STEAM MOP
INSTRUCTION MANUAL
Catalog Number
bDH1760Sm
Thank you for choosing Black & Decker! To register your new product, go to
PLeASe ReAD BefORe ReTURNINg ThIS PRODUCT fOR ANy ReASON.
If you have a question or experience a problem with your Black & Decker purchase, go to
If you can’t find the answer or do not have access to the Internet,
call 1-800-544-6986 from 8 a.m. to 5 p.m. eST Mon. - fri. to speak with an agent.
Please have the catalog number available when you call.
SAve ThIS MANUAL fOR fUTURe RefeReNCe.
veA eL eSPANOL eN LA CONTRAPORTADA.
INSTRUCTIvO De OPeRACIÓN, CeNTROS De SeRvICIO y PÓLIZA De gARANTÍA.
ADveRTeNCIA: LÉASe eSTe INSTRUCTIvO ANTeS De USAR eL PRODUCTO.
• Do not leave the appliance connected to an electrical outlet when not in use.
• Never pull the power cord to disconnect the appliance from the socket. Keep the
appliance cord away from heat, oil and sharp edges.
• Do not handle steam cleaner with wet hands.
• Do not pull or carry by cord, use cord as a handle, close door on cord, pull cord around
sharp corners or expose cord to heated surfaces.
•
Do not use appliance in an enclosed space filled with vapor given off by oil-based paint
thinner, some moth-proofing substances, flammable dust, or other explosive or toxic vapors.
• Do not use on leather, wax polished furniture or floors, synthetic fabrics, velvet or other
delicate, steam-sensitive materials.
• Do not use on any unsealed hard floor surfaces. Additionally, on surfaces that have been
treated with wax or some no-wax floors, the sheen may be removed by the heat and
steam action. It is always recommended to test an isolated area of the surface to be
cleaned before proceeding. We also recommend that you check the use and care
instructions from the floor manufacturer.
• Never put de-scaling, aromatic, alcoholic or detergent products into the steam mop, as
this may damage it or make it unsafe for use.
•
If the circuit breaker activates while using the steam function, discontinue product use
immediately and contact the customer support center. (Beware of the risk of electrical shock.)
• The appliance emits very hot steam to sanitize the area of use. This means that the
steam head and cleaning pads get very hot during use.
CautIoN: Always wear suitable shoes when using your steam mop and when
changing the accessories on your steam mop. Do not wear slippers or open-toed footwear.
• Steam may escape from the appliance during use.
• Care should be taken when using this appliance. DO NOT touch any parts which may
become hot during use.
after uSe
• Unplug the appliance and allow to cool down on resting mat before cleaning.
• When not in use, the appliance should be stored in a dry place.
• Children should not have access to stored appliances.
INSPeCtIoN aND rePaIrS
• Unplug the appliance and allow to cool down on resting mat before performing any
maintenance or repairs.
• Before use, check the appliance for damaged or defective parts. Check for breakage of
parts, damage to switches and any other conditions that may affect its operation.
• Regularly check the power cord for damage.
• Do not use the appliance if any part is damaged or defective.
• Have any damaged or defective parts repaired or replaced by an authorized repair agent.
• Never attempt to remove or replace any parts other than those specified in this manual.
Safety of otHerS
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance by
a person responsible for their safety.
• Children should be supervised to ensure that they do not play with the appliance.
reSIDual rISkS
Additional residual risks may arise when using the tool which may not be included in the
enclosed safety warnings. These risks can arise from misuse, prolonged use, etc.
Even with the application of the relevant safety regulations and the implementation of
safety devices, certain residual risks can not be avoided. These include:
• Injuries caused by touching any moving parts.
• Injuries caused by touching any hot parts.
• Injuries caused when changing any parts or accessories.
• Injuries caused by prolonged use of the appliance. When using any appliance for
prolonged periods ensure you take regular breaks.
3
fuNCtIoNal DeSCrIPtIoN
1. oN/off switch
a
2. SmartSelecttm
button
3. removable
Water tank
4. Handle tube
5. Steam Head
6. micro-fiber
Cleaning Pad
7. resting mat
8. Carpet glider
9. lift and reach
Head Cleaning Pad
aSSembly
NotICe: Each steam mop is 100% tested in the factory to ensure product
performance and safety. When assembling your new steam mop for the first time you
may notice water residue inside of the unit.
WarNINg: Before attempting any of the
following operations, make sure that the appliance is
switched off and unplugged and that the appliance is
cold and contains minimal or no water.
b
attaCHINg tHe HaNDle - fig. b & l
• With the cord hooks (21 & 22) toward the back of the
appliance, slide the bottom end of the handle tube (4)
into the top end of the steam mop body (11) until it is
firmly seated and clicks into place.
attaCHINg tHe Steam HeaD - fig. C
• Slide the bottom end of the steam mop body (11)
onto the steam head (5) until it clicks into place.
