FAX-202
FAX-222
FAX-333MC
®
Setup Receive .................................................................................. 5-1
Record FAX/TEL Outgoing Announcement (F/T OGM)
ii
Setting Up Sequential Polling Receive
®
Setting Multi-Function Link Mode
(With Multi-Function Link option) ............................... 5-9
Setup Send ...................................................................................... 6-1
Composing Electronic Cover Page
Cover Page for Next Fax Only
Composing Your Own Comments
Print Sample Call Back Message (For FAX-222/333MC
iii
Storing One Touch Dial Numbers/Storing Junk Fax/Call
Storing Speed Dial Numbers/Storing Junk Fax/Call
Setting Up Groups for Broadcasting (For FAX-333MC
Answering Calls with the Speakerphone
iv
Copy Options: Single or Multiple Copies, Sort/Stack
v
Specifications .................................................................................. S-1
Using Remote Retrieval Access Code (For FAX-333MC
vi
1
Introduction
1
Using This Manual
Thank you for purchasing a Brother fax machine. This fax machine has been designed
to be simple to use, with LCD screen prompts to guide you through functions.
However, you can use your fax machine to its fullest potential by taking a few minutes
to read this manual.
Additionally, your fax machine has a Help Key. Press Copy/Help and then press
Start to print a list of basic operational steps and functions.
Finding Information
All chapter headings and subheadings are listed in the Table of Contents. You will be
able to find information about a specific feature or function by checking the Index at
the back of this manual. Also, throughout this manual, you’ll see special symbols
alerting you to important information, cross-references, and warnings. Illustrations of
some screen displays also help you choose the correct key-presses.
About fax machine
If you’re a first-time fax machine user, fax operation might seem a little mysterious.
You’ll soon get used to the unusual fax tones on your phone line, and be able to send
and receive faxes easily.
I N T R O D U C T I O N
1 - 1
Fax Tones and Handshake
When someone is sending a fax, the fax machine sends fax calling tones (CNG
tones)—soft, intermittent beeps at 4-second intervals. You’ll hear them when you dial
and press Start, and they continue for about 40 seconds after dialing. During that
time, the sending machine must begin the “handshake” with the receiving machine.
Each time you use automatic procedures to send a fax, you are sending CNG tones
over the phone line. You’ll soon learn to listen for these soft beeps each time you
answer a phone on your fax line, so you know if you are receiving a fax message.
The receiving fax responds with fax receiving tones—loud, chirping sounds. A
receiving fax chirps for about 40 seconds over the phone line, and the screen displays
RECEIVE. If your fax machine is set to the FAX ONLY Mode, it will answer every
call automatically with fax receiving tones. Even if the other party hangs up, your fax
machine continues to send the “chirps” for about 40 seconds, and the screen continues
to display “RECEIVE”. To cancel the receiving mode, press Stop.
When your fax machine answers in FAX/TEL Mode, the fax machine listens for CNG
tones and then responds with receiving tones.
The fax “handshake” is the time in which the sending machine’s CNG tones and the
receiving machines “chirps” overlap. This must be for at least 2 to 4 seconds, so the
machines can understand how each is sending and receiving the fax. The handshake
cannot begin until the call is answered, and the CNG tones only last for about 40
seconds after the number is dialed. Therefore, it’s important for the receiving machine
to answer the call in as few rings as possible.
When you have an external telephone answering device (TAD) on your fax line, your
TAD will determine the number of rings before the call is answered. Pay special
attention to the directions in the Installation chapter for connecting a TAD to your fax
machine.
ECM (Error Correction Mode) (For FAX-333MC Only)
The Error Correction Mode (ECM) is a way for the fax machine to check the integrity
of a fax transmission while it is in progress. ECM transmissions are possible only
between machines that both have the ECM feature. If they do, you may send and
receive fax messages that are continuously checked for their integrity.
Sufficient memory must be available in your fax machine for this feature to work.
1 - 2
I N T R O D U C T I O N
FAX-202 and FAX-222 Control Panel Overview
1
14
13
12
2
3
4
5
6
7
8
9
10
11
1 LCD (Liquid Crystal
Display)
6 Dial Pad
Dials phone and fax
numbers, and can be used
as a keyboard for entering
information into the fax
machine.
11 Start
Starts an operation, such
as sending a fax.
Displays messages to help
you set up and
operate your fax machine.
12 Resolution
Sets the resolution when
you send a fax or make a
copy.
2 Hold
7 One Touch Dial Keys
These four keys give you
instant access to
previously stored phone
numbers.
Lets you put calls on hold.
Also, lets you view or
print the Caller ID list.
(For Singapore and Hong
Kong only)
13 Function/Set
Lets you access the
function and
programming mode.
Also, stores a function
setting into the fax
machine.
3 Redial/Pause
8 Stop
Re-dials the last number
called. Also inserts a
pause in autodial numbers.
Stops a fax, cancels an
operation or exits from
Function mode.
14
(Left Arrow)
4 Search/Speed Dial
Lets you dial stored phone
numbers by pressing #
and a two-digit number.
Also lets you look up
numbers stored in the
dialing memory.
9 Mode
(Right Arrow)
Use to select how fax
machine will handle
incoming calls.
Volume
Moves the LCD cursor to
the left or right. Adjusts
speaker and ring volume.
10 Copy/Help
Makes a copy. If no
originals are in the
ADF, it prints a quick
reference Help List.
5 Hook
Lets you dial
telephone and fax
numbers without lifting
the handset.
I N T R O D U C T I O N
1 - 3
FAX-333MC Control Panel Overview
18
17
16
15
1
14
13
2
3
4
5
12
6
7
8
9
10
11
6 Dial Pad
Dials phone and fax
numbers, and can be used
as a keyboard for entering
information into the fax
machine.
7 One Touch Dial Keys
These four keys give you
instant access to
previously stored phone
numbers.
13 Function/Set
1 LCD (Liquid Crystal
Display)
Lets you access the
function and programming
mode.
Also, stores a function
setting into the fax machine.
Displays messages to help
you set up and
operate your fax machine.
2 Hold
14
(Left Arrow)
(Right Arrow)
Lets you put calls on hold.
Also, lets you view or
print the Caller ID list.
(For Singapore and Hong
Kong only)
Volume
Moves the LCD cursor to
the left or right. Adjusts
speaker and ring volume.
8 Stop
3 Redial/Pause
Stops a fax, cancels an
operation or exits from
Function mode.
15 Microphone
Re-dials the last number
called. Also inserts a
pause in autodial numbers.
Picks up your voice when
you speak to another party
using speakerphone.
9 Mode
4 Search/Speed Dial
Lets you dial stored phone
numbers by pressing #
and a two-digit number.
Also lets you look up
numbers stored in the
dialing memory.
Use to select how fax
machine will handle
incoming calls.
16 MC ON/OFF
Lets you activate the
Message Center.
Also, notifies you that you
have voice or fax
10 Copy/Help
Makes a copy. If no
originals are in the
ADF, it prints a quick
reference Help List.
messages in the memory.
17 Play/Record
5 Speaker Phone
Lets you speak to the
person at the other end
and dial telephone
numbers without lifting
the handset.
Lets you listen to voice
messages and print fax
messages stored in memory.
Also, lets you record
telephone calls.
11 Start
Starts an operation, such
as sending a fax.
12 Resolution
Sets the resolution when
you send a fax or make a
copy.
18 Erase
Lets you delete voice
messages, fax messages or
all messages.
1 - 4
I N T R O D U C T I O N
2
Location and Connections
2
Caution
1
2
Never install telephone wiring during a lightning storm.
We recommend that this product be used with a surge protection device to protect the
product against lightning storms.
3
4
Never install a telephone jack in a wet location unless the jack is specifically designed
for a wet location.
Never touch telephone wires or terminals that are not insulated unless the telephone
line has been disconnected at the network interface.
5
6
Use caution when installing or modifying telephone lines.
Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
7
8
Do not use the telephone to report a gas leak in the vicinity of the leak.
For PLUGGABLE EQUIPMENT, the socket-outlet should be installed near the
equipment and should be easily accessible.
Packing List
Check that you have the following items:
Document Support
One Touch
Name Label
Telephone
Line Cord
One Starter Roll
of Recording Paper
(LETTER up to 25 pages,
A4 up to 24 pages)
Telephone
Handset
Handset
Curled Cord
Owner’s
Manual
Paper Guide
Keep the packing materials for possible future transport. If you do not pack the
machine properly, it may void your warranty.
L O C A T I O N A N D C O N N E C T I O N S
2 - 1
Choosing a Location
Place your fax machine on a flat, stable surface, such as a desk. Select a place that is
free of vibration and shocks. Locate the fax machine near a telephone jack and a
standard, grounded power outlet.
Avoid placing your machine in a high-traffic area. Do not place near heaters, air
conditioners, water, chemicals or refrigerators. Do not expose the fax machine to
direct sunlight, excessive heat, moisture or dust. Do not connect your machine to
electrical outlets controlled by wall switches or automatic timers. Disruption of power
can wipe out information in the unit’s memory. Do not connect your machine to
electrical outlets on the same circuit as large appliances or other equipment that might
disrupt the power supply. Avoid interference sources, such as speakers or the base
units of cordless phones.
Assembly
Load the recording paper
1
Open the cover by
placing your finger in the
groove under the cover
and lifting up.
2
3
Pull up the blue release lever so you can remove the three protective sheets (initial set
up) or any paper remaining in the machine from the last roll.
Unwrap the new recording paper roll and insert it into the paper bin, with the paper
feeding from the bottom of the roll.
Limited to
2.76 inches (70 mm)
2 - 2
L O C A T I O N A N D C O N N E C T I O N S
When you use 210mm recording paper roll size...
There are two different types of recording paper roll size (216mm/210mm). If you use
210mm recording paper roll size, please set recording paper after attaching the paper
guides as below.
Paper Guide
Paper Guide
Setting position
4
Raise the paper enough to pass it
over the until it feeds out the front
of the machine. Make sure there is
no slack.
5
Pull down the blue lever and close
the cover.
L O C A T I O N A N D C O N N E C T I O N S
2 - 3
About Brother Paper
For the best print quality, use Brother Therma Plus Paper, Item Numbers 6890 (two
98’ rolls) or 6840 (four 98’ rolls). Therma Plus paper is thicker, like plain paper, and
produces the best print quality.
The recording paper roll size for your fax machine is limited to a diameter of 2.76
inches (70 mm). You can use a 164’ roll of thinner thermal paper as long as it meets
these requirements.
Connectious
Connecting the Machine
Connect the handest, power cord, and telephone line.
EXT.
LINE
EXT.
PC I/F
Telephone
Line Cord
EXT.
LINE
Handset
Curled Cord
* PC I/F jack is for use
with the Brother Multi-
Function Link option. If
PC I/F
you have not purchased
this option then ignore
this part.
2 - 4
L O C A T I O N A N D C O N N E C T I O N S
1
Connect the handset
Connect the curled handset cord to the bottom of the handset and the side of the fax
machine.
2
3
Connect the power cord.
Connect the telephone line.
Connect one end of the telephone line cord to the jack labeled LINE on the left side
of the machine. Connect the other end to a modular wall jack.
WARNING
■ This machine must be grounded using a three-prong plug.
■ Since the machine is grounded through the power outlet, you can protect yourself from
potentially hazardous electrical conditions on the telephone line by keeping the power
to your machine on when you connect it to a telephone line. When you want to move
your machine, protect yourself by disconnecting the telephone line first, and then the
power cord.
■ Lightning and power surges can damage this product! We recommend that you use a
quality surge protection device on the AC power line as well as on the telephone line,
or unplug the lines during a lightning storm.
Attach the document support
Attach the document support as shown in the illustration below.
Document
Support
PC I/F
EXT.
LINE
L O C A T I O N A N D C O N N E C T I O N S
2 - 5
Multi-Line Connections (PBX)
Most offices use a central telephone system. While it is often relatively simple to
connect the fax machine to a key system or a PBX (Private Branch Exchange), we
suggest that you contact the company that installed your telephone system and ask
them to connect the fax machine for you. It is advisable to have a separate line for the
fax machine. You can then leave the fax machine in FAX ONLY Mode to receive
faxes any time of day or night.
If the fax machine is to be connected to a multi-line system, ask your installer to
connect the unit to the last line on the system. This prevents the unit from being
As with all fax units, this machine must be connected to a two wire system. If your
line has more than two wires, proper connection of the fax machine cannot be made.
If you are installing the fax machine to work with a PBX:
1
2
3
It is not guaranteed that the unit will operate correctly under all circumstances with a
PBX. Any cases of difficulty should be reported first to the company that handles your
PBX.
If all incoming calls will be answered by a switchboard operator, it is recommended
that the Answer Mode be set to MANUAL. All incoming calls should initially be
regarded as telephone calls.
The unit may be used with either pulse or tone dialing telephone service.
Custom Features on a Single Line
If you have Call Waiting, Ring Master, Voice Mail, an answering service, alarm
system or any other custom feature on your telephone line, it may create a problem in
the operation of your fax machine.
2 - 6
L O C A T I O N A N D C O N N E C T I O N S
Connecting an External Telephone Answering Device
(TAD)
(TAD Cannot Be Connected in Some Countries)
Sequence
You might choose to connect an additional answering system. When you have an
external TAD on the same telephone line as the fax machine, the TAD answers all
calls. The fax machine “listens” for fax calling (CNG) tones. If it hears them, the fax
machine takes over the call and receives the fax. If it doesn’t hear CNG tones, the fax
machine lets the TAD continue playing your outgoing message so your caller can
leave you a voice message.
The TAD must answer within four rings (the recommended setting is two rings). The
fax machine cannot hear CNG tones until the TAD has answered the call, and with
four rings there are only 8–10 seconds of CNG tones left for the fax “handshake.”
Make sure you carefully follow instructions in this manual for recording your
outgoing message. We do not recommend using the toll saver feature on your external
answering machine if it exceeds 4 rings.
Do not connect a TAD elsewhere on the same phone line—your fax machine and
TAD will both try to control the line.
PC I/F
EXT.
LINE
L O C A T I O N A N D C O N N E C T I O N S
2 - 7
Connections
The external TAD must be plugged into the back of the fax machine, into the jack
labeled EXT. Your fax machine cannot work properly if you plug the TAD into a wall
jack.
1
2
Plug the telephone line cord from the wall jack into the left side of the fax machine, in
the jack labeled LINE.
