Acer Projector
K335/L320/LK-W20 Series
User's Guide
iii
Information for your safety and
comfort
Read these instructions carefully. Keep this document for future reference.
Follow all warnings and instructions marked on the product.
Turning the product off before cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Caution for plug as disconnecting device
Observe the following guidelines when connecting and disconnecting power to
the external power supply unit:
•
•
•
Install the power supply unit before connecting the power cord to the AC
power outlet.
Unplug the power cord before removing the power supply unit from the
projector.
If the system has multiple sources of power, disconnect power from the
system by unplugging all power cords from the power supplies.
Caution for Accessibility
Be sure that the power outlet you plug the power cord into is easily accessible
and located as close to the equipment operator as possible. When you need to
disconnect power to the equipment, be sure to unplug the power cord from the
electrical outlet.
Warnings!
•
•
Do not use this product near water.
Do not place this product on an unstable cart, stand or table. If the product
falls, it could be seriously damaged.
•
Slots and openings are provided for ventilation to ensure reliable
operation of the product and to protect it from overheating. These
openings must not be blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug or other similar surface.
This product should never be placed near or over a radiator or heat register, or
in a built-in installation unless proper ventilation is provided.
•
Never push objects of any kind into this product through cabinet slots as
they may touch dangerous voltage points or short-out parts that could
result in a fire or electric shock. Never spill liquid of any kind onto or into
the product.
iv
•
•
To avoid damage of internal components and to prevent battery leakage,
do not place the product on a vibrating surface.
Never use it under sporting, exercising, or any vibrating environment
which will probably cause unexpected short current or damage rotor
devices.
Using electrical power
•
This product should be operated from the type of power indicated on the
marking label. If you are not sure of the type of power available, consult
your dealer or local power company.
•
•
Do not allow anything to rest on the power cord. Do not locate this
product where people will walk on the cord.
If an extension cord is used with this product, make sure that the total
ampere rating of the equipment plugged into the extension cord does not
exceed the extension cord ampere rating. Also, make sure that the total
rating of all products plugged into the wall outlet does not exceed the fuse
rating.
•
•
Do not overload a power outlet, strip or receptacle by plugging in too
many devices. The overall system load must not exceed 80% of the branch
circuit rating. If power strips are used, the load should not exceed 80% of
the power strip's input rating.
This product's AC adapter is equipped with a three-wire grounded plug.
The plug only fits in a grounded power outlet. Make sure the power outlet
is properly grounded before inserting the AC adapter plug. Do not insert
the plug into a non-grounded power outlet. Contact your electrician for
details.
Warning! The grounding pin is a safety feature. Using a power outlet that is
not properly grounded may result in electric shock and/or injury.
Note: The grounding pin also provides good protection from unexpected
noise produced by other nearby electrical devices that may interfere with
the performance of this product.
•
Use the product only with the supplied power supply cord set. If you need
to replace the power cord set, make sure that the new power cord meets
the following requirements: detachable type, UL listed/CSA certified, VDE
approved or its equivalent, 4.5 meters (15 feet) maximum length.
v
Product servicing
Do not attempt to service this product yourself, as opening or removing covers
may expose you to dangerous voltage points or other risks. Refer all servicing to
qualified service personnel.
Unplug this product from the wall outlet and refer servicing to qualified service
personnel when:
•
•
•
•
•
the power cord or plug is damaged, cut or frayed
liquid was spilled into the product
the product was exposed to rain or water
the product has been dropped or the case has been damaged
the product exhibits a distinct change in performance, indicating a need
for service
•
the product does not operate normally after following the operating
instructions
Note: Adjust only those controls that are covered by the operating
instructions, since improper adjustment of other controls may result in
damage and will often require extensive work by a qualified technician to
restore the product to normal condition.
Warning! For safety reasons, do not use non-compliant parts when adding
or changing components. Consult your reseller for purchase options.
Your device and its enhancements may contain small parts. Keep them out of
the reach of small children.
Additional safety information
•
Do not look into the projector's lens when the light is on. The bright may
hurt your eyes.
•
•
Turn on the projector first and then signal sources
Do not place the product in following environments:
•
•
•
Space that is poorly ventilated or confined. At least 50cm clearance from walls
and free flow of air around the projector is necessary.
Locations where temperatures may become excessively high, such as inside of a
car with all windows rolled up.
Locations where excessive humidity, dust, or cigarette smoke may contaminate
optical components, shortening the life span and darkening the image.
•
•
•
Locations near fire alarms.
Locations with an ambient temperature above 40 ºC/104 ºF.
Locations where the altitudes are higher than 10000 feet.
•
Unplug immediately if there is something wrong with your projector. Do
not operate if smoke, strange noise or odor comes out of your projector. It
vi
might cause fire or electric shock. In this case, unplug immediately and
contact your dealer.
•
Do not keep using this product to break or drop it. In this case contact your
dealer for inspection.
•
•
Do not face the projector lens to the sun. It can lead to fire.
When switching the projector off, suggest to ensure the projector
completes its cooling cycle before disconnecting power.
•
Do not frequently turn off the main power abruptly or unplug the
projector during operation. The best way is to wait for the fan to turn off
before turning main power off.
•
•
Do not touch air outlet grille and bottom plate which becomes hot.
Clean the air filter frequently if have. The temperature inside may rise and
cause damage when the filter/ventilation slots clogged with dirt or dust.
•
•
•
Do not look into the air outlet grille when projector is operating. It may
hurt your eyes.
Always open the lens shutter or remove the lens cap when the projector is
on.
Do not block the projector lens with any object when the projector is
under operation as this could cause the object to become heated and
deformed or even cause a fire.
