INSTRUCTION BOOKLET
Recipe
Booklet
Reverse Side
Griddler® Elite
GR-300WS
For your safety and continued enjoyment of this product, always read the instruction book carefully before using.
16.Do not operate your appliance in an
appliance garage or under a wall
cabinet. When storing in an
appliance garage always unplug
the unit from the electrical outlet.
Not doing so could create a risk of
fire, especially if the appliance
touches the walls of the garage or
the door touches the unit as it
closes.
Important
SafeguardS
1. READ ALL INSTRUCTIONS.
2. Unplug from outlet when not in
use and before cleaning. Allow to
cool before putting on or taking
off parts, and before cleaning
appliance.
3. Do not touch hot surfaces; use
handles, knobs or buttons.
4. To protect against fire, electric
shock, and injury to persons, DO
NOT IMMERSE CORD OR PLUG
in water or other liquids.
5. Close supervision is necessary when
any appliance is used by or near
children.
6. Do not operate any appliance with a
damaged cord or plug, or after the
appliance has malfunctioned or has
been damaged in any manner.
SaVe tHeSe
InStruCtIonS
for HouSeHoLd
uSe onLY
SpeCIaL
Cord Set
InStruCtIonS
Return the appliance to the nearest
Cuisinart Repair Center for
examination, repair or adjustment.
A short power-supply cord is provided to
reduce the risks resulting from becoming
entangled in or tripping over a longer
cord. Extension cords may be used if
care is exercised in their use.
7. The use of accessory attachments
not recommended by Cuisinart may
result in fire, electrical shock, or risk
of injury to persons.
If an extension cord is used, the marked
electrical rating of the extension cord
should be at least as great as the
8. Do not use outdoors.
electrical rating of the appliance, and the
longer cord should be arranged so that it
will not drape over the countertop or
tabletop where it can be pulled on by
children or animals, or tripped over.
9. Do not let power cord hang over
edge of table or counter, or touch
hot surfaces.
10.Do not place on or near hot gas or
electric burners, or in a heated oven.
11.Unplug the unit when finished using.
12.Do not use appliance for other than
intended use.
13.Extreme caution must be exercised
when moving an appliance
containing hot oil or other hot
liquids.
14.To disconnect, turn PLATE SELECT
dial to OFF setting, then remove
plug from wall outlet.
NOTICE
This appliance has a polarized plug (one
blade is wider than the other) to reduce
the risk of electric shock. This plug will fit
in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse
the plug. If it still does not fit, contact a
qualified electrician. Do not modify the
plug in any way.
15.WARNING: TO REDUCE THE RISK
OF FIRE OR ELECTRIC SHOCK,
ONLY AUTHORIZED PERSONNEL
SHOULD DO REPAIRS.
3
a. Grill Side: Perfect for grilling steak,
burgers, chicken and vegetables.
CONTENTS
Important Safeguards............................ 3
Features and Benefits............................ 4
Getting to Know Your Control Panel..... 5
Before the First Use............................... 5
Assembly Instructions ........................... 5
The Griddler® Elite Positions ................. 6
Operating the Griddler® Elite................. 6
Operating the Timer............................... 8
Cleaning and Care................................. 9
User Maintenance.................................. 9
Storage................................................. 10
Troubleshooting Chart......................... 11
Warranty............................................... 12
b. Griddle Side: Prepare pancakes,
eggs, bacon and seared scallops.
5. Drip Tray
Collects grease and removes from base
for easy cleanup (dishwasher safe).
6. Cleaning/Scraping Tool
Helps clean grill and griddle plates
after cooking.
7. Plate Release Buttons
Push in to release and remove
cooking plates.
8. Hinge Release Lever
Allows the cover to extend back to
the Flat position.
FEATURES AND
BENEFITS
9. Cover Height Adjuster
Features 6 preset height positions
for top melting. Locks cover closed
to store.
1. Base and Cover
Solid construction with stainless steel
self-adjusting cover.
