(Original instructions)
ENGLISH
G
H
8
9
1
I
J
Intended use
Your BLACK+DECKERTM BEHTS301, BEHTS401,
BEHTS451, BEHTS501 hedgetrimmers have been designed
for trimming hedges, shrubs and brambles. These tools are
intended for consumer use only.
Safety instructions
General power tool safety warnings
Warning! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions listed below may result in electric
shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains
operated (corded) power tool or battery operated (cordless)
power tool.
K
3
(Original instructions)
ENGLISH
1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases
or dust. Power tools create sparks which may ignite the
dust or fumes.
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
d. Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at
all times. This enables better control of the power tool in
unexpected situations.
f. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long hair
can be caught in moving parts.
2. Electrical safety
g. If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection can
reduce dust-related hazards.
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs
with earthed (grounded) power tools. Unmodified plugs
and matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c. Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
d. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool. Keep
cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of
electric shock.
e. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
f. If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
4. Power tool use and care
a. Do not force the power tool. Use the correct power
tool for your application. The correct power tool will do
the job better and safer at the rate for which it was
designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with
the switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any
adjustments, changing accessories, or storing power
tools. Such preventive safety measures reduce the risk of
starting the power tool accidentally.
d. Store idle power tools out of the reach of children and
do not allow persons unfamiliar with the power tool or
these instructions to operate the power tool. Power
tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and any
other condition that may affect the power tools
operation. If damaged, have the power tool repaired
before use. Many accidents are caused by poorly
maintained power tools.
3. Personal safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a
power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention
while operating power tools may result in serious personal
injury.
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask,
non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal
injuries.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g. Use the power tool, accessories and tool bits etc. in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source
and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or
energising power tools that have the switch on invites
accidents.
5. Service
a. Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
4
(Original instructions)
ENGLISH
Never attempt to use an incomplete tool or a tool with
unauthorised modifications.
u Never allow children to use the tool.
u Be aware of falling debris when cutting the higher sides of
a hedge.
Additional power tool safety warnings
Warning! Additional safety warnings for hedge
trimmers
@
u Keep all parts of the body away from the cutter blade.
Do not remove cut material or hold material to be cut
when blades are moving. Make sure the switch is off
when clearing jammed material. A moment of inattention
while operating the tool can result in serious personal
injury.
u Always hold the tool with both hands and by the handles
provided.
Residual risks
Additional residual risks may arise when using the tool which
may not be included in the enclosed safety warnings. These
risks can arise from misuse, prolonged use etc.
Even with the application of the relevant safety regulations
and the implementation of safety devices, certain residual
risks can not be avoided. These include:
u Injuries caused by touching any rotating/moving parts.
u Injuries caused when changing any parts, blades or ac-
cessories.
u Carry the hedge trimmer by the handle with the cutter
blade stopped. When transporting or storing the
hedge trimmer always fit the cutting device cover.
Proper handling of the hedge trimmer will reduce possible
personal injury from the cutter blades.
u Hold the power tool by insulated gripping surfaces
only, because the cutter blade may contact hidden
wiring or its own cord. Cutter blades contacting a "live"
wire may make exposed metal parts of the power tool
"live" and could give the operator an electric shock.
u Keep cable away from cutting area. During operation
the cable can be hidden in shrubs and can be accidentally
cut the blades.
u The intended use is described in this instruction manual.
The use of any accessory or attachment or performance
of any operation with this tool other than those recom-
mended in this instruction manual can present a risk of
personal injury and/or damage to property.
u If you have not used a hedge trimmer before, preferably
seek practical instruction by an experienced user in addi-
tion to studying this manual.
u Never touch the blades while the tool is running.
u Never attempt to force the blades to come to a standstill.
u Do not put the tool down until the blades have come to a
complete standstill.
u Regularly check the blades for damage and wear. Do not
use the tool when the blades are damaged.
u Take care to avoid hard objects (e.g. metal wire, railings)
when trimming. Should you accidentally hit any such
object, immediately switch the tool off and check for any
damage.
u Should the tool start to vibrate abnormally, immediately
switch it off and disconnect it from the mains suply then
check for any damage.
u If the tool stalls, immediately switch it off. Disconnect it
from the mains supply before attempting to remove any
obstructions.
u Injuries caused by prolonged use of a tool. When using
any tool for prolonged periods ensure you take regular
breaks.
u Impairment of hearing.
u Health hazards caused by breathing dust developed when
using your tool (example:- working with wood, especially
oak, beech and MDF.)
