Dell™ XPS™ 710 Owner's Manual
Model DCDO
Notes, Notices, and Cautions
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
Abbreviations and Acronyms
®
®
If you purchased a Dell™ n Series computer, any references in this document to Microsoft Windows operating systems are not applicable.
Information in this document is subject to change without notice.
© 2006 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Dell XPS, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, and Dell OpenManage are
trademarks of Dell Inc.; Intel, Pentium, and Celeron are registered trademarks of Intel Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
October 2006 P/N XM141 Rev. A00
Bus type
PCI 32-bit
PCI Express x1 and x16
Bus speed
PCI: 33 MHz
PCI Express:
Bus throughput
x1 slot bidirectional speed — 2.5 Gbps
x16 slot bidirectional speed — 40 Gbps
PCI
connector
three
connector size
connector data width (maximum)
PCI Express
124 pins
32 bits
NOTE: If a graphics card is installed in each of the
PCI Express x16 card slots in the dual-graphics
configuration, the PCI Express x1 card slot is not
accessible for use.
connector
one x1
connector size
36 pins
connector data width (maximum)
1 PCI Express lane
PCI Express
connector
one x8
connector size
98 pins
connector data width (maximum)
4 PCI Express lanes
PCI Express
connector
two x16
connector size
164 pins
connector data width (maximum)
16 PCI Express lanes
Drives
Available devices
Serial ATA drive, floppy drive, memory devices,
DVD drive, DVD-RW drive, CD-RW/DVD combo
drive, and media card reader
Externally accessible:
two 3.5-inch drive bays
four 5.25-inch drive bays
Internally accessible:
four 3.5-inch drive bays for hard drives
Connectors
External connectors:
IEEE 1394
front and back-panel 6-pin serial connectors
RJ45 connector
Network adapter
PS/2 (keyboard and mouse)
two 6-pin mini-DIN
Serial
USB
9-pin connector
two front-panel, six back-panel, and two internal
USB 2.0–compliant connectors
System board connectors:
IDE drive
one 40-pin connector
six 7-pin connectors
34-pin connector
Serial ATA
Floppy drive
Fan
four 5-pin connectors
three 124-pin connectors
36-pin connector
PCI
PCI Express x1
PCI Express x8
PCI Express x16
98-pin connector
two 164-pin connectors
Controls and Lights
Power control
Power light
push button
green light — Blinking green in sleep state; solid
green for power-on state.
amber light — Blinking amber indicates a problem
with an installed device; solid amber indicates an
Hard-drive access light
green
Network activity light (front panel)
Link integrity light (on integrated network adapter)
solid green indicates network connection
green light — A good connection exists between a
10-Mbps network and the computer.
orange light — A good connection exists between a
100-Mbps network and the computer.
yellow light — A good connection exists between a 1-
GB (1000-Mbps) network and the computer.
off (no light) — The computer is not detecting a
physical connection to the network.
Activity light (on integrated network adapter)
yellow blinking light when there is activity on the
network; if there is not any network activity, the light
will be off
Diagnostic lights
Standby power light
front panel LEDs
AUXPWR on the system board
eight multi-colored LEDs provide illumination for the
front of the computer
NOTE: The color of the front panel LEDs can be
back panel LEDs
two multi-colored lights provide illumination for the
I/O panel on the back of the computer
NOTE: The color of the back panel LEDs can be
Power
DC power supply:
CAUTION: To reduce the risk of fire, electric shock,
or injury, do not overload an electrical outlet,
power strip, or convenience receptacle. The total
ampere rating of all products plugged into an
electrical outlet, power strip, or other receptacle
should not not exceed 80 percent of the branch
circuit rating.
Wattage
750 W or
1 KW
Heat dissipation
750 W: 2559 BTU/hr or
1 KW: 3412 BTU/hr
NOTE: Heat dissipation is calculated based upon the
power supply wattage rating.
Voltage (see the safety instructions located in
the Product Information Guide)
auto-sensing power supply—90 V to 265 V at 50/60
Hz
Backup battery
3-V CR2032 lithium coin cell
Physical
Height
Without stand
With stand
Width
55.5 cm (21.9 inches)
57.2 cm (22.5 inches)
Without stand
With stand
Depth
21.9 cm (8.6 inches)
35.6 cm (14.0 inches)
59.4 cm (23.4 inches)
Weight
Typical configuration
Maximum configuration
21.7 kg (47.8 lb)
25.6 kg (56.4 lb)
Environmental
Temperature:
Operating
10° to 35°C (50° to 95°F)
–40° to 65°C (–40° to 149°F)
20% to 80% (noncondensing)
Storage
Relative humidity
Maximum vibration:
Operating
0.25 G at 3 to 200 Hz at 0.5 octave/min
0.5 G at 3 to 200 Hz at 1 octave/min
Storage
Maximum shock:
Operating
bottom half-sine pulse with a change in velocity of 20
inches/sec (50.8 cm/sec)
Storage
27-G faired square wave with a velocity change of
200 inches/sec (508 cm/sec)
Altitude:
Operating
Storage
–15.2 to 3048 m (–50 to 10,000 ft)
–15.2 to 10,668 m (–50 to 35,000 ft)
System Setup
Overview
Use system setup as follows:
l
l
l
To change the system configuration information after you add, change, or remove any hardware in your computer
To set or change a user-selectable option such as the user password
To read the current amount of memory or set the type of hard drive installed
Before you use system setup, it is recommended that you write down the system setup screen information for future reference.
NOTICE: Do not change the settings in system setup unless you are an expert computer user. Certain changes can cause your computer to work
incorrectly.
Entering System Setup
1. Turn on (or restart) your computer.
2. When the DELL logo appears, press <F2> immediately.
NOTE: Keyboard failure may result when a key on the keyboard is held down for extended periods of time. To avoid possible keyboard failure,
press and release <F2> in even intervals until the system setup screen appears.
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop, then shut down your
computer and try again.
System Setup Screens
The system setup screen displays current or changeable configuration information for your computer. Information on the screen is divided into three areas: the
options list, the active options field, and key functions.
Options List — This field appears on the left side of
Options Field — This field appears on the right side
the system setup window. The field is a scrollable list of the system setup window and contains information
containing features that define the configuration of
your computer, including installed hardware, power
conservation, and security features.
about each option listed in the Options List. In this
field you can view information about your computer
and make changes to your current settings.
Scroll up and down the list with the up- and down-
arrow keys. As an option is highlighted, the Options
Field displays more information about that option
and the option's current and available settings.
Press the left- and right-arrow keys to highlight an
option. Press <Enter> to make that selection active
and return to the Options List.
NOTE: Not all settings listed in the Options Field are
changeable.
Key Functions — This field appears below the
Options Field and lists keys and their functions
within the active system setup field.
System Setup Options
NOTE: Depending on your computer and installed devices, the items listed in this section may not appear, or may not appear exactly as listed.
System
Processor Info
Identifies the processor type, clock speed, bus
speed, L2 cache, ID, and whether the processor is
multiple core capable, supports Hyper-Threading and
supports 64-bit technology.
Memory Info
Identifies the memory type, speed, and channel
mode (dual or single) by DIMM slot location.
PCI Info
Indicates the expansion card type by slot location.
Displays current date and time settings.
Date/Time
Boot Sequence
The computer attempts to boot from the sequence of
devices specified in this list.
NOTE: If you insert a boot device and restart the
computer, this option appears in the system setup
menu. To boot from a USB memory device, for
example, select the USB device and move it so that it
becomes the first device in the boot sequence.
Drives
Diskette Drive
Enables and disables the floppy drive attached to the
DSKT connector on the system board and sets read
permissions for the drive.
(Internal default)
l
l
l
Off — All floppy drives are disabled.
USB — USB floppy drives are enabled
Internal — The integrated floppy drive is
enabled.
Read Only — The integrated floppy drive is
enabled with read-only access.
l
NOTE: Operating systems with USB support will
recognize USB floppy drives regardless of this setting.
SATA Drives 0 through 5
Enables or disables drives attached to the SATA
connectors on the system board.
(On default)
l
l
l
Off — A device attached to the interface is not
usable.
On — A device attached to the interface is
usable.
RAID On - A device attached to the interface
PATA Drives 0 through 1
Enables or disables drives attached to the ATA
connectors on the system board, and lists the
controller details.
(On default)
l
l
Off — A device attached to the interface is not
usable.
On — A device attached to the interface is
usable.
SMART Reporting
Determines whether hard-drive errors for internal
drives are reported during system startup.
(Off default)
l
l
Off — Errors are not reported.
On — Errors are reported.
Onboard Devices
Integrated NIC
Enables or disables the integrated network interface
controller (NIC).
(On default)
l
l
l
Off — The integrated NIC is disabled.
On — The integrated NIC is enabled.
On w/PXE — The integrated NIC is on (with
PXE enabled).
NOTE: PXE is required only if you are booting to an
operating system located on another computer. If a
boot routine is not available from the remote system,
the computer attempts to boot from the next device
listed in the boot sequence.
Integrated Audio
Enables or disables the onboard audio controller.
(On default)
l
l
Off — Integrated audio is disabled.
On — Integrated audio is enabled.
USB Controller
Enables or disables the internal USB controller.
(On default)
l
l
l
Off — The USB controller is disabled.
On — The USB controller is enabled.
No Boot — The USB controller is enabled;
however, the BIOS will not recognize USB
storage devices.
NOTE: Operating systems with USB support will
recognize USB storage devices regardless of the No
Boot setting.
1394 Controller
Enables or disables the integrated IEEE 1394
controller.
(On default)
l
l
Off — The 1394 controller is disabled.
On — The 1394 controller is enabled.
Serial Port #1
Disables or selects the address for the integrated
serial port and determines how the serial port
operates.
(Auto default)
l
l
Off — The serial port is disabled.
Auto — The BIOS selects between COM1 and
COM3; if both resources are in use the port is
disabled.
l
l
COM1 — The port is configured at 3F8h with
IRQ 4.
COM3 — The port is configured at 3E8h with
IRQ 4.
PS/2 Mouse Port
Enables or disables the onboard PS/2-compatible
mouse controller.
(On default)
l
l
Off — The PS/2 legacy mouse port is disabled.
On — The PS/2 legacy mouse port is enabled.
LED color
Adjusts the color of the front and back LEDs (see
Performance
Multiple CPU Core
Specifies whether the processor has more than one
core enabled.
(On default)
l
l
Off — Multiple CPU core technology is
disabled.
On — Multiple CPU core technology is enabled.
NOTE: The performance of some applications may
improve with an additional core enabled.
CPU Clock Speed
Provides limited capability to adjust the CPU clock
speed so that the CPU operates at a different
frequency than that designated in the manufacturer's
design specifications.
NOTE: To enable overclocking, you first need to
enable the option in BIOS and then download an
application like NVIDA® nTune™ version 5.0 or
higher.
NOTE: Pressing <Alt><F> returns your system to the
factory defaults including RAID settings.
HDD Acoustic Mode
Determines the acoustic mode at which the hard
drive operates.
(Bypass default)
l
l
l
l
Bypass — Do nothing (needed for older
drives).
Quiet — The hard drive operates at its most
quiet setting.
Suggested — Allow the hard drive
manufacturer to select the mode.
Performance — The hard drive operates at its
maximum speed.
NOTE: Switching to performance mode may cause an
increase in noise produced by the drive, but does not
affect the drive's performance.
NOTE: Changing the acoustics setting does not alter
your hard drive image.
Security
Admin Password
Used to prohibit an unauthorized user from changing
any configuration settings in the system setup.
(Not Set default)
System Password
Used to prohibit an unauthorized user from booting
to the operating system.
(Not Set default)
Password Changes
This option locks the system password field with the
administrator (admin) password.
(Unlocked default)
NOTE: When the system password field is locked,
you can no longer disable password security by
pressing <Ctrl><Enter> when the computer starts.
Execute Disable
Enables or disables Execute Disable Memory
Protection technology.
(On default)
l
l
Off — Execute Disable Memory Protection
technology is disabled.
On — Execute Disable Memory Protection
technology is enabled.
Power Management
AC Recovery
Specifies how the computer will behave when AC
power is restored after an AC power loss.
(Off default)
l
l
l
Off — The system stays off after AC power is
restored.
On — The system powers on after AC power is
restored.
Last — The system returns to the previous
state after AC power is restored.
Auto Power On
Disables or selects when to automatically turn on the
computer.
(Off default)
l
l
Off — Do not use the Auto Power Time.
Everyday — Turn the computer on every day
at the time set in Auto Power Time.
Weekdays — Turn the computer on Monday
through Friday at the time set in Auto Power
l
Time.
NOTE: This feature does not work if you turn off your
computer using a power strip or surge protector.
Auto Power Time
Specifies the time to automatically turn on the
computer.
Change the time to automatically turn on the
computer by pressing the up- or down-arrow key to
increase or decrease the numbers, or type the
numbers in the appropriate time field.
NOTE: This feature does not work if you turn off your
computer using a power strip or surge protector.
Suspend Mode
Specifies the power management suspend mode.
(S3 default)
l
l
S1 — The computer resumes more quickly from
sleep mode.
S3 — The computer conserves more power
when not in use (system memory remains
active).
Maintenance
Service Tag
Displays the system service tag.
Load Defaults
This setting restores the computer's factory-installed
default settings.
l
l
Cancel — Do not restore factory-installed
default settings.
Continue — Restore factory-installed default
settings.
Event Log
Displays the system event log.
l
l
Mark all entries — Mark all event log entries
as read (R).
Clear log — Clear all event log entries.
NOTE: Once an event log entry is marked as read (R)
that entry cannot be marked as unread (U).
POST Behavior
Fastboot
Enables or disables the option to speed up the boot
process by skipping some compatibility tests.
(On default)
l
l
Off — Do not skip any steps in the boot
process.
On — Boot quickly.
Numlock Key
Enables or disables the numerical and mathematical
features of the rightmost bank of keys on the
keyboard.
(On default)
l
l
Off — Right keypad keys function as arrows.
On — Right keypad keys function as numbers.
POST Hotkeys
Specifies the function keys to display on the screen
when the computer starts.
(Setup & Boot Menu default)
l
l
l
l
Setup & Boot Menu — Display both messages
(F2=Setup and F12=Boot Menu).
Setup — Display the setup message only
(F2=Setup).
Boot Menu — Display the Quickboot message
only (F12=Boot Menu).
None — Neither message is displayed.
Keyboard Errors
(Report default)
Enables or disables keyboard error reporting when
the computer starts.
l
l
Report — Display any keyboard errors.
Do not report — Do not display any keyboard
errors.
Boot Sequence
This feature allows you to change the boot sequence for the bootable devices installed on your computer.
Option Settings
l
l
l
l
Diskette Drive — The computer attempts to boot from the floppy drive. If the floppy disk in the drive is not bootable, if no floppy disk is in the drive, or if
there is no floppy drive installed in the computer, the computer attempts to boot from the next bootable device in the boot sequence.
Hard Drive — The computer attempts to boot from the primary hard drive. If no operating system is on the drive, the computer attempts to boot from
the next bootable device in the boot sequence.
CD Drive — The computer attempts to boot from the CD drive. If no CD is in the drive, or if the CD has no operating system, the computer attempts to
boot from the next bootable device in the boot sequence.
USB Flash Device — Insert the memory device into a USB port and restart the computer. When F12 = Boot Menu appears in the upper-right corner of
the screen, press <F12>. The BIOS detects the device and adds the USB flash option to the boot menu.
NOTE: To boot to a USB device, the device must be bootable. To make sure that your device is bootable, check the device documentation.
NOTE: An error message is generated only after the computer attempts to boot from every device in the boot sequence and no operating system is
found.
Changing Boot Sequence for the Current Boot
You can use this feature, for example, to tell the computer to boot from the CD drive so that you can run the Dell Diagnostics on the Dell ResourceCD, but you
want the computer to boot from the hard drive when the diagnostic tests are complete. You can also use this feature to restart your computer to a USB device
such as a floppy drive, memory key, or CD-RW drive.
NOTE: If you are booting to a USB floppy drive, you must first set the floppy drive to OFF in system setup (see System Setup).
2. Turn on (or restart) your computer.
3. When the DELL logo appears, press <F12> immediately.
NOTE: Keyboard failure may result when a key on the keyboard is held down for extended periods of time. To avoid possible keyboard failure,
press and release <F12> in even intervals until the Boot Device Menu appears.
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft Windows desktop, then shut down your
computer and try again.
4. At the Boot Device Menu, use the up- and down-arrow keys or press the appropriate number on the keyboard to highlight the device that is to be used
for the current boot only, and then press <Enter>.
For example, if you are booting to a USB memory key, highlight USB Flash Device and press <Enter>.
NOTE: To boot to a USB device, the device must be bootable. To make sure that your device is bootable, check the device documentation.
Changing Boot Sequence for Future Boots
2. Use the arrow keys to highlight the Boot Sequence menu option and press <Enter> to access the menu.
NOTE: Write down your current boot sequence in case you want to restore it.
3. Press the up- and down-arrow keys to move through the list of devices.
4. Press the spacebar to enable or disable a device (enabled devices have a checkmark).
5. Press plus (+) or minus (–) to move a selected device up or down the list.
Clearing Forgotten Passwords
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: This process erases both the system and setup passwords
3. Locate the 2-pin password jumper (PASSWORD) on the system board (see System Board Components), then remove the jumper plug and set the plug
aside.
4. Close the computer cover.
5. Connect your keyboard and mouse, then connect your computer and monitor to electrical outlets and turn them on.
6. After the Microsoft® Windows® desktop appears on your computer, turn the computer off:
a. Click Start, then click Turn Off Computer.
b. In the Turn off computer window, click Turn off.
The computer performs a shutdown of the operating system, and then turns off.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
7. Disconnect the keyboard and mouse, then disconnect the computer and monitor from their electrical outlets.
8. Press the power button on the computer to ground the system board.
NOTICE: The password jumper plug must be reinstalled on the password jumper pins in order to enable the password feature.
10. Locate the 2-pin password jumper on the system board (see System Board Components), and then reinstall the jumper plug to enable the password
feature.
NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.
12. Connect your computer and devices to electrical outlets, and then turn them on.
NOTE: In system setup (see Entering System Setup), both system and administrator password options appear as Not Set. The password feature is
enabled but a password is not assigned.
Clearing CMOS Settings
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: This procedure does not clear or reset system and setup passwords.
3. Locate the password (PASSWORD) and CMOS (RTCRST) jumpers on the system board (see System Board Components).
4. Remove the password jumper plug, then place the plug on the CMOS jumper pins and wait approximately 5 seconds.
NOTICE: The password jumper plug must be reinstalled on the password jumper pins in order to enable the password feature.
5. Remove the jumper plug from the CMOS jumper pins, and then reinstall the plug on the password jumper pins to enable the password feature.
NOTICE: To connect a network cable, first plug the cable into the network wall jack and then plug it into the computer.
7. Connect your computer and devices to electrical outlets, and then turn them on.
Cleaning Your Computer
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Computer, Keyboard, and Monitor
CAUTION: Before you clean your computer, disconnect the computer from the electrical outlet. Clean your computer with a soft cloth dampened
with water. Do not use liquid or aerosol cleaners, which may contain flammable substances.
l
Use a vacuum cleaner with a brush attachment to gently remove dust from the slots and holes on your computer and from between the keys on the
keyboard.
NOTICE: Do not wipe the display screen with any soap or alcohol solution. Doing so may damage the antiglare coating.
l
l
To clean your monitor screen, lightly dampen a soft, clean cloth with water. If possible, use a special screen-cleaning tissue or solution suitable for the
monitor's antistatic coating.
Wipe the keyboard, computer, and plastic part of the monitor with a soft cleaning cloth moistened with water.
Do not soak the cloth or let water drip inside your computer or keyboard.
Mouse
If your screen cursor skips or moves abnormally, clean the mouse. To clean a non-optical mouse:
1. Turn the retainer ring on the underside of your mouse counterclockwise, and then remove the ball.
2. Wipe the ball with a clean, lint-free cloth.
3. Blow carefully into the ball cage to dislodge dust and lint.
4. If the rollers inside the ball cage are dirty, clean the rollers with a cotton swab moistened lightly with isopropyl alcohol.
5. Recenter the rollers in their channels if they are misaligned. Ensure that fluff from the swab is not left on the rollers.
6. Replace the ball and retainer ring, and turn the retainer ring clockwise until it clicks into place.
Floppy Drive
NOTICE: Do not attempt to clean drive heads with a swab. The heads may become misaligned and prevent the drive from operating.
Clean your floppy drive using a commercially available cleaning kit. These kits contain pretreated floppy disks to remove contaminants that accumulate during
normal operation.
CDs and DVDs
NOTICE: Always use compressed air to clean the lens in the CD/DVD drive, and follow the instructions that come with the compressed air. Never touch
the lens in the drive.
If you notice problems, such as skipping, with the playback quality of your CDs or DVDs, try cleaning the discs.
1. Hold the disc by its outer edge. You can also touch the inside edge of the center hole.
NOTICE: To prevent damaging the surface, do not wipe in a circular motion around the disc.
2. With a soft, lint-free cloth, gently wipe the bottom of the disc (the unlabeled side) in a straight line from the center to the outer edge of the disc.
For stubborn dirt, try using water or a diluted solution of water and mild soap. You can also purchase commercial products that clean discs and provide
some protection from dust, fingerprints, and scratches. Cleaning products for CDs are safe to use on DVDs.
Dell Hardware Warranty Support Policy (U.S. Only)
Technician-assisted support requires the cooperation and participation of the customer in the troubleshooting process and provides for restoration of the
operating system, software programs, and hardware drivers to the original default configuration as shipped from Dell, as well as the verification of appropriate
functionality of the computer and all Dell-installed hardware. In addition to this technician-assisted support, online support is available at support.dell.com.
Additional support options may be available for purchase.
1
Dell provides limited support for the computer and any "Dell-installed" software and peripherals . Support for third-party software and peripherals is provided
2
by the original manufacturer, including those purchased and/or installed through Dell Software and Peripherals, Readyware, and Custom Factory Integration .
1
Repair services are provided pursuant to the terms and conditions of your limited warranty and any optional support service contract purchased with the
computer.
2
All Dell-standard components included in a Custom Factory Integration (CFI) project are covered by the standard Dell limited warranty for your computer.
However, Dell also extends a parts replacement program to cover all nonstandard, third-party hardware components integrated through CFI for the duration
of the computer's service contract.
Definition of "Dell-Installed" Software and Peripherals
Dell-installed software includes the operating system and some of the software programs that are installed on the computer during the manufacturing process
®
(Microsoft Office, Norton Antivirus, and so on).
Dell-installed peripherals include any internal expansion cards, or Dell-branded module bay or PC Card accessories. In addition, any Dell-branded monitors,
keyboards, mice, speakers, microphones for telephonic modems, docking stations/port replicators, networking products, and all associated cabling are
included.
Definition of "Third-Party" Software and Peripherals
Third-party software and peripherals include any peripheral, accessory, or software program sold by Dell not under the Dell brand (printers, scanners,
cameras, games, and so on). Support for all third-party software and peripherals is provided by the original manufacturer of the product.
FCC Notices (U.S. Only)
Most Dell computer systems are classified by the Federal Communications Commission (FCC) as Class B digital devices. To determine which classification
applies to your computer system, examine all FCC registration labels located on the bottom, side, or back panel of your computer, on card-mounting brackets,
and on the cards themselves. If any one of the labels carries a Class A rating, your entire system is considered to be a Class A digital device. If all labels carry
an FCC Class B rating as distinguished by either an FCC ID number or the FCC logo, (
), your system is considered to be a Class B digital device.
