HEATED BASE-HB SERIES
Service and Installation Manual
Please read this manual completely before attempting to install or operate this equipment!
Notify carrier of damage! Inspect all components immediately. See page 2.
HEATED BASE-HB SERIES
ELECTRICALLY HEATED
UNDER-COUNTER
Effective Date: 2019
IMPORTANT INFORMATION
READ BEFORE USE
Project: ___________
Item No.:ꢀ ___________
Quantity:ꢀ ___________
SLIDE-IN SERVING EQUIPMENT
HEATED
HB-3
HB-4
HB-5
BASE
Electrically Heated
Under Counter
HB-3
STANDARD FEATURES
Slides into your counter - puts heated storage where
you need it
Fully insulated for maximum efficiency
Slide assembly for standard 12” x 20” pans
SPECIFICATIONS
g
BODY: Double wall constructed with 20 gauge, type 304
stainless steel interior liner, with coved corners. Exterior wall
is 22 gauge galvanized steel, with an 18 gauge stainless
steel facia. The body is filled with 1" of high density fiber-
glass insulation on all sides. Interior of the body is provided
with a removable slide assembly to accommodate 12" X 20"
pans.
g
g
g Electrically heated - thermostat control
g 1-Year Parts &ꢀLabor Warranty
g
UL Listed
DOORS: Doors are double wall constructed of 18 gauge,
type 304 stainless steel, fully insulated with high density
fiberglass, and provided with edge mounted, chrome plated
hinges and a slam action latch. Doors are complete with a
moisture-proof gasket.
ELECTRICAL: The unit is provided with an 850 watt ele-
ment, pre-wired to an on/off thermostat switch and pilot light.
The unit is wired for 15 amp., 120 volt, single phase opera-
tion, with a 6’ long, 3-wire cord and plug (NEMA 5-15P).
Specifications subject to change without notice.
DI-57
“A”
23-5/8”
PLAN VIEW
15-3/4”
14-5/8”
14-1/8”
15-1/2”
FRONT ELEVATION
29-1/8”
END VIEW
STORAGE CAPACITY
12” X 20” PANS
CUT-OUT
ELECTRICAL
SHIP WT.
MODEL
HB-3
“A”
REQUIRED
CHARACTERISTICS (LBS.)
41-7/8”
(106cm)
15-3/4” X 41-7/8” 850 W - 7.1 amps.
(40 X 106cm) 120V
190
(86.1kg)
8
55-5/8”
15-3/4” X 55-5/8” 850 W - 7.1 amps.
(40 X 140.9cm) 120V
265
HB-4
12
16
(140.9cm)
(120.2kg)
69-3/8”
(175.8cm)
15-3/4” X 69-3/8” 850 W - 7.1 amps.
(40 X 175.8cm) 120V
312
(141.5kg)
HB-5
Atlas Metal Industries 1135 NWꢀ159th Dr. Miami, FL 33169 (800) 762-7565 Fax: (305) 623-0475 atlasfoodserv.com
DI-58
2/19-sc
SLIDE- IN HEATED BASE
HB SERIES
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
OPERATION
The unit is ready to operate as soon as it is plugged in and turned on. The thermostat has an off position and
numbers from #1 through #10 (number 10 is the highest setting).
The unit is supplied with a power cord and NEMA plug. Refer to the data plate for the amperage and voltage
information. Use a licensed electrician when installing power source.
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
--------------------------------------------------------------------------------------------------------------------------------------------------------------------
MAINTENANCE
NEVER CLEAN THE UNIT WITH A CHLORIDE BASED PRODUCT. CHLORIDES OR IMPROPER
CLEANING COULD SCAR, MARK AND/OR CORRODE METAL. DO NOT USE STEEL WOOL OR
ABRASIVE PRODUCTS. TO CLEAN USE SOAPY WARM WATER, RINSE THOROUGHLY TO REMOVE
ALL RESIDUES. FAILURE TO MEET THESE CONDITIONS WILL VOID WARRANTY.
