Trane Air Conditioner Vav Svn01e En User Manual

Installation/  
Operator  
Maintenance  
VariTrane™ Single-Duct  
and Fan-Powered Units  
AllVariTraneVAV Models with pneumatic, electronic, DDC controls and diffusers.  
June 2006  
VAV-SVN01E-EN  
Contents  
Service Model Number Description ..................4 – 14  
General Information ............................................... 15  
Literature Contents  
Receiving and Handling  
Warnings and Cautions Explanations  
Unit Information ............................................. 16 – 17  
Single-Duct Units  
Dual-Duct Units  
Fan-Powered and Low-Height Units  
Unit Installation .............................................. 18 – 31  
Hanging Bracket Locations  
Unit Weights  
Water Coil Connections  
Unit Accessibility  
Clearances  
Actuator Mounting  
Unit Setup ......................................................32 – 46  
Flow Sensor P vs. Airflow Delivery  
Maximum Fan Motor Amperage  
(SCR) Motor Speed Control Adjustment Procedure  
Electrically Commutated Motor (ECM)  
ECM CFMTables  
Wiring Diagrams ............................................. 47 – 54  
Maintenance .......................................................... 55  
Motors  
FanWheel  
Filter  
Water Coil  
Fan Motor Replacement  
Installation of Diffusers .......................................... 56  
T-Bar Ceiling  
Concealed Spline Ceiling  
Drywall/Plaster Ceiling  
VAV-SVN01E-EN  
3
Service Model  
Number Description  
Single-Duct Units  
Digit 1, 2—UnitType  
WARNING  
FM00 FM – Customer-supplied  
Fiberglass Wool!  
actuator & controller  
FM01 FM Trane actuator w/ cusomer-  
supplied control  
VC  
VariTrane single-duct  
WARNING: ALL INSULATED UNITS  
(except closed-cell foam insulation)  
CONTAIN FIBERGLASSWOOL! Read  
this literature prior to installation for  
proper instruction. Disturbing the  
insulation in this product during  
installation, maintenance or repair will  
expose you to airborne particles of  
glass wool fibers and ceramic fibers  
known to the state of California to  
cause cancer through inhalation. Glass  
wool fibers may also cause respiratory,  
skin or eye irritation.  
Digit 3—Reheat  
C
Cooling Only  
VMA1 FM – Johnson controlsVMA-1410  
VMA2 FM – Johnson controlsVMA-1420  
PWR1 FM – Seimens 540-100 w/  
GDE131.1P actuator  
PWR4 FM – Seimens 540-100 w/Trane  
actuator  
PWR5 FM – Seimens 540-100 w/  
GDE131.1U actuator  
AT01 FM – Automated Logic U341V+  
AT02 FM – Automated Logic U141V+  
EI05 Analog With optional on/off  
reheat  
EI28 Analog With optional on/off  
reheat with dual-minimum cfm  
EI29 Analog With optional on/off  
reheat with constant-volume cfm  
PC00 PN – N.C.Trane pneumatic  
actuator  
PC04 PN – N.C. with optional on/off HW,  
DA Stat  
PC05 PN – N.C. with optional on/off  
electric, RA Stat  
E
Electric Heat  
W
HotWater Heat  
Digit 4—Development Sequence  
Sixth  
Digit 5, 6—PrimaryAirValve  
F
04  
05  
06  
08  
10  
12  
14  
16  
24  
4" inlet (225 cfm)  
5" inlet (350 cfm)  
6" inlet (500 cfm)  
8" inlet (900 cfm)  
10" inlet (1400 cfm)  
12" inlet (2000 cfm)  
14" inlet (3000 cfm)  
16" inlet (4000 cfm)  
24" x 16" inlet (8000 cfm)  
Digit 7, 8—Not Used  
00 N/A  
Digit 9—Not Used  
N/A  
Digit 10, 11—Design Sequence  
H0 Fourth (factory assigned)  
0
PN00 PN – N.O.Trane pneumatic  
actuator, RA Stat  
Digit 12, 13, 14, 15—Controls  
ENON No controls, field-installed  
DDC/electric  
PNON No controls, field-installed  
pneumatic  
DD00 Trane elec actuator only  
DD01 DDC – Cooling only  
DD02 DDC – N.C. on/off water valve  
control  
PN04 PN – N.O. PVR, DA Stat  
PN05 PN – N.O. PVR, RA Stat  
PN11 PN – N.O. dual-minimum cfm,  
DA Stat  
PN32 PN – WaterValve, N.O. constant  
volume, DA Stat  
PN34 PN – Electric heat, N.O. constant  
volume, DA Stat  
DD03 DDC – Prop hot water valve  
control  
DD04 DDC – On/off electric heat  
DD05 DDC – Pulse-width modulation  
electric heat  
DD07 DDC – N.O. on/off water valve  
control  
DD11 LonTalk DDC Controller—  
Cooling only  
DD12 LonTalk DDC Controller w/ N.C.  
on/off hot water control  
DD13 LonTalk DDC Controller w/  
proportional hot water control  
DD14 LonTalk DDC Controller–on/off  
electric heat control  
DD15 LonTalk DDC Controller w/  
pulse-width modulation electric  
heat control  
DD17 LonTalk DDC Controller w/ N.O.  
on/off hot water control  
Notes:  
N.C. =  
N.O. =  
Normally-closed  
Normally-opened  
DA Stat = Direct-acting pneumatic t-stat  
(by others)  
RA Stat = Reverse-acting pneumatic  
t-stat (by others)  
PN =  
FM =  
Pneumatic  
Factory installation of customer-  
supplied controller  
PVR =  
PneumaticVolume Regulator  
Digit 16—Insulation  
A
B
C
D
F
1/2" Matte-faced  
1" Matte-faced  
1/2" Foil-faced  
1" Foil-faced  
1" Double-wall  
3/8" Closed-cell  
G
4
VAV-SVN01E-EN  
Service Model  
Number Description  
Single-Duct Units (con't.)  
Digit 17—Not Used  
Digit 23—Transformer  
Digit 27, 28, 29—Electric Heat kW  
0
N/A  
Digit 18—Not Used  
N/A  
0
1
2
3
4
5
6
7
8
None  
000  
050  
010  
015  
None  
120/24 volt (50VA)  
208/24 volt (50VA)  
240/24 volt (50VA)  
277/24 volt (50VA)  
480/24 volt (50VA)  
347/24Volt (50VA)  
575/24Volt (50VA)  
380/24Volt (50VA)  
0.5 kW  
1.0 kW  
1.5 kW  
0
Digit 19—Outlet Plenum (Connection is  
Slip & Drive)  
0
A
B
C
D
E
F
None  
460  
46.0 kW  
1 Outlet RH  
1 Outlet END  
Notes:  
1 Outlet LH  
0.5 to 8.0 kW – ½ kW increments  
8.0 to 18.0 kW – 1 kW increments  
18.0 to 46.0 kW – 2 kW increments  
Note: ForVCEF units with transformers  
theVA depends on the staging, control,  
and contactor type (ranges are 40VA  
to 75VA)  
2 Outlets, 1 RH, 1 END  
2 Outlets, 1 LH, 1 END  
2 Outlets, 1 RH, 1 LH  
3 Outlets, 1 LH, 1 RH, 1 END  
4 Outlets, 1 LH, 1 RH, 2 END  
H
J
Digit 30—Electric Heat Stages  
0
1
2
3
None  
1 Stage  
2 Stages Equal  
3 Stages Equal  
Digit 24—Disconnect Switch  
0
W
Note: See unit drawings for outlet sizes/  
damper information.  