•
•
Do not attempt to disassemble this projector. There are dangerous high
voltages inside which may hurt you. Refer servicing only to suitable
qualified professional service personnel.
Do not stand the projector on end vertically. It may cause the projector to
fall over, causing injury or damage.
Caution for Listening
To protect your hearing, follow these instructions.
•
•
•
•
•
Increase the volume gradually until you can hear clearly and comfortably.
Do not increase the volume level after your ears have adjusted.
Do not listen to music at high volumes for extended periods.
Do not increase the volume to block out noisy surroundings.
Decrease the volume if you can't hear people speaking near you.
vii
Disposal instructions
Do not throw this electronic device into the trash when discarding. To minimize
pollution and ensure utmost protection of the global environment, please
recycle. For more information on the Waste from Electrical and Electronics
Equipment (WEEE) regulations, visit
viii
First things first
Usage Notes
Do:
•
•
Turn off the product before cleaning.
Use a soft cloth moistened with mild detergent to clean the display
housing.
•
Disconnect the power plug from AC outlet if the product is not being used
for a long period of time.
Don't:
•
•
•
Block the slots and openings on the unit provided for ventilation.
Use abrasive cleaners, waxes or solvents to clean the unit.
Use under the following conditions:
•
•
•
•
In extremely hot, cold or humid environments.
In areas susceptible to excessive dust and dirt.
Near any appliance that generates a strong magnetic field.
Place In direct sunlight.
Precautions
Follow all warnings, precautions and maintenance as recommended in this
user's guide to maximize the life of your unit.
Warning:
•
•
Do not look into the projector's lens when the light is on. The bright may hurt your
eyes.
To reduce the risk of fire or electric shock, do not expose this product to rain or
moisture.
•
•
Please do not open or disassemble the product as this may cause electric shock.
When switching the projector off, please ensure the projector completes its cooling
cycle before disconnecting power.
•
•
Turn on the projector first and then the signal sources.
Do not use lens cap when projector is in operation.
Information for your safety and comfort
First things first
Usage Notes
Precautions
Introduction
Product Features
1
Package Overview
Projector Overview
Projector Outlook
Control Panel
Remote Control Layout
Getting Started
Connecting the Projector
12
Turning the Projector On/Off
Turning on the Projector
Adjusting the Height of Projected Image
User Controls
19
21
21
22
22
23
Installation menu
Color
Image
Setting
Management
Audio
3D
Language
Appendices
24
Troubleshooting
24
LED & Alarm Definition Listing
Ceiling Mount Installation
Specifications
28
29
32
34
Compatibility modes
Regulations and safety notices
38
1
Introduction
Product Features
This product is a single-chip DLP® projector. Outstanding features include:
•
•
DLP® technology
1280 x 800 WXGA resolution
Auto, Full, 4:3, 16:9, L.Box aspect ratio supported.
•
•
•
•
Versatile display modes (Bright, Standard, Movie, Dark Cinema, Game,
Sports, User) enable optimum performance in any situation.
NTSC/PAL/SECAM compatible and HDTV (480i/p, 576i/p, 720p, 1080i/p)
supported.
Compact size projector facilitates business purposes and home
entertainment.
Acer EcoProjeciton Technology delivers Intelligent power management
approach and physical efficiency improvement.
•
•
•
•
•
Equipped with HDMITM connection supporting HDCP.
Advanced digital keystone correction delivers optimum presentations.
Multi-language on screen display (OSD) menus.
Environmental light source and longer life by LED solution.
Enjoy media playback via USB, RAM and SD card reader.
•
Microsoft® Windows® 2000, XP, Vista® Windows® 7, Windows® 8,
Macintosh® OS compliant.
•
Support MHL V1.2 signal display.
2
Package Overview
This projector comes with all the items shown below. Check to make sure your
unit is complete. Contact your dealer immediately if any thing is missing.
R
E
N T E
B
A C K
Projector
2 x Batteries
Carrying case
Power cord
Composite video cable
HIDE
ZOOM
MODE
INFO
RATIO
A/a
SOURCE
MENU
MEDIA
BACK
PgUp
PgDn
HOME
SETUP
ENTER
VGA cable
Remote control
K335/
L320/
LK-W20
Series
P/N:MC.JG711.003
User's guide
Quick start guide
P/N:MC.JG711.005
Mutimedia Quick Start Guide
USB WiFi adapter
(option)
Quick start guide
(for multi-media and
wireless functions)
User's guide
(for multi-media and
wireless functions)
3
Projector Overview
Projector Outlook
Front / upper side
6
3
5
R
E
E N T
K
C
B A
4
3
2
1
#
Description
#
Description
1
4
Zoom Lens
Focus ring
2
3
5
6
Tilt adjusting wheel
Power button
Control panel
Remote control receivers
Rear side
3
5
7
8
1
2
4
6
USB
A
USB
B
(MHL)
VGA!IN!
VIDEO OUT AUDIO IN
10
9
#
Description
#
Description
1
2
3
4
SD Card reader
6
7
8
9
Composite video input connector
Audio output connector
Audio input connector
Power socket
USB A connector (for multimedia)
Mini USB
HDMI connector
PC analog signal/HDTV/component
video input connector
5
10
Kensington™ lock port
4
Control Panel
9
2
3
8
5
BACK
ENTER
4
10
7
6
9
1
#
Icon
Function
POWER
Description
1
Power button and Power Indicator LED.
See the contents in "Turning the Projector
On/Off" section.
2
3
4
LAMP
Lamp Indicator LED.
Temp Indicator LED.
TEMP
Back/Stop
Stop playing media file or go back to upper
data folder.
BACK
ENTER
5
6
Enter/ Play/Pause
MENU
Confirm your selection of items or play/
pause media file.
