DT7&DR16 2.4G RC System User Manual
V1.00
Congratulations on purchasing your new DJI product. Please read this manual carefully to ensure you can get the
most out of it.
DR16 Receiver
DT7 Remote Controller
In the box
DT7 Remote Controller, DR16 Receiver, 3-Pin cable.
Required Items
4 AA batteries, Micro-USB cable, flight control system, multi-rotor etc.
DT7 Remote Controller
The DT7 remote controller is a wireless communication device using the 2.4GHz frequency band. It is only
compatible with the DR16 receiver.
[1
[2
[4
[6
[3]
[5]
J2
J3
J1
J4
[10]
[7
[8
[9
[12]
[11]
[1] Antenna
[2] Carrying Handle [3] 3-Position Switch S1
[4] 3-Position Switch S2
[5] Stick1 （J1;J2）
[6] Stick2（J3;J4） [7] Neck Strap Attachment
[8] Power Switch
[9] Power LED Indicator
[10] Slide Lever [11] Micro-USB Port
[12] Battery Compartment
©2013 DJI Innovations. All Rights Reserved.
- 1 -
Remote controller Power LED Indicator Status Information
Power LED Indicator
Sound
None
Remote Controller Status
Normal
B-B-B……
Low voltage (at 4V-4.3V). Replace the batteries immediately
Alarm will sound after 15 minutes without activity. It will stop once you
start using the remote controller.
B--B--B……
Important: The remote controller will power off automatically when battery voltage drops below 4V. Land and
change batteries as soon as possible when the low voltage alert occurs to avoid loss of control during flight.
Connecting the DR16 Receiver to the Flight Control System
The DR16 Receiver is designed to be used with the below flight control system. Connect the DR16 receiver to the
correct port on the main controller in the flight control system using a 3-Pin cable, then select the D-BUS receiver
type in the Assistant software.
Flight Control
NAZA-M Lite
X2
NAZA-M
X2
NAZA-M V2
X2
WooKong-M
X2
A2
X2
System
Port on the Main
Controller
Linking the DT7&DR16
1. Power on the main controller and the DR16 receiver.
2. Turn on the remote controller and place the remote controller 0.5m~1m from the receiver.
3. Poke the link button with a thin object and hold it until the LED indicator on the receiver blinks red, then release
it.
4. When the LED indicator becomes solid green, the link between the DT7 remote controller and the DR16 receiver
has been successfully established.
The LED Indicator Status of DR16
LED Indicator
Status
The remote controller is linked with the receiver successfully
The remote controller is turned off and there is no 2.4GHz signal around
The receiver is ready for linking
There is 2.4GHz signal around but the remote controller is not linked with the
receiver
Usages of the RC SYSTEM Assistant software
The RC SYSTEM assistant software is used to configure the DT7 remote controller, upgrade its firmware, select the
sticks mode and calibrate the sticks.
Download & Installation & Connection
1. Download the driver and RC SYSTEM Assistant software, then install the diver and software on your PC.
2. Turn on the remote controller and connect it to the PC by Micro-USB cable.
©2013 DJI Innovations. All Rights Reserved.
- 3 -
3. Run the RC SYSTEM Assistant software. Wait for the remote controller to connect to the Assistant software.
When the connection indicator is solid green
and the communication indicator blinks blue , it has connected.
Firmware Upgrade
1. On the [Info] page, click Latest version to download and install the upgrade following prompts.
2. Power cycle the remote controller after finishing the upgrade. Check the firmware version on the [Info] page, if
Assistant software shows the latest version, upgrade was successful.
Stick Mode Configuration
1. Select your custom control mode in the Stick Mode bar on the [Main] page.
2. Power cycle the remote controller, push both sticks and observe whether the cursors in the respective channels
are moving. This will confirm stick mode configuration.
Sticks Calibration
1. On the [Main] page, click the “Calibration” button to calibrate the sticks following prompts.
2. Calibrate the remote controller after every firmware upgrade or configuration, and calibrate on a regular basis.
DT7&DR16 Specifications
DJI DESSET 2.4G SYSTEM
Operating Frequency
Communication Distance（open area）
Remote Controller
General
2.4GHz ISM
1000m
2-stick, 7-channel
100mA@6V
Working Current
Battery Required
4 AA Batteries
DJI Receiver 16
General
2.4GHz D-BUS System
-97dBm
Receiving Sensitivity（1%PER）
Working Current
145mA@5V
Power Supply
4~8.4V
Size
41mmX29mmX5mm
Weight
10g
©2013 DJI Innovations. All Rights Reserved.
- 4 -
|