None  
With  
Digit 20—Not Used  
Note: VCCF,VCWF Toggle Disconnect  
VCEF – Door Interlocking Power  
Disconnect  
Digit 31—Contactors  
0
N/A  
0
1
2
3
4
None  
24-volt magnetic  
24-volt mercury  
PE with magnetic  
PE with mercury  
Digit 21—Water Coil  
0
1
2
None  
1-Row  
2-Row  
Digit 25—Power Fuse  
0
W
None  
With  
Digit 32—Not Used  
0 N/A  
Digit 22—Electrical Connections (VCCF,  
VCWF can be flipped in the field to  
achieve opposite-hand connection)  
Digit 26—Electric HeatVoltage  
0
None  
A
B
C
D
E
F
208/60/1  
208/60/3  
240/60/1  
277/60/1  
480/60/1  
480/60/3  
347/60/1  
575/60/3  
380/50/3  
120/60/1  
L
R
0
Left (Airflow hitting you in the  
face)  
Right (Airflow hitting you in the  
face)  
Opposite side connection – coil  
and control  
G
H
J
K
VAV-SVN01E-EN  
5
Service Model  
Number Description  
Dual-Duct Units  
Digit 1, 2, 3—UnitType  
VDD VariTrane dual-duct  
Digit 4—Development Sequence  
Digit 19—Outlet Plenum (Connection is  
slip & drive)  
FM00 FM – Customer-supplied  
actuator & controller  
FM01 FM –Trane actuator w/  
customer-supplied controller  
PC03 PN – N.C. heating/ N.O. cooling  
w/ PVRs, DA stat  
PN08 PN – N.O. heating/ N.O. cool  
act. only, RA stat  
PN09 PN – N.O. htg/clg vlvs w/ PVRs,  
DA stat  
0
none  
A
B
C
D
E
F
1 outlet–RH  
F
Sixth  
1 outlet–END  
1 outlet–LH  
Digit 5, 6—PrimaryAirValve  
05  
06  
08  
10  
12  
14  
16  
5" inlet (350 cfm)  
6" inlet (500 cfm)  
6" inlet (900 cfm)  
10" inlet (1400 cfm)  
12" inlet (2000 cfm)  
14" inlet (3000 cfm)  
16" inlet (4000 cfm)  
2 outlets–1 RH, 1 END  
2 outlets–1 LH, 1 END  
2 outlets–1 RH, 1 LH  
2 outlets - END  
3 outlets–1 LH, 1 RH, 1 END  
4 outlets–1 LH, 1 RH, 2 END  
G
H
J
PN10 PN – N.O. htg/clg w/ PVRs (cv  
disch), DA stat.  
Note: See unit drawings for outlet sizes/  
damper information.  
Notes:  
N.C. =  
N.O. =  
Digit 7, 8—SecondaryAirValve  
Normally-closed  
Normally-opened  
05  
06  
08  
10  
12  
14  
16  
5" inlet (350 cfm)  
6" inlet (500 cfm)  
8" inlet (900 cfm)  
10" inlet (1400 cfm)  
12" inlet (2000 cfm)  
14" inlet (3000 cfm)  
16" inlet (4000 cfm)  
DA Stat = Direct-acting pneumatic t-stat  
(by others)  
RA Stat = Reverse-acting pneumatic t-stat  
(by others)  
Digit 20—Not Used  
0
N/A  
Digit 21—Not Used  
N/A  
Digit 22—Not Used  
N/A  
Digit 23—Transformer  
0
PN =  
FM =  
Pneumatic  
Factory installation of customer-  
supplied controller  
Digit 9—Not Used  
N/A  
Digit 10, 11—Design Sequence  
C0 Third (factory assigned)  
0
PVR =  
PneumaticVolume Regulator  
0
0
1
2
3
4
5
6
7
None  
Digit 16—Insulation  
120/24 volt (50VA)  
208/24 volt (50VA)  
240/24 volt (50VA)  
277/24 volt (50VA)  
480/24 volt (50VA)  
347/24 volt (50VA)  
575/24 volt (50VA)  
A
B
C
D
F
1/2" Matte-faced  
1" Matte-faced  
1/2" Foil-faced  
1" Foil-faced  
1" Double-wall  
3/8" Closed-cell  
Digit 12, 13, 14, 15—Controls  
ENON No Controls, Field-installed  
DDC/Electric  
PNON No Controls, Field-installed  
Pneumatic  
DD00 Trane elec actuator only  
DD01 DDC – Cooling only  
DD08 DDC – Constant-volume  
discharge  
DD11 LonTalk DDC Controller—  
Cooling only  
DD18 LonTalk DDC Controller—  
ConstantVolume Discharge  
G
Digit 17—Not Used  
N/A  
Digit 18—Not Used  
N/A  
Digit 24—Disconnect Switch  
0
0
W
None  
WithToggle  
0
Digit 25—Power Fuse  
0
W
None  
With  
6
VAV-SVN01E-EN  
Service Model  
Number Description  
Fan-Powered Parallel Units  
Digit 1, 2—UnitType  
Digit 20—Attenuator  
DD15 LonTalk DDC Controller w/  
pulse-width modulation electric heat  
control  
DD17 LonTalk DDC Controller w/ N.O.  
on/off hot water control  
FM00 FM customer actuator & control  
FM01 FMTrane actuator w/ customer-  
supplied controller  
VMA2 FM Johnson Controls  
VMA-1420  
PWR1 FM Seimens 540-100 w/  
GDE131.1P actuator  
PWR4 FM Seimens 540-100 w/Trane  
actuator  
PWR5 FM Seimens 540-100 w/  
GDE131.1U actuator  
0
W
None  
With  
VP  
VariTrane fan-powered parallel  
Digit 3—Reheat  
Digit 21—Water Coil  
C
Cooling Only  
0
1
2
3
4
5
6
None  
E
Electric Heat  
1-Row–Plenum inlet installed RH  
2-Row–Plenum inlet installed RH  
1-Row–Discharge installed, LH  
1-Row–Discharge installed, RH  
2-Row–Discharge installed, LH  
2-Row–Discharge installed, RH  
W
HotWater Heat  
Digit 4—Development Sequence  
Sixth  
Digit 5, 6—PrimaryAirValve  
F
05  
06  
08  
10  
12  
14  
16  
5" inlet (350 max cfm)  
6" inlet (500 max cfm)  
8" inlet (900 max cfm)  
10" inlet (1400 max cfm)  
12" inlet (2000 max cfm)  
14" inlet (3000 max cfm)  
16" inlet (4000 max cfm)  
Digit 22—Electrical Connections  
L
R
Left  
Right  
Electrical Connections Note:Airflow  
hitting you in the face.  
