OPERATOR’s MANUAL
MANUAL DEL OPERADOR
19.2 VOLT cHAIN sAW
MOTOsIERRA DE 19,2 V
Model No.
315.341300
Número de modelo
315.341300
WARNING: To reduce the risk
of injury, the user must read and
understand the operator’s manual
before using this product.
ADVERTENcIA: Para reducir el
riesgo de lesiones, el usuario debe leer
y comprender el manual del operador
antes de usar este producto.
Customer Help Line: 1-800-932-3188
Teléfono de atención al consumidor: 1-800-932-3188
Sears, Roebuck and Co., 3333 Beverly Rd., Hoffman Estates, IL 60179 USA
save this manual for future reference
987000-680
05-01-09 (REV:02)
Guarde este manual para futuras consulta
GENERAL sAFETY RULEs
WARNING: Read and understand all in-
Keep handles dry, clean, and free of oil and
structions. Failure to follow all instructions listed
below may result in electric shock, fire, and/or
serious personal injury.
grease.
Do not operate a chain saw that is damaged,
improperly adjusted, or not completely and
securely assembled. Chain should stop turn-
ing when the trigger is released. If the chain
turns after the trigger has been released, have
the unit serviced by your nearest Craftsman
service dealer.
Check for damaged parts. Any part or guard
that has been damaged should be carefully
checked to determine that it will operate
properly and perform its intended function.
Check for alignment of moving parts, binding
of moving parts, breakage of parts, mounting,
and any other conditions that may affect its
operation. A guard or other part that is dam-
aged should be properly repaired or replaced
by an authorized service dealer unless other-
wise indicated elsewhere in this manual.
READ ALL INsTRUcTIONs
BAsIc sAFETY PREcAUTIONs
Do not operate a chain saw with one hand!
Use a firm grip with thumbs and fingers en-
circling the chain saw handles. Serious injury
to the operator, helpers, bystanders, or any
combination of these persons may result from
one-handed operation. A chain saw is intend-
ed for two-handed use.
Always be aware of what you are doing when
using the chain saw. Use common sense. Do
not operate the chain saw when you are tired,
ill, or under the influence of alcohol, drugs, or
medication.
Stay alert and pay attention to what you are
doing. Use common sense when using this
unit.
All chain saw service, other than the items
listed in the operation and maintenance sec-
tions, should be performed by your nearest
Craftsman service dealer.
Keep all parts of your body away from the
saw chain when the unit is running.
Always carry the chain saw by the front han-
dle with the unit stopped and the guide bar
and saw chain positioned to the rear. When
transporting your chain saw, use the appro-
priate chain cover.
Never let anyone use your chain saw who
has not received adequate instructions in its
proper use. This applies to rentals as well as
privately owned saws.
Do not use in the rain, snow or wet condi-
tions.
Always maintain a proper stance. Do not
overreach.
Do not adapt your powerhead to a bow guide
or use it to power any attachments or devices
not listed for the saw.
Do not cut vines and/or small underbrush.
sAFETY APPAREL
Before you start the unit, make sure the saw
Wear snug fitting clothing. Always wear
heavy, long pants, long sleeves, overalls,
jeans or chaps made of cut resistant mate-
rial or ones that contain cut resistant inserts.
Wear non-slip safety footwear. Wear non-slip
heavy duty gloves to improve your grip and
to protect your hands. Do not wear jewelry,
short pants, sandals, or go barefoot. Do not
wear loose fitting clothing, which could be
drawn into the motor or catch the chain or un-
derbrush. Secure hair so it is above shoulder
level.
chain is not contacting any object.
Stop the chain saw before setting it down. Do
not leave the unit running unattended.
To avoid accidental starting, never carry the
unit with your finger on the trigger.
Maintain the unit with care. Keep the cutting
edge sharp and clean for best performance
and to reduce the risk of injury. Follow in-
structions for lubricating and changing ac-
cessories. Inspect the battery charger cord
periodically, and if damaged, have it replaced
or repaired by an authorized service dealer.
3 - English
GENERAL sAFETY RULEs
Always wear eye protection with side shields
Use only the replacement guide bars and low
kickbackchainsspecifiedbythemanufacturer
for the saw.
marked to comply with ANSI Z87.1, along
with hearing and head protection.
With a basic understanding of kickback, you
can reduce or eliminate the element of sur-
prise. Sudden surprise contributes to acci-
dents.
Keep proper footing and balance at all times.
Do not cut above shoulder height or overreach
KIcKBAcK
See Figures 1 - 3.
WARNING: Kickback may occur when the
moving chain contacts an object at the upper
portion of the tip of the guide bar or when the
wood closes in and pinches the saw chain in
the cut. Contact at the upper portion of the
tip of the guide bar can cause the chain to
dig into the object and stop the chain for an
instant. The result is a lightning fast, reverse
reaction which kicks the guide bar up and
back toward the operator. If the saw chain is
pinched along the top of the guide bar, the
guide bar can be driven rapidly back toward
the operator. Either of these reactions can
cause loss of saw control which can result in
serious injury. Do not rely exclusively upon
the safety devices built into the saw. As a
chain saw user, you should take several steps
to keep your cutting jobs free from accident
or injury.
when cutting.
Follow the sharpening and maintenance in-
structions for the saw chain.
Push and Pull - This reaction force is always
opposite to the direction the chain is mov-
ing where wood contact is made. Thus, the
operator must be ready to control the PULL
when cutting on the bottom edge of the bar,
and PUSH when cutting along the top edge.
See Figure 3.
IN THE cUTTING/WORK AREA
Do not operate a chain saw in a tree, on a
ladder, rooftop or scaffold; this is extremely
dangerous.
The following precautions should be fol-
Keep ALL children, bystanders, visitors, and
animals out of the work area while starting or
cutting with the chain saw.
lowed to minimize kickback:
• Hold the saw firmly with both hands when
the motor is running. Place your right hand
on the rear handle and your left hand on the
front handle with your thumbs and fingers
encircling the chain saw handles. A firm grip
together with a stiff left arm will help you
maintain control of the saw if kickback oc-
curs.
• Make sure that the area in which you are cut-
ting is free from obstructions. Do not let the
nose of the guide bar contact a log, branch,
fence, or any other obstruction that could be
hit while you are operating the saw.
• Always cut with the unit running at full speed.
Fullysqueezethethrottletriggerandmaintain
a steady cutting speed.
• Use replacement parts such as low kickback
chain and special guide bars that reduce the
risks associated with rotational kickback.
NOTE: The size of the work area depends on
the job being performed as well as the size
tree or work piece involved. For example,
felling a tree requires a larger work area than
making bucking cuts.
Never start cutting until you have a clear work
area, secure footing, and a planned retreat
path from the falling tree. Cluttered area invite
injuries.
Do not expose the chain saw to rain.
Do not use the chain saw in damp or wet
locations.
