Vizio Ir 200bc User Manual

OPERATING INSTRUCTIONS  
BATTERY CHARGER  
IR-200BC  
TABLE OF CONTENTS  
1. SAFETY PRECAUTIONS ........................... 2  
2. GENERAL DESCRIPTION ......................... 3  
3. HANDLING PRECAUTIONS ...................... 3  
4. NOMENCLATURE AND FUNCTIONS ....... 4  
5. CHARGING ................................................. 5  
6. TROUBLESHOOTING ................................ 7  
7. SPECIFICATIONS ...................................... 8  
Accessories ................................................. 8  
Thank you for purchasing TOA's Battery Charger.  
Please carefully follow the instructions in this manual to ensure long, trouble-free use of your equipment.  
• Switch off the power, and unplug the power supply  
plug from the AC outlet for safety purposes when  
cleaning or leaving the unit unused for 10 days or  
more. Doing otherwise may cause a fire or electric  
shock.  
• Make sure to observe the following handling  
precautions so that a fire or personal injury does  
not result from leakage or explosion of the battery.  
· Be sure to use only the rechargeable battery  
designed for use with the infrared wireless  
microphone  
• Use the dedicated AC adapter for the unit. Note  
that the use of other adapter may cause a fire.  
· Avoid mixed use of new and old batteries,  
batteries of different types, or fully charged and  
discharged batteries in the same microphone.  
· Do not short, disassemble, heat nor put the  
battery into a fire.  
• Avoid charging microphones installed with  
rechargeable batteries other than the dedicated IR-  
200BT battery. Charging any other than the  
specified battery could result in fire or personal  
injury due to battery rupture.  
· Do not solder a battery directly.  
· Note correct polarity (positive and negative  
orientation) when inserting a battery in the unit.  
· Avoid locations exposed to the direct sunlight,  
high temperature and high humidity when storing  
batteries.  
• When the infrared wireless microphone is not in  
use for 2 weeks or more, be sure to take the  
batteries out of the microphone because battery  
leakage may cause a fire, personal injury, or  
contamination of environment.  
FCC Compliance  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  
(1) this device may not cause harmful interference, and  
(2) this device must accept any interference received, including interference that may cause undesired  
operation.  
Any modifications made to this device that are not approved by TOA Corporation may void the authority  
granted the user by the FCC to operate this equipment.  
Note: This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against  
harmful interference when the equipment is operated in a commercial environment. This equipment  
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance  
with the instruction manual, may cause harmful interference to radio communications. Operation of this  
equipment in a residential area is likely to cause harmful interference in which case the user will be  
required correct the interference at his own expense.  
2. GENERAL DESCRIPTION  
The TOA IR-200BC is a dedicated battery charger for the IR-200M and IR-300M Infrared Wireless  
Microphones.  
It employs a quick charging system for nickel metal hydride (NiMH) batteries, allowing up to 2 infrared wireless  
microphones to be fully charged within 3 hours.  
3. HANDLING PRECAUTIONS  
• Since the supplied power cord is designed for use specifically with the IR-200BC charger, do not use it with  
equipment other than the IR-200BC.  
• Use the IR-200BC in locations where an ambient temperature ranges from 0 to 40 ºC (32 to 104 ºF).  
• When cleaning the case, be sure to first switch off the power, then wipe with a dry cloth. Never use benzene,  
thinner, alcohol or chemically processed towels, as these may damage the charger's components and parts.  
• Clean the charging terminals on a regular basis using a dry cotton swab. Dirty terminals can cause poor  
electrical contact and cause batteries to be charged incorrectly.  
3
4. NOMENCLATURE AND FUNCTIONS  
2
3
4
5
8
6
7
6
1
7
1. Power switch  
5. Infrared wireless microphone receptacle  
• Use the mounting adapter when charging the  
IR-200M microphone.  
To turn on the power, set this switch to the [ ]  
position. To turn off the power, shift this switch  
back.  
• When charging the IR-300M microphone,  
remove the mounting adapter and insert the  
microphone directly into the receptacle.  
2. Mounting Adapter  
(factory-attached to the charger)  
Used when charging the IR-200M handheld  
infrared wireless microphone.  
6. Full-charge indicator  
Lights green once the battery is fully charged.  
Remove this adapter when charging the IR-300M  
hands-free infrared wireless microphone. (Refer to  
p. 5 "Charging.")  
7. Charging indicator  
Lights red continuously while charging is in  
progress.  