•
Press "MENU" to launch the Onscreen
display (OSD) menu, back to the
previous step for the OSD menu
operation or exit the OSD menu.
7
8
SOURCE
Changes the active source.
Remote control
receiver
Receives signals from remote control.
9
Keystone
Adjusts the image to compensate for
distortion caused by tilting the projector (±
40 degrees).
10
Four directional select Use the keys to select items or make
keys adjustments to your selection.
5
Remote Control Layout
1
2
4
3
HIDE
ZOOM
MODE
INFO
A/a
5
7
6
RATIO
8
SOURCE
10
9
11
12
13
14
MENU
16
18
15
17
19
MEDIA
BACK
PgUp
PgDn
HOME
SETUP
ENTER
Model No:E-26131
20
21
22
24
23
25
MC.JG711.001
#
Icon
Function
Description
1
2
3
Infrared
transmitter
Sends signals to the projector.
HIDE
Momentarily turns off the video. Press "HIDE" to hide the
image, press again to display the image.
POWER
Refer to the "Turning the Projector On/Off" section.
4
5
6
7
8
9
INFO
To display the projector information.
To choose the desired aspect ratio (Auto, 4:3, 16:9, L.Box).
Press “A/a” to select subtitle.
RATIO
A/a
ZOOM
MODE
Zooms the projector display in or out.
Press “MODE” to select display mode.
Press "3D" to select 3D models.
3D
10
11
SOURCE
MENU
Changes the active source.
•
Press "MENU" to launch the Onscreen display (OSD)
menu, back to the previous step for the OSD menu
operation or exit the OSD menu.
•
Confirm your selection of items.
12
KEYSTONE
Adjusts the image to compensate for distortion caused by
tilting the projector (± 40 degrees).
6
#
Icon
Function
Description
13
Four
directional
select keys
Use up, down, left, right buttons to select items or make
adjustments to your selection.
14
15
16
17
18
19
VOLUME
HOME
SETUP
Decreases / Increases the volume.
Press to return to the Home page of Media mode.
Press to enter media OSD setting.
BACK
Press to go back to the previous screen.
Press to play media file or confirm the setting.
Press to rewind the media file.
ENTER
Rewind
20
21
22
Play/Pause
Toggles between playback and pause.
Press to fast forward the media file.
Fast forward
PgUp/PgDn
For computer mode only. Use this button to select the next or
previous page. This function is only available when USB Ctrl
connector(USB type B) is connected to a computer via a USB
cable.
23
24
25
Next
Press to the next media file.
Press to previous the media file.
Discontinues playback.
Previous
Stop
7
MHL (Mobile High-Definition Link) Control
HIDE
ZOOM
MODE
INFO
RATIO
A/a
MHL Control Mode
1
2
Navigation
SOURCE
MHL Control Mode
Exit MHL Control
MHL Control Mode
Multi-Media
4
5
MHL Control Mode
Exit MHL Control
3
6
MENU
MEDIA
7
9
8
10
BACK
PgUp
PgDn
HOME
SETUP
ENTER
11
12
13
#
Icon Component
Description
1
2
MODE
•
•
Press "MODE" button for one second to activate the
MHL Control Mode.
To exit, press the "MODE" button again.
MODE
SOURCE
MENU
Press the "SOURCE" button to toggle between Navigation
or Multi-Media mode.
3
4
Press to launch the root menu. (only for Navigation mode)
MENU
Direction Keys Use up, down, left, right buttons to select items or make
adjustments to your selection. (only for Navigation mode)
5
6
Volume Down Decreases the volume. (only for Multi-Media mode)
Volume Up
Increases the volume. (only for Multi-Media mode)
7
8
9
Exit
To exit the file. (only for Navigation mode)
To enter the file. (only for Navigation mode)
BACK
ENTER
Enter
Backward
Scans backward during the file playback. (only for Multi-
Media mode)
10
11
Play/Pause
Forward
Toggles between playback and pause. (only for Multi-
Media mode)
Scans forward through the file playback. (only for Multi-
Media mode)
8
#
12
Icon Component
PgUp/PgDn
Description
Use the button to select the next or previous page. (only
for Navigation mode)
PgUp
PgDn
13
Stop
Discontinues playback. (only for Multi-Media mode)
9
Getting Started
Connecting the Projector
Video Output
USB
D-Sub
Y
8
9
7
6
10
2
SD CARD
D-Sub
Y
USB A
USB B
(MHL)
VIDEO OUT AUDIO IN
VGA!IN!
HDTV adapter
HDMI
3
9
5
R
B G
1
DVD player,
Set-top Box,
HDTV receiver
HDMI
4
DVD player
R
W
#
Description
#
Description
1 Power cord
6 SD card
USB disk/stick
USB WiFi adapter
(*)
2 VGA cable
7
3 VGA to component/HDTV adapter
4 3 RCA component cable
5 HDMI cable
8 Composite video cable
9 Audio cable Jack/RCA
10 USB cable
Note: To ensure the projector works well with your computer,
please make sure the timing of the display mode is compatible
with the projector.
Note: USB cable needs powered extender if the length is over 5 m.
10
Turning the Projector On/Off
Turning on the Projector
1
2
3
Ensure that the power cord and signal cable are securely connected. The
Power indicator LED will flash red.
Turn on the projector by pressing "Power" button on the control panel,
and the Power indicator LED will turn blue.(Illustration #2)
Turn on your source (computer, notebook, video player ,etc.). The
projector will detect your source automatically.
•
If the screen displays "No Signal", please make sure the signal cables
are securely connected.
•
If you connect to multiple sources at the same time, use the "Source"
button on either control panel or the remote control or direct source
key on the remote control to switch between inputs.
