Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL - Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO” -
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA BOLOGNA (ITALIA)
3) Connections and controls
1 – Balanced XLR inputs
2 – Balanced XLR outputs
All the connections and controls are in the amplifier
panel side:
3 – Subwoofer level rotary
4 – Outputs Mode (Link or Xover mode)
5 – Subwoofer Setup (Polarity switch) and
Subwoofer Mode button (Flat/Boosted)
6 – LEDs (Limiter, Signal / ON)
7 – Mains input connector
8 – Power switch (ON, OFF)
a) Once you have properly set up the desired
configuration (see also the complete user manual and
accessories instructions for further information),
connect the audio input (mono) or inputs (stereo) (1).
Connect the output (mono) or outputs (stereo) (2) and
consequently set the Subwoofer level to 0 dB in the
right position (3).
b) Set properly the Outputs Mode (4): “Link” in case of
direct link connection, “Xover” for example in case of
use with a OPERA or B-HYPE series model.
c) Choose the Subwoofer Polarity (Normal or Reverse)
(5) to obtain the proper behavior. It is possible to add
a low-frequencies boost (5) with the related Subwoofer
Mode switch.
d) Connect the VDE cable to the related connector (7).
Then turn ON the power switch (8). The, the
“Signal/ON” LED (6) turns on, signaling the proper
power connection, and starts blinking at the presence
of audio signal (greater than -20 dBu).
Check the complete user manual on www.dbtechnologies.com
for further information about the system and available
accessories.
ogni ulteriore informazione sul sistema
e
sugli accessori
disponibili.
Für weitere Informationen und verfügbares Zubehör lesen sie
bitte
Vérifiez le manuel
die
vollständige
Bedienungsanleitung
unter
de
l'utilisateur
pour des
complet
informations
sur
complémentaires du système et des accessoires disponibles.
Compruebe el manual de usuario completo sobre
www.dbtechnologies.com para la información adicional sobre el
sistema y accesorios disponibles.
Technical Data
Processor and user interface
Controller: 28/56 bit DSP
Speaker Type: Active subwoofer
Usable Bandwidth [-10 dB]: 46 – 123 Hz
Max SPL (1 m): 129 dB
LF: 12”
Limiter: Peak, Thermal, RMS
Controls: Subwoofer level, Outputs mode, Polarity,
Subwoofer mode
LF Voice Coil: 2.5”
Inputs / Outputs
Amplifier
Signal Input: 2 x XLR (balanced)
Signal Out: 2 x XLR (balanced)
Mains connections: VDE
Amp Technology: SMPS digital amplifier
Amp Class: Class-D – Passive cooling (convection)
RMS Power: 600 W
Mechanics
Peak Power: 1200 W
Housing: Plywood
Operating voltage (factory set)
220-240V~ (50-60Hz) or
:
Grille: Full metal grille
Pole Mount: Yes, M20
Width: 360 mm (14.72 in)
Height: 550 mm (21.65 in)
Depth: 525 mm (20.67 in)
Weight: 19.8 kg (43.65 lbs.)
110-120V~ (50-60 Hz)
Scan with your QR Reader
App to download the
complete User Manual
Download the complete user manual on: www.dbtechnologies.com/EN/Downloads.aspx
EMI CLASSIFICATION
According to the standards EN 55103 this equipment is designed and suitable to operate in E3 (or lower E2, E1) Electromagnetic environments.
FCC CLASS B STATEMENT ACCORDING TO TITLE 47, PART 15, SUBPART B, §15.105
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.
dBTechnologies reserves the right to make changes or improvements in design or manufacturing without assuming any obligation to change
or improve products previously manufactured.
|