Product Safety Guide
A
(HL-L2300D / HL-L2305W / HL-L2315DW / HL-L2320D / HL-L2340DW /
HL-L2360DW / HL-L2380DW / DCP-L2520DW / DCP-L2540DW /
MFC-L2680W / MFC-L2685DW / MFC-L2700DW / MFC-L2705DW /
MFC-L2707DW / MFC-L2720DW / MFC-L2740DW)
Using the Documentation
A
Please read this guide before attempting to operate the product, or before attempting any
maintenance. Failure to follow these instructions may result in an increased risk of personal injury
or damage to property, including through fire, electrical shock, burns or suffocation. Brother shall
not be liable for damage caused where the product owner has failed to follow the instructions set
out in this guide.
Read all of the instructions. Save them for later reference.
Symbols and conventions
used in the documentation
Electrical Hazard icons alert you to
possible electrical shocks.
A
Fire Hazard icons alert you to the
possibility of a fire.
The following symbols and conventions are
used throughout the documentation.
Hot Surface icons warn you not to
touch product parts that are hot.
WARNING
WARNING indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injuries.
Prohibition icons indicate actions
that must not be performed.
Bold
Bold typeface identifiesspecific
keys on the product’s control
panel or on the computer
screen.
CAUTION
CAUTION indicates a potentially hazardous
situation which, if not avoided, may result in
minor or moderate injuries.
Italics
Italicized typeface emphasizes
an important point or refers you
to a related topic.
IMPORTANT
IMPORTANT indicates a potentially
hazardous situation which, if not avoided,
may result in damage to property or loss of
product functionality.
Courier Text in Courier New font
New
identifies messages on the
LCD of the product.
Follow all warnings and instructions marked
on the product.
NOTE
NOTE specifies the operating environment,
conditions for installation, or special
conditions of use.
NOTE
• Not all models are available in all
countries.
• The illustrations in this guide show the
HL-L2340DW and MFC-L2700DW.
Version F
USA/CAN
1
DO NOT place the product near chemicals or in a place where chemicals could be spilled on it.
Should chemicals come into contact with the product, there may be a risk of fire or electric
shock. In particular, organic solvents or liquids such as benzene, paint thinner, polish remover,
or deodorizer may melt or dissolve the plastic cover and/or cables, resulting in a risk of fire or
electric shock. These or other chemicals may also cause the product to malfunction or become
discolored.
DO NOT put the product in a location that blocks or obstructs any slot or opening in the product.
These slots and openings are provided for ventilation. Blocking the product’s ventilation could
create a risk of overheating and/or fire.
Instead:
• Keep a minimum gap around the product as shown in the illustration.
10 in.
(250 mm)
4 in.
(100 mm)
5 in.
(120 mm)
4 in.
(100 mm)
4 in.
(100 mm)
4 in.
(100 mm)
• Place the product on a solid level surface.
• DO NOT place this product near or over a radiator or heater.
• DO NOT place this product in a “built-in” installation unless adequate ventilation is provided.
DO install your product near an AC power outlet that is easily accessible. In the event of an
emergency, easy access to the plug and outlet will allow you to shut off power to the product
quickly and completely.
Plastic bags are used in the packing of your product. Plastic bags are not toys. To avoid the
danger of suffocation, keep these bags away from babies and children and dispose of them
properly.
3
CAUTION
DO NOT place any objects around the product. Such objects block the access to the power
outlet in case of emergency. It is important that the product can be unplugged whenever
needed.
The product may generate odorous gas such as ozone if used for a large volume of printing or
used in a poorly ventilated room for long hours. In addition, the product emits some chemical
substances during the printing. Ensure adequate ventilation for the product to avoid discomfort
or injury.
Avoid placing your product in a busy area. If you must place it in a busy area, ensure that the
product is in a safe location where it cannot be accidentally knocked over, which could cause
injury to you or others and serious damage to the product. Also ensure that cords are secured
so as not to pose a tripping hazard.
DO NOT place heavy objects on the product.
DO NOT place this product on an unstable cart, stand, or table, particularly if children are
expected to be near the product. The product is heavy and may fall, causing injury to you or
others and serious damage to the product. For the products with scanning function, there is an
added risk of injury if the scanner glass should break.