Power button
R
E
N T
E
B A C K
11
Turning the projector off
1
To turn the projector off, press the power button. This message appears:
"Please press the power button again to complete the shutdown process."
Press the power button again.
2
The LED power indicator will turn RED and blink rapidly after the projector
is turned off, and the fan(s) will continue to operate for about 30 sec to
ensure that the system cools properly.
3
4
Once the system has finished cooling, the LED power indicator will stop
blinking and turn solid red to indicate standby mode.
It is now safe to unplug the power cord.
Warning indicators:
•
•
"Projector Overheated. Will automatically turn off soon."
This onscreen message indicates that the projector has overheated.
The projector will automatically shut down. Contact your local dealer
or service center.
"Fan failed. Will automatically turn off soon."
This onscreen message indicates that the fan has failed. The projector
will automatically shut down. Contact your local dealer or service
center.
Note: Whenever the projector automatically shuts down, contact
your local reseller or service center.
13
How to optimize image size and distance
Consult the table below to find the optimal image sizes achievable when the
projector is positioned at a desired distance from the screen. Example: If the
projector is 1.5 m from the screen, good image quality is possible for image sizes
49.7".
Note: Remind as below figure, the space of 70 cm height is
required when located at 1.5 m distance.
screen size
49.7"
Height:
70cm
C
A
1.5m
Desired Distance
14
Screen size
(Min zoom)
Top
Desired
Distance (m)
<A>
From base
to top of
image (cm)
<C>
Diagonal (inch)
<B>
W (cm) x H (cm)
0.91
1.00
1.25
1.50
2.00
2.41
30.0
33.2
41.5
49.7
66.3
80.0
64 x 40
71 x 45
42
47
89 x 56
59
107 x 67
143 x 89
172 x 108
70
94
113
Zoom Ratio: 1.0x
15
User Controls
Installation menu
The installation menu provides an onscreen display (OSD) for projector
installation and maintenance. Use the OSD only when the message "No signal
input" is displayed on the screen.
The menu options include settings and adjustments for screen size and distance,
focus, keystone correction and more .
1
2
Turn on the projector by pressing "Power" button on the control pad.
Press the "MENU" button on the control pad to launch the OSD for
projector installation and maintenance.
3
4
The background pattern acts as a guide to adjusting the calibration and
alignment settings, such as screen size and distance, focus and more .
The Installation menu includes the following options:
•Projection Mode
•Projection Location
•Auto Keystone settings
•Manual Keystone settings
•Language settings
•Reset to factory default function
Use the up and down arrow keys to select an option, the left and right
arrow keys to adjust selected option settings, and the right arrow key to
enter a submenu for feature setting. The new settings will be saved
automatically upon exiting the menu.
5
Push the menu button anytime to exit the menu and return to the Acer
welcome screen.
16
Onscreen Display (OSD) Menus
The projector has multilingual OSD that allow you to make image adjustments
and change a variety of settings.
Using the OSD menus
•
•
To open the OSD menu, press "MENU" on the remote control.
When the OSD is displayed, use the
keys to select any item in the
main menu. After selecting the desired main menu item, press
submenu for feature setting.
to enter
•
Use the
keys to select the desired item and adjust the settings by
keys.
using the
•
•
•
Select the next item to be adjusted in the submenu and adjust as described
above.
Press "MENU" on the remote control, the screen will return to the main
menu.
To exit OSD, press "MENU" on the remote control again. The OSD menu
will close and the projector will automatically save the new settings.
Main menu
Setting
Sub menu
17
Color
There are many factory presets optimized for various types of
images.
Display Mode
•
•
•
•
•
•
•
Bright: For brightness optimization.
Standard: For common environment.
Movie: For brighter and general movie/video/photo playing.
Dark Cinema: For dark movie content.
Game: For game content.
Sports: For sport picture.
User: Memorize user’s settings.
Use this function to choose a proper color according to the wall.
Wall color
Brightness
There are several choices, including white, light yellow, light blue,
pink, dark green. It will compensate the color deviation due to the
wall color to show the correct image tone.
Adjust the brightness of the image.
•
•
Press
Press
to darken image.
to lighten the image.
"Contrast" controls the difference between the lightest and
darkest parts of the picture. Adjusting the contrast changes the
amount of black and white in the image.
Contrast
•
•
Press
Press
to decrease the contrast.
to increase the contrast.
Adjusts a video image from black and white to fully saturated
color.
Saturation
Tint
•
•
Press
Press
to decrease the amount of color in the image.
to increase the amount of color in the image.
Adjusts the color balance of red and green.
•
•
Press
Press
to increase the amount of green in the image.
to increase the amount of red in the image.
Use this function to choose CT1, CT2, CT3, User mode.
Color
Temperature
18
Choose "On" to automatically optimize the display of dark movie
scenes enabling them to be shown in incredible detail.
Dynamic Black
Gamma
Effects the representation of dark scenery. With greater gamma
value, dark scenery looks brighter.
Advanced
Brilliant Color
Produces an expanded on-screen color spectrum that delivers
enhanced color saturation for bright, true-to-life images. This
feature is "On" by default.
White Peaking
Increases the brightness of whites that are near 100%. (video
sources only)
Noise Reduction
Adjusts signal noise reduction."0" means the noise reduction is off,
">0" increase noise reduction.
Black Extension
Analyzes the current input image and calculates an offset value
which is then added to the analog to digital converter black level
value. This ensures optimum black level for each analog source.
Note: "Saturation" and "Tint" functions are not supported under computer
mode or HDMI mode.
19
Image
Projection mode
•
•
Front: The factory default setting.
Rear: Reverses the image so you can project from behind a
translucent screen.
Projection Location
•
Auto: Automatically adjusts projection location of image.