Plug the telephone line cord from your TAD into the left side of the fax machine, in
the jack labeled EXT. (Make sure this cord is connected to the TAD at the TAD’s
telephone line jack (not to telephone set jack).)
3
Set your external TAD to four rings or less. (The fax machine’s Ring Delay setting
does not apply.)
4
5
6
7
Record the outgoing message (see below).
Set the TAD to answer calls.
See Message Storage (Function/Set, 8, 1) to VOICE:EXT. (For FAX-333MC only)
Set the Answer Mode to MC:MSG CTR. (For FAX-333MC only)
On the FAX-202 or FAX-222, set the Answer Mode to TAD:ANSWER MACH.
Outgoing Message (OGM)
Timing is important in recording this message. The message sets up the ways to handle
both manual and automatic fax reception.
1
Record 5 seconds of silence at the beginning of your message. (This allows your fax
machine time to listen for the fax CNG tones of automatic transmissions before they
stop.)
2
3
Limit your speaking to 20 seconds.
End your 20-second message by giving your Fax Receive Code for people sending
manual faxes. For example:
“After the beep, leave a message or send a fax by pressing 5 1 and Start.”
Connecting an External Telephone
Your fax machine is equipped with a handset that you can use as a regular phone.
However, you can also connect a separate telephone (or telephone answering device)
directly to your fax machine.
Connect the modular plug on the telephone’s line cord to the jack labeled EXT. on the
back of the fax machine.
Whenever this phone (or TAD) is in use, the screen displays EXT. TEL IN USE, and,
if the fax machine handset is lifted, an alarm sounds. To disconnect the call and switch
to the fax machine, press Hook or Speaker Phone.
External Telephone can not be connected in some countries.
2 - 8
L O C A T I O N A N D C O N N E C T I O N S
3
On-Screen Programming
3
User-Friendly Programming
We have designed your fax machine with on-screen programming and a Help key.
User-friendly programming helps you take full advantage of all the functions your fax
Since your fax programming is done on the LCD, we created step-by-step on-screen
prompts to help you program your fax machine. All you need to do is follow the
prompts as they guide you through the function menu selections and programming
options and settings.
Function Mode
You can access the function mode by pressing Function/Set. When you enter the
function mode, your fax machine displays a list of main menu options from which you
can choose. These options appear one after the other on the display. Select a menu
option by pressing Function/Set when the option appears on the screen. The display
will scroll the options within that menu.
You can “scroll” more quickly through options by pressing
. When the screen
displays your selection, press Function/Set. (Press to scroll backward if you
passed your choice or to save key strokes. Both arrow keys show all options, in the
opposite order.)
Before you press Function/Set after entering information in a field using the dial
pad, you can correct a mistake. Use
characters.
to back up and then type over the incorrect
When you finish a function, the screen displays ACCEPTED.
If you want to exit the Function mode, press Stop.
Alternating Displays
When you see alternating displays, the LCD sometimes alternates between the
currently selected option, and a help message giving brief instructions about how to
proceed. The display you’ll probably see most often is shown below, showing you,
when you place an original in the ADF, that you can dial a number and send a fax, or
you can make a copy.
FAX: NO. & START
COPY: PRESS COPY
O N - S C R E E N P R O G R A M M I N G
3 - 1
Function Selection Table
If you have a basic understanding of how to program your fax machine, you can
perform most of the programming settings without the Owner’s Manual. To help you
understand the function selections, options, and settings that are found in your fax
programs, use the Function Selection Table below.
1. INITIAL SETUP
Function
Description
Factory Set
More Info
1. DATE/TIME
Enter date and time for LCD
display and to print on
transmissions.
—
2. STATION ID
Program name, fax number and
telephone number to appear on
each transmitted page.
—
3. BEEPER
Adjust volume level of beeper.
Selects dialing mode.
LOW
4. TONE/PULSE
TONE
2. SETUP RECEIVE
Function
Description
Factory Set
More Info
1. RING DELAY
Number of rings before fax
machine answers in FAX/TEL,
FAX, or MC mode.
RING DELAY:04
TOLL
SAVER:OFF
(FAX-333MC only)
2. F/T RING TIME
3. EASY RECEIVE
4. REMOTE CODE
Sets the time for “double ring”
in FAX/TEL mode.
20
Receive fax messages without
pressing the Start key.
ON
ON
Enter code to activate or
deactivate machine from a
remote location or to transfer
voice call from DECT cordless
phone to the machine.
(
51, # 51,
81)
5. POLLING RX
Sets up your fax machine to poll
another fax machine.
OFF
6. MELODY SETUP
(FAX-333MC only)
You can change rings to a
melody.
SIGNAL
7. MF LINK
Fax Receive Only/PC
PC Primary
Primary/PC Receive Only.
3 - 2
O N - S C R E E N P R O G R A M M I N G
3. SETUP SEND
Function
Description
Factory Set
More Info
1. COVERPG SETUP
(FAX-222/333MC Only)
Automatically sends a cover
page you program.
OFF
2. COVERPAGE MSG
(FAX-222/333MC Only)
Program customized message
for fax cover page.
—
AUTO
STANDARD
OFF
3. CONTRAST
Change lightness or darkness of
a fax you are sending.
4. RESOLUTION
5. OVERSEAS MODE
Allows you to change
resolutions page by page.
Adjusts for sometimes difficult
overseas transmissions
6. CALL RESERVE
(FAX-222/333MC Only)
You can send a fax, then speak.
OFF
7. DELAYED FAX
8. POLLED TX
Send originals later.
—
Sets up your fax machine with
an original to be retrieved by
another fax machine.
OFF
9. MEMORY TX
(FAX-333MC Only)
You can send faxes from memory
.
OFF
4. CANCEL JOB
Function
Description
Factory Set
More Info
Cancel a delayed fax or polling
job.
5. INTERRUPT
Function
Description
Factory Set
More Info
Send a fax now, even if you
have the machine set to send a
fax later, or if you have it set for
Polling.
6. SET AUTO DIAL
Function
Description
Factory Set
More Info
1. ONE-TOUCH DIAL
Dial numbers stored in memory
by pressing only one key.
—
2. SPEED-DIAL
Dial numbers stored in memory
by pressing only four keys.
—
—
3. SETUP GROUPS
(For FAX-333MC Only)
Set up a Group number for
broadcasting.
O N - S C R E E N P R O G R A M M I N G
3 - 3
7. PRINT REPORTS
Function
Description
Factory Set
More Info
1. XMIT REPORT
2. ACT.REPORT
OFF
INTERVAL:
OFF or 24H
3. AUTO DIAL
Print lists and reports of
activity.
—
4. TEL. INDEX
(Details in Chapter 11)
—
—
—
5. USER SETTINGS
6. MEMORY STATUS
(For FAX-333MC Only)
8. SETUP MSG CTR (FAX-333MC Only)
Function
Description
Factory Set
More Info
1. MSG STORAGE
Select if memory will store
fax,voice or both.
FAX:OFF
VOICE:ON
2. BACKUP PRINT
3. OGM
Prints copy of faxes received
into memory.
ON
9-4
Select/Record outgoing
message.
MSG CTR
OGM
4. ICM MAX. TIME
5. ICM REC. MONITR
6. FAX FWD/PAGING
Select maximum length of
incoming messages.
30 seconds
Adjust speaker volume for
voice messages as they come in.
ON
Set fax machine to forward fax/
message––OR––to call your
pager.
OFF
7. REMOTE ACCESS
Set code for retrieving
messages.
159
9-8
0. TEL SERVICE
Function
Description
Factory Set
More Info
1. DISTINCTIVE
(For Singapore and
Hong Kong only)
Use with phone company
Distinctive Ring service to
register the ring pattern with fax
machine.
OFF
2. KEY LOCK
Prohibits most functions except
Receiving faxes into memory.
OFF
3 - 4
O N - S C R E E N P R O G R A M M I N G
4
Initial Setup
4
Getting Started
Setting Dialing Mode (Tone/Pulse)
Your fax machine comes set to accommodate tone (multi-frequency) dialing service.
If you have pulse (rotary) dialing service, you need to change the dialing mode.
1
Press Function/Set, 1, 4.
DIALING:TONE?
DIALING:PULSE?
2
3
Use
or
to select TONE or PULSE and
press Function/Set.
Press Stop to exit.
Setting Date and Time
Your fax machine displays the date and time, and prints it on every fax you send.
In the event of a power failure, you may have to reset the date and time. All other
settings remain unaffected.
1
2
Press Function/Set, 1, 1.
ENTER YEAR:XX
Enter the last two digits of the year and press
Function/Set.
ENTER MONTH:XX
3
Enter two digits for the month and press
Function/Set. (For example, enter 09 for
ENTER DAY:XX
September, or 10 for October)
4
5
6
Enter two digits for the day and press
Function/Set. (For example, 06)
ENTER TIME:XX:XX
Enter the time in 24-hour format and press Function/Set. (For example, enter 15:25
for 3:25 PM)
Press Stop. The screen now displays the date and time you set, and displays it
whenever the fax machine is in Standby mode.
There are two different types of this display. One shows MONTH/DAY/YEAR, the
other shows DAY/MONTH/YEAR.
I N I T I A L S E T U P
4 - 1
Setting Station ID
You can store your name, fax number, and telephone number to be printed on all fax
pages.
1
2
Press Function/Set, 1, 2.
FAX:
Enter your fax number (up to 20 digits) and press
Function/Set.
TEL:
3
Enter your telephone number (up to 20 digits) and
NAME:
press Function/Set. If your telephone number and
fax number are the same, enter the same number
again. The screen displays your entry.
4
5
Use the dial pad to enter your name (up to 20 characters) and press Function/Set.
(You can use the chart on next page to help you enter letters.)
Press Stop. The screen returns to the date and time.
In Turkey, user cannot register the Station ID because of PTT regulation. Please
contact Brother fax dealer to register your ID.
Details for Entering Text
When you are setting certain functions, such as the Station ID, you may need to enter
text into the fax machine. Most keys on the dial pad have three or four letters printed
above them. The keys for 0, # and don’t have printed letters because they are used
for special characters or operations.
By pressing the appropriate number on the dial pad the correct number of times, you
can access the character you want.
Press Key
one time
two times
three times
four times
2
3
4
5
6
7
8
9
A
D
G
J
B
E
C
F
2
3
4
5
6
S
8
Z
H
K
N
Q
U
X
I
L
O
R
V
Y
M
P
T
W
Inserting spaces
If you want to enter a blank space, press
twice.
4 - 2
I N I T I A L S E T U P
Making corrections
If you entered a letter incorrectly and want to change it, press
to move the cursor
after the last correct letter. Then press Stop; the letters above and to the right of the
cursor are deleted. Re-enter the correct text and/or digits. You can also back up and
type over incorrect letters.
Repeating letters
If you need to enter a character assigned to the same key as the previous character,
press
to move the cursor to the right.
Special characters and symbols
Press , # or Ø repeatedly to move the cursor under the special character or symbol
you want, then press
to select it.
Press for (space) ! “ # $ % & ’ ( ) + , - . /
*
Press # for : ; < = > ? @ [ ] ^ _
Press Ø for É À È Ê Î Ç Ë Ö 0
NOTICE
The Telephone Consumer Protection Act of 1991 makes it unlawful for
any person to use a computer or electronic device to send any message
via a telephone fax machine unless such messages clearly contain, in a
margin at the top or bottom of each transmitted page, or on the first page
of the transmission, the date and time it is sent and an identification of the
business or other entity or other individual sending the message and the
telephone number of the sending machines or such business, other entity
or individual.
In order to program this information into your fax machine, you should
■ The telephone number you enter is used only for Call Back Message and Cover
Page features.
■ If you do not enter a fax number, no additional information can be entered.
■ To enter a space, press
once between numbers and twice between characters.
■ If your Station ID has already been programmed, the screen prompts “1” to make
a change, or “2” to exit without changing.
I N I T I A L S E T U P
4 - 3
Setting Beeper Volume
You can set the beeper to LOW, HIGH or OFF. The default setting is LOW. When
the beeper is set to LOW or HIGH, the fax machine beeps every time you press a key
or make an error, and at the end of fax sending or receiving.
1
2
3
Press Function/Set, 1, 3.
Press
or
to select your setting and press Function/Set.
Press Stop to exit.
Setting the Speaker Volume
You can adjust the speaker volume when your fax machine is on hook (after you
pressed Hook or Speaker Phone), by selecting a speaker volume level.
Press
or
to adjust the volume level. The display shows the setting you are
choosing. Each key press changes the volume to the next setting. The new setting will
remain until you change it again.
If you have FAX-333MC, you can adjust the speaker volume while you are listening
to your OGM (Outgoing Message) and ICMs (incoming messages).
If you turn Incoming Recording Monitor to OFF (Function/Set, 8, 5) on the
FAX-333MC, the Speaker for screening calls will be disabled and you won’t hear
callers leaving messages. The volume for other operations can still be controlled
using
and
.
Setting the Ring Volume
You can adjust the ring volume when your fax machine is idle. You can select a ring
volume level or press until the ring is off.
Press
or
to adjust the volume level. With each key press, the fax machine
rings so you can hear the current setting and the display shows the setting you are
choosing. Each key press changes the volume to the next setting. The new setting will
remain until you change it again.
Memory Storage
In the event of a power failure, all settings in the INITIAL SETUP, SETUP
RECEIVE, SET AUTO DIAL, REMOTE FAX OPT and SETUP MSG CTR plus the
COVERPG SETUP and COVERPAGE MSG (from SETUP SEND) functions are
stored permanently. You may have to reset the date and time.
4 - 4
I N I T I A L S E T U P
Key Lock System
This feature allows you to prevent unauthorised access to the fax machine. When
switched ON, Key Lock System prohibits most functions. The following functions
listed are available while Key Lock System is switched ON.
■ Receiving faxes
■ Answering Calls
■ Scheduled Delayed Transmission*
■ Polling*
■ Fax Forwarding*
■ Remote Retrieval
* Provided it was set before Key Lock System was switched ON.
®
Even if you set up the Multi-Function Link optional software, printing and scanning
are not available while Key Lock System is switched ON.
Using Key Lock System
You must use a password to switch Key Lock System ON and OFF.
Setting Up the Key Lock System for the First Time
1
Press Function/Set, 0, 2.
NEW PASSWD:XXXX
ENTER & SET
The screen prompts you to enter the password,
and then press Function/Set.
2
3
Enter a 4-digit number as a new password.
Press Function/Set.
The screen prompts you re-enter the password.