AT01 FM Automated Logic U341V+  
AT02 FM Automated Logic U141V+  
EI05 Analog – fan-powered parallel  
with optional on/off reheat  
PN00 PN – N.O.Trane pneumatic  
actuator, R.A. stat  
Digit 7, 8—SecondaryAirValve  
00 N/A  
Digit 9—Fan  
Digit 23—Transformer  
0
N/A (provided as standard)  
Digit 24—Disconnect Switch  
P
02SQ fan (500 nominal cfm)  
0
W
None  
With  
PN05 PN – N.O. PVR, R.A. stat  
Q
R
S
T
03SQ fan (1100 nominal cfm)  
04SQ fan (1350 nominal cfm)  
05SQ fan (1550 nominal cfm)  
06SQ fan (1850 nominal cfm)  
07SQ fan (2000 nominal cfm)  
Notes:  
N.C. =  
N.O =  
Note: VPCF,VPWF Toggle Disconnect  
VPEF – Door Interlocking Power  
Disconnect  
Normally-closed  
Normally-opened  
U
DA Stat = Direct-acting pneumatic t-stat  
(by others)  
RA Stat = Reverse-acting pneumatic  
t-stat (by others)  
Digit 10, 11—Design Sequence  
Digit 25—Power Fuse  
J0  
Design Sequence (Factory  
0
W
None  
With  
assigned)  
PN =  
FM =  
Pneumatic  
Digit 12, 13, 14, 15—Controls  
ENON No controls, field-installed DDC  
or analog  
Digit 26—Electric HeatVoltage  
Factory installation of customer-  
supplied controller  
0
None  
A
B
C
D
E
F
208/60/1  
208/60/3  
240/60/1  
277/60/1  
480/60/1  
480/60/3  
347/60/1  
575/60/3  
380/50/3  
120/60/1  
PVR =  
PneumaticVolume Regulator  
ENCL ENON with controls enclosure  
PNON No controls, field-installed  
pneumatic  
DD00 Trane elec actuator only  
DD01 DDC – cooling only  
DD02 DDC – N.C. on/off water control  
DD03 DDC – prop hot water control  
DD04 DDC – on/off electric heat  
control  
Digit 16—Insulation  
A
B
C
D
F
1/2" Matte-faced  
1" Matte-faced  
1/2" Foil-faced  
1" Foil-faced  
1" Double-wall  
3/8" Closed-cell  
G
H
J
G
K
DD05 DDC – pulse-width modulation  
electric heat control  
Digit 17—MotorType  
Digit 27, 28, 29—Electric HeatVoltage  
D
E
PSC Motor  
High-efficiency motor (ECM)  
000  
050  
010  
015  
None  
DD07 DDC – N.O. on/off hot water  
control  
0.5 kW  
1.0 kW  
1.5 kW  
Digit 18—MotorVoltage  
DD11 LonTalk DDC Controller—  
1
2
3
4
5
115/60/1  
277/60/1  
347/60/1  
208/60/1  
230/50/1  
Cooling  
only  
DD12 LonTalk DDC Controller w/ N.C.  
on/off hot water control  
260  
26.0 kW  
DD13 LonTalk DDC Controller w/  
proportional hot water control  
DD14 LonTalk DDC Control–on/off  
electric heat control  
Electric HeatVoltage Notes:  
Digit 19—Outlet Connection  
0.5 to 8.0 kW–½ kW increments  
8.0 to 18.0 kW –1 kW increments  
18.0 to 46.0 kW–2 kW increments  
1
2
Flanged  
Slip & Drive  
VAV-SVN01E-EN  
7
Service Model  
Number Description  
Fan-Powered Parallel Units (con't)  
Digit 30—Electric Heat Stages  
0
1
2
3
None  
1 Stage  
2 Stages Equal  
3 Stages Equal  
Digit 31—Contactors  
0
1
2
3
4
None  
24-volt magnetic  
24-volt mercury  
PE with magnetic  
PE with mercury  
Digit 32—Airflow Switch  
0
W
None  
With  
8
VAV-SVN01E-EN  
Service Model  
Number Description  
Fan-Powered Series Units  
Digit 1, 2—UnitType  
Digit 18—MotorVoltage  
DD13 LonTalk DDC Controller w/  
proportional hot water control  
DD14 LonTalk DDC Controller–on/off  
electric heat control  
DD15 LonTalk DDC Controller w/  
pulse-width modulation electric  
heat control  
DD17 LonTalk DDC Controller w/ N.O.  
on/off hot water control  
FM00 FM customer actuator & control  
FM01 FMTrane actuator w/ customer-  
supplied controller  
VMA2 FM Johnson controlsVMA-1420  
PWR1 FM Seimens 540-100 w/  
GDE131.1P actuator  
PWR4 FM Seimens 540-100 w/Trane  
actuator  
PWR5 FM Seimens 540-100 w/  
GDE131.1U actuator  
AT01 FM Automated Logic U341V+  
AT02 FM Automated Logic U141V+  
EI71 Analog fan-powered series  
with optional on/off reheat  
1
2
3
4
5
115/60/1  
277/60/1  
347/60/1  
208/60/1  
230/50/1  
VS  
VariTrane fan-powered series  
Digit 3—Reheat  
C
Cooling Only  
E
Electric Heat  
W
HotWater Heat  
Digit 19—Outlet Connection  
Digit 4—Development Sequence  
Sixth  
Digit 5, 6—PrimaryAirValve  
1
2
Flanged  
Slip & Drive  
F
Digit 20—Attenuator  
04  
05  
06  
08  
10  
12  
14  
16  
4" inlet (225 max cfm)  
5" inlet (350 max cfm)  
6" inlet (500 max cfm)  
8" inlet (900 max cfm)  
10" inlet (1400 max cfm)  
12" inlet (2000 max cfm)  
14" inlet (3000 max cfm)  
16" inlet (4000 max cfm)  
0
W
None  
With  
Digit 21—Water Coil  
0
3
4
5
6
None  
1-Row–Discharge installed, LH  
1-Row–Discharge installed, RH  
2-Row–Discharge installed, LH  
2-Row–Discharge installed, RH  
Digit 7, 8—SecondaryAirValve  
00 N/A  
Digit 9—Fan  
Digit 22—Electrical Connections  
L
R
Left  
Right  
P
02SQ fan (700 nominal cfm)  
PN00 PN – N.O.Trane pneumatic  
actuator, R.A. stat  
PN51 PN – N.O. PVR, duct pressure  
switch, R.A. stat  
PN52 PN – N.O. PVR, dual pressure  
main, R.A. stat  
Q
R
S
T
03SQ fan (1200 nominal cfm)  
04SQ fan (1550 nominal cfm)  
05SQ fan (1900 nominal cfm)  
06SQ fan (2600 nominal cfm)  
07SQ fan (3000 nominal cfm)  
Water Coil and Electrical Connections  
Note:Airflow hitting you in the face.  
