Operator’s Manual
7-1/4 in. SLIDING COMPOUND
MITER SAW WITH LASER TRAC®
Model No. 137.211940
CAUTION:
●
●
●
●
●
Safety Instructions
Installation
Operation
Maintenance
Parts List
Before using this Miter Saw,
read this manual and follow
all its Safety Rules and
Operating Instructions
Customer Help Line
For Technical Support
1-800-843-1682
Sears Parts &
Repair Center
1-800-488-1222
Sears, Roebuck and Co., Hoffman Estates, lL 60179 USA
Part No. 137211940001
Printed in China
PRODUCT SPECIFICATIONS
MOTOR
Power Source ..................................................................... 9Amp, 120V AC, 60Hz
Speed ................................................................................. 5000 RPM (No load)
Brake .................................................................................. Electric
Double Insulated ................................................................. Yes
BLADE SIZE
Diameter.............................................................................. 7-1/4 in.
Arbor size............................................................................ 5/8in.
ROTATING TABLE:
Diameter............................................................................ 9-1/32 in.
Miter Detent Stops ............................................................ 0, 15, 22.5, 31.6, 45º R & L
Bevel Positive Stops ......................................................... 0, 45º L
CUTTING CAPACITY:
Crosscut ............................................................................ 2 in. x 8 in.
Miter 45° R & L................................................................... 2 in. x 6 in.
Bevel 45º L......................................................................... 1-1/2 in. x 8 in.
45° Miter and 45° Bevel..................................................... 1-1/2 in. x 6 in.
WARNING
!
To avoid electrical hazards, fire hazards or damage to the tool, use proper
circuit protection.
This tool is wired at the factory for 110-120 Volt operation. It must be
connected to a 110-120 Volt / 15 Ampere time delay fuse or circuit breaker.
To avoid shock or fire, replace power cord immediately if it is worn, cut or
damaged in any way.
Before using your tool, it is critical that you read and understand these
safety rules. Failure to follow these rules could result in serious injury to
you or damage to the tool.
3
SYMBOLS
WARNING ICONS
Your power tool and its Operator’s Manual may contain “WARNING ICONS”
(a picture symbol intended to alert you to, and/or instruct you how to avoid,
a potentially hazardous condition). Understanding and heeding these
symbols will help you operate your tool better and safer. Shown below are
some of the symbols you may see.
SAFETY ALERT: Precautions that involve your safety.
PROHIBITION
WEAR EYE PROTECTION: Always wear safety goggles or safety
glasses with side shields.
READ AND UNDERSTAND OPERATOR’S MANUAL: To reduce
the risk of injury, user and all bystanders must read and understand
operator’s manual before using this product.
KEEP HANDS AWAY FROM BLADE: Failure to keep your hands
away from the blade will result in serious personal injury.
SUPPORT AND CLAMP WORK
DANGER: indicates an imminently hazardous situation
which, if not avoided, will result in death or serious injury.
DANGER
!
WARNING: indicates a potentially hazardous situation
which, if not avoided, could result in death or serious
injury.
WARNING
!
CAUTION: indicates a potentially hazardous situation
which, if not avoided, may result in minor or moderate
injury.
CAUTION
!
CAUTION: used without the safety alert symbol indicates
a potentially hazardous situation which, if not avoided,
may result in property damage.
CAUTION
4
POWER TOOL SAFETY
GENERAL SAFETY INSTRUCTIONS
8. DO NOT FORCE THE TOOL. It will
do the job better and safer at the
rate for which it was designed.
BEFORE USING THIS POWER TOOL
Safety is a combination of common
sense, staying alert and knowing how
to use your power tool.
9. USE THE RIGHT TOOL. Do not
force the tool or an attachment
to do a job for which it was not
designed.
CAUTION
To avoid mistakes that could cause
serious injury, do not plug the tool in
until you have read and understood
the following.
10. USE PROPER EXTENSION
CORDS. Make sure your extension
cord is in good condition. When
using an extension cord, be sure
to use one heavy enough to carry
the current your product will draw.
An undersized cord will result in
a drop in line voltage and in loss
of power which will cause the tool
to overheat. The table on page
10 shows the correct size to use
depending on cord length and
nameplate ampere rating. If in
doubt, use the next heavier gauge.
The smaller the gauge number, the
heavier the cord.
1. READ and become familiar with
the entire Operator’s
Manual. LEARN the tool’s
application, limitations and
possible hazards.
2. KEEP GUARDS IN PLACE and in
working order.
3. REMOVE ADJUSTING KEYS
AND WRENCHES. Form the habit
of checking to see that keys and
adjusting wrenches are removed
from the tool before turning ON.
11. WEAR PROPER APPAREL. Do
not wear loose clothing, gloves,
neckties, rings, bracelets or other
jewelry which may get caught in
moving parts. Nonslip footwear is
recommended. Wear protective
hair covering to contain long hair.
4. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite
accidents.
5. DO NOT USE IN DANGEROUS
ENVIRONMENTS. Do not use
power tools in damp locations, or
expose them to rain or snow. Keep
work area well lit.
12.
ALWAYS WEAR EYE
PROTECTION. Any power
tool can throw foreign
6. KEEP CHILDREN AWAY. All
visitors and bystanders should be
kept a safe distance from work
area.
objects into the eyes and
could cause permanent eye
damage. ALWAYS wear Safety
Goggles (not glasses) that comply
with ANSI Safety standard Z87.1.
Everyday eyeglasses have only
impact–resistant lenses. They
ARE NOT safety glasses. Safety
Goggles are available at sears.
7. MAKE WORKSHOP CHILD
PROOF with padlocks, master
switches or by removing starter
keys.
5
NOTE: Glasses or goggles not in
compliance with ANSI Z87.1 could
seriously injure you when they
break.
and any other conditions that may
affect its operation. A guard or
other part that is damaged should
be properly repaired or replaced.
13. WEAR A FACE MASK OR DUST
MASK. Sawing operation produces
dust.
20. NEVER LEAVE THE TOOL
RUNNING UNATTENDED. TURN
THE POWER “OFF”. Do not walk
away from a running tool until the
blade comes to a complete stop
and the tool is unplugged from the
power source.
14.
SECURE WORK. Use
clamps or a vise to hold work
when practical. It is safer
than using your hand and it
frees both hands to operate
the tool.
21. DO NOT OVERREACH. Keep
proper footing and balance at all
times.
15. DISCONNECT TOOLS FROM
POWER SOURCE before servicing, 22. MAINTAIN TOOLS WITH CARE.
and when changing accessories
such as blades, bits and cutters.
Keep tools sharp and clean for best
and safest performance. Follow
instructions for lubricating and
changing accessories.
16. REDUCE THE RISK OF
UNINTENTIONAL STARTING.
Make sure switch is in the OFF
position before plugging the tool in.
23. WARNING: Dust generated from
certain materials can be hazardous
to your health. Always operate saw
in well-ventilated area and provide
for proper dust removal.
17. USE RECOMMENDED
ACCESSORIES. Consult
this Operator’s Manual for
recommended accessories. The
use of improper accessories may
cause risk of injury to yourself or
others.
!
DANGER
24.
People with
electronic devices, such as
pacemakers, should consult their
physician(s) before using this
product. Operation of electrical
equipment in close proximity to
a heart pacemaker could cause
interference or failure of the
pacemaker.
18. NEVER STAND ON THE TOOL.
Serious injury could occur if the
tool is tipped or if the cutting tool is
unintentionally contacted.
19. CHECK FOR DAMAGED PARTS.
Before further use of the tool, a
guard or other part that is damaged
should be carefully checked to
determine that it will operate
properly and perform its intended
function – check for alignment of
moving parts, binding of moving
parts, breakage of parts, mounting
6
COMPOUND MITER SAW SAFETY
SPECIFIC SAFETY INSTRUCTIONS
FOR THIS COMPOUND MITER SAW
10. USE only blade collars specified for
your saw.
1. DO NOT operate the miter saw
until it is completely assembled
and installed according to these
instructions.
11. NEVER use blades larger in
diameter than 7-1/4 inches.
12. NEVER apply lubricants to the
blade when it is running.
2. IF YOU ARE NOT thoroughly
familiar with the operation of miter
saws, seek guidance from your
supervisor, instructor or other
qualified person.
13. ALWAYS check the blade for
cracks or damage before operation.
Replace a cracked or damaged
blade immediately.
3. ALWAYS hold the work firmly
against the fence and table.
DO NOT perform any operation
free hand (use clamp wherever
possible).
14. NEVER use blades recommended
for operation at less than 5000
RPM.
15. ALWAYS keep the blade guards in
place and use at all times.
4. KEEP HANDS out of the path of
the saw blade. If the workpiece
you are cutting would cause your
hands to be within 6-3/4 in. of the
saw blade, the workpiece should
be clamped in place before making
the cut.
16. NEVER reach around the saw
blade.
17. MAKE SURE the blade is not
contacting the workpiece before the
switch is turned ON.
5. BE SURE the blade is sharp, runs
18. IMPORTANT: After completing the
cut, release the trigger and wait for
the blade to stop before returning
the saw to the raised position.
freely and is free of vibration.
6. ALLOW the motor to come up to
full speed before starting a cut.
19. MAKE SURE the blade has come
to a complete stop before removing
or securing the workpiece,
7. KEEP THE MOTOR AIR SLOTS
CLEAN and free of chips or dust.
changing the workpiece angle or
changing the angle of the blade.
8. ALWAYS MAKE SURE all handles
are tight before cutting, even if the
table is positioned in one of the
positive stops.