Put your product on a flat, level, stable surface (such as a desk), that is free from vibration and
shocks. Put the product near a telephone wall jack (MFC only) and a standard grounded AC
power outlet.
When multiple devices, including this product, are connected to a computer using USB cables,
you may feel an electric charge when you touch metal parts of the product. Avoid touching them.
IMPORTANT
• DO NOT place your product next to devices that contain magnets or generate magnetic fields.
Doing so may interfere with the operation of the product, causing print quality problems.
• DO NOT place your product next to sources of interference, such as speakers or the base units
of non-Brother cordless telephones. Doing so may interfere with the operation of the product's
electronic components.
• DO NOT connect your product to an AC power outlet controlled by wall switches or automatic
timers. DO NOT connect your product to the same circuit as a large appliance or other
equipment that requires a significant amount of electricity to operate (such as an air
conditioner, copier, or shredder). Operating this product in conjunction with other products that
require a significant amount of electricity to operate could disrupt the power supply or create
an overvoltage, tripping your circuit breaker or blowing your fuse. Disruption of the power
supply also may delete information from the product's memory, and repeated cycling of the
power supply can damage the product.
4
To use the product safely
A
Please keep these instructions for later reference and read them before attempting any
maintenance. If you do not follow these safety instructions, there is a possibility of a fire, electrical
shock, burn or suffocation.
WARNING
ELECTRICAL HAZARDS
Failure to follow the warnings in this section may create the risk of an electrical shock. In
addition, you could create an electrical short, which may create the risk of a fire.
There are high voltage electrodes inside the product. Before you access the inside of the
product, including for routine maintenance such as cleaning, make sure you have unplugged the
telephone line cord first (MFC only) and then the power cord from the AC power outlet, as well
as any telephone (RJ-11) (MFC only) or Ethernet (RJ-45) cables (Network models only) from
the product. Never push objects of any kind into this product through cabinet slots, since they
may touch dangerous voltage points or short out parts.
Unplug the power plug regularly to clean it. Use a dry cloth to clean the root of the plug blades
and between the blades. If the power plug is plugged into the outlet over a long period, dust
accumulates around the plug blades, which may cause a short circuit resulting in a fire.
DO NOT handle the plug with wet hands. Doing this might cause an electrical shock.
5
Always make sure the plug is fully inserted. DO NOT use the product or handle the cord if the
cord has become worn or frayed.
If the product has been dropped or the casing has been damaged, there may be the possibility
of an electric shock. Unplug the product from the AC power outlet and contact Brother
Authorized Service Personnel.
DO NOT allow this product to come into contact with water. This product should not be used
around standing water, including a bath tub, sink, or swimming pool; around appliances
containing water, including a refrigerator; or in a wet basement.
If water, other liquids, or metal objects get inside the product, immediately unplug the product
from the AC power outlet and contact Brother Authorized Service Personnel.
DO NOT dismantle this product. Dismantling this product could cause a fire or electric shock.
DO NOT attempt to service this product yourself. Opening or removing covers may expose you
to dangerous voltage points and other risks and may void your warranty. Refer all servicing to
a Brother Authorized Service Center.
This product should be connected to an AC power source within the range indicated on the
rating label. DO NOT connect it to a DC power source or inverter. If you are not sure what kind
of power source you have, contact a qualified electrician.
6
Power Cord Safety:
• This product is equipped with a 3-wire grounded plug. This plug will only fit into a grounded
power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, call
your electrician to replace your obsolete outlet. DO NOT attempt to defeat the purpose of the
grounded plug.
• DO NOT pull on the middle of the AC power cord; pulling on the middle may cause the cord
to separate from the plug. Doing this might cause an electrical shock.
• Only use the power cord supplied with this product (for certain models only).
• DO NOT use any undesignated cables (or optional devices). It may cause a fire or injuries.
Installation must be performed properly according to the user's guide.
• This product should be positioned so that nothing pinches or constricts the power cord.
• DO NOT allow anything to rest on the power cord.
• DO NOT place this product where people may step on the cord.
• DO NOT place this product in a position where the cord is stretched or strained, as it may
become worn or frayed.
• DO NOT use the product if the power cord is frayed or damaged. Doing so may cause an
electrical shock or fire.
• Brother strongly recommends that you DO NOT use any type of extension cord.
• DO NOT drop any metallic hardware or any type of liquid on the power plug of the product.