Once you have determined your system's FCC classification, read the appropriate FCC notice. Note that FCC regulations provide that changes or modifications
not expressly approved by Dell could void your authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
Class A
This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause harmful
interference with radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case you will be
required to correct the interference at your own expense.
Class B
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the manufacturer's instruction manual, may cause interference with radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, you are encouraged to try to correct the interference by one or more of the following
measures:
l
l
l
l
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
FCC Identification Information
The following information is provided on the device or devices covered in this document in compliance with FCC regulations:
l
l
Product name: Dell™ XPS™ 710
Model number: DCDO
Company name:
Dell Inc.
One Dell Way
Round Rock, Texas 78682 USA
512-338-4400
Contacting Dell
To contact Dell electronically, you can access the following websites:
l
l
www.dell.com
support.dell.com (support)
For specific web addresses for your country, find the appropriate country section in the table below.
NOTE: Toll-free numbers are for use within the country for which they are listed.
NOTE: In certain countries, support specific to Dell™ XPS™ computers is available at a separate telephone number listed for participating countries. If
you do not see a telephone number listed that is specific for XPS computers, you may contact Dell through the support number listed and your call will be
routed appropriately.
When you need to contact Dell, use the electronic addresses, telephone numbers, and codes provided in the following table. If you need assistance in
determining which codes to use, contact a local or an international operator.
NOTE: The contact information provided was deemed correct at the time that this document went to print and is subject to change.
Area Codes,
Local Numbers, and
Toll-Free Numbers
Department Name or Service Area,
Website and E-Mail Address
Country (City)
International Access Code
Country Code
City Code
Website: www.dell.com.ai
Anguilla
E-mail: la-techsupport@dell.com
General Support
toll-free: 800-335-0031
Website: www.dell.com.ag
E-mail: la-techsupport@dell.com
General Support
Antigua and Barbuda
Aomen
1-800-805-5924
0800-105
Technical Support (Dell™ Dimension™, Dell Inspiron™, Dell OptiPlex™, Dell
Latitude™, and Dell Precision™)
Technical Support (servers and storage)
Website: www.dell.com.ar
0800-105
E-mail: la-techsupport@dell.com
Argentina (Buenos Aires)
E-mail for desktop and portable computers:
la-techsupport@dell.com
International Access Code:
00
E-mail for servers and EMC® storage products:
la_enterprise@dell.com
Country Code: 54
Customer Care
toll-free: 0-800-444-0730
toll-free: 0-800-444-0733
toll-free: 0-800-444-0724
0-810-444-3355
Technical Support
City Code: 11
Technical Support Services
Sales
Website: www.dell.com.aw
E-mail: la-techsupport@dell.com
General Support
Aruba
toll-free: 800-1578
Australia (Sydney)
Website: support.ap.dell.com
E-mail: support.ap.dell.com/contactus
Technical Support (XPS)
International Access Code:
0011
toll-free: 1300 790 877
Country Code: 61
General Support
13DELL-133355
City Code: 2
Website: support.euro.dell.com
E-mail: tech_support_central_europe@dell.com
Home/Small Business Sales
Home/Small Business Fax
0820 240 530 00
0820 240 530 49
0820 240 530 14
0820 240 530 16
0820 240 530 81
0820 240 530 17
0820 240 530 17
0820 240 530 00
Austria (Vienna)
International Access Code:
900
Home/Small Business Customer Care
Preferred Accounts/Corporate Customer Care
Support for XPS
Country Code: 43
City Code: 1
Home/Small Business Support for all other Dell computers
Preferred Accounts/Corporate Support
Switchboard
Website: www.dell.com.bs
E-mail: la-techsupport@dell.com
General Support
Bahamas
Barbados
toll-free: 1-866-874-3038
Website: www.dell.com/bb
E-mail: la-techsupport@dell.com
General Support
1-800-534-3142
Website: support.euro.dell.com
Tech Support for XPS
02 481 92 96
02 481 92 88
02 481 92 95
02 713 15 65
02 481 91 00
02 481 92 99
02 481 91 00
Belgium (Brussels)
Tech Support for all other Dell computers
Tech Support Fax
International Access Code:
00
Customer Care
Country Code: 32
Corporate Sales
City Code: 2
Fax
Switchboard
Website: www.dell.com/bm
E-mail: la-techsupport@dell.com
General Support
Bermuda
1-877-890-0751
Website: www.dell.com/bo
E-mail: la-techsupport@dell.com
General Support
Bolivia
Brazil
toll-free: 800-10-0238
Website: www.dell.com/br
E-mail: BR-TechSupport@dell.com
Customer Care and Tech Support
Technical Support Fax
International Access Code:
00
0800 90 3355
51 2104 5470
Country Code: 55
Customer Care Fax
51 2104 5480
City Code: 51
Sales
0800 722 3498
British Virgin Islands
General Support
toll-free: 1-866-278-6820
604 633 4966
Technical Support (Penang, Malaysia)
Customer Care (Penang, Malaysia)
Transaction Sales (Penang, Malaysia)
Online Order Status: www.dell.ca/ostatus
Website: support.ca.dell.com
AutoTech (automated Hardware and Warranty Support)
Customer Service (Home/Home Office)
Customer Service (small/med./large business, government)
Brunei
604 633 4888
Country Code: 673
604 633 4955
toll-free: 1-800-247-9362
toll-free: 1-800-847-4096
toll-free: 1-800-387-5757
Customer Service (printers, projectors, televisions, handhelds, digital jukebox, and
wireless)
toll-free: 1-800-847-4096
Canada (North York,
Ontario)
Hardware Warranty Phone Support (XPS)
toll-free: 1-866-398-8977
toll-free: 1-800-847-4096
toll-free: 1-800-387-5757
International Access Code:
011
Hardware Warranty Phone Support (Home/Home Office)
Hardware Warranty Phone Support (small/med./large business, government)
Hardware Warranty Phone Support (printers, projectors, televisions, handhelds,
digital jukebox, and wireless)
1-877-335-5767
Sales (Home Sales/Small Business)
Sales (med./large bus., government)
Spare Parts Sales & Extended Service Sales
E-mail: la-techsupport@dell.com
General Support
toll-free: 1-800-387-5752
toll-free: 1-800-387-5755
1 866 440 3355
Cayman Islands
1-877-262-5415
Chile (Santiago)
Country Code: 56
City Code: 2
Website: www.dell.com/cl
E-mail: la-techsupport@dell.com
Sales and Customer Support
toll-free: 1230-020-4823
Technical Support website: support.dell.com.cn
Technical Support E-mail: support.dell.com.cn/email
Customer Care E-mail: customer_cn@dell.com
Technical Support Fax
592 818 1350
toll-free: 800 858 0540
toll-free: 800 858 2969
toll-free: 800 858 0950
toll-free: 800 858 0960
toll-free: 800 858 2920
Technical Support (XPS)
Technical Support (Dimension and Inspiron)
Technical Support (OptiPlex, Latitude, and Dell Precision)
Technical Support (servers and storage)
Technical Support (projectors, PDAs, switches, routers, and so on)
Technical Support (printers)
Customer Care
toll-free: 800 858 2311
toll-free: 800 858 2060
592 818 1308
China (Xiamen)
Country Code: 86
City Code: 592
Customer Care Fax
Home and Small Business
toll-free: 800 858 2222
toll-free: 800 858 2557
toll-free: 800 858 2055
toll-free: 800 858 2628
toll-free: 800 858 2999
toll-free: 800 858 2955
toll-free: 800 858 2020
toll-free: 800 858 2669
toll-free: 800 858 2572
toll-free: 800 858 2355
toll-free: 800 858 2811
toll-free: 800 858 2621
Preferred Accounts Division
Large Corporate Accounts GCP
Large Corporate Accounts Key Accounts
Large Corporate Accounts North
Large Corporate Accounts North Government and Education
Large Corporate Accounts East
Large Corporate Accounts East Government and Education
Large Corporate Accounts Queue Team
Large Corporate Accounts South
Large Corporate Accounts West
Large Corporate Accounts Spare Parts
Website: www.dell.com/cl
E-mail: la-techsupport@dell.com
General Support
Colombia
01-800-915-4755
0800-012-0231
Website: www.dell.com/cr
E-mail: la-techsupport@dell.com
General Support
Costa Rica
Website: support.euro.dell.com
E-mail: czech_dell@dell.com
Technical Support
Czech Republic (Prague)
22537 2727
22537 2707
22537 2714
22537 2728
22537 2711
International Access Code:
00
Customer Care
Fax
Country Code: 420
Technical Fax
Switchboard
Website: support.euro.dell.com
Technical Support for XPS
7010 0074
7023 0182
7023 0184
3287 5505
3287 1200
Technical Support for all other Dell computers
Customer Care (Relational)
Home/Small Business Customer Care
Switchboard (Relational)
Denmark (Copenhagen)
International Access Code:
00
Country Code: 45
Switchboard Fax (Relational)
Switchboard (Home/Small Business)
Switchboard Fax (Home/Small Business)
Website: www.dell.com/dm
E-mail: la-techsupport@dell.com
General Support
3287 1201
3287 5000
3287 5001
Dominica
toll-free: 1-866-278-6821
Website: www.dell.com/do
E-mail: la-techsupport@dell.com
General Support
Dominican Republic
1-800-156-1588
Website: www.dell.com/ec
E-mail: la-techsupport@dell.com
General Support (calling from Quito)
General Support (calling from Guayaquil)
Website: www.dell.com/ec
E-mail: la-techsupport@dell.com
General Support
Ecuador
toll-free: 999-119-877-655-3355
toll-free: 1800-999-119-877-655-3355
El Salvador
800-6132
Website: support.euro.dell.com
E-mail: fi_support@dell.com
Technical Support
Finland (Helsinki)
0207 533 555
0207 533 538
0207 533 533
0207 533 540
0207 533 530
0207 533 533
0207 533 530
Customer Care
International Access Code:
990
Switchboard
Country Code: 358
Sales under 500 employees
Fax
City Code: 9
Sales over 500 employees
Fax
Website: support.euro.dell.com
Home and Small Business
Technical Support for XPS
Technical Support for all other Dell computers
Customer Care
0825 387 129
0825 387 270
0825 823 833
0825 004 700
04 99 75 40 00
0825 004 700
0825 004 701
04 99 75 40 01
France (Paris)
(Montpellier)
Switchboard
Switchboard (calls from outside of France)
Sales
International Access Code:
00
Fax
Country Code: 33
Fax (calls from outside of France)
Corporate
City Codes: (1) (4)
Technical Support
0825 004 719
0825 338 339
01 55 94 71 00
01 55 94 71 00
01 55 94 71 01
Customer Care
Switchboard
Sales
Fax
Website: support.euro.dell.com
E-mail: tech_support_central_europe@dell.com
Technical Support for XPS
Technical Support for all other Dell computers
Home/Small Business Customer Care
Global Segment Customer Care
Preferred Accounts Customer Care
Large Accounts Customer Care
Public Accounts Customer Care
Switchboard
069 9792 7222
069 9792-7200
0180-5-224400
069 9792-7320
069 9792-7320
069 9792-7320
069 9792-7320
069 9792-7000
Germany (Frankfurt)
International Access Code:
00
Country Code: 49
City Code: 69
Website: support.euro.dell.com
Technical Support
00800-44 14 95 18
00800-44 14 00 83
2108129810
Greece
Gold Service Technical Support
Switchboard
International Access Code:
00
Gold Service Switchboard
Sales
2108129811
Country Code: 30
2108129800
Fax
2108129812
E-mail: la-techsupport@dell.com
General Support
Grenada
Guatemala
Guyana
toll-free: 1-866-540-3355
1-800-999-0136
E-mail: la-techsupport@dell.com
General Support
E-mail: la-techsupport@dell.com
General Support
toll-free: 1-877-270-4609
Website: support.ap.dell.com
Technical Support E-mail: support.dell.com.cn/email
Technical Support (XPS)
00852-3416 6923
00852-2969 3188
00852-2969 3191
00852-2969 3196
00852-3416 0906
00852-3416 0910
00852-3416 0907
00852-3416 0908
00852-3416 0912
00852-2969 3105
Technical Support (Dimension and Inspiron)
Technical Support (OptiPlex, Latitude, and Dell Precision)
Technical Support (servers and storage)
Technical Support (projectors, PDAs, switches, routers, and so on)
Customer Care
Hong Kong
International Access Code:
001
Country Code: 852
Large Corporate Accounts
Global Customer Programs
Medium Business Division
Home and Small Business Division
Website: support.ap.dell.com
E-mail: india_support_desktop@dell.com
india_support_notebook@dell.com
india_support_Server@dell.com
0802 506 8033
Technical Support (XPS computers)
India
or toll-free: 1800 425 2066
1600338045
Technical Support (portables, desktops, servers, and storage)
and 1600448046
1600 33 8044
1600 33 8046
Sales (Large Corporate Accounts)
Sales (Home and Small Business)
Website: support.euro.dell.com
E-mail: dell_direct_support@dell.com
Sales
Ireland Sales
01 204 4444
1850 200 778
1850 200 778
Dell Outlet
Online Ordering HelpDesk
Customer Care
Ireland (Cherrywood)
Home User Customer Care
Small Business Customer Care
Corporate Customer Care
Technical Support
01 204 4014
01 204 4014
1850 200 982
International Access Code:
00
Country Code: 353
Technical Support for XPS computers only
Technical Support for all other Dell computers
General
1850 200 722
1850 543 543
City Code: 1
Fax/Sales Fax
01 204 0103
01 204 4444
Switchboard
U.K. Customer Care (dial within U.K. only)
Corporate Customer Care (dial within U.K. only)
U.K. Sales (dial within U.K. only)
Website: support.euro.dell.com
Home and Small Business
Technical Support
0870 906 0010
0870 907 4499
0870 907 4000
02 577 826 90
02 696 821 14
02 696 821 13
02 696 821 12
Italy (Milan)
Customer Care
Fax
International Access Code:
00
Switchboard
Country Code: 39
Corporate
Technical Support
02 577 826 90
02 577 825 55
02 575 035 30
02 577 821
City Code: 02
Customer Care
Fax
Switchboard
E-mail: la-techsupport@dell.com
General Support (dial from within Jamaica only)
Website: support.jp.dell.com
Jamaica
1-800-440-9205
Technical Support (XPS)
toll-free: 0120-937-786
Technical Support outside of Japan (XPS)
044-520-1235
XPS Customer Care (if ordered items are missing or have been damaged during
shipment)
044-556-4240
Technical Support (Dimension and Inspiron)
toll-free: 0120-198-226
81-44-520-1435
Technical Support outside of Japan (Dimension and Inspiron)
Technical Support (Dell Precision, OptiPlex, and Latitude)
Technical Support outside of Japan (Dell Precision, OptiPlex, and Latitude)
toll-free: 0120-198-433
81-44-556-3894
Technical Support (Dell PowerApp™, Dell PowerEdge™, Dell PowerConnect™, and
Dell PowerVault™)
Japan (Kawasaki)
toll-free: 0120-198-498
81-44-556-4162
Technical Support outside of Japan (PowerApp, PowerEdge, PowerConnect, and
PowerVault)
International Access Code:
001
Technical Support (projectors, PDAs, printers, routers)
Technical Support outside of Japan (projectors, PDAs, printers, routers)
Faxbox Service
toll-free: 0120-981-690
81-44-556-3468
044-556-3490
Country Code: 81
City Code: 44
24-Hour Automated Order Status Service
Customer Care
044-556-3801
044-556-4240
Business Sales Division (up to 400 employees)
Preferred Accounts Division Sales (over 400 employees)
044-556-1465
044-556-3433
Public Sales (government agencies, educational institutions, and medical
institutions)
044-556-5963
Global Segment Japan
044-556-3469
044-556-1760
044-556-4300
Individual User
Switchboard
E-mail: krsupport@dell.com
Korea (Seoul)
Support
toll-free: 080-200-3800
toll-free: 080-999-0283
toll-free: 080-200-3801
toll-free: 080-200-3600
2194-6202
Technical Support (XPS)
International Access Code:
001
Support (Dimension, PDA, Electronics, and Accessories)
Country Code: 82
Sales
Fax
City Code: 2
Switchboard
2194-6000
Customer Technical Support (Austin, Texas, U.S.A.)
Customer Service (Austin, Texas, U.S.A.)
Fax (Technical Support and Customer Service) (Austin, Texas, U.S.A.)
Sales (Austin, Texas, U.S.A.)
512 728-4093
512 728-3619
512 728-3883
Latin America
512 728-4397
512 728-4600
SalesFax (Austin, Texas, U.S.A.)
or 512 728-3772
Website: support.euro.dell.com
Luxembourg
Support
342 08 08 075
+32 (0)2 713 15 96
26 25 77 81
Home/Small Business Sales
International Access Code:
00
Corporate Sales
Customer Care
+32 (0)2 481 91 19
26 25 77 82
Country Code: 352
Fax
Technical Support
toll-free: 0800 105
34 160 910
Macao
Customer Service (Xiamen, China)
Transaction Sales (Xiamen, China)
Website: support.ap.dell.com
Country Code: 853
29 693 115
Technical Support (XPS)
toll-free: 1800 885 784
toll-free: 1 800 880 193
Malaysia (Penang)
Technical Support (Dell Precision, OptiPlex, and Latitude)
Technical Support (Dimension, Inspiron, and Electronics and Accessories)
Technical Support (PowerApp, PowerEdge, PowerConnect, and PowerVault)
Customer Care
International Access Code:
00
toll-free: 1 800 881 306
toll-free: 1800 881 386
Country Code: 60
toll-free: 1800 881 306 (option 6)
toll-free: 1 800 888 202
City Code: 4
Transaction Sales
Corporate Sales
toll-free: 1 800 888 213
E-mail: la-techsupport@dell.com
001-877-384-8979
Customer Technical Support
or 001-877-269-3383
Mexico
50-81-8800
Sales
International Access Code:
or 01-800-888-3355
001-877-384-8979
00
Country Code: 52
Customer Service
Main
or 001-877-269-3383
50-81-8800
or 01-800-888-3355
toll-free: 1-866-278-6822
001-800-882-1519
E-mail: la-techsupport@dell.com
General Support
Montserrat
E-mail: la-techsupport@dell.com
General Support
Netherlands Antilles
Website: support.euro.dell.com
Technical Support for XPS
Technical Support for all other Dell computers
Technical Support Fax
020 674 45 94
020 674 45 00
020 674 47 66
020 674 42 00
020 674 4325
020 674 55 00
020 674 50 00
020 674 47 75
020 674 47 50
020 674 50 00
020 674 47 50
Netherlands (Amsterdam)
Home/Small Business Customer Care
Relational Customer Care
Home/Small Business Sales
Relational Sales
International Access Code:
00
Country Code: 31
City Code: 20
Home/Small Business Sales Fax
Relational Sales Fax
Switchboard
Switchboard Fax
New Zealand
Website: support.ap.dell.com
E-mail: support.ap.dell.com/contactus
Technical Support (XPS)
International Access Code:
00
toll-free: 0800 335 540
General Support
0800 441 567
Country Code: 64
E-mail: la-techsupport@dell.com
General Support
Nicaragua
001-800-220-1377
Website: support.euro.dell.com
Technical Support for XPS
Technical Support for all other Dell products
Relational Customer Care
Home/Small Business Customer Care
Switchboard
815 35 043
671 16882
671 17575
23162298
671 16800
671 16865
Norway (Lysaker)
International Access Code:
00
Country Code: 47
Fax Switchboard
E-mail: la-techsupport@dell.com
General Support
Panama
Peru
011-800-507-1264
0800-50-669
E-mail: la-techsupport@dell.com
General Support
Website: support.euro.dell.com
E-mail: pl_support_tech@dell.com
Customer Service Phone
Customer Care
Poland (Warsaw)
57 95 700
57 95 999
57 95 999
57 95 806
57 95 998
57 95 999
International Access Code:
011
Sales
Country Code: 48
Customer Service Fax
Reception Desk Fax
City Code: 22
Switchboard
Portugal
Website: support.euro.dell.com
Technical Support
707200149
International Access Code:
00
Customer Care
800 300 413
800 300 410 or 800 300 411 or
800 300 412 or 21 422 07 10
Country Code: 351
Sales
Fax
21 424 01 12
E-mail: la-techsupport@dell.com
General Support
Puerto Rico
1-877-537-3355
Website: www.dell.com/kn
E-mail: la-techsupport@dell.com
General Support
St. Kitts and Nevis
toll-free: 1-866-540-3355
Website: www.dell.com/lc
E-mail: la-techsupport@dell.com
General Support
St. Lucia
toll-free: 1-866-464-4352
Website: www.dell.com/vc
E-mail: la-techsupport@dell.com
General Support
St. Vincent and the
Grenadines
toll-free: 1-866-464-4353
NOTE: The phone numbers in this section should be called from within Singapore
or Malaysia only.
