Acer Projector
P1287/M416/PE-X45
P1387W/M426/PE-W45
P5515/N156/PN-805
H6517BD/E145D/HE-801J
H6517ST/E145S/HE-801ST Series
User's Guide
iii
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•
•
•
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
•
•
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices, lamp.
Using electrical power
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
•
•
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
•
•
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
•
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
Do not look into the projector's lens when the lamp is on. The bright may
hurt your eyes.
•
•
Turn on the projector first and then signal sources
Do not place the product in following environments:
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
•
•
•
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
•
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
vi
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
•
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
•
•
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
•
Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off
before turning main power off.
•
•
Do not touch air outlet grille and bottom plate which becomes hot.
Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
•
•
•
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire. To temporarily turn off the lamp, press HIDE
on the remote control.
•
The lamp becomes extremely hot during operation. Allow the projector to
cool for approximately 45 minutes prior to removing the lamp assembly for
replacement.
•
•
•
•
•
•
Do not operate lamps beyond the rated lamp life. It could cause it to break
on rare occasions.
Never replace the lamp assembly or any electronic components unless the
projector is unplugged.
The product will detect the life of the lamp itself. Please be sure to change
the lamp when is showing warning message.
When changing the lamp, please allow unit to cool down, and follow all
changing instructions.
Reset the "Lamp Hour Reset" function from the Onscreen display
"Management" menu after replacing the lamp module.
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. The only user serviceable part is the
lamp which has its own removable cover. Refer servicing only to suitable
qualified professional service personnel.
•
•
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
This product is capable of displaying inverted images for ceiling mount
installation. Only use acer ceiling mount kit for mounting the projector
and ensure it is securely installed.
vii
Caution for Listening
To protect your hearing, follow these instructions.
•
•
•
•
•
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
Mercury advisory
For projectors or electronic products containing an LCD/CRT monitor or display:
“Lamp(s) contain Mercury,
Dispose Properly.”
Lamp(s) inside this product contain mercury and must be recycled or disposed of
according to local, state or federal laws. For more information, contact the
information, check www.lamprecycle.org
viii
First things first
Usage Notes
Do:
•
•
Turn off the product before cleaning.
Use a soft cloth moistened with mild detergent to clean the display
housing.
•
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•
•
•
Block the slots and openings on the unit provided for ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
•
•
•
•
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•
•
Do not look into the projector's lens when the lamp is on. The bright light may hurt
your eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•
•
Please do not open or disassemble the product as this may cause electric shock.
When changing the lamp, please allow unit to cool down, and follow all changing
instructions.
•
•
•
This product will detect the life of the lamp itself. Please be sure to change the lamp
when it shows warning messages.
Reset the "Lamp Hour Reset" function from the Onscreen display "Management"
menu after replacing the lamp module.
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•
•
•
Turn on the projector first and then the signal sources.
Do not use lens cap when projector is in operation.
When the lamp reaches the end of its life, it will burn out and may make a loud
popping sound. If this happens, the projector will not turn back on until the lamp
module has been replaced. To replace the lamp, follow the procedures listed under
"Replacing the Lamp".
Information for your safety and comfort
First things first
Usage Notes
Precautions
Introduction
Product Features
Package Overview
Projector Overview
Projector Outlook
Control Panel
Remote Control Layout
Getting Started
Connecting the Projector
11
11
12
13
13
Turning the Projector On/Off
Turning on the Projector
Turning the projector off
Adjusting the Projected Image
Adjusting the Height of Projected Image
How to optimize image size and distance
distance and zoom
User Controls
26
28
31
33
34
35
35
36
Installation menu
Color
Image
Setting
Management
Audio
3D
Language
Acer LAN webpage management
How to login in
Home
Control Panel
Network Setting
Alert Setting
Logout
Appendices
40
44
45
46
47
50
53
Troubleshooting
LED & Alarm Definition Listing
Cleaning and replacing the dust filters
Replacing the Lamp
Ceiling Mount Installation
Specifications
Compatibility modes
Regulations and safety notices
58
1
Introduction
Product Features
This product is a single-chip DLP® projector. Outstanding features include:
•
•
DLP® technology
P1287/M416/PE-X45 series: Native 1024 x 768 XGA resolution
P1387W/M426/PE-W45 series: Native 1280 x 800 WXGA resolution
P5515/N156/PN-805/H6517BD/E145D/HE-801J/H6517ST/E145S/HE-801ST
series: 1920x1080 1080p resolution
Full/4:3/16:9/L.Box aspect ratio supported
•
•
Enables projecting 3D content via DLP Link Technology (Nvidia 3DTV Play
Ready only on H6517BD/E145D/HE-801J/H6517ST/E145S/HE-801ST series)
Acer ColorBoost technology delivers nature’s true colors for vivid, life-like
images
•
•
High brightness and contrast ratio
Versatile display modes (Bright, Presentation, Standard, Video, Game,
Education, Movie, Dark Cinema, Sports, User) enable optimum
performance in any situation
•
•
•
NTSC / PAL / SECAM compatible and HDTV (720p, 1080i, 1080p) supported
Lower power consumption and economy (ECO) mode extends lamp life
Acer EcoProjeciton Technology delivers Intelligent power management
approach and physical efficiency improvement
•
•
•
•
•
•
Equipped with HDMI™ & MHL connection supporting HDCP
Advanced digital keystone correction optimizes presentations
Smart detection delivers quick, intelligent source detection
Multi-language onscreen display (OSD) menus
Manual focus projection lens zooms up to 1.0x / 1.1x / 1.2x / 1.36x
2x digital zoom and pan function
•
Microsoft® Windows® 2000, XP, Vista®, Windows 7, Windows 8,
Macintosh® OS compliant
Note: Functions vary depending on model definition.
2
Package Overview
This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.
Projector
Power cord
VGA cable
2 x Batteries
(option)
Security card
User’s guide
Quick start guide
Carrying case
(option)
Dust filters
(option)
Remote control
4
Right / Rear side
<Right side>
<Rear side>
4
1
2
3
5
6
7
8
10 11 12
13
14
4
9
VGA OUT
3
17
4
12
DC 5V OUT
VIDEO
12
1/ MHL
1
6
VGA IN
11
USB CTRL
1
15
11
AUDIO IN
1
LAN
15
10
2
16
7
8
AUDIO OUT AUDIO IN
2
RS 232
#
Description
#
Description
1
2
Composite video input connector
S-Video input connector
10 RS232 connector
11 Mini USB connector
Monitor loop-through output
connector (for VGA IN 2 only)
PC analog signal/HDTV/component
video input connector (VGA, VGA IN,
VGA IN 1, VGA IN 2)
12 HDMI/MHL connector (HDMI/MHL,
HDMI 1/MHL)
3
4
13
Power socket
KensingtonTM lock port
5
6
Security bar
14
Audio input connector (for S-Video,
Composite)
15 HDMI 2 connector
Audio input connector ( for S-Video,
Composite, VGA)
7
Audio out connector
16
Audio in connector (for VGA IN 1, VGA
IN 2)
LAN (RJ45 Port for 10/100M Ethernet)
8
9
17 5V DC output connector
Note: Functions vary depending on model definition.
5
Control Panel
1
8
2
3
4
9
5
10
7
6
#
Icon
Function
POWER
Description
1
Power Indicator LED
Lamp Indicator LED
Temp Indicator LED
2
3
4
LAMP
TEMP
RESYNC
Automatically synchronizes the projector
to the input source.
5
6
SOURCE
POWER
Changes the active source.
See the contents in "Turning the Projector
On/Off" section.
7
8
MODE
MENU
Press "MODE" to select the display mode
from Bright, Presentation, Standard, Video,
Game, Education and User.
•
Press "MENU" to launch the Onscreen
display (OSD) menu, back to the
previous step for the OSD menu
operation or exit the OSD menu.
•
Confirm your selection of items.