• The steam head can be removed from the steam
mop body by pressing the steam head release
button (13) and pulling the steam mop body off the
steam head.
C
attaCHINg tHe Water taNk
• Clip the water tank (3) onto the handle (4).
• Slide the water tank down into the steam mop body
(11), ensure that the water tank is firmly seated.
4
attaCHINg a CleaNINg PaD - fig. D
Replacement cleaning pads are available from
your Black & Decker dealer (cat. no. SMP20).
• Place a micro-fiber cleaning pad (6) on the
D
floor with the ‘hook & loop’ side facing up.
• Raise the steam mop off the resting mat
(7) and press it down onto the cleaning pad
(6). You are now ready to steam clean and
sanitize your floor.
NotICe: Always place the steam mop on
the resting mat (7) with the handle tube (4)
in the upright position when stationary and
make sure the steam mop is turned off when
not in use.
remoVINg a CleaNINg PaD - fig. e
CautIoN: Always wear suitable shoes
e
when changing the cleaning pad on your
steam mop. Do not wear slippers or
open-toed footwear.
• Return the handle tube (4) to the upright
position and turn the steam mop ‘OFF’.
• Place the steam mop on the resting mat and
wait until it cools down. (approximately five
minutes)
•
Place the front of your shoe onto the cleaning
pad removal tab (14) and press down firmly.
• Lift the steam mop up off the cleaning pad.
NotICe: Always place the steam mop on
the resting mat (7) with the handle tube (4) in the upright position when stationary and
make sure the steam mop is turned off when not in use.
attaCHINg tHe CarPet glIDer - fig. f
• Place carpet glider on the floor.
• Lightly press the steam mop with attached
cleaning pad down onto the carpet glider (8)
until it clicks into place.
f
NotICe: Always place the steam mop on
the resting mat (7) with the handle (4) in the
upright position when stationary and make sure
the steam mop is turned off when not in use.
remoVINg tHe CarPet glIDer
CautIoN: Always wear suitable shoes
when changing the carpet glider on your
steam mop. Do not wear slippers or open-toed footwear.
• Return the handle to the upright position and turn the steam mop ‘OFF’.
• Place the steam mop on the resting mat and wait until it cools down. (approximately
five minutes)
• Place the front of your shoe onto the carpet glider removal tab (15) and press down firmly.
• Lift the steam mop up off the carpet glider.
NotICe: Always place the steam mop on the resting mat (7) with the handle (4) in the
upright position when stationary and make sure the steam mop is turned off when not in use.
5
tHe lIft aND reaCH HeaD - fig. g
This Steam Mop incorporates a built in Lift
and Reach Head which enables you to access
tight corners and narrow gaps.
g
CautIoN: Always wear suitable shoes
when accessing the Lift and Reach Head on
your steam mop. Do not wear slippers or
open-toed footwear.
to aCCeSS tHe lIft aND
reaCH HeaD:
• Return the handle to the upright position and
turn the steam mop ‘OFF’.
•
•
Place the steam mop on the resting mat and wait until it cools down. (approximately five minutes
Place the front of your shoe onto the steam head removal tab (15) and press down gently.
)
• Lift the Lift and Reach Head up off the steam head (5).
Place the Lift and Reach Head cleaning pad (9) on the floor with the ‘hook & loop’ side facing up.
• Raise the Lift and Reach Head off the resting mat (7) and press it down onto the
•
cleaning pad (9). You are now ready to steam clean and sanitize your floor.
to re-fIt tHe lIft aND reaCH HeaD:
• Return the handle tube (4) to the upright position and turn the steam mop ‘OFF’.
• Place the steam mop on the resting mat and wait until it cools down. (approximately
five minutes)
• Place the front of your shoe onto the Lift and Reach Head cleaning pad removal tab
and press down firmly.
• Lift the Lift and Reach Head (16) up off the cleaning pad.
• Place the tip of the Lift and Reach Head into the steam head (5) and push downward.
Ensure it is locked into place by gently pulling upwards on the handle.
NotICe: Always place the steam mop on the resting mat (7) with the handle tube (4) in the
upright position when stationary and make sure the steam mop is turned off when not in use.
fIllINg tHe Water taNk - fig. H & I
This Steam Mop incorporates an anti-calcium system to help prolong the life of the system.
NotICe: The water tank is conveniently
H
removable for easier use.
NotICe: Fill the water tank with regular tap water.
NotICe: In areas of very hard water, the
use of de-ionized water is recommended.