20. NEVER cut metals or masonry
products with this tool. This miter
saw is designed for use on wood
and wood-like products.
9. BE SURE both the blade and the
collar are clean and the arbor bolt
is tightened securely.
7
21. NEVER cut small pieces. If the
workpiece being cut would cause
your hand or fingers to be within
6-3/4 in. of the saw blade the
workpiece is too small.
22. PROVIDE adequate support to the
sides of the saw table for long work
pieces.
23. NEVER use the miter saw in an
area with flammable liquids or
gases.
24. NEVER use solvents to clean
plastic parts. Solvents could
possibly dissolve or otherwise
damage the material.
25. SHUT OFF the power before
servicing or adjusting the tool.
26. DISCONNECT the saw from
the power source and clean the
machine when finished using.
27. MAKE SURE the work area is
clean before leaving the machine.
28. SHOULD any part of your miter saw
be missing, damaged, or fail in any
way, or any electrical component
fail to perform properly, lock the
switch and remove the plug from
the power supply outlet. Replace
missing, damaged, or failed parts
before resuming operation.
8
ELECTRICAL REQUIREMENTS AND SAFETY
POWER SUPPLY AND MOTOR
SPECIFICATIONS
The AC motor used in this saw is
a universal, nonreversible type.
See “MOTOR” in the “PRODUCT
SPECIFICATIONS” section on page 3.
way. If the plug does not fit fully in the
outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to
install the proper outlet. Do not change
the plug in any way.
WARNING
Double insulation does not take the
place of normal safety precautions
when operating this tool.
!
WARNING
!
To avoid electrical hazards, fire
hazards, or damage to the tool,
use proper circuit protection. Your
saw is wired at the factory for 120
V operation. Connect to a 120 V, 9A
circuit and use a 9 A time delay fuse
or circuit breaker. To avoid shock
or fire, if power cord is worn or
cut, or damaged in any way, have it
replaced immediately.
To avoid electrocution:
1. Use only identical replacement parts
when servicing a tool with double
insulation. Servicing should be
performed by a qualified technician.
2. Do not use power tools in wet or
damp locations or expose them to
rain or snow.
DOUBLE INSULATED
MOTOR SAFETY PROTECTION
IMPORTANT
The power tool is double insulated to
provide a double thickness of insulation
between you and tool’s electrical
system. All exposed metal parts are
isolated from the internal metal motor
components with protecting insulation.
To avoid motor damage, the motor
should be blown out or vacuumed
frequently to keep sawdust from
interfering with the motor ventilation.
1. Connect this saw to a 120 V circuit.
This circuit must not be less than a
#18 wire with a 9 A time lag fuse.
NOTE: When using an extension
cord on a circuit with a #18 wire, the
extension cord must not exceed 25
feet in length.
Replacement parts – When servicing,
use only identical replacement parts.
Polarized plugs – This saw has a plug
that looks like the one shown below:
2. If the motor will not start, release
the trigger switch immediately.
UNPLUG THE SAW. Check the saw
blade to make sure it turns freely. If
the blade is free, try to start the saw
again. If the motor still does not start,
refer to the TROUBLESHOOTING
GUIDE.
3. If the tool suddenly stalls while
cutting wood, release the trigger
switch, unplug the tool and free the
blade from the wood. The saw may
To reduce the risk of electrical shock,
this saw has a polarized plug (one
blade is wider than the other). This plug
will fit in a polarized outlet only one
9
now be started and the cut finished.
4. FUSES may “blow” or circuit
breakers may trip frequently if:
a. MOTOR is overloaded –
excessive heat and damp or wet areas.
Use a separate electrical circuit for
your tools. This circuit must not be
less than a #18 wire with a 9 A time lag
overloading can occur if you feed fuse. NOTE: When using an extension
too rapidly or make too many
start/stops in a short time.
b. LINE VOLTAGE is more
than 10% above or below the
nameplate voltage rating. For
cord on a circuit with a #18 wire, the
extension cord must not exceed 25 feet
in length. Before connecting the tool to
the power line, make sure the switch
is in the OFF position and the electric
heavy loads, the voltage at motor current is rated the same as the current
terminals must equal the voltage
specified on the nameplate.
c. IMPROPER or dull saw blades
are used.
stamped on the motor nameplate,
running at a lower voltage will damage
the motor.
5. Most motor troubles may be traced
to loose or incorrect connections,
overload, low voltage or inadequate
power supply wiring. Always check
the connections, the load and
supply circuit if the motor doesn’t
run well. Check minimum gauge for
the length of cord you are using on
the chart below.
MINIMUM GAUGE FOR EXTENSION CORDS (AWG)
(When using 120 volts only)
Ampere Rating
Total length of Cord
More Than
Not More Than 25ft. 50ft. 100ft. 150ft.
0
6
18
18
16
14
16
16
16
16
14
14
14
12
12
6
10
12
16
10
12
12 Not Recommended
CAUTION: In all cases make certain
the receptacle in question is
properly grounded. If you are not
sure, have a certified electrician
check the receptacle.
GUIDELINES FOR EXTENSION
CORDS
Use a proper extension cord. Make
sure your extension cord is in good
condition. When using an extension
cord, be sure to use one heavy enough
to carry the current your product will
draw. An undersized cord will cause
a drop in line voltage, resulting in
loss of power and overheating. The
table below shows the correct size
to use depending on cord length and
nameplate ampere rating. If in doubt,
use the next heavier gauge. The
smaller the gauge number, the heavier
the cord.
Be sure your extension cord is
properly wired and in good condition.
Always replace a damaged extension
cord or have it repaired by a qualified
person before using it. Protect your
extension cords from sharp objects,
10
ACCESSORIES AND ATTACHMENTS
should be taken while mounting,
using, and storing carbide tipped
blades to prevent accidental
damage. Slight shocks, such as
striking the tip while handling,
can seriously damage the blade.
Foreign objects in the workpiece,
such as wire or nails, can also
cause tips to crack or break off.
Before using, always visually
examine the blade and tips for
bent blade, cracks, breakage,
missing or loose tips, or other
damage. Do not use if damage is
suspected. Failure to heed safety
instructions and warnings can
result in serious bodily injury.
RECOMMENDED ACCESSORIES
WARNING
!
●
Use only accessories
recommended for this miter
saw. Follow instructions that
accompany accessories. Use of
improper accessories may cause
hazards.
●
The use of any cutting tool
except 7-1/4 in. saw blades which
meet the requirements under
recommended accessories
is prohibited. Do not use
accessories such as shaper
cutters or dado sets. Ferrous
metal cutting and the use of
abrasive wheels is prohibited.
Do not attempt to modify this
tool or create accessories not
recommended for use with this
tool. Any such alteration or
modification is misuse and could
result in a hazardous condition
leading to possible serious
injury.
●
ACCESSORIES
Visit your Sears Hardware Department
or see the Sears Power and Hand Tool
Catalog to purchase recommended
accessories for this power tool.
WARNING
!
●
●
To avoid the risk of personal
injury, do not modify this power
tool or use accessories not
recommended by Sears.
Read warnings and conditions
on your CARBIDE TIPPED SAW
BLADE. Do not operate the saw
without the proper saw blade
guard in place. Carbide is a very
hard but brittle material. Care
11
TOOLS NEEDED FOR ASSEMBLY
Not supplied
Supplied
Phillips Screwdriver
Slotted Screwdriver
Blade Wrench
Adjustable Wrench
6mm Hex Wrench
Combination Square
COMBINATION SQUARE MUST BE TRUE
Should not gap or overlap when square is flipped over (see dotted figure).
Straight edge or a 3/4 in. board, this
Draw light line on
edge must be perfectly straight.
board along this edge.
Should not gap or overlap when square
flipped over (see dotted figure).
12
CARTON CONTENTS
3. Separate all parts from the packing
UNPACKING YOUR MITER SAW
material. Check each one with
the illustration to make certain all
items are accounted for, before
discarding any packing material.
WARNING
!
To avoid injury from unexpected
starting or electrical shock, do not
plug the power cord into a source
of power during unpacking and
assembly. This cord must remain
unplugged whenever you are
working on the saw.
WARNING
If any part is missing or
!
●
●
damaged, do not attempt to
assemble the miter saw, or
plug in the power cord until
the missing or damaged part
is correctly replaced. Call
1-800-843-1682 for missing or
damaged parts.
To avoid electric shock, use
only identical replacement parts
when servicing double insulated
tools. Call 1-800-4-MY-HOME® for
replacement parts.
1. Remove the miter saw from the
carton.
IMPORTANT: Do not lift miter saw
by the trigger switch handle. It
may cause misalignment. Only lift
machine by the base hand holds.
2. Place the saw on a secure
stationary work surface.
Support bracket assembly
Miter saw
Miter handle
Dust bag
Blade wrench
Hold-down clamp
13
KNOW YOUR SLIDING COMPOUND MITER SAW
Switch handle
Upper blade guard
ON/OFF trigger
switch
Bevel lock handle
Motor
Hold-down clamp
Laser guide
Table insert
Miter handle
Support bracket
Turntable
Mounting hole
Laser ON/OFF switch
Hold-down latch
Lower blade guard
Slide carriage
Slide carriage
lock knob
Bevel scale
Saw blade
Hand hold for
transportation
Positive miter detent
Positive stop locking lever
Base
14
GLOSSARY OF TERMS
AMPERAGE (AMPS) – A measure
eyes. Eye protection should meet the
requirements of ANSI Z.87.1 (USA) or
CSA Z94.3-M88 (Canada).
of the flow of electric current. Higher
ratings generally means the tool is
suited for heavier use.