Do not use the chain saw near flammable liq-
uids, gases, or in any type of explosive atmo-
sphere.
Use extreme caution when cutting small size
brush and saplings, because slender mate-
rial may catch the saw chain and be whipped
toward you or pull you off balance.
4 - English
GENERAL sAFETY RULEs
When cutting a limb that is under tension, be
UNDERsTANDING YOUR cHAIN sAW
sAFETY DEVIcEs
LOW KIcKBAcK sAW cHAIN
alert for spring back so that you will not be
struck when the tension in the wood fibers is
released.
The rakers (depth gauges) ahead of each cutter
can minimize the force of a kickback reaction by
preventing the cutters from digging in too deeply
at the kickback zone. Only use replacement chain
that is equivalent to original chain or has been
certified as low kickback chain per ANSI B175.1.
Do not force the chain saw. The job can be
performed better and safer at the rate for
which it was intended.
Always use the right product for your applica-
tion. The chain saw should be used for cutting
wood only. Never use the chain saw to cut
plastic, masonry or non-wood building mate-
rials.
Low kickback saw chain is chain that has met the
kickbackperformancerequirementsofANSIB175.1
- 1991 (American National Standard for Power
Tools - Gasoline-Powered Chain Saws-Safety
Requirements) when tested on the representative
sample of chain saws below 3.8 c.i.d. specified in
ANSI B175.1 - 1991.
Do not use the chain saw for purposes not
intended.
Store idle chain saw when not in use. Chain
saw should be stored in a dry and high or
locked area out of the reach of children.
When storing chain saw, remove battery and
place the chain cover on the bar and chain.
Remove the battery pack from the chain saw
before cleaning, servicing, storing, transport-
ing, removing material from the unit, chang-
ing accessories such as the bar and chain, or
when not in use.
As saw chains are sharpened during their useful
life, they lose some of the low kickback qualities
and extra caution should be used.
GUIDE BARs
Generally, guide bars with small radius tips have
somewhat lower kickback potentials.
When making a replacement, be sure to order one
of the Craftsman bars listed for the saw in this
operator’s manual.
5 - English
sPEcIFIc sAFETY RULEs
Do not crush, drop or damage battery pack.
BATTERY sAFETY
Do not use a battery pack or charger that
has been dropped or received a sharp blow.
A damaged battery is subject to explosion.
Properly dispose of a dropped or damaged
battery immediately.
Battery operated units do not have to be
plugged into an electrical outlet; therefore,
they are always in operating condition. Be
aware of possible hazards even when unit is
not operating.
Batteries can explode in the presence of a
source of ignition, such as a pilot light. To re-
duce the risk of serious personal injury, never
use any cordless product in the presence of
open flame. An exploded battery pack can
propel debris and chemicals. If exposed, flush
with water immediately.
Do not charge unit in a damp or wet location.
Following this rule will reduce the risk of elec-
tric shock.
For best results, your battery unit should be
charged in a location where the temperature
is more than 50°F but less than 100°F. Do not
store outside or in vehicles.
Under extreme usage or temperature con-
ditions, battery pack leakage may occur. If
liquid comes in contact with your skin, wash
immediately with soap and water, then neu-
tralize with lemon juice or vinegar. If liquid
gets into your eyes, flush them with clean
water for at least 10 minutes, then seek im-
mediate medical attention.
Remove the battery pack from the chain saw
before cleaning, servicing, storing, transport-
ing, removing material from the unit, chang-
ing accessories such as the bar and chain, or
when not in use.
A battery pack must be recharged only with
the specified charger for the battery pack. A
charger that may be suitable for one type of
battery pack may create a risk of fire when
used with another battery pack. Use battery
pack only with charger listed.
Use battery only with charger listed.
BATTERY PAcK
MODEL
cHARGER
(Li-ion)
315.113740
(130285003)
(Multi-chemistry)
315.259260
315.113710
(130156001)
(140351001)
BATTERY PAcK
(Ni-cd)
315.341300
315. 259260
(140351001)
Do not dispose of batteries in a fire. The cell
may explode. Batteries should be recycled,
consult your local waste authority for infor-
mation regarding available recycling and/or
disposal options.
1425301 (911041)
130279003,
130279005
(Item No. 11375)
315.115730
(140301003)
9
When battery pack is not in use, keep it away
from other metal objects like: paper clips,
coins, keys, nails, screws, or other small met-
al objects that can make a connection from
one terminal to another. Shorting the battery
pack terminals together may cause sparks,
burns, or a fire.
To reduce the risk of explosion and possible
injury, Do not place battery units or their bat-
teries near fire or heat.
Do not open or mutilate the battery pack. Re-
leased electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
sAVE THEsE INsTRUcTIONs
6 - English
GLOssARY OF TERMs
Bar Tip Guard
Kickback, Rotational
An attachment that may be provided on the end
of the guide bar to prevent the chain at the end of
the guide bar from contacting the wood.
The rapid upward and backward motion of the
saw which can occur when the moving saw chain
near the upper portion of the tip of the guide bar
contacts an object, such as a log or branch.
Bucking
The process of cross cutting a felled tree or log
into lengths.
Low-Kickback chain
A chain that complies with the kickback
performance requirements of ANSI B175.1-1991
when tested on a representative sample of chain
saws.
chain Brake
A device used to stop the chain saw.
chain saw Powerhead
A chain saw without the saw chain and guide
bar.
Normal cutting Position
Those positions assumed in performing the
bucking and felling cuts.
Notching Undercut
A notch cut in a tree that directs the tree’s fall.
Oiler control
A system for oiling the guide bar and saw chain.
Rear Handle
clutch
A mechanism for connecting and disconnecting
a driven member to and from a rotating source of
power.
Drive sprocket or sprocket
The toothed part that drives the saw chain.
The support handle located at or toward the rear
of the saw.
Reduced Kickback Guide Bar
A guide bar which has been demonstrated to
reduce kickback significantly.
Replacement saw chain
Felling
The process of cutting down a tree.
Felling Back cut
The final cut in a tree felling operation made on
the opposite side of the tree from the notching
undercut.
A chain that complies with the kickback
performance requirements of ANSI B175.1-1991
when tested with specific chain saws. It may not
meet the ANSI performance requirements when
used with other saws.
Front Handle
The support handle located at or toward the front
of the chain saw.
Front Handle Guard
A structural barrier between the front handle of
a chain saw and the guide bar, typically located
close to the hand position on the front handle and
sometimes employed as an activating lever for a
chain brake.
saw chain
A loop of chain having cutting teeth, that cut
the wood, and that is driven by the motor and is
supported by the guide bar.
spiked Bumper (spike)
Guide Bar
The pointed tooth or teeth for use when felling or
bucking to pivot the saw and maintain position
while sawing.
A solid railed structure that supports and guides
the saw chain.