Subsidiary of Mercury Aircraft, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: [email protected]
PARTS LIST ELECTRICAL HEATED BASE
HB SERIES
1
2
6
7
3
4
5
8
H B -4 S H O W N
9
10
ITEM
P ART
DESCRIPTION
NUMBER
NUMBER
1001-0
Power Cord 14/3-15 Amps 240V
1
1002-0
22-1407
1100-0
1105-0
7010-3
7013-3
S83754-4
S83753-0
6055-1
6052-1
S83754-3
6053-8
1087-0
2500-1
1053-0
Power Cord 14/3-15 Amps 120V
Thermostat Knob
2
3
4
Pilot Light
Thermometer
#3 & #4 Door Gasket
#4 & #5 Door Gasket
Door Assembly HB-5
Pan Rack
5
6
7
Slam Action Latch
8
Slam Action W/ Lock
Door Assembly HB-3, HB-4
Hinge & Cover
9
10
11
12
Cord Connector (Not Shown)
Thermostat (Not Shown)
120V / 850W Element (Not Shown)
208V / 850W Element (Not Shown)
240V / 850W Element (Not Shown)
13
1054-0
1055-0
Subsidiary of Mercury Aircraft, Inc.
1135 N.W. 159th DR., MIAMI, FL 33169
PHONE (305) 625-2451, (800) 762-7565, FAX (305) 623-0475, E-mail: [email protected]
Electric Hot Food Drop-In Trouble Shooting Guide
Symptom
Probable Cause
Unit not plugged in.
No power at receptacle.
Thermostat and or switch not in the on position.
Call factory for service at 1-800-762-7565
Unit will not heat
Thermostat’s not turned to the highest setting.
Food products not hot enough when placed in unit.
Food product not being stirred or rotated.
Heat lamp or head strip over the food product is recommended.
Call factory for service at 1-800-762-7565.
Food products not
hot enough.
NOTE:
Before starting any warranty repair work you must first call the factory for authorization.
Failure to do so can make you responsible for repair cost.
LIMITED WARRANTY
Atlas Metal Industries, Inc. warrants to the Purchaser of this product that the
same shall be free from defects in the workmanship and material for a period of
one year from the date of original installation of the equipment, but not to exceed
eighteen (18) months after date of shipment from factory. During this period of
time Atlas Metal Industries, Inc. will replace all defective parts and will pay for
authorized replacement labor. Replacement and installation of such parts and
labor shall be provided only upon prior written authority of Atlas Metal Industries,
Inc.
The Refrigeration warranty is for a twenty (20) month time period and includes
supplying the compressor at a no charge basis provided the damage to the
compressor was not caused by the customer or end user. Authorized
replacement labor will be paid for a period of one year from date of installation.
Freight costs for defective unit to and from Atlas Metal Industries, Inc. are not
included, and all defective parts must be returned to the factory freight prepaid
for evaluation. ALL WARRANTY LABOR MUST BE AUTHORIZED BY ATLAS
METAL INDUSTRIES, INC. PRIOR TO THE ACTUAL WORK BEING DONE.
This warranty does not apply to any equipment or any part thereof, which has
been subjected to shipping damage, improper voltage, alteration, abuse or
misuses, and does not cover loss of food, other products, or damage to property
due to mechanical or electrical malfunction.
THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION OF THE FACE HEREOF. SELLER DISCLAIMS ANY IMPLIED
WARRANTY OF MERCHANTABILITY OF THE GOODS OR THE FITNESS OF
THE GOODS FOR ANY PURPOSE AND BUYER AGREES THAT THE GOODS
ARE SOLD “AS IS.”
WARRANTY INFORMATION
In order to have your invoice approved for
payment by the factory, please note the following:
_______________________________________________
An authorization number must be obtained from
the factory prior to performing any warranty
service.
_______________________________________________
Atlas Metal will not approve excessive labor due to poor
access to the unit being serviced. If design does not
allow reasonable access, contact the factory.
_______________________________________________
All travel time that exceeds 100 miles round trip
must be authorized by the factory.
_____________________________________________________________________________________
Thank You:
Warranty service Dept.
|