FACE SHIELD – An impact resistant
shield that helps to protect your face
from chips, sparks, small debris.
Should only be used in conjunction with
additional eye protection.
ARBOR LOCK – Allows the user to
keep the blade from rotating while
tightening or loosening the arbor bolt
during blade replacement or removal.
BASE – Supports the table, holds
accessories and allows for workbench
or leg set mounting.
FENCE – Helps to keep the workpiece
from moving when sawing. Scaled to
assist with accurate cutting.
BEVEL LOCKING HANDLE – Locks
GUARD – Protective devise that forms
a barrier between a hazardous object
such as a blade, wheel or cutter and
the operator.
the miter saw at a desired bevel angle.
BEVEL SCALE – To measure the
bevel angle of the saw blade 0° to 45°
left.
HOLD DOWN LATCH – Locks the
miter saw in the lowered position for
compact storage and transportation.
CARBIDE TIPPED – Extremely hard
steel pieces with sharp cutting edges
fastened to cutting tools such as saw
blades.
INSTRUCTION OR OPERATOR’S
MANUAL – Booklet accompanying
your power tool that describes the
hazards and safe operation procedures,
outlines basic tool operation, care and
maintenance.
COVER PLATE SCREW – Loosen this
screw and rotate the plate for access to
the blade arbor bolt.
DOUBLE-INSULATED – A form of
electrical protection featuring two
separate insulation systems to help
protect against electrical shock.
MITER HANDLE – Used to rotate the
table, and to rotate the saw to a right or
left cutting position.
MITER SCALE – Measures the miter
EXTENSION CORD – An electric cord
used between power tools and outlets
to extend the range of the tools. The
more amerage your tool uses, the
longer the distance, the larger the size
of the wire needed in your extension
cord.
angle 0° to 45° left and right.
MOUNTING HOLES – To mount the
miter saw to a stable surface.
ON/OFF TRIGGER SWITCH – To start
the tool, squeeze the trigger. Release
the trigger to turn off the miter saw.
EYE PROTECTION – Goggles or
spectacles intended to protect your
15
POSITIVE STOP LOCKING LEVER –
KICKBACK – Sudden and unintended
Locks the miter saw at a preset positive movement of the tool or workpiece. It is
stop for the desired miter angle.
typically caused by binding or pinching
of the workpiece
SWITCH HANDLE – The switch
handle contains the trigger switch and
the laser on/off switch. The blade is
lowered into the workpiece by pushing
down on the handle. The saw will
return to its upright position when the
handle is released.
MITER CUT – A miter is a type of joint
where the two parts to be joined are cut
at an angle, and typically the finished
joint forms a 90-degree angle. Also
commonly spelled “mitre”.
REVOLUTIONS PER MINUTE (RPM)
– The number of turns completed by a
spinning object in one minute.
WARNING LABELS – Read and
understand for your own safety. Make
sure all labels are present on machine
and legible.
SAW BLADE PATH – The area of the
workpiece or table top directly in line
with the travel of the blade or the part
WRENCH STORAGE – Convenient
storage to prevent misplacing the blade of the workpiece which will be cut.
wrench.
SET – The distance between two saw
WOODWORKING TERMS
blade tips, bent outward in opposite
directions to each other. The further
apart the tips are, the greater the set.
ARBOR – The shaft on which a blade
is mounted.
THIN-KERF BLADE – Thinner than
normal blades, remove less material,
smaller kerfs (between .065 and .070).
Blade thinness also may increase the
heat generated while cutting.
BEVEL CUT – An angle cut made
through the face of the workpiece.
COMPOUND CUT – An angled cut
to both the edge and face of a board,
most common use is with crown
molding.
WORKPIECE – The wood being
cut. The surfaces of a workpiece are
commonly referred to as faces, ends
CROSS CUT – A cut which runs across and edges.
the board perpendicular to the grain.
FREEHAND – Performing a cut without
using a fence (guide), hold down or
other proper device to prevent the
workpiece from twisting during the
cutting operation.
HEEL – Misalignment of the blade.
KERF – The width of a saw cut,
determined by the thickness and set of
the blade.
16
ASSEMBLY AND ADJUSTMENTS
INSTALLING THE DUST BAG (FIG. C)
1. Squeeze the metal collar wings of
!
WARNING
To avoid injury, do not connect
this miter saw to the power source
until it is completely assembled and
adjusted, and you have read and
understood this Operator’s Manual.
the dust bag (1).
2. Place the dust bag neck opening
around the exhaust port (2), and
release the metal collar wings.
Fig. C
1
INSTALLING THE SUPPORT
BRACKET (FIG. A)
2
1. Place the support bracket (1) in
front of the miter saw as shown.
2. Tighten the two screws (2) using
a Phillips screwdriver into the pre-
drilled holes located in the front of
the table.
Fig. A
To empty the dust bag, squeeze the
metal collar and remove from exhaust
port. Open zipper on underside of bag
and empty into waste container.
NOTE: Check frequently and empty
bag before it gets full.
1
INSTALLING THE SAFETY HOLD-
DOWN CLAMP (FIG. D)
2
1. Loosen the hex screw (3) using a
Phillips screwdriver from the rear
side of the saw base.
2. Place the hold-down clamp
assembly (1) in one of the mounting
holes (2).
INSTALLING THE MITER HANDLE
(FIG. B)
1. Thread the miter handle (1) into the
hole located at the front of the miter
table.
3. Tighten the hex screw (3).
Fig. B
1
17
Fig. D
RELEASING CUTTING HEAD (FIG. G)
!
WARNING
2
To avoid injury and damage to the
saw, transport or store the miter
saw with the cutting head locked in
the down position. Never use the
hold down latch to hold the cutting
head in a down position for cutting
operations.
3
1
Unlocking
1. Push down slightly on the switch
handle (1).
SAW BLADE WRENCH (FIG. E)
2. Pull out the hold-down latch (2).
3. Allow the cutting head to rise to the
up position.
For convenient storage and prevention
of loss, there is a slot (1) in the right
side of the switch handle (2) for storing
the blade wrench (3) when not in use.
2
Fig. G
Fig. E
1
1
2
Locking
3
When transporting or storing the miter
saw, the cutting head should always be
locked in the down position.
1. Push the cutting head down to its
lowest position.
UNLOCKING THE SLIDE CARRIAGE
(FIG. F)
After removing the saw from the carton,
loosen the slide carriage lock knob
(1). When transporting or storing the
miter saw, the slide carriage should
always be locked in position. The slide
carriage lock knob (1) is located on the
right side of the slide carriage.
2. Push the hold-down latch (2) into
the locking hole.
IMPORTANT: To avoid damage, never
carry the miter saw by the switch
handle, the cutting arm or the miter
handle. Only lift machine by the base
hand holds.
Fig. F
WARNING
!
To avoid injury, disconnect the
plug from the power source before
performing any adjustments or
repair.
1
18
NOTE: Your miter saw was adjusted at
the factory. However, during shipment
slight misalignment may have occurred.
Check the following settings and adjust
if necessary prior to using this miter
saw.
Fig. H
1
REMOVING AND INSTALLING THE
TABLE INSERT (FIG. H)
2
WARNING
To avoid injury:
!
MOUNTING THE MITER SAW
(FIG. I, J)
● Always unplug the saw to avoid
accidental starting. Remove all
small pieces of material from the
table cavity before performing
any cuts. The table insert may
be removed for this purpose, but
always reattach the table insert
prior to performing a cutting
operation.
● Do not start the sliding compound
miter saw without checking for
interference between the blade
and table insert. Damage could
result to the blade, table insert or
turntable if blade strike occurs
during the cutting operation.
1. To remove, loosen and remove the
six screws (1) on the table inserts
(2) with a Phillips screwdriver and
remove the insert.
WARNING
To avoid injury form unexpected
saw movement:
● Disconnect the power cord from
the outlet, and lock the cutting
head in the lower position using
the stop latch.
● Lock the slide carriage in place
by tightening the slide carriage
lock knob.
● To avoid back injury, lift the saw
by using the designated carrying
handles located on the top of the
machine. When lifting, bend at
your knees, not from your back.
● Never carry the miter saw by
the power cord or by the switch
handle. Carrying the tool by the
power cord could cause damage
to the insulation or the wire
connections resulting in electric
shock or fire.
!
2. To install, reposition the table
inserts, install the six screws and
tighten.
3. Check for blade clearance by
moving the slide carriage through
the full motion of the blade in the
table slot.
● To avoid injury from flying debris,
do not allow visitors to stand
near the saw during any cutting
operation.
● Support the saw on a level work
surface.
● Always bolt or clamp the saw to
its support.
19
Mounting instructions
REMOVING OR INSTALLING THE
BLADE
1. For stationary use, place the saw
in the desired location, directly on
a workbench where there is room
for handling and proper support
of the workpiece. The base of the
saw has four mounting holes. Bolt
the base of the miter saw (1) to
the work surface (5), using the
fastening method as shown in Fig I.
Removing Blade (Fig. K, L, M)
WARNING
!
●
To avoid injury from an
accidental start, make sure the
switch is in the OFF position
and plug is not connected to the
power source outlet.
Fig. I
●
●
Only use a 7-1/4 inch diameter
blade.
2
1. Miter saw base
3
NEVER cut metals or masonry
products with this tool. This
miter saw is designed for use on
wood and wood-like products
only.
