is heard.
Weather Band Operation
This radio receives continuous U.S. Government Weather Broadcasts from the
National Oceanic and Atmospheric Administration (NOAA), part of the Department
of Commerce. This National Weather Radio service includes more than 750
transmitters covering all 50 states and adjacent coastal waters, Puerto Rico, the U.
S. Virgin Islands, and the U.S. Pacific Territories. The weather broadcasts are
transmitted on seven separate bands from 162.400 MHz to 162.550 MHz.
To hear the weather reports, press the WEATHER button on the top cabinet at any
time. If you were listening to another band the radio will automatically switch to the
weather band.
The volume level is fixed at optimum listening level on Instant Weather operation.
In order to increase or decrease the volume level, turn the volume control up or
down.
Note: Since the National Weather Radio transmitters operate at much lower
power than commercial radio stations, the volume on the weather band
will be lower than for AM/FM or TV bands. This is normal and not an
indication of any trouble with your unit. Adjust the VOLUME when listening
to the Weather Band if necessary.
9
RP1103_010505.p65
9
5/1/2005, 11:49
If you do not hear the weather reports when you press the WEATHER button, very
slowly rotate the WEATHER BAND FINE TUNING control on the back cabinet of
the radio until you are receiving the frequency of the National Weather Radio
transmitter that is broadcasting in your area. You only need to do this one time,
unless you move to a different area. In that case you might have to adjust the
WEATHER BAND FINE TUNING control again.
Antennas
AM – This unit has a built-in ferrite rod antenna, which eliminates the need for an
external antenna, and provides adequate reception in most areas. If reception is
weak, turn the unit to improve reception.
FM, TV, WEATHER BAND – The telescopic antenna on the top of the unit is for
these bands only. If reception is weak, adjust the length of the antenna.
10
RP1103_010505.p65
10
5/1/2005, 11:49
Setting The Date And Time
Note: The month and date are displayed numerically (MM/DD).
For example, February 28th is displayed as “2 28”.
1.) Press the MODE button twice. The Month display
appears.
2.) Press the SET button repeatedly to advance the display to the correct month.
3.) Press the MODE button again. The Day display
appears.
4.) Press the SET button repeatedly to advance the display to the correct day.
5.) Press the MODE button again. The Hour display
appears together with either the “A” (AM) or “P”
(PM) indicator.
6.) Press the SET button repeatedly to advance the display to the correct hour,
AM or PM.
7.) Press the MODE button again. The Minutes
display appears.
8.) Press the SET button repeatedly to advance the display to the correct minute.
9.) Press the MODE button once more, then press
the SET button. The clock begins to run.
Note: To see the date at any time, press the SET button. The display will
change from time to month/date for a few seconds and then change back to
time display automatically.
11
RP1103_010505.p65
11
5/1/2005, 11:49
Note: This radio includes a special circuit that will keep the clock running for
a certain time after the batteries are exhausted, even if the unit is not connected
to the AC outlet. However if you do not replace the batteries for a long period
of time the clock will stop running and will need to be reset after fresh batteries
are installed.
Display Light
To see the time in low-light conditions, press the LIGHT button. The display lighting
will turn on for a few seconds and then shut off automatically.
Earphone Jack
For private listening, an
PHONES jack is located on the left side of the radio.
Plug in the earphone (not included) and adjust the volume to a comfortable level.
The internal speaker is disconnected when the earphone is plugged into the radio.
12
RP1103_010505.p65
12
5/1/2005, 11:49
CARE AND MAINTENANCE
There are no user serviceable parts inside this radio. Please refer all service
problems to a qualified service facility.
If the cabinet becomes dusty, wipe the exterior with a soft dust cloth only. Never
use dusting sprays or polishes on the cabinet.
If the cabinet becomes dirty or smudged with fingerprints it may be wiped with a
soft cloth that has been slightly dampened with a mild soap and water solution.
Always disconnect the power cord from the AC outlet before cleaning, and never
allow any liquid to get inside the cabinet.
TO FIND THE LOCATION AND PHONE
NUMBER OF YOUR NEAREST SERVICE
R
CENTER PERMITTED TO PERFORM
WARRANTY...
SERVICE
CALL TOLL FREE: 1-800-695-0098
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE
PLEASE CALL:
1-800-898-9020
FOR CUSTOMER SERVICE, PLEASE WRITE TO:
Emerson Radio Corp.
Consumer Affairs Dept.
1901 Diplomat Drive,
Farmers Branch, TX 75234.
13
RP1103_010505.p65
13
5/1/2005, 11:49
LIMITED WARRANTY
Emerson Radio Corp. warrants manufacturing defects in original material, including
original parts and workmanship, under normal use and conditions, for a period of
ninety (90) days from the date of original purchase in the U.S. With your dated
proof of purchase, we will provide repair service at no charge for labor and parts
at an authorized Depot Repair Facility, or replace the product in our discretion.
For repair or replacement, pack your unit in a padded box, enclose your check or
money order payable to Emerson Radio Corp. in the amount of $5.00 (not required
by California residents) to cover shipping and handling costs, and enclose a copy
of your proof of purchase. Send your unit to:
Emerson Radio Corp.
1901 Diplomat Drive,
Farmers Branch, TX 75234.
This warranty does not cover damage from negligence, misuse, abuse, accident,
failure to follow operating instructions, commercial use, rental, repairs by an
unauthorized facility, or products purchased, used, serviced or damaged outside
of the United States.
THIS WARRANTYGIVES YOU SPECIFIC LEGAL RIGHTS, ANDYOU MAY
ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
AU898H
14
RP1103_010505.p65
14
5/1/2005, 11:49
EMERSON
Part No. 16-2979
501-01
Printed in China
RP1103_010505.p65
15
5/1/2005, 11:49
|