9
Four directional select
keys
Use
to select items or make
adjustments to your selection.
10
Keystone
Adjusts the image to compensate for
distortion caused by tilting the projector.
Note: Functions vary depending on model definition.
6
Remote Control Layout
1
25
26
3
4
2
SOURCE
SOURCE
HIDE
MEDIA
SETUP
MEDIA
SETUP
5
7
6
MODE
RATIO
HIDE
MODE
8
ZOOM
FREEZE
ZOOM
FREEZE
10
9
Model No:E-26281
11
12
13
14
16
15
17
19
18
20
22
24
21
23
Model No:E-26171
E-26110
LASER MODULE : M-5.2-6.5x10-5.5x5.5
BONTECH ELECTRONICS(K.S) CO ., LTD
No. 2018, Zhonghuayuan west road,
Yushan town,Kunshan city, China
.
MC.JG811.009
MC.JK211.004
#
Icon
Function
Description
1
2
3
Infrared
transmitter
Sends signals to the projector.
POWER
Refer to the "Turning the Projector On/Off" section.
3D
Press "3D" to select 3D models.
Changes the active source.
4
5
SOURCE
MODE
Press "MODE" to select the display mode from Bright,
Presentation, Standard, Video, Game, Education and User.
6
HIDE
Momentarily turns off the video. Press "HIDE" to hide the
image, press again to display the image.
7
8
9
MEDIA_SETUP No function.
RATIO
ZOOM
To choose the desired aspect ratio.
Zooms the projector display in or out.
To pause the screen image.
10
11
FREEZE
MENU
•
Press "MENU" to launch the Onscreen display (OSD)
menu, back to the previous step for the OSD menu
operation or exit the OSD menu.
•
Confirm your selection of items.
12
13
KEYSTONE
Adjusts the image to compensate for distortion caused by
tilting the projector.
Four
directional
select keys
Use up, down, left, right buttons to select items or make
adjustments to your selection.
7
#
Icon
Function
Description
14
Pre./Rewind
No function.
No function.
Enter/ Play/
Pause
Back/Stop
No function.
No function.
Next/Fast
forward
15
16
KeyPad 0~9
PgUp/PgDn
Press "0~9" to input a password in the "Security" OSD.
For computer mode only. Use this button to select the next or
previous page. This function is only available when USB Ctrl
connector (mini type B) is connected to a computer via a USB
cable.
17
18
19
COMPONENT No function.
VIDEO
VGA
To change source to COMPOSITE VIDEO.
Press "VGA" to change source to the VGA connector. This
connector supports analog RGB, YPbPr (480p/576p/720p/
1080i), YCbCr (480i/576i) and RGBsync.
20
21
22
23
24
S-VIDEO
SD/USB A
USB B
To change source to S-Video.
No function.
For USB control and firmware upgrade.
To change source to HDMI/MHL. (no DVI function)
HDMI/DVI
LAN/WiFi
Press "LAN/WiFi" to display the image which is wire or
wirelessly transmitted from the PC to the projector via the
"Acer LAN webpage management" utility.
Laser pointer Aim the remote at the viewing screen.
25
26
Laser button Aim the remote at the viewing screen, press and hold this
button to activate the laser pointer.
This function is not supported in Japanese market.
Note: Functions vary depending on model definition.
8
MHL (Mobile High-Definition Link) Control
SOURCE
2
1
MEDIA
SETUP
MODE
HIDE
ZOOM
FREEZE
3
4
5
8
6
7
#
Icon Component
MODE
Description
1
•
•
Press "MODE" button for one second to activate the
MHL Control Mode.
To exit, press the "MODE" button again.
2
3
4
SOURCE
MENU
Press the "SOURCE" button to toggle between Navigation
or Numeric mode.
Press to launch the root memu.
(only for Navigation mode)
Direction Keys Use up, down, left, right buttons to select items or make
adjustments to your selection.
(only for Navigation mode)
5
6
7
8
Select
To select the file. (only for Navigation mode)
To exit the file. (only for Navigation mode)
Exit
PgUp/PgDn
KeyPad 0~9
Use the button to select the next or previous
page. (only for Navigation mode)
Number buttons. (only for Numeric mode)
Note: Functions vary depending on model definition.
9
Getting Started
Connecting the Projector
<Type 1>
DVD player,
Set-top Box,
S-Video output
HDTV receiever
D-Sub
5
D-Sub
W
R
DVD player
11
6
8
2
R B G
Video output
2
MHL
USB
12
4
HDTV adapter
D-Sub
Y
W
R
HDMI
HDMI
D-Sub
VGA OUT
VGA IN
2
VGA IN
1
7
S-VIDEO
8
VIDEO
/
MHL
AUDIO IN
USB
AUDIO OUT
AUDIO IN
RS232
USB CTRL
1
8
9
RS232
RS232
3
10
R
W
USB
14
13
Internet
VGA OUT
DC 5V OUT
VIDEO
Smart Phone
1/ MHL
VGA IN
USB CTRL
AUDIO IN
1
LAN
2
AUDIO OUT AUDIO IN
2
RS 232
10
<Type 2>
DVD player, Set-
top Box, HDTV
receiever
5
D-Sub
Video output
DVD player
11
R
B G
4
2
MHL
Y
USB
12
7
HDTV adapter
D-Sub
Y
HDMI
HDMI
1
10
3
USB
#
1
Description
#
8
Description
Audio cable jack/RCA
RS232 cable
Power cord
VGA cable
2
9
3
Audio cable jack/jack
10 USB cable
4
VGA to component/HDTV adapter
3 RCA component cable
S-Video cable
11 HDMI cable
5
12 MHL cable (MicroUSB to HDMI)
13 RJ45 cable
6
7
Composite video cable
14 USB cable for charging device
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: Functions vary depending on model definition.
Note: USB cable needs powered extender if the length is over 5 m.
Note: VGA OUT loops through for VGA IN 2 only.
Note: Some smartphones require a converter (supplied by
smartphone maker) to enable the MHL function.
11
Turning the Projector On/Off
Turning on the Projector
1
2
3
Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
Turn on the projector by pressing "Power" button on the control panel or
remote control, and the Power indicator LED will turn blue.
Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
•
If the screen displays "Lock" and "Source" icons, it means the
projector is locked onto a specific source type and there is no such
type of input signal detected.
•
•
If the screen displays "No Signal", please make sure the signal cables
are securely connected.
If you connect to multiple sources at the same time, use the "Source"
button on either control panel or the remote control or direct source
key on the remote control to switch between inputs.
Power button
12
Turning the projector off
1
To turn the projector off, press and hold the power button. This message
appears: "Please press the power button again to complete the shutdown
process." Press the power button again.
2
The LED power indicator will turn RED and blink rapidly after the projector
is turned off, and the fan(s) will continue to operate for about 2 minutes to
ensure that the system cools properly. (only supported under "Instant
Resume" mode)
3
As long as the power cord remains plugged in, you can press the power
button to turn the projector immediately back on anytime during the 2-
minute shutdown process. (only supported under "Instant Resume" mode)
4
5
Once the system has finished cooling, the LED power indicator will stop
blinking and turn solid red to indicate standby mode.
It is now safe to unplug the power cord.
Warning indicators:
•
•
"Projector Overheated. Lamp will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The lamp with automatically turn off, the projector will automatically
shut down, and the LED temp indicator will turn solid red. Contact
your local dealer or service center.
"Fan failed. Lamp will automatically turn off soon."
This onscreen message indicates that the fan has failed. The lamp will
automatically turn off, the projector will automatically shut down,
and the LED temp indicator will blink. Contact your local dealer or
service center.
Note: Whenever the projector automatically shuts down and the
LED lamp indicator turns solid red, contact your local reseller or
service center.
Note: Functions vary depending on model definition.
14
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen.
•
XGA series
If the projector is 2.0 m from the screen, good image quality is possible for
image sizes between 51" and 62".