Digit 23—Transformer  
U
0
N/A (provided as standard)  
Fan Note: See fan curves for specific  
airflows  
Digit 24—Disconnect Switch  
Notes:  
N.C. =  
N.O. =  
0
W
None  
With  
Normally-closed  
Normally-opened  
Digit 10, 11—Design Sequence  
Note: VSCF,VSWF Toggle Disconnect  
VSEF – Door Interlocking Power  
Disconnect  
DA Stat = Direct-acting pneumatic t-stat  
(by others)  
RA Stat = Reverse-acting pneumatic t-stat  
(by others)  
J0  
Design Sequence  
(Factory assigned)  
Digit 12, 13, 14, 15—Controls  
ENON No controls, field-installed DDC  
or analog  
Digit 25—Power Fuse  
PN =  
FM =  
Pneumatic  
0
W
None  
With  
Factory installation of customer-  
supplied controller  
ENCL ENON with control enclosure  
PNON No controls, field-installed  
pneumatic  
DD00 Trane elec actuator only  
DD01 DDC – cooling only  
DD02 DDC – N.C. on/off water control  
DD03 DDC – prop hot water control  
DD04 DDC – on/off electric heat  
control  
DD05 DDC – pulse-width modulation  
electric heat control  
DD07 DDC N.O. on/off hot water  
control  
PVR =  
PneumaticVolume Regulator  
Digit 26—Electric HeatVoltage  
0
None  
Digit 16—Insulation  
A
B
C
D
E
F
208/60/1  
208/60/3  
240/60/1  
277/60/1  
480/60/1  
480/60/3  
347/60/1  
575/60/3  
380/50/3  
120/60/1  
A
B
C
D
F
1/2" Matte-faced  
1" Matte-faced  
1/2" Foil-faced  
1" Foil-faced  
1" Double-wall  
3/8" Closed-cell  
G
G
H
J
Digit 17—MotorType  
D
E
PSC Motor  
High-efficiency motor (ECM)  
K
DD11 LonTalk DDC Controller—  
Cooling only  
DD12 LonTalk DDC Controller w/ N.C.  
on/off hot water control  
VAV-SVN01E-EN  
9
Service Model  
Number Description  
Fan-Powered Series Units (con't)  
Digit 27, 28, 29—Electric Heat Kilowatts  
000  
050  
010  
015  
None  
0.5 kW  
1.0 kW  
1.5 kW  
240  
24.0 kW  
Digit 30—Electric Heat Stages  
0
1
2
3
None  
1 Stage  
2 Stages Equal  
3 Stages Equal  
Digit 31—Contactors  
0
1
2
3
4
None  
24-volt magnetic  
24-volt mercury  
PE with magnetic  
PE with mercury  
Digit 32—Airflow Switch  
0
W
None  
With  
10  
VAV-SVN01E-EN  
Service Model  
Number Description  
Fan-Powered Low-Height Parallel Units  
Digit 1, 2—UnitType  
LP VariTrane fan-powered low-  
height parallel  
Digit 3—Reheat  
Digit 18—MotorVoltage  
DD14 LonTalk DDC Controller–on/off  
electric heat control  
1
2
3
5
115/60/1  
277/60/1  
347/60/1  
230/50/1  
DD15 LonTalk DDC Controller w/  
pulse-  
width modulation  
control  
electric heat  
DD17 LonTalk DDC Controller w/ N.O.  
on/off hot water control  
FM00 FM customer actuator & control  
FM01 FMTrane actuator w/ customer-  
supplied controller  
VMA2 FM Johnson ControlsVMA-  
1420  
PWR1 FM Seimens 540-100 w/  
GDE131.1P actuator  
PWR4 FM Seimens 540-100 w/Trane  
actuator  
PWR5 FM Seimens 540-100 w/  
GDE131.1U actuator  
C
Cooling Only  
Digit 19—Outlet Connection  
E
Electric Heat  
W
HotWater Heat  
1
2
Flanged  
Slip & Drive  
Digit 4—Development Sequence  
Sixth  
Digit 5, 6—PrimaryAirValve  
Digit 20—Not Used  
N/A  
Digit 21—Water Coil  
F
0
05  
06  
08  
RT  
5" inlet (350 maximum cfm)  
6" inlet (500 maximum cfm)  
8" inlet (900 maximum cfm)  
8" x 14" inlet (1800 maximum cfm)  
0
1
2
3
4
5
6
None  
1-Row–Plenum inlet installed  
2-Row–Plenum inlet installed  
1-Row–Discharge installed, LH  
1-Row–Discharge installed, RH  
2-Row–Discharge installed, LH  
2-Row–Discharge installed, RH  
Digit 7, 8—Secondary AirValve  
00 N/A  
Digit 9—Fan  
V
W
X
Digit 10, 11—Design Sequence  
K0 Sixth (factory assigned)  
Digit 12, 13, 14, 15—Controls  
AT01 FM Automated Logic U341V+  
AT02 FM Automated Logic U141V+  
EI05 Analog – fan-powered parallel  
with optional on/off reheat  
PN00 PN – N.O.Trane pneumatic  
actuator, R.A. stat  
08SQ 500 nominal cfm  
09SQ 900 nominal cfm  
10SQ 1800 nominal cfm  
Digit 22—Electrical Connections  
Left (airflow hitting you in the face)  
Digit 23—Transformer  
L
0
N/A (provided as standard)  
Digit 24—Disconnect Switch  
PN05 PN – N.O. PVR, R.A. stat  
0
W
None  
With  
ENON No controls, field-installed DDC/  
electric  
PNON No controls, field-installed  
pneumatic  
Notes:  
N.C. =  
N.O. =  
Normally-closed  
Normally-opened  
Note: LPCF, LPWF –Toggle Disconnect  
LPEF – Door Interlocking Power  
Disconnect  
DA Stat = Direct-acting pneumatic t-stat  
(by others)  
RA Stat = Reverse-acting pneumatic t-stat  
(by others)  
PN =  
FM =  
DD00 Trane elec actuator only  
DD01 DDC – cooling only  
DD02 DDC – N.C. on/off water valve  
control  
DD03 DDC – prop hot water valve  
control  
Digit 25—Power Fuse  
0
W
None  
With  
Pneumatic  
Factory installation of customer-  
supplied controller  
Digit 26—Electric HeatVoltage  
DD04 DDC – on/off electric heat control  
DD05 DDC – pulse-width modulation  
control  
DD07 DDC – N.O. on/off water valve  
control  
DD11 LonTalk DDC Controller—Cooling  
only  
DD12 LonTalk DDC Controller w/ N.C.  