BPA Free (not shown)
All materials that come in contact
with food are BPA free.
2. Panini-Style Handle
Sturdy cast-metal handle adjusts cover
to accommodate thickness of food.
3. Control Panel
1
See page 5 for more details.
2
4. Removable, Reversible and
Embedded Cooking Plates
Nonstick and dishwasher safe for
easy cleanup.
3
6
4a
4b
5
8
7
7
9
4
GETTING TO KNOW YOUR CONTROL PANEL
a. Plate Select Dial & Temperature Dials
Use the PLATE SELECT dial to select
LOWER and UPPER plates and to turn
unit off. Use the UPPER and LOWER
temperature dials to select temperature
of each plate.
c. Upper and Lower Plate Sear Buttons
Press to sear at 500˚F for up to
two minutes.
d. Start/Stop Button
Starts/stops cooking selection.
e. Blue Backlit LCD Display
Shows plate temperatures, timer and
PREHEAT/READY.
b. Time Directionals
Use to set cooking time. Press and hold
to scroll quickly; press and release to
advance more slowly.
c
d
e
b
a
used for panini and other toasted
sandwiches.
BEFORE THE
FIRST USE
b. Griddle side: smooth surface
intended for cooking bacon and eggs,
pancakes and French toast. Also can
be used for panini and other toasted
sandwiches.
Remove all packaging materials and any
labels or stickers from your grill. Be sure
all parts (see Features and Benefits) have
been included before discarding any
packaging materials. You may want to
keep the box and packing materials for
use at a later date.
a.
b.
Before using your Cuisinart® Griddler® Elite
for the first time, remove any dust from
shipping by wiping the base, cover and
controls with a damp cloth. Thoroughly
clean cooking plates, drip tray and
scraping tool; all are dishwasher safe.
Refer to Assembly Instructions for
plate removal.
2. Identify the lower and upper plates. The
word LOWER or UPPER is embossed
on both sides of each plate.
3. Locate the connector prongs on the
plate(s) and line up with the appropriate
connection blocks. Slide the connector
prongs into the blocks and push down
the front end of the plate(s). They will
snap into place.
ASSEMBLY
INSTRUCTIONS
Place base on a clean, flat surface where
you intend to cook, with the controls
directly in front of you.
To insert the cooking plates:
1. Choose the side(s) you intend to cook
on. The two cooking plates each have
two sides:
NOTE: If the plate(s) are not inserted
properly and completely into the
connection blocks, the plate(s) will not
heat up. This is a safety feature that
prevents the user from operating the
a. Grill side: ribbed surface intended for
grilling steaks, hamburgers, chicken,
seafood and vegetables. Also can be
5
grill when it is not assembled correctly.
desired height, then slide the cover height
adjuster into a notch to set the position.
4. Slide the drip tray into the base at the
rear of the unit from the right side.
NOTE: After Closed Cooking, you can
lock the upper plate/cover back into place
by simply closing the unit without any
food in it.
FLAT COOKING Position – To Cook on
Full Grill, Full Griddle or Half Grill/Half
Griddle: Upper plate/cover opens to lie
flat, level with the lower plate/base.
To adjust to this position from the Preheat
position, open unit and slide the hinge
release lever up while pushing the handle
back. The upper plate/cover will sit flat,
resting on the handle.
5. Plug the cord into a standard electrical
outlet. The blue backlight on the LCD
screen will illuminate, indicating the unit
is energized. The LCD will display the
current settings.
To adjust to this position from Closed
Cooking position, first close the unit,
resting upper plate/cover flat on lower
plate/base. You will hear the upper plate
click into place. Open unit and slide the
hinge release lever up while pushing the
handle back. The upper plate/ cover will
sit flat, resting on the handle.
NOTE: If the START/STOP button is not
pressed within 10 minutes, the unit will
enter SLEEP mode. The blue backlight
on the LCD screen will turn off and the
screen’s display will go blank.