WarNINg: Do not overfill the tank.
Only fill to bottom of hole with water tank in
vertical position.
•
Ensure that the appliance is switched off
and the power cord is disconnected from the
power supply.
•
Place the steam mop on the resting mat (7)
with the handle tube (4) in the upright position.
I
• Remove the water tank (3) by pulling it
upwards.
• Open the filler cap (18) by lifting it up.
• Fill the water tank (3) with water to the bottom
of the hole with tank in vertical position.
• Close the filler cap.
• Re-install the water tank onto the steam
mop body (11) and ensure it is firmly seated.
NotICe: Always empty the water tank after
use.
6
oPeratIoN
SWItCHINg oN aND off - fig. J
J
CautIoN: for floor uSe oNly;
Do Not uSe tHe uNIt uPSIDe DoWN.
NotICe: When the steam mop is first
turned on the water reservoir will glow red.
Once the steam mop is ready to use the water
reservoir will glow blue. It takes approximately
15 seconds for the steam mop to heat up.
• To switch the appliance on, press the ON/
OFF button (1).
• To switch the appliance off, press the ON/
OFF button.
NotICe: Never leave the steam mop in one spot on any surface for any period of time.
Always place the steam mop on the resting mat (7) with the handle tube (4) in the upright
position when stationary and make sure the steam mop is turned off when not in use.
NotICe: Always empty the water tank after use.
SmartSelecttm Dial - fig. k
k
The steam mop is equipped with a
SmartSelectTM dial (20) which shows various
hard floor surface cleaning applications.
A Light will glow next to the selected
application. To change the application, press
and release the SmartSelectTM button (2)
repeatedly until the light glows next to the
correct operating mode for your particular
hard floor surface.
20
NotICe: Do not use on any unsealed
hard floor surfaces. Additionally, on surfaces
that have been treated with wax or some no
wax floors, the sheen may be removed by the heat and steam action. It is always
recommended to test an isolated area of the surface to be cleaned before proceeding.
We also recommend that you check the use and care instructions from the floor
manufacturer.
using the SmartSelecttm button (2), choose from one of the following applications:
The steam mop will select the correct volume of steam required for your particular
cleaning operation.
NotICe: SmartSelecttm has a memory. Switching the steam mop on will recall the
previously used setting.
Steam burSt buttoN - fig. k
The steam burst button is a built in feature that aids in the removal of stubborn floor marks or
stuck on grime.
• To apply an extra burst of steam to trouble areas, press the Steam Burst button (19).
NotICe: The steam burst will last for 10 seconds then the steam mop will return to
the chosen setting.
7
NotICe: This unit will kill 99.9% of bacteria and germs when used in accordance with
this manual and with the micro fiber pad fitted and a continuous run time of 90 seconds
HINtS for oPtImum uSe
geNeral uSe
CautIoN: Never use the steam mop without first attaching a cleaning pad.
WarNINg: It is important to monitor the water level in the water tank. To refill the
water tank and continue to sanitize/clean, see Filling the Water Tank section.
CautIoN: Never leave the steam mop in one spot on any surface for any period of
time. Always place the steam mop on the resting mat (7) with the handle tube in the upright
position when stationary and make sure the steam mop is turned off when not in use.
• Always vacuum or sweep the floor before using the steam mop.
• The easiest way to use the steam mop is to tilt the handle to a 45˚ angle and clean
slowly, covering a small area at a time.
• Do not use chemical cleaners with your steam mop. To remove stubborn stains
from vinyl or linoleum floors, you can pre-treat them with a mild detergent and some
water before using the steam mop.
Steam CleaNINg
• Place a cleaning pad (6) on the floor with the ‘hook & loop’ side facing up.
• Raise the steam mop off the resting mat (7) and lightly press it down onto the cleaning pad.
• Place the steam mop on the resting mat.
• Plug the steam mop electric cord into the outlet.
• Press the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
• Press the SmartSelecttm button (2) until the required setting is reached.
• Pulling the handle tube (4) back will activate the steam pump. After a few seconds
steam will start to come out of the steam head.
NotICe: If the system has been run dry it may take up to 30 seconds to prime the
system on first use.
• It takes a few seconds for steam to enter the cleaning pad. The steam mop will now
glide easily over the surface to be sanitized/cleaned.
•
Push and pull the steam mop slowly across the floor to thoroughly steam clean each section.
NotICe: During use you may turn off the steam pump by returning the handle to
the upright position, this convenient feature will allow you to place the steam mop on
the resting mat for a short time so that you may move items of furniture, then continue
cleaning without the need to switch the appliance off.
CarPet refreSHINg
WarNINg: It is important to monitor the water level in the water tank. To refill the
water tank and continue to sanitize/ clean, return the handle tube (4) to the upright position
and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet, remove and refill
the water tank (3).