Note: Remind as below figure, the space of 108 cm height is
required when located at 2.0 m distance.
62"
B
Height: 108 cm
from base to top
of image
Height:
90 cm
C
A
2.0 m
Desired Distance
Screen size
(Min zoom)
Top
Screen size
(Max zoom)
Top
Desired
Distance
(m)
Diagonal
From base to top Diagonal
of image (cm)
<C>
From base to top
of image (cm)
<C>
W (cm) x H
(cm)
W (cm) x H
(cm)
(inch)
<B>
(inch)
<B>
<A>
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
9.0
10.0
38
51
64
77
90
103
115
128
141
154
167
179
231
256
78 x 59
104 x 78
130 x 98
67
90
46
62
77
94 x 70
125 x 94
81
108
135
162
189
216
243
270
296
323
350
377
485
539
112
135
157
180
202
225
247
270
292
314
404
449
156 x 117
188 x 141
219 x 164
250 x 188
281 x 211
313 x 234
344 x 258
375 x 281
406 x 305
438 x 328
563 x 422
625 x 469
156 x 117
182 x 137
208 x 156
234 x 176
260 x 195
286 x 215
313 x 234
339 x 254
365 x 273
469 x 352
521 x 391
92
108
123
138
154
169
185
200
215
277
308
Zoom Ratio: 1.2x
15
•
WXGA series
If the projector is 2.0 m from the screen, good image quality is possible for
image sizes between 60" and 73".
Note: Remind as below figure, the space of 110 cm height is
required when located at 2.0 m distance.
73"
B
Height: 110 cm
from base to
top of image
Height:
91 cm
C
A
2.0 m
Desired Distance
Screen size
(Min zoom)
Top
Screen size
Top
From base to
top of image
(cm)
Desired
Distance
(m)
(Max zoom)
From base
Diagonal
(inch) W (cm) x H (cm)
<B>
Diagonal
(inch) W (cm) x H (cm)
<B>
to top of
image (cm)
<C>
<A>
<C>
1.5
2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
6.0
6.5
7.0
7.5
8.3
45
98 x 61
69
54
117 x 73
156 x 98
82
60
130 x 81
91
73
110
137
165
192
220
247
274
302
329
357
384
412
456
76
163 x 102
195 x 122
228 x 142
260 x 163
293 x 183
326 x 203
358 x 224
391 x 244
423 x 264
456 x 285
488 x 305
540 x 338
114
137
160
183
206
229
252
274
297
320
343
380
91
195 x 122
234 x 146
273 x 171
313 x 195
352 x 220
391 x 244
430 x 269
469 x 293
508 x 317
547 x 342
586 x 366
648 x 405
91
109
127
145
163
181
199
218
236
254
272
301
106
121
136
151
166
181
196
212
227
251
Zoom Ratio: 1.2x
16
•
1080p series (P5515/N156/PN-805)
If the projector is 3 m from the screen, good image quality is possible for image
sizes between 93" and 127".
Note: Remind as below figure, the space of 183 cm height is
required when located at 3 m distance.
127"
B
93"
Height: 183 cm
from base to top
of image
Height:
13C5 cm
A
3 m
Desired Distance
Screen size
(Min zoom)
From base to
Screen size
(Max zoom)
Top
Top
Desired
Distance
(m)
Diagonal
(inch)
Diagonal
From base to top
of image (cm)
<C>
W (cm) x H top of image
W (cm) x H
(cm)
(inch)
<B>
<A>
(cm)
(cm)
<C>
<B>
1.3
1.5
2
40
47
90 x 50
58
55
122 x 68
140 x 79
70
103 x 58
67
63
92
62
138 x 78
90
85
187 x 105
234 x 132
281 x 158
328 x 184
375 x 211
421 x 237
468 x 263
515 x 290
562 x 316
609 x 342
665 x 374
122
153
183
214
244
275
305
336
367
397
434
2.5
3
78
172 x 97
112
135
157
180
202
225
247
270
292
319
106
127
148
169
190
211
233
254
275
300
93
207 x 116
241 x 136
276 x 155
310 x 174
345 x 194
379 x 213
414 x 233
448 x 252
489 x 275
3.5
4
109
125
140
156
171
187
202
221
4.5
5
5.5
6
6.5
7.1
Zoom Ratio: 1.36x
17
•
1080p series (H6517BD/E145D/HE-801J)
If the projector is 3 m from the screen, good image quality is possible for image
sizes between 84" and 92".
Note: Remind as below figure, the space of 132 cm height is
required when located at 3 m distance.
92"
B
84"
Height: 132 cm
from base to top
of image
Height:
121 cm
C
A
3 m
Desired Distance
Screen size
(Min zoom)
From base to
Screen size
(Max zoom)
Top
Top
Desired
Distance
(m)
Diagonal
(inch)
Diagonal
From base to top
of image (cm)
<C>
W (cm) x H top of image
W (cm) x H
(cm)
(inch)
<B>
<A>
(cm)
(cm)
<C>
<B>
1.5
2
42
56
93 x 52
60
46
61
101 x 57
135 x 76
66
123 x 69
81
88
2.5
3
70
154 x 87
101
121
141
161
181
201
242
282
322
363
403
76
169 x 95
110
132
154
176
198
220
265
309
353
397
441
84
185 x 104
216 x 122
247 x 139
278 x 156
309 x 174
370 x 208
432 x 243
494 x 278
556 x 313
617 x 347
92
203 x 114
236 x 133
270 x 152
304 x 171
338 x 190
405 x 228
473 x 266
541 x 304
608 x 342
676 x 380
3.5
4
98
107
122
137
153
183
214
244
275
305
112
125
139
167
195
223
251
279
4.5
5
6
7
8
9
10
Zoom Ratio: 1.1x
18
•
1080p series (H6517ST/E145S/HE-801ST)
If the projector is 1.5 m from the screen, good image quality is possible for
image sizes 136".
Note: Remind as below figure, the space of 196 cm height is
required when located at 1.50 m distance.
136"
B
Height:
196 cm
C
A
1.50 m
Desired Distance
Screen size
Top
Desired
Distance (m)
<A>
(zoom)
Diagonal
(inch)
<B>
From base to top of
image (cm)
<C>
W (cm) x H (cm)
0.50
0.75
1.00
1.25
1.50
1.75
2.00
2.25
2.50
2.75
3.00
3.25
3.35
45
100 x 56
150 x 85
65
68
98
91
200 x 113
251 x 141
301 x 169
351 x 197
401 x 225
451 x 254
501 x 282
551 x 310
601 x 338
351 x 366
671 x 378
131
163
196
229
262
294
327
360
392
425
438
113
136
158
181
204
226
249
272
294
303
Zoom Ratio: 1.0x
19
How to get a preferred image size by adjusting
distance and zoom
The table below shows how to achieve a desired image size by adjusting either
the position or the zoom ring.
•
XGA series
To obtain an image size of 50" set the projector at a distance 1.6 m and 2.0 m
from the screen.
A
50"
Desired image
size
D
Height: 88 cm
from base to top
of image
1.6 m
B
2.0 m
Desired Distance
C
Desired Image Size
Distance (m)
Top (cm)
From base to top of
Diagonal (inch)
Max zoom
Min zoom
<C>
W (cm) x H (cm)
image
<D>
67
70
88
105
123
140
158
175
210
263
315
438
526
538
<A>
<B>
38
40
50
60
70
80
90
100
120
150
180
250
300
77 x 58
81 x 61
1.2
1.3
1.6
2.0
2.3
2.6
2.9
3.3
3.9
4.9
5.9
8.1
9.8
10.0
1.5
1.6
2.0
2.3
2.7
3.1
3.5
3.9
4.7
5.9
7.0
9.8
11.7
12.0
102 x 76
122 x 91
142 x 107
163 x 122
183 x 137
203 x 152
244 x 183
305 x 229
366 x 274
508 x 381
610 x 457
624 x 468
307
Zoom Ratio: 1.2x
20
•
WXGA series
To obtain an image size of 60" set the projector at a distance 1.7 m and 2.0 m
from the screen.