Kickback
switch
The backward or upward motion, or both of the
guide bar occurring when the saw chain near the
nose of the top area of the guide bar contacts
any object such as a log or branch, or when the
wood closes in and pinches the saw chain in the
cut.
A device that when operated will complete or
interrupt an electrical power circuit to the motor
of the chain saw.
switch Linkage
The mechanism that transmits motion from a
trigger to the switch.
switch Lockout
A movable stop that prevents the unintentional
operation of the switch until manually actuated.
Kickback, Pinch
The rapid pushback of the saw which can occur
when the wood closes in and pinches the moving
saw chain in the cut along the top of the guide
bar.
7 - English
sYMBOLs
The following signal words and meanings are intended to explain the levels of risk associated with
this product.
sYMBOL
sIGNAL
MEANING
Indicates an imminently hazardous situation, which, if not avoided,
will result in death or serious injury.
DANGER:
Indicates a potentially hazardous situation, which, if not avoided,
could result in death or serious injury.
WARNING:
cAUTION:
cAUTION:
Indicates a potentially hazardous situation, which, if not avoided,
may result in minor or moderate injury.
(Without Safety Alert Symbol) Indicates a situation that may result
in property damage.
Some of the following symbols may be used on this product. Please study them and learn their
meaning. Proper interpretation of these symbols will allow you to operate the product better and
safer.
sYMBOL
NAME
DEsIGNATION/EXPLANATION
Safety Alert
Indicates a potential personal injury hazard.
To reduce the risk of injury, user must read and
understand operator’s manual before using this
product.
Read The Operator’s
Manual
Wet Conditions Alert
Do not expose to rain or use in damp locations.
Always wear eye protection with side shields marked to
comply with ANSI Z87.1, along with hearing and head
protection.
Wear Eye, Hearing, and
Head Protection
Operate With Two
Hands
Hold and operate the saw properly with both hands.
Do not operate the saw using only one hand.
One Handed
Kickback
DANGER! Beware of kickback.
Avoid bar nose contact.
Bar Nose Contact
Wear Gloves
Wear non-slip, heavy-duty protective gloves when
handling the chain saw.
8 - English
sYMBOLs
Wear non-slip safety footwear when using this
equipment.
Wear Safety Footwear
Keep Bystanders
Away
Keep all bystanders and animals at least 50 ft. away.
Pour bar and chain lubricant into oil tank where
indicated. Do not use any other fluids.
Oil Indicator
This product uses lithium-ion or nickel-cadmium
batteries. Local, state or federal laws may prohibit
disposal of batteries in ordinary trash. Consult your
local waste authority for information regarding available
recycling and/or disposal options.
Recycle Symbols
Li - Ion
V
Volts
Voltage
Direct Current
Type or a characteristic of current
FEATUREs
PRODUcT sPEcIFIcATIONs
Motor...............................................19.2 Volt DC
KNOW YOUR cHAINsAW
See Figure 4.
The safe use of this product requires an
understanding of the information on the product
and in this operator’s manual as well as a
knowledge of the project you are attempting.
Before use of this product, familiarize yourself with
all operating features and safety rules.
Bar Length.................................................. 10 in.
Replacement Bar
Part Number.................................. 671834006
Replacement Chain
Part Number...............6958301 or 690583002
NOTE: This saw was designed for occasional
light duty use and has some limitations as to
what it can cut.
9 - English
AssEMBLY
PAcKING LIsT
Chain Saw with Chain Cover
Wrench
UNPAcKING
This product has been shipped completely as-
sembled.
Carefully remove the product and any acces-
sories from the box. Make sure that all items
listed in the packing list are included.
Battery Pack
Charger
Operator’s Manual
WARNING: Do not use this product if it is not
completely assembled or if any parts appear
to be missing or damaged. Use of a product
that is not properly and completely assem-
bled could result in serious personal injury.
WARNING: If any parts are damaged or
missing do not operate this product until the
parts are replaced. Using the saw with dam-
aged or missing parts could result in serious
personal injury.
Inspect the product carefully to make sure no
breakage or damage occurred during ship-
ping.
Do not discard the packing material until you
have carefully inspected and satisfactorily oper-
ated the product.
WARNING: Do not attempt to modify this
product or create accessories not recom-
mended for use with this product. Any such
alteration or modification is misuse and
could result in a hazardous condition lead-
ing to possible serious personal injury.
If any parts are damaged or missing, please call
1-800-932-3188 for assistance.
WARNING: To prevent accidental starting
that could cause serious personal injury,
always remove the battery pack from the
product when assembling parts.
OPERATION
Before each use, inspect the entire product for
damaged, missing, or loose parts such as screws,
nuts, bolts, caps, etc. Tighten securely all fasteners
and caps and do not operate this product until all
missing or damaged parts are replaced. Please
call 1-800-932-3188 or contact an authorized
service center for assistance.
WARNING: Do not allow familiarity with
this product to make you careless. Remember
that a careless fraction of a second is sufficient
to inflict serious injury.
WARNING: Always wear eye protection
with side shields marked to comply with ANSI
Z87.1, along with hearing and head protection.
Failure to do so could result in objects being
thrown into your eyes and other possible
serious injuries.
APPLIcATIONs
You may use this product for the following
purposes:
Limbing and pruning branches from trees
Felling small trees up to 5 in. diameter
Bucking the fallen tree into shorter lengths
This product will accept Craftsman 19.2 V lithium-
ion battery packs and Craftsman 19.2 V nickel-
cadmium battery packs.
WARNING: Do not use any attachments
or accessories not recommended by the
manufacturer of this product. The use of
attachments or accessories not recommended
can result in serious personal injury.
10 - English
OPERATION
For complete charging instructions, refer to the
Operator’s Manual for your Craftsman battery pack
and charger models.
NOTE: Do not use dirty, used or otherwise
contaminated lubricants. Damage may occur
to the bar or chain.
Carefully pour the bar and chain lubricant into
TO INsTALL / REMOVE BATTERY PAcK
the tank.
See Figure 5.
Check and fill the oil tank when battery is
recharged, or as needed.
WARNING: Always remove battery pack
from your tool when you are assembling
parts, making adjustments, cleaning, carrying,
transporting or when not in use. Removing
battery pack will prevent accidental starting that
could cause serious personal injury.
Depress the oil tank cap several times to
pump the lubricant to the chain before
starting the saw.
Depress the oil tank cap every 20-30 seconds
while cutting to keep the chain lubricated.
NOTE: It is normal for lubricant to seep from the
saw when not in use. To prevent seepage, empty
the oil tank after each use. When storing the unit
for a long period of time (three months or longer) be
sure the chain is lightly lubricated; this will prevent
rust on the chain and bar sprocket.
NOTE: To avoid serious personal injury, always
remove the battery pack and keep hands clear of
the lock-out button when carrying or transporting
the tool.
To install:
Place the battery pack in your chain saw.
Align raised rib on battery pack with groove in
chain saw’s battery port.
sTARTING AND sTOPPING THE cHAIN
sAW
See Figure 7.