VERIFY:XXXX
ENTER & SET
4
5
Re-enter the password and press
Function/Set.
The screen displays
SET KEY LOCK
SET PASSWORD
6
7
Press
or
to choose SET KEY LOCK.
Press Function/Set. The screen prompts you
to enter the password.
PASSWORD:XXXX
ENTER & SET
8
Enter a 4-digit password, followed by
Function/Set.
This is the same as the password of your machine already stored.
The screen displays ACCEPTED for 2 seconds, followed by KEY LOCK MODE -
Key Lock System is now switched ON.
I N I T I A L S E T U P
4 - 5
If the password you enter at Step 8 is incorrect, the screen would display WRONG
PASSWORD. After 2 seconds the display will then return to normal (displaying the
date & time). You must then try again to switch Key Lock System ON.
Changing the Key Lock System Password
1
2
3
Press Function/Set, 0, 2.
SET KEY LOCK
Press
or
to choose SET PASSWORD.
SET PASSWORD
Press Function/Set.
The screen prompts you to enter the old
password.
OLD PASSWD:XXXX
ENTER & SET
4
5
Enter the current password.
Press Function/Set.
The screen prompts you to enter the new
password.
NEW PASSWD:XXXX
ENTER & SET
6
7
Enter a 4-digit number as a new password.
Press Function/Set.
The screen prompts you to re-enter the new
password.
VERIFY:XXXX
ENTER & SET
8
9
Enter the new password again and press Function/Set.
Press Stop to exit.
Switching Key Lock System ON
1
2
3
Press Function/Set, 0, 2. The screen displays
SET KEY LOCK
SET PASSWORD
Press
or
to choose SET KEY LOCK.
Press Function/Set. The screen prompts you
to enter the password.
PASSWORD:XXXX
ENTER & SET
4
Enter a 4-digit password, followed by
Function/Set.
This is the same as the password of your machine already stored.
The screen displays ACCEPTED for 2 seconds, followed by KEY LOCK MODE -
Key Lock System is now switched ON.
If the password you enter at Step 4 is incorrect, the screen would display WRONG
PASSWORD. After 2 seconds the display will then return to normal (displaying the
date & time). You must then start from Step 1 to set Key Lock System.
4 - 6
I N I T I A L S E T U P
Switching OFF Key Lock System
1
2
When Key Lock System is switched ON, press
Function/Set.
The screen prompts you to enter the password,
followed by Function/Set.
PASSWORD:XXXX
ENTER & SET
Enter a 4-digit password and press Function/Set.
The screen displays ACCEPTED, then after 2 seconds the display reverts to normal.
Key Lock System is now switched OFF.
If the password you enter at Step 2 is incorrect, the screen would display WRONG
PASSWORD. After 2 seconds the display will then return to displaying KEY LOCK
MODE. You must then start from Step 1 to switch OFF Key Lock System.
If you forget the Key Lock System password, please contact your Brother dealer for
service.
I N I T I A L S E T U P
4 - 7
5
Setup Receive
5
Basic Receiving Operations
Select Answer Mode
MANUAL—You must answer all calls yourself. If you hear fax tones, press Start to
begin receiving the fax, then hang up. You can use this mode with Distinctive Ringing.
FAX ONLY—The fax machine automatically answers every call as a fax call. You
cannot receive a voice call, but you can dial out and make a voice call.
FAX/TEL—The fax machine automatically answers every call. If the call is a fax, it
prints the fax. If the call is not a fax, it signals you with a F/T pseudo-ring, different
from the phone company ringing, to alert you to pick up the call. If you select this
setting, you’ll need to set the Ring Delay and F/T Ring Time features (on the following
TAD (For FAX-202/222 only)—This is the only setting in which you can use an
external answering machine. Your telephone answering device is connected to your
FAX, and answers every call. Once the TAD answers, the FAX listens for fax tones.
If it detects fax tones, it prints the fax.
The TAD setting works only with an external telephone answering device (TAD); it
does not work with telephone company voice mail. Ring Delay and F/T Ring Time
do not work in this setting.
TAD can not be connected in some countries.
NIGHT (For FAX-202 and FAX-222)––This is the Night Mode setting. The fax
machine receives incoming fax calls without ringing. In case of a voice call, the fax
machine does not ring and it doesn’t receive the voice call. The caller hears fax tones
after few rings.
NIGHT (For FAX-333MC only)––If you set the receiving mode to Night,
MC ON/OFF button is automatically turned on. The fax machine receives incoming
fax calls without ringing. In the event of voice call, the incoming voice call is stored
in the message manager memory. As the ICM recording monitor (for call screening)
is automatically set to OFF, the user is not disturbed by the voice of the caller. In case
of memory full, the machine change to F/T mode if the machine still has paper. It
changes to Manual mode if it both memory full and out of paper.
If you have not recorded the Outgoing Message for Message Center mode (See
chapter 9), your fax machine does not receive the voice call.
Night mode overrides the receiving mode set by the user. In the morning, the user
must press Mode to manually revert to the Answer mode they have set (such as F/T
or FAX ONLY).
5 - 1
S E T U P R E C E I V E
MSG CTR (For FAX-333MC only)—The fax machine provides you with a built-in
digital Message Center for fax and voice. When you set the machine to answer calls,
it will record up to 15 minutes of messages. For more information about Message
FAX ONLY
FAX/TEL
ANSWER MACH.
(For FAX-202/222 only)
MNL
NGT
:
:
MANUAL
NIGHT
Current Answer Mode
MSG CTR
(For FAX-333MC only)
To select or change your Answer Mode
1
Press Mode. The screen displays your current selection.
The options on the FAX-202/222 are:
FAX ONLY
FAX/TEL
TAD:ANSWER MACH.
MANUAL
NIGHT
S E T U P R E C E I V E
5 - 2
The options on the FAX-333MC are:
FAX ONLY
FAX/TEL
MANUAL
NIGHT
Or, if Message Center Mode is ON, it overrides your
Answer Mode Setting, so the display shows:
MC:MSG CTR
2
Continue to press Mode until your new selection appears. After 2 seconds, the screen
returns to the date and time display, along with your new Answer Mode setting.
If you’re changing Answer Mode while in another operation, the screen returns to the
current operation display.
Setting Ring Delay
The Ring Delay setting determines the number of times the fax machine rings before
1
2
3
Press Function/Set, 2, 1. If you have a FAX-202 or FAX-222, go to Step 3.
Press
or
to select RING DELAY and press Function/Set.
Press
or
to select how many times the line rings before the fax machine
answers (00 – 04 or 00 – 10) and press Function/Set. If you select 00, the line
doesn’t ring at all.
4
Press Stop to exit.
Setting Melody for Rings (FAX-333MC only)
You can select a favorite music out of 4 choices for rings. If you select a melody for
rings, the melody will be played when the machine received a telephone call or fax
message.
The default setting is SIGNAL.
1
Press Function/Set, 2, 6.
SIGNAL
SELECT <- -> & SET
2
3
Press
or
to select SIGNAL, MELODY 1, MELODY 2, MELODY 3,
MELODY 4 or SINGLE and press Function/Set.
Press Stop to exit.
Even if you select a melody for rings, F/T pseudo-ring can not be changed to the
melody.
5 - 3
S E T U P R E C E I V E
Setting F/T Ring Time
You need to determine how long the fax machine will notify you with its special F/T
pseudo-ring when you have a voice call. It will ring happens after the initial ringing
from the phone company. Only the fax machine rings for 20, 30, 40 or 70 seconds; no
other phones on the same line ring the special F/T pseudo-ring. However, you can
answer the call on any phone (in a separate wall jack) on the same line as the fax
machine.
1
2
Press Function/Set, 2, 2.
Press
or
to select how long the fax machine
RING TIME:20 SEC
will ring to alert you that you have a voice call and
press Function/Set.
3
Press Stop to exit.
Now, when a call comes in and the machine is set to FAX/TEL Mode, all phones on
this line will ring the number of times you selected in Ring Delay.
You can let the fax machine pick up and detect if it’s a fax or voice call. If it’s a fax
call, the machine prints the fax. If it’s a voice call, the machine signals you with a
F/T pseudo-ring for the length of time you selected in F/T Ring Time.
Even if the caller hangs up during the F/T pseudo-ring, the fax machine continues for
the set time.
Record FAX/TEL Outgoing Announcement (F/T OGM)
(For FAX-333MC only)
This is the announcement played by your fax machine (not an external TAD) when
someone calls and your machine is set to FAX/TEL mode. Although callers hear your
announcement, they cannot leave a message. To erase the announcement, follow the
1
Press Function/Set, 8, 3. The screen prompts you to choose F/T OGM, MSG CTR
OGM or PAGING MSG.
2
3
Press
Press
or
or
to select F/T OGM (not MSG CTR OGM) and press Function/Set.
to select RECORD OGM? and press Function/Set.
Then pick up the handset to record a message.
Replace the handset. Your OGM is played.
Press Stop to exit.
4
5
S E T U P R E C E I V E
5 - 4
Easy Receive
When you use this feature, you don’t have to press Start when you answer a fax call
and hear calling beeps. Just hold the handset and wait a few seconds. When you see
RECEIVE on the fax screen or when you hear “chirps” through the handset of an
extension phone connected to another wall jack, just replace the handset, and your
machine does the rest. Selecting ON allows the fax machine to receive fax calls
automatically, even if you lift the handset of an extension or external phone. Selecting
SEMI lets the machine receive the call only if you’ve answered it at the fax machine.
Selecting OFF means you’ll have to activate the fax machine yourself, by pressing
Start or by pressing 5 1 if you are not at your machine. (See Operation from
If you’ve set the feature to ON, but your fax machine doesn’t automatically connect a
fax call when you lift an external or extension phone handset, press the Fax Receive
code 5 1. At the fax machine, lift the handset and press Start.
1
2
3
Press Function/Set, 2, 3.
Press
or
to select ON, SEMI or OFF and press Function/Set.
Press Stop to exit.
External Telephone can not be connected in some countries.
5 - 5
S E T U P R E C E I V E
Advanced Receiving Operations
Operation from External or Extension Telephone
If you answer a fax call on an extension phone or on an external phone in the EXT.
jack, you can make your fax machine take over by using the Fax Receive Code. When
If the fax machine answers a voice call and F/T pseudo-ring for you to take over, use
If you answer a call, and no one is on the line, assume you’re receiving a fax. At the
fax machine phone, press Start, then hang up. At an extension phone, press 5 1,
wait for fax receiving tones (chirps), then hang up. At an external phone, press
5 1 and wait for the phone to be disconnected (the screen displays RECEIVE)
before you hang up. (Your caller will have to press Start to send the fax.)
External phone can not be connected in some countries.
For FAX/TEL Mode Only
When the fax machine is in FAX/TEL mode, it will use the F/T Ring Time (F/T
pseudo-ring) to alert you to a voice call. If you’re at the fax machine, you can lift the
handset to answer.
If you’re at an extension phone, you’ll need to lift the handset during the F/T Ring
Time and press # 5 1 between the F/T pseudo-ring. If no one is on the line, or if
someone wants to send you a fax, send the call back to the fax machine by pressing
5 1.
Remote Call Transfer (Semi-DECT Management)
This function works when you receive the incoming Voice call at the remote DECT
cordless phone externally connected to the fax machine. You can transfer voice call to
the fax machine. But you can not transfer the incoming voice call from the fax
machine to the DECT cordless phone.
To transfer telephone call to the fax machine
When you pick up the voice call at remote DECT cordless phone and would like to
transfer it to the fax machine,
1
2
Press Activation Voice Code 8 1 at remote cordless phone.
The fax machine rings (pseudo-ring same as current F/T ring) and the display shows
“CALL PICKUP”.
3
Pick up the handset and press Hook or Spesker Phone —OR—just press
Spesker Phone at the fax machine in order to transfer the voice call to the fax
machine.
S E T U P R E C E I V E
5 - 6
Don’t hang up the call from the cordless phone until the voice call has been
transferred to the fax machine. You will know when this is because you will no longer
be able to hear or talk to the caller via the cordless phone. If you do not wait until this
point before hanging up from the cordless phone, the call will be lost.
If nobody answers at the fax machine, pseudo-ringing stops after 30 seconds. In that
case, it may still be possible to speak with the caller from the cordless phone. Speech
between the fax machine and the cordless phone (= intercom) is not possible.
Changing Remote Codes
Remote Codes might not work with some telephone systems. The preset Fax Receive
Code is 5 1. The preset Telephone Answer Code is # 5 1.
If you are always disconnected when accessing your external TAD remotely, try
changing the Fax Receive Code from 5 1 to # # # and the Telephone Answer Code
from # 5 1 to 9 9 9.
1
2
Press Function/Set, 2, 4.
Press
or
to select ON (or OFF) and press
REMOTE ACT.:ON?
Function/Set.
3
4
5
6
If you want to, enter a new Fax Receive Code, then
press Function/Set.
*
FAX RECEIVE: 51
If you want to, enter a new Telephone Answer
Code, then press Function/Set.
TEL ANSWER:#51
ACT.VOICE:*81
If you want to, enter a new Activation Voice Code,
then press Function/Set.
Press Stop to exit.
Polling
Polling is the process of retrieving faxes from another fax machine. You can use your
fax machine to “poll” other machines, or you can have someone poll your machine.
All parties involved in polling need to set up their fax machines to accommodate
polling. When someone polls your machine to receive a fax, they pay for the call; if
you poll someone’s fax machine to receive a fax, you pay for the call.
Some fax machines do not respond to the polling function.
5 - 7
S E T U P R E C E I V E
Setting Up Polling Receive
Polling Receive is when you call another fax machine to receive a fax from it.
1
Press Function/Set, 2, 5.
The screen displays:
POLLING RX:OFF?
SELECT <- -> & SET
2
3
Press
or
to choose ON.
Press Function/Set. The screen prompts you
to enter the fax number you want to poll, and
then to press Start.
ENTER FAX NO.
PRESS START KEY
4
5
Enter the fax number you are polling.
Press Start. The screen displays DIALING.
Setting Up Delayed Polling Receive
1
2
3
Press Function/Set, 2, 5. The screen
displays:
POLLING RX:OFF?
SELECT <- -> & SET
Press
or
to choose TIMER
POLLING?.
Press Function/Set.
The screen prompts you to enter the time you
want to begin polling.
SET TIME=15:25
4
5
6
7
Enter the time (in 24-hour format) you want to begin polling. For example, enter 21:45
for 9:45 PM.
Press Function/Set. The screen prompts you
to enter the fax number to be polled.