on/off hot water control  
DD13 LonTalk DDC Controller w/  
proportional hot water control  
PVR =  
PneumaticVolume Regulator  
0
None  
A
B
C
D
E
F
208/60/1  
208/60/3  
240/60/1  
277/60/1  
480/60/1  
480/60/3  
347/60/1  
575/60/3  
380/50/3  
Digit 16—Insulation  
A
B
C
D
F
1/2" Matte-faced  
1" Matte-faced  
1/2" Foil-faced  
1" Foil-faced  
1" Double-wall  
3/8" Closed-cell  
G
H
J
G
Digit 17—MotorType  
D
E
PSC Motor  
High-efficiency motor (ECM)  
VAV-SVN01E-EN  
11  
Service Model  
Number Description  
Fan-Powered Low-Height Parallel Units (con't)  
Digit 27, 28, 29—Electric HeatVoltage  
Digit 30—Electric Heat Stages  
000  
005  
010  
015  
020  
025  
030  
035  
040  
045  
050  
055  
060  
065  
070  
075  
080  
090  
100  
110  
None  
0
1
2
None  
0.5 kW  
1.0 kW  
1.5 kW  
2.0 kW  
2.5 kW  
3.0 kW  
3.5 kW  
4.0 kW  
4.5 kW  
5.0 kW  
5.5 kW  
6.0 kW  
6.5 kW  
7.0 kW  
7.5 kW  
8.0 kW  
9.0 kW  
10.0 kW  
11.0 kW  
12.0 kW  
13.0 kW  
14.0 kW  
1 Stage  
2 Stages Equal  
Digit 31—Contactors  
0
1
2
3
4
None  
24-volt magnetic  
24-volt mercury  
PE with magnetic  
PE with mercury  
Digit 32—Airflow Switch  
0
W
None  
With  
120  
130  
140  
12  
VAV-SVN01E-EN  
Service Model  
Number Description  
Fan-Powered Low-Height Series Units  
Digit 1, 2—UnitType  
Digit 17—MotorType  
DD14 LonTalk DDC Controller–on/off  
electric heat control  
LS  
VariTrane low-height series fan-  
D
E
PSC Motor  
High-efficiency motor (ECM)  
powered  
DD15 LonTalk DDC Controller w/  
pulse-width modulation electric  
heat control  
DD17 LonTalk DDC Controller w/ N.O.  
on/off hot water control  
FM00 FM customer actuator & control  
FM01 FMTrane actuator w/ customer-  
supplied controller  
VMA2 FM Johnson controlsVMA-1420  
PWR1 FM Seimens 540-100 w/  
GDE131.1P actuator  
PWR4 FM Seimens 540-100Trane  
actuator  
PWR5 FM Seimens 540-100 w/  
GDE131.1U actuator  
AT01 FM Automated Logic U341V+  
AT02 FM Automated Logic U141V+  
EI71 Analog – Series fan-powered  
on/off reheat  
PN00 PN – N.O.Trane pneumatic  
actuator, R.A. stat  
Digit 3—Reheat  
Digit 18—MotorVoltage  
C
E
W
Cooling Only  
1
2
3
5
115/60/1  
277/60/1  
347/60/1  
230/50/1  
Electric Heat  
HotWater Heat  
Digit 4—Development Sequence  
Sixth  
Digit 5, 6—PrimaryAirValve  
Digit 19—Outlet Connection  
F
1
2
Flanged  
Slip & Drive  
05  
06  
08  
RT  
5" inlet (350 cfm)  
Digit 20—Not Used  
N/A  
Digit 21—Water Coil  
6" inlet (500 cfm)  
8" inlet (900 cfm)  
0
(8" x 14" inlet (1800 cfm)  
Digit 7, 8—SecondaryAirValve  
00 N/A  
Digit 9—Fan  
V
W
X
Digit 10, 11—Design Sequence  
K0 Sixth (factory assigned)  
Digit 12, 13, 14, 15—Controls  
ENON No controls, field-installed DDC/  
electric  
PNON No controls, field-installed  
pneumatic  
DD00 Trane elec actuator only  
DD01 DDC – cooling only  
DD02 DDC – N.C. on/off water valve  
control  
DD03 DDC – prop hot water valve  
control  
DD04 DDC – on/off electric heat  
control  
DD05 DDC – pulse-width modulation  
control  
0
3
4
5
6
None  
1-Row–Discharge installed, LH  
1-Row–Discharge installed, RH  
2-Row–DIscharge installed, LH  
2-Row–Discharge installed, RH  
08SQ 500 nominal cfm  
09SQ 900 nominal cfm  
10SQ 1800 nominal cfm  
Digit 22—Electrical Connections  
L
R
Left (airflow hitting you in the face)  
Right (airflow hitting you in the face)  
PN51 PN – N.O. PVR, duct pressure  
switch, R.A. stat  
PN52 PN – N.O. PVR, dual pressure  
main, R.A. stat  
Digit 23—Transformer  
0
N/A (provided as standard)  
Digit 24—Disconnect Switch  
Notes:  
N.C. =  
N.O. =  
0
W
None  
With  
Normally-closed  
Normally-opened  
Note: LSCF, LSWF –Toggle Disconnect  
LSEF – Door Interlocking Power  
Disconnect  
DA Stat = Direct-acting pneumatic t-stat  
(by others)  
RA Stat = Reverse-acting pneumatic  
t-stat (by others)  
PN =  
FM =  
Digit 25—Power Fuse  
Pneumatic  
0
W
None  
With  
Factory installation of customer-  
supplied controller  
Digit 26—Electric HeatVoltage  
PVR =  
PneumaticVolume Regulator  
0
None  
Digit 16—Insulation  
A
B
C
D
E
F
208/60/1  
208/60/3  
240/60/1  
277/60/1  
480/60/1  
480/60/3  
347/60/1  
575/60/3  
380/50/3  
DD07 DDC – N.O. on/off water valve  
control  
A
B
C
D
F
1/2" Matte-faced  
1" Matte-faced  
1/2" Foil-faced  
1" Foil-faced  
1" Double-wall  
3/8" Closed-cell  
DD11 LonTalk DDC Controller—  
Cooling only  
DD12 LonTalk DDC Controller w/ N.C.  
on/off hot water control  
DD13 LonTalk DDC Controller w/  
proportional hot water control  
G
G
H
J
VAV-SVN01E-EN  
13  
Service Model  
Number Description  
Fan-Powered Low-Height Series Units (con't)  
Digit 27, 28, 29—Electric HeatVoltage  
Digit 30—Electric Heat Stages  
000  
005  
010  
015  
020  
025  
030  
035  
040  
045  
050  
055  
060  
065  
070  
075  
080  
090  
100  
110  
None  
0
1
2
None  
0.5 kW  
1.0 kW  
1.5 kW  
2.0 kW  
2.5 kW  
3.0 kW  
3.5 kW  
4.0 kW  
4.5 kW  
5.0 kW  
5.5 kW  
6.0 kW  
6.5 kW  
7.0 kW  
1 Stage  
2 Stages Equal  
Digit 31—Contactors  
0
1
2
3
4
None  
24-Volt magnetic  
24-Volt mercury  
PE with magnetic  
PE with mercury  
Digit 32—Air Flow Switch  
0
W
None  
With  
7.5 kW  
8.0 kW  
9.0 kW  
10.0 kW  
11.0 kW  
12.0 kW  
13.0 kW  
14.0 kW  
15.0 kW  
16.0 kW  
17.0 kW  
18.0 kW  
120  
130  
140  
150  
160  
170  
180  
14  
VAV-SVN01E-EN  
General  
Information  
Literature Contents  
y Verify that all options have been  
included, such as filters, controls,  
heating coils, water valves, etc. Also  
check that the unit voltages agree with  
the building parameters.  
y If a discrepancy occurs between what  
was ordered and what is received,  
contact you localTrane representative  
immediately.  