Vibration
The declared vibration emission values stated in the technical
data and the declaration of conformity have been measured
in accordance with a standard test method provided by
EN 60745 and may be used for comparing one tool with
another. The declared vibration emission value may also be
used in a preliminary assessment of exposure.
Warning! The vibration emission value during actual use of
the power tool can differ from the declared value depending
on the ways in which the tool is used. The vibration level may
increase above the level stated.
When assessing vibration exposure to determine safety
measures required by 2002/44/EC to protect persons regularly
using power tools in employment, an estimation of vibration
exposure should consider, the actual conditions of use and the
way the tool is used, including taking account of all parts of the
operating cycle such as the times when the tool is switched off
and when it is running idle in addition to the trigger time.
Labels on tool
The following pictograms are shown on the tool along with the
date code:
u After use, place the blade sheath supplied over the
blades. Store the tool, making sure that the blade is not
exposed.
Warning! To reduce the risk of injury, the user
must read the instruction manual.
u Always ensure that all guards are fitted when using the
tool.
5
(Original instructions)
ENGLISH
u Remove guard retaining screw 10 with a Phillips
screwdriver (not supplied).
u Position the guard in place as shown in Fig. A. Ensuring
the guard slots into the grooves on the unit.
Wear safety glasses or goggles when operating
this tool.
Wear ear protection when operating this tool.
u Insert the guard retaining screw 10 into the opening on the
side of the guard and tighten securely as shown in Fig. B.
Warning! Only use with handle and guard properly assembled
to hedge trimmer. The use of the hedge trimmer without
the proper guard or handle provided may result in serious
personal injury.
Immediately disconnect the cable from the mains
if it is damaged or cut.
Do not expose the tool to rain or high humidity.
Attaching extension cord to trimmer (fig. C)
A cord retainer (7) is incorporated into the rear of the switch
handle (6).
u Near the end of the extension cord, fold the extension
cord to create a loop.
Directive 2000/14/EC guaranteed sound power.
Electrical safety
u Feed the loop into the cord retainer housing 11 as shown
in Fig. C.
This tool is double insulated; therefore no earth
wire is required. Always check that the power
supply corresponds to the voltage on the rating
plate.
u Hook the loop onto the cord retainer 7 so it rests in the
cord retainer.
u Plug the extensvion cord into the unit.
u If the supply cord is damaged, it must be replaced by the
manufacturer or an authorised BLACK+DECKER Service
Centre in order to avoid a hazard.
u When using the tool outdoors, only use extension
cables intended for outdoor use. A suitable rated
BLACK+DECKER extension cable of up to 30 m can be
used without loss of power.
Correct hand position (Fig. D)
Always hold the trimmer, as shown in the illustrations in this
manual, with one hand on the switch handle and one hand on
the auxiliary handle (Fig. D). Never hold the unit by the blade
guard.
Use
u Electric safety can be further improved by using a high-
sensitivity 30 mA residual current device (RCD).
Warning! Let the tool work at its own pace. Do not overload.
Switching on and off
Features
Note: For your safety, this tool is equipped with a double
switching system. This system prevents starting the tool
inadvertently and will only allow operation while holding the
tool with both hands.
This tool includes some or all of the following features.
1. Blade
2. Guard
3. Auxiliary handle
4. Lock off button
5. Trigger switch
6. Switch handle
7. Cord retainer
Switching on (fig. E)
u To turn the tool “ON”, press the lock off button (4) in the
auxiliary handle (3) backward and squeeze the trigger
switch (5) . Once the unit is running, you may release the
lock off button. In order to keep the unit running you must
continue to squeeze the trigger. To turn the tool “OFF”,
release the trigger.