It may cause an electrical shock or a fire.
DO NOT use this product during an electrical storm.
(MFC only)
Use caution when installing or modifying telephone lines. Never touch telephone wires or
terminals that are not insulated unless the telephone line has been unplugged from the wall jack.
Never install telephone wiring during a lightning storm. Never install a telephone wall jack in a
location that is wet or may become wet, for example, near a refrigerator or other appliance that
produces condensation.
7
DO NOT put a toner cartridge or a toner cartridge and drum unit assembly into a fire. It could
explode, resulting in injuries.
DO NOT use flammable substances, any type of spray, or an organic solvent/liquid containing
alcohol or ammonia to clean the inside or outside of the product. Doing so could cause a fire or
electrical shock. Instead, use only a dry, lint-free cloth.
DO NOT attempt to operate this product when a paper jam or stray pieces of paper are inside
the product. Prolonged contact of paper with the fuser unit could cause a fire.
DO NOT use a vacuum cleaner to clean up scattered toner. Doing this might cause the toner
dust to ignite inside the vacuum cleaner, potentially starting a fire. Please carefully clean the
toner dust with a dry, lint-free soft cloth and dispose of it according to local regulations.
(Models with Wireless LAN function only)
DO NOT use the product near any medical electrical equipment. The radio wave emitted from
the product may affect medical electrical equipment and cause a malfunction, which may result
in a medical accident.
8
For persons with a pacemaker
The product emits weak electromagnetic waves. Should you feel something is wrong, move
away from the product and consult with a medical doctor immediately.
DO NOT place the following objects on the product. If these objects contact the electrical parts
inside the product, it may cause a fire or electric shock.
• Metal object such as a clip or a staple
• Precious metal such as a necklace or a ring
• Container holding water or liquid such as a glass, a flower vase or a flower pot
HOT SURFACE
After you have just used the product, some internal parts of the product will be extremely hot.
Wait at least 10 minutes for the product to cool down before you touch the internal parts of the
product.
If the product becomes unusually hot, releases smoke, generates any strong smells, or if you
accidentally spill any liquid on it, immediately unplug the product from the AC power outlet.
Contact Brother Authorized Service Personnel.
9
CAUTION
(Products with scanning function only)
When you move the product, grasp the side handholds that are under the scanner. DO NOT
carry the product by holding it at the bottom. If you do not carry the machine properly, the
machine could slip out of your hands, and injury could result.
(Products with scanning function only)
Some areas of the product can cause injury if covers (shaded) are closed with force. Take care
when placing your hand in the areas shown in the illustrations, and DO NOT close the covers
with force.
(Products with scanning function only)
To prevent injuries, be careful not to put your fingers in the areas shown in the illustrations.
For your safety, unplug the product from the power outlet when not used for a long time.
10
DO NOT try to open a toner cartridge. If the toner powder leaks out, avoid inhaling it or letting it
come in contact with your skin.
Keep the toner cartridge out of the reach of children. If a child swallows the toner powder,
consult a doctor immediately.
We recommend placing the toner cartridge and drum unit assembly on a clean, flat surface with
disposable paper underneath it in case you accidentally spill or scatter toner. If toner scatters
on your hands or clothes, immediately wipe or wash it off with cold water.
Should you come into contact with toner, follow these instructions:
• Inhalation
Obtain immediate medical attention. In case of accidental inhalation, move to fresh air
immediately, then obtain medical attention.
• Skin contact
Remove contaminated clothing immediately and wash affected skin with plenty of water or
soap and water.
• Eye contact
Obtain medical attention. If the toner has gotten into the eyes, immediately wash out the eyes
with water continuously, for at least 15 minutes.
• Ingestion
Obtain immediate medical attention. Wash out mouth with water and drink 200 - 300 ml (half
a pint) of water.
For more safety information regarding the toners used in your product, please visit the following
DO NOT run your hand over the edge of the printing paper. The thin and sharp edge of the paper
may cause an injury.
11
IMPORTANT
• DO NOT remove or damage any of the caution or warning labels inside the product.
200°C
396°F
200°C/396°F
• DO NOT put objects on top of the product. Doing so could increase the risk of overheating
should the product malfunction.