Singapore (Singapore)
Website: support.ap.dell.com
Technical Support (XPS)
toll-free: 1800 394 7464
toll-free: 1 800 394 7430
International Access Code:
005
Technical Support (Dimension, Inspiron, and Electronics and Accessories)
Country Code: 65
Technical Support (OptiPlex, Latitude, and Dell Precision)
toll-free: 1 800 394 7488
Technical Support (PowerApp, PowerEdge, PowerConnect, and PowerVault)
toll-free: 1 800 394 7478
Customer Care
toll-free: 1 800 394 7430 (option 6)
toll-free: 1 800 394 7412
Transaction Sales
Corporate Sales
Website: support.euro.dell.com
E-mail: czech_dell@dell.com
Technical Support
Customer Care
toll-free: 1 800 394 7419
Slovakia (Prague)
02 5441 5727
420 22537 2707
02 5441 8328
02 5441 8328
02 5441 7585
International Access Code:
00
Fax
Country Code: 421
Tech Fax
Switchboard (Sales)
Website: support.euro.dell.com
E-mail: dell_za_support@dell.com
Gold Queue
South Africa
(Johannesburg)
011 709 7713
011 709 7710
011 709 7707
011 709 7700
011 706 0495
011 709 7700
International Access Code:
09/091
Technical Support
Customer Care
Sales
Country Code: 27
City Code: 11
Fax
Switchboard
Southeast Asian and Pacific
Countries
Technical Support, Customer Service, and Sales (Penang, Malaysia)
604 633 4810
Website: support.euro.dell.com
Home and Small Business
Technical Support
902 100 130
902 118 540
902 118 541
902 118 541
902 118 539
Customer Care
Spain (Madrid)
Sales
International Access Code:
00
Switchboard
Fax
Country Code: 34
Corporate
City Code: 91
Technical Support
902 100 130
902 115 236
91 722 92 00
91 722 95 83
Customer Care
Switchboard
Fax
Website: support.euro.dell.com
Technical Support for XPS
Technical Support for all other Dell products
Relational Customer Care
Home/Small Business Customer Care
Employee Purchase Program (EPP) Support
Technical Support Fax
0771 340 340
08 590 05 199
08 590 05 642
08 587 70 527
020 140 14 44
08 590 05 594
08 590 05 185
Sweden (Upplands Vasby)
International Access Code:
00
Country Code: 46
City Code: 8
Sales
Website: support.euro.dell.com
E-mail: Tech_support_central_Europe@dell.com
Technical Support for XPS
Technical Support (Home and Small Business) for all other Dell products
Technical Support (Corporate)
Switzerland (Geneva)
0848 33 88 57
0844 811 411
0844 822 844
International Access Code:
00
Country Code: 41
Customer Care (Home and Small Business)
Customer Care (Corporate)
Fax
0848 802 202
0848 821 721
022 799 01 90
022 799 01 01
City Code: 22
Switchboard
Website: support.ap.dell.com
E-mail: support.dell.com.cn/email
Technical Support (XPS)
toll-free: 0080 186 3085
toll-free: 0080 186 1011
toll-free: 0080 160 1256
Taiwan
Technical Support (OptiPlex, Latitude, Inspiron, Dimension, and Electronics and
Accessories)
International Access Code:
002
Technical Support (servers and storage)
Customer Care
toll-free: 0080 160 1250
Country Code: 886
(option 5)
Transaction Sales
toll-free: 0080 165 1228
Corporate Sales
toll-free: 0080 165 1227
Website: support.ap.dell.com
Technical Support (OptiPlex, Latitude, and Dell Precision)
Technical Support (PowerApp, PowerEdge, PowerConnect, and PowerVault)
toll-free: 1800 0060 07
Thailand
toll-free: 1800 0600 09
International Access Code:
001
toll-free: 1800 006 007
Customer Care
(option 7)
Country Code: 66
Corporate Sales
toll-free: 1800 006 009
Transaction Sales
toll-free: 1800 006 006
Website: www.dell.com/tt
Trinidad/Tobago
E-mail: la-techsupport@dell.com
General Support
toll-free: 1-888-799-5908
Website: www.dell.com/tc
Turks and Caicos Islands
E-mail: la-techsupport@dell.com
General Support
toll-free: 1-877-441-4735
Website: support.euro.dell.com
E-mail: dell_direct_support@dell.com
Customer Care website: support.euro.dell.com/uk/en/ECare/form/home.asp
Sales
Home and Small Business Sales
Corporate/Public Sector Sales
Customer Care
0870 907 4000
01344 860 456
Home and Small Business Customer Care
Corporate Customer Care
0870 906 0010
01344 373 185
0870 906 0010
01344 373 186
01344 373 193
01344 373 199
01344 373 194
U.K. (Bracknell)
International Access Code:
00
Preferred Accounts (500–5000 employees)
Global Accounts Customer Care
Central Government Customer Care
Local Government & Education Customer Care
Health Customer Care
Country Code: 44
City Code: 1344
Technical Support
Technical Support for XPS computers only
Technical Support (Corporate/Preferred Accounts/PCA [1000+ employees])
Technical Support for all other products
General
0870 366 4180
0870 908 0500
0870 353 0800
Home and Small Business Fax
Website: www.dell.com/uy
E-mail: la-techsupport@dell.com
General Support
0870 907 4006
Uruguay
toll-free: 000-413-598-2521
toll-free: 1-800-433-9014
toll-free: 1-800-247-9362
toll-free: 1-877-459-7298
Automated Order-Status Service
AutoTech (portable and desktop computers)
Hardware and Warranty Support (Dell TV, Printers, and Projectors) for
Relationship customers
Americas Consumer XPS Support
toll-free: 1-800-232-8544
toll-free: 1-800-624-9896
toll-free: 1-800-624-9897
toll-free: 1-800-695-8133
Consumer (Home and Home Office) Support for all other Dell products
Customer Service
Employee Purchase Program (EPP) Customers
Financial Services website:
www.dellfinancialservices.com
Financial Services (lease/loans)
toll-free: 1-877-577-3355
Financial Services (Dell Preferred Accounts [DPA])
Business
toll-free: 1-800-283-2210
U.S.A. (Austin, Texas)
Customer Service and Support
toll-free: 1-800-456-3355
toll-free: 1-800-695-8133
toll-free: 1-877-459-7298
International Access Code:
011
Employee Purchase Program (EPP) Customers
Support for printers, projectors, PDAs, and MP3 players
Public (government, education, and healthcare)
Customer Service and Support
Country Code: 1
toll-free: 1-800-456-3355
toll-free: 1-800-695-8133
toll-free: 1-800-289-3355
Employee Purchase Program (EPP) Customers
Dell Sales
or toll-free: 1-800-879-3355
toll-free: 1-888-798-7561
toll-free: 1-800-671-3355
toll-free: 1-800-357-3355
toll-free: 1-800-247-4618
toll-free: 1-800-727-8320
toll-free: 1-877-DELLTTY
Dell Outlet Store (Dell refurbished computers)
Software and Peripherals Sales
Spare Parts Sales
Extended Service and Warranty Sales
Fax
Dell Services for the Deaf, Hard-of-Hearing, or Speech-Impaired
(1-877-335-5889)
E-mail: la-techsupport@dell.com
General Support
U.S. Virgin Islands
Venezuela
toll-free: 1-877-702-4360
Website: www.dell.com/ve
E-mail: la-techsupport@dell.com
General Support
0800-100-4752
Dell™ XPS™ 710 Owner's Manual
Finding Information
NOTE: Some features or media may be optional and may not ship with your computer. Some features or media may not be available in certain countries.
NOTE: Additional information may ship with your computer.
What Are You Looking For?
Find It Here
l
l
l
l
A diagnostic program for my computer
Drivers for my computer
My device documentation
Desktop System Software (DSS)
Drivers and Utilities CD (ResourceCD)
Documentation and drivers are already installed on your computer.
You can use the Drivers and Utilities CD to reinstall drivers (see
Reinstalling Drivers), access your documentation or run the Dell
Readme files may also be included on your CD to provide last-minute
updates about technical changes to your computer or advanced
technical reference material for technicians and experienced users.
NOTE: Drivers and documentation updates can be found at
support.dell.com.
l
l
l
l
l
l
Warranty information
Terms and Conditions (U.S. only)
Safety instructions
Regulatory information
Ergonomics information
End User License Agreement
Dell™ Product Information Guide
l
How to set up my computer
Setup Diagram
l
l
Service Tag and Express Service Code
Microsoft® Windows® Product Key Label
Service Tag and Microsoft Windows Product Key
These labels are located on your computer.
l
Use the Service Tag to identify your computer when you use
support.dell.com or contact support.
Enter the Express Service Code to direct your call when
contacting support.
l
l
Solutions — Troubleshooting hints and tips, articles from technicians, online
courses, and frequently asked questions
Dell Support Website — support.dell.com
l
l
Community — Online discussion with other Dell customers
Upgrades — Upgrade information for components, such as the memory, hard
drive, and operating system
NOTE: Select your region or business segment to view the
appropriate support site.
l
l
l
Customer Care — Contact information, service call and order status, and
warranty and repair information
Service and Support — Service call status, support history, service contract,
and online discussions with support
Reference — Computer documentation, details on my computer configuration,
product specifications, and white papers
l
l
Downloads — Certified drivers, patches, and software updates
Desktop System Software (DSS)— If you reinstall the operating system on your
computer, you should also reinstall the DSS utility. DSS automatically detects
your computer and operating system and installs the updates appropriate for
your configuration, providing critical updates for your operating system and
support for Dell™ 3.5-inch USB floppy drives, Intel® Pentium® M processors,
optical drives, and USB devices. DSS is necessary for correct operation of your
Dell computer.
To download Desktop System Software:
1. Go to support.dell.com, select your business segment, and
then enter your Service Tag or product model.
2. Select Drivers & Downloads, and then click Go.
3. Select your operating system and language, and then search
for the keyword Desktop System Software.
NOTE: The support.dell.com user interface may vary depending on
your selections.
l
l
l
How to use Windows XP
How to work with programs and files
How to personalize my desktop
Windows Help and Support Center
1. Click Start® Help and Support.
2. Type a word or phrase that describes your problem, and then
click the arrow icon.
3. Click the topic that describes your problem.
4. Follow the instructions on the screen.
l
How to reinstall my operating system
Operating System CD
The operating system is already installed on your computer. To
reinstall your operating system, use the Operating System CD (see
After you reinstall the operating system, use the Drivers and Utilities
CD to reinstall drivers for the devices that came with your computer.
NOTE: The color of your Operating System CD varies according to the
operating system you ordered.
Glossary
Dell™ XPS™ 710 Owner's Manual
Terms in this Glossary are provided for informational purposes only and may or may not describe features included with your particular computer.
A
AC — alternating current — The form of electricity that powers your computer when you plug the AC adapter power cable in to an electrical outlet.
ACPI — advanced configuration and power interface — A power management specification that enables Microsoft® Windows® operating systems to put a
computer in standby or hibernate mode to conserve the amount of electrical power allocated to each device attached to the computer.
AGP — accelerated graphics port — A dedicated graphics port that allows system memory to be used for video-related tasks. AGP delivers a smooth, true-color
video image because of the faster interface between the video circuitry and the computer memory.
ALS — ambient light sensor.
antivirus software — A program designed to identify, quarantine, and/or delete viruses from your computer.
APR — advanced port replicator — A docking device that allows you to conveniently use an external monitor, keyboard, mouse, and other devices with your
portable computer.
ASF — alert standards format — A standard to define a mechanism for reporting hardware and software alerts to a management console. ASF is designed to
be platform- and operating system-independent.
B
backup — A copy of a program or data file on a floppy, CD, DVD, or hard drive. As a precaution, back up the data files from your hard drive regularly.
battery — A rechargeable internal power source used to operate portable computers when not connected to an AC adapter and an electrical outlet.
battery life span — The length of time (years) during which a portable computer battery is able to be depleted and recharged.
battery operating time — The length of time (minutes or hours) that a portable computer battery powers the computer.
BIOS — basic input/output system — A program (or utility) that serves as an interface between the computer hardware and the operating system. Unless you
understand what effect these settings have on the computer, do not change them. Also referred to as system setup.
bit — The smallest unit of data interpreted by your computer.
®
Bluetooth wireless technology — A wireless technology standard for short-range (9 m [29 feet]) networking devices that allows for enabled devices to
automatically recognize each other.
boot sequence — Specifies the order of the devices from which the computer attempts to boot.
bootable CD — A CD that you can use to start your computer. In case your hard drive is damaged or your computer has a virus, ensure that you always have
a bootable CD or floppy disk available. Your Drivers and Utilities or ResourceCD is a bootable CD.
bootable disk — A disk that you can use to start your computer. In case your hard drive is damaged or your computer has a virus, ensure that you always
have a bootable CD or floppy disk available.
bps — bits per second — The standard unit for measuring data transmission speed.
BTU — British thermal unit — A measurement of heat output.
bus — A communication pathway between the components in your computer.
bus speed — The speed, given in MHz, that indicates how fast a bus can transfer information.
byte — The basic data unit used by your computer. A byte is usually equal to 8 bits.
C
C — Celsius — A temperature measurement scale where 0° is the freezing point and 100° is the boiling point of water.
cache — A special high-speed storage mechanism which can be either a reserved section of main memory or an independent high-speed storage device. The
cache enhances the efficiency of many processor operations.
L1 cache — Primary cache stored inside the processor.
L2 cache — Secondary cache which can either be external to the processor or incorporated into the processor architecture.
carnet — An international customs document that facilitates temporary imports into foreign countries. Also known as a merchandise passport.
CD — compact disc — An optical form of storage media, typically used for audio and software programs.
CD drive — A drive that uses optical technology to read data from CDs.
CD player — The software used to play music CDs. The CD player displays a window with buttons that you use to play a CD.
CD-R — CD recordable — A recordable version of a CD. Data can be recorded only once onto a CD-R. Once recorded, the data cannot be erased or written
over.
CD-RW — CD rewritable — A rewritable version of a CD. Data can be written to a CD-RW disc, and then erased and written over (rewritten).
CD-RW drive — A drive that can read CDs and write to CD-RW (rewritable CDs) and CD-R (recordable CDs) discs. You can write to CD-RW discs multiple times,
but you can write to CD-R discs only once.
CD-RW/DVD drive — A drive, sometimes referred to as a combo drive, that can read CDs and DVDs and write to CD-RW (rewritable CDs) and CD-R
(recordable CDs) discs. You can write to CD-RW discs multiple times, but you can write to CD-R discs only once.
clock speed — The speed, given in MHz, that indicates how fast computer components that are connected to the system bus operate.
COA — Certificate of Authenticity — The Windows alpha-numeric code located on a sticker on your computer. Also referred to as the Product Key or
Product ID.
Control Panel — A Windows utility that allows you to modify operating system and hardware settings, such as display settings.
controller — A chip that controls the transfer of data between the processor and memory or between the processor and devices.
CRIMM — continuity rambus in-line memory module — A special module that has no memory chips and is used to fill unused RIMM slots.
cursor — The marker on a display or screen that shows where the next keyboard, touch pad, or mouse action will occur. It often is a blinking solid line, an
underline character, or a small arrow.
D
DDR SDRAM — double-data-rate SDRAM — A type of SDRAM that doubles the data burst cycle, improving system performance.
DDR2 SDRAM — double-data-rate 2 SDRAM — A type of DDR SDRAM that uses a 4-bit prefetch and other architectural changes to boost memory speed to over
400 MHz.
device — Hardware such as a disk drive, printer, or keyboard that is installed in or connected to your computer.
device driver — See driver.
DIN connector — A round, six-pin connector that conforms to DIN (Deutsche Industrie-Norm) standards; it is typically used to connect PS/2 keyboard or mouse
cable connectors.
disk striping — A technique for spreading data over multiple disk drives. Disk striping can speed up operations that retrieve data from disk storage.
Computers that use disk striping generally allow the user to select the data unit size or stripe width.
DMA — direct memory access — A channel that allows certain types of data transfer between RAM and a device to bypass the processor.
docking device — See APR.
DMTF — Distributed Management Task Force — A consortium of hardware and software companies who develop management standards for distributed
desktop, network, enterprise, and Internet environments.
domain — A group of computers, programs, and devices on a network that are administered as a unit with common rules and procedures for use by a specific
group of users. A user logs on to the domain to gain access to the resources.
DRAM — dynamic random-access memory — Memory that stores information in integrated circuits containing capacitors.
driver — Software that allows the operating system to control a device such as a printer. Many devices do not work properly if the correct driver is not
installed in the computer.
DSL — Digital Subscriber Line — A technology that provides a constant, high-speed Internet connection through an analog telephone line.
dual display mode — A display setting that allows you to use a second monitor as an extension of your display. Also referred to as extended display mode.
DVD — digital versatile disc — A high-capacity disc usually used to store movies. DVD drives read most CD media as well.
DVD drive — A drive that uses optical technology to read data from DVDs and CDs.
DVD player — The software used to watch DVD movies. The DVD player displays a window with buttons that you use to watch a movie.
DVD-R — DVD recordable — A recordable version of a DVD. Data can be recorded only once onto a DVD-R. Once recorded, the data cannot be erased or
written over.
DVD+RW — DVD rewritable — A rewritable version of a DVD. Data can be written to a DVD+RW disc, and then erased and written over (rewritten). (DVD+RW
technology is different from DVD-RW technology.)
DVD+RW drive — drive that can read DVDs and most CD media and write to DVD+RW (rewritable DVDs) discs.
DVI — digital video interface — A standard for digital transmission between a computer and a digital video display.
E
ECC — error checking and correction — A type of memory that includes special circuitry for testing the accuracy of data as it passes in and out of memory.
ECP — extended capabilities port — A parallel connector design that provides improved bidirectional data transmission. Similar to EPP, ECP uses direct memory
access to transfer data and often improves performance.
EIDE — enhanced integrated device electronics — An improved version of the IDE interface for hard drives and CD drives.
EMI — electromagnetic interference — Electrical interference caused by electromagnetic radiation.
ENERGY STAR® — Environmental Protection Agency requirements that decrease the overall consumption of electricity.
EPP — enhanced parallel port — A parallel connector design that provides bidirectional data transmission.
ESD — electrostatic discharge — A rapid discharge of static electricity. ESD can damage integrated circuits found in computer and communications equipment.
expansion card — A circuit board that installs in an expansion slot on the system board in some computers, expanding the capabilities of the computer.
Examples include video, modem, and sound cards.
expansion slot — A connector on the system board (in some computers) where you insert an expansion card, connecting it to the system bus.
ExpressCard — A removable I/O card adhering to the PCMCIA standard. Modems and network adapters are common types of ExpressCards. ExpressCards
support both the PCI Express and USB 2.0 standard.
Express Service Code — A numeric code located on a sticker on your Dell™ computer. Use the Express Service Code when contacting Dell for assistance.
Express Service Code service may not be available in some countries.
extended display mode — A display setting that allows you to use a second monitor as an extension of your display. Also referred to as dual display mode.
extended PC Card — A PC Card that extends beyond the edge of the PC Card slot when installed.
F
Fahrenheit — A temperature measurement scale where 32° is the freezing point and 212° is the boiling point of water.
FCC — Federal Communications Commission — A U.S. agency responsible for enforcing communications-related regulations that state how much radiation
computers and other electronic equipment can emit.
floppy — An electromagnetic form of storage media. Also known as a floppy diskette or a floppy disk.
floppy drive — A disk drive that can read and write to floppy disks.
folder — A term used to describe space on a disk or drive where files are organized and grouped. Files in a folder can be viewed and ordered in various ways,
such as alphabetically, by date, and by size.
format — The process that prepares a drive or disk for file storage. When a drive or disk is formatted, the existing information on it is lost.
FSB — front side bus — The data path and physical interface between the processor and RAM.
FTP — file transfer protocol — A standard Internet protocol used to exchange files between computers connected to the Internet.
G
G — gravity — A measurement of weight and force.
GB — gigabyte — A measurement of data storage that equals 1024 MB (1,073,741,824 bytes). When used to refer to hard drive storage, the term is often
rounded to 1,000,000,000 bytes.
GHz — gigahertz — A measurement of frequency that equals one thousand million Hz, or one thousand MHz. The speeds for computer processors, buses, and
interfaces are often measured in GHz.
graphics mode — A video mode that can be defined as x horizontal pixels by y vertical pixels by z colors. Graphics modes can display an unlimited variety of
shapes and fonts.
GUI — graphical user interface — Software that interacts with the user by means of menus, windows, and icons. Most programs that operate on the Windows
operating systems are GUIs.
H
hard drive — A drive that reads and writes data on a hard disk. The terms hard drive and hard disk are often used interchangeably.
heat sink — A metal plate on some processors that helps dissipate heat.
help file — A file that contains descriptive or instructional information about a product. Some help files are associated with a particular program, such as Help in
Microsoft Word. Other help files function as stand-alone reference sources. Help files typically have a filename extension of .hlp or .chm.
hibernate mode — A power management mode that saves everything in memory to a reserved space on the hard drive and then turns off the computer.
When you restart the computer, the memory information that was saved to the hard drive is automatically restored.
HTML — hypertext markup language — A set of codes inserted into an Internet web page intended for display on an Internet browser.
HTTP — hypertext transfer protocol — A protocol for exchanging files between computers connected to the Internet.
Hz — hertz — A unit of frequency measurement that equals 1 cycle per second. Computers and electronic devices are often measured in kilohertz (kHz),
megahertz (MHz), gigahertz (GHz), or terahertz (THz).
I
IC — integrated circuit — A semiconductor wafer, or chip, on which thousands or millions of tiny electronic components are fabricated for use in computer,
audio, and video equipment.
IDE — integrated device electronics — An interface for mass storage devices in which the controller is integrated into the hard drive or CD drive.
IEEE 1394 — Institute of Electrical and Electronics Engineers, Inc. — A high-performance serial bus used to connect IEEE 1394-compatible devices, such as
digital cameras and DVD players, to the computer.
infrared sensor — A port that allows you to transfer data between the computer and infrared-compatible devices without using a cable connection.
integrated — Usually refers to components that are physically located on the computer's system board. Also referred to as built-in.
I/O — input/output — An operation or device that enters and extracts data from your computer. Keyboards and printers are I/O devices.
I/O address — An address in RAM that is associated with a specific device (such as a serial connector, parallel connector, or expansion slot) and allows the
processor to communicate with that device.
IrDA — Infrared Data Association — The organization that creates international standards for infrared communications.
IRQ — interrupt request — An electronic pathway assigned to a specific device so that the device can communicate with the processor. Each device connection
must be assigned an IRQ. Although two devices can share the same IRQ assignment, you cannot operate both devices simultaneously.
ISP — Internet service provider — A company that allows you to access its host server to connect directly to the Internet, send and receive e-mail, and access
websites. The ISP typically provides you with a software package, user name, and access phone numbers for a fee.
K
Kb — kilobit — A unit of data that equals 1024 bits. A measurement of the capacity of memory integrated circuits.
KB — kilobyte — A unit of data that equals 1024 bytes but is often referred to as 1000 bytes.
key combination — A command requiring you to press multiple keys at the same time.
kHz — kilohertz — A measurement of frequency that equals 1000 Hz.
L
LAN — local area network — A computer network covering a small area. A LAN usually is confined to a building or a few nearby buildings. A LAN can be
connected to another LAN over any distance through telephone lines and radio waves to form a wide area network (WAN).
LCD — liquid crystal display — The technology used by portable computer and flat-panel displays.
LED — light-emitting diode — An electronic component that emits light to indicate the status of the computer.
local bus — A data bus that provides a fast throughput for devices to the processor.
LPT — line print terminal — The designation for a parallel connection to a printer or other parallel device.
M
Mb — megabit — A measurement of memory chip capacity that equals 1024 Kb.
Mbps — megabits per second — One million bits per second. This measurement is typically used for transmission speeds for networks and modems.
MB — megabyte — A measurement of data storage that equals 1,048,576 bytes. 1 MB equals 1024 KB. When used to refer to hard drive storage, the term is
often rounded to 1,000,000 bytes.
MB/sec — megabytes per second — One million bytes per second. This measurement is typically used for data transfer ratings.
memory — A temporary data storage area inside your computer. Because the data in memory is not permanent, it is recommended that you frequently save
your files while you are working on them, and always save your files before you shut down the computer. Your computer can contain several different forms of
memory, such as RAM, ROM, and video memory. Frequently, the word memory is used as a synonym for RAM.
memory address — A specific location where data is temporarily stored in RAM.
memory mapping — The process by which the computer assigns memory addresses to physical locations at start-up. Devices and software can then identify
information that the processor can access.
memory module — A small circuit board containing memory chips, which connects to the system board.
MHz — megahertz — A measure of frequency that equals 1 million cycles per second. The speeds for computer processors, buses, and interfaces are often
measured in MHz.
modem — A device that allows your computer to communicate with other computers over analog telephone lines. Three types of modems include: external, PC
Card, and internal. You typically use your modem to connect to the Internet and exchange e-mail.
module bay — A bay that supports devices such as optical drives, a second battery, or a Dell TravelLite™ module.
monitor — The high-resolution TV-like device that displays computer output.
mouse — A pointing device that controls the movement of the cursor on your screen. Typically you roll the mouse over a hard, flat surface to move the pointer
or cursor on your screen.
ms — millisecond — A measure of time that equals one thousandth of a second. Access times of storage devices are often measured in ms.
N
network adapter — A chip that provides network capabilities. A computer may include a network adapter on its system board, or it may contain a PC Card with
an adapter on it. A network adapter is also referred to as a NIC (network interface controller).
NIC — See network adapter.
notification area — The section of the Windows taskbar that contains icons for providing quick access to programs and computer functions, such as the clock,
volume control, and print status. Also referred to as system tray.
ns — nanosecond — A measure of time that equals one billionth of a second.