A
60"
Desired
image size
D
Height: 91 cm
from base to top
of image
1.7 m
B
2.0 m
C
Desired Distance
Desired Image Size
Distance (m)
Top (cm)
From base to top of
Diagonal (inch)
Max zoom
Min zoom
<C>
W (cm) x H (cm)
image
<D>
<A>
<B>
45
97 x 61
108 x 67
118 x 74
129 x 81
151 x 94
172 x 108
194 x 121
215 x 135
258 x 162
323 x 202
431 x 269
538 x 337
646 x 404
1.2
1.4
1.5
1.7
1.9
2.2
2.5
2.8
3.3
4.1
5.5
6.9
8.3
1.5
1.7
1.8
2.0
2.3
2.6
3.0
3.3
4.0
5.0
6.6
8.3
9.9
68
76
50
55
83
60
91
70
106
121
136
151
182
227
303
378
454
80
90
100
120
150
200
250
300
Zoom Ratio: 1.2x
21
•
1080p series (P5515/N156/PN-805)
To obtain an image size of 60" set the projector at a distance 1.4 m and 1.9 m
from the screen.
A
60"
Desired
image size
D
Height: 87 cm
from base to top of
image
1.4 m
B
1.9 m
C
Desired Distance
Desired Image Size
Distance (m)
Top (cm)
From base to top of
Diagonal (inch)
Max zoom
Min zoom
<C>
W (cm) x H (cm)
image
<D>
<A>
<B>
40
89 x 50
0.9
1.2
1.4
1.7
1.9
2.1
2.4
2.8
3.5
4.3
4.7
5.9
7.1
1.3
1.6
1.9
2.2
2.6
2.9
3.2
3.9
4.8
5.8
6.4
8.0
58
50
111 x 62
133 x 75
155 x 87
177 x 100
199 x 112
221 x 125
266 x 149
332 x 187
398 x 224
443 x 249
553 x 311
664 x 374
72
60
87
70
101
116
130
144
173
217
260
289
361
433
80
90
100
120
150
180
200
250
300
Zoom Ratio: 1.36x
22
•
1080p series (H6517BD/E145D/HE-801J)
To obtain an image size of 50" set the projector at a distance 1.6 m and 1.8 m
from the screen.
A
50"
Desired
image size
D
Height: 72 cm
from base to top of
image
1.6 m
B
1.8 m
C
Desired Distance
Desired Image Size
Distance (m)
Top (cm)
From base to top of
Diagonal (inch)
Max zoom
Min zoom
<C>
W (cm) x H (cm)
image
<D>
<A>
<B>
41.8
93 x 52
1.4
1.6
2.0
2.3
2.6
2.9
3.3
3.9
4.9
5.9
6.6
8.2
10.0
1.5
1.8
2.2
2.5
2.9
3.2
3.6
4.3
5.4
6.5
7.2
9.0
60
50
111 x 62
72
60
133 x 75
87
70
155 x 87
101
116
130
144
173
217
260
289
361
441
80
177 x 100
199 x 112
221 x 125
266 x 149
332 x 187
398 x 224
443 x 249
553 x 311
675 x 380
90
100
120
150
180
200
250
305
Zoom Ratio: 1.1x
23
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .
1
2
Turn on the projector by pressing "Power" button on the control pad.
Press the "MENU" button on the remote control to launch the OSD for
projector installation and maintenance.
3
4
The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more .
The Installation menu includes the following options:
•Projection method
•Projection Mode
•Projection Location
•Auto Keystone settings
•Manual Keystone settings
•H. Keystone
•V. Keystone
•LAN/WiFi
•LAN
•LAN IP/Mask
•USB Display
•Language settings
•WirelessHD Dongle Paring
24
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.
5
Push the MENU button anytime to exit the menu and return to the Acer
welcome screen.
Note: Functions vary depending on model definition.
25
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
•
To open the OSD menu, press "MENU" on the remote control or control
panel.
•
When the OSD is displayed, use the
keys to select any item in the
main menu. After selecting the desired main menu item, press
submenu for feature setting.
to enter
•
Use the
keys to select the desired item and adjust the settings by
keys.
using the
•
•
•
Select the next item to be adjusted in the submenu and adjust as described
above.
Press "MENU" on the remote control or control panel, the screen will
return to the main menu.
To exit OSD, press "MENU" on the remote control or control panel. The
OSD menu will close and the projector will automatically save the new
settings.
Main menu
Setting
Sub menu
Note: Some of the following OSD settings may not be available. Please
refer to the actual OSD of your projector.
Note: Functions vary depending on model definition.
26
Color
There are many factory presets optimized for various types of
images.
Display Mode
•
•
•
•
•
•
•
•
•
•
Bright: For brightness optimization.
Presentation: For meeting presentation.
Standard: For common environment.
Video: For playing video in a bright environment.
Game: For game content.
Education: For education environment.
Movie: For brighter and general movie/video/photo playing.
Dark Cinema: For dark movie content.
Sports: For sport picture.
User: Memorize user's settings.
Use this function to choose a proper color according to the wall.
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.
Wall color
Brightness
Adjust the brightness of the image.
•
•
Press
Press
to darken the image.
to lighten the image.
"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
Contrast
•
•
Press
Press
to decrease the contrast.
to increase the contrast.
Adjusts a video image from black and white to fully saturated
color.
Saturation
Tint
•
•
Press
Press
to decrease the amount of color in the image.
to increase the amount of color in the image.
Adjusts the color balance of red and green.
•
•
Press
Press
to increase the amount of green in the image.
to increase the amount of red in the image.
27
Mode
Color
Use this function to choose CT1, CT2 (Native), CT3, User mode.
Temperature
R Gain
Adjusts the red gain for color temperature optimization.
G Gain
Adjusts the green gain for color temperature optimization.
B Gain
Adjusts the blue gain for color temperature optimization.
R Bias
Adjusts the red bias for color temperature optimization.
G Bias
Adjusts the green bias for color temperature optimization.
B Bias
Adjusts the blue bias for color temperature optimization.
Choose "On" to automatically optimize the display of dark movie
scenes enabling them to be shown in incredible detail.
Dynamic Black
Gamma
Effects the representation of dark scenery. With greater gamma
value, dark scenery looks brighter.
Ind. Color Management
Adjusts the red, green, blue, cyan, yellow and magenta colors.
Advanced
Ind. Hue
Adjusts the color balance of red and green.
Ind. Saturation
Adjusts the selected color to be less or more saturated color.
Ind. Gain
Adjusts the selected color's contrast.
Brilliant Color
Produces an expanded on-screen color spectrum that delivers
enhanced color saturation for bright, true-to-life images.
White Peaking
Increases the brightness of whites that are near 100%. (video
sources only)
Film Mode
Sets the image optimized to 24-frame True Film mode.
Noise Reduction
Adjusts signal noise reduction."0" means the noise reduction is off,
">0" increase noise reduction.
Black Extension
This ensures optimum black level for each analog source.
Note: "Saturation" and "Tint" functions are not supported under computer
or HDMI mode.
Note: Functions vary depending on model definition.
28
Image
Projection
•
•
Front-Desktop: The factory default setting.
Rear-Desktop: When you select this function, the projector
reverses the image so you can project from behind a translucent
screen.
•
•
Rear-Ceiling: When you select this function, the projector
reverses and inverts the image at same time. You can project from
behind a translucent screen with ceiling mounted projection.
Front-Ceiling: When you select this function, the projector
inverts the image for ceiling-mounted projection.
Projection Mode
•
•
Front: The factory default setting.
Rear: Reverses the image so you can project from behind a
translucent screen.
Projection Location
•
•
•
Auto: Automatically adjusts projection location of image.