ENTER FAX NO.
PRESS START KEY
Enter the fax number (you can use One Touch
or Speed Dial, or dial manually).
Press Start. The fax machine makes the polling call at the time you entered.
This function is not available in some countries.
S E T U P R E C E I V E
5 - 8
Setting Up Sequential Polling Receive
(For FAX-333MC Only)
Your fax machine can request documents from several fax units in a single operation.
Afterward, a Sequential Polling Report will be printed.
1
Press Function/Set, 2, 5.
The screen displays:
POLLING RX:OFF?
SELECT <- -> & SET
2
3
Press
or
to select Polling ON.
POLLING RX:ON?
Press Function/Set. The screen prompts you
to enter the fax numbers to be polled.
ENTER FAX NO.
PRESS START KEY
4
5
Specify the destination fax machines you wish
to poll, using One Touch, Speed Dial or a
Group.
Press Start.
ACCEPTED
DIALING
Your fax machine will poll each number or
group member in turn for an original.
®
Setting Multi-Function Link Mode
®
(With Multi-Function Link option)
If you connect your fax machine to your PC, you can receive faxes into your PC.
®
®
Multi-Function Link , you can select Multi-Function Link Mode (PC Primary/PC
Receive Only/Fax Receive Only) for routing incoming faxes.
1
2
Press Function, 2, 7.
7.MF LINK
Press
or
to select PC PRIMARY, PC
RECEIVE ONLY or FAX RECEIVE ONLY.
Press Set when the screen displays your selection.
Press Stop to exit.
3
4
®
For Middle East Countries, Multi-Function Link Pro is available, which works with
English and Arabic Windows 95/98 and NT w.s. ver4.
®
®
The Multi-Function Link and Multi-Function Link Pro are optional accessories.
Please check with the dealer or distributor in your country.
5 - 9
S E T U P R E C E I V E
6
Setup Send
6
Automatic Document Feeder (ADF)
■ Originals must be between 5.8 and 8.5 inches (148 and 216 mm) wide, and 5.9 and
23.7 (150 and 600 mm) inches long. Your fax machine can only scan an image 8.2
inches (208 mm) wide, regardless the paper width.
■ Make sure you place the original face down, top edge first.
■ Adjust the paper guides to fit the width of your original.
Paper guides
ADF (Automatic Document Feeder)
The automatic document feeder (ADF) can hold up to 10 pages, feeding each one
individually through the fax machine. Use standard (17 lb–24 lb) paper when using
the ADF; if you’re using heavier paper, feed each sheet individually to prevent paper
jams.
DO NOT use curled, wrinkled, folded or ripped paper, or paper with staples, paper
clips, paste or tape attached. DO NOT use cardboard, newspaper or fabric.
■ Make sure originals written with ink are completely dry.
S E T U P S E N D
6 - 1
Manual Transmission
Manual transmission lets you hear the dial tone, ringing and fax receiving tones before
sending the fax.
1
2
Place the original face down in the ADF.
Pick up the handset and listen for a dial tone
—OR—press Hook or Speaker Phone and listen for a dial tone.
3
Enter the fax number you want to call. (You can enter the digits using the dial pad, or
you can enter a One Touch or Speed Dial number or you can call using
4
5
When you hear the fax tone, press Start.
If you’re using the handset, hang up.
Automatic Transmission
This is the easiest way to send a fax.
IMPORTANT: Do not pick up the handset, or press Hook or Speaker Phone.
1
2
Place the original face down in the ADF.
Enter the fax number using One Touch, Speed Dial, Search or the dial pad. (See One
3
Press Start.
Manual and Automatic Fax Redial
If you’re sending a fax manually and the line is busy, press Redial/Pause to retry the
number.
If you’re sending a fax automatically and the line is busy, the fax machine will redial
automatically up to three times or ten times.
Memory Transmission (For FAX-333MC Only)
This feature allows your machine to scan a fax into its memory and send it as soon as
the scan is complete. This way, you don’t have to wait for the entire fax to be
transmitted before you retrieve your original.
1
2
3
Place the original face down in the ADF.
Press Function/Set, 3, 9.
9.MEMORY TX
To change the default setting, press
to select ON (or OFF) and press
or
MEMORY TX:ON?
SELECT <- >- & SET
Function/Set. Go to Step 5—OR—For the
next fax transmission only, press or to
select NEXT FAX ONLY and press Function/Set.
4
For the next fax only, press
press Function/Set.
or
to select ON (or OFF) and
6 - 2
S E T U P S E N D
5
6
Press 1 to select additional settings. The display returns to the
SETUP SEND menu—OR—Press 2 if you are finished choosing settings
and go to Step 6.
Enter fax number and press Start.
If you get a OUT OF MEMORY message while scanning the first page of a fax, press
Stop to cancel the scan. If you get a OUT OF MEMORY message while scanning in
a subsequent page, you’ll have the option to press Start to transmit the pages scanned
so far, or to press Stop to cancel the operation. In this case, send the fax by the
Manual Transmission.
Depending on your typical faxes, OUT OF MEMORY errors can occur frequently. If
this happens, change the Memory Transmission setting back to OFF.
Basic Sending Operations
Composing Electronic Cover Page
(For FAX-222/333MC Only)
The cover page is generated at the receiving party’s machine. Your cover page
includes the name stored in the One Touch or Speed Dial memory. If you’re dialing
The cover page indicates the fax is from your Station ID, and the number of pages
you’re sending. If you have Coverpage Setup set to ON (Function/Set 3 1), the
Most of the SETUP SEND functions are temporary settings that allow you to make
adjustments for each original you send. However, so that you can set up your cover
page and cover page comments in advance, the Cover Page Setup and Cover Page
Message functions will change their default settings.
You can select a comment to include on your
cover page.
1.COMMENT OFF
2.PLEASE CALL
Instead of using one of the comments above,
you can enter up to two customized messages,
3.URGENT
each 27 characters long. Use the chart on page
25 to help enter characters.
4.CONFIDENTIAL
S E T U P S E N D
6 - 3
Cover Page for Next Fax Only
(For FAX-222/333MC Only)
does not work without the Station ID.
You can set the fax to send a cover page with a particular original. This cover page
will include the number of pages in your original.
1
2
3
4
5
6
Place the original in the ADF.
Press Function/Set, 3, 1.
When the screen displays NEXT FAX ONLY?, press Function/Set.
Press
or
to select ON.
Press Function/Set.
Press
or
to view the comment
1.COMMENT OFF
2.PLEASE CALL
3.URGENT
selections.
7
8
Press Function/Set when the screen displays
your selection.
4.CONFIDENTIAL
5.(USER DEFINED)
Enter two digits to indicate the number of
pages your are sending. (Enter 0 0 to leave the
number of pages blank.) If you make a
6.(USER DEFINED)
mistake, press
to back up and reenter the
number of pages.
9
Press Function/Set. The screen displays:
ACCEPTED
10 Press 1 if you want to select additional
settings. The display returns to the Setup Send
menu—OR—Press 2 if you are finished
choosing settings, and go to Step 11.
OTHER SETTINGS?
1.YES 2.NO
11 Enter the fax number you’re calling.
12 Press Start.
Always Send Cover Page (For FAX-222/333MC Only)
not work without the Station ID.
You can set the fax machine to send a cover page whenever you send a fax. The
number of pages in your fax is not included when you use this setting.
1
2
3
Press Function/Set, 3, 1.
Press
or
to select.
COVERPAGE:OFF?
COVERPAGE:ON?
Press Function/Set when the screen displays
COVERPAGE:ON?. (If you select ON, a
coverpage is always sent when you send a fax.)
6 - 4
S E T U P S E N D
4
If you selected ON, you must select a
comment. Press or to view possible
selections. (You can select your custom
comment.)
1.COMMENT OFF
2.PLEASE CALL
3.URGENT
4.CONFIDENTIAL
5.(USER DEFINED)
6.(USER DEFINED)
ACCEPTED
5
6
Press Function/Set when the screen displays
your selection. The screen displays:
OTHER SETTINGS?
1.YES 2.NO
Press 1 if you want to select additional
settings. The display returns to the Setup Send
menu—OR—Press 2to exit if you are finished
choosing settings.
Using a Printed Cover Page (For FAX-222/333MC Only)
If you prefer using a printed cover page that you can write on, you can print the sample
page and attach it to your fax.
1
2
3
4
Press Function/Set, 3, 1.
Press
or
to select PRINT SAMPLE?.
Press Function/Set when the screen displays your selection.
Press Start. Your fax machine prints a copy of your cover page.
- - -
- - -
- - -
COVER PAGE
- - -
TO:
FROM:
FAX:
TEL:
PAGE[S] TO FOLLOW
COMMENT:
Cover Page Message (For FAX-222/333MC Only)
You can set up two custom comments.
S E T U P S E N D
6 - 5
Composing Your Own Comments
(For FAX-222/333MC Only)
1
2
3
4
5
6
Press Function/Set, 3, 2. The screen displays: COVERPAGE MSG.
Press
or
to choose position 5 or 6 for your customized comment.
Press Function/Set.
Use the dial pad to enter your customized comment (up to 27 characters).
Press Function/Set. The screen displays:
ACCEPTED
Press 1 if you want to select additional
settings. The display returns to the Setup Send
menu—OR—Press 2 to exit.
OTHER SETTINGS?
1.YES 2.NO
Contrast
If your original is very light or very dark, you might want to set the contrast
accordingly. Use S.LIGHT to send a very light original. Use S.DARK to send a very
dark original.
1
2
3
4
Place the original face down in the ADF.
Press Function/Set, 3, 3.
Press
or
to select AUTO, S.LIGHT or S.DARK and press Function/Set.
Press 2 if you have finished choosing settings, and go to Step 5—OR—Press 1 if you
want to select additional settings. The display returns to the Setup Send menu.
5
Enter a fax number and press Start to send a fax—OR—Press Copy/Help to make
a copy.
Resolution
You must press Resolution (before you send the fax) to select the resolution for the
type of original you’re sending.
STANDARD—suitable for most typed originals.
FINE—good for small print; transmits a little slower than standard resolution.
S. FINE—good for small print or artwork; transmits slower than fine resolution.
PHOTO—use when original has varying shades of gray; slowest transmission time.
If the receiving fax machine does not have the resolution you select, the transmission
will fall back to the next available resolution on receiving machine.
6 - 6
S E T U P S E N D
Advanced Sending Operations
Overseas Mode
If you have difficulty sending a fax overseas, use the Overseas mode.
After you send a fax using this feature, the feature turns itself off.
1
2
3
Place the original face down in the ADF.
Press Function/Set, 3, 5.
5.OVERSEAS MODE
Press
or
to select ON (or OFF) and press
Function/Set.
4
Press 1 if you want to select additional settings. The display returns to the Setup Send
menu—OR—Press 2 if you have finished choosing settings and go to Step 5.
5
6
Enter the fax number you’re calling.
Press Start.
Call Reservation (For FAX-222/333MC Only)
You can send a fax and let the other party know that you want to have a conversation
after the fax transmission is complete. The other fax machine will ring as if it were
receiving a telephone call; if the other party picks up the handset, your fax machine
will ring. Lift the handset to speak.
If you set Call Reservation and Call Back message to ON, your fax machine leaves a
message if the other party does not answer.
1
2
Place the original in the ADF.
Press Function/Set, 3, 6. The screen displays
the current setting for Call Reservation.
CALL RESERVE:OFF
CALL RESERVE:ON
3
4
Press
or
to select ON (or OFF).
If you set Call Reservation to ON, press
Function/Set when the screen displays your
selection. The screen displays the current
setting for Call Back Message.
CALL BACK:OFF?
CALL BACK:ON?
5
6
Press
or
to select ON (or OFF).
Press Function/Set when the screen displays
your selection. The screen displays
ACCEPTED
OTHER SETTINGS?
1.YES 2.NO
7
Press 1 if you want to select additional settings. The display returns to the Setup Send
menu—OR—Press 2 if you are finished choosing settings, and go to Step 8. The
screen prompts you to enter the fax number you want to call.
S E T U P S E N D
6 - 7
8
9
Enter the fax number.
Press Start.
10 If you’ve set Call Reservation to ON, pick up your handset if the fax machine rings.
You cannot use auto redial with Call Reservation. You cannot use Call Reservation
with Delayed Transmission or with Polling. You must register your Station ID to set
Call Back Message to ON.
Print Sample Call Back Message (For FAX-222/333MC Only)
1
2
3
4
Press Function/Set, 3, 6.
Press or to select PRINT SAMPLE?.
Press Function/Set.
Press Start.
Delayed Fax
You can use this function to send a fax up to 24 hours later.
Place the original face down in the ADF.
Press Function/Set, 3, 7.
1
2
3
Enter the time, in 24-hour format, that you want the fax to be sent and press
Function/Set. (For example, enter 19:45 for 7:45 PM)
If you have a FAX-202 or FAX-222, go to Step 5.
4
5
Press 1 to leave the originals waiting in the
ADF—OR—Press 2 to scan the original into
memory.
1.DOC 2.MEMORY
Press 1 to select additional settings.
The display returns to the SETUP SEND menu—OR—Press 2 if you have finished
choosing settings and go to Step 6.
6
7
Enter the fax number.
ENTER FAX NO.
PRESS START KEY
Press Start. The machine will wait to send the
fax at the time you set up.
6 - 8
S E T U P S E N D
Next-Fax Reservation (For FAX-222/333MC Only)
Even if your fax machine is receiving another fax, you can set your machine to send
your fax next. This way, you don’t have to wait for it to finish sending or receiving the
other fax. You can dial this fax call manually, or by using Redial, One Touch, Speed
Dial, or Chain dialing. (When you use One Touch and Speed Dial, only the memory
location—not the name of the person you’re calling—is displayed.)
1
2
3
4
5
Place the originals in the ADF. If necessary, press Resolution to adjust resolution.
Enter the fax number.
Press Start.
Press Function/Set. The screen displays:
NEXT-FAX RESERVD
To cancel the reservation, remove the originals
and press Stop.
You can’t use this feature if there is an original waiting in the ADF (possibly for
Delayed Fax or Polled Transmit).
If you use Next-Fax Reservation , the machine will send an original without storing
it in memory.
Multiple Resolution Transmission
Use this feature to select separate resolution settings for each page of the fax you’re
sending. This could be useful if you’re sending a fax with photos and letters, or some
pages with small print and others with normal print. Resolution settings return to
1
2
3
4
Insert the originals in the feeder, then press Function/Set, 3, 4.