NVRAM — nonvolatile random access memory — A type of memory that stores data when the computer is turned off or loses its external power source. NVRAM
is used for maintaining computer configuration information such as date, time, and other system setup options that you can set.
O
optical drive — A drive that uses optical technology to read or write data from CDs, DVDs, or DVD+RWs. Example of optical drives include CD drives, DVD
drives, CD-RW drives, and CD-RW/DVD combo drives.
P
parallel connector — An I/O port often used to connect a parallel printer to your computer. Also referred to as an LPT port.
partition — A physical storage area on a hard drive that is assigned to one or more logical storage areas known as logical drives. Each partition can contain
multiple logical drives.
PC Card — A removable I/O card adhering to the PCMCIA standard. Modems and network adapters are common types of PC Cards.
PCI — peripheral component interconnect — PCI is a local bus that supports 32-and 64-bit data paths, providing a high-speed data path between the
processor and devices such as video, drives, and networks.
PCI Express — A modification to the PCI interface that boosts the data transfer rate between the processor and the devices attached to it. PCI Express can
transfer data at speeds from 250 MB/sec to 4 GB/sec. If the PCI Express chip set and the device are capable of different speeds, they will operate at the
slower speed.
PCMCIA — Personal Computer Memory Card International Association — The organization that establishes standards for PC Cards.
PIN — personal identification number — A sequence of numerals and/or letters used to restrict unauthorized access to computer networks and other secure
systems.
PIO — programmed input/output — A method of transferring data between two devices through the processor as part of the data path.
pixel — A single point on a display screen. Pixels are arranged in rows and columns to create an image. A video resolution, such as 800 x 600, is expressed as
the number of pixels across by the number of pixels up and down.
Plug-and-Play — The ability of the computer to automatically configure devices. Plug and Play provides automatic installation, configuration, and compatibility
with existing hardware if the BIOS, operating system, and all devices are Plug and Play compliant.
POST — power-on self-test — Diagnostics programs, loaded automatically by the BIOS, that perform basic tests on the major computer components, such as
memory, hard drives, and video. If no problems are detected during POST, the computer continues the start-up.
processor — A computer chip that interprets and executes program instructions. Sometimes the processor is referred to as the CPU (central processing unit).
program — Any software that processes data for you, including spreadsheet, word processor, database, and game packages. Programs require an operating
system to run.
PS/2 — personal system/2 — A type of connector for attaching a PS/2-compatible keyboard, mouse, or keypad.
PXE — pre-boot execution environment — A WfM (Wired for Management) standard that allows networked computers that do not have an operating system to
be configured and started remotely.
R
RAID — redundant array of independent disks — A method of providing data redundancy. Some common implementations of RAID include RAID 0, RAID 1,
RAID 5, RAID 10, and RAID 50.
RAM — random-access memory — The primary temporary storage area for program instructions and data. Any information stored in RAM is lost when you shut
down your computer.
readme file — A text file included with a software package or hardware product. Typically, readme files provide installation information and describe new
product enhancements or corrections that have not yet been documented.
read-only — Data and/or files you can view but cannot edit or delete. A file can have read-only status if:
¡
¡
It resides on a physically write-protected floppy disk, CD, or DVD.
It is located on a network in a directory and the system administrator has assigned rights only to specific individuals.
refresh rate — The frequency, measured in Hz, at which your screen's horizontal lines are recharged (sometimes also referred to as its vertical frequency). The
higher the refresh rate, the less video flicker can be seen by the human eye.
resolution — The sharpness and clarity of an image produced by a printer or displayed on a monitor. The higher the resolution, the sharper the image.
RFI — radio frequency interference — Interference that is generated at typical radio frequencies, in the range of 10 kHz to 100,000 MHz. Radio frequencies are
at the lower end of the electromagnetic frequency spectrum and are more likely to have interference than the higher frequency radiations, such as infrared
and light.
ROM — read-only memory — Memory that stores data and programs that cannot be deleted or written to by the computer. ROM, unlike RAM, retains its
contents after you shut down your computer. Some programs essential to the operation of your computer reside in ROM.
RPM — revolutions per minute — The number of rotations that occur per minute. Hard drive speed is often measured in rpm.
RTC — real time clock — Battery-powered clock on the system board that keeps the date and time after you shut down the computer.
RTCRST — real-time clock reset — A jumper on the system board of some computers that can often be used for troubleshooting problems.
S
ScanDisk — A Microsoft utility that checks files, folders, and the hard disk's surface for errors. ScanDisk often runs when you restart the computer after it has
stopped responding.
SDRAM — synchronous dynamic random-access memory — A type of DRAM that is synchronized with the optimal clock speed of the processor.
serial connector — An I/O port often used to connect devices such as a handheld digital device or digital camera to your computer.
Service Tag — A bar code label on your computer that identifies your computer when you access Dell Support at support.dell.com or when you call Dell for
customer service or technical support.
setup program — A program that is used to install and configure hardware and software. The setup.exe or install.exe program comes with most Windows
software packages. Setup program differs from system setup.
shortcut — An icon that provides quick access to frequently used programs, files, folders, and drives. When you place a shortcut on your Windows desktop
and double-click the icon, you can open its corresponding folder or file without having to find it first. Shortcut icons do not change the location of files. If you
delete a shortcut, the original file is not affected. Also, you can rename a shortcut icon.
shutdown — The process of closing windows and exiting programs, exiting the operating system, and turning off your computer. You can lose data if you turn
off your computer before completing a shutdown.
smart card — A card that is embedded with a processor and a memory chip. Smart cards can be used to authenticate a user on computers equipped for smart
cards.
software — Anything that can be stored electronically, such as computer files or programs.
S/PDIF — Sony/Philips Digital Interface — An audio transfer file format that allows the transfer of audio from one file to another without converting it to and
from an analog format, which could degrade the quality of the file.
standby mode — A power management mode that shuts down all unnecessary computer operations to save energy.
Strike Zone™ — Reinforced area of the platform base that protects the hard drive by acting as a dampening device when a computer experiences resonating
shock or is dropped (whether the computer is on or off).
surge protectors — Prevent voltage spikes, such as those that may occur during an electrical storm, from entering the computer through the electrical outlet.
Surge protectors do not protect against lightning strikes or against brownouts, which occur when the voltage drops more than 20 percent below the normal
AC-line voltage level.
Network connections cannot be protected by surge protectors. Always disconnect the network cable from the network connector during electrical storms.
SIM — Subscriber Identity Module. A SIM card contains a microchip that encrypts voice and data transmissions. SIM cards can be used in phones or portable
computers.
SVGA — super-video graphics array — A video standard for video cards and controllers. Typical SVGA resolutions are 800 x 600 and 1024 x 768.
The number of colors and resolution that a program displays depends on the capabilities of the monitor, the video controller and its drivers, and the amount of
video memory installed in the computer.
S-video TV-out — A connector used to attach a TV or digital audio device to the computer.
SXGA — super-extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 1024.
SXGA+ — super-extended graphics array plus — A video standard for video cards and controllers that supports resolutions up to 1400 x 1050.
system board — The main circuit board in your computer. Also known as the motherboard.
system setup — A utility that serves as an interface between the computer hardware and the operating system. System setup allows you to configure user-
selectable options in the BIOS, such as date and time or system password. Unless you understand what effect the settings have on the computer, do not
change the settings for this program.
system tray — See notification area.
T
TAPI — telephony application programming interface — Enables Windows programs to operate with a wide variety of telephony devices, including voice, data,
fax, and video.
text editor — A program used to create and edit files that contain only text; for example, Windows Notepad uses a text editor. Text editors do not usually
provide word wrap or formatting functionality (the option to underline, change fonts, and so on).
travel module — A plastic device designed to fit inside the module bay of a portable computer to reduce the weight of the computer.
U
UMA — unified memory allocation — System memory dynamically allocated to video.
UPS — uninterruptible power supply — A backup power source used when the electrical power fails or drops to an unacceptable voltage level. A UPS keeps a
computer running for a limited amount of time when there is no electrical power. UPS systems typically provide surge suppression and may also provide
voltage regulation. Small UPS systems provide battery power for a few minutes to enable you to shut down your computer.
USB — universal serial bus — A hardware interface for a low-speed device such as a USB-compatible keyboard, mouse, joystick, scanner, set of speakers,
printer, broadband devices (DSL and cable modems), imaging devices, or storage devices. Devices are plugged directly in to a 4-pin socket on your computer
or in to a multi-port hub that plugs in to your computer. USB devices can be connected and disconnected while the computer is turned on, and they can also be
daisy-chained together.
UTP — unshielded twisted pair — Describes a type of cable used in most telephone networks and some computer networks. Pairs of unshielded wires are
twisted to protect against electromagnetic interference, rather than relying on a metal sheath around each pair of wires to protect against interference.
UXGA — ultra extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1600 x 1200.
V
video controller — The circuitry on a video card or on the system board (in computers with an integrated video controller) that provides the video
capabilities—in combination with the monitor—for your computer.
video memory — Memory that consists of memory chips dedicated to video functions. Video memory is usually faster than system memory. The amount of
video memory installed primarily influences the number of colors that a program can display.
video mode — A mode that describes how text and graphics are displayed on a monitor. Graphics-based software, such as Windows operating systems,
displays in video modes that can be defined as x horizontal pixels by y vertical pixels by z colors. Character-based software, such as text editors, displays in
video modes that can be defined as x columns by y rows of characters.
video resolution — See resolution.
virus — A program that is designed to inconvenience you or to destroy data stored on your computer. A virus program moves from one computer to another
through an infected disk, software downloaded from the Internet, or e-mail attachments. When an infected program starts, its embedded virus also starts.
A common type of virus is a boot virus, which is stored in the boot sectors of a floppy disk. If the floppy disk is left in the drive when the computer is shut down
and then turned on, the computer is infected when it reads the boot sectors of the floppy disk expecting to find the operating system. If the computer is
infected, the boot virus may replicate itself onto all the floppy disks that are read or written in that computer until the virus is eradicated.
V — volt — The measurement of electric potential or electromotive force. One V appears across a resistance of 1 ohm when a current of 1 ampere flows
through that resistance.
W
W — watt — The measurement of electrical power. One W is 1 ampere of current flowing at 1 volt.
WHr — watt-hour — A unit of measure commonly used to indicate the approximate capacity of a battery. For example, a 66-WHr battery can supply 66 W of
power for 1 hour or 33 W for 2 hours.
wallpaper — The background pattern or picture on the Windows desktop. Change your wallpaper through the Windows Control Panel. You can also scan in
your favorite picture and make it wallpaper.
WLAN — wireless local area network. A series of interconnected computers that communicate with each other over the air waves using access points or
wireless routers to provide Internet access.
write-protected — Files or media that cannot be changed. Use write-protection when you want to protect data from being changed or destroyed. To write-
protect a 3.5-inch floppy disk, slide its write-protect tab to the open position.
WWAN — wireless wide area network. A wireless high-speed data network using cellular technology and covering a much larger geographic area than WLAN.
WXGA — wide-aspect extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1280 x 800."
X
XGA — extended graphics array — A video standard for video cards and controllers that supports resolutions up to 1024 x 768.
Z
ZIF — zero insertion force — A type of socket or connector that allows a computer chip to be installed or removed with no stress applied to either the chip or
its socket.
Zip — A popular data compression format. Files that have been compressed with the Zip format are called Zip files and usually have a filename extension
of .zip. A special kind of zipped file is a self-extracting file, which has a filename extension of .exe. You can unzip a self-extracting file by double-clicking it.
Zip drive — A high-capacity floppy drive developed by Iomega Corporation that uses 3.5-inch removable disks called Zip disks. Zip disks are slightly larger than
regular floppy disks, about twice as thick, and hold up to 100 MB of data.
Removing and Installing Parts
Dell™ XPS™ 710 Owner's Manual
Before You Begin
This chapter provides procedures for removing and installing the components in your computer. Unless otherwise noted, each procedure assumes that a
component can be replaced by performing the removal procedure in reverse order.
Recommended Tools
The procedures in this document may require one or more of the following tools:
l
l
l
Small flat-blade screwdriver
Phillips screwdriver
Flash BIOS update (see the Dell support website at support.dell.com)
Preparing to Work Inside Your Computer
Use the following safety guidelines to help protect your computer from potential damage and to help ensure your own personal safety.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: To reduce the risk of fire, electric shock, or injury, do not overload an electrical outlet, power strip, or convenience receptacle. The
total ampere rating of all products plugged into an electrical outlet, power strip, or other receptacle should not exceed 80 percent of the branch
circuit rating.
CAUTION: Your computer is heavy and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt the computer and
always lift correctly to avoid injury; avoid bending over while lifting.
NOTICE: Only a certified service technician should perform repairs on your computer. Damage due to servicing that is not authorized by Dell is not
covered by your warranty.
NOTICE: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface on the computer chassis.
NOTICE: Handle components and cards with care. Do not touch the components or contacts on a card. Instead, hold a card by its edges or by its metal
mounting bracket. Hold a component such as a microprocessor by its edges, not by its pins.
NOTICE: When disconnecting a cable, pull on the cable's connector or its strain-relief loop, not on the cable itself. Some cables have connectors with
locking tabs; before disconnecting this type of cable, press inward on the locking tabs to release the connector. When connecting or disconnecting a
cable, ensure that the connectors are correctly oriented and aligned to avoid damage to the connector and/or the connector's pins.
1. Ensure that the work surface is level and protected to prevent either the surface or the computer from being scratched.
NOTICE: To avoid losing data, save any work in progress and exit all open programs before turning off your computer.
2. Turn off the computer and all attached devices:
a. Click Start, then click Turn Off Computer.
b. In the Turn off computer window, click Turn off.
The computer performs a shutdown of the operating system, and then turns off.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
3. Disconnect the computer and all attached devices from their electrical outlets.
NOTICE: When disconnecting a network cable, first unplug the cable from your computer and then unplug it from the network port or device.
4. Disconnect all external cables from the computer.
5. Carefully, lift the rear of the computer and rotate the stabilizing feet into the closed position.
6. With the help of an assistant, carefully lay the computer down on a flat surface with the computer cover facing up.
Removing the Computer Cover
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.
NOTICE: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface on the computer chassis.
2. Pull back on the cover release latch.
NOTICE: Ensure that sufficient space exists to support the removed cover—at least 30 cm (1 ft) of desk top space.
1
4
computer cover
2
cover release latch
3
cover hinge tabs
stabilizing feet (closed)
3. With the cover release latch pulled back, grip the sides of the cover, then pivot the top of the cover up and away from the computer.
4. Slide the cover forward and up to remove it from the hinge slots, then set it aside in a secure and protected location.
Inside View of Your Computer
1
4
CD/DVD drive bays (4)
card fan
2
5
floppy drive/media card reader
front fan
3
hard drive bays (4)
System Board Components
1
white memory module
connectors (DIMM_1-2)
support memory modules or
memory module risers
2
black memory module
connectors (DIMM_3-4)
support memory modules
only when no memory
riser cards are installed;
otherwise these must be
left empty
3
hard drive fan
connector
(FAN_HDD)
4
7
IDE drive connector (IDE)
5
8
front I/O panel connector
(FRONTPANEL)
6
9
back LED connector
FlexBay connector (INT_USB)
main power connector
(POWER1)
SATA connectors
(SATA0-5)
10 front USB connector
(FRNT_USB)
11 front panel 1394
connector (FP1394)
12 PCI-Express x1
card slot (SLOT1)
NOTE: This slot is
not available in the
dual-graphics
configuration
13 PCI-Express x16 card slot
(SLOT2)
14 PCI card slot (SLOT3)
15 PCI-Express x16
card slot (SLOT4)
NOTE: This slot is not
available in the dual-
graphics configuration
16 PCI card slot (SLOT5)
17 PCI card slot (SLOT6)
20 battery socket (BATTERY)
23 floppy drive (DSKT)
18 PCI-Express x8
card slot (SLOT7)
19 RTC reset jumper (RTCRST)
22 power connector (POWER2)
21 password jumper
(PASSWORD)
24 card cage fan
connector
(FAN_CAGE)
25 processor fan connector
(FAN2_CPU)
26 primary processor (CPU)
27 processor fan
connector
(FAN1_CPU)
NOTICE: The FAN2_CPU
connector is not currently used
on this system and is reserved
for future use. Do not attach
the primary CPU fan to the
FAN2_CPU connector.
Memory
You can increase your computer memory by installing memory modules on the system board.
Your computer supports DDR2 memory. For additional information on the type of memory supported by your computer, see Memory.
DDR2 Memory Overview
l
DDR2 memory modules should be installed in pairs of matched memory size and speed. If the DDR2 memory modules are not installed in matched pairs,
the computer will continue to operate, but with a slight reduction in performance. See the label on the upper-right or upper-left corner of the module to
determine the module's capacity.
NOTE: Always install DDR2 memory modules in the order indicated on the system board.
The recommended memory configurations are:
¡
A pair of matched memory modules installed in DIMM connectors 1 and 2
or
¡
A pair of matched memory modules installed in DIMM connectors 1 and 2 and another matched pair installed in DIMM connectors 3 and 4
NOTICE: Do not install ECC memory modules.
l
l
If you install mixed pairs of PC2-4300 (DDR2 533-MHz) and PC2-5300 (DDR2 667-MHz) memory, the modules function at the speed of the slowest
module installed.
Be sure to install a single memory module in DIMM connector 1, the connector closest to the processor, before you install modules in any other
connector.
.
A
matched pair of modules in DIMM connectors 1 and 2 (white securing
clips)
B
matched pair of memory modules in DIMM connectors 3 and 4 (black securing
clips)
NOTICE: If you remove your original memory modules from the computer during a memory upgrade, keep them separate from any new modules that
you may have, even if you purchased the new modules from Dell. If possible, do not pair an original memory module with a new memory module.
Otherwise, your computer may not start properly. You should install your original memory modules in pairs either in DIMM connectors 1 and 2 or DIMM
connectors 3 and 4.
NOTE: Memory purchased from Dell is covered under your computer warranty.
Addressing Memory Configurations
®
®
If you are using a 32-bit operating system such as Microsoft Windows XP, your computer will support a maximum of 4 GB of memory. If you are using a 64-
bit operating system, your computer will support a maximum of 8 GB (2-GB DIMMs in each of the four slots) of memory.
Installing Memory
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface on the computer chassis.
3. Press out the securing clip at each end of the memory module connector.
1
memory connector closest to processor
2
securing clips (2)
3
memory connector
4. Align the notch on the bottom of the module with the crossbar in the connector.
1
4
cutouts (2)
crossbar
2
memory module
3
notch
NOTICE: To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the
module.
5. Insert the module into the connector until the module snaps into position.
If you insert the module correctly, the securing clips snap into the cutouts at each end of the module.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
7. Connect your computer and devices to electrical outlets, and turn them on.
8. When the message appears stating that memory size has changed, press <F1> to continue.
9. Log on to your computer.
10. Right-click the My Computer icon on your Windows desktop and click Properties.
11. Click the General tab.
12. To verify that the memory is installed correctly, check the amount of memory (RAM) listed.
Removing Memory
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface on the computer chassis.
2. Press out the securing clip at each end of the memory module connector.
3. Grasp the module and pull up.
If the module is difficult to remove, gently ease the module back and forth to remove it from the connector.
Cards
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Your Dell™ computer provides the following slots for PCI and PCI Express cards:
l
l
l
l
Three PCI card slots
Two PCI Express x16 card slots (can be used in a dual-graphics configuration)
One PCI Express x8 card slot
One PCI Express x1 card slot
NOTE: If a graphics card is installed in each of the PCI Express x16 card slots in the dual-graphics configuration, the PCI Express x1 and one PCI card
slot are not accessible for use.
1
4
7
PCI card
2
5
PCI Express x16 card
3
6
PCI Express x16 card slot
PCI Express x1 card
PCI Express x8 card
PCI Express x8 card slot
PCI Express x1 card slot
Removing PCI and PCI Express Cards
NOTICE: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface on the computer chassis.
NOTICE: If your computer came with a PCI graphics card installed, removal of the card is not necessary when installing additional graphics cards;
however, the card is required for troubleshooting purposes. If you remove the card, store it in a safe and secure location.
NOTICE: If you have the optional dual graphics card configuration, see Removing a PCI Express Graphics Card from a Dual Configuration to remove or
replace a graphics card.
3. Disconnect any cables connected to the card.
4. Press down the tab on the top of the card retainer at the appropriate card slot and pivot the card retainer back through the chassis wall.
5. If present, press the tab on the card retention device that lays over the installed cards and lift it to gain full access to the card.
1
4
release tab
fan bracket
2
card retainer
3
alignment guide
6. Press the release tab (if present) on the system board connector as you grasp the card by its top corners, and then ease the card out of the connector.
NOTE: If the card is full-length, press the release tab on the end of the alignment guides on the fan bracket.
1
PCI Express x16 card
2
securing tab
3
PCI Express x16 card slot
7. Install a filler bracket in the empty card-slot opening. If you are replacing the card, see Installing PCI and PCI Express Cards.
NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep
dust and dirt out of your computer.
NOTICE: Before rotating the card retainer back into place, ensure that the tops of all cards and filler brackets are flush with the alignment bar and the
notch in the top of each card or filler bracket fits around the alignment guide.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or
cause damage to the equipment.
8. Rotate the card retainer back into its original position; push its tip so that its tab clicks into place.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
9. If present, lower the card retention device that lays over the installed cards and snap it into place.
10. Replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on.
11. Uninstall the driver for the card that you removed.
NOTE: If you removed a sound card or a network adapter, see Network Adapter and Sound Card Settings.
Installing PCI and PCI Express Cards
NOTICE: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface on the computer chassis.
NOTICE: If your computer came with a PCI graphics card installed, removal of the card is not necessary when installing additional graphics cards;
however, the card is required for troubleshooting purposes. If you remove the card, store it in a safe and secure location.
NOTICE: If you have or are upgrading to the optional dual-graphics configuration, see Installing a PCI Express Graphics Card in a Dual Configuration to
install a graphics card.
3. If present, press the tab on the card retention device that lays over the installed cards and rotate it upwards to gain full access to the card.
4. Press down the tab on the top of the card retainer at the appropriate card slot and pivot the card retainer back through the chassis wall.
1
4
release tab
fan bracket
2
card retainer
3
alignment guide
5. Remove the filler bracket or existing card (see Removing PCI and PCI Express Cards) to create a card- slot opening.
6. Prepare the card for installation.
See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your
computer.
7. Position the card so that it is aligned with the slot and the securing tab (if present) is aligned with the securing slot.
NOTE: If the card is full-length, insert the card guide into the alignment slot on the fan bracket.
1
PCI Express x16 card
2
securing tab
3
PCI Express x16 card slot
NOTICE: Ensure that you release the securing tab to seat the card. If the card is not installed correctly, you may damage the system board.
8. Gently pull the securing tab (if present) and place the card in the connector. Press down firmly and ensure that the card is fully seated in the slot.
1
4
card connector (seated)
2
5
card connector (not
seated)
3
6
bracket properly aligned
within slot
bracket improperly aligned
outside of slot
alignment bar
alignment guide
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or
cause damage to the equipment.
NOTICE: An incorrectly attached graphics power cable may result in degraded graphics performance.
9. Connect any cables that should be attached to the card.
See the documentation for the card for information about the card's cable connections.
NOTICE: Before rotating the card retainer back into place, ensure that the tops of all cards and filler brackets are flush with the alignment bar and the
notch in the top of each card or filler bracket fits around the alignment guide.