2. Hex head bolt
4
1
3. Rubber washer
4. Flat washer
5. Workbench
6. Flat washer
7. Lockwasher
8. Hex nut
9. Jam nut
5
8
6
1. Unplug the saw from the outlet.
2. Raise the miter saw to the upright
position.
7
9
NOTE: Mounting hardware is not
included with this tool. Bolts, nuts,
washers, & screws must be purchased
separately.
3. Raise the lower blade guard (1) to
the uppermost position. (Fig. K)
4. While holding the lower blade
guard, loosen the cover plate screw
(2) with a Phillips screwdriver.
5. Rotate the cover plate (3) to
expose the arbor bolt.
2.
For portable use, place the
saw on a 3/4 in. thick piece of
plywood. Bolt the base of the
miter saw securely to the
6. Place the blade end wrench over
the arbor bolt.
plywood using the mounting holes on
the base. Use C-clamps to clamp this
mounting board to a stable work
surface at the worksite. (Fig. J)
1
Fig. K
3
Fig. J
3/4 Inch
plywood
2
4
20
7. Locate the arbor lock (5) below
motor lower cover. (Fig. L)
INSTALLING BLADE (FIG. K, L, M)
WARNING
8. Press the arbor lock, holding it
in firmly while turning the blade
clockwise. The arbor lock will
then engage and lock the arbor.
Continue to hold the arbor lock,
while turning the wrench clockwise
to loosen the arbor bolt.
!
Un-plug the miter saw before
changing/installing the blade.
1. Install a 7-1/4 in. blade with a 5/8
in. arbor making sure the rotation
arrow on the blade matches the
clockwise rotation arrow on the
upper guard, and the blade teeth
are pointing downward.
Fig. L
2. Place the arbor collar (6) against
the blade and on the arbor. Thread
the arbor bolt (4) on the arbor. in a
counterclockwise direction. (Fig. M)
IMPORTANT: Make sure the flats
of the blade collars are engaged
with the flats on the arbor shaft.
Also, the flat-side of the arbor collar
must be placed against the blade.
3. Place the blade wrench on the
arbor bolt.
5
4. Press the arbor lock (5), holding
it in firmly while turning the blade
counterclockwise. When it engages,
continue to press the arbor lock
in, while tightening the arbor bolt
securely. (Fig. L)
9. Remove the arbor bolt (4), the
arbor collar (6), and the blade (7).
Do not remove the inner blade
collar. (Fig. M)
5. Rotate the cover plate (3) back to
its original position until the slot in
the cover plate engages with the
cover plate screw (2). While holding
the lower blade guard, tighten the
screw with a Phillips screwdriver.
(Fig. K) NOTE: The lower blade
guard must be raised to the upright
position to access the cover plate
screw.
10. Raise the lower clear plastic blade
guard (1) to the upright position
(Fig. K) to remove the blade.
NOTE: Pay attention to the pieces
removed, noting their position and
direction they face. Wipe the blade
collars clean of any sawdust before
installing a new blade.
7
Fig. M
6. Lower the blade guard (1) and
verify the operation of the guard
does not bind or stick (Fig. K).
7. Be sure the arbor lock (5) is
released so the blade turns freely
by spinning the blade until the arbor
lock disengages.
6
4
21
saw must be connected to the power
source and the laser on/off switch must
be turned on for the laser line to show.
WARNING
!
●
●
To avoid injury, never use the saw
without the cover plate secure
in place. It keeps the arbor bolt
from falling out if it accidentally
loosens, and helps prevent the
spinning blade from coming off
the saw.
Make sure the collars are clean
and properly arranged. Lower
the blade into the table and
check for any contact with the
metal base or the turn table.
WARNING
!
AVOID DIRECT EYE CONTACT
●
Laser is radiated when laser
guide is turned on. Avoid direct
eye contact. Always un-plug the
miter saw from power source
before making any adjustments.
Laser Warning Label: max
output <1mW DIODE LASER:
630-670nm, Complies with
21CFR 1040.10 and 1040. 11.
Class II laser product.
●
THE LASER GUIDE (FIG. N)
1. To turn laser on, press on/off rocker
switch (1) to “ON” position.
2. To turn off laser, press on/off rocker
switch to “OFF” position.
1
Fig. N
●
●
NOTE: All the adjustments for the
operation of this machine have
been completed at the factory. Due
to normal wear and use, some
occasional readjustments may be
necessary.
CAUTION-Use of controls or
adjustments or performance of
procedures other than those
specified herein may result in
hazardous radiation exposure.
CAUTION-The use of optical
instruments with this product
will increase eye hazard.
THE LASER BEAM
WARNING
!
For your own safety, never connect
the plug to power source outlet
until all the adjustment steps
are complete and you have read
and understood the safety and
operational instructions.
●
●
Do not attempt to repair or
disassemble the laser. If
Your tool is equipped with the Laser
Trac® cutting guide using Class II laser
beam. The laser beam will enable you
to preview the saw blade path on the
stock to be cut before starting the miter
saw. This laser guide is powered by the
transformed alternating current supply
directly through the power lead. The
unqualified persons attempt
to repair this laser product,
serious injury may result. Any
repair required on this laser
product should be performed
by authorized service center
personnel.
22
BEVEL STOP ADJUSTMENTS
(FIG. O, P, Q)
Fig. O
1
3
WARNING
!
To avoid injury from unexpected
starting or electrical shock, make
sure the trigger is released and
remove the power cord from the
power source.
4
90°(0°) Bevel adjustment (Fig. O)
1. Loosen bevel lock handle (1) and
tilt the cutting arm completely to the
right. Tighten the bevel lock handle.
2. Place a combination square (2) on
the miter table with the ruler against
the table and the heel of the square
against the saw blade.
2
5
3. If the blade is not 90o (0o) square
with the miter table (5), loosen the
bevel lock handle (1), tilt the cutting
head to the left, loosen the locknut
(4) on the bevel angle adjustment
bolt (3) and use a 10 mm wrench
to adjust the stop bolt (3) depth in
or out to increase or decrease the
bevel angle.
90° Bevel Pointer Adjustment (Fig. P)
1. When the blade is exactly 90o
(0o) to the table, loosen the bevel
indicator screw (6) using a # 2
Phillips screwdriver.
2. Adjust bevel indicator (7) to the
“0” mark on the bevel scale and
retighten the screw.
4. Tilt the cutting arm to back to the
right at 90o (0o) bevel and recheck
for alignment.
Fig. P
5. Repeat steps 1 through 4 if further
adjustment is needed.
6. Tighten bevel lock handle (1) and
locknut (4) when alignment is
achieved.
6
7
45o Bevel Adjustment (Fig. Q)
1. Loosen the bevel lock handle (8)
and tilt the cutting head completely
to the left.
2. Using a combination square, check
to see if the blade angle is 45° to
the table.
3. If the blade is not at 45° to the miter
table, tilt the cutting arm to the
right, loosen the locknut (9) on the
23
bevel angle adjustment bolt (10)
and use a 10 mm wrench to adjust
the stop bolt (10) depth in or out
to increase or decrease the bevel
angle.
2. Move the turntable while lifting up
on the positive stop locking lever
(2) to align the indicator (3) to the
desired degree measurement.
3. If the desired angle is one of the
nine positive stops, release the
positive stop locking lever, making
sure the lever snaps into position,
and then secure by tightening the
miter handle.
4. If the miter angle desired is not one
of the nine positive stops, simply
lock the miter table into desired
angle position by turning the miter
handle in the clockwise direction.
4. Tilt the cutting arm to the left to 45°
bevel and recheck for alignment.
5. Repeat steps 1 through 4 until the
blade is at 45° to the miter table.
6. Tighten bevel lock handle (8) and
locknut (9) when alignment is
achieved.
Fig. Q
10
Fig. R
4
1
9
8
3
2
MITER ANGLE ADJUSTMENT (FIG.
R)
MITER SCALE INDICATOR
ADJUSTMENT (FIG. R)
The sliding compound miter saw scale
can be easily read, showing miter
angles from 0° to 45° to the left, and 0°
to 45° to the right. The miter saw table
has nine of the most common angle
setttings with positive stops at 0°, 15°,
22.5°, 31.6°, and 45°. These positive
stops position the blade at the desired
angle quickly and accurately. Follow
the process below for quickest and
most accurate adjustments.
1. Move the table to the 0° positive
stop.
2. Loosen the screw (4) that holds the
indicator with a Phillips screwdriver.
3. Adjust the indicator (3) to the 0°
mark and retighten screw.
ADJUSTING FENCE SQUARENESS
(FIG. S)
1. Lower the cutting arm and lock in
position.
1. Unlock the miter table by turning the 2. Using a square (3), lay the heel of
miter handle (1) counterclockwise. the square against the blade and
24
the ruler against the fence (2) as
shown.
Fig. S
3. Loosen the two fence locking bolts
(1) with a 6mm hex wrench.
4. Adjust the fence 90° to the blade
and tighten the four fence locking
bolts.
1
CAUTION: If the saw has not
been used recently, recheck
blade squareness to the fence
and readjust if needed.
2
5. After fence has been aligned, using
a scrap piece of wood, make a cut
at 90o, then check squareness on
the piece. Readjust if necessary.
ADJUSTING CUTTING DEPTH
(FIG. T)
The maximum depth travel of the
cutting head was set at the factory.
Check to see that the blade does not
extend more than 1/4 in. below the
table insert, and does not touch the
control arm throat or any part of the
base or table. If the maximum depth
needs readjusting:
1. Loosen the stop knob (1) while
moving the cutting head down until
the blade extends just 1/4 in. below
the table insert.