6. Just follow the instructions below
to position the unit, and you’re ready
to cook!
To adjust to this position from Open
Cooking position, grasp handle and pull
slightly forward, then slide the hinge
release lever up while pushing the handle
back. The upper plate/cover will sit flat,
resting on the handle.
GRIDDLER® ELITE
POSITIONS
STORAGE Position – Upper plate/cover
rests flat on the lower plate/base and
cover height adjuster is in Lock position.
OPERATING
PREHEAT Position – Upper plate/
cover rests flat on the lower plate/base
and cover height adjuster is in
Unlock position.
THE GRIDDLER® ELITE
Standard Cooking
1. Turn the PLATE SELECT dial to the
desired plate selection.
OPEN COOKING Position – To Cook on
Lower Plate Only: Lift the handle so upper
plate/cover is vertical. Plate does not
“float” in this position.
You can choose the upper plate,
lower plate, or both plates, depending
on how and what you want to cook.
We recommend the following plate
selections:
CLOSED COOKING Position –
To Contact Grill or Panini Press: Start
with unit in Open Cooking position.
Lower top carefully until plate contacts
food. Hinge will automatically release the
plate, allowing it to “float” and rest evenly
on food.
Cooking Option
Plate Selection
Contact Grill
Both
Panini Press
Both
Full Grill
Both
To Top Melt: Start with unit in Open
Cooking position. Wearing an oven mitt,
press down slightly on front of upper
plate/cover to release hinge, allowing
plate to “float.” Lower it to close to the
Full Griddle
Both
Half Grill and Half Griddle
Half Grill or Half Griddle
Top Melt
Both
Lower or Upper
Both
6
The selected plate(s) and the
corresponding temperature(s) will
appear on the LCD screen.
NOTE: If both plates are selected,
when the first plate reaches
temperature it will show READY and
the unit will beep 1 time; you can begin
cooking on this plate if you choose.
The second plate will continue to
preheat until it reaches temperature, at
which time it will show READY and the
unit will beep 3 times.
2. Turn the temperature dial for the
selected plate(s) to the desired setting
– from Warm to 450°F. The temperature
readout(s) in the LCD screen will
change as you turn the dial.
NOTE: Warm setting will display
as 200°F.
In the example below, the upper plate
temperature has been set to 250˚F and
is ready, and the lower plate
temperature has been set to 350˚F and
is still preheating.
In the example below, the lower plate
temperature has been set to 350˚F.
3. Once the desired temperature setting(s)
have been selected, press the START/
STOP button.
4. To change the temperature(s) at any
time during operation, simply turn the
temperature dial of the selected plate(s)
to the new setting.
NOTE: If the START/STOP button is not
pressed within 10 minutes, the unit will
enter sleep mode. Turn any knob or
press any button to reactivate the unit.
a. If the plate(s) are in PREHEAT mode,
they will continue to preheat to new
selection.
a. The LED light around the START/
STOP button will illuminate and the unit
will beep one time.
b. If the plate(s) are in READY mode
and the temperature(s) are lowered,
READY will remain on display as the
unit adjusts to the lower temperature(s).
b. In the LCD screen, PREHEAT will
appear and the selected temperature(s)
will flash as the plate(s) heat up. It may
take up to 20 minutes to reach
operating temperature, depending on
the temperature(s) selected.
c. If the plate(s) are in READY mode
and the temperature(s) is raised,
PREHEAT will display and the higher
selected temperature will flash as the
plate(s) heat up. Once the higher
temperature(s) is reached, READY will
display, the temperature(s) will stop
flashing, and the unit will beep 3 times.
5. To change the plate selection at any
time during operation, simply turn the
PLATE SELECT dial to the new
c. When the plate(s) reach temperature,
the selected temperature(s) will stop
flashing, READY will display, and the
unit will beep 3 times.
selection and adjust the plate(s)
temperature (if necessary). PREHEAT
will display for new selected plate(s)
and the temperature will flash as the
plate(s) heat up. Once the new
temperature(s) are reached, READY will
display, the temperature(s) will stop
flashing, and the unit will beep 3 times.