Desktop
Ceiling: Turns the image upside down for ceiling-mounted
projection.
Aspect Ratio
Use this function to choose your desired aspect ratio.
•
•
•
•
•
Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
Full: Resize image to fit full screen by width (1280 pixels) and
height (800 pixels).
4:3: The image will be scaled to fit the screen and displayed using
a 4:3 ratio.
16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
L.Box: Keep original signal aspect ratio and zoom in by 1.333
times.
Auto Keystone
Automatically adjusts vertical image.
Manual Keystone Adjust image distortion caused by tilting projection.
<Note> The Manual Keystone function is unavailable under Auto
Keystone setting to "On".
29
H./V. Keystone
Auto V. Keystone
Automatically adjusts vertical image.
H. Keystone
Press the
or
button to adjust image distortion horizontally
and makes a squarer image.
V. Keystone
Press the
or
button to adjust image distortion vertically and
makes a squarer image.
4 Corner
Correction
Manually adjusts the shape and size of an image that is unevenly
rectangular on all sides. Press "MODE" repeatedly to select the corner
that you wish to adjust. Press four directional selection keys to adjust
the image shape.
<Note> The function is unavailable when H./ V. Keystone is adjusted.
Adjusts the sharpness of the image.
Sharpness
•
•
Press
Press
to decrease the sharpness.
to increase the sharpness.
H. Position
(Horizontal
position)
•
•
Press
Press
to move the image left.
to move the image right.
V. Position
(Vertical position)
•
•
Press
Press
to move the image down.
to move the image up.
Frequency
Tracking
"Frequency" changes the projector's refresh rate to match the
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to
correct it.
HDMI Color Range Adjust the color range of the HDMI image data to correct color display
error.
•
•
•
Auto: Automatically adjust by information from player.
Limited Range: Prosess the input image as limited color range data.
Full Range: Prosess the input image as full color range data.
HDMI Scan Info
Adjust the overscan ratio of the HDMI image on screen.
•
•
•
Auto: Automatically adjust by information from player.
Underscan: Always no overscan on HDMI image.
Overscan: Always keep overscan on HDMI image.
30
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under HDMI or Video mode.
Note: "HDMI Color Range" and "HDMI Scan Info" functions are only
supported under HDMI mode.
Note: Functions vary depending on model definition.
31
Setting
Startup Screen
Use this function to select your desired startup screen. If you
change the setting, the changes will take effect when you exit the
OSD menu.
•
•
Acer: The default startup screen of your Acer projector.
User: Use memorize picture from "Screen Capture" function.
Use this function to customize the startup screen. To capture the
image that you want to use as the startup screen, follow the
instructions below.
Screen Capture
Notice:
Before proceeding with the following steps, make sure that the
"Keystone" is set to the default value 0 and the aspect ratio is set
to 4:3. For details, refer to the "Image" section.
•
Change the "Startup Screen" from the default setting "Acer"
to "User".
•
•
Press "Screen Capture" to customize the startup screen.
A dialog box appears to confirm the action. Choose "Yes" to
use the current image as your customized startup screen. The
capture range is the red rectangular area. Choose "No" to
cancel the screen capture and exit the onscreen display (OSD).
A message appears, stating that the screen capture is in
progress.
When the screen capture is finished, the message disappears
and the original display is shown.
The customized startup screen, as shown below, takes effect
when there is a new input signal or when you restart the
projector.
•
•
•
Source Lock
When Source Lock is turned "Off", the projector will search for
other signals if the current input signal is lost. When Source Lock is
turned "On", it will "lock" the current source channel unless you
press "Source" button on the remote control for the next channel.
Closed Caption
Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is "16:9" or "Auto" .
VGA OUT (Standby) Default is "Off". Choose "On" to enable VGA OUT connection.
WirelessHD Dongle Default is "No". Select "Yes" to do WirelessHD (WiHD) dongle
Paring
pairing.
Reset
•
Press the
button and choose "Yes" to return the
parameters on all menus to the factory default settings.
Security
Security
This projector provides a useful security function for the
administrator to manage usage of the projector .
Press
to change the "Security" setting. If the security function
is enabled, your must enter the "Administrator Password" first
before changing the security settings.
•
Select "On" to enable the security function. The user has to
enter a password to operate the projector. Please refer to the
"User Password" section for details.
•
If "Off" is selected, then the user can turn on the projector
without password.
32
Timeout(Min.)
Once "Security" is activated to "On", the administrator can set
timeout function.
•
Press
or
to select the timeout interval.
•
•
The range is from 10 minute to 990 minutes.
When the time is up, the projector will prompt the user to
enter the password again.
•
•
The factory default setting of "Timeout(Min.)" is "Off".
Once the security function is enabled, the projector will
request user to enter password when switch on the projector .
Both "User Password" and "Administrator Password" can be
accepted for this dialogue.
User Password
•
•
Press
to setup or change the "User Password".
Press number keys to set your password on the remote control
and press "MENU" to confirm.
•
•
Press
to delete character.
Enter the password when you see "Confirm Password"
displayed.
•
•
The password should be between 4 and 8 characters long.
If you select "Request password only when plugging the
power cord in.", the projector will prompt the user to enter
the password every time the power cord is plugged.
•
If you select "Always request password while projector turns
on.", the user has to enter the password every time when the
projector is turned on.
Administrator Password
The "Administrator Password" can be used in both the "Enter
Administrator Password" and "Enter Password" dialog boxes.
•
•
Press
to change the "Administrator Password".
The factory default of "Administrator Password" is "1234".
If you forgot your administrator password, do the following to
retrieve the administrator password:
•
•
An unique 6-digit "Universal Password" which is printed on
the Security Card (please check accessory in the box). This
unique password is the number which will be accepted by
projector anytime no matter what the Administrator
Password is.
If losing this security card and number, please contact with an
Acer service center.
Lock to user startup screen
Default Lock User Startup Screen is "Off". If lock user startup screen
is "On", users cannot change startup screen anymore and avoid
other users change that arbitrarily. Choose "Off" to unlock startup
screen.
LAN/Control
Channel
Control Channel
Default is "RS232". Choose "LAN" to enable LAN connection.
LAN IP/Mask
Identify IP and Mask address.
LAN Reset
Reset LAN function.
33
Note: Functions vary depending on model definition.
Management
ECO Mode
Choose "On" to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
High Altitude
Turn Off Mode
Choose "On" to turn on High Altitude mode. Operate the fans at
full speed continuously to allow for proper high altitude cooling of
the projector.
•
•
Instant Off: Shuts down the projector without fan cooling.
Instant Resume: Resumes the system when the Power button
is pressed again within 2 minutes.
Auto Shutdown
The projector will automatically shutdown when there is no signal
input after the allocated time. (default is 15 minutes)
AC Power On
Choose "On" to power on projector while AC power plug in.
Displays the lamp’s elapsed operating time (in hours).
Lamp Hour Elapse
Lamp Reminding
Activate this function to display a reminder to change the lamp 30
hours before its expected end-of-life.
Lamp Hour Reset
3D Dust Filter
Press the
counter to 0 hours.
button and choose "Yes" to turn the lamp hour
Replacement Reminder
Default of Replacement Reminder is "Off". Select "On" to activate
filter replacement reminder after installing 3D dust filter.
Place
Choose one of three places (indoor, outdoor, and Loess area) based
on actual environment. The default is "indoor".
Filter Hour
Show the filter used hour information. When meeting max time
based on selected place, it will pop up a warning message to ask
for replacing filter.
Filter Reset
Press the
button and choose "Yes" to return the parameter to
the factory default after replacing new 3D dust filter.
Note: Functions vary depending on model definition.
34
Audio
Volume
•
•
Press
Press
to decrease the volume.
to increase the volume.
Mute
•
•
Choose "On" to mute the volume.
Choose "Off" to restore the volume.