8. Sawblade
9. Sawblade shoe
Assembly
Warning! Never attempt to lock a switch in the ON position.
u Regularly oil the blades.
Warning! Before assembly, make sure that the tool is
switched off and unplugged and that the blade sheath is fitted
over the blades.
Guidelines for trimming
Attaching guard to trimmer (fig. A, B)
The trimmer is shipped with the guard unattached to the trim-
mer. To attach the guard:
Extension cord (fig. F)
u Always keep extension cord behind trimmer and away
from the trimming operation as shown in figure F. Never
drape it over a hedge being trimmed.
6
(Original instructions)
ENGLISH
If you cut or damage the cord, unplug it at the electrical
outlet immediately, before inspecting or repairing cord.
Accessories
The performance of your tool depends on the accessory used.
BLACK+DECKER accessories are engineered to high quality
standards and designed to enhance the performance of your
tool. By using these accessories you will get the very best
from your tool.
Working position
u Maintain proper footing and balance and do not over-
reach.
u Wear safety goggles, non-skid footwear and rubber gloves
when trimming.
u Hold the tool firmly in both hands and turn the tool ON.
Always hold the trimmer, as shown in Fig. D, with one
hand on the switch handle and one hand on the auxiliary
handle. Never hold the tool by the blade guard.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool care and regular cleaning.
Lubrication oil is available from your BLACK+DECKER dealer
(cat. no. A6102-XJ).
Trimming new growth (fig.G)
u A wide, sweeping motion, feeding the blade teeth through
the twigs is most effective. A slight downward tilt of the
blade, in the direction of motion gives the best cutting.
Warning! Do not use trimmer for cutting stems greater than
16 mm. Use the trimmer only for cutting normal shrubbery
found around houses and buildings.
Warning! Before performing any maintenance on corded/
cordless power tools:
u Switch off and unplug the appliance/tool.
u Or switch off and remove the battery from the appliance/
tool if the appliance/tool has a separate battery pack.
u Or run the battery down completely if it is integral and then
switch off.
Level hedges (fig.H)
u To obtain exceptionally level hedges, a piece of string can
be stretched along the length of the hedge as a guide.
u Unplug the charger before cleaning it. Your charger does
not require any maintenance apart from regular cleaning.
u Regularly clean the ventilation slots in your appliance/tool/
charger using a soft brush or dry cloth.
Side trimming hedges (fig.I)
u Begin at the bottom and sweep up.
u Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
u After use, carefully clean the blades. After cleaning, apply
a film of light machine oil to prevent the blades from rust-
ing.
Sawblade (fig.J)
u For branches too large for the blade (1) to cut, use the
sawblade (8) . Position the sawblade as close to the
bottom of the branch as possible. Place the sawblade
shoe (9) against the branch. Turn the hedge trimmer on as
described above, allowing the tool to work at its own pace
until the branch is fully cut.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
u Safely dispose of the old plug.
The cutting blades are made from high quality, hardened steel
and with normal usage, they will not require resharpening.
However, if you accidentally hit a wire fence (Fig. L), stones,
glass or other hard objects, you may put a nick in the blade.
There is no need to remove this nick as long as it does not in-
terfere with the movement of the blade. If it does interfere, un-
plug the cord and use a fine toothed file or sharpening stone
to remove the nick. If you drop the trimmer, carefully inspect it
for damage. If the blade is bent, housing cracked, or handles
broken or if you see any other condition that may affect the
trimmer’s operation contact your local BLACK+DECKER
Service Center for repairs before putting it back into use.
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. Do not store the
unit on or adjacent to fertilizers or chemicals.
u Connect the brown lead to the live terminal in the new
plug.
u Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 5 A.
Protecting the environment
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
7
Troubleshooting
Problem
BEHTS501
Type 1
Possible Cause
Possible Solution
Voltage
VAC
W
230
600
Slow running, noisy or
hot blades.
Dry, corroded blades.
Lubricate blades.
Power input
Blades or blade support Straighten blade or
bent. blade support.
Blade strokes
(no load)
min-
1840
1
Bent or damaged teeth. Straighten teeth.
Blade length
Blade gap
cm
60
25
Loose blade bolts.