7
6. To stop the unit from heating, simply
press the START/STOP button.
cooking on this plate if you choose.
The second plate will continue to
preheat until it reaches temperature, at
which time it will show READY and the
unit will beep 3 times. In the example
below, both plate temperatures have
been set to SEAR and the upper plate
is ready while the lower plate is still
preheating.
NOTE: If the unit is on and heated for
more than 2 hours, it will automatically
shut off. This is a safety feature of the
Griddler® Elite.
SEAR Function
You can sear foods at 500°F for up to
2 minutes.
In the example shown below, both
plates have been set to SEAR, but only
the upper plate has reached SEAR
temperature. The lower plate is still
preheating.
1. Follow Standard Cooking, Step 1.
2. Press UPPER SEAR and/or LOWER
SEAR button to initiate SEAR function.
SEAR will appear in place of the
temperature(s) in the LCD screen.
In the example below, the lower plate
has been set to SEAR.
6. The 02:00 minute countdown timer will
flash ten times to allow enough time to
put the food on the plate(s).
3. Press the START/STOP button. The
LED light around the START/STOP
button will illuminate and the unit will
beep one time.
4. In the LCD screen, PREHEAT will
display and SEAR will flash while the
plate(s) heat up to 500°.
7. After 10 seconds, the 2-minute
countdown will begin. To sear for less
than 2 minutes, simply press the arrow
down button at any time during
10-second delay or countdown to
decrease the time. You cannot sear for
more than 2 minutes at a time.
5. When the plate(s) reach the SEAR
temperature, SEAR will stop flashing,
READY will display and the unit will
beep 3 times.
8. When the countdown is complete, the
unit will beep 3 times to indicate the
SEAR cycle has finished, and the unit
will adjust to the temperature(s)
selected on the corresponding
temperature knobs.
NOTE: If both plates are selected for
SEAR, when the first plate reaches
temperature it will show READY and
the unit will beep 1 time; you can begin
8
position and unplug the power cord
from the wall outlet. Allow the unit to
cool down for at least 30 minutes.
2. Use the cleaning/scraping tool to
remove any leftover food from the
cooking plate(s).
9. To cancel SEAR, press the SEAR
button(s) again and the unit will adjust
to the temperature(s) selected on the
corresponding temperature knobs.
3. Dispose of grease from the drip tray
once cooled.
4. Press the plate release buttons to
remove cooking plates from the
housing. Be sure that the plates have
cooled completely before handling
(at least 30 minutes).
OPERATING
THE TIMER
The 60-minute timer can be activated at
any time the unit is on, except in the
middle of a SEAR cycle.
1. Press the up or down arrow button to
initiate time-set mode. The LCD screen
will display a blinking 00:00.
2. Press the up and down arrows to add
or subtract time. Time can be set in
30-second intervals up to 10 minutes,
then 1-minute intervals up to 60
minutes. Press and hold the buttons to
scroll through time more quickly. Timer
will stop blinking and automatically
start to count down when no time-set
buttons have been pressed for 3
seconds.
5. Wipe down the plates to remove any
leftover food. The cooking plates, drip
tray and cleaning/scraping tool can be
cleaned by hand or on the top shelf of
the dishwasher. The housing base,
cover and control panel can be wiped
clean with a soft, dry cloth. For tough
stains, dampen cloth. Never use an
abrasive cleaner or harsh pad.
3. To add or subtract time during
countdown, simply press the up or
down arrow buttons.
USER MAINTENANCE
• The first time you use the Griddler®
Elite it may have a slight odor and may
smoke a bit. This is common to
4. When the countdown is complete,
the unit will beep 3 times.
appliances with nonstick surfaces.