Fig. S
1
1
2
3
2. Adjust the stop knob (1) to touch
the stop plate (2).
3. Recheck the blade depth by
moving the cutting head front to
back through the full motion of a cut
along the control arm. If the blade
touches the inside of the control
arm, readjust the setting.
SETTING CUTTING DEPTH (FIG. T)
The depth of cut can be preset for even
and repetitive shallow cuts.
1. Adjust the cutting head down (See
CUTTING HEAD section) until the
teeth of the blade are at the desired
depth.
2. While holding the upper arm in that
position, turn the stop knob (1) until
it touches the stop plate (2).
3. Recheck the blade depth by moving
the cutting head front to back
through the full motion of a typical
cut along the control arm.
25
OPERATION
SAFETY INSTRUCTIONS FOR BASIC
SAW OPERATION
● Check for damaged parts. Check
for:
● Alignment of moving parts
● Damaged electric cords
BEFORE USING THE MITER SAW
● Binding of moving parts
!
WARNING
● Mounting holes
To avoid mistakes that could cause
serious, permanent injury, do not
plug the tool in until the following
steps are completed:
● Completely assemble and adjust
the saw, following the instructions.
(ASSEMBLY AND ADJUSTMENTS)
● Learn the use and function of the
ON/OFF switch, upper and lower
blade guards, hold down latch, bevel
lock handle and cover plate screws.
● Review and understand all
safety instructions and operating
procedures in this Operator’s
● Function of arm return spring
and lower guard: Push the
cutting arm all the way down,
then let it rise until it stops.
The lower guard should fully
close. Follow instructions in
TROUBLESHOOTING GUIDE
for adjustment if necessary.
● Other conditions that may affect
the way the miter saw works.
● Keep all guards in place, in working
order and proper adjustment. If any
part of this miter saw is missing,
bent, damaged or broken in any way,
or any electrical parts do not work,
turn the saw off and unplug it.
● Replace bent, damaged, missing or
defective parts before using the saw
again.
● Maintain tools with care. Keep the
miter saw clean for best and safest
performance. Follow instructions for
lubricating. Do not put lubricants on
the blade while it is spinning.
● Remove adjusting wrench from the
tool before turning it on.
Manual. (SAFETY & OPERATIONS)
● Review the MAINTENANCE and
TROUBLESHOOTING GUIDE for
your miter saw.
● To avoid injury or possible death
from electrical shock:
Make sure your fingers do not
touch the plug’s metal prongs
when plugging or unplugging
your miter saw. (ELECTRICAL
REQUIREMENTS AND SAFETY)
BEFORE EACH USE INSPECT YOUR
SAW.
● Disconnect the miter saw.
To avoid injury from accidental
starting, unplug the saw before any
adjustments, including set-up and
blade changes.
● Compare the direction of rotation
arrow on the guard to the direction
arrow on the blade. The blade teeth
should always point downward at the
front of the saw.
● To avoid injury from jams, slips,
or thrown pieces, use only
recommended accessories.
RECOMMENDED ACCESSORIES
● Consult the ACCESSORIES and
ATTACHMENTS section of this
Operators Manual for recommended
accessories. Follow the instructions
that come with the accessory. The
use of improper accessories may
cause risk of injury to persons.
● Tighten the arbor bolt.
● Choose the correct 7-1/4 in.
● Tighten the cover plate screw.
diameter blade for the material and
26
the type of cutting you plan to do. Do CAUTION: This machine is not
not use thin kerf blades.
designed for cutting masonry,
masonry products, ferrous metals
(steel, iron, and iron-based metals.)
Use this miter saw to cut only
wood, wood-like products, or non-
ferrous metals. Other material may
shatter, bind the blade, or create
other dangers. Remove all nails that
may be in the workpiece to prevent
sparking that could cause a fire.
Remove dust bag when cutting non-
ferrous metals.
● Make sure the blade is sharp,
undamaged and properly aligned.
With the saw unplugged, push
the cutting arm all the way down.
Manually spin the blade and check
for clearance. Tilt the power-head to
a 45° bevel and repeat the test.
● Make sure the blade and arbor
collars are clean.
● Make sure all clamps and locks are
tight and there is no excessive play
in any parts.
DRESS FOR SAFETY
KEEP YOUR WORK AREA CLEAN
Cluttered areas and benches invite
accidents.
Any power tool can throw
foreign objects into the eyes.
This can result in permanent
eye damage. Everyday eyeglasses
have only impact resistant lenses and
are not safety glasses. Glasses or
!
WARNING
To avoid burns or other fire damage, goggles not in compliance with ANSI
never use the miter saw near
flammable liquids, vapors, or gases.
● Plan ahead to protect your eyes,
hands, face and ears.
● Know your miter saw. Read and
understand the Operator’s Manual
and labels affixed to the tool. Learn
its application and limitations as well
as the specific potential hazards
peculiar to this tool. To avoid injury
from accidental contact with moving
parts, do not do layout, assembly, or
setup work on the miter saw while
any parts are moving.
Z87.1 could seriously injure you when
they break.
● Do not wear loose clothing, gloves,
neckties or jewelry (rings, watches).
They can get caught and draw you
into moving parts.
● Wear non-slip footwear.
● Tie back long hair.
● Roll long sleeves above the elbow.
● Noise levels vary widely. To avoid
possible hearing damage, wear ear
plugs when using any miter saw.
● For dusty operations, wear a dust
mask along with safety goggles.
● Avoid accidental starting, make sure
the trigger switch is disengaged
before plugging the miter saw into a
power outlet.
INSPECT YOUR WORKPIECE
Make sure there are no nails or foreign
objects in the part of the workpiece
being cut.
PLAN YOUR WORK
Plan your work to avoid small pieces
● Use the right tool. Do not force a tool that may bind, or that are too small to
or attachment to do a job it was not
designed to do. Use a different tool
for any workpiece that can’t be held
in a solidly braced, fixed position.
clamp and get a solid grasp on. Plan
the way you will grasp the workpiece
from start to finish. Avoid awkward
operations and hand positions.
27
A sudden slip could cause your fingers
or hand to move into the blade.
“no hands zone” area marked on the
saws table.
● When cutting odd shaped
DO NOT OVER-REACH
workpieces, plan your work so it
will not bind in the blade and cause
possible injury. Molding, for example,
must lie flat or be held by a fixture or
jig that will not let it move when cut.
● Properly support round material such
as dowel rods, or tubing, which have
a tendency to roll when cut, causing
the blade to “bite”.
Keep good footing and balance. Keep
your face and body to one side, out of
the line of a possible kickback. NEVER
stand in the line of the blade.
Never cut freehand:
● Brace your workpiece firmly against
the fence and table stop so it will not
rock or twist during the cut.
● Make sure there is no debris
between the workpiece and the table
or fence.
!
WARNING
● Make sure there are no gaps
between the workpiece, fence and
table that will let the workpiece shift
after it is cut.
● Keep the cut off piece free to move
sideways after it is cut off. Otherwise,
it could get wedged against the
blade and thrown violently.
To avoid injury, follow all applicable
safety instructions, when cutting
non-ferrous metals:
● Use only saw blades specifically
recommended for non-ferrous metal
cutting.
● Do not cut metal workpieces
that must be hand held. Clamp
workpieces securely.
● Cut non-ferrous metals only if you
are under the supervision of an
experienced person and the dust
bag has been removed from the
saw.
● Only the workpiece should be on the
saws table.
● Secure work. Use clamps or a vise
to help hold the work when it is
practical.
USE EXTRA CAUTION WITH LARGE
OR ODD SHAPED WORKPIECES.
● Use extra supports (tables,
WHEN SAW IS RUNNING
!
WARNING
sawhorses, blocks, etc.) for
workpieces large enough to tip.
● Never use another person as a
Do not allow familiarity from
frequent use of your miter saw
substitute for a table extension, or as to result in a careless mistake. A
an additional support for a workpiece careless fraction of a second is
that is longer or wider than the basic
miter saw table, or to help feed,
support, or pull the workpiece.
enough to cause a severe injury.
Before cutting, if the saw makes an
unfamiliar noise or vibrates, stop
immediately. Turn the saw OFF.
Unplug the saw. Do not restart until
finding and correcting the problem.
● Do not use this saw to cut small
pieces. If the workpiece being cut
would cause your hand or fingers
to be within 6-3/4 inches of the saw
blade the workpiece is too small.
Keep hands and fingers out of the
28
BODY AND HAND POSITION (FIG. U)
Fig. U
WARNING
!
Never place hands near
the cutting area. Proper
positioning of your body
and hands when operating the miter
saw will make cutting easier and
safer. Keep children away. Keep all
visitors at a safe distance from the
miter saw. Make sure bystanders are
clear of the saw and workpiece. Do
not force the saw. It will do the job
better and safer at its designed rate.
No Hand Zone
13-1/2 in.
BASIC SAW OPERATIONS
Starting a cut:
●
●
●
Place hands at least 6-3/4 in. away
on both sides of the blade path -
“no-hands zone”. (Fig. U)
Hold workpiece firmly against the
fence to prevent movement toward
the blade.
With the power switch OFF,
bring the saw blade down to the
workpiece to see the cutting path of
the blade.
Squeeze trigger switch to start saw.
Lower blade into workpiece with a
firm downward motion.
WARNING
!
For your convenience, your saw
has a blade brake. The brake is
not a safety device. Never rely on
it to replace the proper use of the
guard on your saw. If the blade
does not stop within approximately
10 seconds, wait for the blade to
stop, unplug the saw and check
the Troubleshooting Guide on
page 39. Contact customer service
at 1-800-843-1682 for additional
technical information is needed.