Use
or
to select resolution for page 1, then press Function/Set.
Repeat Step 2 for subsequent pages.
Press Stop when you’re finished. The screen
displays
ACCEPTED
OTHER SETTINGS?
1.YES 2.NO
5
Press 1 if you want to select additional
settings. The display returns to the Setup Send
menu—OR—Press 2 if you are finished
choosing settings, and go to Step 6. The screen
prompts you to enter the fax number you want
to call.
6
7
Enter the fax number you’re calling.
Press Start.
To copy an original using multiple resolutions, press Copy/Help in Step 6.
S E T U P S E N D
6 - 9
Setting Up for Polled Transmit
Polled Transmit is when you set up your fax machine to wait with an original so
another fax machine can retrieve it.
1
2
3
Place the document to be retrieved face down in the ADF.
Press Function/Set, 3, 8.
Press
Function/Set.
If you have a FAX-202 or FAX-222, go to Step
5.
or
to choose ON and press
POLLED TX:OFF?
SELECT <- -> & SET
4
Press 1 to select DOC if you want your
machine to scan the printed document at the
time it is polled—OR—Press 2 to select
MEMORY.
1.DOC 2.MEMORY
5
6
Press 1 if you want to select additional settings. The display returns to the SETUP
SEND menu—OR—Press 2 if you are finished choosing settings and go to step 6.
Press Start.
If you pressed 1 in Step 4, the printed document remains in the ADF until your
machine is polled. However, you can “interrupt” it to send another fax.
Canceling a Scheduled Job
You can cancel tasks you’ve scheduled, such as Delayed Fax or Polling Transmit.
1
2
Press Function/Set, 4. Any waiting
4.CANCEL JOB
jobs appear on the display. If there are no
jobs waiting, the screen displays NO JOB
WAITING.
If you have more than two jobs waiting, press
to cancel and press Function/Set.
—OR—
or
to select the job you want
If you have only one job waiting, go to Step 3.
3
4
Press 1 to cancel—OR—Press 2 to exit without canceling.
Press Stop to exit.
6 - 10
S E T U P S E N D
Interrupting Delayed Fax and Polled Transmit Jobs
You can send a fax or make a copy now, even if you have the fax machine set to send
a fax later, or if you have it set to be polled. However, you cannot use automatic redial
or the function mode.
1
2
Press Function/Set, 5.
Wait 2 seconds, then remove the original that is
waiting in the ADF.
INSERT ORIGINAL
3
Place the original you want to send now in the
ADF.
4
5
6
7
Enter the number for the fax you want to send now.
Press Start.
After the transmission is finished, return the first original to the ADF.
Press Function/Set, 5 to restore the Delayed Fax and/or Polling.
If you have set up a Delayed Fax or Polled Transmit job in memory, you don’t have
to interrupt it to send a fax or make a copy. (For FAX-333MC Only)
If you have set up a Delayed Fax or Polled Transmit job, the machine will send an
original without storing it in memory. (For FAX-333MC Only)
S E T U P S E N D
6 - 11
7
Auto Dial Numbers
7
and Dialing Options
Storing Numbers for Easy Dialing
You can set up your fax machine to do three types of easy dialing:
One Touch, Speed Dial, and Groups for Broadcasting of faxes (For Fax-333MC only).
If you use the Caller ID subscriber service offered by your local phone company (For
Singapore and HongKong only), you can register the number for Anti-Junk Fax/Call
in One Touch and Speed Dial locations.
If you lose electrical power, auto dial numbers in memory will not be lost.
Storing One Touch Dial Numbers/Storing Junk
Fax/Call Numbers
You can store four fax/phone numbers that you can dial by pressing one key (and
Start). You also can store names with these numbers. When you press a One Touch
One Touch keys are not the dial pad keys. They are the four keys (numbers 1–4)
located in the middle of the control panel.
If you want to store a Junk number, you have to set ANTI JUNK to ON in Step 6.
1
2
Press Function/Set, 6, 1.
Press the One Touch key where you want to store a number. The screen displays the
location you selected.
The screen displays the location you selected.
3
4
Enter a number (up to 20 digits) and press
Function/Set.
NAME:
If you want to enter a pause in the dialing sequence (to wait for an “outside line,” for
example), press Redial/Pause as you’re entering digits. Pressing Redial/Pause
enters a 3.5-second pause when the number is dialed, and a dash appears on the
screen.
Use the dial pad to enter the name or company (up to 15 characters) and press
Function/Set. You can use the chart on page 17 to help you enter letters—OR—To
7 - 1
A U T O D I A L N U M B E R S A N D D I A L I N G O P T I O N S
5
Press
or
to select the type of number and press Function/Set.
FAX
TEL
a fax only number
a telephone (voice) number
FAX/TEL both a fax and telephone (voice) number
CHAIN
a number (usually an access code) for chain dialing.
6
7
Press
Function/Set.
or
to select if you set ANTI JUNK to ON (OFF) and press
If you set ANTI-JUNK to ON, the number is registered as the Junk Fax or Call in the
machine. The machine will reject receiving the fax message or telephone call.
If you don’t use the Caller ID subscriber service offered by your local telephone
company, you don’t use the Anti-Junk function.
Press to Step 2 to store another One Touch number—OR—Press Stop to exit.
When you dial an AUTO DIAL number, the screen displays the name you’ve stored,
or, if you haven’t stored a name, the number you’ve stored.
If you must wait for another dial tone at any point in the dialing sequence, store a
pause at that place in the number by pressing Redial/Pause. Each key press adds a
3.5 second pause.
You can use chain dialing to store long dialing sequences. For example, to store 9 1
201 555 1234 987 65 4321, divide the number into two parts. Store the first part as a
Chain type number (this tells the system that the dialing sequence is not complete).
CHAIN—9 1 201 555 1234
The last part of the One Touch number must be stored as any of the other following
three types.
FAX or FAX/TEL or TEL—987 65 4321
Now, when you dial, just press the two keys (one after the other, in order) where
you’ve stored the two parts of the number.
Storing Speed Dial Numbers/Storing Junk Fax/Call
Numbers
You can store Speed Dial numbers, when you dial by pressing only four keys. There
are 8 (FAX-202), 12 (FAX-222) or 50 (FAX-333MC) Speed Dial locations.
If you want to store a Junk number, you have to set ANTI JUNK to ON in Step 6.
1
2
Press Function/Set, 6, 2.
SPEED-DIAL? #
Use the dial pad to enter a two-digit location
and press Function/Set. (01-08) FAX-202,
(01-12) FAX-222, (01-50) FAX-333MC.
#05:
ENTER & SET
A U T O D I A L N U M B E R S A N D D I A L I N G O P T I O N S
7 - 2
3
4
Enter the number (up to 20 digits) and press
Function/Set.
NAME:
Use the dial pad to enter the name or company (up to 15 characters) and press
Function/Set—OR—Press Function/Set to store the number without a name.
5
Press
or
to select the type of number and press Function/Set.
FAX
TEL
a fax only number
a telephone (voice) number
FAX/TEL both a fax and telephone (voice) number
CHAIN
a number (usually an access code) for chain dialing.
6
7
Press
Function/Set.
or
to select if you set ANTI JUNK to ON (or OFF) and press
Return to Step 2 to store another Speed Dial number—OR—Press Stop to exit.
Changing One Touch and Speed Dial Numbers
If you try to store a One Touch or Speed Dial number in a location where a number is
already stored, the screen displays the current name stored there, then prompts you to
either
1. CHANGE—OR—2. EXIT.
1
2
Press 1 to change the number stored, or press 2 to exit without making a change.
Enter a new number.
•
If you want to erase the entire number, press Stop when the cursor is to the left
of the digits. The letters above and to the right of the cursor are deleted.
•
If you want to change a digit, use
or
to position the cursor under the
digit you want to change, then type over it.
3
Follow the directions from Step 3 in Storing One Touch Numbers or Storing Speed
Dial Numbers.
Setting Up Groups for Broadcasting (For FAX-333MC Only)
Groups allow you to send the same fax message to many fax numbers by pressing only one
One Touch key (Broadcasting). First, you’ll need to store each fax number as a One Touch
or Speed Dial number. Then, you can combine them into a Group. Each Group uses up
a One Touch key Finally, you can have up to four small Groups, or you can assign up
.
1
2
Press Function/Set, 6, 3.
SELECT ONE-TOUCH
Select a One Touch key where you wish to store
the number. (For example, press One Touch key 2 to store a Group.)
7 - 3
A U T O D I A L N U M B E R S A N D D I A L I N G O P T I O N S
3
4
Use the dial pad to identify the Group with a
number and press Function/Set. (For
example, press 1 for Group 1.)
SETUP GROUP:GO
ENTER & SET
To include One Touch or Speed Dial numbers
in the Group, enter them as if you were dialing.
For example, for One Touch key 3, press One
G01:*O3#O9_
Touch key 3. For Speed Dial location 09, press Search/Speed Dial, then press 0, 9
on the dial pad. The LCD shows 03, #09.
5
6
Press Function/Set to accept the numbers for
this group.
NAME:
ENTER & SET
Use the dial pad to enter a name for the group
7
Press Stop to exit.
Dialing Options
You can use your fax machine to make voice telephone calls, by dialing manually, or
by using Search, One Touch or Speed Dial memory. You can use the handset or, if you
have FAX-333MC, you can use the Speaker Phone to make and receive calls.
The Speakerphone allows you to operate the phone hands free, or allows more than
one person in the room to participate in a two-way phone conversation.When using
the Speakerphone, make sure to speak clearly and close to the microphone
.
When you dial an auto dial number, the screen displays the name you’ve stored, or, if
you haven’t stored a name, the fax number you’ve stored.
Manual Dialing
Manual dialing is simply pressing all of the digits of the phone number.
Pick up the handset—OR—Press Hook or Speaker Phone.
When you hear a dial tone, dial the number using the dial pad.
1
2
3
If you pressed Hook to dial the call, pick up the handset when the other party answers.
(The speaker works only one way; the other party won’t be able to hear you unless you
pick up the handset.)
On the FAX-333MC, you can switch from handset to Speakerphone by pressing
Speaker Phone, then replacing the handset.You can switch from Speakerphone to
handset by lifting the handset.
4
To hang up, replace the handset—OR—Press Speaker Phone.
A U T O D I A L N U M B E R S A N D D I A L I N G O P T I O N S
7 - 4
One Touch Dialing
1
2
3
When you hear a dial tone, press the One Touch key of the location you want to call.
If you pressed Hook to dial the call, pick up the handset when the other party answers.
(The speaker works only one way; the other party won’t be able to hear you unless you
pickup the handset.)
4
To hang up a voice call, replace the handset—OR—Press Speaker Phone.
If you try to use a One Touch location with no number stored in it, you hear a warning
sound, and screen displays NOT REGISTERED. The display returns to normal after
2 seconds.
If you are sending a fax, press Start after pressing the One Touch key. If you picked
up the handset, press Start when the receiving fax machine answers with fax tones.
Speed Dialing
1
2
3
When you hear a dial tone, press Search/Speed Dial, press #, then press the two-
digit Speed Dial number.
If you pressed Hook to dial the call, pick up the handset when the other party answers.
(The speaker works only one way; the other party won’t be able to hear you unless you
pickup the handset.)
4
To hang up a voice call, replace the handset—OR—Press Speaker Phone.
If you are sending a fax, press Start after entering the Speed Dial number. If you
picked up the handset, press Start when the receiving fax machine answers with fax
tones.
7 - 5
A U T O D I A L N U M B E R S A N D D I A L I N G O P T I O N S
Search
You can search for names you have stored in One Touch and Speed Dial memories.
1
2
3
Press Search/Speed Dial, then enter the first letter of the name you’re looking for.
Press
or
to search the memory.
When the screen displays the name you want to call, pick up the handset or press
Hook or Speaker Phone for a voice call.
4
5
Press Start to begin dialing.
If you pressed Hook to dial the call, pick up the handset when the other party answers.
(The speaker works only one way; the other party won’t be able to hear you unless you
pickup the handset.)
6
When the call is over, hang up—OR—Press Speaker Phone to cancel the call.
Redial
If the last number you dialed was busy, press Redial/Pause for easy dialing.
Answering Calls with the Speakerphone
(For FAX-333MC Only)
When the fax machine rings, instead of lifting the handset, press Speaker Phone.
Speak clearly, toward the microphone
. To end the call, press Speaker Phone.
If you have a bad telephone line connection, the other party might hear your voice
echoed during the call. Hang up and try the call again—OR—Pick up the handset.
Broadcasting (For FAX-333MC Only)
Using the numbers you have stored in Groups, One Touch and Speed Dial memory,
you can “broadcast” faxes automatically to a maximum of 54 different locations in a
ONLY.
After the Broadcast is completed, a Broadcast Report will be printed automatically to
let you know the results.
1
2
Place the original face down in the ADF.
Press Function/Set, 3, 9 to select ON or NEXT FAX ONLY and press
Function/Set.
3
4
Enter the One Touch and Speed Dial numbers (one after the other) or a Group Number
you have stored.
Press Start. The fax machine stores the original in memory, then transmits it to all the
numbers you entered.
A U T O D I A L N U M B E R S A N D D I A L I N G O P T I O N S
7 - 6
Press Stop during transmission to cancel the current fax broadcast.
Pause
Press Redial/Pause to insert a pause between numbers. Each key press adds a 3.5
second delay.
Hold
1
2
3
Press Hold to put a call on Hold.
You can put down the handset without disconnecting the call.
Pick up the fax machine handset—OR—Press Speaker Phone to release the call
from Hold. Picking up an extension handset will not release the call from Hold.
Tone/Pulse
If you have pulse dialing service, but need to send tone signals (for telephone banking,
for example), follow the directions below. If you have touch tone service, you do not
need this feature to send tone signals.
1
2
3
Lift the handset.
Press #. Any digits dialed after this send tone signals.
When you hang up, the fax machine returns to pulse dialing service.
7 - 7
A U T O D I A L N U M B E R S A N D D I A L I N G O P T I O N S
8
Telephone Services
8
Custom Features
Your fax machine supports the Distinctive Ring and Caller ID telephone services
offered by some telephone companies.
If you have Call Waiting, Ring Master, Voice Mail, an answering service or an alarm
system or other custom feature on your telephone line, it may create a problem in the
operation of your fax machine. The Distinctive Ring and Caller ID feature may not
be available in certain area.