10. Rotate the card retainer back into its original position; push its tip so that its tab clicks into place.
11. If present, lower the card retention device that lays over the installed cards and snap it into place.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
12. Replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on.
13. Install any drivers required for the card as described in the card documentation.
NOTE: If you installed a sound card or a network adapter, see Network Adapter and Sound Card Settings.
Removing a PCI Express Graphics Card from a Dual Configuration
NOTE: This section regards dual configurations of PCI Express x16 graphics cards only. For removal of any other type of PCI or PCI Express cards, see
3. If present, press the tab on the card retention device that lays over the installed cards and rotate it upwards to gain full access to the card.
4. Gently securing both graphics cards with one hand, remove the graphics card bridge (if present) with your other hand by pulling it up and away from the
computer. Set it aside.
1
graphics card bridge
2
power connectors (2)
3
dual-PCI Express graphics cards
5. Disconnect any cables connected to the card.
6. Press down the tab on the top of the card retainer at the appropriate card slot and pivot the card retainer back through the chassis wall.
1
4
release tab
fan bracket
2
card retainer
3
alignment guide
7. Press the release tab (if present) on the system board connector as you grasp the card by its top corners, and then ease the card out of the connector.
NOTE: If the card is full-length, press the release tab on the end of the alignment guides on the fan bracket.
1
PCI Express x16 card
2
securing tab
3
PCI Express x16 card slot
8. Install a filler bracket in the empty card-slot opening. If you are replacing the card, see Installing a PCI Express Graphics Card in a Dual Configuration.
NOTE: Installing filler brackets over empty card-slot openings is necessary to maintain FCC certification of the computer. The brackets also keep
dust and dirt out of your computer.
NOTE: The graphics card bridge (not present in all dual-graphics configurations) is not necessary in a single graphics card configuration.
NOTICE: Before rotating the card retainer back into place, ensure that the tops of all cards and filler brackets are flush with the alignment bar and the
notch in the top of each card or filler bracket fits around the alignment guide.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or
cause damage to the equipment.
9. Rotate the card retainer back into its original position; push its tip so that its tab clicks into place.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
10. If present, lower the card retention device that lays over the installed cards and snap it into place.
11. Replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on.
Installing a PCI Express Graphics Card in a Dual Configuration
NOTE: To upgrade to or downgrade from a dual-graphics configuration, you will need additional parts that can be ordered from Dell (see Contacting
This section pertains to dual PCI Express graphics card configurations only. For installation of other types of PCI or PCI Express cards, see Installing PCI and
The PCI Express x1 card slot is not available for use if a graphics card is installed in each of the PCI Express x16 card slots in a dual graphics card
configuration. If you are upgrading from a single graphics card to a dual-graphics card configuration, you will need to remove any card installed in the PCI
Express x1 card slot (see System Board Components to locate the PCI Express x1 card slot). To remove a PCI Express card, see Removing PCI and PCI
NOTICE: For information about upgrading your system to use NVIDIA SLI (Scalable Link Interface) dual-graphics technology, see the Dell website at
support.dell.com.
To learn more about NVIDIA SLI (Scalable Link Interface) dual-graphics technology, see Understanding Dual Graphics Technology.
3. If present, press the tab on the card retention device that lays over the installed cards and rotate it upwards to gain full access to the card.
4. Press down the tab on the top of the card retainer at the appropriate card slot and pivot the card retainer back through the chassis wall.
1
4
release tab
fan bracket
2
card retainer
3
alignment guide
5. Remove the filler bracket or existing graphics card (see Removing a PCI Express Graphics Card from a Dual Configuration) to create a card-slot opening.
NOTE: If you are upgrading to a dual graphics card configuration and have a card installed in the PCI Express x1 card slot, remove the card (see
6. Prepare the card for installation.
See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your
computer.
7. Position the card so that it is aligned with the slot and the securing tab (if present) is aligned with the securing slot.
NOTE: If the card is full-length, insert the card guide into the alignment slot on the fan bracket.
1
PCI Express x16 card
2
securing tab
3
PCI Express x16 card slot
NOTICE: Ensure that you release the securing tab to seat the card. If the card is not installed correctly, you may damage the system board.
8. Gently pull the securing tab (if present) and place the card in the connector. Press down firmly and ensure that the card is fully seated in the slot.
NOTICE: Do not route card cables over or behind the cards. Cables routed over the cards can prevent the computer cover from closing properly or
cause damage to the equipment.
NOTICE: An incorrectly attached graphics power cable may result in degraded graphics performance.
9. Connect any cables that should be attached to the card.
See the documentation for the card for information about the card's cable connections.
NOTICE: Before rotating the card retainer back into place, ensure that the tops of all cards and filler brackets are flush with the alignment bar and the
notch in the top of each card or filler bracket fits around the alignment guide.
10. Rotate the card retainer back into its original position; push its tip so that its tab clicks into place.
11. Attach the graphics card bridge (if required for your dual-graphics configuration), pressing firmly so that it completely covers the connector tabs.
1
graphics card bridge (not present on some
dual graphics card configurations)
2
power
connectors (2)
3
dual-PCI Express
graphics cards
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug the cable into the computer.
12. If present, lower the card retention device that lays over the installed cards and snap it into place.
13. Replace the computer cover (see Replacing the Computer Cover), reconnect the computer and devices to electrical outlets, and then turn them on.
Network Adapter and Sound Card Settings
If you installed a sound card:
1. Enter system setup (see Entering System Setup), select Integrated Audio Controller, and then change the setting to Off.
2. Connect external audio devices to the sound card connectors. Do not connect external audio devices to the microphone, speaker/headphone, or line-in
connectors on the back panel.
If you removed a sound card:
1. Enter system setup (see Entering System Setup), select Integrated Audio Controller, and then change the setting to On.
2. Connect external audio devices to the audio connectors on the back panel of the computer.
If you installed an add-in network adapter and want to disable the integrated network adapter:
1. Enter system setup (see Entering System Setup), select Integrated NIC Controller, and then change the setting to Off.
2. Connect the network cable to the add-in network adapter connectors. Do not connect the network cable to the integrated connector on the back panel.
If you removed an add-in network connector:
1. Enter system setup (see Entering System Setup), select Integrated NIC Controller, and then change the setting to On.
2. Connect the network cable to the integrated connector on the back panel of the computer.
Drives
Your computer supports:
l
l
l
l
Six SATA devices (hard drives or optical drives)
Two IDE devices (two hard drives or two optical drives)
One floppy drive
One Media Card Reader
NOTICE: When removing and replacing drives, be sure to leave the drive data and power cables connected to the system board.
NOTE: The 5.25-inch Media Card Reader/floppy drive carrier is not interchangeable with the hard drive carrier.
1
CD/DVD drive bays (4)
2
floppy drive/media card reader
3
hard-drive bays (4)
About Serial ATA Drives
Your computer supports up to four serial ATA hard drives and two serial ATA optical drives. Serial ATA drives provide the following benefits by transferring data
using serial technology and flexible cables that are thinner and longer than IDE cables:
l
l
Improved cable routing facilitates more efficient airflow inside the chassis.
Compact cable connectors save space on the system board and on the hard drive, allowing for more efficient utilization of space inside the chassis.
General Drive Installation Guidelines
SATA hard drives should be connected to connectors labeled "HDD" on the system board. Non-hard drive SATA devices should be attached to the connectors
labeled SATA, with the exception of a 5th SATA hard drive installed in a 5.25-inch drive bay, which much be connected to the SATA0 connector. IDE CD/DVD
drives should be connected to the connectors labeled "IDE."
When connecting a SATA cable, hold the cable by the connector at each end and press firmly into the connector. When disconnecting a SATA cable, hold the
cable by the connector at each end and pull until the connector detaches.
1
SATA data cable
2
SATA data connector (on the system board)
3
SATA drive
When you connect two IDE devices to a single IDE data cable and configure the devices for the cable select setting, the device attached to the last connector
on the data cable is primary or the boot device, and the device attached to the middle connector on the data cable is the secondary device. See the drive
documentation in your upgrade kit for information on configuring devices for the cable select setting.
To connect an IDE data cable, align the tab on one connector with the notch on the other. When disconnecting an IDE data cable, grasp the colored pull-tab
and pull until the connector detaches.
Hard Drive
Removing a Hard Drive
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover.
NOTICE: If you are replacing a hard drive that contains data that you want to keep, back up your files before you begin this procedure.
3. Disconnect the power cable and the data cable from the hard drive.
1
power cable
2
data cable
4. Press the blue tabs on each side of the hard-drive bracket toward each other and slide the drive up and out of the hard-drive bay.
1
blue tabs (2)
2
hard drive
3
hard drive bay
5. Ensure that all connectors are properly cabled and firmly seated.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
7. Connect the computer and devices to electrical outlets, and turn them on.
Installing a Hard Drive
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: If a hard-drive bracket is installed inside of the hard-drive bay, remove the bracket before you install the new hard drive.
4. Prepare the new hard drive for installation and check the documentation for the hard drive to verify that the drive is configured for your computer.
NOTE: If hard drive you are installing does not have the hard drive bracket attached, use your original hard drive bracket; snap the bracket onto
the new drive.
1
hard drive
2
hard drive bracket
5. Verify that the hard-drive bay is empty and unobstructed.
6. Slide the hard drive into the hard-drive bay until it clicks securely into place.
1
hard drive
2
hard drive bay
NOTICE: Ensure that all connectors are properly cabled and firmly seated.
7. Connect the power cable to the hard drive.
8. Connect the hard drive data cable to the hard drive.
1
power cable
2
data cable
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
10. Connect the computer and devices to electrical outlets, and turn them on.
See the documentation that came with the drive for instructions on installing any software required for drive operation.
Drive Panel
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Removing the Drive Panel
3. Grasp the drive release latch and slide it towards the base of the computer until the drive panel snaps open.
1
drive release latch
2
drive panel
3
drive panel tabs
4. Pivot the drive panel outward and lift it from its side hinges.
5. Set the drive panel aside in a secure location.
Replacing the Drive Panel
3. Align the drive panel tabs with the side-door hinges.
1
drive release latch
2
drive panel
3
drive panel tabs
4. Rotate the drive panel toward the computer until it snaps into place on the drive panel.
See the documentation that came with the drive for instructions on installing any software required for drive operation.
Floppy Drive
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Removing a Floppy Drive
4. Disconnect the power and data cables from the back of the floppy drive.
1
power cable
2
floppy drive data cable
5. Slide the drive release latch towards the base of the computer to release the shoulder screw, and then slide the drive out of the drive bay.
1
drive release latch
2
floppy drive
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
8. Connect the computer and devices to electrical outlets, and turn them on.
Installing a Floppy Drive
5. If no screws are attached to the new floppy drive, check the inside of the drive panel for shoulder screws. If screws are present, attach the screws to
the new drive.
1
floppy drive
2
shoulder screws (4)
Slide the floppy drive into the drive bay until it clicks into place.
1
drive release latch
2
floppy drive
6. Connect the power and data cables to the back of the floppy drive.
7. Check all cable connections and fold cables out of the way to avoid blocking airflow between the fan and cooling vents.
NOTICE: To connect a network cable, first plug the cable in to the network port or device and then plug it in to the computer.
10. Connect your computer and devices to their electrical outlets, and turn them on.
See the documentation that came with the drive for instructions on installing any software required for drive operation.
11. Enter system setup (see Entering System Setup), and select the appropriate Diskette Drive option.
Media Card Reader
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Removing a Media Card Reader
4. Disconnect the power and data cables from the back of the Media Card Reader.
1
media card reader power cable
2
system board connector
5. Slide the drive release latch towards the base of the computer to release the shoulder screw, and then slide the media card reader out of the drive bay.
1
drive release latch
2
media card reader
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
8. Connect the computer and devices to electrical outlets, and turn them on.
Installing a Media Card Reader
5. If no screws are attached to the Media Car d Reader, check the inside of the drive panel for shoulder screws. If screws are present, attach the screws
to the new card reader.
1
media card reader
2
shoulder screws (4)
6. Slide the Media Card Reader into the drive bay until it clicks into place.
1
drive release latch
2
media card reader
7. Attach the power and data cables to the back of the Media Card Reader.
8. Check all cable connections and fold cables out of the way to avoid blocking airflow between the fan and cooling vents.
NOTICE: To connect a network cable, first plug the cable in to the network port or device and then plug it in to the computer.
11. Connect your computer and devices to their electrical outlets, and turn them on.
See the documentation that came with the drive for instructions on installing any software required for drive operation.
12. Enter system setup (see Entering System Setup) and select the appropriate USB for FlexBay option.
CD/DVD Drive
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Removing a CD/DVD Drive
4. Disconnect the power and data cables from the back of the drive.
NOTE: If you are uninstalling your only CD/DVD drive and will not replace it at this time, disconnect the data cable from the system board and set
it aside.
1
data cable
2
power cable
5. Slide the drive release latch towards the base of the computer to release the shoulder screw, and then slide the CD/DVD drive out of the drive bay.
1
drive release latch
2
CD/DVD drive
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
8. Connect the computer and devices to electrical outlets, and turn them on.
Installing a CD/DVD Drive
5. Prepare the CD/DVD drive for installation and check the documentation that accompanied the drive to verify that the drive is configured for your
computer.
NOTE: If you are installing an IDE drive, configure the drive for the cable select setting.
6. If no screws are attached to the drive, check the inside of the drive panel for screws and, if screws are present, attach the screws to the new drive.
1
CD/DVD drive
2
shoulder screws (3)
7. Gently slide the drive into the drive bay until you hear a click or feel the drive securely installed.
1
drive release latch
2
CD/DVD drive
8. Attach the power and data cables to the CD/DVD drive.
1
power cable
2
data cable
9. Check all cable connections and fold cables out of the way to avoid blocking airflow between the fan and cooling vents.
NOTICE: To connect a network cable, first plug the cable in to the network port or device and then plug it in to the computer.
12. Connect your computer and devices to their electrical outlets, and turn them on.
See the documentation that came with the drive for instructions on installing any software required for drive operation.
Processor Airflow Shroud
CAUTION: Before you perform this procedure, follow the safety instructions located in the Product Information Guide.
Removing the Processor Airflow Shroud
CAUTION: The processor heat sink can get very hot during normal operation. Be sure that the heat sink has had sufficient time to cool before you
touch it.
3. Loose the two captive screws on the processor airflow shroud, and then rotate the shroud back, away from the fan.
1
processor airflow shroud
2
captive screws (2)
NOTICE: The processor heat sink is attached to the processor airflow shroud. When you remove the airflow shroud, lay it upside down or on its side to
avoid damaging the heatsink thermal interface.
4. Lift the processor airflow shroud out of the computer, and then set it aside.
Installing the Processor Airflow Shroud
3. Align the hinge slots on the processor airflow shroud with the hinge guides on the system board.
4. Gently rotate the processor airflow shroud towards the fan, and then tighten the two captive screws.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
6. Connect your computer and devices to electrical outlets, and turn them on.
Processor
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: Do not perform the following steps unless you are familiar with hardware removal and replacement. Performing these steps incorrectly could
damage your system board. For technical service, see Dell Hardware Warranty Support Policy (U.S. Only).
Removing the Processor
3. Disconnect the power cables from the POWER1 and POWER2 connectors (see System Board Components) on the system board.
5. Push down and out on the socket release lever.
6. Lift the socket release lever and open the processor cover.
1
4
processor cover
2
processor
3
socket
socket release lever
7. Remove the processor from the socket.
Leave the release lever extended in the release position so that the socket is ready for the new processor.
Installing the Processor
NOTICE: Ground yourself by touching an unpainted metal surface on the back of the computer.
1. Unpack the new processor.
NOTICE: You must position the processor correctly in the socket to avoid permanent damage to the processor and the computer when you turn on the
computer.
2. If the release lever on the socket is not fully extended, move it to that position.
3. Align the pin-1 corner of the processor and socket.
1
4
processor cover
2
5
processor
3
socket
socket release lever
socket pin-1 indicator
NOTICE: Socket pins are delicate. To avoid damage, ensure that the processor is aligned properly with the socket, and do not use excessive force
when you install the processor. Be careful not to touch or bend the pins on the system board.
4. Set the processor lightly in the socket and ensure that the processor is level in the socket. When the processor is positioned correctly, press it with
minimal pressure to seat it.
5. When the processor is fully seated in the socket, close the processor cover.
6. Pivot the socket release lever back toward the socket and snap it into place to secure the processor.
8. Reconnect the power cables to the POWER1 and POWER2 connectors (see System Board Components) on the system board.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
10. Connect your computer and devices to electrical outlets, and turn them on.
Battery
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Replacing the Battery
A coin-cell battery maintains computer configuration, date, and time information. The battery can last several years.
If you have to repeatedly reset time and date information after turning on the computer, replace the battery.
CAUTION: A new battery can explode if it is incorrectly installed. Replace the battery only with the same or equivalent type recommended by the
manufacturer. Discard used batteries according to the manufacturer's instructions.
To replace the battery:
1. Record all the screens in system setup (see System Setup) so that you can restore the correct settings after the new battery has been installed.
NOTICE: If you pry the battery out of its socket with a blunt object, be careful not to touch the system board with the object. Ensure that the object is
inserted between the battery and the socket before you attempt to pry out the battery. Otherwise, you may damage the system board by prying off
the socket or by breaking circuit traces on the system board.
5. Remove the battery by prying it out of its socket with your fingers.
6. Insert the new battery (CR2032) into the socket with the side labeled "+" facing up, and press the battery into place.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
8. Connect your computer and devices to electrical outlets, and turn them on.
10. Properly dispose of the old battery. See the Product Information Guide for battery disposal information.
Removing the Computer Stand
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: Your computer is heavy and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt the computer and
always lift correctly to avoid injury; avoid bending over while lifting.
CAUTION: The computer stand should be installed at all times to ensure maximum system stability. Failure to install the stand could result in the
computer tipping over, potentially resulting in bodily injury or damage to the computer.
2. Loosen the captive screw securing the stand to the base of the computer.
3. Gently slide the stand back, towards the rear of the computer, then pull the stand away from the computer to remove it.
1
computer stand
2
captive screw
Replacing the Computer Cover
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: Your computer is heavy and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt the computer and
always lift correctly to avoid injury; avoid bending over while lifting.
CAUTION: The computer stand should be installed at all times to ensure maximum system stability. Failure to install the stand could result in the
computer tipping over, potentially resulting in bodily injury or damage to the computer.
NOTICE: To avoid electrostatic discharge and damage to internal components, ground yourself by using a wrist grounding strap or by periodically
touching an unpainted metal surface on the computer chassis.
1. Ensure that all cables are connected, and fold cables out of the way.
2. Ensure that no tools or extra parts are left inside the computer.
3. Pivot the cover down and into position.
4. Press down on the cover until it clicks into place.
NOTE: The computer cover should easily snap into place; however, if necessary, pull back on the cover release latch until the cover is completely
closed, then slide the release latch forward to secure the cover.
1
computer cover
2
cover hinge tabs
3
hinge slots
5. Carefully, lift the rear of the computer and slide the stabilizing feet outward into the open position.
6. With the help of an assistant, carefully set the computer upright.
NOTICE: To connect a network cable, first plug the cable into the network port or device and then plug it into the computer.
7. Connect your computer and devices to electrical outlets, and turn them on.
Optimizing Performance
Dell™ XPS™ 710 Owner's Manual
Understanding PCI Express Cards
PCI Express is the next generation technology for graphics cards and PCI cards. The PCI Express x16 slot is used in place of the AGP graphics card slot. The
dimensions of PCI Express card slots are different from those of the PCI card slots, and the cards are not interchangeable (you cannot install a PCI card in a
PCI Express card slot, or a PCI Express card in a PCI card slot).
Some benefits of PCI Express technology include:
l
Greater available bandwidth — PCI Express bus bandwidth is 250 MB/s in each direction per lane simultaneously, while PCI bus bandwidth is 133 MB/s
in one direction at a time.
l
Prioritization of service — Multiple PCI cards installed in a computer all share a common bus, but each PCI Express card operates on its own channel.
Activities such as video conferencing and web camera functions can be automatically prioritized through the device software to reduce latency.
Understanding Dual Graphics Technology
With dual-graphics technology, an optional second PCI Express graphics card will significantly increase graphics performance on your computer. Benefits of this
technology can be seen in the improved portrayal of the 3-D graphics used in gaming and design applications.
Each graphics card includes at least one GPU (graphics processing unit). In dual graphics card configurations, multiple GPUs dynamically share their workload
to provide the best possible performance. For a given application, the software selects the optimum rendering (processing) mode.
For more information, see the documentation that came with your graphics card.
Understanding CPU Over-Clocking
NOTICE: Dell does not recommend operating the CPU at a frequency that is greater than the manufacturer's design specifications. Operating the CPU in
this manner may cause your system to shut down unexpectedly, may result in a loss of data, and may reduce the operational life of the processor. If
the system shuts down unexpectedly or is unstable, select a lower CPU operating frequency.
Your Dell computer provides the limited capability to adjust the operating frequency, or clock speed, of the processor.
Altering the CPU operating frequency (commonly referred to as over-clocking) enables you to increases the speed of the processor to a frequency that is faster
than the processor manufacturer's design specifications, and possibly enhance the overall performance of your system.
Dell does not guarantee that your computer will function or remain stable during the use of any extended operating frequencies. If your computer shuts down
unexpectedly or is unstable, select a lower operating frequency for the CPU.
You can make limited adjustments to the CPU operating frequency in system setup. For more information on accessing system setup, see System Setup.
Setting Up and Using Your Computer
Dell™ XPS™ 710 Owner's Manual
Front and Back View of the Computer
Front View
1
2
front I/O
connectors
3.5-inch drive
bays (2)
Can hold an optional Media Card Reader or floppy drive.
3- 5.25-inch drive Can hold a CD/DVD drive, or a SATA hard drive in a 5.25-inch drive bay
6
bays (4)
carrier.
NOTE: The hard-drive carrier is only for use in the 5.25-inch drive bays.
The floppy-drive/Media Card Reader and hard-drive carriers are not
interchangeable.
7
8
front panel
LEDs (4)
Multi-colored lights provide illumination for the front of the computer.
NOTE: The color of the front panel LEDs can be adjusted in system
CD/DVD drive
tray eject
Use to eject the drive tray of a CD/DVD drive.
button (4)
NOTE: The CD/DVD drive tray eject button is not a handle. The self-
tending doors open automatically when the eject button is pressed
and the drive tray is ejected.
9
front panel
LEDs (4)
Multi-colored lights provide illumination for the front of the computer.
NOTE: The color of the front panel LEDs can be adjusted in system
10 power button
Press to turn on the computer.
NOTICE: To avoid losing data, do not use the power button to
turn off the computer. Instead, perform an operating system
shutdown.
NOTE: The power button can also be used to wake the system or to
11 power light
The power light illuminates and blinks or remains solid to indicate
different states:
¡
¡
No light — The computer is turned off.
Steady green — The computer is in a normal operating
state.
¡
¡
Blinking green — The computer is in a power-saving state.
Steady amber — There may be a problem with an
Blinking amber — An internal power problem may exist
¡
12 computer stand Attach the computer stand to provide stability to the system.
CAUTION: The computer stand should be installed at all times
to ensure maximum system stability. Failure to install the
stand could result in the computer tipping over, potentially
resulting in bodily injury or damage to the computer.