Desktop
•
•
Ceiling: Turns the image upside down for ceiling-mounted
projection.
Use this function to choose your desired aspect ratio.
Aspect Ratio
•
•
•
•
•
Auto: Keep the image with original width-higth ratio and maxi
mize the image to fit native horizontal or vertical pixels.
4:3: The image will be scaled to fit the screen and displayed
using a 4:3 ratio.
16:9: The image will be scaled to fit the width of the screen and
the height adjusted to display the image using a 16:9 ratio.
Full: Resize image to fit full screen by width (1280 pixels) and
height (800 pixels).
L.Box: Keep original signal aspect ratio and zoom in by 1.333
times.
Auto Keystone
Automatically adjusts vertical image.
Maunal Keystone Adjust image distortion caused by tilting projection. (±40 degrees)
<Note> The Manual Keystone function is unavailable under Auto
Keystone setting to "On".
Sharpeness
Adjusts the sharpness of the image.
•
•
Press
Press
to decrease the sharpness.
to increase the sharpness.
20
H. Position
(Horizontal
position)
•
•
Press
Press
to move the image left.
to move the image right.
V. Position
(Vertical position)
•
•
Press
Press
to move the image down.
to move the image up.
Frequency
Tracking
"Frequency" changes the projector's refresh rate to match the
frequency of your computer’s graphics card. If you can see a vertical
flickering bar in the projected image, use this function to make the
necessary adjustments.
Synchronizes the signal timing of the projector with the graphics card.
If you experience an unstable or flickering image, use this function to
correct it.
HDMI Color Range Adjust the color range of the HDMI image data to correct color display
error.
•
•
•
Auto: Automatically adjust by information from player.
Limited Range: Prosess the input image as limited color range data.
Full Range: Prosess the input image as full color range data.
HDMI Scan Info
Adjust the overscan ratio of the HDMI image on screen.
•
•
•
Auto: Automatically adjust by information from player.
Underscan: Always no overscan on HDMI image.
Overscan: Always keep overscan on HDMI image.
Note: "H. Position", "V. Position", "Frequency" and "Tracking" functions
are not supported under HDMI, DVI or Video mode.
Note: "Sharpness" functions is not supported under HDMI (RGB) or
Computer mode.
Note: "HDMI Color Range" and "HDMI Scan Info" functions are only
supported under HDMI mode.
21
Setting
Closed Caption
Selects a preferred closed captioning mode from CC1, CC2, CC3,
CC4, (CC1 displays captions in the primary language in your area).
Select "Off" to turn off the captioning feature. This function is only
available when a composite video or S-Video input signal is
selected and its system format is NTSC.
<Note> Set your screen aspect ratio to 4:3. This function is not
available when the aspect ratio is "16:9" or "Auto" .
Reset
Press the
button and choose "Yes" to return the parameters
on all menus to the factory default settings.
Management
ECO Mode
Choose "On" to dim the projector lamp which will lower power
consumption, extend the lamp life and reduce noise. Choose "Off"
to return normal mode.
Choose "On" to turn on High Altitude mode. Operate the fans at
full speed continuously to allow for proper high altitude cooling of
the projector.
High Altitude
Turn Off Mode
•
•
Instant Off: Shuts down the projector without fan cooling.
Instant Resume: Resumes the system when the Power button
is pressed again within 2 minutes.
Auto Shutdown
LED Calibration
The projector will automatically shutdown when there is no signal
input after the allocated time. (default is 120 minutes)
Press
after choosing "Yes", please wait for 10 seconds to finish
the white color fine tune process. It helps to adjust LED color
performance.
22
Audio
Volume
Mute
•
•
Press
Press
to decrease the volume.
to increase the volume.
•
•
Choose "On" to mute the volume.
Choose "Off" to restore the volume.
Power On/Off Volume
Alarm Volume
•
Select this function to adjust the notification volume when
turning the projector on/off.
•
Select this function to adjust the volume of any warning
notifications.
3D
3D
Choose "On" to enable DLP 3D function.
•
On: Choose this item while using DLP 3D glasses, quad
buffer (NVIDIA/ATI...) graphic card and HQFS format file or
DVD with corresponding SW player.
•
Off: Turn off 3D mode.
3D Sync Invert
If you see a discrete or overlapping image while wearing DLP 3D
glasses, you may need to execute "Invert" to get best match of
left/right image sequence to get the correct image (for DLP 3D).
23
3D Warning Message Choose "On" to display the 3D warning message.
Note: It needs correct settings on graphic card 3D application program for
correct 3D display.
Note: The SW players, such as Stereoscopic Player and DDD TriDef Media
Player can support 3D format files. You can download these three players
on web page below,
- DDD TriDef Media Player (Trial):
Note: "3D Sync Invert" is only available when 3D is enabled.
Note: There has reminder screen if 3D still enable when power on projector.
Please adjust setting depended on your purpose.
Language
Language
Choose the multilingual OSD menu. Use the
to select your preferred menu language.
or
key
•
Press
to confirm the selection.
24
Appendices
Troubleshooting
If you experience a problem with your Acer projector, refer to the following
troubleshooting guide. If the problem persists, please contact your local reseller
or service center.
Image Problems and Solutions
#
Problem
Solution
1
No image appears
onscreen
•
•
•
Connected as described in the "Getting Started"
section.
Ensure none of the connector pins are bent or
broken.
Make sure you have removed the lens cap and the
projector is switched on.
2
Partial, scrolling
or incorrectly
displayed image
(For PC (Windows
95/98/2000/XP/
Vista/Win7))
•
•
Press "RESYNC" on the remote control.
For an incorrectly displayed image:
•
Open "My Computer," open the "Control
Panel," and then double-click the "Display"
icon.