This manual describes the installation  
ofVariTraneVAV units with recom-  
mended wiring, piping, and mounting  
of Single-Duct, Dual-Duct, Fan-Pow-  
ered, Low-Height terminal units and  
diffusers.  
y Read the appropriate section in this  
manual for installation procedures prior  
to actual starting of equipment.  
y Manually rotate the fan (if applicable) to  
assure that there are no obstructions  
within the housing.  
Receiving and Handling  
Upon receiving the equipment, please  
inspect each unit and components for  
external or internal damage. Refer to  
the bill of lading to insure all equipment  
and accessories have been received.  
Contact your localTrane sales  
representative and notify the trucking  
company immediately of any short ship  
or damaged equipment.  
VariTrane Units are shipped completely  
assembled with the exceptions of  
optional attenuators for fan-powered  
units and accessories.  
Upon receiving the equipment,  
complete the following:  
y Claims for in-transit damage must be  
filed immediately with the delivery  
carrier.  
y For hot water re-heat units, check the  
coil fins and make sure that coils are  
not damaged.  
y Locate the nameplate and refer to the  
model and sales order number and  
check that the correct units have been  
delivered.  
y Locate and verify that the correct zone  
sensors are with the order.These will be  
marked with an orange Accessories  
Enclosed” label. Store in a secure  
location until needed. Accessories lost  
at the jobsite are NOT covered by  
Tranes warranty.  
y Inspect the control enclosures and air  
valve casing for dents or punctures.  
NOTICE:  
Warnings and Cautions appear at appropriate sections throughout this manual.  
Read these carefully.  
Indicates a potentially hazardous situation which, if  
not avoided, could result in death or serious injury.  
WARNING  
– Indicates a potentially hazardous situation which, if  
not avoided, may result in minor or moderate injury. It may also be used  
to alert against unsafe practices.  
CAUTION  
Indicates a situation that may result in equipment or  
property-damage-only accidents.  
CAUTION  
VAV-SVN01E-EN  
15  
Unit  
Information  
Single-Duct Units  
Figure 1 Typical Single-Duct Units  
Dual-Duct Units  
The basic unit consists of a sheet metal  
casing with an air valve, which is used  
to modulate the air being delivered into  
the occupied zone.The unit is designed  
to modulate either cooling or heating  
air between the temperatures of 40°F  
and 140°F. Air enters the air valve  
through the round or rectangular inlet  
and exits into the sheet metal casing to  
be distributed to the zone either  
through integral round outlets in the  
casing or through rectangular duct  
attached to the discharge of the unit.  
The basic unit can also be ordered with  
factory-mounted electric or hot water  
heating coils attached to the discharge.  
(See Figure 1.)  
Dual-duct units provide two air valves:  
one as heating primary air and the  
other as cooling primary air. Both  
discharge into the common outlet,  
which leads to the zone being con-  
trolled. (See Figure 2.)  
The units are provided with a slip and  
drive rectangular duct connection or  
can be ordered with integral outlet  
plenum.  
Sequencing of the hot and cold air  
valve is dependent upon job  
requirements. One typical control is the  
valves working in conjunction with each  
other to respond to zone temperature.  
VCCF  
When the cooling valve becomes fully  
closed or reaches a specified minimum,  
then the heating valve will begin to  
modulate or vice versa.The typical  
result is that air flowing to the zone  
varies from the maximum down to a  
minimum and back up to a maximum  
as the load varies and as the controls  
would cause one air valve to close and  
the other to open.  
These re-heat units are used primarily  
to reheat air-to-zone temperature when  
the load in the occupied space is low.  
Primary air is modulated through the  
VariTrane air valve by rotating the  
damper blade. All air valves have a  
round/rectangular inlet for easy fit-up  
with incoming ductwork.  
Another typical application is when the  
unit provides a constant volume to the  
zone.When the zone sensor is tied  
directly to the heating valve, it will  
modulate the heating valve according  
to the zone temperature.  
VCWF  
When the heating valve is fully closed  
or there is a call for cooling in the zone,  
the cooling valve will be at constant  
supply. As the space becomes too cool,  
the heating valve will modulate open,  
decreasing the cooling valve flow.The  
typical result is that the air flowing into  
the zone stays at a constant flow  
VCEF  
whether the unit is heating or cooling.  
Figure 2 –Typical Dual-Duct Unit  
VDDF  
16  
VAV-SVN01E-EN  
Unit  
Information  
Fan-Powered and Fan-Powered  
Low-Height Units  
VariTrane fan-powered and low-height  
fan-powered units can be either parallel  
or series, with or without re-heat. (See  
Figure 3.)  
VariTrane fan-powered unit fan sizes  
02SQ–05SQ and 08SQ–10SQ were  
performance tested at .12 in. w.g. and  
sizes 06SQ and 07SQ were tested at .15  
in. w.g. Units are not designed to  
operate unducted and below these  
tested static pressures.  
The fan on a series unit runs  
continuously whenever the main air  
handler unit is in operation.There are  
various options for starting the fan.The  
fan can be started three ways: 1)  
remotely, 2) by a duct pressure switch,  
or 3) by a combination of both.The  
particular fan control method may vary  
from unit to unit, depending upon job  
needs.  
Note: Fan-powered units are available  
with rectangular discharge connection  
only. The optional heater is mounted on  
the discharge of the unit. Hot water coils  
are connected to either the plenum inlet  
or on the discharge on parallel units, and  
to the discharge of series units.  
Figure 3 –Typical Fan-Powered Units  
Typically, the heater is off while the air  
valve modulates primary air and  
responds to zone temperature. If zone  
temperature decreases to the point  
where a decrease in primary air will not  
maintain the desired temperature, the  
re-heat will be activated to increase the  
temperature of the discharge air.  
On a parallel unit, theVariTrane air valve  
delivers primary cooling air to the unit  
outlet.When the space temperature  
decreases beyond air valve control, the  
fan is turned on as the first stage of  
heat.The fan delivers plenum air from  
above the occupied space to the unit  
outlet, which is mixed with primary air  
and delivered to the occupied space.  