Distinctive Ring (For Singapore and Hong Kong)
This fax machine feature lets you use the Distinctive Ring subscriber service offered
by some telephone companies, which allows you to have several telephone numbers
on one phone line. Each phone number has its own Distinctive Ring pattern, so you
know which phone number is ringing. This is one way you can have a separate phone
number for your fax machine.
Your fax machine has a Distinctive Ring function, allowing you to dedicate one phone
number just for receiving faxes. You’ll need to set Distinctive Ringing to ON.
You can switch it off temporarily, then turn it back on. When you get a new fax
number, make sure you reset this function.
■ The fax machine will answer only calls to the Distinctive Ringing number.
■ To have your TAD answer only the main number, the fax machine must be in Manual
Mode.
■ In FAX/TEL or FAX ONLY mode, the fax machine will answer all numbers on the
phone line.
■ The first two rings are silent on the fax machine.
T E L E P H O N E S E R V I C E S
8 - 1
Setting the Distinctive Ring
1
If you have Voice Mail from the Telephone Company, you must disconnect it now
(temporarily).
2
3
4
5
6
7
Disconnect the fax machine from any external telephone answering device (TAD).
Set the fax machine to MANUAL mode.
Press Function/Set, 0, 1.
Press
or
to select ON (or OFF).
Press Function/Set.
Press Stop to exit.
Caller ID (For Singapore and Hong Kong)
The Caller ID feature of this fax machine lets you use the Caller ID subscriber service
offered by many local telephone companies. After at least two rings, the screen
displays the telephone number of your caller (or up to 16 characters of the name, if
available). Once you pick up the handset, the Caller ID information disappears from
the screen, but the call information remains stored in the Caller ID memory.
• CALL PICKUP display remains on the screen when no Caller ID information was
transmitted.
• OUT-OF-AREA display means the call originates outside your Caller ID service area.
• PRIVATE CALL display means the caller has intentionally blocked transmission of
information.
Caller ID service varies with different carriers. Call your local telephone company to
determine the kind of service available in your area.
Caller ID Log
Your fax machine stores up to 10 (FAX-202 and FAX-222) or 30 (FAX-333MC) of
the last Caller IDs received into the fax machine’s memory in the Caller ID Log. When
the 11th (FAX-202 and FAX-222) or 31st (FAX-333MC) call comes in, information
about the first call is erased. You can print the report or scroll through Caller ID
information to review those calls made to your fax machine.
8 - 2
T E L E P H O N E S E R V I C E S
Printing the Caller ID Log
Press Hold.
1
2
CALLER ID LOG
PRINTING
To print the Caller ID Log, press Start.
Viewing the Caller ID Log
1
2
3
Press Hold.
CALLER ID LOG
PRESS START KEY
SELECT <- -> & SET
After 2 seconds, press
through the Caller ID Log.
or
to scroll
01)MARY HENDERSON
02)TOM HENDERSON
03)ABC COMPANY
When you want to see more detailed
information for a displayed ID (phone
number and date and time call was received)
press Function/Set.
03)ABC COMPANY
03)9087772837
03)02/01 12:00
DIAL:PRESS START
4
5
To continue viewing the Caller ID Log (Step
2), press
—OR—
or
.
To exit the Caller ID Log, press Stop.
If you have FAX 333MC, you can delete a name from the Caller ID Log, by pressing
Erase in Step 2 or Step 3.
ERASE THIS DATA?
1.YES 2.NO
Press 1 to erase the selected Caller ID (or 2 to return to the Log without erasing).
Returning a Call from the Log
1
2
Press Hold.
CALLER ID LOG
PRESS START KEY
SELECT <- -> & SET
Press
or
to scroll through the Caller
01)MARY HENDERSON
01)9082438436
ID Log and when you see a call you want to
return immediately, press Function/Set.
01)02/01 12:00
DIAL:PRESS START
3
4
To begin dialing, press Start.
Begin speaking when the other party
answers.
This feature may not be available in certain area.
T E L E P H O N E S E R V I C E S
8 - 3
Registering a Caller ID Number
You can set up a caller in the Caller ID Log as a One Touch or Speed Dial number.
1
Press Hold.
CALLER ID LOG
PRESS START KEY
SELECT <- -> & SET
2
3
After 2 seconds, press
through the Log and when you see a caller
you want to register, press Function/Set.
or
to scroll
03)ABC COMPANY
03)9087772837
03)02/01 12:00
DIAL:PRESS START
To register the caller as a One Touch
number, press the One Touch key where you
want the number to be stored.
—OR—
To register the caller as a Speed Dial number,
press Search/Speed Dial and use the dial
pad to press the two-digit location code (01–
08 or 01-12 or 01-50), and press
Function/Set.
NAME:
ENTER & SET
If the LCD shows REGISTERED, the auto dial location already has a number.
4
5
Enter the caller’s name and press Function/Set.
Press
or
to select the type of number and press Function/Set:
FAX
TEL
A fax number
A telephone (voice) number
FAX/TEL
CHAIN
Both a fax and telephone number
A number, usually an access code, for chain dialing
6
7
Press
Function/Set.
or
to select if you set ANTI-JUNK to ON (or OFF) and press
Return to Step 2 to store another auto dial number—OR—Press Stop to exit.
8 - 4
T E L E P H O N E S E R V I C E S
9
Message Center
9
(For FAX-333MC Only)
Message Center Mode
Message Center Mode allows you to store incoming fax and voice messages in a
flexible memory. The memory stores 15 minutes of voice messages, or up to 20 pages
of fax memory. Any voice or fax message can be retrieved remotely. Memory is
shared between fax and voice messages, which are stored on a “first-come, first-
served” basis.
Flexible Memory Settings (Message Storage)
Message Center Mode offers you six flexible memory settings, so you can decide the
kinds of messages you want to receive.
1.FAX:ON VOICE:ON
Both voice and fax messages are stored. You can use
the Fax Forwarding or Paging features and retrieve
voice and fax messages remotely.
2.FAX:ON VOICE:EXT You need an external answering machine connected to
the EXT jack for this setting. Fax messages are stored
in the message center memory, but voice messages are
stored in your external answering machine. Retrieve
messages from the external answering machine. You
cannot use the Paging feature for voice messages with
this setting.
3.FAX:ON VOICE:OFF All memory is used to store fax messages—no voice
messages will be stored.
4.FAX:OFF VOICE:ON All memory is used to store voice messages—no fax
messages will be stored. Incoming faxes will print on
paper. You can use the Paging feature, and retrieve
voice messages remotely.
5.FAX:OFF VOICE:EXT You need an external answering machine connected to
the EXT jack for this setting. Incoming faxes are not
stored in memory, but will print on paper. Voice
messages are stored in the external answering
machine. (External answering machine can not be
connected in some countries.)
6.FAX:OFF VOICE:OFF Incoming faxes are not stored in memory, but will
print on paper. Voice calls are not stored in memory.
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
9 - 1
Setting Up the Message Center
You must set up the Message Center in the following order:
1
2
3
Setting Message Storage
and VOICE settings below.
1
2
Press Function/Set, 8, 1.
FAX:OFF?
SELECT
& SET
& SET
Press
or
to select ON (or OFF)
VOICE:ON?
SELECT
and press Function/Set.
3
4
Press or
Press Stop to exit.
Recording Message Center Outgoing Message
Recording the Message Center Outgoing Message (MSG CTR OGM) is the second
step you need to follow before you can turn on the Message Center. Make sure your
OGM is less than 20 seconds long.
1
2
Press Function/Set, 8, 3.
The screen prompts you to choose an OGM.
MSG CTR OGM?
SELECT
& SET
Press
or
to select MSG CTR OGM? (not F/T OGM) and press
Function/Set.
This is the only setting you can select if you want to turn the Message Center on.
Press or to select RECORD OGM? and press Function/Set.
3
4
Pick up the handset to record a message.
For example: Hello. We are unable to take your call at this time. Please leave a
message after the signal. If you wish to send a fax, please press 5 1, wait for fax
tones, then press the Start button.
5
6
Replace the handset. The Message Center will play your OGM.
Press Stop to exit.
9 - 2
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
Listening to Outgoing Message (OGM)
1
2
Press Function/Set, 8, 3.
Press
or
to select MSG CTR OGM? (or F/T OGM or PAGING OGM) and
press Function/Set.
3
4
Press or to select PLAY OGM? and press Function/Set. Adjust volume by
or
pressing Volume
.
Press Stop to exit.
Erasing Outgoing Message (OGM)
1
2
Press Function/Set, 8, 3.
Press
or
to select MSG CTR OGM? (or F/T OGM or PAGING OGM) and
press Function/Set.
3
4
5
Press or to select ERASE OGM? and press Function/Set.
Press 1 to erase the OGM—OR—Press 2 to exit without erasing.
Press Stop to exit.
Activating Message Center Mode
Press and hold
until it lights and
the screen displays
MC:MSG CTR
When
Message Indicator
The
light flashes when you have new messages or faxes waiting for your review.
The LCD screen displays the total number of voice
and fax messages stored in the Message Center
memory.
VOICE:03 FAX:02
If you press the flashing
Message Center before getting your new
messages, they won’t be lost. The new messages
to turn off the
PRINT FAX?
1.YES 2.NO
will be played automatically and the LCD will ask you to acknowledge the new faxes:
Press 1 to print (and automatically delete) the faxes from memory—OR—Press 2 to
save the faxes in memory until printing is convenient.
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
9 - 3
Playing Voice Messages
Follow the steps below to listen to voice messages.
1
Press Play/Record. Adjust the Volume by pressing
or
.
All messages are played in the order they were recorded. The display shows the
number of the current message, and the total number of messages.
If Caller ID information was received, the fax machine beeps during the message and
displays the Caller ID information for one second (for some countries).
During playback, the screen displays the time and date the message was recorded.
2
3
Press
(RWD) at the end of the message to repeat a message. Press # (FWD) to skip
to the next message. You can press and # repeatedly until you reach the message
you want to play.
Press Stop to exit.
Printing a Fax Message
Once you print a new fax message stored in memory, it is erased from the memory
automatically.
1
2
3
Press Play/Record. After two seconds, the fax machine begins to play voice
messages.
If there are fax messages in memory, the LCD
displays:
PRINT FAX?
1.YES 2.NO
To print the faxes, press 1
—OR—
Press 2 to exit without printing.
Backup Printing Option
When you choose FAX: ON in the Message Center mode, all incoming fax messages
are stored in the available memory for retrieval. To print a backup copy automatically,
turn this option on.
1
2
Press Function/Set, 8, 2.
BACKUP PRINT:ON
SELECT
& SET
Press
or
to display ON (or OFF) and
press Function/Set.
3
Press Stop to exit.
Erasing Messages
If you choose to erase all fax messages, the fax machine will print any previously
unprinted faxes before erasing them from memory. Fax messages cannot be erased
individually.
You can erase voice messages individually, or all at once.
9 - 4
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
To erase voice messages individually
1
2
Press Play/Record. The fax machine sounds a two-second beep and begins message
playback. Each message is preceded by one long beep, and followed by two short
beeps.
To erase a specific message, press Erase
immediately after the two short beeps, or while
ERASE THIS MSG.?
1.YES 2.NO
the message is playing. The screen prompts
Press 1 to erase the message—OR—Press 2 to cancel.
Press Stop to exit.
3
4
To erase messages all at once
1
2
Press Erase.
ERASE ALL VOICE?
Press
or
to select erasing all voice
SELECT <- -> & SET
messages (VOICE), all document messages
(FAX), or all messages—both voice and fax—(MSG) and press Function/Set.
Press 1 to erase—OR—Press 2 to cancel.
3
4
Press Stop to exit.
Setting Maximum Time for Incoming Messages
Your fax machine comes set to receive voice messages up to 30 seconds long. You can
change this setting to any length from 20 seconds to 60 seconds, in 5-second
increments.
1
2
Press Function/Set, 8, 4.
MESSAGE 30 SEC?
Press
or
to select the maximum time
SELECT
& SET
setting for incoming messages and press
Function/Set.
3
Press Stop to exit.
Setting Toll Saver
When you set the toll saver feature, the fax machine answers after four rings if you
don’t have messages, and after two rings if you do have messages. This way, when
you call the fax machine, if it rings three times, you know you have no messages, and
can hang up, to avoid a toll charge.
When Toll Saver is ON, it overrides your Ring Delay setting. Toll Saver must be off
1
2
Press Function/Set, 2, 1.
Press
Function/Set.
Press or
Press Stop to exit.
or
to select the TOLL SAVER (or RING DELAY) and press
3
4
to select ON and press Function/Set.
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
9 - 5
ICM Recording Monitor
This feature lets you turn the speaker volume for voice messages ON or OFF. When
you turn the monitor OFF, you will not hear messages as they come in.
1
2
3
Press Function/Set, 8, 5.
Use
or
to select OFF (or ON) and press Function/Set.
Press Stop to exit.
Recording a Conversation
You can record a telephone conversation by pressing Play/Record during the
conversation. Your recording can be as long as the Incoming Message Maximum
Time. You and the other party will hear a beep every 15 seconds while recording. To
stop recording, press Stop. You cannot record a conversation using Speaker Phone.
Fax Forwarding/Paging
When Paging is set to ON, your fax machine dials the pager number you’ve
programmed, and plays the Paging OGM you have recorded when connected, to
activate your pager and let you know you have a fax or voice message in the Message
Center memory.
When Fax Forwarding is set to ON, your fax machine dials the fax machine phone
number you’ve programmed, and forwards any faxes you’ve received.
You can not use Paging and Fax Forwarding at the same time.
Programming a Fax Forwarding Number
1
2
Press Function/Set, 8, 6.
Press
or
until the LCD displays
FAX FORWARD? and press Function/Set.
3
4
Enter the number of the fax machine where
faxes will be forwarded (up to 20 digits) and
press Function/Set.
FWD#:
ENTER & SET
Press Stop to exit.
You can not use Paging and Fax Forwarding at the same time.
9 - 6
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
Recording the Paging Outgoing Message (OGM)
Before paging can work, you should first record the Paging OGM.
Press Function/Set, 8, 3. The screen prompts
1
MSG CTR OGM?
SELECT & SET
you to choose an OGM.
2
3
Press
Press
or
or
to reach PAGING MSG.? and press Function/Set.
to Select RECORD OGM? and press Function/Set.
Then pick up the handset to record a message.
Replace the handset. Your OGM is played.
Press Stop.
4
5
Programming Paging Number
1
2
Press Function/Set, 8, 6.