3. Power indicator  
Lights when the power is switched on.  
8. Power input terminal  
Connect the supplied AC adapter to this terminal.  
4. Screwdriver inlet  
Insert the setting screwdriver supplied with the  
infrared wireless microphone into this inlet when  
storing it.  
[Indicator status table]  
Charging indicator (red) Full-charge indicator (green)  
Status  
Charging in progress  
Lit  
Unlit  
Unlit  
Lit  
Charging completed  
Flashing  
Unlit  
Outside the operating temperature range  
(refer to p. 7 "Troubleshooting.")  
Both indicators light alternately.  
Charging failure (refer to p. 7 "Troubleshooting.")  
4
5. CHARGING  
Avoid charging microphones installed with rechargeable batteries  
other than the dedicated IR-200BT battery.  
CAUTION  
Charging any other than the specified battery could result in fire or  
personal injury due to battery rupture.  
Notes  
• Use the charger in locations where the ambient temperature range is between 0 and 40 ºC (32 to 104 ºF).  
• Charge the IR-200BT battery before using it.  
• If an infrared wireless microphone containing an IR-200BT battery has been stored for a long period of time,  
it is recommended that the microphone be charged before use.  
• Avoid using the charger in locations subject to strong vibrations, as the resulting poor electrical contact may  
prevent correct charging.  
• Do not frequently insert and remove the microphone from the charger during charging, as this could reduce  
the number of times that the IR-200BT can be effectively charged and discharged.  
• Rechargeable batteries are consumables and do not last indefinitely. If the battery operating time becomes  
extremely short even when it has been fully charged, the battery has reached the end of its life and must be  
replaced. Be sure to replace the battery with one designated for use with the microphone (IR-200BT).  
Tip: Under normal use conditions, the battery can cycle through approximately 500 charges and discharges,  
after which it will usually need to be replaced.  
IR-200M (optional)  
Mounting adapter  
(pre-installed)  
4
1
Power switch  
Full-charge  
indicator  
IR-300M (optional)  
Power input terminal  
5
3 , 6  
Charger  
Power switch  
Charging indicator  
Power indicator  
Supplied AC adapter  
1
Handling the power cord  
AC adapter plug  
2
To AC wall outlet  
Supplied power cord  
Cord  
Bottom view of the charger  
Step 1. Connect the power cord to the AC adapter, then connect the AC adapter to the charger.  
Once connected, push the cord into the slot in the charger's bottom surface to prevent the AC adapter  
plug from accidentally slipping out of place. (Refer to "Handling the power cord" in the figure above.)  
Step 2. Insert the AC power plug into an AC wall outlet.  
Step 3. Set the charger's power switch to ON.  
Confirm that the power indicator is lit.  
5
Step 4. Turn off the power of the infrared wireless microphone to be charged, then insert the 2 IR-200BT  
rechargeable batteries into the microphone. For proper battery insertion, refer to the instruction  
manual enclosed with the infrared wireless microphone.  
Note  
Charging cannot be correctly performed if the infrared wireless microphone's power switch is set to  
the ON position.  
Step 5. Insert the infrared wireless microphone fully into  
the charger's microphone receptacle and confirm  
that the charging indicator (red) is lit.  
Removing the mounting adapter  
[For the IR-200M microphone]  
Mounting adapter  
• Leave the mounting adapter attached.  
• Insert the microphone into the hole in the  
adapter to charge.  
[For the IR-300M microphone]  
Charger  
Remove the mounting adapter to charge.  
(Refer to the figure at right.)  
Pull up the adapter holding down this part  
Charging takes approximately 3 hours, after which  
the full-charge indicator lights green.  
(another on the opposite side).  
Step 6. Turn off the charger's power once charging is complete.  
Notes  
• Be sure to turn off the charger's power after charging is complete in order to save standby power.  
• The infrared wireless microphone becomes warm after charging completion, however this is not a  
failure.  
• Hold the charger when detaching the infrared wireless microphone from the charger.  
6
6. TROUBLESHOOTING  
Symptom  
Possible cause  
Remedy  
Power indicator does not • The AC adapter is not plugged into • Make sure the AC adapter is  
light even if the power  
switch is turned on.  
a working AC outlet, or is not  
plugged in correctly.  
plugged in to a working AC wall  
outlet correctly.  
• AC adapter plug is not connected to • Connect the plug to the charger's  
the charger. power input terminal.  