12
Important safety instructions
A
1 Read all of these instructions.
2 Save these instructions for later reference.
3 Follow all warnings and instructions marked on the product.
4 Unplug this product from the AC power outlet and refer all servicing to Brother Authorized
Service Personnel under the following conditions:
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate normally when the operating instructions are followed.
Adjust only those controls that are discussed in the operating instructions. Improper
adjustment of other controls may result in damage and will often require extensive work by
a qualified technician to restore the product to normal operation.
If the product exhibits a distinct change in performance, indicating a need for service.
5 For the location of your nearest Brother Authorized Service Center, please contact:
In USA: 1-877-BROTHER (1-877-276-8437)
13
Regulation
A
WARNING
(MFC only)
When using your telephone equipment, basic safety precautions should always be followed to
reduce the risk of fire, electrical shock, and injury to people. These important safety precautions
include the following:
1 DO NOT use this product near water or locations that may become wet, for example, near a
bath tub, wash bowl, kitchen sink or washing machine, in a wet basement or near a
swimming pool.
2 Avoid using this product during an electrical storm. There may be a remote risk of an electric
shock from lightning.
3 DO NOT use this product to report a gas leak in the vicinity of the leak.
4 Use only the power cord provided with the product.
Read all of the instructions. Save them for later reference.
(MFC only)
To reduce the risk of shock or fire, use only a No. 26 AWG or larger telecommunication line cord.
Disconnect device
This product must be installed near an AC power outlet that is easily accessible. In case of an
emergency, you must unplug the power cord from the AC power outlet to shut off the power
completely.
14
Standard telephone and FCC notices (MFC only)
A
These notices are in effect on models sold and used in the United States only.
When programming emergency numbers or making test calls to emergency numbers:
Remain on the line and briefly explain to the dispatcher the reason for the call before hanging
up.
Perform these activities in the off-peak hours, such as early morning or late evening.
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the
ACTA. On the backside of this equipment is a label that contains, among other information, a
product identifier in the format US: AAAEQ##TXXXX. If requested, this number must be provided
to the telephone company.
You may safely connect this equipment to the telephone line by means of a standard modular jack,
USOC RJ11C.
A plug and jack used to connect this equipment to the premises wiring and telephone network
must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A
compliant telephone cord and modular plug is provided with this product. It is designed to be
connected to a compatible modular jack that is also compliant. (See installation instructions for
details.)
The REN is used to determine the number of devices that may be connected to a telephone line.
Excessive RENs on a telephone line may result in the devices not ringing in response to an
incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined by the total RENs,
contact the local telephone company. For products approved after July 23, 2001, the REN for this
product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits
represented by ## are the REN without a decimal point (e.g., 06 is a REN of 0.6). For earlier
products, the REN is separately shown on the label.
If this equipment causes harm to the telephone network, the telephone company will notify you in
advance that temporary discontinuance of service may be required. But if advance notice is not
practical, the telephone company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations or procedures
that could affect the operation of the equipment. If this happens the telephone company will
provide advance notice in order for you to make necessary modifications to maintain uninterrupted
service.
If trouble is experienced with this equipment, for repair or warranty information, please contact
Brother Customer Service (see Basic User's Guide: Brother numbers). If the equipment is causing
harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
Connection to party line service is subject to state tariffs. Contact the state public utility
commission, public service commission or corporation commission for information.
If your home has specially wired alarm equipment connected to the telephone line, ensure the
installation of this equipment does not disable your alarm equipment. If you have questions about
what will disable alarm equipment, call your telephone company or a qualified installer.
15
If you are not able to solve a problem with your product, contact Brother Customer Service
(see Basic User's Guide: Brother numbers).
WARNING
For protection against the risk of electrical shock, always disconnect all cables from the wall
outlet before the equipment is installed, serviced, or modified.
DO NOT attempt to service this product yourself. Refer all servicing to a Brother Authorized
Service Center.
IMPORTANT
• This equipment may not be used on coin service lines provided by the telephone company or
connected to party lines.
• Brother cannot accept any financial or other responsibilities that may be the result of your use
of this information, including direct, special or consequential damages. There are no
warranties extended or granted by this document.
• This product has been certified to comply with FCC standards, which are applied to the USA
only. A grounded plug should be plugged into a grounded AC power outlet after checking the
rating of the local power supply for the product to operate properly and safely.