Press
or
until the LCD displays PAGING?
and press Function/Set.
PAG#:
ENTER & SET
3
4
Enter your pager phone number (up to 20
digits) and press Function/Set.
Press Stop to exit.
You can not change a Paging number remotely.
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
9 - 7
Remote Retrieval
Using Remote Retrieval Access Code
1
2
Dial your fax number from a touch tone phone.
When your fax machine answers, immediately enter your Remote Retrieval Access
Code.
3
The fax machine signals the kinds of messages received:
1 long beep—Fax message(s)
2 long beeps—Voice message(s)
3 long beeps—Fax and Voice message(s)
No beeps—no messages
4
The fax machine then prompts you with two short beeps to enter a command. If you
wait longer than 30 seconds to enter a command, the MFC hangs up. If you enter an
invalid command, the fax machine beeps three times.
5
6
Press 9 0 to reset the fax machine when you finish.
Hang up.
If your fax machine is set to MANUAL mode, you can access the Message Center by
waiting about 2 minutes, then entering the Remote Access Code within 30 seconds.
Changing Remote Retrieval Access Code
Enter your Remote Retrieval Access Code when the fax machine picks up your call,
so you can access features remotely. The access code is preset to 159 , but you can
change it.
1
2
Press Function/Set, 8, 7.
Enter a three-digit number from 000 to 999 and press Function/Set. The “
cannot be changed.
”
Do not use the same digits that appear in your Fax Receive Code or Telephone
Answer Code.
3
Press Stop to exit.
9 - 8
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
Remote Commands
Follow the commands below to access features remotely. When you call the
fax machine and enter your Remote Retrieval Access Code (159 ), the system will
signal you with two short beeps to enter a remote command.
Remote Commands
Operation Details
91 Playing Voice Messages
After one long beep, the fax machine plays
ICM.
1
2
(go back)
Press 1 while listening to an ICM to repeat it.
If you press 1 before a message, you will hear
the previous message.
(Skip to next)
While playing the ICM, you can skip to the
next message.
9 STOP Playing
Stop playing the ICM.
92 Record Memo
After one long beep, you can record a memo.
To stop recording, press 9.
93 Erase all ICM
If you hear one long beep, the erase is accepted.
If you hear three short beeps, you cannot erase
because all voice messages have not been
played, or there is no voice message to erase.
*This code erases all recorded messages, not
one at a time.
94 Play and Record OGM in
memory
1 Play
1 MSG CTR OGM
2 F/T OGM
The fax machine plays the selected OGM. You
can stop playing OGMs by pressing 9.
3 PAGING MSG.
2 Record 1 MSG CTR OGM
2 F/T OGM
After one long beep, you can record the
selected OGM. You will hear the message
played once. You can stop recording the
message by pressing 9.
3 PAGING MSG.
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
9 - 9
Remote Commands
Operation Details
95 Changing Fax Forwarding/
Paging Setting
If you hear one long beep, the change is
accepted. If you hear three short beeps, you
cannot change it because the conditions have
not been met (Example: registering paging
number). You can register your fax forwarding
the fax machine will change automatically to
FAXFWD:ON mode. Then retrieve a Memory
to make sure that the Fax Forwarding number
you registered is correct in the List.
1 OFF
2 Fax Forwarding
3 Paging
4 FAX FWD NO.
96 Retrieve a fax
1 Memory Status List
2 Retrieve all faxes
Enter the number of a remote fax machine to
3 Erase fax in the memory
If you hear one long beep, you can erase the fax
message from the memory.
97 Check the receiving status
You can check whether your fax machine has
received any FAX or VOICE messages. If yes,
you will hear one long beep. If no, you will
hear three short beeps.
1 FAX
2 VOICE
98 Change Answer Mode
1 MSG CTR
If you hear one long beep, you can change the
answer mode. If you hear three short beeps,
you cannot change it. (Example: There is no
MSG CTR OGM when you want to change to
MSG CTR mode.)
2 FAX/TEL
3 FAX
90 Exit
After a long beep, you can exit remote control.
9 - 10
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
Retrieving Memory Status List
You can retrieve the Memory Status List from a remote fax machine to see if you have
any fax messages.
1
2
Dial your fax number.
When you hear the beep, immediately enter your Remote Retrieval Access Code
(1 5 9 ).
3
4
When you hear two short beeps, use the dial pad to press 9 6 1.
Using the dial pad, enter the number of the remote fax machine (up to 20 digits) where
you want the Memory Status List forwarded, and then press # #.
You can not use or # as dial numbers. However, if you want to store a pause, press
#.
5
After you hear your fax machine beep, hang up and wait.
Your fax machine calls the remote fax machine. The remote fax machine prints the
Memory Status List.
Retrieving Fax Messages
1
2
Dial your fax from a remote telephone or fax machine using touch tone.
When you hear the beep, immediately enter your Remote Retrieval Access Code
(1 5 9 ).
3
4
As soon as you hear two short beeps, use the dial pad to press 9 6 2.
Using the dial pad, enter the number of the remote fax machine (up to 20 digits) where
you want your fax messages forwarded, and then press # #.
You can not use or # as dial numbers. However, if you want to store a pause, press
#.
5
After you hear your fax machine beep, hang up and wait.
Your fax machine calls the remote fax machine. The remote fax machine prints your
fax messages.
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
9 - 11
Changing Fax Forwarding Number
You can change the default setting of your fax forwarding number from a remote fax
machine.
1
2
Dial your fax number.
When you hear the beep, immediately enter your Remote Retrieval Access Code
(1 5 9 ).
3
4
When you hear two short beeps, use the dial pad to press 9 5 4.
Enter the new number of the remote fax machine where you want your fax messages
forwarded, then press # #.
You can not use
or # as dial numbers. However, if you want to store a pause, press
#.
5
6
7
To retrieve the Memory Status List, when you hear two short beeps, use the dial pad
to press 9 6 1.
Use the dial pad to enter the number of the remote fax machine (up to 20 digits), then
press # #.
After you hear your fax machine beep, hang up and wait.
Your fax machine calls the remote fax machine. The remote fax machine prints the
Memory Status List showing the new forwarding number.
8
Check the forwarding number.
If the forwarding number is not correct, return to Step 1 to reset it.
9 - 12
M E S S A G E C E N T E R ( F O R F A X - 3 3 3 M C O N L Y )
10
Making Copies
10
Copy Functions
To make a single copy that is not reduced, enlarged or sorted, you only have to press
one key. The default resolution for a single copy is Super Fine. Set the resolution to
PHOTO for photographs. Remember, your machine cannot scan anything closer than
one-eighth inch from the edge of the paper.
Making a Single Copy
1
2
Place the original face down in the ADF.
Press Copy/Help twice.
(If you have FAX-333MC, press Copy/Help twice.)
To cancel, press Stop.
Do NOT pull on the paper while copying is in progress.
Copy Options: Single or Multiple Copies, Sort/Stack
(For Fax-333MC Only)
You can choose additional copy options. First, you can select the number of copies.
Next, you can choose whether multiple copies will be STACKED (all copies of page 1,
then all copies of page 2, etc.) or SORTED (collated).
1
2
Place the original face down in the ADF.
Press Copy/Help.
NO.OF COPIES:01
THEN COPY OR SET
3
Enter the number of copies you want (1-99).
For example, press 9 for nine copies.
NO.OF COPIES:09
To start copying now, press Copy/Help.
STACK
P.01 FNE
If you would like to set SORT, press
Function/Set and then press Copy/Help.
MULTI COPY:STACK
THEN COPY OR SET
4
Press
or
to select SORT or STACK.
For example, select SORT and Copy/Help.
MULTI COPY:SORT
SORT
P.01 FNE
M A K I N G C O P I E S
10 - 1
If you are making multiple copies and get a OUT OF MEMORY message while you
are scanning the first page, press Stop to cancel the job. Then make a single copy. If
you selected SORT and the OUT OF MEMORY message appears while scanning
subsequent pages, you can press Copy/Help to copy the portion that is in memory,
or press Stop to cancel. To restart the copy job using less memory, press Copy/Help
for stacked copies.
10 - 2
M A K I N G C O P I E S
11
Printing Reports
11
Fax machine Settings and Activity
You can print the following lists and reports:
Choose to print a Transmission Verification
Report after each fax you send.
1.XMIT REPORT
2.ACT.REPORT
Activity Report lists information about the last 15
(FAX-202/222) or 30 (FAX-333MC) incoming
and outgoing faxes. TX means Transmit; RX
means Receive.
Lists names and numbers stored in One Touch and
Speed Dial memory, in numerical order.
3.AUTO DIAL
AUTO DIAL LIST (above), alphabetically.
4.TEL.INDEX
Lists settings for INITIAL SETUP, SETUP
RECEIVE, SETUP SEND, PRINT REPORTS,
TEL SERVICE, and SETUP MSG CTR
(for FAX-333MC only).
5.USER SETTINGS
Lists summary information and amount of
memory in use.
6.MEMORY STATUS
(For FAX-333MC Only)
To Print a Report
1
2
Press Function/Set, 7.
Enter the number of the report you want to print. For example, press 4 to print the
TEL.INDEX.
For the Activity Report, also press
or
to select PRINT REPORT?.
3
4
Press Start.
Press Stop to exit.
P R I N T I N G R E P O R T S
11 - 1
Transmission Verification (Xmit) Report
You can use the Xmit Report as proof that you sent a fax. This report lists the name
or fax number of the receiving party, the time and date of transmission, and whether
the transmission was successful.
When the feature is OFF, the report is printed automatically only if there’s an error
during transmission. If the report indicates NG, send the original again. If the report
indicates you should check the readability of certain pages, resend those pages.
When the feature is ON, the report is printed with every fax you send.
1
2
3
Press Function/Set, 7, 1.
Press
or
to select ON (or OFF) and press Function/Set.
Press Stop to exit.
Activity Report Interval
You can set the fax machine to print activity reports at specific intervals (6, 12, 24
hours, 2, 4 or 7 days). If you set the interval to OFF, you can print the report by
following the steps in the previous section.
1
2
Press Function/Set, 7, 2.
Press
or
to display:
INTERVAL?
and press Function/Set.
3
4
5
Press or to choose your setting and press Function/Set. If you choose 7
days, the screen prompts you to choose a day at which to begin the 7-day countdown.
Enter the time, in 24-hour format, that printing will begin and press Function/Set.
(For example, enter 19:45 for 7:45 PM)
Press Stop to exit.
11 - 2
P R I N T I N G R E P O R T S
12
Important Information
12
Important Safety Instructions
1
2
3
Read all of these instructions and save them for future use.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol
cleaners. Use a damp cloth for cleaning.
4
5
Do not use this product near water.
Do not place this product on an unstable cart, stand, or table. The product may drop,
causing serious damage to the product.
6
Slots and openings in the cabinet and the back or bottom of the machine are provided
for ventilation; to ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface.
This product should never be placed near or on a radiator or heater. This product
should never be placed in a built-in installation unless proper ventilation is provided.
7
8
This product should be operated from the type of power source indicated on the label.
If you are not sure of the type of power available, consult with your dealer or local
power company.
This product is equipped with a 2-wire grounding type plug or a 3-wire grounding type
plug (for Singapore, Malaysia, Hong Kong and India). This plug will only fit into a
grounding-type power outlet. This is a safety feature. If you are unable to insert the
plug into the outlet, contact your electrician to replace your obsolete outlet. Do not
defeat the purpose of the grounding-type plug.
9
Do not allow anything to rest on the power cord. Do not place this product where
people can walk on the cord.
10 If an extension cord is used with this product, make sure that the total ampere ratings
on the products plugged into the extension cord do not exceed ampere rating of the
extension cord ampere rating.
11 Do not place anything in front of the fax machine that will block the exit- path of sent
documents, originals and received faxes.
12 Do not touch an original during printing.
13 Never push objects of any kind into this product through cabinet slots, because they
may touch dangerous voltage points or short out parts resulting in a risk of fire or
electric shock. Never spill liquid of any kind on the product.
I M P O R T A N T I N F O R M A T I O N
12 - 1
14 Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points and/or other risks, and may void your
warranty. Please refer all servicing to our Authorized Service Personal. You may
contact the Brother Dealer for Service.
15 Unplug this product from the wall outlet and refer servicing to Authorized Service
Personal under the following conditions:
A
B
C
D
If the power cord is damaged or frayed.
If the product has been spilled by liguid.
If the product has been exposed to rain or water.
If the product does not operate normally when the operating instructions are
followed. Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product
to normal operation.
E
F
If the product has been dropped or the cabinet has been damaged.
If the product exhibits a distinct change in performance, indicating a need for
service.
16 To protect your product against power surges, we recommend the use of a power
protection device (Surge Protector).
WARNING
For protection against the risk of electrical shock, always disconnect all cables from
the wall outlet before servicing, modifying or installing the equipment.
This equipment may not be used on coin service lines provided by the telephone
company or connected to party lines.
Brother cannot accept any financial or other responsibilities that may be the result of
your use of this information, including direct, special or consequential damages.
There are no warranties extended or granted by this document.
12 - 2
I M P O R T A N T I N F O R M A T I O N
13
Troubleshooting and
13
Maintenance
Troubleshooting
Error Messages
You may occasionally encounter a difficulty with your fax machine or telephone line.
If this happens, your fax machine often identifies the problem and displays an error
message. The list below explains the most common error messages.
A poor quality phone line resulted in a
communications error. Try the call again.
COMM.ERROR XX XX
You have requested a polling call from another
party, but the other fax machine is not in Poll
Waiting mode.
CONNECTION FAIL
The cover is not completely closed.
COVER OPEN
PLS CLOSE COVER
The fax paper is jammed in the cutter.
CUTTER JAM
PLS OPEN COVER
CUTTER JAM
REMOVE PAPER
1
2
3
4
Unplug the power cord.
Open the cover.
Pull the blue release lever on the print head unit and raise it.
Gently turn the paper roll toward the front of the machine to roll out the jammed paper.
Recording paper
5
Use scissors to cut off the wrinkled portion of the paper.
T R O U B L E S H O O T I N G A N D M A I N T E N A N C E
13 - 1
6
7
Plug in the power cord.
Load the fax paper again, and push the blue release lever down. Close the cover.
The other party has disconnected during a call or
fax. Try calling the other party.
DISCONNECTED
The documents were not inserted or fed properly,
or were too long or too short.
CHECK DOCUMENT
REMOVE DOCUMENT
CHECK DOCUMENT
PRESS STOP KEY
1
2
Open the cover.