•
•
Select the "Settings" tab.
Verify that your display resolution setting is
lower than or equal to 1080P-EIA.
Click the "Advanced Properties" button.
•
If the problem still appears, change the monitor display
you are using and follow the steps below:
•
•
•
Verify that the resolution setting is lower than
or equal to 1080P-EIA.
Click the "Change" button under the
"Monitor" tab.
Click "Show all devices". Next, select "Standard
monitor types" under the SP box, and choose
the resolution mode you need under the
"Models" box.
•
Verify that the resolution setting of the
monitor display is lower than or equal to
1080P-EIA.
25
3
Partial, scrolling
or incorrectly
displayed image
(for notebooks)
•
•
Press "RESYNC" on the remote control.
For an incorrectly displayed image:
•
Follow the steps for item 2 (above) to adjust
the resolution of your computer.
•
Press the toggle output settings. Example:
[Fn]+[F4], Compaq [Fn]+[F4], Dell [Fn]+[F8],
Gateway [Fn]+[F4], IBM [Fn]+[F7], HP [Fn]+[F4],
NEC [Fn]+[F3], Toshiba [Fn]+[F5 ]
•
•
If you experience difficulty changing resolutions or
your monitor freezes, restart all equipment
including the projector.
®
®
4
The screen of the
notebook
computer is not
displaying your
presentation
If you are using a Microsoft Windows based
notebook: Some notebook PCs may deactivate their
own screens when a second display device is in use.
Each has a different way to be reactivated. Refer to
your computer's manual for detailed information.
®
®
•
If you are using an Apple Mac OS based
notebook: In System Preferences, open Display and
select Video Mirroring "On".
5
6
Image is unstable
or flickering
•
•
Adjust the "Tracking" to correct it. Refer to the
"Image" section for more information.
Change the display color depth settings on your
computer.
Image has vertical
flickering bar
•
•
Use "Frequency" to make an adjustment. Refer to
the "Image" section for more information.
Check and reconfigure the display mode of your
graphics card to make it compatible with the
projector.
7
8
Image is out of
focus
•
•
•
Make sure the lens cap is removed.
Adjusts the focus ring on the projector lens.
Make sure the projection screen is within the
required distance of 2.99-7.87 feet (0.91-2.40 meters)
from the projector. Refer to the "How to Get a
Preferred Image Size by Adjusting Distance and
Zoom" section for more information.
Image is stretched
when displaying a
"widescreen"
DVD title
When you play a DVD encoded in anamorphic or 16:9
aspect ratio you may need to adjust the following
settings:
•
If you play a 4:3 format DVD title, please change the
format to 4:3 in the projector OSD.
•
If the image is still stretched, you will also need to
adjust the aspect ratio. Set up the display format to
16:9 (wide) aspect ratio on your DVD player.
•
If you play an Letterbox(LBX) format DVD title,
please change the format to Letterbox(LBX) in the
projector OSD.
26
9
Image is too small
or too large
•
•
Adjust the zoom ring on the top of the projector.
Move the projector closer to or further from the
screen.
•
Press "MENU" on the remote control or on the
control panel. Go to "Image --> Aspect Ratio" and
try different settings.
10
Image has slanted
sides
•
•
If possible, reposition the projector so that it is
centered on the screen.
Press the "Keystone
/
" on the OSD or the
remote control until the sides are vertical.
11
Image is reversed
•
Select "Image --> Projection" on the OSD and adjust
the projection direction.
Problems with the Projector
#
Condition
Solution
1
The projector stops responding
to all controls
If possible, turn off the projector, then
unplug the power cord and wait at least 30
seconds before reconnecting power.
27
OSD Messages
#
Condition
Message
Message Reminder
1
Fan Fail - the system fan is not working.
Projector Overheated - the projector has exceeded its
recommended operating temperature and must be allowed to
cool down before it may be used.
28
LED & Alarm Definition Listing
LED Messages
Lamp_LED
Red
Temp_LED
Red
Power_LED
Red
Power_LED
Message
Blue
--
Input Power Plug
Flash ON to
OFF 100ms
Flash ON to
OFF 100ms
Flash ON to
OFF 100ms
Standby
--
--
--
--
--
--
ON
--
--
Power button ON
Lamp retry
ON
--
Quick
Flashing
Power off (Cooling
state)
--
--
--
--
Quick
Flashing
--
--
Power button OFF:
Cooling completed;
Standby Mode
ON
Error (Thermal
Failure)
--
--
ON
--
--
--
ON
ON
ON
Error (Fan lock)
Quick
Flashing
Error (Lamp
breakdown)
ON
--
29
Ceiling Mount Installation
If you wish to install the projector using a ceiling mount, please refer to the
steps below:
1
Drill four holes into a solid, structurally sound part of the ceiling, and
secure the mount base.
Note: Screws are not included. Please obtain the appropriate
screws for your type of ceiling.
2
Secure the ceiling rod using the appropriate type of four-cylinder screws.
Ceiling Mount Base
- Attach to ceiling
Short Rod
Long Rod
Extension Rod
Long Cylinder Cap
Allen Key
- For tightening/looseni
Screw Type A
50 mm length / 8 mm diameter -
Tightening Screw
Medium Rod
30
3
Use the appropriate number of screws for the projector size to attach the
projector to the ceiling mount bracket.
Screw Type B
Smaller Washer
Large Washer
Projector Bracket
Supports projector and allows -
for adjustments
Spacer
- For heat dissipation
Note: It is recommended that you keep a reasonable space
between the bracket and the projector to allow for proper heat
distribution. Use two washers for extra support, if deemed
necessary.
4
Attach the ceiling bracket to the ceiling rod.