5. To stop and reset the timer, press
and hold both the up and down arrow
buttons at the same time for 2
• Always exercise caution when handling
the Griddler® Elite during cooking.
Open and close the unit using the
handle only. Do not touch the arms or
top cover during or immediately after
cooking, as they become hot during
use. We recommend you wear oven
mitts when handling the Griddler® Elite
to prevent burns.
seconds. Timer will default to 00:00.
6. To turn the unit off, simply turn PLATE
SELECT dial to OFF.
NOTE: If timer is in use and either
SEAR button is pressed, the SEAR
cycle will override the previously
set timer.
• Never use metal utensils, which will
scratch the nonstick plates. Instead,
use wooden or heat-proof plastic
utensils.
CLEANING AND CARE
1. Once you have finished cooking, turn
the PLATE SELECT dial to the OFF
• Never leave plastic utensils in contact
with the hot grill plates. This includes
9
the cleaning tool that is included.
• In between recipes, use a wooden or
heat-proof plastic utensil to scrape
excess food buildup through grease
channels and into the drip tray. Wipe off
any residue with a paper towel before
proceeding with next recipe.
• Allow the Griddler® Elite to cool down
completely (at least 30 minutes) before
cleaning.
• Any other servicing should be
performed by an authorized service
representative.
STORAGE
• Wrap the power cord around the cord
storage clips at the back of the base.
• Store clean cooking plates and drip
tray in the unit.
• Lock unit closed by sliding the cover
height adjuster to the Lock position.
10
Troubleshooting Chart
Subject
Question
Answer/Solution
Check to make sure your unit is plugged into a
functional outlet.
Why won’t my unit turn on?
Contact Customer Service at 1-800-726-0190.
If the PLATE SELECT dial is not turned to ON
within 10 minutes of the unit being plugged in, the
Griddler® Elite will enter SLEEP mode. All lights will
turn off. Turn the PLATE SELECT dial to ON to
“wake up” the unit and operate the unit as normal.
It is possible the unit overheated. Wait for the unit
to cool down and try again. If it does not turn back
on, contact Customer Service at 1-800-726-0190.
Why is my unit turning itself off?
Power
If already cooking and you want to change the
temperature of the current plate selection, you do
not need to hit START/STOP button again. Doing
so will turn the unit off. Simply change the
temperature dial for the current plate selection and
the unit will adjust automatically.
If your Griddler® Elite is not turned off or if you do
not change any settings, it will shut off
automatically after 2 hours. This is a safety feature.
Confirm you have inserted the plates correctly into
the connection blocks. If the plates are not fitted
correctly and securely, they will not heat up. This is
a safety feature.
Why won’t the plates get hot?
Yes. To change temperature of your current plate
selection, simply turn the plate’s temperature dial
and the unit will adjust automatically. To change
your plate selection, simply turn the PLATE
SELECT dial and set your new temperature.
Can I change my temperature
or plate selection when the unit
is already cooking?
Yes. Simply press the SEAR button(s) and the
plates will preheat to sear temperature. We
recommend you take the food off during preheating
to SEAR. Once the SEAR cycle is complete, the
unit will revert back to previously selected
temperatures.
Programming
Can I sear when I’m
already cooking?
You can only sear for 2 minutes max. However if
you would like to sear for less than 2 minutes,
simply press the down arrow button.
Can I adjust my SEAR
cycle time?
Yes, all removable parts are dishwasher safe. Do
not immerse or put the base of the unit in the
dishwasher. Clean it and the control panel with a
clean damp cloth.
Are the parts and accessories
dishwasher safe?
Cleaning
Use the scraper tool provided to scrape off any
excess food buildup. Do not use metal utensils
to clean the plates as they can damage the
nonstick coating.
Food residue is sticking to the
plates. How do I clean them
without damaging them?