Pull the documents toward the front of the fax machine, in the same direction they
were feeding.
3
Close the cover.
Front cover
Contact your Brother Dealer for service,
CALL BROTHER CS
MACHINE ERROR XX
The number you called does not answer or is
NO RESPONSE/BUSY
busy. You may also have reached a number not
connected to a fax. Check the number and call
again.
You’ve tried accessing a One Touch or Speed
NOT REGISTERED
Dial location with no number assigned to it. See
chapter 7 for information about storing One
Touch and Speed Dial numbers.
The paper roll is empty; follow the instructions in
Installation to replace the paper roll.
PAPER ROLL EMPTY
RELOAD PAPER
13 - 2
T R O U B L E S H O O T I N G A N D M A I N T E N A N C E
The recording head has overheated. Unplug the
machine and wait 30 minutes for it to cool.
COOLING DOWN
WAIT FOR A WHILE
Try cleaning the white bar and the glass under the
bar with isopropyl alcohol.
SCANNER ERROR
If you still get a scanner error, contact Brother
Dealer for service.
Front cover
The memory capacity has been exceeded while
Erase the incoming voice messages or fax
messages stored in memory in order to make
OUT OF MEMORY
PRINT:PRESS COPY
OUT OF MEMORY
QUIT:PRESS STOP
The memory capacity has been exceeded while
OUT OF MEMORY
SEND:PRESS START
OUT OF MEMORY
QUIT:PRESS STOP
messages stored in memory in order to make
Recording Paper Jam
If something was placed in front of your fax machine, during printing the recording
paper may become jammed. To roll out the jammed paper, follow the instructions for
T R O U B L E S H O O T I N G A N D M A I N T E N A N C E
13 - 3
If You Are Having Difficulty with Your Fax Machine
If you think there is a problem with your fax machine, make a copy first. If the copy
looks good, the problem is probably not your fax machine. Check the difficulties
below and follow the troubleshooting tips.
Printing or Receiving Faxes
Condensed Print and Horizontal Streaks;
Top and Bottom of Sentences Cut Off
If your copy looks good, you probably had a bad connection, with static or
interference on the phone line.
Enabling/Disabling Anti-Curl Check Sheet (ACS)
(For Some Countries)
Although the factory setting of Anti-Curl Check Sheet feature is OFF, you can
check the status of your fax machine’s Anti-Curl (ACS) feature by printing an
Anti-Curl Check Sheet.
Press One touch key 1 and 4 at the same time to print an ACS Check Sheet.
Press One touch key 1 and 4 at the same time to discontinue printing ACS
Check Sheet.
Vertical Black Lines When Receiving
The sender’s scanner may be dirty. Ask the sender to make a copy to see if the
problem is with the sending machine. Try receiving from another fax machine.
Phone Line or Connections
Fax Machine Does Not Answer When Called
Make sure the fax machine is in the correct receiving mode for your setup
(either FAX, FAX/TEL or MSG CTR). Check for dial tone. If possible, call
your fax machine to hear it answer. If there is still no answer, check the
telephone line cord connection. Connect a standard telephone handset to the fax
machine telephone jack. If there is no ringing when you call your fax machine,
call your Telephone Company to check the line.
No Dial Tone on the Handset
Press Hook or Speaker Phone—OR—Lift the handset. If you hear no dial
tone, check telephone line cord connections at the fax machine and wall jack.
Check that the handset is connected to the fax machine’s handset jack. Test the
wall jack with another single line telephone. If no dial tone on the wall outlet,
call your Telephone Company.
13 - 4
T R O U B L E S H O O T I N G A N D M A I N T E N A N C E
Sending Faxes
Poor Transmitting Quality
Try cleaning the white pressure bar of the scanner and the glass under the bar
Dialing Does Not Work
Check for a dial tone.
Check all line cord connections, and make sure the curled handset cord is not in
the EXT jack.
Check power cord connection.
Send a manual fax by pressing Hook or Speaker Phone —OR— Lifting the
handset, and dialing the number. Wait to hear fax receiving tones before
pressing Start.
Vertical Black Lines When Sending
Use your fax machine to make a copy. If the copy shows the same problem, the
scanner area is dirty. Lift the front cover and check the document path. Clean
the scanner’s white pressure bar and the glass under the bar using isopropyl
Handling Incoming Calls
F/T pseudo-ring in FAX/TEL Mode
The fax machine knows the incoming call is not a fax so it is signaling you to
answer the telephone call. Pick up the fax machine handset or answer from an
extension phone and press your fax machine’s Telephone Answer Code (default
Transferring a Call to the Fax Machine
If you have answered the fax machine handset, press Start, and hang up
immediately.
If you answered at an extension phone, press your three-digit Fax Receive Code
(the factory setting is 51). When your fax machine answers, hang up.
Fax Machine “Hears” Voice as CNG Tone
If your fax machine is set to Easy Receive ON, and it answers voice calls by
trying to receive a fax, try turning Easy Receive to OFF.
T R O U B L E S H O O T I N G A N D M A I N T E N A N C E
13 - 5
Transmission Verification Report Prints “Result: NG”
There is probably temporary noise or static on the phone line. Try sending the
fax again. If the problem continues, call the Telephone Company to check your
phone line.
Custom Features on a Single Line
If you have Call Waiting, Caller ID, Ring Master, Voice Mail, an answering
machine, alarm system or any other custom feature on a single phone line with
your fax machine, it may create a problem with sending or receiving fax data
and telephone calls.
13 - 6
T R O U B L E S H O O T I N G A N D M A I N T E N A N C E
14
Multi-Function Link® (option)
14
®
®
You can purchase the optional Multi-Function Link package. Multi-Function Link
turns your fax machine into a multifunction center, by enabling you to use your fax
machine as a printer and a scanner and to use it to fax messages from Windows
applications in your computer.
®
Multi-Function Link is available at most Brother retailers. If you cannot find it, you
®
can order Multi-Function Link directly from Brother.
®
Installation instructions will be included with the Multi-Function Link package.
However, it is important that you hook up your fax machine to your computer before
you install the software.
®
M
U
L
T
I
-
F
U
N
C
T
I
O
N
L
I
N
K
(
O
P
T
I
O
N
)
14 - 1
Specifications
Type
Desktop facsimile transceiver
Compatibility
Coding System
Modem Speed
ITU-T Group 3
Modified Huffman (MH)
9600/7200/4800/2400;
Automatic Fallback (FAX-202, FAX-222)
14400/12000/9600/7200/4800/2400;
Automatic Fallback (FAX-333MC)
Original Input Width
5.8 inches to 8.5 inches (148 mm to 216 mm)
Scanning/Printing Width 8.2 inches (208 mm)
Paper Roll Size:Width
Length
8.5 inches (216 mm)
164 feet (50 m) with standard thermal paper 98 feet (30 m)
with Therma PLUS paper
Diameter
Limited to 2.76 inches (70 mm)
Line Thermal
Printer type
Gray Scale
Display
64 levels (Dithered)
LCD, 16 characters
Polling Types
Contrast Control
Resolution
Standard, Sequential (For FAX-333MC Only), Delayed
Automatic/Super Light/Super Dark (manual setting)
• Horizontal 203 dot/inch (8 dot/mm)
• Vertical Standard—98 line/inch (3.85 line/mm)
Fine, Photo—196 line/inch (7.7 line/mm)
Superfine, Photo (copy)—392 line/inch (15.4
line/mm)
Memory Capacity
One Touch Dial
Speed Dial
512 KB (up to 20 pages*) (For FAX-333MC Only)
4
8 stations (FAX-202)
12 stations (FAX-222)
50 stations (FAX-333MC)
Automatic Redial
10 times at 3 minute intervals (Singapore, Malaysia,
Indonesia, Turkey, Hong Kong, India)
3 times at 5 minute intervals (in some countries)
Speaker Type
Auto Answer
Monitor (FAX-202, FAX-222)
Full Duplex, Digital (FAX-333MC)
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 rings (Singapore, Malaysia,
Hong Kong, India)
0, 1, 2, 3 or 4 rings (in some countries)
* “Pages” refers to the ITU-T #1 chart (in Out of Paper Reception in ECM mode).
Specifications are subject to change without prior notice.
S - 1
S P E C I F I C A T I O N S
Communication Source
Operating Environment
Power Source
Public switched telephone network
41 - 95° F (5° - 35°C)
220~240V AC 50/60Hz
Power Consumption
Dimensions
Standby: under 5 watts — Peak: under 110 watts
11.8 x 9.4 x 5.4 (inches)/ 299 x 240 x 137 (mm)
6.4 lb / 2.9 kg
Weight
S P E C I F I C A T I O N S
S - 2
Glossary
Activity Report Lists information about the last 15 (FAX-202, FAX-222) or
30 (FAX-333MC) incoming and outgoing faxes. TX means Transmit. RX means Receive.
ADF (Automatic original Feed) Refers to the number of pages that can be placed in the original
feeder and fed one at a time automatically.
Auto Dial List A listing of names and numbers stored in One Touch and Speed Dial memory, in
numerical order.
automatic fax transmission Sending a fax without picking up the handset or pressing Hook or
Speaker Phone.
beeper The sound the keys make when they are pressed, an error occurs or an original has been
received or transmitted.
Broadcasting The ability to send the same fax message to more than one location.
Call Back Message Allows you to send a fax and then leave a message for the other party to call
you back.
Call Reservation Allows you send a fax and then at the end of transmission, you can talk with
the other party.
Cancel Job Cancels a programmed job, like Delayed Fax or Polling.
CNG tones The special tones (beeps) sent by fax machines during automatic transmission to tell
the receiving machine that they are a from fax machine.
communication error (or Comm. Error) An error during fax sending or receiving, usually
caused by line noise or static.
Contrast Setting to compensate for dark or light originals, by lightening dark originals or
darkening light originals.
Cover Page Prints a page at the other party’s machine, that contains the sender and recipient’s
name and fax number, number of pages and comment. You can generate an electronic cover
page at the other end with pre-programmed information from memory or you can print a
sample cover page to fax with your original.
Delayed Fax Sends your fax at a later time that day.
Distinctive Ring A service purchased from the Telephone Company that provides another phone
number on an existing phone line. The Brother fax machine uses the new number to simulate
a dedicated fax line.
ECM (Error Correction Mode) Detects errors during fax transmission and resends the page(s)
of the original that had an error.
F/T Ring Time The length of time the fax machine rings (when the answer mode setting is
FAX/TEL) to notify you to pick up a voice call that it answered.
Fax Forwarding Sends a fax received in memory to another preprogrammed fax number.
fax tones The signals sent by sending and receiving fax machines while communicating
information.
Fine Mode Resolution is 196 x 203 dpi. It is used for small print and graphs.
G - 1
G L O S S A R Y
gray scale The shades of gray available for copying and faxing photographs.
group number A combination of One Touch and/or Speed Dial numbers that are stored on a One
Touch key for Broadcasting.
Interrupt Temporarily puts a waiting job on hold while you perform another operation.
interval The preprogrammed time period between automatically printed Activity Reports. You
can print Activity Reports on demand without interrupting this cycle.
LCD (liquid crystal display) The display screen on the fax machine that shows interactive
messages during On-Screen Programming and defaults to the date and time when the machine
is idle.
manual fax When you press Hook or Speakerphone—OR—lift the handset so you can hear
the receiving fax machine answer before you press Start to begin transmission.
Memory Status List Shows how much memory is being used, how much is left, and the type of
messages in memory.
Memory Transmission You can set your machine to scan originals before dialing, so you do not
have to leave them at the fax machine.
memory usage Instructs the fax machine how to allocate the memory.
Next Fax Reservation Accepts the next original in the original feeder for transmission while the
fax machine is still receiving.
OGM (Out-Going Message) The message callers hear when you call your external answering
machine.
One Touch Keys on the fax machine control panel where you can store numbers for easy dialing.
You must use a separate key for each number.
Out of Paper Reception Receives faxes into the fax machine’s memory when the machine is out
of paper.
Overseas Mode Makes temporary changes to the fax tones to accommodate noise and static on
overseas phone lines.
Paging Feature enables your fax unit to call your pager when a fax and/or a voice message is
received into its memory.
Pause Allows you to place a 3.5 second delay in the dialing sequence stored on One Touch and
Speed Dial numbers.
Photo Mode A resolution setting that uses varying shades of gray for the best representation of
photographs.
polling The process of a fax machine calling another fax machine to retrieve waiting fax
messages.
Pulse A form of dialing on a telephone line.
remote access The ability to access your fax machine remotely from a touch tone phone.
remote activation allows you to transfer a fax call, answered at an extension phone, to the fax
machine.
remote access code The four-digit code that allows you to call and access your fax machine from
a remote location.
resolution The number of vertical and horizontal lines per inch. See: Standard, Super Fine and
Photo.
G L O S S A R Y
G - 2
Rotary A form of dialing on a telephone line.
scanning The process of sending an electronic image of a paper document into your computer.
Search An electronic, alphabetical listing of stored One Touch, Speed Dial and Group numbers.
Speed dial A preprogrammed number for easy dialing. You must press the Search/Speed Dial
key, press #, and then the two digit code to start the dialing process.
Standard resolution 98 x 203 dpi. It is used for regular size text and quickest transmission.
Station ID The stored information that appears on the top of faxed pages. It includes the sender’s
name and fax number.
super fine resolution 392 x 203 dpi. Best for very small print and line art.
Tone A form of dialing on the telephone line used for Touch Tone telephones.
transmission The process of sending originals over the phone lines from your fax machine to the
receiving fax machine.
User Setting List A printed report that shows the current settings of your fax machine.
Xmit Report (Transmission Verification Report) A listing of each transmission, showing
caller ID, date, time, and number of pages.
G - 3
G L O S S A R Y
I
R
M
S
O
T
P
TRANSMISSION VERIFICATION
I - 2
I N D E X
I - 4
I N D E X
Using Remote Retrieval Access Code (For FAX-333MC Only)
If you plan to retrieve voice or fax messages while away from your fax machine,
carrying the Remote Retrieval Access Card printed below will serve as a convenient
reminder of the retrieval procedures. Simply cut out the card and fold it to fit in your
wallet or organizer. Keeping it handy will help you derive the full benefit of your fax
machine’s forwarding, paging and remote retrieval features.
R E M O T E R E T R I E V A L A C C E S S C A R D
R - 1
R - 2
R E M O T E R E T R I E V A L A C C E S S C A R D
®
AS.GU
LE51690401
Printed in Malaysia
|