Tighten blade bolts.
mm
Unit will not start.
Lock off not fully
operated.
Check that lock off is
fully forward prior to
moving main trigger.
Blade brake
time
s
<1
Cord not plugged in.
Circuit fuse is blown.
Plug cord into a work-
ing outlet.
Saw blade Max
cut
mm
kg
35
Replace circuit fuse.
(If the product repeat-
edly causes the circuit
fuse to blow, discon-
tinue use immediately
and have it serviced
at a BLACK+DECKER
service center or
Weight
2.65
Level of sound pressure according to EN 60745:
Sound pressure level at operator position (LpA) 89 dB(A), uncertainty (K) 3.5 dB(A)
Sound power level (LWA) 98 dB(A), uncertainty (K) 2.0 dB(A)
authorized servicer.)
Circuit breaker is
tripped.
Reset circuit breaker.
(If the product repeat-
edly causes the circuit
breaker to trip, discon-
tinue use immediately
and have it serviced
at a BLACK+DECKER
service center or
Vibration total values (triax vector sum) according to EN 60745:
Vibration emission value (ah, D) 4.1 m/s2, uncertainty (K) 2.1 m/s2
EC declaration of conformity
MACHINERY DIRECTIVE
authorized servicer.)
OUTDOOR NOISE DIRECTIVE
Cord or switch is
damaged.
Have cord or
switch replaced at
BLACK+DECKER
Service Center or
Authorized Servicer.
Technical data
BEHTS301, BEHTS401, BEHTS451, BEHTS501 – Hedge
Trimmer
BEHTS301
Type 1
BEHTS401
Type 1
BEHTS451
Type 1
Black & Decker declares that these products described under
"technical data" are in compliance with:
Voltage
VAC
W
230
500
230
230
550
Power input
500
2006/42/EC, EN 60745-1:2009 +A11:2010,
EN 60745-2-15:2009 +A1:2010
Blade strokes
(no load)
min-
1850
1835
1870
1
Blade length
Blade gap
cm
50
22
55
22
60
25
2000/14/EC, Hedge trimmer, Annex V
Measured sound power level (LwA) 98 dB(A)
Uncertainty (K) 2,0 dB(A)
mm
Blade brake
time
s
<1
<1
<1
Guaranteed sound power (LwA) 100 dB(A)
Saw blade Max
cut
mm
kg
35
35
35
These products also comply with Directive
2014/30/EU and 2011/65/EU.
Weight
2.47
2.54
2.65
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
(Original instructions)
ENGLISH
The undersigned is responsible for compilation of the technical
file and makes this declaration on behalf of Black & Decker.
R. Laverick
Engineering Director
Black & Decker Europe, 210 Bath Road, Slough,
Berkshire, SL1 3YD
United Kingdom
26/10/2017
Guarantee
Black & Decker is confident of the quality of its products and
offers consumers a 24 month guarantee from the date
of purchase. This guarantee is in addition to and in no way
prejudices your statutory rights. The guarantee is valid within
the territories of the Member States of the European Union
and the European Free Trade Area.
To claim on the guarantee, the claim must be in accordance
with Black&Decker Terms and Conditions and you will need to
submit proof of purchase to the seller or an authorised repair
agent. Terms and conditions of the Black&Decker 2 year
guarantee and the location of your nearest authorised repair
by contacting your local Black & Decker office at the address
indicated in this manual.
your new Black & Decker product and receive updates on new
products and special offers.
9
(Original instructions)
ENGLISH
10
(Original instructions)
ENGLISH
11
Australia
Black & Decker (Australia) Pty. Ltd.
20 Fletcher Road, Mooroolbark,
Victoria, 3138
Tel.
Fax
03-8720 5100
03-9727 5940
New Zealand
Black & Decker
5 Te Apunga Place
Mt Wellington
Tel.
Fax
+64 9 259 1133
+64 9 259 1122
Aukland 1060
United Kingdom &
Republic Of Ireland
Black & Decker
210 Bath Road
Tel.
Fax
01753 511234
01753 512365
Slough, Berkshire SL1 3YD
N523972 REV-00
10/2017
|