16
Federal Communications Commission (FCC) Declaration of
Conformity (USA only)
A
Responsible Party:
Brother International Corporation
200 Crossing Boulevard
Bridgewater, NJ 08807-0911 USA
TEL: (908) 704-1700
declares, that the products
Product Name: Mono Laser Printer
Model Numbers: HL-L2300D / HL-L2305W / HL-L2315DW / HL-L2320D / HL-L2340DW /
HL-L2360DW
Product Name: Multi Function Printer
Model Numbers: HL-L2380DW / DCP-L2520DW / DCP-L2540DW / MFC-L2680W /
MFC-L2685DW / MFC-L2700DW / MFC-L2705DW / MFC-L2707DW / MFC-L2720DW /
MFC-L2740DW
comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Call the dealer or an experienced radio/TV technician for help.
(Wireless network models only)
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
IMPORTANT
• Changes or modifications not expressly approved by Brother Industries, Ltd. could void the
user’s authority to operate the equipment.
• A shielded interface cable should be used to ensure compliance with the limits for a Class B
digital device.
17
RF Exposure Notice (USA or Canada only)
(Wireless models only)
A
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled
environment and meets the FCC radio frequency (RF) Exposure Guidelines and RSS-102 of the
IC radio frequency (RF) Exposure rules. This equipment should be installed and operated keeping
the radiator at least 20 cm or more away from person’s body.
Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour un
environnement non contrôlé et respecte les lignes directrices d'exposition aux fréquences
radioélectriques (RF) de la FCC et les règles d’exposition aux fréquences radioélectriques (RF)
CNR-102 de l’IC. Cet équipement doit être installé et utilisé en gardant une distance de 20 cm ou
plus entre le radiateur et le corps humain.
Wireless connection (Mexico only)
A
The operation of this equipment is subject to the following two conditions:
(1) it is possible that this equipment or device may not cause harmful interference, and (2) this
equipment or device must accept any interference, including interference that may cause
undesired operation.
La operación de este equipo está sujeta a las siguientes dos condiciones:
(1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o
dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operación no
deseada.
Industry Canada Compliance Statement (Canada only)
A
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject
to the following two conditions: (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne
doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
18
EQUIPMENT ATTACHMENT LIMITATIONS (Canada only)
(MFC only)
A
NOTICE
This product meets the applicable Industry Canada technical specifications.
Le présent materiel est conforme aux spécifications techniques applicables d’Industrie Canada.
NOTICE
The Ringer Equivalence Number is an indication of the maximum number of devices allowed to
be connected to a telephone interface. The termination on an interface may consist of any
combination of devices subject only to the requirement that the sum of the RENs of all the devices
does not exceed five.
L’indice d’équivalence de la sonnerie (IES) sert à indiquer le nombre maximal de terminaux qui
peuvent être raccordés à une interface téléphonique. La terminaison d’une interface peut
consister en une combinaison quelconque de dispositifs, à la seule condition que la somme
d’indices d’équivalence de la sonnerie de tous les dispositifs n’excède pas 5.
19
Laser safety (For 110-120V Models Only)
A
This equipment is certified as a Class 1 laser product as defined in IEC60825-1:2007
specifications under the U.S. Department of Health and Human Services (DHHS) Radiation
Performance Standard according to the Radiation Control for Health and Safety Act of 1968. This
means that the equipment does not produce hazardous laser radiation.
Since radiation emitted inside the equipment is completely confined within protective housings
and external covers, the laser beam cannot escape from the product during any phase of user
operation.
FDA regulations (For 110-120V Models Only)
A
U.S. Food and Drug Administration (FDA) has implemented regulations for laser products
manufactured on and after August 2, 1976. Compliance is mandatory for products marketed in the
United States. One of the following labels on the back of the product indicates compliance with
the FDA regulations and must be attached to laser products marketed in the United States.
Manufactured:
BROTHER INDUSTRIES (VIETNAM) LTD.
Phuc Dien Industrial Zone Cam Phuc Commune, Cam giang Dist Hai Duong Province, Vietnam
This product complies with FDA performance standards for laser products except for deviations pursuant
to Laser Notice No. 50, dated June 24, 2007.
WARNING
Use of controls, adjustments or performance of procedures other than those specified in this
manual may result in hazardous invisible radiation exposure.
