Color Laser Printer HL-2400Ce series
Quick Setup Guide
Read this Setup Guide before setting up the printer.
Before using the printer, you must completely set up all hardware and install the driver.
❏
Identify the Operating System on your computer (Windows® 3.1x, 95/98, Windows NT® 4.0 or Macintosh)
❏ Purchase the appropriate interface cable for your computer (Parallel, Serial, Network Interface)
❏ Follow the instructions in this guide for your operating system and cable interface.
Components may differ from one country to another. Save all packing materials and
the printer carton. They should be saved for re-use when shipping the printer.
Components
OPC Belt Cartridge
Printer
Fuser Cleaner
Power Cord
Standard Media Cassette
Toner Cartridges
(pre-installed)
(Black, Cyan, Magenta and Yellow)
Oil Bottle
CD-ROM includes : Printer driver
Oil Syringe
Fonts
User's Guide
Instructional Video
Other Software
Printer Reference Guide
Quick Setup Guide
CD-ROM
✒ Note
It is ESSENTIAL that you keep all packing materials for transporting or storing the printer later. Failure
to empty, clean and correctly repack the printer according to the manufacturer's instructions before
shipment will result in serious damage to the printer that may not be covered by the printer warranty.
General View
Controller Box
Top Cover
Control Panel
Front Cover
Power Button
Power Cord Connector
Rear Access Cover
Media Cassette
Rear Side Cover
LJ2083001
Printed in Japan
Step 3 Install the Toner Cartridges
After rocking each toner cartridge 3 to 4 times,
remove the orange protective cover from the
toner cartridges.
Pull off the tape labeled 'REMOVE' from the
toner cartridge.
Close the Front Cover.
Install the 4 toner cartridges by sliding each of
them into the correct guide.
Step 4 Install the Oil Bottle and Fuser Cleaner
Release the Fusing unit pressure a little by
pushing the Pressure Release Levers to the
OPEN position. (1). Pull the orange protective
parts fitted between the rollers of the Fusing
Unit and remove them (2). Make sure that the
Pressure Release Levers are put back to the
SET position.
Install the Oil Bottle into the Fusing Unit with
the label side facing the front of the printer.
Set the Fuser Cleaner into the Fusing Unit with
the roller side facing you.
Lock the Oil Bottle and the Fuser Cleaner in
place by turning the Oil Bottle Lock Levers.
Close the Top Cover.
Step 5 Load Paper in the Media Cassette
Pull the Media Cassette out of the printer.
Adjust the Paper Guides to accommodate the
paper size you want to load. Hold the shaded
parts shown below to move the guides.
Load paper into the Media Cassette.
Reinsert the Media Cassette into the printer.
Step 6 Test Print
When the following LCD message appears,
press the Sel button to take the printer off-
line.
Plug in the power cord and turn the printer on.
Wait until the printer initializes.
LJ READY 001P T1
AUTO
■ ■ ■ ■
K C M Y
Hold down the Shift button and press the Test
button then release both buttons.
Press the ▲ or ▼ button to scroll through the
display until the desired message appears.
Choose from one of the following selections:
To Print
the Demonstration Page
the Test Pattern
LCD Message
DEMO PAGE
TEST PRINT
the list of printer settings
the list of internal or resident fonts
the list of optional card fonts
the list of permanent download fonts
PRINT CONFIG
PRINT FONTS I
PRINT FONTS C
PRINT FONTS P
Press the Set button and the printer will print
the selected item.
Some models may have NC-3100h pre-installed. For settings information please see the
Network User's guide on the CD-ROM.
To install the printer driver, please refer to the CD-ROM supplied with the printer.
✒ Note
A real time clock is built into this printer. Set the time referring to the user's guide on the CD-ROM.
You need to set the time before you can use the log management and fax functions.
©2000 Brother Industries, Ltd. Windows and Windows NT are registered trademarks of Microsoft Corporation in the U.S. and other countries. Macintosh and iMac are
registered trademarks of Apple Computer, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
|