Front I/O Connectors
1
2
3
4
microphone
connector
Use the microphone connector to attach a personal computer microphone
for voice or musical input into a sound or telephony program.
headphone
connector
Use the headphone connector to attach headphones.
diagnostic
lights (4)
Use the sequence of these diagnostics lights to help troubleshoot a
hard-drive
activity light
The hard drive light is on when the computer reads data from or writes
data to the hard drive. The light may also be on when a device such as
your CD player is operating.
5
6
network link
light
The network link light is on when a good connection exists between a
network and the computer.
USB 2.0
Use the front USB connectors for devices that you connect occasionally,
connectors (2) such as flash memory keys, cameras, or bootable USB devices. For more
It is recommended that you use the back USB connectors for devices that
typically remain connected, such as printers and keyboards.
7
IEEE 1394
connector
Use the IEEE 1394 connector for high-speed data devices such as digital
video cameras and external storage devices.
Back View
1
2
power connector Insert the power cable. The appearance of this connector may differ
from what is pictured.
back panel LEDs Multi-colored lights provide illumination for the I/O panel on the back of
(2)
the computer.
NOTE: The color of the back panel LEDs can be adjusted in system
3
4
back I/O
connectors
Plug serial, USB, and other devices into the appropriate connectors
card slots
Access connectors for any installed PCI or PCI Express cards.
NOTE: Some connector slots support full-length cards.
Back I/O Connectors
1
link integrity light
l
l
l
l
Green — A good connection exists between a 10-Mbps
network and the computer.
Orange — A good connection exists between a 100-Mbps
network and the computer.
Yellow — A good connection exists between a 1000-Mbps (1-
Gbps) network and the computer.
Off — The computer is not detecting a physical connection to
the network.
2
network adapter
connector
NOTICE: Do not plug a telephone cable into the network adapter
connector.
Use the network adapter connector to attach your computer to a
network or broadband device. Connect one end of a network cable
to either a network jack or your network or broadband device, and
then connect the other end of the network cable to the network
adapter connector on your computer. A click indicates that the
network cable has been securely attached.
On computers with an additional network connector card, use the
connectors on the card and on the back of the computer when
setting up multiple network connections (such as a separate intra-
and extranet).
NOTE: It is recommended that you use Category 5 wiring and
connectors for your network. If you must use Category 3 wiring,
force the network speed to 10 Mbps to ensure reliable operation.
3
4
network activity
light
Flashes a yellow light when the computer is transmitting or receiving
network data. A high volume of network traffic may make this light
appear to be in a steady "on" state.
keyboard
connector
Plug a standard PS/2 keyboard into the purple keyboard connector.
Turn off the computer and any attached devices before you connect
a keyboard to the computer. If you have a USB keyboard, plug it into
a USB connector.
5
mouse connector Plug a standard PS/2 mouse into the green mouse connector. Turn
off the computer and any attached devices before you connect a
mouse to the computer. If you have a USB mouse, plug it into a USB
connector.
6
7
side surround
sound connector
Use the (silver) side surround connector to attach additional
speakers.
center
subwoofer/LFE
connector
Use the (orange) subwoofer connector to attach a single subwoofer.
NOTE: The LFE (Low Frequency Effects) Audio channel, found in
digital surround sound audio schemes, carries only low frequency
information of 80 Hz and below. The LFE channel drives a subwoofer
to provide extremely low bass extension. Systems not using
subwoofers can shunt the LFE information to the main speakers in
the surround sound setup.
8
9
surround sound
connector
Use the (black) surround sound connector to attach multichannel-
capable speakers.
line-in connector
Use the (blue) line-in connector to attach a record/playback device
such as a cassette player, CD player, or VCR.
On computers with a sound card, use the connector on the card.
10 line-
out/headphone
Use the (green) line-out connector to attach headphones and
speakers with integrated amplifiers.
connector
On computers with a sound card, use the connector on the card.
11 microphone
connector
Use the (pink) microphone connector to attach a personal computer
microphone for voice or musical input into a sound or telephony
program.
12 S/PDIF connector Use the S/PDIF connector to transmit digital audio without going
through an analog audio conversion process.
13 serial connector
Connect a serial device, such as a handheld device, to the serial
port. If necessary, the address for this port can be modified through
14 USB 2.0
Use the back USB connectors for devices that typically remain
connected, such as printers and keyboards.
connectors (6)
NOTE: It is recommended that you use the front USB connectors for
devices that you connect occasionally, such as flash memory keys,
cameras, or bootable USB devices.
15 IEEE 1394
connector
Use the IEEE 1394 connector for high-speed data devices such as
digital video cameras and external storage devices.
Attaching the Computer Stand
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: Your computer is heavy and can be difficult to maneuver. Seek assistance before attempting to lift, move, or tilt the computer and
always lift correctly to avoid injury; avoid bending over while lifting.
CAUTION: The computer stand should be installed at all times to ensure maximum system stability. Failure to install the stand could result in the
computer tipping over, potentially resulting in bodily injury or damage to the computer.
2. Remove the thumb screw that is installed on the base of the computer.
NOTE: If the thumb screw is not already installed in the stand, it has been packaged separately.
3. Insert the six alignment tabs into the corresponding slots on the base of the computer, then slide the stand forward until all six tabs catch in the slots.
4. Ensure that the screw hole on the stand is aligned with the screw hole on the base of the computer.
5. Insert the captive screw into the screwhole, then tighten the screw to secure the stand to the base of the computer.
1
4
captive screw
slots (6)
2
stabilizing feet (closed)
3
computer stand
6. With the help of an assistant, carefully set the computer upright.
7. Carefully, lift the rear of the computer and slide the stabilizing feet outward into the open position.
Connecting Monitors
CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.
CAUTION: To reduce the risk of fire, electric shock, or injury, do not overload an electrical outlet, power strip, or convenience receptacle. The
total ampere rating of all products plugged into an electrical outlet, power strip, or other receptacle should not exceed 80 percent of the branch
circuit rating.
NOTE: Depending on the options selected when you purchased your computer, your video card may have two DVI ports, or one DVI and one VGA port.
1
DVI (white) connector
2
TV-OUT connector
3
VGA (blue) connector
Connecting a Monitor (Without an Adapter)
CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: If your monitor has a VGA connector and your computer does not have a VGA port, follow the instructions in Connecting a Monitor (With an
1. Turn off the computer and all attached devices:
a. Click Start, then click Turn Off Computer.
b. In the Turn off computer window, click Turn off.
The computer performs a shutdown of the operating system, and then turns off.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
2. Disconnect the computer and all attached devices from their electrical outlets.
3. Connect the DVI or VGA connector of your monitor to the appropriate connector on the back of the computer:
To connect a monitor with a DVI connector, use the (white) DVI port on your computer.
To connect a monitor with a VGA connector, use the (blue) VGA port on your computer.
Connecting a Monitor (With an Adapter)
CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: In order to connect a monitor with a VGA connector to the DVI port on the back of your computer, a DVI-to-VGA adapter is required.
1. Turn off the computer and all attached devices:
a. Click Start, then click Turn Off Computer.
b. In the Turn off computer window, click Turn off.
The computer performs a shutdown of the operating system, and then turns off.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
2. Disconnect the computer and all attached devices from their electrical outlets.
3. Connect the DVI-to-VGA adapter to the VGA connector on your monitor, and then connect the other end of the adapter to the (white) DVI port on the
back of the computer.
1
DVI (white) connector
2
DVI-to-VGA adapter (optional)
3
TV-OUT connector
Connecting a Monitor in a Dual Graphics Card Configuration
CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Dual graphics card configurations with multi-GPU technology enabled support only a single monitor. The monitor must be connected to the primary graphics
card in order to function.
NOTE: If your primary graphics card is equipped with two DVI ports and you are using a monitor with a VGA connector, a DVI-to-VGA adapter is required
1. Turn off the computer and all attached devices:
a. Click Start, then click Turn Off Computer.
b. In the Turn off computer window, click Turn off.
The computer performs a shutdown of the operating system, and then turns off.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
2. Disconnect the computer and all attached devices from their electrical outlets.
3. Connect the DVI or VGA connector of your monitor to the appropriate connector on the computer's primary graphics card:
To connect a monitor with a DVI connector, use the (white) DVI port on the primary graphics card.
To connect a monitor with a VGA connector, use the (blue) VGA port on the primary graphics card.
Connecting Two or More Monitors
CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: In order to connect and use two or more monitors in a dual graphics card configuration, multi-GPU technology must be disabled. To disable multi-
NOTE: Depending on the options selected when you purchased your computer, your video card may have two DVI ports, or one DVI and one VGA port.
1. Turn off the computer and all attached devices:
a. Click Start, then click Turn Off Computer.
b. In the Turn off computer window, click Turn off.
The computer performs a shutdown of the operating system, and then turns off.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
2. Disconnect the computer and all attached devices from their electrical outlets.
3. Connect two or more monitors to the appropriate DVI or VGA ports on the back of the computer.
NOTE: In order to connect a monitor with a VGA connector to the DVI port on the back of your computer, a DVI-to-VGA adapter is required.
To connect two or more monitors directly to the DVI or VGA ports on your computer, see Connecting a Monitor (Without an Adapter).
To connect the VGA connectors of one or more monitors to the DVI port(s) on your computer, see Connecting a Monitor (With an Adapter).
4. Change the display settings to support multiple monitors (see Changing the Display Settings to Support Two or More Monitors).
Connecting a TV
CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: If you are connecting a TV to your computer, you may connect only one monitor (VGA or DVI) in addition to the TV.
NOTE: See the documentation that came with your TV to ensure that you properly configure and connect the TV.
To connect a TV to your computer, an S-video cable is required. If you do not have an S-video cable, you may purchase one at most consumer electronics
stores. An S-video cable is not included with your computer.
1. Turn off the computer and all attached devices:
a. Click Start, then click Turn Off Computer.
b. In the Turn off computer window, click Turn off.
The computer performs a shutdown of the operating system, and then turns off.
NOTE: Ensure that the computer is off and not in a power management mode. If you cannot shut down the computer using the operating system,
press and hold the power button for 4 seconds.
2. Disconnect the computer and all attached devices from their electrical outlets.
3. Connect one end of the S-video cable to the TV-OUT connector on the back of the computer.
4. Connect the other end of the S-video cable to the S-video input connector on your TV.
Changing the Display Settings to Support Two or More Monitors
NOTE: Dual graphics card configurations with multi-GPU technology enabled support only a single monitor. In order to connect and use two or more
monitors in a dual graphics card configuration with multi-GPU technology, multi-GPU must be disabled.
1. With your monitors connected and turned on, turn on the computer.
The Microsoft® Windows® desktop displays on the primary monitor.
2. Disable multi-GPU technology in the display settings (applies only to dual graphics card configurations with multi-GPU technology enabled):
For information on disabling multi-GPU technology, see the documentation that came with your graphics card.
3. Enable clone mode or extended desktop mode in the display settings.
l
l
In clone mode, all monitors display the same image.
In extended desktop mode, you can drag objects from one screen to the other, increasing the amount of viewable work space.
For more information on changing the display settings for your graphics card, see the device user's guide in the Help and Support Center (click Start, click Help
and Support, click User and system guides, click Device guides, and then click the guide for your graphics card).
About Your RAID Configuration
NOTICE: In order to use the migrating option to convert a RAID configuration without losing data, your hard drive must initially be set up as a single
drive RAID 0 array before the operating system is loaded onto the drive (see Using the Nvidia MediaShield ROM Utility for instructions).
This section provides an overview of the RAID configuration you may have selected when you purchased your computer. There are several RAID configurations
available in the computer industry for different types of uses. Your Dell XPS computer supports RAID level 0 and RAID level 1. A RAID level 0 configuration is
recommended for high-performance programs while RAID level 1 is recommended for users that desire a high level of data integrity.
NOTE: RAID levels do not represent a hierarchy. A RAID level 1 configuration is not inherently better or worse than a RAID level 0 configuration.
The drives in a RAID configuration should be the same size in order to ensure that the larger drive does not contain unallocated (and therefore unusable)
space.
RAID Level 0 Configuration
NOTICE: Because a RAID level 0 configuration provides no data redundancy, a failure of one drive results in the loss of all data. To protect your data
when using a RAID level 0 configuration, perform regular backups.
RAID level 0 uses a storage technique known as data striping to provide a high data access rate. Data striping is a method of writing consecutive segments, or
stripes, of data sequentially across the physical drive(s) to create a large virtual drive. Data striping allows one of the drives to read data while the other drive
is searching for and reading the next block.
Another advantage of a RAID level 0 configuration is that it utilizes the full storage capacities of the drives. For example, two 120-GB hard drives combine to
provide 240 GB of hard drive space on which to store data.
NOTE: In a RAID level 0 configuration, the size of the configuration is equal to the size of the smallest drive multiplied by the number of drives in the
configuration.
RAID Level 1 Configuration
RAID level 1 uses a data-redundancy storage technique known as mirroring to enhance data integrity. When data is written to the primary drive, the data is
also duplicated, or mirrored, on the second drive in the configuration. A RAID level 1 configuration sacrifices high data-access rates for its data redundancy
advantages.
If a drive failure occurs, subsequent read and write operations are directed to the surviving drive. A replacement drive can then be rebuilt using the data from
the surviving drive.
NOTE: In a RAID level 1 configuration, the size of the configuration is equal to the size of the smallest drive in the configuration.
Configuring Your Hard Drives for RAID
Your computer can be configured for RAID, even if you did not select a RAID configuration when the computer was purchased. For an explanation of RAID levels
and their requirements, see About Your RAID Configuration. For information on how to install a hard drive, see Installing a Hard Drive.
You can use one of two methods to configure RAID hard drive volumes. The first method uses the Nvidia MediaShield ROM utility and is performed before you
install the operating system onto the hard drive. The second method uses Nvidia MediaShield and is performed after you have installed the operating system
and Nvidia RAID drivers.
Both methods require that you set your computer to RAID-enabled mode before you begin.
Setting Your Computer to RAID-Enabled Mode
2. Press the up- and down-arrow keys to highlight Drives, then press <Enter>.
3. Press the up- and down-arrow keys to highlight the applicable SATA drive, then press <Enter>.
4. Press the left- and right-arrow keys to highlight RAID On, and then press <Enter>. Repeat the process, as needed, for each SATA hard drive.
5. Press <Esc>, press the left- and right-arrow keys to highlight Save/Exit, and then press <Enter> to exit system setup and resume the boot process.
Using the Nvidia MediaShield ROM Utility
NOTICE: The following procedure will result in the loss of all data on your hard drive(s). Back up any data you want to keep before continuing.
NOTE: Do not use the following procedure to migrate an existing RAID configuration (see Converting From One RAID Configuration to Another RAID
Hard drives of any size may be used to create a RAID configuration. Ideally, however, the drives should be of equal size to avoid unallocated or unused space.
For an explanation of RAID levels and their requirements, see About Your RAID Configuration. For information on how to install a hard drive, see Installing a
1. Enable RAID for each applicable hard drive on your computer (see Setting Your Computer to RAID- Enabled Mode).
2. Restart the computer.
3. Press <Ctrl><N> when prompted to enter the RAID BIOS.
NOTE: If the operating system logo appears, continue to wait until you see the Microsoft Windows desktop, then shut down your computer and
try again.
The Define a New Array window appears.
4. Press <Tab> to navigate to the RAID Mode field.
To create a RAID 0 configuration, use the arrow keys to select Striping.
To create a RAID 1 configuration, use the arrow keys to select Mirroring.
5. Press <Tab> to navigate to the Free Disks field.
6. Use the up- and down-arrow keys to select a hard drive to include in the RAID array and then use the right-arrow key to move the selected drive from
the Free Disks field to the Array Disks field. Repeat for each disk you want to include in the RAID array.
NOTE: Your computer supports a maximum of two drives per RAID 1 array and four drives per RAID 0 array.
7. After assigning the hard drives to an array, press <F9>.
The Clear disk data prompt appears.
NOTICE: You will lose all data on the selected drives in the next step.
8. Press <Y> to clear all data from the selected drives.
The Array List window appears.
9. To review the details of the array that you set up, use the arrow keys to highlight the array in the Array Detail window and press <Enter>.
The Array Detail window appears.
NOTE: To delete an array, use the arrow keys to select the array and press <D>.
10. Press <Enter> to return to the previous screen.
11. Press <Ctrl><X> to exit the RAID BIOS.
Using Nvidia MediaShield
Nvidia MediaShield allows you to create, view, and manage RAID configurations.
NOTE: Use Nvidia MediaShield to create a RAID configuration only when you are adding one or more new hard drives to an existing (non-RAID) single-
drive computer, and you want to configure the new drive(s) into a RAID array.
Hard drives of any size may be used to create a RAID configuration using Nvidia MediaShield. Ideally, however, the drives should be of equal size to avoid
unallocated or unused space. For an explanation of RAID levels and their requirements, see About Your RAID Configuration.
Creating a RAID Array
NOTICE: The following procedure will result in the loss of all data on your hard drive(s). Back up any data you want to keep before continuing.
NOTE: Do not use the following procedure to migrate an existing RAID configuration (see Converting From One RAID Configuration to Another RAID
2. After rebooting your computer, launch Nvidia MediaShield.
3. Click Create under System Tasks.
The NVIDIA Create Array Wizard appears and lists the disks that are available for configuration.
4. Click Next.
5. Click Custom, then click Next.
6. Use the drop-down box to select Striping (RAID 0) or Mirroring (RAID 1).
7. Click Next.
The Free Disk Selection window appears.
NOTE: Only RAID-enabled hard drives are listed as free disks.
8. Click to select the drives that will make up the RAID configuration, click Next, and then click Next again.
NOTE: Your computer supports a maximum of two drives per RAID 1 array and four per RAID 0 array.
The Clearing System Data window appears.
NOTICE: The Clear System Data option deletes all data on the selected drive.
9. Click Next.
10. Click Finish to create the RAID configuration.
The MediaShield RAID management utility window appears and lists the array along with any other installed hard drives.
Deleting a RAID Array
NOTE: While this procedure deletes the RAID 1 volume, it also splits the RAID 1 volume into two non-RAID hard drives with a partition, and leaves any
existing data files intact. Deleting a RAID 0 volume, however, destroys all data on the volume.
NOTE: If your computer currently boots to RAID and you delete the RAID volume, your computer will become unbootable.
1. Launch Nvidia MediaShield.
2. Click to select the array you want to delete.
3. Click Delete Array in the System Tasks pane.
The NVIDIA Delete Array Wizard appears.
4. Click Next.
A confirmation screen appears with the name and size of the array that you have marked for deletion.
5. Click Finish to delete the RAID configuration.
The MediaShield RAID management utility window appears and lists any remaining arrays along with any other installed hard drives.
Converting From One RAID Configuration to Another RAID Configuration
NOTICE: In order to use the migrating option to convert a RAID configuration without losing data, your hard drive must initially be set up as a single
drive RAID 0 array before the operating system is loaded onto the drive (see Using the Nvidia MediaShield ROM Utility for instructions).
Nvidia MediaShield utilizes a one-step process known as migrating to change the current state of a disk or array without losing any data. If needed, additional
hard drives can be added to an existing array, including a single-drive RAID 0 configuration for conversion to a two-drive RAID 0 configuration; however, the
capacity of the resulting array must be equal to or greater than the size of the original configuration.
RAID 1 to RAID 1 conversions cannot be performed using the migrating process:
NOTICE: Additional hard drives to be used in the (migrated) array must be no smaller than any of the drives in the current configuration.
NOTE: Ensure that all drives to be used in the RAID configuration are RAID-enabled (see Setting Your Computer to RAID-Enabled Mode.)
1. Launch Nvidia MediaShield.
2. Click to select the array you want to convert.
3. Click Convert Array in the System Tasks pane.
The NVIDIA Convert Array Wizard appears.
4. Click Next.
5. Under RAID Mode Selection, select Mirroring or Striping from the drop-down menu.
6. Click Next.
NOTICE: You will lose all data on the selected drives in the next step.
7. Under Free Disk Selection, select the hard drive(s) you want to include in the (migrated) array by clicking the checkbox beside it.
8. Click Finish.
The MediaShield RAID management utility window appears and displays the status of the upgrade/migration process along with any other installed hard
drives.
NOTE: The time it takes to convert an array depends on several factors, such as the speed of the CPU, the type and size of the hard drive being
used, the operating system, etc.
Rebuilding a RAID Configuration
If one of the hard drives in a RAID array fails, you can rebuild the array by restoring the data to a replacement drive.
NOTE: Rebuilding an array can only be performed on RAID 1 and configurations.
1. Launch Nvidia MediaShield.
2. Click to select your RAID configuration (Mirroring) in the management utility window.
3. Select Rebuild Array in the System Tasks pane.
The NVIDIA Rebuild Array Wizard appears.
4. Click Next.
5. Select the hard drive you want to rebuild by clicking the checkbox beside it.
6. Click Next.
7. Click Finish.
The MediaShield RAID management utility window appears and displays the status of the rebuild process.
NOTE: You can use your computer while the computer is rebuilding the array.
NOTE: You can use any available (RAID-enabled) free disk to rebuild an array.
Playing CDs and DVDs
NOTICE: Do not press down on the CD or DVD tray when you open or close it. Keep the tray closed when you are not using the drive.
NOTICE: Do not move or tilt the computer when you are playing CDs or DVDs.
2. Place the disc, label side up, in the center of the drive tray.
3. Press the eject button or gently push on the tray to close it.
To format CDs for storing data, to create music CDs, or to copy CDs, see the CD software that came with your computer.
NOTE: Ensure that you observe all copyright laws when you create CDs or DVDs.
A CD player includes the following basic controls:
Play
Move backward within the current track
Pause
Move forward within the current track
Stop
Go to the previous track
Eject
Go to the next track
A DVD player includes the following basic controls:
Stop
Restart the current chapter
Play
Fast forward
Pause
Fast reverse
Advance a single frame while in pause mode
Go to the next title or chapter
Continuously play the current title or chapter
Go to the previous title or chapter
Eject
For more information on playing CDs or DVDs, click Help on the CD or DVD player (if available).
Adjusting the Volume
NOTE: When the speakers are muted, you do not hear the CD or DVD playing.
1. Click Start, point to All Programs® Accessories® Entertainment, and then click Volume Control.
2. In the Master Volume control window, click and drag the bar in the Master Volume column and slide it up or down to increase or decrease the volume.
For more information on volume control options, click Help in the Volume Control window.
Adjusting the Picture
If an error message notifies you that the current resolution and color depth are using too much memory and preventing DVD playback, adjust the display
properties.
1. Click Start, then click Control Panel.
2. Under Pick a category, click Appearance and Themes.
3. Under Pick a task..., click Change the screen resolution.
4. In the Display Properties window, click and drag the bar in Screen resolution to change the setting to 800 by 600 pixels.
5. Under Color quality, click the drop-down menu, and then click Medium (16 bit).
6. Click OK.
Copying CDs and DVDs
NOTE: Ensure that you observe all copyright laws when creating CDs or DVDs.
This section applies only to computers that have a CD-RW, DVD+/-RW, or CD-RW/DVD (combo) drive.
NOTE: The types of CD or DVD drives offered by Dell may vary by country.
The following instructions explain how to make an exact copy of a CD or DVD using Roxio Creator Plus - Dell Edition. You can also use Roxio Creator Plus for
other purposes, such as creating music CDs from audio files stored on your computer or backing up important data. For help, open Roxio Creator Plus, and
then click the question mark icon in the upper-right corner of the window.
How to Copy a CD or DVD
NOTE: CD-RW/DVD combo drives cannot write to DVD media. If you have a CD-RW/DVD combo drive and you experience recording problems, check for
available software patches on the Sonic support website at www.sonic.com.
