Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL - Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO” -
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA BOLOGNA (ITALIA)
3) Connections, controls, first turn on
All the connections and controls are in the amplifier
panel side:
1) Balanced Audio Input (XLR type)
2) Audio Attenuation
3) RDNet connections with LEDs
4) Output link
5) Status LEDs
6) DSP Preset (HPF)
7) USB data Service (firmware update)
8) Auto Range Mains Input
9) Mains Link
10) Mains Fuse
a) Connect the audio input (1).
Adjust the level of Attenuation (2).
b) If you need to link VIO X205 to another one, please
use a cable with XLR connectors (not supplied).
Connect the Link output (4) of the first, to the balanced
Input (1) of the second one.
c) Set properly the DSP preset switch (6). It is possible
to apply an HPF filter [Fullrange, 85, 90, 95, 100, 110,
120 Hz].
d) In case of remote control, connect the proper
Data Input (3) of the first module to
the hardware remote controller (RDNet Control 2 or
RDNet Control 8) with cables equipped with
etherCON connectors. Then connect the Data Output
(3) of the first module to the Data Input (3) of the
second one, and so on.
When the RDNet network is on and it has
recognized the connected device, the LED “Link” is
on. The other LED “Active” start blinking when
there is the presence of data transmission, the
“Remote Preset Active” advise that all the local
controls set on the amplifier panel (level, DSP
presets, etc.) are by-passed and controlled remotely
by RDNet.
See also RDNet Control 2 and RDNet Control 8 user
manuals for further information.
e) Plug properly the mains PowerCON TRUE1 input
cable (supplied) in the related input (8).
Check the complete user manual on www.dbtechnologies.com
for further information about the system and available
accessories.
ogni ulteriore informazione sul sistema e sugli accessori
disponibili.
Für weitere Informationen und verfügbares Zubehör lesen sie
bitte die vollständige Bedienungsanleitung unter
Vérifiez le manuel de l'utilisateur complet sur
www.dbtechnologies.com pour des informations
complémentaires du système et des accessoires disponibles.
Compruebe el manual de usuario completo sobre
www.dbtechnologies.com para la información adicional sobre
el sistema y accesorios disponibles.
Technical Data
Processor and user interface
Controller: 28/56 bit
Speaker Type: 2-way wooden active speaker
Usable Bandwidth [-10 dB]: 75 – 21000 Hz
Frequency Response [-6 dB]: 80 - 20000 Hz
Max SPL (1 m): 126 dB
AD/DA Conversion: 24 bit 48 kHz
Limiter: Peak, RMS, Thermal
Controls: DSP Rotary Encoder, Attenuation,
HF: 1 " Exit
Input / Output
HF voice coil: 1.4”
LF (2x): 5”
Mains connections: PowerCON TRUE
Signal Inputs: 1 x balanced XLR
Signal Out: 1 x balanced XLR
RDNet: Data In, Data Out
LF Voice Coil: 1”
Crossover frequency: 1500 Hz (24 dB/oct)
Coverage pattern:
60° / 60°( VIO X205-60) - 100° /100° (VIO X205-100)
Mechanics
Amplifier
Housing: Wooden Box
Grille: Full metal grille
Width: 150 mm (5.9 in)
Height: 485 mm (19 in)
Depth: 240 mm (9.4 in)
Weight: 7.8 kg (17.2 lbs)
Amp Technology: Digipro G3
Amp Class: Class-D
RMS Power: 400 W
Operating voltage (auto-range):
220-240V~ (50-60Hz) /
100-120V~ (50-60 Hz)
.
Scan with your QR Reader
App to download the
complete User Manual
Download the complete user manual from the site:
EMI CLASSIFICATION
According to the standards EN 55032 and EN 55035 this equipment is designed and suitable to operate in class B electromagnetic
environments
.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties. For safety reasons
do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check all the components for damages,
deformations, missing or damaged parts that may compromise safety during installation. If you use the loudspeakers outdoor avoid spots exposed to bad weather
conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by inappropriate accessories
or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
|