VSCF  
VPCF  
Note: Either the fan, the air valve, or both  
can deliver airflow into the occupied  
space. In order to prevent primary airflow  
from exiting through the fan when the  
fan is not running on a parallel unit, a  
back draft damper is provided. When the  
fan is not running, the efficiency of this  
system is the same as a standard single-  
ductVAV unit.  
VSEF  
VPEF  
Typically, the control systems applied to  
parallel units cause the air valve to  
close to zero or a minimum flow before  
the fan is activated. After the fan is  
activated, the optional heat will be  
activated upon further reduction in  
zone temperature.Therefore, minimal  
primary air is mixed with the heated air.  
VPWF  
VSWF  
VAV-SVN01E-EN  
17  
Unit  
Installation  
Dual-Duct  
Due to their weight, theVAV terminal  
units should be suspended from the  
uppermost ceiling, independent of the  
false ceiling grid. Suspension devices  
are to be supplied by the installer. Units  
must be installed level and upright.  
Failure to level the unit properly may  
prevent proper operation of the  
controls and/or terminal unit. Units are  
not designed to be installed vertically.  
Consequently, this will also void the UL  
ratings and any warranty on the unit.  
Dual-duct units should be supported by  
either hanger straps or by using a  
threaded rod in conjunction with the  
hanger brackets that are provided on  
the unit. See Figure 5.  
Figure 5  
Dual-Duct Hanger Bracket Locations  
Single-Duct  
Depending upon the size and weight of  
the single-duct unit, it may be capable  
of being supported by the ductwork  
that is connected to it. No hanger  
brackets are provided on these units  
since the unit should be supported by  
means of a hanger strap.The hanger  
strap should be secured directly to the  
unit casing as shown in Figure 4.  
A
C
AIR  
VALVE  
COOLING  
AIR  
VALVE  
HEATING  
For cooling only single-duct units or  
single-duct units with hot water coil, the  
unt may be rotated 180° for opposite  
side connections.  
B
For units with electric heat, the unit  
must be ordered from the factory  
designating either right- or left-hand  
connections.  
Figure 4  
TOP VIEW  
Single-Duct Hanging  
Recommendations  
A
B
C
Inlet Size  
5" thru 10"  
1.376" (35 mm)  
23.154" (588 mm)  
25.154" (639 mm)  
25.25" (641 mm)  
37.25" (946 mm)  
1.376" (35 mm)  
12" thru 16"  
18  
VAV-SVN01E-EN  
Unit  
Installation  
Fan-Powered (Standard and Low-  
Height)  
Figure 6  
Fan-powered units should be sup-  
ported by either hanger straps or by  
using a threaded rod in conjunction  
with the hanger brackets that are  
provided on the unit. Care should be  
exercised to insure that the hanging  
straps do not block the side access  
panel. See Figures 6–13.  
Parallel Hanger Bracket Locations Sizes  
C
Water  
Coil  
Airflow  
Plenum Inlet  
TOP VIEW  
Parallel Cooling & Hot Water  
B
Primary  
Airflow  
Optional Attenuator  
Field Installed  
Flow Ring  
Tubing  
F
E
Air  
Valve  
D
A
Airflow  
Discharge Outlet  
A
B
C
D
E
F
FAN SIZE  
41.154" (1041 mm)  
38.95" (989 mm)  
26.75" (679 mm) 26.75" (679 mm)  
3.25" (83 mm) 20.00" (508 mm)  
02SQ  
26.75" (679 mm)  
3.25" (83 mm)  
20.00" (508 mm) 38.95" (989 mm)  
03SQ, 04SQ, 05SQ 29.75" (756 mm)  
41.154" (1041 mm)  
36.75" (933 mm) 26.75" (679 mm) 41.154" (1041 mm) 3.25" (83 mm) 20.00" (508 mm) 38.95" (989 mm)  
06SQ, 07SQ  
C
Airflow  
Plenum Inlet  
B
Optional Attenuator  
Field Installed  
Primary  
Airflow  
Flow Ring  
Tubing  
F
E
Air  
TOP VIEW  
Valve  
Parallel Electric Heat  
D
A
Heater  
Airflow  
Discharge Outlet  
43.546  
(1106 mm)  
VAV-SVN01E-EN  
19  
Unit  
Installation  
Figure 7  
Series Hanger Bracket Locations  
A
B
Flow Ring  
Tubing  
C
Air  
Valve  
Optional Attenuator  
Field Installed  
Airflow  
Plenum Inlet  
TOP VIEW  
Series Cooling & Hot Water  
E
D
2.  
1.  
Fan Inlet w/o  
Attenuator  
1.  
All attenuators are the same length and width.  
2.  
Sizes 01 and 02 units are smaller than attenuators.  
Water  
Coil  
1.625"  
(41 mm)  
F
A
B
C
D
41.154" (1041 mm)  
E
35.154 (740 mm)  
FAN SIZE  
02SQ  
(Elec. Heat Only)  
18.75" (476 mm)  
3.25" (83 mm)  
20.132" (511 mm)  
26.75" (679 mm)  
03SQ, 04SQ 20.75" (527 mm)  
05SQ 27.25" (692 mm)  
26.75" (679 mm) 3.25" (83 mm) 41.154" (1041 mm) 41.154" (1041 mm) 23.875 (606 mm)  
41.154" (1041 mm)  
26.75" (679 mm) 3.25" (83 mm)  
41.154" (1041 mm) 29.875" (759 mm)  
06SQ, 07SQ 27.25" (692 mm)  
26.75" (679 mm) 3.25" (83 mm) 41.154" (1041 mm) 41.154" (1041 mm) 29.875" (759 mm)  
Flow Ring  
Tubing  
A
B
C
Air  
Valve  
Optional Attenuator  
Field Installed  
TOP VIEW  
Series Electric Heat  
Airflow  
Plenum Inlet  
D
G
Fan Inlet w/o  
Attenuator  
Electric  
Heater  
C
19.00"  
B
(483 mm)  
F
20  
VAV-SVN01E-EN  
Unit  
Installation  
Figure 8  
Low-Height Parallel 08SQ/09SQ w/ Hot Water or Electric Heat  
31.65"  
(804 mm)  
Airflow  
Plenum Inlet  
13.00"  
(330 mm)  
23.90"  
(607 mm)  