The DVD-writable drives installed in Dell computers can write to and read DVD+/-R, DVD+/-RW and DVD+R DL (dual layer) media, but cannot write to and may
not read DVD-RAM or DVD-R DL media.
NOTE: Most commercial DVDs have copyright protection and cannot be copied using Roxio Creator Plus.
1. Click Start, point to All Programs® Roxio® Creator Projects, and then click RecordNow Copy.
2. Under the Copy tab, click Disc Copy.
3. To copy the CD or DVD:
l
If you have one CD/DVD drive, ensure that the settings are correct, and then click Disc Copy. The computer reads your source CD or DVD and
copies the data to a temporary folder on your computer hard drive.
When prompted, insert a blank CD or DVD into the drive and click OK.
l
If you have two CD/DVD drives, select the drive into which you have inserted your source CD or DVD, and then click Disc Copy. The computer
copies the data from the source CD or DVD to the blank CD or DVD.
Once you have finished copying the source CD or DVD, the CD or DVD that you have created automatically ejects.
Using Blank CDs and DVDs
CD-RW drives can write to CD recording media only (including high-speed CD-RW media) while DVD-writable drives can write to both CD and DVD recording
media.
Use blank CD-Rs to record music or permanently store data files. After the maximum storage capacity of a CD-R is reached, you cannot write to that CD-R again
(see the Sonic documentation for more information). Use blank CD-RWs if you plan to erase, rewrite, or update information on the CD later.
Blank DVD+/-Rs can be used to permanently store large amounts of data. After you create a DVD+/-R disc, you may not be able to write to that disc again if
the disc is finalized or closed during the final stage of the disc creation process. Use blank DVD+/-RWs if you plan to erase, rewrite, or update information on
the disc later.
CD-Writable Drives
Media Type Read Write Rewritable
CD-R
Yes
Yes
Yes
Yes
No
CD-RW
Yes
DVD-Writable Drives
Media Type Read Write Rewritable
CD-R
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
Yes
No
No
Yes
Yes
No
No
No
CD-RW
DVD+R
DVD-R
DVD+RW
DVD-RW
DVD+R DL
DVD-R DL
DVD-RAM
Maybe No
Maybe No
Helpful Tips
l
l
l
l
l
Use Microsoft® Windows® Explorer to drag and drop files to a CD-R or CD-RW only after you start Roxio Creator Plus and open a Creator project.
Use CD-Rs to burn music CDs that you want to play in regular stereos. CD-RWs may not play in many home or car stereos.
You cannot create audio DVDs with Roxio Creator Plus.
Music MP3 files can be played only on MP3 players or on computers that have MP3 software installed.
Commercially available DVD players used in home theater systems may not support all available DVD formats. For a list of formats supported by your
DVD player, see the documentation provided with your DVD player or contact the manufacturer.
l
l
l
Do not burn a blank CD-R or CD-RW to its maximum capacity; for example, do not copy a 650-MB file to a blank 650-MB CD. The CD-RW drive needs 1–2
MB of blank space to finalize the recording.
Use a blank CD-RW to practice CD recording until you are familiar with CD recording techniques. If you make a mistake, you can erase the data on the
CD-RW and try again. You can also use blank CD-RWs to test music file projects before you record the project permanently to a blank CD-R.
See the Sonic website at www.sonic.com for additional information.
Using a Media Card Reader (Optional)
CAUTION: Before you perform any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Use the media card reader to transfer data directly to your computer.
The media card reader supports the following memory types:
l
l
l
l
l
l
l
l
l
xD-Picture card
SmartMedia card (SMC)
CompactFlash card Type I and II (CF I/II)
MicroDrive card
SecureDigital card (SD)
MiniSD card
MultiMediaCard (MMC)
Reduced-size MultiMediaCard (RS-MMC)
Memory Stick (MS/MS Pro/MS Duo/MS Pro Duo)
1
4
xD-Picture card and
SmartMedia Card (SMC)
2
Memory Stick
(MS/MS Pro/MS
Duo/MS Pro Duo)
3
Secure Digital card
(SD/miniSD)/MultiMedia-Card
(MMC/RS-MMC)
CompactFlash card Type I
and II (CF I/II) and
MicroDrive card
1. Inspect the media card to determine the proper orientation for insertion.
2. Slide the media card into the appropriate slot of the media card reader until it is completely seated in the connector.
If you encounter resistance, remove the card, check for proper orientation, and then try again.
Network Setup Wizard
®
®
The Microsoft Windows XP operating system provides a Network Setup Wizard to guide you through the process of sharing files, printers, or an Internet
connection between computers in a home or small office.
1. Click Start, point to All Programs® Accessories® Communications, and then click Network Setup Wizard.
2. On the welcome screen, click Next.
3. Click Checklist for creating a network.
NOTE: Selecting the connection method This computer connects directly to the Internet enables the integrated firewall provided with Windows
XP SP1.
4. Complete the checklist and required preparations.
Return to the Network Setup Wizard and follow the instructions on the screen.
Transferring Information to a New Computer
®
®
The Microsoft Windows XP operating system provides a Files and Settings Transfer wizard to move data from one computer to a new computer. You can
move data such as:
l
l
l
l
E-mail
Toolbar settings
Window sizes
Internet bookmarks
The data can be transferred over a network or serial connection, or you can store it on a removable medium, such as a writable CD/DVD or floppy disk.
To prepare the new computer for the file transfer:
1. Click Start, point to All Programs® Accessories® System Tools, and then click Files and Settings Transfer Wizard.
The Files and Settings Transfer Wizard welcome screen appears.
2. Click Next.
3. On the Which computer is this? screen, click New Computer, and then click Next.
4. On the Do you have a Windows XP CD? screen, click I will use the wizard from the Windows XP CD, and then click Next.
5. When the Now go to your old computer screen appears, go to the source (old) computer that contains the data to be transferred. Do not click Next at
this time.
To copy data from the source computer:
1. On the source computer, insert the Windows XP Operating System CD.
2. On the Welcome to Microsoft Windows XP screen, click Perform additional tasks.
3. Under What do you want to do?, click Transfer files and settings.
4. On the Files and Settings Transfer Wizard welcome screen, click Next.
5. On the Which computer is this? screen, click Old Computer, and then click Next.
6. On the Select a transfer method screen, click the transfer method of your preference.
7. On the What do you want to transfer? screen, select the items you want to transfer, then click Next.
After the information has been copied, the Completing the Collection Phase screen appears.
8. Click Finish.
To transfer data to the new computer:
1. On the Now go to your old computer screen on the new computer, click Next.
2. On the Where are the files and settings? screen, select the method you chose for transferring your files and settings, and then click Next.
The wizard reads the collected files and settings and applies them to your new computer.
When all of the settings and files have been applied, the Finished screen appears.
3. Click Finished and restart the computer.
Power Management
Overview
The Microsoft® Windows® XP power management features can reduce the amount of electricity your computer uses when it is on and you are not using it.
You can reduce power to just the monitor or the hard drive, or you can use standby mode or hibernate mode to reduce power to the entire computer. When
the computer exits from a power conservation mode, it returns to the operating state it was in prior to entering the mode.
NOTE: Windows XP Professional includes security and networking features not available in Windows XP Home Edition. When a Windows XP Professional
computer is connected to a network, different options related to security and networking appear in certain windows.
NOTE: The procedures to activate the standby and hibernate modes may vary according to your operating system.
Standby Mode
Standby mode conserves power by turning off the display and the hard drive after a designated period of time, known as a time-out. When the computer exits
from standby mode, it computer returns to the operating state it was in prior to entering standby mode.
NOTICE: If your computer loses power while in standby mode, it may lose data.
To set standby mode to automatically activate after a defined period of inactivity:
1. Click Start, then click Control Panel.
2. Under Pick a category, click Performance and Maintenance.
3. Under or pick a Control Panel icon, click Power Options.
To immediately activate standby mode without a period of inactivity, click Start, click Turn Off Computer, and then click Stand by.
To exit from standby mode, press a key on the keyboard or move the mouse.
Hibernate Mode
Hibernate mode conserves power by copying system data to a reserved area on the hard drive, and then completely turning off the computer. When the
computer exits from hibernate mode, the desktop is restored to the state it was in prior to entering hibernate mode.
To activate hibernate mode:
1. Click Start, then click Control Panel.
2. Under Pick a category, click Performance and Maintenance.
3. Under or pick a Control Panel icon, click Power Options.
To exit from hibernate mode, press the power button. The computer may take a short time to exit from hibernate mode. Because the keyboard and mouse do
not function in hibernate mode, pressing a key on the keyboard or moving the mouse does not bring the computer out of hibernation.
Because hibernate mode requires a special file on your hard drive with enough disk space to store the contents of the computer memory, Dell creates an
appropriately sized hibernate mode file before shipping the computer to you. If the computer's hard drive becomes corrupted, Windows XP recreates the
hibernate file automatically.
Power Options Properties
Define your standby mode settings, hibernate mode settings, and other power settings in the Power Options Properties window. To access the Power
Options Properties window:
1. Click Start, then click Control Panel.
2. Under Pick a category, click Performance and Maintenance.
3. Under or pick a Control Panel icon, click Power Options.
Power Schemes Tab
Each standard power setting is called a scheme. If you want to select one of the standard Windows schemes installed on your computer, choose a scheme
from the Power schemes drop-down menu. The settings for each scheme appear in the fields below the scheme name. Each scheme has different settings for
starting standby mode, hibernate mode, turning off the monitor, and turning off the hard drive.
NOTICE: If you set the hard drive to time-out before the monitor does, your computer may appear to be locked up. To recover, press any key on the
keyboard or click the mouse. To avoid this problem, always set the monitor to time-out before the hard drive.
The Power schemes drop-down menu displays the following schemes:
l
l
l
l
l
l
Always On (default) — If you want to use your computer with no power conservation.
Home/Office Desk — If you want your home or office computer to run with little power conservation.
Portable/Laptop — If your computer is a portable computer that you use for traveling.
Presentation — If you want your computer to run without interruption (using no power conservation).
Minimal Power Management — If you want your computer to run with minimal power conservation.
Max Battery — If your computer is a portable computer and you run your computer from batteries for extended periods of time.
If you want to change the default settings for a scheme, click the drop-down menu in the Turn off monitor, Turn off hard disks, System stand by, or System
hibernates field, and then select a time-out from the displayed list. Changing the time-out for a scheme field permanently changes the default settings for that
scheme, unless you click Save As and enter a new name for the changed scheme.
Advanced Tab
The Advanced tab allows you to:
l
l
l
Place the power options icon
in the Windows taskbar for quick access.
Set the computer to prompt you for your Windows password before the computer exits from standby mode or hibernate mode.
Program the power button to activate standby mode, activate hibernate mode, or turn off the computer.
To program these functions, click an option from the corresponding drop-down menu and click OK.
Hibernate Tab
The Hibernate tab allows you to enable hibernate mode. If you want to use the hibernate settings as defined on the Power Schemes tab, click the Enable
hibernate support check box on the Hibernate tab.
For more information on power management options:
1. Click Start, then click Help and Support.
2. In the Help and Support window, click Performance and maintenance.
3. In the Performance and maintenance window, click Conserving power on your computer.
Solving Problems
Dell™ XPS™ 710 Owner's Manual
Troubleshooting Tips
Follow these tips when you troubleshoot your computer:
l
l
l
If you added or removed a part before the problem started, review the installation procedures and ensure that the part is correctly installed.
If a peripheral device does not work, ensure that the device is properly connected.
If an error message appears on the screen, write down the exact message. This message may help support personnel diagnose and fix the problem(s).
If an error message occurs in a program, see the program's documentation.
Battery Problems
CAUTION: There is a danger of a new battery exploding if it is incorrectly installed. Replace the battery only with the same or equivalent type
recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Replace the battery — If you have to repeatedly reset time and date information after turning on the computer, or if an incorrect time or date
displays during start-up, replace the battery (see Replacing the Battery). If the battery still does not work properly, contact Dell (see
Drive Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Ensure that Microsoft® Windows® Recognizes the drive — Click Start, then click My Computer. If the floppy, CD, or DVD drive is not listed,
perform a full scan with your antivirus software to check for and remove viruses. Viruses can sometimes prevent Windows from recognizing
the drive.
Test the drive —
l
l
Insert another floppy disk, CD, or DVD to eliminate the possibility that the original drive is defective.
Insert a bootable floppy disk and restart the computer.
Clean the drive or disk —
Check the cable connections
Run the Dell Diagnostics —
CD and DVD drive problems
NOTE: High-speed CD or DVD drive vibration is normal and may cause noise, which does not indicate a defect in the drive or the CD or DVD.
NOTE: Because of different regions worldwide and different disc formats, not all DVD titles work in all DVD drives.
Adjust the Windows volume control —
l
l
l
Click the speaker icon in the lower-right corner of your screen.
Ensure that the volume is turned up by clicking the slidebar and dragging it up.
Ensure that the sound is not muted by clicking any boxes that are checked.
Problems writing to a CD/DVD-RW drive
Close other programs — The CD/DVD-RW drive must receive a steady stream of data during the writing process. If the stream is interrupted,
an error occurs. Try closing all programs before you write to the CD/DVD-RW.
Turn off standby mode in Windows before writing to a CD/DVD-RW disc — See Standby Mode or search for the keyword standby in
Windows Help and Support Center (click Start, then click Help and Support) for information on power management modes.
Hard drive problems
Run Check Disk —
1. Click Start, then click My Computer.
2. Right-click Local Disk C:.
3. Click Properties.
4. Click the Tools tab.
5. Under Error-checking, click Check Now.
6. Click Scan for and attempt recovery of bad sectors.
7. Click Start.
E-Mail, Modem, and Internet Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: Connect the modem to an analog telephone jack only. The modem does not operate while it is connected to a digital telephone network.
Check the Microsoft Outlook® Express security settings — If you cannot open your e-mail attachments:
1. In Outlook Express, click Tools, click Options, and then click Security.
2. Click Do not allow attachments to remove the checkmark, as needed.
Check the telephone line connection —
Check the telephone jack —
Connect the modem directly to the telephone wall jack —
Use a different telephone line —
l
Verify that the telephone line is connected to the jack on the modem (the jack has either a green label or a connector-shaped icon
next to it).
l
l
l
Ensure that you hear a click when you insert the telephone line connector into the modem.
Disconnect the telephone line from the modem and connect it to a telephone, then listen for a dial tone.
If you have other telephone devices sharing the line, such as an answering machine, fax machine, surge protector, or line splitter,
bypass them and use the telephone to connect the modem directly to the telephone wall jack. If you are using a line that is 3 m (10 ft)
or more in length, try a shorter one.
Run the Modem Helper diagnostics — Click Start, point to All Programs, and then click Modem Helper. Follow the instructions on the screen
to identify and resolve modem problems. Modem Helper diagnostics are not available on all computers.
Verify that the modem is communicating with Windows —
1. Click Start, then click Control Panel.
2. Click Printers and Other Hardware.
3. Click Phone and Modem Options.
4. Click the Modems tab.
5. Click the COM port for your modem.
6. Click Properties, click the Diagnostics tab, and then click Query Modem to verify that the modem is communicating with Windows.
If all commands receive a response, the modem is operating properly.
Ensure that you are connected to the Internet — Ensure that you have subscribed to an Internet provider. With the Outlook Express e-mail
program open, click File. If Work Offline has a checkmark next to it, click the checkmark to remove it and connect to the Internet. For help,
contact your Internet service provider.
Error Messages
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
A filename cannot contain any of the following characters: \ / : * ? " < > | — Do not use these characters in filenames.
A required .DLL file was not found — The program that you are trying to open is missing an essential file. To remove and then reinstall the
program:
1. Click Start, click Control Panel, and then click Add or Remove Programs.
2. Under Currently installed programs, select the program you want to remove.
3. Click Change or Remove.
4. See the program documentation for installation instructions.
drive letter :\ is not accessible. The device is not ready — The drive cannot read the disk. Insert a disk into the drive and try again.
Insert bootable media — Insert a bootable floppy disk or CD.
Non-system disk error — Remove the floppy disk from the floppy drive and restart your computer.
Not enough memory or resources. Close some programs and try again — Close all windows and open the program that you want to use.
In some cases, you may have to restart your computer to restore computer resources. If so, run the program that you want to use first.
NOTE: If the error message is not listed, see the documentation for the operating system or the program that was running when the me]ssage
appeared.
IEEE 1394 Device Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Ensure that the cable for the IEEE 1394 device is properly inserted into the device and into the connector on the computer
If you have problems with a Dell IEEE 1394 device —
If you have problems with an IEEE 1394 device not provided by Dell — Contact the IEEE 1394 device manufacturer.
Keyboard Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Check the keyboard cable —
l
l
Ensure that the keyboard cable is firmly connected to the computer.
Shut down the computer (see Preparing to Work Inside Your Computer), reconnect the keyboard cable as shown on the setup
diagram for your computer, and then restart the computer.
l
l
Ensure that the cable is not damaged or frayed and check cable connectors for bent or broken pins. Straighten any bent pins.
Remove any keyboard extension cables and connect the keyboard directly to the computer.
Test the keyboard — Connect a properly working keyboard to the computer, then try using the keyboard.
Run the Hardware Troubleshooter —
Lockups and Software Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
The computer does not start up
Ensure that the power cable is firmly connected to the computer and to the electrical outlet
The computer stops responding
NOTICE: You may lose data if you are unable to perform an operating system shutdown.
Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the
power button for at least 8 to 10 seconds, until the computer turns off, and then restart your computer.
A program stops responding
End the program —
1. Press <Ctrl><Shift><Esc> simultaneously to access the Windows Task Manager.
2. Click the Applications tab.
3. Click to select the program that is no longer responding.
4. Click End Task.
A program crashes repeatedly
NOTE: Most software includes installation instructions in its documentation or on a floppy disk or CD.
Check the software documentation — If necessary, uninstall and then reinstall the program.
A program is designed for an earlier Windows operating system
Run the Program Compatibility Wizard —
The Program Compatibility Wizard configures a program so that it runs in an environment similar to non-Windows XP operating system
environments.
1. Click Start, point to All Programs® Accessories, and then click Program Compatibility Wizard.
2. In the welcome screen, click Next.
3. Follow the instructions on the screen.
A solid blue screen appears
Turn the computer off — If you are unable to get a response by pressing a key on your keyboard or moving your mouse, press and hold the
power button for at least 8 to 10 seconds, until the computer turns off, and then restart your computer.
Other software problems
Check the software documentation or contact the software manufacturer for troubleshooting information —
l
l
Ensure that the program is compatible with the operating system installed on your computer.
Ensure that your computer meets the minimum hardware requirements needed to run the software. See the software documentation
for information.
l
l
l
Ensure that the program is installed and configured properly.
Verify that the device drivers do not conflict with the program.
If necessary, uninstall and then reinstall the program.
Back up your files immediately
Use a virus-scanning program to check the hard drive, floppy disks, or CDs
Save and close any open files or programs and shut down your computer through the Start menu
Memory Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
If you receive an insufficient memory message —
l
l
l
l
Save and close any open files and exit any open programs you are not using to see if that resolves the problem.
See the software documentation for minimum memory requirements. If necessary, install additional memory (see Installing Memory).
Reseat the memory modules (see Memory) to ensure that your computer is successfully communicating with the memory.
If you experience other memory problems —
l
l
l
Reseat the memory modules (see Memory) to ensure that your computer is successfully communicating with the memory.
Ensure that the memory you are using is supported by your computer. For more information about the type of memory supported by
l
Mouse Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Check the mouse cable —
l
l
l
Ensure that the cable is not damaged or frayed and check cable connectors for bent or broken pins. Straighten any bent pins.
Remove any mouse extension cables, and connect the mouse directly to the computer.
Verify that the mouse cable is connected as shown on the setup diagram for your computer.
Restart the computer —
1. Simultaneously press <Ctrl><Esc> to display the Start menu.
2. Press <u>, press the up- and down-arrow keys to highlight Shut down or Turn Off, and then press <Enter>.
3. After the computer turns off, reconnect the mouse cable as shown on the setup diagram.
4. Turn on the computer.
Test the mouse — Connect a properly working mouse to the computer, then try using the mouse.
Check the mouse settings —
1. Click Start, click Control Panel, and then click Printers and Other Hardware.
2. Click Mouse.
3. Adjusting the settings, as needed.
Network Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
Check the network cable connector — Ensure that the network cable is firmly inserted into the network connector on the back of the
computer and the network jack.
Check the network lights on the back of the computer — If the link integrity light is off (see see Controls and Lights), no network
communication is occurring. Replace the network cable.
Restart the computer and log on to the network again
Check your network settings — Contact your network administrator or the person who set up your network to verify that your network
settings are correct and that the network is functioning.
Power Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
If the power light is blinking green — The computer is in standby mode. Press a key on the keyboard, move the mouse, or press the power
button to resume normal operation.
If the power light is off — The computer is either turned off or is not receiving power.
l
l
l
l
l
Reseat the power cable in the power connector on the back of the computer and the electrical outlet.
Bypass power strips, power extension cables, and other power protection devices to verify that the computer turns on properly.
Ensure that any power strips being used are plugged into an electrical outlet and are turned on.
Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
Ensure that the main power cable and front panel cable are securely connected to the system board (see System Board
If the power light is blinking amber — The computer is receiving electrical power, but an internal power problem may exist.
l
l
Ensure that the voltage selection switch is set to match the AC power at your location (if applicable).
Ensure that all components and cables are properly installed and securely connected to the system board (see System Board
If the power light is steady amber — A device may be malfunctioning or incorrectly installed.
l
Ensure that the processor power cable is securely connected to the system board power connector (POWER2) (see System Board
l
l
Remove and then reinstall any expansion cards, including graphics cards (see Removing PCI and PCI Express Cards).
Eliminate interference — Some possible causes of interference are:
l
l
l
Power, keyboard, and mouse extension cables
Too many devices connected to the same power strip
Multiple power strips connected to the same electrical outlet
Printer Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: If you need technical assistance for your printer, contact the printer's manufacturer.
Check the printer documentation — See the printer documentation for setup and troubleshooting information.
Ensure that the printer is turned on
Check the printer cable connections —
l
l
See the printer documentation for cable connection information.
Ensure that the printer cables are securely connected to the printer and the computer.
Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
Verify that the printer is recognized by Windows —
1. Click Start, click Control Panel, and then click Printers and Other Hardware.
2. Click View installed printers or fax printers.
If the printer is listed, right-click the printer icon.
3. Click Properties, then click the Ports tab. For a parallel printer, ensure that Print to the following port(s): is set to LPT1 (Printer
Port). For a USB printer, ensure that Print to the following port(s): is set to USB.
Reinstall the printer driver — See the printer documentation for information on reinstalling the printer driver.
Scanner Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTE: If you need technical assistance for your scanner, contact the scanner's manufacturer.
Check the scanner documentation — See the scanner documentation for setup and troubleshooting information.
Unlock the scanner — Ensure that your scanner is unlocked (if the scanner has a locking tab or button).
Restart the computer and try the scanner again
Check the cable connections —
l
l
See the scanner documentation for information on cable connections.
Ensure that the scanner cables are securely connected to the scanner and the computer.
Verify that the scanner is recognized by Microsoft Windows —
1. Click Start, click Control Panel, and then click Printers and Other Hardware.
2. Click Scanners and Cameras.
If your scanner is listed, Windows recognizes the scanner.
Reinstall the scanner driver — See the scanner documentation for instructions.