●
●
Finishing a cut:
●
Hold the cutting arm in the down
position.
TO TURN THE SAW ON (FIG. V)
Depress the trigger switch (1) to turn
on the miter saw started.
●
Release trigger switch and wait
for all moving parts to stop before
moving your hands and raising the
cutting arm.
If the blade does not stop within
10 seconds, unplug the saw
and follow the instructions in
TROUBLESHOOTING GUIDE
section.
The miter saw is equipped with an
automatic blade brake. When the
trigger switch is released, the electric
blade brake will stop the blade within
approximately 10 seconds.
●
NOTE: Make the ON/OFF switch
childproof. Insert a padlock, or chain
with padlock, through the hole (2) in
the trigger switch, locking the tool’s
switch, preventing children and other
unauthorized users from turning the
machine on.
Before freeing jammed material:
●
●
●
Release trigger switch.
Wait for all moving parts to stop.
Unplug the miter saw.
29
Fig. V
WARNING
!
1
To avoid injury from materials being
thrown, always unplug the saw
to avoid accidental starting, and
remove small pieces of material
from the table cavity.
2
MITER CUT (FIG. X)
SLIDING CARRIAGE SYSTEM (FIG.
W)
1. When a miter cut is required,
unlock the miter table by turning the
miter handle (1) counterclockwise.
2. While holding the miter handle,
lift up on the positive stop locking
lever (2).
WARNING
!
To reduce the risk of injury, return
carriage to the full rear position after
each crosscut operation.
1. For a chop cutting operations on
small workpieces, slide the cutting
head assembly completely toward
the rear of the unit and tighten the
carriage lock knob (1).
2. To cut wide boards up to 8 in.,
the carriage lock knob should be
loosened to allow the cutting head
to slide freely.
3. Rotate the miter table to the right or
left with the miter handle.
4. When the table is in the desired
position, as shown on the miter
scale (3), release the positive stop
locking lever and tighten the miter
handle. The table is now locked at
the desired angle. Positive stops
are provided at 0°, 15°, 22.5°, 31.6°
and 45°.
IMPORTANT: Always tighten the
miter table lock handle before
performing every cutting operation.
Fig. W
Fig. X
1
BEFORE LEAVING THE SAW
●
Never leave tool running
unattended. Turn power OFF. Wait
for all moving parts to stop.
●
Make workshop childproof. Lock the
shop. Disconnect master switches.
Store tool away from children and
other unqualified users.
2
3
1
30
BEVEL CUT (FIG. Y)
Fig. Z
1. When a bevel cut is required,
loosen the bevel lock handle (1) by
turning it clockwise.
2. Tilt the cutting head to the desired
angle, as shown on the bevel scale
(2).
3. The blade can be positioned at
any angle, from a 90° straight cut (
0° on the scale) to a 45° left bevel.
Tighten the bevel lock handle (1)
to lock the cutting head in position.
Positive stops are provided at 0°
and 45°.
1
Fig. Y
2
SLIDE CUTTING WIDE BOARDS UP
TO 8 in. WIDE (FIG. AA)
WARNING
!
To avoid injury:
●
2
Never pull the cutting head
assembly and spinning blade
toward you during the cut. The
blade may try to climb up on the
top of the workpiece, causing the
cutting assembly and spinning
blade to kick back forcefully. The
cutting head assembly should
be drawn back completely then
pushed forward when sawing.
Let the blade reach full speed
before cutting. This will help
reduce the risk of a thrown
workpiece.
1
COMPOUND CUT (FIG. Z)
A compound cut is the combination of a
miter and a bevel cut simultaneously.
1. Loosen the bevel lock handle (1)
and position the cutting head at the
desired bevel position. Lock the
bevel lock handle.
●
2. Loosen the miter handle (2). Lift up
the positive stop locking lever and
position the table at the desired
angle. Release the positive stop
locking lever and lock the miter
handle.
31
To Slide Cut Wide Boards (Fig. AA)
1. Unlock the carriage lock handle
(1) and allow the cutting head
assembly to move freely.
2. Set both the desired bevel angle
and/or the miter angle and lock into
position.
CUTTING BOWED MATERIAL (FIG.
BB)
WARNING
!
To avoid injury from materials being
thrown, always unplug the saw
to avoid accidental starting and
remove small pieces of material
from the table cavity.
3. Use a hold down clamp to secure
the workpiece.
4. Grasp and pull forward the switch
handle (2) until the center of the
saw blade is over the front of the
workpiece (3).
5. Engage the trigger to turn the saw
on.
6. When the saw reaches full speed,
push the switch handle down,
slowly, cutting through the leading
edge of the workpiece.
7. Slowly move the switch handle
toward the fence, completing the
cut.
The table insert may be removed for
this purpose, but always reattach table
insert prior to performing a cutting
operation.
A bowed workpiece must be positioned
against the fence and secured with
a clamping device as shown before
cutting. Do not position workpiece
incorrectly or try to cut the workpiece
without the support of the fence. This
will cause the blade to bind and could
result in personal injury.
8. Release the trigger and allow
the blade to stop spinning before
allowing the cutting head to raise.
Fig. BB
Fig. AA
1
2
3
ROUGH CUTTING A DADO (FIG. CC)
WARNING
!
DO NOT USE A DADO BLADE, use
only the standard saw blade for this
operation.
1. Mark lines identifying the width
and depth of the desired cut on
32
the workpiece and position on the
table so the inside tip of the blade
is positioned on the line. Use a
hold down clamp to secure the
workpiece.
Fig. DD
2. Lower the cutting head so the tip of
the blade touches the top surface
workpiece at the marked line.
3. While holding the upper arm in
position, turn the stop knob (2) until
it touches the stop plate (1).
4. Cut two parallel grooves as shown
below.
3-1/4 in.
AUXILIARY WOOD FENCE (FIG. EE)
When making multiple or repetitive cuts
that result in cut-off pieces of one inch
or less, it is possible for the saw blade
to catch the cut-off piece and throw it
out of the saw or into the blade guard
and housing, possibly causing damage
or injury. To minimize this an auxiliary
wood fence can be mounted to your
saw. Holes are provided in the saw
fence to attach an auxiliary wood fence
(this provides additional depth of cut).
This fence should be constructed of
straight auxiliary wood approximately
3/4 in. thick by 1-1/2 in. high by 16 in.
long. Attach the wood fence securely
and make a full depth cut to make
a blade slot. Check for interference
between the wood fence and the lower
blade guard. Adjust if necessary.
Fig. CC
2
1
Cut these grooves
with saw
Use a chisel to cut
out the middle
Fig. EE
WORKPIECE SUPPORT (FIG. DD)
Long pieces need extra support. The
support should be placed under the
workpiece. Keep your hand holding the
workpiece positioned 6-3/4 inches or
more away from the blade. The support
must let the workpiece lay flat on the
work table during the cutting operation.
NOTE: When mounted on a flat
surface, the saw table is 3-1/4 inches
high.
Auxiliary
fence
Blade slot
33
CUTTING BASE MOLDING (FIG. FF)
Base moldings and many other
moldings can be cut on a compound
miter saw. The setup of the saw
depends on molding characteristics
and application, as shown. Perform
practice cuts on scrap material to
achieve best results:
1. Always make sure moldings rest
firmly against fence and table. Use
hold-down, crown molding vise
or C-clamps, whenever possible,
and place tape on the area being
clamped to avoid marks.
2. Reduce splintering by taping the cut
area prior to making the cut. Mark
the cut line directly on the tape.
3. Splintering typically happens due to
an incorrect blade application and
thinness of the material.
angles that, when added together,
equal exactly 90°.
Most crown molding has a top rear
angle (the section that fits flat against
the ceiling) of 52°and a bottom rear
angle (the section that fits flat against
the wall) of 38°.
In order to accurately cut crown
molding for a 90° inside or outside
corner, lay the molding with its broad
back surface flat on the saw table.
When setting the bevel and miter
angles for compound miters, remember
that the settings are interdependent;
changing one changes the other, as
well.
Fig. GG
F
e
n
c
e
Fig. FF
F
e
n
c
F
e
n
c
Miter saw table
e
e
Bevel/Miter Settings
Miter saw table
Miter saw table
miter at 00, bevel
at 450
miter at 450,
bevel at 00
Fig. HH
Settings for standard crown molding
lying flat on compound miter saw
table
NOTE: Always perform a dry run cut
so you can determine if the operation
being attempted is possible before
power is applied to the saw.
Inside corner
OR
OL
CUTTING CROWN MOLDING (FIG.
GG, HH)
IR
IL
!
WARNING
Outside corner
Your compound miter saw is suited
for the difficult task of cutting crown
molding. To fit properly, crown molding
must be compound-mitered with
extreme accuracy. The two surfaces
on a piece of crown molding that fit
flat against the ceiling and wall are at
Compound cut crown moldings
NOTE: The chart below references
a compound cut for crown molding
ONLY WHEN THE ANGLE BETWEEN
THE WALLS EQUALS 90°.
34
Bevel/Miter Settings
KEY BEVEL MITER
SETTING SETTING
TYPE OF CUT
Inside corner-Left side
IL
33.9°
33.9°
33.9°
33.9°
31.6° Right 1. Position top of molding against fence.