Power On/Off Volume Select this function to adjust the notification volume when
turning the projector on/off.
Alarm Volume
Select the function to adjust the volume of any warning
notifications.
Note: Functions vary depending on model definition.
35
3D
3D
Choose "On" to enable DLP 3D function.
•
On: Choose this item while using DLP 3D glasses, 120Hz 3D
capable graphics cards and HQFS format file or DVD with
corresponding SW player.
•
Off: Turn off 3D mode.
3D Format
If the 3D content is not displayed correctly, you can select a 3D
format that suits the 3D content you are viewing and obtain the
best result.
24P 3D
Choose "96Hz" or "144Hz" to compatible with 3D glasses.
3D L/R Invert
If you see a discrete or overlapping image while wearing DLP 3D
glasses, you may need to execute "Invert" to get best match of
left/right image sequence to get the correct image (for DLP 3D).
3D Warning Message Choose "On" to display the 3D warning message.
Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,
- Stereoscopic Player (Trial):
- DDD TriDef Media Player (Trial):
Note: "3D L/R Invert" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
Language
Language
Choose the multilingual OSD menu. Use the
to select your preferred menu language.
or
key
•
Press
to confirm the selection.
36
Acer LAN webpage management
How to login in
Open browser and enter the Server IP address by 192.168.100.10 to find below
homepage of acer LAN webpage management. A password is needed to login
in before using.
Select a user. Administrator is with high authority that can process more
operations such as network setting and alert setting. Default password of
administrator is "admin". And User is with normal authority with default
password by "user". Click Login button to enter into homepage with correct
password.
37
Home
Home page shows connection status and you can find three main functions
listed, Control Panel, Networking Setting and Alert Setting.
Note: Control Panel and Networking Setting are only for Administrator
account.
Control Panel
Enduser can control and adjust projector setting value via this page.
38
Network Setting
Enduser can set IP address, group name and password as wish. After change
network configurations or password, projector will reboot automatically after
press "Apply".
Note: Group Name and projector Name must be less then 32 characters.
Alert Setting
Enduser can send mail with error message right away if projector has problem.
40
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
#
Problem
Solution
1
No image appears
onscreen
•
•
•
Connected as described in the "Getting Started"
section.
Ensure none of the connector pins are bent or
broken.
Check if the projector lamp has been securely
installed. Please refer to the "Replacing the Lamp"
section.
•
Make sure you have removed the lens cap and the
projector is switched on.
2
Partial, scrolling
or incorrectly
displayed image
(for PC (Windows
2000/XP/Vista/
Windows 7/
•
•
Press "RESYNC" on the remote control.
For an incorrectly displayed image:
•
Open "My Computer", open the "Control
Panel", and then double-click the "Display"
icon.
Windows 8))
•
•
Select the "Settings" tab.
Verify that your display resolution setting is
lower than or equal to WUXGA-RB (1920 x
1200).
•
Click the "Advanced Properties" button.
If the problem still appears, change the monitor display
you are using and follow the steps below:
•
•
•
Verify that the resolution setting is lower than
or equal to WUXGA-RB (1920 x 1200).
Click the "Change" button under the
"Monitor" tab.
Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
•
Verify that the resolution setting of the
monitor display is lower than or equal to
WUXGA-RB (1920 x 1200).
41
3
Partial, scrolling
or incorrectly
displayed image
(For notebooks)
•
•
Press "RESYNC" on the remote control.
For an incorrectly displayed image:
•
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
•
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5]
•
•
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
®
®
4
The screen of the
notebook
computer is not
displaying your
presentation
If you are using a Microsoft Windows based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
®
®
•
If you are using an Apple Mac OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On".
5
6
Image is unstable
or flickering
•
•
Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
Change the display color depth settings on your
computer.
Image has vertical
flickering bar
•
•
Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
7
Image is out of
focus
•
•
•
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the
required distance of 4.9 to 32.0 feet (1.5 to 9.8
meters) (XGA series) / 4.9 to 27.1 feet (1.5 to 8.3
meters) (WXGA series) / 1.6 to 10.9 feet (0.5 to 3.3
meters) (1080p, H6517ST/E145S/HE-801ST series) / 4.9
to 32.2 feet (1.5 to 9.8 meters) (1080p, H6517BD/
E145D/HE-801J series) / 4.3 to 23.3 feet (1.3 to 7.1
meters) (1080p, P5515/N156/PN-805 series) from the
projector. Refer to the "How to Get a Preferred
Image Size by Adjusting Distance and Zoom" section
for more information.
42
8
Image is stretched
when displaying a
"widescreen"
DVD title
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
•
If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
•
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
•
If you play an Letterbox (LBX) format DVD title,
please change the format to Letterbox (LBX) in the
projector OSD.
9
Image is too small
or too large
•
•
Adjust the zoom lever on the top of the projector.
Move the projector closer to or further from the
screen.
•
Press "MENU" on the remote control. Go to "Image -
-> Aspect Ratio" and try different settings or press
"RATIO" on the remote control to adjust directly.
10
Image has slanted
sides
•
•
•
If possible, reposition the projector so that it is
centered on the screen.
Press the "Keystone
/
" button on the remote
control until the sides are vertical.
Press "MENU" on the remote control. Go to "Image -
-> Auto Keystone" and choose "Off" on the OSD, if
"Keystone" button is not available on the remote
control.
11
Image is reversed
•
Select "Image --> Projection" on the OSD and adjust
the projection direction.
43
OSD Messages
#
Condition
Message
Message Reminder
1
•
•
Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed
to cool down before it may be used. Please check the
following message.
Please also check the dust filters if they are installed. If the
dust filter is clogged with dust, please clean it. Please refer to
"Cleaning and replacing the dust filter" for details.
•
Replace the lamp - the lamp is about to reach its maximum
lifetime. Prepare to replace it soon.
Problems with the Projector
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
2
Lamp burns out or makes a
popping sound
When the lamp reaches the end of its useful
life, it will burn out and may make a loud
popping sound. If this happens, the projector
will not turn on until the lamp module has
been replaced. To replace the lamp, follow
the procedures in the "Replacing the Lamp"
section.
44
LED & Alarm Definition Listing
LED Messages
Lamp_LED
Red
Temp_LED
Red
Power LED
Message
Red
Blue
--
Input power plug
Flash ON to
OFF 100ms
Flash ON to
OFF 100ms
Flash ON to
OFF 100ms
Standby
--
--
--
--
--
--
ON
--
--
Power button ON
Lamp retry
ON
--
Quick
Flashing
Power off (Cooling state)
--
--
--
--
Quick
Flashing
--
--
Power button OFF
(cooling completed;
standby mode)
ON
Error (thermal failure)
Error (fan lock)
--
--
ON
--
--
ON
ON
Quick
Flashing
Error (lamp breakdown)
Error (color wheel fail)
ON
--
--
--
--
ON
ON
Quick
Flashing
45
Cleaning and replacing the dust filters
Cleaning the dust filters
Clean the dust filters after every 1000 hours of use. If they are note cleaned
periodically, they can become clogged with dust, preventing proper ventilation.
This can cause overheating and damage the projector.
2
1
Follow these steps:
1
Turn the projector off. Wait for the Power LED to stop flashing then
unplug the power cord.
2
3
4
Allow the projector at least 30 mins to cool down.
Pull out the dust filter. (Illustration #1)
To clean the dust filters, use a small vacuum cleaner designed for
computers and other office equipment. (Illustration #2)
If the dirt is difficult to remove or the filter is broken, please contact your
local dealer or service center to obtain a new filter.
5
46
Replacing the Lamp
Use a screwdriver to remove the screw(s) from the cover, and then pull out the
lamp.
The projector will detect the lamp life. You will be shown a warning message
"Lamp is approaching the end of its useful life in full power operation.
Replacement suggested!" When you see this message, change the lamp as soon
as possible. Make sure the projector has been cooling down for at least 30
minutes before changing the lamp.