Make sure the latches on each side of
the battery pack snap in place and that
battery pack is secured in chain saw before
beginning operation.
WARNING: Keep body to the left of the
chain line. Never straddle the saw or chain, or
lean over past the chain line.
To remove:
starting the chain saw:
Locate latches on side of battery pack and depress
both sides to release the battery pack from the
chain saw.
Place the chain saw on a flat bare surface
and make sure no objects or obstructions
are in immediate vicinity which could come in
contact with the bar and chain.
cAUTION: When placing battery pack in your
chain saw, be sure raised rib on battery pack
aligns with groove in chain saw’s battery port
and latches snap in place properly. Improper
assembly of battery pack can cause damage
to internal components.
Press and hold the trigger lock-out button.
This makes the trigger operational.
Press and hold the trigger, release the trigger
lock-out button and continue to squeeze the
trigger for continued operation.
stopping the chain saw:
Release the trigger to stop the chain saw.
Upon release of the trigger, the trigger lock-
out button will be automatically reset to the
lock position.
cAUTION: Remove battery pack from unit.
Fill oil tank with Craftsman Bar and Chain
Lubricant before starting the chain saw. Failure
to lubricate the chain will cause damage to the
bar and chain.
This cordless chain saw is not designed for cutting
trees larger than 5 in. in diameter.
cHAIN OIL sYsTEM
See Figure 6.
This cordless chain saw is designed for
limbing and pruning type cutting, as well
as cutting trees up to 5 in. in diameter only.
Use Craftsman Bar and Chain Lubricant.
It is formulated to perform over a wide
temperature range with no dilution required.
11 - English
OPERATION
Squeeze the trigger and let the chain
PREPARATION FOR cUTTING
accelerate to full speed before entering the
cut.
PROPER GRIP ON HANDLEs
See Figures 8 - 10.
Begin cutting with the saw against the log.
Refer to General SaFety ruleS earlier in this
manual for appropriate safety equipment.
Keep the unit running the entire time you are
cutting, maintain a steady speed.
Wear non-slip gloves for maximum grip and
Allow the chain to cut for you; exert only light
downward pressure. If you force the cut,
damage to the bar, chain, or unit can result.
Release the trigger as soon as the cut is
completed, allowing the chain to stop. If
you run the saw without a cutting load,
unnecessary wear can occur to the chain,
bar, and unit.
protection.
Hold the saw firmly with both hands. Always
keep your left hand on the front handle and
your right hand on the rear handle so that
your body is to the left of the chain line.
WARNING: Never use a left-handed (cross-
handed) grip, or any stance which would place
your body or arm across the chain line.
Do not put pressure on the saw at the end of
the cut.
Maintain a proper grip on the saw whenever
the unit is running. The fingers should encircle
the handle and the thumb is wrapped under
the handlebar. This grip is least likely to
be broken (by a kickback or other sudden
reaction of the saw). Any grip in which the
thumb and fingers are on the same side of the
handle, is dangerous because a slight kick of
the saw can cause loss of control.
WORK AREA PREcAUTIONs
Cut only wood or materials made from wood,
no sheet metal, no plastics, no masonry, no
non-wood building materials.
Never allow children to operate the saw.
Allow no person to use this chain saw who
has not read this Operator’s Manual or
received adequate instructions for the safe
and proper use of this chain saw.
When felling a tree, keep everyone - helpers,
bystanders, children, and animals - a safe
distance from the cutting area. During felling
operations, the safe distance should be a
least twice the height of the largest trees in
the felling area. During bucking operations,
keep a minimum distance of 15 feet between
workers.Trees should not be felled in a
manner that would endanger any person,
strike any utility line or cause any property
damage. If the tree does make contact with
any utility line, the utility company should be
notified immediately.
WARNING: Do not operate the throttle
trigger with your left hand and hold the front
handle with your right hand. Never allow any
part of your body to be in the chain line while
operating a saw.
PROPER cUTTING sTANcE
See Figure 11.
Weight should be balanced with both feet on
solid ground.
Keep left arm with elbow locked in a “straight
arm” position to withstand any kickback
force.
Always cut with both feet on solid ground to
prevent being pulled off balance.
Your body should always be to the left of the
chain line.
Do not cut above shoulder height, as a saw
held higher is difficult to control against
kickback forces.
Do not fell trees near electrical wires
or buildings. Leave this operation for
professionals.
Thumb should be on underside of handlebar.
BAsIc cUTTING PROcEDURE
Practice cutting a few small logs using the following
technique to get the “feel” of using the saw before
you begin a major sawing operation.
Cut only when visibility and light are adequate
Take the proper stance in front of the wood
for you to see clearly.
with the saw off.
12 - English
OPERATION
Before any cuts are started, pick your escape
TREE FELLING
route (or routes in case the intended route is
blocked); clear the immediate area around the
tree and make sure there are no obstructions
in your planned path of retreat. Clear path
of safe retreat approximately 135° from
planned line of fall. The retreat path should
extend back and diagonally to the rear of the
expected line of fall. See Figure 12.
See Figures 12-16.
Unusual Hazardous Tree Felling conditions
Do not fell trees during periods of high wind or
heavy precipitation. Wait to do your cutting until
the hazard has ended.
WARNING: Do not cut down trees having
an extreme lean or large trees that have rotten
limbs, loose bark, or hollow trunks. Have these
trees pushed or dragged down with heavy
equipment, then cut them up.
Before felling is started, consider the force
and direction of the wind, the lean and
balance of the tree, and the location of large
limbs. These things influence the direction in
which the tree will fall. Do not try to fell a tree
along a line different from its natural line of
fall.
The chain saw operator should keep on the
uphill side of the terrain as the tree is likely to
roll or slide downhill after it is felled.
WARNING: Electrocution hazard. Do
not cut trees or branches near power lines or
electrical wires. Contact with power lines or live
electrical wires will result in serious personal
injury or possible death.
Remove dirt, stones, loose bark, nails,
staples, and wire from the tree where felling
cuts are to be made.
WARNING: Do not cut trees or branches
near buildings, which may result in serious
injuries or property damage.
Notched Undercut. Cut a notch about 1/3
the diameter of the tree, perpendicular to the
direction of fall. Make the cuts of the notch so
they intersect at a right angle to the line of fall.
This notch should be cleaned out to leave a
straight line. To keep the weight of the wood
off the saw, always make the lower cut of the
notch before the upper cut. See Figure 14.
Felling Backcut. The backcut is always made
level and horizontal, and at a minimum of 2
in. above the horizontal cut of the notch. See
Figures 14 - 15.
WARNING: Check the tree for damaged
or dead branches that could fall and hit you
during felling.
WARNING: Periodically glance at the top
of the tree during the backcut to assure the tree
is going to fall in the desired direction.