11
BEFORE RETURNING YOUR
CUISINART® PRODUCT
WARRANTY
If your Cuisinart® Griddler® Elite should prove
to be defective within the warranty period, we
will repair it, or if we think necessary, replace
it. To obtain warranty service, simply call our
toll-free number 1-800-726-0190 for addi-
tional information from our Customer Service
Representatives or send the defective product
to Customer Service at Cuisinart, 7811 North
Glen Harbor Blvd., Glendale, AZ 85307.
To facilitate the speed and accuracy of your
return, please enclose $10.00 for shipping and
handling of the product.
Please pay by check or money order
(California residents need only supply proof of
purchase and should call 1-800-726-0190 for
shipping instructions).
NOTE: For added protection and secure han-
dling of any Cuisinart product that is being
returned, we recommend you use a traceable,
insured delivery service. Cuisinart cannot be
held responsible for in-transit damage or for
packages that are not delivered to us. Lost
and/or damaged products are not covered
under warranty.
LIMITED THREE-YEAR
WARRANTY
This warranty is available to consumers only.
You are a consumer if you own a Cuisinart®
Griddler® Elite that was purchased at retail for
personal, family or household use. Except as
otherwise required under applicable law, this
warranty is not available to retailers or other
commercial purchasers or owners.
We warrant that your Cuisinart® Griddler®
Elite will be free of defects in materials and
workmanship under normal home use for 3
years from the date of original purchase.
We recommend that you visit our website,
www.cuisinart.com for a fast, efficient way to
complete your product registration. However,
product registration does not eliminate the
need for the consumer to maintain the original
proof of purchase in order to obtain the
warranty benefits. In the event that you do not
have proof of purchase date, the purchase
date for purposes of this warranty will be the
date of manufacture.
Please be sure to include your return address,
daytime phone number, description of the
product defect, product model # (located on
bottom of product), original date of purchase,
and any other information pertinent to the
product’s return.
Your Cuisinart® Griddler® Elite has been manu-
factured to the strictest specifications and has
been designed for use only in 120 volt outlets
and only with authorized accessories and
replacement parts.
This warranty expressly excludes any defects
or damages caused by attempted use of
this unit with a converter, as well as use with
accessories, replacement parts or repair ser-
vice other than those authorized by Cuisinart.
This warranty does not cover any damage
caused by accident, misuse, shipment or other
than ordinary household use. This warranty
excludes all incidental or consequential dam-
ages. Some states do not allow the exclusion
or limitation of these damages, so these exclu-
sions may not apply to you. You may also have
other rights, which vary from state to state.
Important: If the nonconforming product is to
be serviced by someone other than Cuisinart’s
Authorized Service Center, please remind the
servicer to call our Consumer Service Center
at 1-800-726-0190 to ensure that the problem
is properly diagnosed, the product is serviced
with the correct parts, and to ensure that the
product is still under warranty.
CALIFORNIA RESIDENTS ONLY
California law provides that for In-Warranty
Service, California residents have the option of
returning a nonconforming product (A) to the
store where it was purchased or (B) to another
retail store which sells Cuisinart products of
the same type.
The retail store shall then, at its discretion,
either repair the product, refer the consumer
to an independent repair facility, replace the
product, or refund the purchase price less the
amount directly attributable to the consumer’s
prior usage of the product. If the above two
options do not result in the appropriate relief
to the consumer, the consumer may then
take the product to an independent repair
facility if service or repair can be economically
accomplished. Cuisinart and not the consumer
will be responsible for the reasonable cost of
such service, repair, replacement, or refund for
nonconforming products under warranty.
California residents may also, according
to their preference, return nonconforming
products directly to Cuisinart for repair, or
if necessary, replacement, by calling our
Consumer Service Center toll-free at 1-800-
726-0190. Cuisinart will be responsible for the
cost of the repair, replacement, and shipping
and handling for such products
under warranty.
12
©2012 Cuisinart
150 Milford Road
East Windsor, NJ 08520
Printed in China
12CE123598
IB-11143
Other trademarks or service marks referred to herein are the
trademarks or service marks of their respective owners.
|