Warning: The lamp compartment is hot! Allow it to cool down
before changing the lamp.
2
1
3
4
6
5
To Change the Lamp
Turn off the projector by pressing the Power button.
Allow the projector at least 30 minutes to cool down.
Disconnect the power cord.
1
Use a screwdriver to remove the screw from the cover. (Illustration #1)
Push up and remove the cover. (Illustration #2)
Remove the screw that secure the lamp module. (Illustration #3)
Pull out the lamp plug. (Illustration #4)
2
Lift the handle so that it stands up. (Illustration #5)
Lift the handle so that it stands up. Pull out the lamp module by force.
(Illustration #6)
3
To replace the lamp module, use a new lamp and reverse the above steps.
Warning: To reduce the risk of personal injury, do not drop the
lamp module or touch the lamp bulb. The bulb may shatter and
cause injury if it is dropped.
47
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
1
Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
2
Secure the ceiling rod using the appropriate type of four-cylinder screws.
Ceiling Mount Base
- Attach to ceiling
Short Rod
Long Rod
Extension Rod
Long Cylinder Cap
Allen Key
Screw Type A
- For tightening/loosening
50 mm length / 8 mm diameter
-
Tightening Screw
Medium Rod
48
3
Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Screw Type B
Smaller Washer
Large Washer
Projector Bracket
Supports projector and
-
allows for adjustments
Spacer
- For heat dissipation
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4
Attach the ceiling bracket to the ceiling rod.
Large cylinder cap
Allen Key
- For tightening/loosening
Screw Type A
Tightening Screw
50 mm length/
8 mm diameter
-
49
5
Adjust the angle and positioning as necessary.
Tightening Screw
Allen Key
Allen Key
Tightening Screw
Note: The appropriate type of screw and washer for each model is
listed in the table below. 4 mm diameter screws are enclosed in
the screw pack.
Screw Type B
Washer Type
Diameter (mm)
4
Length (mm)
25
Large
V
Small
V
SCREW SPEC. M4 x 25 mm
55.00 mm
85.00 mm
50
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.
®
Projection system
Resolution
DLP
•
•
•
P1287/M416/PE-X45 series: Native 1024 x 768 XGA
resolution
P1387W/M426/PE-W45 series: Native 1280 x 800
WXGA resolution
P5515/N156/PN-805/H6517BD/E145D/HE-801J/
H6517ST/E145S/HE-801ST series: 1920x1080 1080p
resolution
•
Maximum: UXGA (1600 x 1200), WSXGA+
(1680x1050), 1080p(1920x1080), WUXGA-RB (1920
x 1200)
Computer compatibility
Video compatibility
IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, VGA, SVGA, SXGA+,
WXGA, WXGA+, WSXGA +
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)
Aspect ratio
Full, 4:3, 16:9, L.Box
16.7 million colors
Displayable colors
Projection lens
•
P1287/M416/PE-X45/P1387W/M426/PE-W45 series:
f = 2.41 ~ 2.70, f = 18.17 mm ~ 21.81 mm, 1.2x
manual zoom and manual focus
•
•
H6517ST/E145S/HE-801ST series: F = 2.80,
f = 7.42 mm, 1.0x manual zoom and manual focus
H6517BD/E145D/HE-801J series: F = 2.5 ~ 2.67,
f = 21.90mm ~ 24.00mm, 1:1.1 Manual Zoom and
Manual Focus
•
P5515/N156/PN-805 series: F = 2.5 ~ 2.93,
f = 15.98mm ~ 21.42mm, 1:1.4 Manual Zoom and
Manual Focus
Projection screen size (diagonal)
•
•
•
•
P1287/M416/PE-X45 series:
38" (98 cm) ~ 300" (762 cm)
P1387W/M426/PE-W45/H6517ST/E145S/HE-801ST
series: 45" (115cm) ~ 300" (762cm)
H6517BD/E145D/HE-801J series:
42" (106cm) ~ 300" (762cm)
P5515/N156/PN-805 series:
40" (103cm) ~ 300" (762cm)
51
Projection distance
•
•
•
•
P1287/M416/PE-X45 series:
4.9' (1.5 m) ~ 32.0' (9.8 m)
P1387W/M426/PE-W45 series:
4.9' (1.5m) ~ 27.1' (8.3m)
H6517ST/E145S/HE-801ST series:
1.6' (0.5m) ~ 10.9' (3.3m)
H6517BD/E145D/HE-801J series:
4.9' (1.5m) ~ 32.2' (9.8m)
•
•
•
P5515/N156/PN-805 series: 4.3' (1.3m) ~ 23.3' (7.1m)
P1287/M416/PE-X45 series: 62"@2m (1.60 ~ 1.92:1)
Throw ratio
P1387W/M426/PE-W45 series:
73"@2m (1.28 ~ 1.54:1)
•
•
•
H6517ST/E145S/HE-801ST series:
181"@2m (0.50 ~ 0.50:1)
H6517BD/E145D/HE-801J series:
61"@2m (1.48 ~ 1.62:1)
P5515/N156/PN-805 series: 85"@2m (1.07 ~ 1.45:1)
Horizontal scan rate
Vertical refresh scan rate
Lamp type
15 - 100 kHz
24 - 120 Hz
•
•
•
P1287/M416/PE-X45/P1387W/M426/PE-W45/P5515/
N156/PN-805 series: 260 W user-replaceable lamp
H6517ST/E145S/HE-801ST/H6517BD/E145D/HE-801J
series: 210W user-replaceable lamp
Keystone correction
Audio
P1287/M416/PE-X45/P1387W/M426/PE-W45/
H6517ST/E145S/HE-801ST/H6517BD/E145D/HE-801J
series: ±40 degrees
•
•
P5515/N156/PN-805 series: ±30 degrees
P1287/M416/PE-X45/P1387W/M426/PE-W45/P5515/
N156/PN-805 series: Internal speaker with 10 W
output
•
H6517ST/E145S/HE-801ST/H6517BD/E145D/HE-801J
series: Internal speaker with 2 W output
Weight
2.5 ~ 3.0 Kg (5.51 ~ 6.61 Ibs)
Dimensions (W x D x H)
Digital Zoom
314 mm X 223.4 mm X 93.4 mm (12.4" x 8.8" x 3.7")
2X
Power supply
AC input 100 - 240 V auto-switching power supply
Power consumption
•
P1287/M416/PE-X45/P1387W/M426/PE-W45 series:
Normal mode: 330W ± 10% @ 110VAC
ECO mode: 280W ± 10% @ 110VAC
Standby mode < 0.5W
•
H6517ST/E145S/HE-801ST/H6517BD/E145D/HE-801J
series:
Normal mode: 255W ± 10% @ 110VAC
ECO mode: 196W ± 10% @ 110VAC
Standby mode: < 0.5W
•
P5515/N156/PN-805 series:
Normal mode: 325W ± 10% @ 110VAC
ECO mode: 270W ± 10% @ 110VAC
Standby mode < 0.5W
Network standby mode: <3W
52
Operating temperature
0ºC to 40ºC / 32ºF to 104ºF
Standard package contents
•
•
•
•
•
•
•
•
AC power cord x1
VGA cable x1
Remote control x1
Battery x2 (for remote control) (option)
User's guide (CD-ROM) x1
Quick start guide x1
Security card x1
Carrying case x1 (option)
P1287/ M416/PE-X45/
P1387W/ M426/PE-W45
P5515/N156/
PN-805
H6517BD/E145D/HE-801J/
H6517ST/E145S/HE-801ST
I/O connectors
Power socket
DC Jack
V
X
X
V
V
V
V
V
V
X
X
V
V
X
V
X
X
X
VGA IN
VGA IN 1
VGA IN 2
VGA output
3.5 mm audio jack
input 1
V
V
V
S-Video
V
V
X
V
X
V
Composite video
3.5 mm audio jack
input 2
V
V
V
V
X
X
3.5 mm audio jack
output
RJ45 LAN input
RS232
X
V
V
X
V
V
V
V
X
X
V
V
HDMI /MHL
HDMI
Mini USB x1 (for
firmware
V
V
V
upgrade)
Note: Design and specifications are subject to change without
notice.