WARNING: If the tree starts to fall in the
wrong direction, or if the saw gets caught or
hung up during the fall, leave the saw and save
yourself!
Never cut through to the notch. Always
leave a band of wood between the notch
and backcut (approximately 2 in. or 1/10 the
diameter of the tree). This is called “hinge” or
“hingewood.” It controls the fall of the tree
and prevents slipping or twisting or shoot-back
of the tree off the stump. See Figures 14 - 15.
On large diameter trees, stop the back cut
before it is deep enough for the tree to either
fall or settle back on the stump. Then insert
soft wooden or plastic wedges into the cut so
they do not touch the chain. The wedges can
be driven in, little by little, to help jack the tree
over. See Figure 16.
Felling a tree - When bucking and felling
operations are being performed by two or more
persons, at the same time, the felling operation
should be separated from the bucking
operation by a distance of at least twice the
height of the tree being felled. Trees should
not be felled in a manner that would endanger
any person, strike any utility line or cause any
property damage. If the tree does make contact
with any utility line, the utility company should
be notified immediately.
13 - English
OPERATION
When the log is supported on one end, cut 1/3
As tree starts to fall, stop the chain saw
and put it down immediately. Retreat along
the cleared path, but watch the action in
case something falls your way. Be alert for
overhead limbs or branches that may fall and
watch your footing.
the diameter from the underside or underbucking.
Then make the finishing cut by overbucking to
meet the first cut.
As the log is being cut, it will tend to bend. The
saw can become pinched or hung in the log if you
make the first cut deeper than 1/3 of the diameter
of the log.
Give special attention to logs under stress to
prevent the bar and chain from pinching.
When bucking on a slope, always stand on the
uphill side of the log as shown in figure 18. When
“cutting through,” to maintain complete control
of the chain saw, release the cutting pressure near
the end of the cut without relaxing your grip on the
chain saw handles. Do not let the chain contact
the ground. After completing the cut, wait for the
saw chain to stop before you move the chain saw.
Always stop the motor before moving from tree
to tree.
WARNING: Never cut through to the notch
when making a backcut. The hinge controls
the fall of the tree, this is the section of wood
between the notch and backcut.
BUcKING
See Figures 17 - 20.
Bucking is the term used for cutting a fallen tree
to the desired log length.
Always make sure your footing is secure and
your weight is distributed evenly on both feet.
Cut only one log at a time.
Support small logs on a saw horse or another
TYPEs OF cUTTING UsED
log while bucking.
See Figure 20.
Keep a clear cutting area. Make sure that no
objects can contact the guide bar nose and
chain during cutting, this can cause kickback.
Refer to Precautions Against Kickback
earlier in this manual.
OVERBUcKING
Begin on the top side of the log with the bottom
of the saw against the log; exert light pressure
downward. Note that the saw will tend to pull
away from you.
When bucking on a slope, always stand
on the uphill side of the log. To maintain
complete control of the chain saw when
cutting through the log, release the cutting
pressure near the end of the cut without
relaxing your grip on the chain saw handles.
Do not let the chain contact the ground. After
completing the cut, wait for the saw chain to
stop before you move the chain saw. Always
stop the motor before moving from tree to
tree.
Sometimes it is impossible to avoid pinching
(with just standard cutting techniques) or
difficult to predict which way a log will settle
when cut. To avoid pinching while cutting,
rotate or move the log so that the pinch is
eliminated.
UNDERBUcKING
Begin on the under side of the log with the top
of the saw against the log; exert light pressure
upward. During underbucking, the saw will tend
to push back at you. Be prepared for this reaction
and hold the saw firmly to maintain control.
WARNING: Never climb into a tree to limb
or prune. Do not stand on ladders, platforms, a
log, or in any position which can cause you to
lose your balance or control of the saw.
LIMBING
See Figure 21.
Limbing is removing branches from a fallen tree.
Work slowly, keeping both hands on the
chain saw with a firm grip. Always make sure
your footing is secure and your weight is
distributed evenly on both feet.
BUcKING LOGs UNDER sTREss
See Figures 19 - 20.
When the log is supported along its entire length,
it should be cut from the top or overbucking.
Leave the larger support limbs under the tree
to keep the tree off the ground while cutting.
14 - English
OPERATION
Limbs should be cut one at a time. Remove Your second cut should overbuck to drop the
the cut limbs from the work area often to help
keep the work area clean and safe.
branch off.
Now make your finishing cut smoothly and
neatly against the main member so the bark
will grow back to seal the wound.
Branches under tension should be cut from
the bottom up to avoid binding the chain saw.
Keep the tree between you and the chain saw
while limbing. Cut from the side of the tree
opposite the branch you are cutting.
WARNING: If the limbs to be
pruned are above shoulder height, hire
a professional to perform the pruning.
PRUNING
See Figure 22.
Pruning is trimming limbs from a live tree.
sPRINGPOLEs
See Figure 23.
Work slowly, keeping both hands on the
chain saw with a firm grip. Always make sure
your footing is secure and your weight is
distributed evenly on both feet.
Do not cut from a ladder, this is extremely
dangerous. Leave this operation for
professionals.
Do not cut above shoulder height as a saw
held higher is difficult to control against
kickback.
A springpole is any log, branch, rooted stump, or
sapling which is bent under tension by other wood
so that it springs back if the wood holding it is cut
or removed. On a fallen tree, a rooted stump has
a high potential of springing back to the upright
position during the bucking cut to separate the log
from the stump. Watch out for springpoles, they
are dangerous.
WARNING: Springpoles are dangerous and
could strike the operator, causing the operator
to lose control of the chain saw. This could
result in severe or fatal injury to the operator.
When pruning trees it is important not to
make the finishing cut next to the main limb
or trunk until you have cut off the limb further
out to reduce the weight. This prevents
stripping the bark from the main member.
Underbuck the branch 1/3 through for your
first cut.
15 - English
MAINTENANcE
BATTERIEs
WARNING: When servicing, use only
identical replacement parts. Use of any other
parts may create a hazard or cause product
damage.
This product will accept Craftsman® 19.2 V
lithium-ion battery packs and Craftsman 19.2 V
nickel-cadmium battery packs.
The batteries for this product have been designed
to provide maximum trouble-free life. However,
like all batteries, they will eventually wear out.
Do not disassemble battery pack and attempt to
replace the batteries. Handling of these batteries,
especially when wearing rings and jewelry, could
result in a serious burn.
WARNING: Always wear eye protection
with side shields marked to comply with ANSI
Z87.1, along with hearing and head protection.
Failure to do so could result in objects being
thrown into your eyes and other possible seri-
ous injuries. If operation is dusty, also wear
breathing protection.
To obtain the longest possible battery life, we
suggest the following:
For lithium-ion batteries:
WARNING: To avoid serious personal
injury, always remove the battery pack from
the product when cleaning or performing any
maintenance.
Remove the battery pack from the charger
once it is fully charged and ready for use.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature
is below 80°F and away from moisture.