2. Miter table set at RIGHT 31.6°.
3. LEFT side is finished piece.
Inside corner-Right side
1. Position bottom of molding against fence.
2. Miter table set at LEFT 31.6°.
3. LEFT side is finished piece.
IR
31.6° Left
31.6° Left
Outside corner-Left side
OL
OR
1. Position bottom of molding against fence.
2. Miter table set at LEFT 31.6°.
3. RIGHT side is finished piece.
Outside corner-Right side
31.6° Right 1. Position top of molding against fence.
2. Miter table set at RIGHT 31.6°.
3. RIGHT side is finished piece.
35
CROWN MOLDING CHART
Compound Miter saw
Miter and bevel Angle settings
Wall to Crown Molding Angle
52/38° Crown Molding
45/45° Crown Molding
52/38° Crown Molding
45/45° Crown Molding
Angle
Between
Walls
Angle
Between
Walls
Miter
Setting
Bevel
Setting
Miter
Setting
Bevel
Setting
Miter
Setting
Bevel
Setting
Miter
Setting
Bevel
Setting
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
42.93
42.39
41.85
41.32
40.79
40.28
39.76
39.25
38.74
38.24
37.74
37.24
36.75
36.27
35.79
35.31
34.83
34.36
33.90
33.43
32.97
32.52
32.07
31.62
31.17
30.73
30.30
29.86
29.43
29.00
28.58
28.16
27.74
27.32
26.91
26.50
26.09
25.69
25.29
24.89
24.49
24.10
23.71
23.32
22.93
22.55
22.17
21.79
21.42
21.04
20.67
20.30
19.93
19.57
19.20
18.84
18.48
41.08
40.79
40.50
40.20
39.90
39.61
39.30
39.00
38.69
38.39
38.08
37.76
37.45
37.13
36.81
36.49
36.17
35.85
35.52
35.19
34.86
34.53
34.20
33.86
33.53
33.19
32.86
32.51
32.17
31.82
31.48
31.13
30.78
30.43
30.08
29.73
29.38
29.02
28.67
28.31
27.96
27.59
27.23
26.87
26.51
26.15
25.78
25.42
25.05
24.68
24.31
23.94
23.57
23.20
22.83
22.46
22.09
46.89
46.35
45.81
45.28
44.75
44.22
43.70
43.18
42.66
42.15
41.64
41.13
40.62
40.12
39.62
39.13
38.63
38.14
37.66
37.17
36.69
36.21
35.74
35.26
34.79
34.33
33.86
33.40
32.94
32.48
32.02
31.58
31.13
30.68
30.24
29.80
29.36
28.92
28.48
28.05
27.62
27.19
26.77
26.34
25.92
25.50
25.08
24.66
24.25
23.84
23.43
23.02
22.61
22.21
21.80
21.40
21.00
36.13
35.89
35.64
35.40
35.15
34.89
34.64
35.38
34.12
33.86
33.60
33.33
33.07
32.80
32.53
32.25
31.98
31.70
31.42
31.34
30.86
30.57
30.29
30.00
29.71
29.42
29.13
28.83
28.54
28.24
27.94
27.64
27.34
27.03
26.73
26.42
26.12
25.81
25.50
25.19
24.87
24.56
24.24
23.93
23.61
23.29
22.97
22.66
22.33
22.01
21.68
21.36
21.03
20.70
20.38
20.05
19.72
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
18.13
17.77
17.42
17.06
16.71
16.37
16.02
15.67
15.33
14.99
14.66
14.30
13.97
13.63
13.30
12.96
12.63
12.30
11.97
11.64
11.31
10.99
10.66
10.34
10.01
9.69
9.37
9.05
8.73
8.41
8.09
7.77
7.46
7.14
6.82
6.51
6.20
5.88
5.57
5.26
4.95
4.63
21.71
21.34
20.96
20.59
20.21
19.83
19.45
19.07
18.69
18.31
17.93
17.55
17.17
16.79
16.40
16.02
15.64
15.25
14.87
14.48
14.09
13.71
13.32
12.93
12.54
12.16
11.77
11.38
10.99
10.60
10.21
9.82
9.43
9.04
8.65
8.26
7.86
7.47
7.08
6.69
6.30
5.90
5.51
5.12
4.72
4.33
3.94
3.54
20.61
20.21
19.81
19.42
19.03
18.64
18.25
17.86
17.48
17.09
16.71
16.32
15.94
15.56
15.19
14.81
14.43
14.06
13.68
13.31
12.94
12.57
12.20
11.83
11.46
11.09
10.73
10.36
10.00
9.63
9.27
8.91
8.55
8.19
7.83
7.47
7.11
6.75
6.39
6.03
5.68
5.32
4.96
4.61
4.25
3.90
19.39
19.06
18.72
18.39
18.06
17.72
17.39
17.05
16.71
16.38
16.04
15.70
15.36
15.02
14.62
14.34
14.00
13.65
13.31
12.97
12.62
12.29
11.93
11.59
11.24
10.89
10.55
10.20
9.85
9.50
9.15
8.80
8.45
8.10
7.75
7.40
7.05
6.70
6.35
6.00
5.65
5.30
4.94
4.59
4.24
4.32
4.01
3.70
3.39
3.08
2.77
2.47
2.15
1.85
1.54
1.23
0.92
0.62
0.31
3.89
3.53
3.10
2.83
2.47
2.12
1.77
1.41
3.54
3.19
2.83
2.48
2.12
1.77
1.41
1.06
3.15
2.75
2.36
1.97
1.58
1.18
0.79
0.39
1.06
0.71
0.35
0.71
0.35
36
MAINTENANCE
MAINTENANCE
NOTE: To reinstall the same brushes,
first make sure the brushes go back in
the way they came out. This will avoid
a break-in period that reduces motor
performance and increases wear.
!
DANGER
To avoid injury, never put lubricants
on the blade while it is spinning.
!
WARNING
Fig. II
●
To avoid fire or toxic reaction,
never use gasoline, naphtha
acetone, lacquer thinner or
similar highly volatile solvents to
clean the miter saw.
●
●
To avoid injury from unexpected
starting or electrical shock,
unplug the power cord before
working on the saw.
For your safety, this saw is
double-insulated. To avoid
electrical shock, fire or injury,
use only parts identical to
those identified in the parts
list. Reassemble exactly as
the original assembly to avoid
electrical shock.
2
1
LOWER BLADE GUARD
Do not use the saw without the lower
blade guard. The lower blade guard is
attached to the saw for your protection.
Should the lower guard become
damaged, do not use the saw until the
damaged guard has been replaced.
Develop a regular check to make sure
the lower guard is working properly.
Clean the lower guard of any dust or
buildup with a damp cloth.
REPLACING CARBON BRUSHES
(FIG. II)
Replace both carbon brushes when
either has less than 1/4 in. length of
carbon remaining, or if the spring or
wire is damaged or burned. To inspect
or replace brushes, first unplug the
saw. Then remove the black plastic
cap (1) on the side of the motor (2).
Remove the cap cautiously, because
it is springloaded. Then pull out the
brush and replace. Replace for the
other side. To reassemble reverse the
procedure. The ears on the metal end
of the assembly go in the same hole
the carbon part fits into. Tighten the
cap snugly, but do not overtighten.
!
WARNING
●
●
When cleaning the lower guard,
unplug the saw from the power
source receptacle to avoid
unexpected startup.
Do not use solvents on the
guard. They could make the
plastic “cloudy” and brittle.
37
SAWDUST
Fig. JJ
Periodically, sawdust will accumulate
under the work table and base. This
could cause difficulty in the movement
of the worktable when setting up
a miter cut. Frequently blow out or
vacuum up the sawdust.
Central pivot of
plastic guard
!
WARNING
Chop pivot
Wear proper eye protection to keep
debris from entering eyes when
removing sawdust from unit.
Fig. KK
LUBRICATION (FIG. JJ, KK)
All the motor bearings in this tool are
lubricated with a sufficient amount of
high grade lubricant for the life of the
unit under normal operating conditions;
therefore, no further lubrication is
required.
1
Lubricate the Following as necessary:
1
Chop pivot: Apply light machine oil to
points indicated in illustration.
Central pivot of plastic guard: Use
light household oil (sewing machine
oil ) on metal-to-metal or metal-to-
plastic guard contact areas as required
for smooth, quiet operation. Avoid
excessive oil, to which sawdust will
cling.
Link: (actuates lower guard movement)
If down chop motion is hard to start, oil
link at two screws (1).
38
TROUBLESHOOTING GUIDE
!
WARNING
To avoid injury from accidental starting, always turn switch OFF and unplug
the tool before moving, replacing the blade or making adjustments.
TROUBLESHOOTING GUIDE - MOTOR
SUGGESTED CORRECTIVE
PROBLEM
PROBLEM CAUSE
ACTION
Brake does 1. Motor brushes not sealed 1. Inspect/clean/replace brushes.
not stop blade
within 10
seconds.
or lightly sticking.
2. Motor brake overheated
from use of defective or
wrong size blade or rapid
ON/OFF cycling.
See MAINTENANCE section.
2. Use a recommended blade. Let
cool down. See REMOVING
OR INSTALLING THE BLADE
section.
3. Arbor bolt loose.
4. Brushes cracked,
damaged, etc.
3. Retighten. See REMOVING
OR INSTALLING THE BLADE
section.
5. Other.
4. Replace brushes.
5. Contact Sears Service Center.
Motor does 1. Limit switch failure
1. Replace limit switch.
2. Replace brushes. See
MAINTENANCE section.
not start
2. Brush worn.
3. Fuse blown or circuit
breaker tripped on home 3. Verify there is electrical power at
panel.
the outlet.