Large cylinder cap
Allen Key
- For tightening/loosening
Screw Type A
50 mm length -
Tightening Screw
08 mm diameter
31
5
Adjust the angle and positioning as necessary.
Tightening Screw
Allen Key
3
Allen Key
Tightening Screw
Note: The appropriate type of screw and washer for each model is
listed in the table below. 3 mm diameter screws are enclosed in
the screw pack.
Models
Screw Type B
Diameter (mm)
Washer Type
Length (mm)
20
Large
V
Small
V
K335/L320/LK-W20
3
49 mm
62 mm
SCREW SPEC. M3 x 20 mm
32
Specifications
The specifications listed below are subject to change without notice. For final
specs, please refer to Acer's published marketing specifications.
®
Projection system
DLP
Resolution
WXGA (1280 x 800)
Computer compatibility
IBM PC and compatibles, Apple Macintosh, iMac and
VESA standards: SXGA, XGA, SVGA, VGA, WXGA
Video compatibility
NTSC (3.58/4.43), PAL (B/D/G/H/I/M/N), SECAM (B/D/G/
K/K1/L), HDTV (720p, 1080i, 1080p), EDTV (480p,
576p), SDTV (480i, 576i)
Aspect ratio
Auto, Full, 4:3, 16:9, L.Box
1.07 billion colors
Displayable colors
Projection lens
F# 1.5, f = 13.92 mm
Projection screen size (diagonal) 30" (0.76 m) - 80"(2.03 m)
Projection distance
Throw ratio
2.99' (0.91 m) - 7.87' (2.40 m)
1.4
Horizontal scan rate
Vertical refresh scan rate
Keystone correction
Audio
30 k - 100 kHz
50 - 120 Hz
+/- 40 degrees
Internal speaker with 3 W x 1 output
2.0 kg (4.41 lbs)
Weight
Dimensions (W x D x H)
231.98 mm x 165.77 mm x 46.3 mm (9.13" x 6.53" x
1.82")
Power supply
AC 100 – 240 V, 50-60 Hz
Power consumption
Normal mode: 135 W +/- 10% @ 110 Vac
ECO mode: 110 W +/-10% @ 110 Vac
Standby < 0.5 W
Operating temperature
I/O connectors
5 ºC to 40 ºC / 41 ºF to 104 ºF
•
•
•
•
•
•
•
•
•
Power socket x1
SD x1
USB A x1: for multimedia
Mini USB B x 1: for DoUSB
HDMI (MHL) x1
VGA input x1
Composite input x1
Audio input x1
Audio output x 1
33
Standard package contents
•
•
•
•
•
•
AC power cord x1
VGA cable x1
Composite video x1
Remote control x1
Battery x 2 (for remote control)
User's guide (CD-ROM) x1 (for projector
function)
•
User's guide (CD-ROM) x1 (for multi-media and
wireless functions)
•
•
Quick start guide x1 (for projector function)
Quick start guide x1 (for multi-media and
wireless functions)
•
Carrying case x1
* Design and specifications are subject to change without notice.
34
Compatibility modes
A. VGA Analog
1
VGA Analog - PC Signal
Modes
VGA
Resolution
V.Frequency [Hz] H.Frequency [KHz]
640x480
640x480
60
72
31.5
37.9
37.5
43.3
61.9
35.1
37.9
48.1
46.9
53.7
77.4
48.4
56.5
60.0
68.7
99.0
63.8
67.5
77.1
64.0
77.0
80.0
60.0
75.2
65.3
31.4
34.9
37.9
48.4
68.7
75.0
60.0
640x480
75
640x480
85
640x480
120
56
SVGA
800x600
800x600
60
800x600
72
800x600
75
800x600
85
800x600
120
60
XGA
1024x768
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
640x480
70
75
85
120
70
SXGA
75
85
60
72
75
QuadVGA
60
75
SXGA+
60
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
i Mac DV (G3)
60
640x480
66.6 (67)
60
800x600
1024x768
1152x870
1280x960
1024x768
60
75
75
75
35
2
VGA Analog - Extended Wide timing
Modes
WXGA
Resolution
1280x768
1280x768
1280x768
1280x720
1280x800
1440x900
V.Frequency [Hz] H.Frequency [KHz]
60
75
85
60
60
60
60
47.8
60.3
68.6
44.8
49.6
59.9
65.3
WSXGA+
1680x1050
1920x1080
(Reduced
Blanking Timing)
60
60
66.6
47.7
1366x768
3
VGA Analog - Component Signal
Modes
480i
Resolution
V.Frequency [Hz] H.Frequency [KHz]
720x480
(1440x480)
720x576
59.94(29.97)
50(25)
15.7
15.6
576i
(1440x576)
480p
576p
720x480
720x576
59.94
50
31.5
31.3
45.0
37.5
33.8
28.1
67.5
56.3
720p
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
60
720p
50
1080i
1080i
1080p
1080p
60 (30)
50 (25)
60
50
B. HDMI Digital
1
HDMI - PC Signal
Modes
VGA
Resolution
640x480
640x480
640x480
640x480
640x480
800x600
800x600
800x600
800x600
V.Frequency [Hz] H.Frequency [KHz]
60
72
75
85
120
56
60
72
75
31.5
37.9
37.5
43.3
61.9
35.1
37.9
48.1
46.9
SVGA
36
800x600
800x600
85
120
60
53.7
77.4
48.4
56.5
60.0
68.7
99.0
63.8
67.5
77.1
64.0
77.0
80.0
60.0
75.2
65.3
31.4
34.9
37.9
48.4
68.7
75.0
60.0
XGA
1024x768
1024x768
1024x768
1024x768
1024x768
1152x864
1152x864
1152x864
1280x1024
1280x1024
1280x1024
1280x960
1280x960
1400x1050
640x480
70
75
85
120
70
SXGA
75
85
60
72
75
QuadVGA
60
75
SXGA+
60
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
PowerBook G4
i Mac DV (G3)
60
640x480
66.6 (67)
60
800x600
1024x768
1152x870
1280x960
1024x768
60
75
75
75
2
HDMI - Extended Wide timing
Modes
WXGA
Resolution
V.Frequency [Hz] H.Frequency [KHz]
1280x768
1280x768
60
75
85
60
60
60
60
47.8
60.3
68.6
44.8
49.6
59.9
65.3
1280x768
1280x720
1280x800
1440x900
WSXGA+
1680x1050
1920x1080
(Reduced Blanking
Timing)
60
60
66.6
47.7
1366x768
37
3
HDMI - Video Signal
Modes
480i
576i
Resolution
V.Frequency [Hz] H.Frequency [KHz]
720x480(1440x480)
720x576(1440x576)
720x480
59.94 (29.97)
15.7
15.6
31.5
31.3
45.0
37.5
33.8
28.1
67.5
56.3
50 (25)
59.94
50
480p
576p
720p
720p
1080i
1080i
1080p
1080p
720x576
1280x720
1280x720
1920x1080
1920x1080
1920x1080
1920x1080
60
50