CautIoN: Never leave the steam mop in one spot on any surface for any period
of time. Always place the steam mop on the resting mat (7) with the handle tube in the upright
position when stationary and make sure the steam mop is turned off when not in use.
• Place the carpet glider (8) on the floor.
• Lightly press the steam mop with attached cleaning pad down onto the carpet glider
until it clicks into place.
• Place the steam mop on the resting mat.
• Plug the steam mop electric cord into the outlet.
•
Press the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
• Press the SmartSelecttm button (2) to the Wood/Laminate setting.
• Pulling the handle tube back will activate the steam pump. After a few seconds steam
will start to come out of the steam head.
•
Push and pull the steam mop slowly across the carpet to thoroughly refresh each section.
NotICe: During use you may turn off the steam pump by returning the handle tube to the
upright position, this convenient feature will allow you to place the steam mop on the resting
mat so that you may move items of furniture with out the need to switch the appliance off.
8
after uSe - fig. l
l
• Return the handle tube (4) to the upright
position and turn the steam mop ‘OFF’.
• Place the steam mop on the resting mat (7)
and wait until the steam mop cools down.
(approximately five minutes)
• Unplug the steam mop from the wall outlet.
• Empty the water tank (3).
• Remove the cleaning pad (6) and wash it
so that it is ready for the next use. (Take
care to follow the wash care instructions
printed on the cleaning pad).
• Wrap the electric cord around the cord
hooks (21 & 22).
NotICe: The top cord hook rotates to easily release the cord ready for next use.
• Place steam mop on the resting mat for storage.
NotICe: With the handle tube in the upright position, the cord neatly wrapped
around the cord hooks, your steam mop will stand on its own for storage. Alternatively
there is a hanging bracket built into the hand grip which will allow your steam mop to be
hung from a suitable hook on the wall. Always ensure that your wall hook is capable of
supporting the weight of the steam mop safely.
maINteNaNCe aND CleaNINg
Your Black & Decker corded appliance has been designed to operate over a long period
of time with a minimum of maintenance. Continuous satisfactory operation depends
upon proper appliance care and regular cleaning.
WarNINg: Before performing any maintenance or cleaning on corded
appliances switch off and unplug the appliance.
• Clean your appliance using a soft damp cloth. Never let any liquid get inside the
appliance; never immerse any part of the appliance into a liquid. ImPortaNt: To
assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment
should be performed by authorized service centers or other qualified service
organizations, always using identical replacement parts.
•
For stubborn marks you can use a mild solution of soap and water to dampen your cloth.
Care of tHe CleaNINg PaDS
NotICe: Follow the cleaning instructions printed on the label of your cleaning pad.
Wash care instructions - Machine wash warm 140°F (60°C) - No bleach - No fabric
softener - Air dry only - Allow to dry fully before re-use.
aCCeSSorIeS
Recommended accessories for use with your appliance are available from your local
dealer or authorized service center. If you need assistance regarding accessories, please
call: 1-800-544-6986.
WarNINg: The use of any accessory not recommended for use with this
appliance could be hazardous.
9
troubleSHootINg
PoSSIble CauSe
• Cord not plugged in.
Problem
•Unit will not start.
PoSSIble SolutIoN
• Plug appliance into a working
outlet.
• Turn main switch on.
• Main switch not on.
• Floor head not correctly • Ensure floor head is correctly
fitted.
attached.
• Fit Handle correctly
• Handle not fitted
correctly - LED’s do not
light up.
• Circuit fuse is blown.
• Replace circuit fuse. (If the
product repeatedly causes the
circuit fuse to blow, discontinue
use immediately and have it
serviced at a Black & Decker
service center or authorized
servicer.)
• Circuit breaker is tripped. • Reset circuit breaker. (If the
product repeatedly causes the
circuit breaker to trip,
discontinue use immediately
and have it serviced at a Black &
Decker service center or
authorized servicer.)
• Cord or switch is
damaged.
• Have cord or switch replaced
at a Black & Decker Service
Center or Authorized Servicer.
• Mop will not make steam. • No water in water tank. • Add water to the water tank.
• Tank not fitted correctly. • Ensure tank is fully attached and
seated.
• Mop leaves water on floor. • Cleaning pad is too wet. • Unplug unit from power outlet
and change the micro-fiber
cleaning pad.
• Mop left spot on floor.
• Mop left in one spot too • Never leave the steam mop on
long.
the floor with a damp or wet
cleaning pad still attached when
not in use.
• Hard water.
• Use distilled water.
For assistance with your product, visit our website www.blackanddecker.com for the
location of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
10
|