GENERAL MAINTENANcE
Store battery packs in a 30%-50% charged
Before each use, inspect the entire product for
damaged, missing, or loose parts such as screws,
nuts, bolts, caps, etc. Tighten securely all fasteners
and caps and do not operate this product until all
missing or damaged parts are replaced. Please
call 1-800-932-3188 or contact an authorized
service center for assistance.
condition.
Every six months of storage, charge the pack
as normal.
For nickel-cadmium batteries:
Remove the battery pack from the charger
once it is fully charged and ready for use.
For battery pack storage longer than 30 days:
Avoid using solvents when cleaning plastic parts.
Most plastics are susceptible to damage from
various types of commercial solvents and may be
damaged by their use. Use clean cloths to remove
dirt, dust, oil, grease, etc.
Store the battery pack where the temperature
is below 80°F.
Store battery packs in a “discharged” condi-
tion.
BATTERY PAcK REMOVAL AND
PREPARATION FOR REcYcLING
WARNING: Do not at any time let brake
fluids, gasoline, petroleum-based products,
penetrating oils, etc., come in contact with plas-
tic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious
personal injury.
WARNING: Upon removal, cover the bat-
tery pack’s terminals with heavy-duty adhesive
tape. Do not attempt to destroy or disassemble
battery pack or remove any of its components.
Lithium-ion and nickel-cadmium batteries must
be recycled or disposed of properly. Also, never
touch both terminals with metal objects and/
or body parts as short circuit may result. Keep
away from children. Failure to comply with
these warnings could result in fire and/or seri-
ous injury.
Only the parts shown on the parts list are intended
to be repaired or replaced by the customer. All
other parts should be replaced at an Authorized
Service Center.
16 - English
MAINTENANcE
REcOMMENDED BAR AND cHAIN
cOMBINATIONs
REPLAcING BAR AND cHAIN
See Figures 24 - 28.
Bar Part Number - 10 in.
WARNING: Remove the battery pack from
the chain saw and make sure the chain has
stopped before you do any work or making
any adjustments on the saw. Failure to do so
may result in accidental starting and possible
serious injury.
671834006
chain Part Number
6958301 or 690583002
Replace the chain cover, washer and chain
cover screw. Tighten the chain cover screw
finger tight only. The bar must be free to
move for tension adjustment.
WARNING: The safety instructions in this
section are to protect the user from serious
personal injury.
Remove all the slack from the chain by turn-
ing the chain tensioning screw clockwise until
the chain seats snugly against the bar with
the drive links in the bar groove.
WARNING: Always wear gloves when han-
dling the bar and chain; these components are
sharp and may contain burrs.
Lift the tip of the guide bar up to check for
sag. Release the tip of the guide bar and turn
the chain tensioning screw 1/2 turn clock-
wise. Repeat this process until sag does not
exist.
WARNING: Never touch or adjust the chain
while the motor is running. The saw chain is
very sharp; always wear protective gloves when
performing maintenance to the chain to avoid
possible serious lacerations.
Hold the tip of the guide bar up and tighten
the bar mounting screw securely.
Chain is correctly tensioned when there is no
sag on the underside of the guide bar, the
chain is snug, but it can be turned by hand
without binding.
Remove the battery pack before you do any
NOTE: If chain is too tight, it will not rotate.
Loosen the chain cover screw slightly and
turn tension adjuster 1/4 turn counterclock-
wise. Lift the tip of the guide bar up and
retighten chain cover screw securely. Assure
that the chain will rotate without binding.
work on the chain saw.
Remove the hex key from the storage area
and use it to remove the chain cover screw,
washer and chain cover from the chain saw.
Remove the bar and chain from the mounting
surface.
Place the hex key back into the storage area.
Remove the old chain from the bar.
Lay out the new saw chain in a loop and
straighten any kinks. The cutters should face
in the direction of chain rotation. If they face
the opposite direction, turn the loop over.
Place the chain drive links into the bar groove.
Position the chain so there is a loop at the
back of the bar. Hold the chain in position on
the bar and place the loop around the sprock-
et of the chain saw. Fit the bar flush against
the mounting surface so that the bar stud is in
the long slot of the bar.
cHAIN TENsION
See Figures 29 - 30.
Stop the motor before setting the chain ten-
sion. Make sure the guide bar screw is loos-
ened to finger tight, turn the chain tensioner
clockwise to tension the chain. Refer to Re-
placing Bar and chain earlier in this manual
for additional information.
A cold chain is correctly tensioned when there
is no slack on the underside of the guide bar,
the chain is snug, but it can be turned by
hand without binding.
NOTE: When placing the bar on the bar stud,
assure that the adjusting pin is in the chain
tension pin hole.
Chain must be re-tensioned whenever the
flats on the drive links hang out of the bar
groove.
17 - English
MAINTENANcE
HOW TO sHARPEN THE cUTTERs
During normal saw operation, the temperature
of the chain will increase. The drive links of a
correctly tensioned warm chain will hang ap-
proximately .050 in. out of the bar groove.
NOTE: New chain tends to stretch, check chain
tension frequently and tension as required.
See Figures 33 - 34.
Be careful to file all cutters to the specified angles
and to the same length, as fast cutting can be
obtained only when all cutters are uniform.
Wear gloves for protection. Properly tension
the chain prior to sharpening. Refer to chain
Tension section earlier in this manual. Do all
of your filing at the mid-point of the bar.
cAUTION: Chain tensioned while warm, may
be too tight upon cooling. Check the “cold ten-
sion” before next use.
Use a 5/32 in. diameter round file and holder.
Keep the file level with the top plate of the
tooth. Do not let the file dip or rock.
cHAIN MAINTENANcE
Using light but firm pressure, stroke towards
See Figures 31 - 32.
the front corner of the tooth.
Lift file away from the steel on each return
WARNING: Remove the battery pack and
make sure the chain has stopped before you
do any work or making any adjustments on the
saw. Failure to do so may result in accidental
starting and possible serious injury.
stroke.
Put a few firm strokes on every tooth. File all
left hand cutters in one direction. Then move
to the other side and file the right hand cut-
ters in the opposite direction. Occasionally
remove filings from the file with a wire brush.
Use only low-kickback chain on this saw. This
fast-cutting chain will provide kickback reduction
when properly maintained.
For smooth and fast cutting, chain needs to be
maintained properly. The chain requires sharpen-
ing when the wood chips are small and powdery,
the chain must be forced through the wood during
cutting, or the chain cuts to one side. During main-
tenance of your chain, consider the following:
WARNING: Improper chain sharpening
increases the potential of kickback.
WARNING: Failure to replace or repair
damaged chain can cause serious injury.
WARNING: The saw chain is very sharp,
always wear protective gloves when performing
maintenance to the chain.
Improper filing angle of the side plate can
increase the risk of a severe kickback.
