Quick start user manual
Section 1
The warnings in this manual must be observed together with the "USER MANUAL - Section 2".
Le avvertenze nel presente manuale devono essere osservate congiuntamente al “MANUALE D’USO - Sezione2”.
Die Warnungen in diesem Handbuch müssen in Verbindung mit der "BEDIENUNGSANLEITUNG - Abschnitt 2" beobachtet
werden”.
Les avertissements specifiés dans ce manuel doivent être respectés ainsi que les "CARACTERISTIQUES TECHNIQUES -
Section 2"
Las advertencias del presente manual se deben tener en cuenta conjuntamente con las del “MANUAL DEL USUARIO” -
Sección 2”.
A.E.B. Industriale Srl Via Brodolini, 8 Località Crespellano 40053 VALSAMOGGIA BOLOGNA (ITALIA)
3) Connections and controls
a) Connect the audio input (1). In case of
a
microphone, plug it and select “Mic” in the Input
sensitivity switch (6). In the other cases check that the
switch is set on “Line”. Adjust the level of Sensitivity
(2).
b) If you need to link FMX 10 to another one, please
use a cable with XLR connectors (not supplied).
Connect the Link output (3) of the first, to the balanced
Input (1) of the second one. In the second loudspeaker,
please check that the switch (6) is set on “Line” position
and that Sensitivity (3) is set to the correct value.
c) Set properly the DSP preset using the Main EQ
Rotary (4). You can choose between:
1. Live Monitor, for a single monitor use on the
stage in live performance
2. Playback Monitor, for a single monitor use on
the stage in playback performance
3. Coupled Monitors, for a double monitor live
usage
4. Male Singer, to enhance male vocal
performance
5. Female Singer, to enhance female vocal
performance
6. Antifeedback, to avoid Larsen effect in live
performaces
7. Live on Stand, for an optimization of the
monitor in vertical usage and live performance
8. Playback on Stand for an optimization of the
monitor in vertical usage and playback
performance
d) Plug properly the mains VDE input cable (supplied)
in the related input (7). Then switch the POWER switch
(8) to “ON” position. Increase gradually the volume of
the audio source to the desired level.
All the connections and
controls are in the amplifier
panel, on the side of the
monitor:
Check the complete user manual on www.dbtechnologies.com
for further information about the system and available
accessories.
1) Balanced Audio Input
2) Input sensitivity
3) Output/Link
4) Main EQ Rotary
5) Status LEDs
6) Line/Mic switch
7) VDE input with fuse
8) Power ON/OFF switch
ogni ulteriore informazione sul sistema
disponibili.
e
sugli accessori
Für weitere Informationen und verfügbares Zubehör lesen sie
bitte
Vérifiez le manuel
die
vollständige
Bedienungsanleitung
unter
de
l'utilisateur
pour des
complet
informations
sur
complémentaires du système et des accessoires disponibles.
Compruebe el manual de usuario completo sobre
www.dbtechnologies.com para la información adicional sobre el
sistema y accesorios disponibles.
Technical Data
Processor and user interface
Controller: 28/56 bit DSP
Speaker Type: Coaxial Active Stage Monitor
Usable Bandwidth [-10 dB]: 57 – 19000 Hz
Frequency Response [-6 dB]: 65 – 16500 Hz
Max SPL (1 m): 125 dB
AD/DA Conversion: 24 bit - 48 kHz
Limiter: Peak, thermal, RMS
Controls: DSP programs rotary encoder, Line/Mic switch,
Input Sensitivity level
HF compression driver: 1 " Exit
HF voice coil: 1”
Input / Output
LF: 10”
LF Voice Coil: 2”
Mains connections: VDE
Crossover frequency: 1800 Hz (24 dB/oct)
Horizontal dispersion: 60° (rotatable horn)
Vertical dispersion: 90° (rotatable horn)
Signal Inputs: 1 x balanced XLR connector
Signal Out/Link: 1 x balanced XLR connector
Mechanics
Amplifier
Housing: Wooden Box
Grille: Full metal grille
Pole Mount Hole: Yes, 36 mm
Width: 390 mm (15.35 in)
Height: 268 mm (10.55 in)
Depth: 411 mm (16.18 in)
Weight: 11.3 kg (24.9 lbs)
PSU Technology: SMPS
Amp Class: Class-D
RMS Power: 400 W
Operating voltage (factory internal setup):
220-240V~ (50-60Hz) or
100-120V~ (50-60 Hz)
Scan with your QR Reader
App to download the
complete User Manual
Download the complete user manual from the site:
EMI CLASSIFICATION
According to the standards EN 55032 and EN 55035 this equipment is designed and suitable to operate in class B electromagnetic
environments.
FCC CLASS B STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)this device may not cause harmful
interference,and (2)this device must accept any interference received,including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
WARNING: Make sure that the loudspeaker is securely installed in a stable position to avoid any injuries or damages to persons or properties.
For safety reasons do not place one loudspeaker on top of another without proper fastening systems. Before hanging the loudspeaker check
all the components for damages, deformations, missing or damaged parts that may compromise safety during installation. If you use the
loudspeakers outdoor avoid spots exposed to bad weather conditions.
Contact dB Technologies for accessories to be used with speakers. dBTechnologies will not accept any responsibility for damages caused by
inappropriate accessories or additional devices.
Features, specification and appearance of products are subject to change without notice.dBTechnologies reserves the right to make
changes or improvements in design or manufacturing without assuming any obligation to change or improve products previously
manufactured.
|