53
Compatibility modes
A. VGA Analog
1
VGA Analog - PC Signal
Modes
VGA
Resolution
V.Frequency [Hz] H.Frequency [KHz]
640x480
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
60
72
31.5
37.9
37.5
43.3
61.9
35.1
37.9
48.1
46.9
53.7
77.4
48.4
56.5
60.0
68.7
99.0
63.8
67.5
77.1
64.0
77.0
80.0
91.1
60.0
75.2
65.3
75.0
31.4
34.9
37.9
48.4
68.7
75.0
60.0
75
85
120
56
60
72
75
85
120
60
SVGA
800x600
800x600
XGA
1024x768
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
70
75
85
120
70
75
85
60
72
SXGA
75
85
60
75
60
60
60
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
i Mac DV (G3)
640x480
800x600
1024x768
1152x870
1280x960
1024x768
66.6(67)
60
60
75
75
75
54
2
VGA Analog - Extended Wide timing
Modes
WXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
1280x800-RB
*1920x1200
1440x900
1680x1050
1920x1080
(1080P)
1366x768
1920x1200-RB
V.Frequency [Hz] H.Frequency [KHz]
60
75
85
60
120
60
47.8
60.3
68.6
44.8
92.9
49.6
101.6
74
119.909
60
60
60
59.9
65.3
WSXGA+
WUXGA
60
67.5
60
47.7
59.94
74.04
3
VGA Analog -Component Signal
Modes
Resolution
V.Frequency [Hz] H.Frequency [KHz]
480i
576i
480p
576p
720p
720x480(1440x480)
720x576(1440x576)
720x480
59.94 (29.97)
50(25)
59.94
50
60
50
60(30)
50(25)
23.97/24
60
15.7
15.6
31.5
31.6
45.0
37.5
33.8
28.1
27.0
67.5
56.3
74.04
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1200
720p
1080i
1080i
1080p
1080p
1080p
*1080p
50
59.94
B. HDMI Digital
1
HDMI - PC Signal
Modes
VGA
Resolution
640x480
640x480
640x480
V.Frequency [Hz] H.Frequency [KHz]
60
72
75
31.5
37.9
37.5
55
640x480
640x480
800x600
800x600
800x600
800x600
800x600
800x600
1024x768
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
1600x1200
640x480
85
120
56
60
72
75
85
120
60
70
75
85
120
70
75
85
60
72
75
43.3
61.9
35.1
37.9
48.1
46.9
53.7
77.4
48.4
56.5
60.0
68.7
99.0
63.8
67.5
77.1
64.0
77.0
80.0
91.1
60.0
75.2
65.3
75.0
31.4
34.9
37.9
48.4
68.7
75.0
60.0
SVGA
XGA
SXGA
85
60
75
60
60
60
QuadVGA
SXGA+
UXGA
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
i Mac DV (G3)
640x480
800x600
1024x768
1152x870
1280x960
1024x768
66.6(67)
60
60
75
75
75
2
HDMI - Extended Wide timing
Modes
WXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x720
1280x800
1280x800-RB
V.Frequency [Hz] H.Frequency [KHz]
60
75
47.8
60.3
68.6
44.8
92.9
49.6
101.6
85
60
120
60
119.909
56
1440x900
*1920x1200
1680x1050
1920x1080
(1080P)
60
60
60
59.9
74
65.3
WSXGA+
WUXGA
60
67.5
1366x768
1920x1200-RB
60
59.94
47.7
74.04
3
HDMI - Video Signal
Modes
Resolution
V.Frequency [Hz] H.Frequency [KHz]
480i
576i
480p
576p
720p
720x480(1440x480)
720x576(1440x576)
720x480
59.94 (29.97)
50(25)
59.94
50
60
50
60(30)
50(25)
23.97/24
60
15.7
15.6
31.5
31.6
45.0
37.5
33.8
28.1
27.0
67.5
56.3
74.04
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
1920x1080
1920x1200
720p
1080i
1080i
1080p
1080p
1080p
*1080p
50
59.94
4
HDMI - 1.4a 3D Timing
Modes
Resolution
V.Frequency [Hz] H.Frequency [KHz]
720p (Frame Packing)
720p (Frame Packing)
1080p (Frame Packing ) 1920 x1080
720p (Frame Packing)
720p (Frame Packing)
1080i (Top and Bottom) 1920 x1080
1080i (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
1080p (Top and Bottom) 1920 x1080
720p (Side by Side (Half)) 1280 x 720
1080i (Side by Side (Half)) 1920 x1080
1080i (Side by Side (Half)) 1920 x1080
1080p (Side by Side (Half)) 1920 x1080
1280 x 720
1280 x 720
50
60
24
50
60
50 (25)
60 (30)
24
50
60
37.5
45.0
27.0
37.5
45.0
28.1
33.8
27.0
56.3
67.5
45.0
28.1
33.8
56.3
1280 x 720
1280 x 720
60
50 (25)
60 (30)
50
57
1080p (Side by Side (Half)) 1920 x1080
60
67.5
15k-100kHz
24-120 Hz
165 MHz
Horizontal scan rate:
Vertical scan rate:
Max. pixel rate:
Graphic source monitor
range limits
C. MHL Digital
V.Frequency
H.Frequency
[KHz]
31.5
Modes
Resolution
[Hz]
59.94/60
59.94/60
50(25)
59.94/60
59.94/60
50
VGA
480i
576i
480p
480p_2x
576p
640x480
720x480 (1440x480)
720x576 (1440x576)
720x480
15.7
15.6
31.5
31.5
1440x480
720x576
31.3
576p_2x
720p
720p
1440x576
1280x720
1280x720
50
59.94/60
50
31.3
45.0
37.5
1080i
1080i
1080p
1080p
1080p
1920x1080
1920x1080
1920x1080
1920x1080
60(30)
50(25)
23.97/24
25
33.8
28.1
27.0
28.1
1920x1080
29.97/30
33.8
Horizontal scan rate:
15k-50 kHz
Graphic source monitor
range limits
Vertical scan rate:
Max. pixel rate:
24-60 Hz
Digital: 75 MHz
Note: * Functions vary depending on model definition.
58
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
59
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
001
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a
Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b
Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
Declaration of ConformityNew Taipei City 221, Taiwan
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail: [email protected]
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
Declare under our own responsibility that the product:
Product:
DLP Projector
Trade Name:
Model Number:
Acer
DNX1403/DWX1425/D1P1404/D1P1426/D1P1427
P1287/M416/PE-X45/P1387W/M426/PE-W45/P5515/
N156/PN-805/H6517BD/E145D/HE-801J/H6517ST/
E145S/HE-801ST
To which this declaration refers conforms to the relevant standard or other standardizing documents:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
EN55022:2010 Class B; EN 55024:2010
EN61000-3-2:2006+A1:2009+A2:2009, Class A
EN61000-3-3:2008
EN 60950-1:2006/A11:2009/A1:2010+A12:2011
Regulation (EC) No. 1275/ 2008; EN 62301:2005
EN50581:2012
We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC and RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2014.
_______________________________
RU Jan / Sr. Manager
Nor. 14, 2014
Date
Regulation, Acer Inc.
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product:
DLP Projector
Model Number:
Machine Type:
DNX1403/DWX1425/D1P1404/D1P1426/D1P1427
P1287/M416/PE-X45/P1387W/M426/PE-W45/
P5515/N156/PN-805/H6517BD/E145D/HE-801J/
H6517ST/E145S/HE-801ST
Name of Responsible Party:
Acer America Corporation
Address of Responsible Party: 333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
|