Brush spark 1. Brush worn.
when switch 2. Other.
released.
1. Replace Brushes. See
MAINTENANCE section.
2. Contact Sears Service Center.
39
TROUBLESHOOTING GUIDE - SAW OPERATION
SUGGESTED CORRECTIVE
ACTION
PROBLEM
PROBLEM CAUSE
Blade hits table. 1. Misalignment.
1. See ADJUSTMENT -Setting
Cutting Depth section.
Angle of cut not 1. Miter table unlocked.
1. See OPERATION - Miter Angle
Adjustment section.
accurate. Can
2. Sawdust under table.
not adjust miter.
2. Vacuum or blow out dust. WEAR
EYE PROTECTION.
Cutting arm
wobbles.
1. Loose pivot points.
1. Contact Sears Service Center.
Cutting arm will 1. Pivot spring not replaced 1. Contact Sears Service Center.
not fully raise, or
blade guard
won’t fully close.
Blade binds,
jams, burns
wood.
properly after service. 2. Clean and lubricate moving
2. Sawdust build-up.
parts.
1. Improper operation.
2. Dull or warped blade.
3. Improper blade size.
1. See BASIC SAW OPERATION
section.
2. Replace or sharpen blade.
4 Wood is moving during 3. Replace with 7-1/4 in. diameter
cut.
blade.
4. Use hold down clamp to secure
workpiece to table.
Saw vibrates or 1. Saw blade not round / 1. Replace blade.
shakes.
damaged / loose.
2. Tighten arbor bolt.
2. Arbor bolt loose.
40
PARTS LIST
7-1/4 in. COMPOUND MITER SAW
MODEL NO. 137.211940
!
WARNING
When servicing use only CRAFTSMAN replacement parts. Use of any other
parts many create a HAZARD or cause product damage. Any attempt to
repair or replace electrical parts on this Miter Saw may create a HAZARD
unless repair is done by a qualified service technician. Repair service is
available at your nearest Sears Service Center.
PARTS LIST FOR SAW SCHEMATIC
I.D.
Description
TRIGGER
CORD CLAMP
COMPRESSION SPRING
COMPRESSION SPRING
COMPRESSION SPRING
SHAFT-PIVOT
DUST BAG ASS’Y
SPRING GUARD
ARBOR COLLAR
BLADE WRENCH
LINEAR MOTION BEARING
FLAT WASHER
FLAT WASHER
FLAT WASHER
FLAT WASHER
FLAT WASHER
WAVE WASHER
WAVE WASHER
C-RING
E-RING
O-RING
O-RING ROD
HEX. HD. BOLT
HEX. HD. BOLT
HEX. HD. BOLT
Size
Qty I.D.
Description
Size
Qty
1
1
1
1
3
1
1
2
1
4
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
083S
083Z
091S
0B5N
0CES
0CF5
0CV5
0DHT
0DHY
0DVJ
0HXV
0J4E
0J4F
0J4J
0J4L
0J7K
0JB0
0JBB
0JE6
1
1
1
1
1
1
1
1
2
1
2
1
1
2
1
1
2
1
1
1
1
2
1
1
1
2
3
1
3
1
2
1
2
1
1
6
6
3
2
2
2
1
4
2
1
4
1
1
1
1
1
2
1
1
1
1
1
1
27PF COMPRESSION SPRING
290M CAUTION LABEL
2B66 FENCE
2BGV NEEDLE POINTER
2BGW SLIDE PLATE
#AW
2BLG SHAFT-PIVOT
2BLL
LOCATOR PIN
2CA8 CR. RE. TRUSS HD. ROUND NECK SCREW M6*1.0-12
2CD2 COMPRESSION SPRING
2CGT SLOTTED SET SCREW
2CHF PLUNGER HOUSING ASS’Y
2CS9 CLAMP HANDLE
2DAT SCALE
2E63 ROCKER SWITCH
2K8Q WARNING LABEL
2K96 WARNING LABEL
2NQ6 RIVET
2QBG CLAMP BOLT
2RSB ARM
M6*1.0-8
φ6*13-1
φ8*16-2.5
φ10*20-2
φ12*21-2.5
3/8*29/32-5/64
#AW
#AW
#AW
#AW
0JET
2RSC BASE
2RSD TABLE
0JMM
0JNR
0JPE
0JPF
2RSF
ARM-MITER
M6*1.0-20
M6*1.0-25
M10*1.5-65
M10*1.5-25
M6*1.0-6
M8*1.25-20
M6*1.0-80
M6*1.0-20
M6*1.0-10
M3*24-10
M4*18-16
M5*16-12
M5*16-25
M4*18-25
M4*0.7-6
2RSG PLUNGER HANDLE
2RSH LOCKING HANDLE ASS’Y
0JQ3
0JQ4
0JX7
0JZN
0K41
0K5D
0K7X
0KA9
0KB7
0KBA
0KBC
0KBD
0KD5
0KD6
0KD7
0KDH
0KDJ
0KDQ
0KDT
0KDW
0KKK
0KMS
2RSJ
2RSL
PC-GUARD
CUTTER SHAFT GUARD
HEX. HD. BOLT
HEX. SOC. SET SCREW
ARBOR BOLT
2RSM TABLE INSERT (RIGHT)
2RSN TABLE INSERT (LEFT)
2RSP BRACING PLATE
2RSQ MOTOR HANDLE (TOP)
2RSR MOTOR HANDLE (DOWN)
CR. RE. PAN HD. SCREW & WASHER
CR. RE. COUNT HD. SCREW
CR. RE. TRUSS HD. ROUND NECK SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. TAPPING SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. SCREW
CR. RE. PAN HD. ROUND NECK SCREW
HEX. NUT
2RSS
2RST
CLEVIS PIN
CENTER SHAFT
2RSU COVER
2RWY VISE ASS’Y
2RX1 LEVER
2RX3 LASER PLUNGER HOUSING
2RX4 COVER
2RX5 TILT POINTER
M4*0.7-8
M4*0.7-10
M5*0.8-8
2S1E
2S4L
2S52
2S62
2S65
2S67
BLADE
M5*0.8-12
M5*0.8-35
M6*1.0-8
M6*1.0-20
M6*1.0-12
M6*1.0 T=5
M5*0.8 T=5
M8*1.25 T=8
M12*1.75 T=12
BEARING COVER
MOTOR ASS’Y
MITER BAR ASS’Y
POWER CABLE
LEAD WIRE ASS’Y
2T6A CONTROLLER ASS’Y
0KQW LOCK NUT
2T82
2T83
2T9K
SHAFT SLEEVE
TORSION SPRING
OPERATOR’S MANUAL
0KQY
0KR0
0KTQ
0KTS
0KUW
0LU2
0S1S
23NX
262V
26LU
27KY
LOCK NUT
NUT
CABLE CLAMP
CABLE CLAMP
TERMINAL
LIMIT SWITCH
COLLAR
GUARD-CORD
ANCHOR PLATE
WARNING LABEL
CLAMP BOLT
2T9N LABEL
2T9P
CAUTION LABEL
2T9Q TRADE-MARK LABEL
2T9R
2T9S
2T9T
WARNING LABEL
TRADE-MARK LABEL
TILTING SCALE
2T9U BRACKET-TILT
2T9V CAUTION LABEL
2TDV SUPPORT BRACKET
41
7-1/4 in. COMPOUND MITER SAW
SCHEMATIC
MODEL NO. 137.211940
42
7-1/4 in. COMPOUND MITER SAW
PARTS LIST FOR MOTOR
MODEL NO. 137.211940
I.D.
Description
Size
Qty
1
0HX7
0JX2
0KCP
0KNE
0QBE
0QBG
0QBK
2BMS
2BMT
2BMU
2BMX
2BN1
2DW9
2E0J
NEEDLE ROLLER BEARING
HEX. SOC. SET SCREW
CR. RE. PAN HEAD TAPPING & WASHER SCREW
HEX. NUT
M5*0.8-6
2
M5*12-60
M6*1.0 T=5
2
2
BRUSH HOLDER ASS’Y
CARBON BRUSH ASS’Y
BRUSH COVER
2
2
2
CUTTER SHAFT
1
SPACER
1
HELIX GEAR
1
FLOW GUIDE
1
MOTOR COVER
WAVE WASHER
1
1
BALL BEARING
1
2S3B
GEAR BOX
1
2S6R
2S6T
FIELD ASS’Y
1
ARMATURE ASS’Y
1
43
Get it fixed, at your home or ours!
Your Home
For expert troubleshooting and home solutions advice:
manage my home
For repair – in your home – of all major brand appliances,
lawn and garden equipment, or heating and cooling systems,
no matter who made it, no matter who sold it!
For the replacement parts, accessories and
owner’s manuals that you need to do-it-yourself.
For Sears professional installation of home appliances
and items like garage door openers and water heaters.
R
(1-800-469-4663)
1-800-4-MY-HOME
Call anytime, day or night (U.S.A. and Canada)
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service Center
(U.S.A.)
(Canada)
1-800-488-1222
1-800-469-4663
To purchase a protection agreement on a product serviced by Sears:
(U.S.A.)
(Canada)
1-800-827-6655
1-800-361-6665
Para pedir servicio de reparación
a domicilio, y para ordenar piezas:
Au Canada pour service en français:
MC
1-800-LE-FOYER
R
1-888-SU-HOGAR
(1-800-533-6937)
(1-888-784-6427)
® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC
® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio de Sears Brands, LLC
MC Marque de commerce / MD Marque déposée de Sears Brands, LLC
© Sears Brands, LLC
|