60 (30)
50 (25)
60
50
Graphic source
monitor range
limits
Horizontal scan rate:
30k~100kHz
Vertical scan rate:
Max. pixel rate
50~120Hz
150MHz
38
Regulations and safety notices
FCC notice
This device has been tested and found to comply with the limits for a Class B
digital device pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This device generates, uses, and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this device does cause harmful interference to radio or television
reception, which can be determined by turning the device off and on, the user
is encouraged to try to correct the interference by one or more of the following
measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the device and receiver.
Connect the device into an outlet on a circuit different from that to which
the receiver is connected.
•
Consult the dealer or an experienced radio/television technician for help.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
to maintain compliance with FCC regulations.
Notice: Peripheral devices
Only peripherals (input/output devices, terminals, printers, etc.) certified to
comply with the Class B limits may be attached to this equipment. Operation
with non-certified peripherals is likely to result in interference to radio and TV
reception.
Caution
Changes or modifications not expressly approved by the manufacturer could
void the user's authority, which is granted by the Federal Communications
Commission, to operate this device.
Operation conditions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Notice: Canadian users
This Class B digital apparatus complies with Canadian ICES-003.
39
Remarque à l'intention des utilisateurs canadiens
Cet appareil numérique de la classe B est conforme a la norme NMB-003 du
Canada.
Declaration of Conformity for EU countries
Acer hereby declares that this projector series is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Compliant with Russian regulatory certification
Radio device regulatory notice
Note: The regulatory information below is for models with
wireless LAN and/or Bluetooth only.
General
This product complies with the radio frequency and safety standards of any
country or region in which it has been approved for wireless use. Depending on
configurations, this product may or may not contain wireless radio devices (such
as wireless LAN and/or Bluetooth modules).
Canada — Low-power license-exempt radio
communication devices (RSS-210)
a
Common information
Operation is subject to the following two conditions:
1. This device may not cause interference, and
2. This device must accept any interference, including interference
that may cause undesired operation of the device.
b
Operation in 2.4 GHz band
To prevent radio interference to the licensed service, this device is
intended to be operated indoors and installation outdoors is subject
to licensing.
List of applicable countries
This device must be used in strict accordance with the regulations and constraints in the
country of use. For further information, please contact the local office in the country of use.
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi
New Taipei City 221, Taiwan
Declaration of Conformity
We,
Acer Incorporated
8F, 88, Sec. 1, Xintai 5th Rd., Xizhi, New Taipei City 221, Taiwan
Contact Person: Mr. RU Jan, e-mail:[email protected]
And,
Acer Italy s.r.l
Via Lepetit, 40, 20020 Lainate (MI) Italy
Tel: +39-02-939-921 ,Fax: +39-02 9399-2913
Declare under our own responsibility that the product:
Product:
Projector
Trade Name:
Model Number:
Acer
CWX1139
K335/L320/LK-W20
To which this declaration refers conforms to the relevant standard or other standardizing documents:
ꢀ
ꢀ
ꢀ
ꢀ
ꢀ
EN 55022:2006/A1:2007 Class B; EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009 Class A; EN61000-3-3:2008
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
EN 50581:2012
Regulation (EC) No. 1275/2008; EN 62301:2005
We hereby declare above product is in compliance with the essential requirements and other relevant
provisions of EMC Directive 2004/108/EC, Low Voltage Directive 2006/95/EC, RoHS Directive
2011/65/EU and Directive 2009/125/EC with regard to establishing a framework for the setting of ecodesign
requirements for energy-related product.
Year to begin affixing CE marking 2013.
_______________________________
RU Jan / Sr. Manager
Mar. 25, 2013
Date
Regulation, Acer Inc.
Acer America Corporation
333 West San Carlos St.,
Suite 1500
San Jose, CA 95110
U. S. A.
Tel: 254-298-4000
Fax: 254-298-4147
Federal Communications Commission
Declaration of Conformity
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
The following local Manufacturer / Importer is responsible for this declaration:
Product:
DLP Projector
Model Number:
Machine Type:
CWX1139
K335/L320/LK-W20
Acer America Corporation
Name of Responsible Party:
Address of Responsible Party: 333 West San Carlos St.
Suite 1500
San Jose, CA 95110
U. S. A.
Contact Person:
Phone No.:
Fax No.:
Acer Representative
254-298-4000
254-298-4147
|