Raker (depth gauge) clearance. Too low
increases the potential for kickback. Not low
enough decreases cutting ability.
If cutter teeth have hit hard objects such
as nails and stones, or have been abraded
by mud or sand on the wood, have service
dealer sharpen chain.
NOTE: Inspect the drive sprocket for wear or dam-
age when replacing the chain. If signs of wear or
damage are present in the areas indicated, have
the drive sprocket replaced by a Craftsman Ser-
vice dealer.
TOP PLATE FILING ANGLE
See Figure 35.
CORRECT 30° - File holders are marked with
guide marks to align file properly to produce
correct top plate angle.
LESS THAN 30° - For Cross Cutting.
MORE THAN 30° - Feathered Edge Dulls
Quickly.
18 - English
MAINTENANcE
Wear inside the bar rails which permits the
chain to lay over sideways.
Bent guide bar.
Cracked or broken rails.
Spread rails.
In addition, guide bars with a sprocket at their tip
must be lubricated weekly with a grease syringe to
extend the guide bar life. Using a grease syringe,
lubricate weekly in the lubricating hole.
sIDE PLATE ANGLE
See Figure 36.
CORRECT - 80° Produced automatically if
correct diameter file is used in file holder.
HOOK - “Grabs” and dulls quickly. Increases
potential of KIcKBAcK.
Results from using a file with diameter too
small, or file held too low.
BACKWARD SLOPE - Needs too much feed
pressure, causes excessive wear to bar and
chain.
Turn the guide bar and check that the lubrication
holes and chain groove are free from impurities.
Results from using a file with diameter too
large, or file held too high.
REVERsING THE GUIDE BAR
Remove the chain from the bar and turn the
DEPTH GAUGE cLEARANcE
bar over.
See Figure 37 - 39.
NOTE: Bottom of bar should not be on top.
The Raker (depth gauge) should be main-
tained at a clearance of .025 in. Use a depth
gauge tool for checking the depth gauge
clearances.
Replace the chain on the bar. Refer to As-
sembling the Bar and chain earlier in this
manual for specific information.
Tighten the screw with your finger.
Every time the chain is filed, check the depth
From the finger-tight position, tighten the
screw an additional 3/4 of a turn using a
wrench.
gauge clearance.
Use a Flat File and a Depth Gauge Jointer to lower
all gauges uniformly. Depth gauge jointers are
available in .020 in. to .035 in. Use a .025 in. depth
gauge jointer. After lowering each depth gauge,
restore original shape by rounding the front. Be
careful not to damage adjoining drive links with
the edge of the file.
Depth gauges must be adjusted with the flat file in
the same direction the adjoining cutter was filed
with the round file. Use care not to contact cutter
face with flat file when adjusting depth gauges.
WARNING: Remove the battery pack and
make sure the chain has stopped before you
do any work or making any adjustments on the
saw. Failure to do so may result in accidental
starting and possible serious injury.
TRANsPORTING AND sTORING
See Figure 41.
Do not store or transport the chain saw when
it is running. The chain saw should always be
idle before storing or transporting.
Always place the chain cover on the bar and
chain before storing or transporting the chain
saw. Use caution to avoid the sharp teeth of
the chain.
Clean the chain saw thoroughly before stor-
ing. Store the chain saw indoors, in a dry
place that is locked and/or inaccessible to
children.
GUIDE BAR MAINTENANcE
See Figure 40.
When the guide bar shows signs of wear, reverse
it on the saw to distribute the wear for maximum
bar life. The bar should be cleaned every day of
use and checked for wear and damage.
Feathering or burring of the bar rails is a nor-
mal process of bar wear. Such faults should be
smoothed with a file as soon as they occur.
A bar with any of the following faults should be
replaced.
Keep away from corrosive agents such as
garden chemicals and de-icing salts.
19 - English
TROUBLEsHOOTING
PROBLEM
cAUsE
sOLUTION
1. Check chain tension for
Bar and chain running
hot and smoking.
1. Tension chain. Refer to chain
over tight condition
Tension earlier in this manual.
2. Chain oil tank empty.
2. Check oil tank.
Motor runs, but chain is
not rotating.
1. Chain tension too tight.
1. Retension chain, Refer to chain
Tension earlier in this manual.
2. Refer to Assembling the Bar and
2. Checkguidebarandchain
assembly.
chain earlier in this manual.
3. Inspect guide bar and chain for
damage.
3. Checkguidebarandchain
for damage.
CALL US FIRST
For any questions about operating or maintaining your product,
call the Craftsman® Help Line!
Your product has been fully tested prior to shipment to ensure
your complete satisfaction.
1-800-932-3188
20 - English
Fig. 1
Fig.4
A
B
J
L
A
K
A- Rotational kickback (contragolpe
rotatorio)
e
Fig. 2
A
I
F
C
A- Kickback danger zone (zona de peligro
de contragolpe)
D
Fig. 3
G
H
A
A- Chain cover (tapa de la cadena)
B- Chain oil tank cap (tapa del tanque del
aceite de la cadena)
G -Hex key (llave hexagonal)
H -Hex key storage area (compartimiento
de la llave hexagonal)
C -Bar (barra)
D -Chain (cadena)
I - Trigger (gatillo)
J - Trigger lock-out button (botón de
seguro del gatillo)
K -Front handle (mango delantero)
L -Rear handle (mango posterior)
E -Hand guard (protección de la mano)
F - Battery pack (not included) (paquete de
pilas [no viene incluido])
B
A- Pull (tirón)
B -Push (empujón)
i
Fig. 5
Fig. 8
Fig. 11
A
A
B
B
C
Fig. 9
A- Battery port (receptáculo de las pilas)
B- Latches (pestillos)
C- Battery pack (paquete de pilas)
A- Chain Line (plano de la cadena)
B- Straight arm position (posición con el
brazo recto)
Fig. 6
Fig. 12
A
Fig. 10
90°
B
PLAnneD PATH oF SAFe ReTReAT 135°
FRom PLAnneD LIne oF FALL
TRAyeCToRIA De ReTIRADA SeGURA A
135º De LA LíneA PLAneADA De CAíDA
DeL áRBoL
Fig. 7
A- Planned line of fall (línea planeada de
A
caída)
CHAIn LIne
PLAno De LA CADenA
B- Safe retreat zone (zona de retirada
segura)
B
A- Trigger lock-out button (botón de seguro
del gatillo)
B- Trigger (gatillo)
ii
Fig. 13
Fig. 16
Fig. 19
LoG SUPPoRTeD AT one enD
B
TRonCo APoyADo PoR Un exTRemo
135°
135°
45°
45°
A
B
90°
A
B
C
A
A- Planned line of fall (línea planeada de
caída)
B- Safe retreat zone (zona de retirada
segura)
A- Wedge (cuña)
LoG SUPPoRTeD AT BoTH enDS
TRonCo APoyADo PoR AmBoS
exTRemoS
Fig. 17
Fig. 14
A
B
C
A
C
A
A- Finishing cut (corte final)
B- LOAD (carga)
A- Kickback (contragolpe)
B
C -1st cut 1/3 dia (primer corte, 1/3 del
diám.)