Sound and Speaker Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
No sound from speakers
NOTE: The volume control in MP3 and other media players may override the Windows volume setting. Always check to ensure that the volume on the
media player(s) has not been turned down or off.
Check the speaker cable connections — Ensure that the speakers are connected as shown on the setup diagram supplied with the
speakers. If you purchased a sound card, ensure that the speakers are connected to the card.
Ensure that the subwoofer and the speakers are turned on — See the setup diagram supplied with the speakers. If your speakers have
volume controls, adjust the volume, bass, or treble to eliminate distortion.
Adjust the Windows volume control — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume
is turned up and that the sound is not muted.
Disconnect headphones from the headphone connector — Sound from the speakers is automatically disabled when headphones are
connected to the computer's front-panel headphone connector.
Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
Eliminate possible interference — Turn off nearby fans, fluorescent lights, or halogen lamps to check for interference.
Run the speaker diagnostics
No sound from headphones
Check the headphone cable connection — Ensure that the headphone cable is securely inserted into the headphone connector (see Front
Adjust the Windows volume control — Click or double-click the speaker icon in the lower-right corner of your screen. Ensure that the volume
is turned up and that the sound is not muted.
Video and Monitor Problems
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: If your computer came with a PCI graphics card installed, removal of the card is not necessary when installing additional graphics cards;
however, the card is required for troubleshooting purposes. If you remove the card, store it in a safe and secure location.
The screen is blank
NOTE: For troubleshooting procedures, see the monitor's documentation.
Check the monitor cable connection —
l
l
l
l
l
l
Ensure that the monitor cable is connected to the correct graphics card (for dual graphics card configurations).
If you are using the optional DVI-to-VGA adapter, ensure that the adapter is correctly attached to the graphics card and monitor.
Ensure that the monitor cable is connected as shown on the setup diagram for your computer.
Remove any video extension cables and connect the monitor directly to the computer.
Swap the computer and monitor power cables to determine if the monitor's power cable is defective.
Check the connectors for bent or broken pins (it is normal for monitor cable connectors to have missing pins.)
Check the monitor power light —
l
l
l
If the power light is lit or blinking, the monitor has power.
If the power light is off, firmly press the button to ensure that the monitor is turned on.
If the power light is blinking, press a key on the keyboard or move the mouse to resume normal operation.
Test the electrical outlet — Ensure that the electrical outlet is working by testing it with another device, such as a lamp.
The screen is difficult to read
Check the monitor settings — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing
(degaussing) the monitor, and running the monitor self-test.
Move the subwoofer away from the monitor — If your speaker system includes a subwoofer, ensure that the subwoofer is positioned at
least 60 cm (2 ft) away from the monitor.
Move the monitor away from external power sources — Fans, fluorescent lights, halogen lamps, and other electrical devices can cause the
screen image to appear shaky. Turn off nearby devices to check for interference.
Rotate the monitor to eliminate sunlight glare and possible interference
Adjust the Windows display settings —
1. Click Start, click Control Panel, and then click Appearance and Themes.
2. Click Display, then click the Settings tab.
3. Adjust Screen resolution and Color quality settings, as needed.
The image quality is poor
Check the graphics card power cable connection — Ensure that the power cable for the graphics card(s) is correctly attached to the card.
Check the monitor settings — See the monitor documentation for instructions on adjusting the contrast and brightness, demagnetizing
(degaussing) the monitor, and running the monitor self-test.
Dell™ XPS™ 710 Owner's Manual
NOTE: A NOTE indicates important information that helps you make better use of your computer.
NOTICE: A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.
CAUTION: A CAUTION indicates a potential for property damage, personal injury, or death.
®
®
If you purchased a Dell™ n Series computer, any references in this document to Microsoft Windows operating systems are not applicable.
Information in this document is subject to change without notice.
© 2006 Dell Inc. All rights reserved.
Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.
Trademarks used in this text: Dell, the DELL logo, Dell XPS, Inspiron, Dell Precision, Dimension, OptiPlex, Latitude, PowerEdge, PowerVault, PowerApp, and Dell OpenManage are
trademarks of Dell Inc.; Intel, Pentium, and Celeron are registered trademarks of Intel Corporation; Microsoft and Windows are registered trademarks of Microsoft Corporation.
Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.
October 2006 P/N XM141 Rev. A00
Advanced Troubleshooting
Dell™ XPS™ 710 Owner's Manual
Diagnostic Lights
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
To help troubleshoot a problem, your computer has four lights labeled 1, 2, 3, and 4 on the front panel (see Front View). When the computer starts normally,
the lights flash before turning off. If the computer malfunctions, the sequence of the lights help to identify the problem.
NOTE: After the computer completes POST, all four lights turn off before booting to the operating system.
Light Pattern
Problem Description
Suggested Resolution
The computer is in a normal off
condition or a possible pre-BIOS
failure has occurred.
l
l
The diagnostic lights are not lit
after the system successfully
boots to the operating system.
A possible processor failure has
occurred.
l
l
Memory modules are detected,
but a memory failure has
occurred.
l
normally, continue to install additional memory modules (one at a time) until you have identified a
faulty module or reinstalled all modules without error.
l
l
A possible graphics card failure
has occurred.
l
l
l
If available, install a working graphics card into your computer.
A possible floppy drive or hard
drive failure has occurred.
Reseat all power and data cables.
A possible USB failure has
occurred.
Reinstall all USB devices and check all cable connections.
No memory modules are
detected.
l
normally, continue to install additional memory modules (one at a time) until you have identified a
faulty module or reinstalled all modules without error.
l
l
Memory modules are detected,
but a memory configuration or
compatibility error has occurred.
l
Ensure that no special requirements for memory module/connector placement exist (see
Memory).
l
l
A possible expansion card failure
has occurred.
1. Determine if a conflict exists by removing an expansion card (not a graphics card) and restarting
2. If the problem persists, reinstall the card you removed, then remove a different card and restart
the computer.
3. Repeat this process for each expansion card installed. If the computer starts normally,
Another failure has occurred.
l
l
l
Ensure that all hard drive and CD/DVD drive cables are properly connected to the system board
If there is an error message on the screen identifying a problem with a device (such as the
floppy drive or hard drive), check the device to make sure it is functioning properly.
If the operating system is attempting to boot from a device (such as the floppy drive or CD/DVD
devices installed on your computer.
l
Dell Diagnostics
CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
When to Use the Dell Diagnostics
If you experience a problem with your computer, perform the checks in Solving Problems and run the Dell Diagnostics before you contact Dell for technical
assistance.
NOTE: The Dell Diagnostics only operate on Dell computers.
Run Dell Diagnostics from your hard drive or from the Drivers and Utilities CD (ResourceCD).
Starting the Dell Diagnostics From Your Hard Drive
1. Turn on (or restart) your computer.
2. When the DELL logo appears, press <F12> immediately.
NOTE: Keyboard failure may result when a key is held down for extended periods of time. To avoid possible keyboard failure, press and release
<F12> in even intervals to open the Boot Device Menu.
NOTE: If at any time a message appears stating that no diagnostics utility partition has been found, run the Dell Diagnostics from your Drivers and
If you wait too long and the operating system logo appears, continue to wait until you see the Microsoft® Windows® desktop, then shut down your
computer and try again.
3. At the Boot Device Menu, use the up- and down-arrow keys or press the appropriate number on the keyboard to highlight Boot to Utility Partition,
and then press <Enter>.
NOTE: The Quickboot feature changes the boot sequence for the current boot only. Upon restart, the computer boots according to the boot
sequence specified in system setup.
4. At the Dell Diagnostics Main Menu, left-click with the mouse, or press <Tab> and then <Enter>, to select the test you want to run (see Dell Diagnostics
NOTE: Write down any error codes and problem descriptions exactly as they appear and follow the instructions on the screen.
5. After all tests have completed, close the test window to return to the Dell Diagnostics Main Menu.
6. Close the Main Menu window to exit the Dell Diagnostics and restart the computer.
Starting the Dell Diagnostics From the Drivers and Utilities CD
1. Turn on your computer.
2. Press the eject button on the front of the optical drive to open the drive tray.
3. Place the Drivers and Utilities CD in the center of the drive tray, then press the eject button or gently push on the tray to close it.
4. Restart the computer.
5. When the DELL logo appears, press <F12> immediately.
NOTE: Keyboard failure may result when a key on the keyboard is held down for extended periods of time. To avoid possible keyboard failure,
press and release <F12> in even intervals until the Boot Device Menu appears.
If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop, then shut down your computer and try again.
6. At the Boot Device Menu, use the up- and down-arrow keys or press the appropriate number on the keyboard to highlight Onboard or USB CD-ROM,
and then press <Enter>.
NOTE: The Quickboot feature changes the boot sequence for the current boot only. Upon restart, the computer boots according to the boot
sequence specified in system setup.
7. At the CD-ROM Startup Menu, use the up- and down-arrow keys or press the appropriate number on the keyboard to highlight Boot from CD-ROM,
and then press <Enter>.
If you wait too long and the Windows logo appears, continue to wait until you see the Windows desktop, then shut down your computer and try again.
8. Press <1> to select the Dell Diagnostics.
9. At the Dell Diagnostics Menu press <1> to select the Dell Diagnostics for ResourceCD (graphical user interface).
10. At the Dell Diagnostics Main Menu, left-click with the mouse, or press <Tab> and then <Enter>, to select the test you want to run (see Dell Diagnostics
NOTE: Write down any error codes and problem descriptions exactly as they appear and follow the instructions on the screen.
11. After all tests have completed, close the test window to return to the Dell Diagnostics Main Menu.
12. Remove the Drivers and Utilities CD, then close the Main Menu window to exit the Dell Diagnostics and restart the computer.
Dell Diagnostics Main Menu
The following tests can be run from the Dell Diagnostics Main Menu:
Option
Function
Express Test Performs a quick test of system devices. The test typically takes 10 to 20 minutes and requires no interaction on your part. Run Express Test
first to increase the possibility of tracing the problem quickly.
Extended
Test
Performs a thorough check of system devices. The test typically takes an hour or more and peridocially requires your input to answer specific
questions.
Custom Test Tests a specific device in the system and can be used to customize the tests you want to run.
Symptom
Tree
Lists a number of common symptoms and allows you to select a test based on the symptom of the problem you are having.
For any problem encountered during a test, a message appears with an error code and a description of the problem. Write down the error code and problem
description exactly as it appears and follow the instructions on the screen. If you cannot resolve the problem, contact Dell (see Contacting Dell).
NOTE: The Service Tag for your computer is located at the top of each test screen. When contacting Dell support, have your Service Tag ready.
The following tabs provide additional information for tests run from the Custom Test or Symptom Tree option:
Tab
Function
Results
Errors
Displays the results of the test and any error conditions encountered.
Displays error conditions encountered, error codes, and the problem description.
Describes the test and any requirements for running the test.
Displays the hardware configuration for the selected device.
Help
Configuration
(Custom Test only) The Dell Diagnostics obtains configuration information for all devices from system setup, memory, and various
internal tests, and it displays the information in the device list in the left pane of the screen.
NOTE: The device list may not display the names of all the components installed on your computer or all devices
attached to your computer.
Parameters
(Custom Test only)
Allows you to customize the test, if applicable, by changing the test settings.
Drivers
What Is a Driver?
A driver is a program that controls a device such as a printer, mouse, or keyboard. All devices require a driver program.
A driver acts as a translator between the device and any programs that use the device. Each device has a set of specialized commands that only driver for
that device recognizes.
Required drivers are already installed on your computer—no further installation or configuration is needed.
NOTICE: The Drivers and Utilities CD may contain drivers for operating systems that are not on your computer. Ensure that you are installing software
appropriate for your operating system.
®
®
Many drivers, such as the keyboard driver, come with your Microsoft Windows operating system. You may need to install drivers if you:
l
l
l
Upgrade your operating system.
Reinstall your operating system.
Connect or install a new device.
Identifying Drivers
If you experience a problem with any device, identify whether the driver is the source of your problem and, if necessary, update the driver.
Windows XP
1. Click Start, then click Control Panel.
2. Under Pick a Category, click Performance and Maintenance.
3. Click System.
4. In the System Properties window, click the Hardware tab.
5. Click Device Manager.
6. Scroll down the list of devices and check for an exclamation point (a circle with a [!]) next to the device name.
If an exclamation point appears next to the device name, you may need to reinstall the driver or install a new driver (see Drivers).
Reinstalling Drivers
NOTICE: The Dell Support website at support.dell.com and your Drivers and Utilities CD provide approved drivers for your Dell computer. If you install
drivers obtained from other sources, your computer may not function properly.
Using Windows XP Device Driver Rollback
If a problem occurs on your computer after you install or update a driver, use Windows XP Device Driver Rollback to replace the driver with the previously
installed version.
1. Click Start, then click Control Panel.
2. Under Pick a Category, click Performance and Maintenance.
3. Click System.
4. In the System Properties window, click the Hardware tab.
5. Click Device Manager.
6. Right-click the device for which the new driver was installed, then click Properties.
7. Click the Driver tab.
8. Click Roll Back Driver.
If Device Driver Rollback does not resolve the problem, reinstall the driver from the Drivers and Utilities CD.
Using the Drivers and Utilities CD
If a problem occurs on your computer after you install or update a driver and Windows XP Device Driver Rollback does not resolve the problem, reinstall the
driver from the Drivers and Utilities CD.
1. With the Windows desktop displayed, insert the Drivers and Utilities CD.
If this is your first time to use the Drivers and Utilities CD, proceed to step 2. If not, go to step 4.
2. When the ResourceCD Installation window appears, click OK, and then follow the instructions on the screen.
3. When the InstallShield Wizard Completed window appears, click Finish.
The ResourceCD window appears.
4. Under Welcome Dell System Owner, click Next.
5. Click Drivers.
The drivers that are used by your computer are automatically displayed in the Drivers window.
NOTE: The ResourceCD displays drivers only for the hardware that came installed in your computer. If you installed additional hardware, and
applicable drivers are not displayed, exit the ResourceCD program and see the documentation that came with the hardware.
6. Click the driver that you want to reinstall.
NOTE: If a driver for a particular device is not listed, then a driver for that device is already included with the operating system.
7. Click Extract, and then follow the instructions on the screen.
If reinstalling the driver from the Drivers and Utilities CD does not resolve the problem, use System Restore to return the computer to the operating state
Manually Reinstalling Drivers
After extracting driver files from the Drivers and Utilities CD to your hard drive you may be required to update the driver manually.
Drivers can be manually updated for any hardware device installed in your computer.
1. Click Start, then click Control Panel.
2. Under Pick a Category, click Performance and Maintenance.
3. Click System.
4. In the System Properties window, click the Hardware tab.
5. Click Device Manager.
6. Double-click the type of device for which you are installing the driver.
7. Right-click the device for which the driver is being reinstalled, then click Properties.
8. Click the Driver tab.
9. Click Update Driver.
10. Click Install from a list or specific location (Advanced), then click Next.
11. Click to check Include this location in the search, then click Browse and navigate to where the driver files are located on your hard drive.
12. When the name of the appropriate driver appears, click Next.
13. Click Finish and restart your computer.
Using Microsoft® Windows® XP System Restore
Microsoft Windows XP System Restore allows you to return your computer to an earlier operating state (without affecting data files). Using System Restore can
be helpful if changes to the system hardware, software, or settings have left the computer in an undesirable operating state. For information on using System
Restore, see the Windows Help and Support Center (click Start, then click Help and Support).
NOTICE: System Restore does not monitor your data files or recover them. Make regular backups of your data files.
Creating a Restore Point
1. Click Start, point to All Programs® Accessories® System Tools, and then click System Restore.
2. Ensure that Create a restore point is selected, then click Next.
3. In the Restore point description field, enter a name for the restore point, then click Create.
Restoring the Computer to an Earlier Operating State
NOTICE: Before you restore the computer to an earlier operating state, save and close all open files and exit any open programs. Do not alter, open, or
delete any files or programs until the system restoration process is complete.
NOTE: If a problem occurs after you install a device driver, first try to resolve the problem by using Windows XP Device Driver Rollback (see Using
Windows XP Device Driver Rollback), or reinstall the driver with the Drivers and Utilities CD (see Using the Drivers and Utilities CD).
1. Click Start, point to All Programs® Accessories® System Tools, and then click System Restore.
2. Ensure that Restore my computer to an earlier time is selected, then click Next.
3. Under Select a Restore Point, click the calendar date and restore point to which you want to restore your computer, and then click Next.
NOTE: Calendar dates with available restore points appear in bold. If a calendar date has only one restore point available, that restore point is
automatically selected.
4. Under Conform Restore Point Selection, click Next.
The System Restore process collects necessary data, then restarts the computer.
5. Under Restoration Complete (after the computer has restarted), click OK.
NOTE: After your computer has been restored to an earlier operating state, you can repeat the restoration process and use a different restore point, or
you can undo the restoration and return the computer to its original operating state.
Undoing the Last System Restore
NOTICE: Before you undo the most recent system restore, save and close all open files and exit any open programs. Do not alter, open, or delete any
files or programs until the system restoration process is complete.
1. Click Start, point to All Programs® Accessories® System Tools, and then click System Restore.
2. Ensure that Undo my last restoration is selected, then click Next.
3. Under Confirm Restoration Undo, click Next.
The System Restore process collects necessary data, then restarts the computer.
4. Under Undo Complete (after the computer has restarted), click OK.
Enabling or Disabling System Restore
If you reinstall Windows XP with less than 200 MB of free hard-disk space available, System Restore is automatically disabled. To determine if System Restore
is enabled:
1. Click Start, then click Control Panel.
2. Under Pick a Category, click Performance and Maintenance.
3. Click System.
4. In the System Properties window, click the System Restore tab.
5. Ensure that Turn off System Restore is unchecked.
NOTE: To disable System Restore, check Turn off System Restore.
Resolving Software and Hardware Incompatibilities
If a device is not detected during the operating system setup or is detected, but incorrectly configured, you can use the Hardware Troubleshooter to resolve
the incompatibility.
1. Click Start, then click Help and Support.
2. Type hardware troubleshooter in the Search field and click the arrow to start the search.
3. Click Hardware Troubleshooter in the Search Results list.
4. In the Hardware Troubleshooter list, click I need to resolve a hardware conflict on my computer, and click Next.
Reinstalling Microsoft® Windows® XP
NOTICE: You must use Windows XP Service Pack 1 (SP1) or later when you reinstall Windows XP.
NOTICE: In order to use the migrating option to convert a RAID configuration without losing data, your hard drive must initially be set up as a single
drive RAID 0 array before the operating system is loaded onto the drive (see Using the Nvidia MediaShield ROM Utility for instructions).
Before You Begin
If you are considering reinstalling the Windows XP operating system to correct a problem with a newly installed driver, first try using Windows XP Device Driver
Rollback (see Using Windows XP Device Driver Rollback). If Device Driver Rollback does not resolve the problem, then use System Restore (see Using
Microsoft® Windows® XP System Restore) to return your operating system to the operating state it was in before you installed the new device driver.
NOTICE: Before performing the installation, back up all data files on your primary hard drive. For conventional hard drive configurations, the primary
hard drive is the first drive detected by the computer.
To reinstall Windows XP, you need the following items:
l
l
Dell Operating System CD
Dell Drivers and Utilities CD
NOTE: The Drivers and Utilities CD contains drivers that were installed during assembly of the computer. Use the CD to load any required drivers.
Reinstalling Windows XP
To reinstall Windows XP, perform all the steps in the following sections in the order in which they are listed.
The reinstallation process can take 1 to 2 hours to complete. After you reinstall the operating system, you must also reinstall the device drivers, virus
protection program, and other software.
NOTICE: The Operating System CD provides options for reinstalling Windows XP. The options can overwrite files and possibly affect programs installed
on your hard drive. Therefore, do not reinstall Windows XP unless a Dell technical support representative instructs you to do so.
NOTICE: To prevent conflicts with Windows XP, disable any virus protection software installed on your computer before you reinstall Windows XP. See
the documentation that came with the software for instructions.
Booting From the Operating System CD
1. Save and close any open files and exit any open programs.
2. Insert the Operating System CD. Click Exit if Install Windows XP message appears.
3. Restart the computer.
4. When the DELL logo appears, press <F12> immediately.
NOTE: Keyboard failure may result when a key on the keyboard is held down for extended periods of time. To avoid possible keyboard failure,
press and release <F12> in even intervals until the Boot Device Menu appears.
If the operating system logo appears, wait until you see the Windows desktop, and then shut down the computer and try again.
5. At the Boot Device Menu, use the up- and down-arrow keys or press the appropriate number on the keyboard to highlight Onboard or USB CD-ROM,
and then press <Enter>.
6. When the Press any key to boot from CD message appears, press any key.
Windows XP Setup
1. When the Windows XP Setup screen appears, press <Enter> to select To set up Windows now.
2. Read the information on the Microsoft Windows Licensing Agreement screen, and press <F8> to accept the license agreement.
3. If your computer already has Windows XP installed and you want to recover your current Windows XP data, type rto select the repair option, and
remove the CD.
4. If you want to install a new copy of Windows XP, press <Esc> to select that option.
5. Press <Enter> to select the highlighted partition (recommended), and follow the instructions on the screen.
The Windows XP Setup screen appears, and the operating system begins to copy files and install the devices. The computer automatically restarts
multiple times.
NOTE: The time required to complete the setup depends on the size of the hard drive and the speed of your computer.
NOTICE: Do not press any key when the following message appears: Press any key to boot from the CD.
6. When the Regional and Language Options screen appears, select the settings for your location and click Next.
7. Enter your name and organization (optional) in the Personalize Your Software screen, and click Next.
8. If you are reinstalling Windows XP Home Edition, at the What's your computer's name window, enter a name for your computer (or accept the name
provided) and click Next.
If you are reinstalling Windows XP Professional, at the Computer Name and Administrator Password window, enter a name for your computer (or accept
the one provided) and a password, and click Next.
9. If the Modem Dialing Information screen appears, enter the requested information and click Next.
10. Enter the date, time, and time zone in the Date and Time Settings window, and click Next.
11. If the Networking Settings screen appears, click Typical and click Next.
12. If you are reinstalling Windows XP Professional and you are prompted to provide further information regarding your network configuration, enter your
selections. If you are unsure of your settings, accept the default selections.
Windows XP installs the operating system components and configures the computer. The computer automatically restarts.
NOTICE: Do not press any key when the following message appears: Press any key to boot from the CD.
13. When the Welcome to Microsoft screen appears, click Next.
14. When the How will this computer connect to the Internet? message appears, click Skip.
15. When the Ready to register with Microsoft? screen appears, select No, not at this time and click Next.
16. When the Who will use this computer? screen appears, you can enter up to five users.
17. Click Next.
18. Click Finish to complete the setup, and remove the CD.
20. Reinstall your virus protection software.
21. Reinstall your programs.
NOTE: To reinstall and activate your Microsoft Office or Microsoft Works Suite programs, you need the Product Key number located on the back of
the Microsoft Office or Microsoft Works Suite CD sleeve.
|
Zenoah G380pu User Manual
Toyota Automobile Parts Rm744u User Manual
Snapper 1694923 User Manual
Roberts Gorden Combat At 254 User Manual
Philips Lr6px20c User Manual
Panasonic Cs Te12dke User Manual
Mitsubishi Mr Slim Nh41nad User Manual
Makita Dc1850 User Manual
Dewalt Dwf83pl User Manual
CRAFTSMAN 320.48291 User Manual