Internal laser radiation
Max. Radiation Power: 25 mW
Wave Length: 770 - 800 nm
Laser Class: Class 3B
20
For use in the USA or Canada only
A
These products are made for use in the USA and Canada only. We cannot recommend using
them overseas because it may violate the Telecommunications Regulations (MFC models only)
of that country and the power requirements of your product may not be compatible with the power
available in foreign countries. Using USA or Canada models overseas is at your own risk and may
void your warranty.
LAN connection (Network models only)
A
CAUTION
DO NOT connect this product to a LAN connection that is subject to over-voltages.
21
Trademarks
A
BROTHER is either a trademark or a registered trademark of Brother Industries, Ltd.
Microsoft, Windows, Windows Vista, Windows Server, Outlook, SharePoint, Internet Explorer and
Windows Phone are either registered trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Apple, Macintosh, Safari, Mac OS, iPad, iPhone, iPod touch and OS X are trademarks of Apple
Inc., registered in the United States and other countries.
AirPrint is a trademark of Apple Inc.
Linux is the registered trademark of Linus Torvalds in the U.S. and other countries.
UNIX is a registered trademark of The Open Group in the United States and other countries.
Intel is a trademark of Intel Corporation in the U.S. and/or other countries.
Adobe, PostScript and PostScript 3 are either registered trademarks or trademarks of Adobe
Systems Incorporated in the United States and/or other countries.
Wi-Fi, Wi-Fi Alliance and Wi-Fi Protected Access are registered trademarks of Wi-Fi Alliance.
WPA, WPA2, Wi-Fi Protected Setup, Wi-Fi Protected Setup logo and Wi-Fi Direct are trademarks
of Wi-Fi Alliance.
Flickr is a registered trademark of Yahoo! Inc.
AOSS is a trademark of Buffalo Inc.
Android, Google Cloud Print, Google Drive, Picasa Web Albums and Google Play are trademarks
of Google, Inc. Use of these trademarks are subject to Google Permissions.
Nuance and PaperPort are trademarks or registered trademarks of Nuance Communications, Inc.
or its affiliates in the United States and/or other countries.
Mozilla and Firefox are registered trademarks of the Mozilla Foundation.
EVERNOTE is a trademark of Evernote Corporation and used under a license.
Each company whose software title is mentioned in this manual has a Software License
Agreement specific to its proprietary programs.
Any trade names and product names of companies appearing on Brother products, related
documents and any other materials are all trademarks or registered trademarks of those
respective companies.
22
Open Source Licensing Remarks
A
This product includes open-source software.
Licensing Remarks and Copyright information.
Copyright and License
A
©2017 Brother Industries, Ltd. All rights reserved.
This product includes software developed by the following vendors:
©1983-1998 PACIFIC SOFTWORKS, INC. ALL RIGHTS RESERVED.
©2008 Devicescape Software, Inc. All rights reserved.
This product includes the “KASAGO TCP/IP” software developed by ZUKEN ELMIC, Inc.
Other Information
A
®
FlashFX is a registered trademark of Datalight, Inc.
®
FlashFX Copyright 1998-2010 Datalight, Inc.
U.S.Patent Office 5,860,082/6,260,156
®
FlashFX Pro™ is a trademark of Datalight, Inc.
Reliance™ is a trademark of Datalight, Inc.
®
Datalight is a registered trademark of Datalight, Inc.
Copyright 1989-2010 Datalight, Inc., All Rights Reserved
23
Legal limitations for copying (Products with
scanning function only)
A
Reproductions of certain documents are illegal and may result in either criminal or civil liability.
The listing below is intended to be a guide rather than a complete listing of every possible
prohibition. In case of doubt, we suggest that you consult with the appropriate authority or advisor
with regard to the specific document.
The following documents issued by the United States/Canadian Government or any of its
Agencies, States, Territories or Provinces may not be copied:
Money
Bonds or other certificates of indebtedness
Certificates of Deposit
Internal Revenue Stamps (canceled or uncanceled)
Selective Service or draft papers
Passports
United States/Canadian Postage Stamps (canceled or uncanceled)
Food Stamps
Immigration Papers
Checks or drafts drawn by Governmental agencies
Identifying badges or insignias
Licenses and Certificates of Title to motor vehicles, under certain State/Provincial law
Copying copyrighted works may be regulated by Federal, State or local laws. For more
information, consult an appropriate authority or advisor.
24
Month of publication: 02/2019
|