Fig. 18
A- Hinge 2 in. or 1/10 dia (bisagra 51 mm
[2 pulg.] ó 1/10 del diám.)
B- Back cut 2 in. (corte trasero 51 mm [2
pulg.])
Fig. 20
C -Notch - approx. 1/3 diameter of trunk
(muesca - aprox. 1/3 del diámetro del
tronco)
A
Fig. 15
B
C
A
B
A -Underbucking (tronzado por abajo)
B- Overbucking (tronzado por arriba)
A- Back cut (corte trasero)
B- Hinge (bisagra)
C -Notch (muesca)
iii
Fig. 21
Fig. 24
Fig. 26
3
2
B
1
G
4
I
C
A
CUT LImBS one AT A TIme AnD LeAve
SUPPoRT LImBS UnDeR TRee UnTIL
LoG IS CUT
A
H
CoRTe UnA RAmA A LA veZ y DeJe
RAmAS De SoPoRTe BAJo eL áRBoL
HASTA qUe eSTé CoRTADo eL TRonCo
D
A- Chain tensioning screw (tornillo de
tensado de la cadena)
F
e
A- Adjusting pin (pasador de ajuste)
B- Sprocket (rueda dentada)
C -Chain tension pin hole (orificio del
pasador de tensado de la cadena)
D -Chain (cadena)
Fig. 27
Fig. 22
E -Chain cover (tapa de la cadena)
F - Chain cover screw (tornillo de tensado
de la cadena)
A
B
G -Washer (arandela)
H -Bar (barra)
I - Retaining pin (pasador de retención)
LIFT THe TIP oF THe GUIDe BAR UP To
CHeCK FoR SAG
Fig. 25
C
LevAnTe LA PUnTA De LA BARRA
GUíA PARA RevISAR LA HoLGURA
De LA CADenA
D
A- Second cut (segundo corte)
B- Load (carga)
B
C -First cut 1/3 diameter (primer corte
1/3 del diámetro)
Fig. 28
A
D -Finishing cut (corte final)
A- Chain drive links (eslabones de
impulsión de la cadena)
B- Bar groove (ranura de la barra)
Fig. 23
A
A
A - Hex key (llave hexagonal)
A- Springpole (pértiga)
iv
Fig. 29
Fig. 33
Fig. 34
Fig. 36
CoRReCT SIDe PLATe FILInG AnGLe
ánGULo CoRReCTo De LImADURA De
LA PLACA LATeRAL
APPRox. .050 in.
Aprox. 0.050 pulg. (1.25 mm)
80°
Fig. 30
A
InCoRReCT SIDe PLATe FILInG AnGLe
FLATS / PARTeS PLAnAS
ánGULo InCoRReCTo De LImADURA De
LA PLACA LATeRAL
B
Fig. 31
A
A
B
B
H
A- Left hand cutters (dientes de corte
izquierdos)
B -Right hand cutters (dientes de corte
derechos)
G
C
D
F
Fig. 35
A- Hook (gancho)
e
B -Backward slope (pendiente hacia atrás)
CoRReCT ToP PLATe FILInG AnGLe
A- Cutting corner (esquina de corte)
B -Top plate (placa superior)
C -Rivet hole (orificio del remache)
D -Heel (talón)
ánGULo CoRReCTo De LImADURA De
LA PLACA SUPeRIoR
Fig. 37
E -Gullet (garganta)
A
F - Toe (puntera)
G -Depth gauge (calibre de profundidad)
H -Side Plate (placa lateral)
30°
A- Raker clearance (.025 in.) (espacio libre
de los dientes limpiadores 0.025 pulg.
[0.6 mm])
InCoRReCT ToP PLATe FILInG AnGLe
Fig. 32
ánGULo InCoRReCTo De LImADURA De
LA PLACA SUPeRIoR
Fig. 38
A
B
A
A
A- Less than 30° (menos de 30°)
B -More than 30° (más de 30°)
A- Check for wear or damage (revise para
ver si hay desgaste o daños)
B
A- Depth gauge jointer (igualador de
calibres de profundidad)
B -Flat file (lima plana)
v
Fig. 39
Fig. 41
A
A- Restore original shape by rounding
the front (restablezca la forma original
redondeando la parte frontal)
Fig. 40
A
A- Lubricating
lubricación)
hole
(orificio
de
vi
cRAFTsMAN cHAINsAW – MODEL NUMBER 315.341300
The model number will be found on a plate attached to the motor housing. Always mention the model
number in all correspondence regarding your cHAINsAW or when ordering repair parts.
sEE BAcK PAGE FOR PARTs ORDERING INsTRUcTIONs
21
1
17
22
2
3
8
7
6
18
9
10
20
4
11
12
13
16
14
19
®
15
5
PARTs LIsT
Key Part
No. Number
Description
Qty.
1
31119329G
32901329G
34116329G
31115329G
Chain Oil Tank Cap Assembly ..........................................................................1
Hex Key (5 mm)................................................................................................1
Chain Cover......................................................................................................1
Bar Cover Assembly.........................................................................................1
Chain ................................................................................................................1
Retaining Ring ..................................................................................................1
Washer..............................................................................................................1
Sprocket...........................................................................................................1
Housing Bar Pad ..............................................................................................1
Rear Lock Plate................................................................................................1
Front Lock Plate ...............................................................................................1
Adjusting Pin ....................................................................................................1
Adjusting Screw................................................................................................1
Bar (10 in.) ........................................................................................................1
Charger (Item No. 9 11041)...............................................................................1
2
3
4
5
6
6958301 or 690583002
3290875G
7
8
9
33302102G
33902102G
34202329G
34103329G
33303155G
33303329G
33201155G
671834006
1425301
10
11
12
13
14
15
16
17
18
19
20
21
22
130279003 or 130279005 Battery Pack (Item No. 9 11375)........................................................................1
31121329G
3220107G
Hand Guard Assembly .....................................................................................1
Screw (M4.2 x 14 mm)......................................................................................2
Screw (M6 x 35 mm).........................................................................................1
Logo Label........................................................................................................1
Warning Label...................................................................................................1
Battery Warning Label
32215301G
099949001904
940654093
099949001902
987000680
Operator’s Manual............................................................................................1
21 - English
NOTEs
23 - English
NOTEs
22 - English
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
1-800-4-MY-HOME® (1-800-469-4663)
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
1-800-488-1222 (U.S.A.)
1-800-469-4663 (Canada)
To purchase a protection agreement on a product serviced by Sears:
1-800-827-6655 (U.S.A.)
1-800-361-6665 (Canada)
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
1-800-LE-FOYERMC
1-888-SU-HOGAR®
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
© Sears Brands, LLC
|