Charging indicator (red) • The batteries used in the • Install the appropriate dedicated IR-  
does not light even when  
the infrared wireless  
microphone may not be dedicated  
IR-200BT rechargeable batteries.  
200BT rechargeable battery in the  
microphone.  
microphone is inserted • The infrared wireless microphone • Make sure that the microphone is  
into the microphone  
receptacle.  
may not be seated correctly in the  
microphone receptacle.  
inserted fully into charger as far as  
it will go.  
[For the IR-200M]  
• The mounting adapter may not be • Install the mounting adapter  
installed correctly. correctly.  
Inserting the infrared • The ambient temperature may • Perform charging within the  
wireless microphone into  
the microphone receptacle  
causes the charging  
indicator (red) to flash.  
exceed the permissible operating  
temperature range (0 to 40 ºC, or  
32 to 104 ºF), preventing charging.  
operating temperature range (0 to  
40 ºC, or 32 to 104 ºF).  
Full-charge  
(green) always lights soon.  
indicator • The  
dedicated  
IR-200BT • Replace the rechargeable battery  
rechargeable battery has probably  
reached the end of its life cycle  
(usually after about 500 charges  
and discharges).  
with a new one.  
Full-charge indicator does • The infrared wireless microphone's • Set  
not light even 3 hours after power switch may be set to ON. microphone's power switch to OFF.  
charging has been started • The battery may be at the end of its • Replace the rechargeable battery  
the  
infrared  
wireless  
(maximum charging time:  
3 hours).  
life.  
with a new one.  
Both the charging indicator • The microphone may have been • Use  
a
dedicated IR-200BT  
(red) and the full-charge  
indicator (green) light  
alternately.  
installed with a non-IR-200BT  
rechargeable battery.  
• There may be foreign objects (such • Remove such foreign objects.  
as metals) in the microphone  
receptacle.  
rechargeable battery in the infrared  
wireless microphone.  
• The battery may be at the end of its • Replace the rechargeable battery  
life. with a new one.  
• The infrared wireless microphone's • Detach the infrared wireless  
power switch may be set to ON.  
microphone from the charger and  
set the microphone power switch to  
the OFF position, then reinsert the  
microphone into the charger.  
7
7. SPECIFICATIONS  
Power Source  
AC mains, 50/60 Hz (Power is supplied from the enclosed AC adapter.)  
Current Consumption  
Charging Time  
Max. 2 A  
Max. 3 hours  
2 pieces*1  
Number of wireless  
microphones to be  
charged simultaneously  
Operating Temperature  
Operating Humidity  
Finish  
0 to 40 °C (32 to 104 °F)  
30 to 85% RH  
Case:  
Microphone receptacle section: PPE resin, black  
ABS resin, metallic gray, 50% gloss, paint  
Dimensions  
Weight  
238 (w) x 83 (h*2) x 98 (d) mm (9.37" x 3.27" x 3.86")  
635 g or 1.4 lb (charger with the mounting adapters attached)  
Note: The design and specifications are subject to change without notice for improvement.  
• Accessories  
Power cord (2 m or 6.56 ft)*3 ......................................................................... 1  
AC adapter (DC cord length: 1.5 m or 4.92 ft)*3 ............................................ 1  
Mounting adapter (pre-installed) ................................................................... 2  
• Optional products  
Rechargeable battery: IR-200BT-2 (containing 2 pieces)  
*1 Using the mounting adapter allows one each of the IR-200M and IR-300M to be charged in combination.  
*2 Height is 109.5 mm (4.31") when the mounting adapter is installed.  
*3 Not supplied with the IR-200BC KR. For the usable power supply cord and AC adapter, contact your  
nearest TOA dealer.  
Traceability Information for Europe (EMC directive 2004/108/EC)  
Manufacturer:  
TOA Corporation  
7-2-1, Minatojima Nakamachi, Chuo-ku, Kobe, Hyogo,  
Japan  
Authorized representative:  
TOA Electronics Europe GmbH  
Suederstrasse 282, 20537 Hamburg,  
Germany  
133-07-272-70  

Mitsubishi Electronics 25kkc User Manual
Sanyo Twicell Hf E5u User Manual
Sanyo Uf553443r User Manual
Sonic Alert Rh100 User Manual
Trane Air Conditioner 61e User Manual
White Rodgers Sst1600 User Manual
Xerox 440 User Manual
Xerox Workcentre 7675 User Manual
Xpelair Idh1 8 User Manual
Zebra Technologies Mp User Manual