Primary  
Airflow  
19.86"  
(504 mm)  
Optional Attenuator  
Field Installed  
24.30"  
(617 mm)  
3.35"  
(85 mm)  
Airflow  
Discharge Outlet  
TOP VIEW  
23.10"  
13.80"  
4.00"  
(587 mm)  
(350 mm)  
(102 mm)  
31.65"  
(804 mm)  
Airflow  
Plenum Inlet  
23.90"  
(607 mm)  
13.00"  
(330 mm)  
Primary  
Airflow  
19.86"  
(504 mm)  
Optional Attenuator  
Field Installed  
24.30"  
(617 mm)  
Heater  
3.35"  
(85 mm)  
TOP VIEW  
Airflow  
Discharge Outlet  
23.10"  
(587 mm)  
3.00"  
(76 mm)  
13.80"  
(350 mm)  
4.00"  
(102 mm)  
VAV-SVN01E-EN  
21  
Unit  
Installation  
Figure 9  
Low-Height Parallel10SQ  
1.625"  
(41 mm)  
38.95"  
(989 mm)  
Primary  
Airflow  
Flow Ring  
Tubing  
Plenum  
Inlet  
Air  
Valve  
5.625"  
(143 mm)  
38.75"  
(984 mm)  
5.625"  
(143 mm)  
Terminal Box  
Optional Heater  
Airflow  
Discharge Outlet  
41.137"  
(1045 mm)  
TOP VIEW  
22  
VAV-SVN01E-EN  
Unit  
Installation  
Figure 10  
Low-Height Series 08SQ/09SQ w/ Hot Water or Electric Heat  
31.65"  
(804 mm)  
Airflow  
Plenum Inlet  
10.13"  
(257 mm)  
12.85"  
(326 mm)  
4.00"  
(102 mm)  
Primary  
Airflow  
19.86"  
(504 mm)  
Optional Attenuator  
Field Installed  
Air  
Valve  
3.35"  
(85 mm)  
34.30"  
(871 mm)  
31.65"  
(804 mm)  
3.35"  
10.13"  
(257 mm)  
(85 mm)  
Airflow  
Plenum Inlet  
12.85"  
(326 mm)  
4.00"  
(102 mm)  
Water  
Coil  
Primary  
Airflow  
TOP VIEW  
Optional Attenuator  
Field Installed  
19.86"  
(504 mm)  
Air  
Valve  
Airflow  
3.35"  
(85 mm)  
20.00"  
(508 mm)  
27.00"  
(686 mm)  
34.30"  
(871 mm)  
3.35"  
(85 mm)  
Optional  
Electric Heater  
TOP VIEW  
Airflow  
20.00"  
(508 mm)  
27.00"  
(686 mm)  
VAV-SVN01E-EN  
23  
Unit  
Installation  
Figure 11  
Low-Height Series 10SQ w/ Hot Water or Electric Heat  
19.45"  
(494 mm)  
19.45"  
(494 mm)  
10.12"  
(257 mm)  
31.65"  
31.65"  
(804 mm)  
(804 mm)  
Optional Attenuator  
Field Installed  
Optional Attenuator  
Field Installed  
Primary  
Airflow  
19.86"  
(504 mm)  
19.86"  
(504 mm)  
Airflow  
Plenum Inlet  
Airflow  
Plenum Inlet  
3.35"  
(85 mm)  
30.30"  
(770 mm)  
3.35"  
(85 mm)  
TOP VIEW  
Airflow  
Discharge Outlet  
42.00"  
(1067 mm)  
3.50"  
(89 mm)  
3.50"  
(89 mm)  
19.45"  
(494 mm)  
19.45"  
(494 mm)  
10.12"  
(257 mm)  
31.65"  
(804 mm)  
31.65"  
(804 mm)  
Optional Attenuator  
Field Installed  
Optional Attenuator  
Field Installed  
Primary  
Airflow  
19.86"  
(504 mm)  
19.86"  
(504 mm)  
Airflow  
Plenum Inlet  
3.35"  
(85 mm)  
Airflow  
Plenum Inlet  
30.30"  
(770 mm)  
3.35"  
(85 mm)  
Plenum Area  
TOP VIEW  
Optional  
Heater  
1.92"  
(49 mm)  
Airflow  
Discharge Outlet  
42.00"  
(1067 mm)  
3.50"  
(89 mm)  
3.50"  
(89 mm)  
24  
VAV-SVN01E-EN  
Unit  
Installation  
Figure 12  
Attenuator Installation—Parallel Units  
1. Attach attenuator to unit as shown with provided mounting brackets.  
MOUNTING BRACKET  
OPTIONAL ATTENUATOR  
FIELD INSTALLED  
Note: Bottom bracket not shown. Bottom bracket to be installed in same orientation on  
bottom of unit.  
VAV-SVN01E-EN  
25  
Unit  
Installation  
Figure 13  
Attenuator Installation—Series Units  
1. Attach attenuator to unit as shown with provided mounting brackets.  
MOUNTING BRACKET  
OPTIONAL ATTENUATOR  
FIELD INSTALLED  
Note: Bottom bracket not shown. Bottom bracket to be installed in same  
orientation on bottom of unit.  
26  
VAV-SVN01E-EN  
Unit  
Installation  
Figure 14  
Attenuator Installation—Low-Height Parallel Units  
1. Attach attenuator to unit as shown with provided mounting brackets.  
MOUNTING BRACKET  
OPTIONAL ATTENUATOR  
FIELD INSTALLED  
Note: Bottom bracket not shown. Bottom bracket to be installed in  
same orientation on bottom of unit.  
VAV-SVN01E-EN  
27  
Unit  
Installation  
Figure 15  
Attenuator Installation—Low-Height Series Units  
1. Attach attenuator to unit as shown with provided mounting brackets.  
MOUNTING BRACKET  
OPTIONAL ATTENUATOR  
FIELD INSTALLED  
MOUNTING BRACKET  
OPTIONAL ATTENUATOR  
FIELD INSTALLED  
OPTIONAL ATTENUATOR  
FIELD INSTALLED  
MOUNTING BRACKET  
Note: Bottom bracket not shown. Bottom bracket to be installed in same orientation on bottom of unit.  
28  
VAV-SVN01E-EN  
Unit  
Installation  
Chart 1 – UnitWeights  
Single-Duct Units  
Unit  
Size  
VCCF  
VCCF w/  
DualWall  
(lbs/kg)  
VCEF  
VCEF w/  
DualWall  
(lbs/kg)  
VCWF  
1-Row  
(lbs/kg)  
VCWF  
2-Row  
(lbs/kg)  
VCWF 1-Row  
w/ DualWall  
(lbs/kg)  
VCWF 2-Row  
w/ DualWall  
(lbs/kg)  
(lbs/kg)  
(lbs/kg)  
4
5
6
8
16/7  
16/7  
16/7  
16/7  
19/9  
19/9  
19/9  
20/9  
38/17  
38/17  
38/17  
38/17  
48/22  
48/22  
48/22  
49/22  
21/10  
21/10  
21/10  
21/10  
22/10  
22/10  
22/10  
24/11  
24/11  
24/11  
24/11  
25/11  
25/11  
25/11  
25/11  
28/13  
10  
12  
14  
16  
24  
22/10  
27/12  
32/15  
35/16  
52/24  
27/12  
34/15  
41/19  
46/21  
63/29  
46/21  
52/24  
60/27  
69/31  
84/38  
60/27  
68/31  
80/36  
91/41  
106/48  
29/13  
37/17  
44/20  
49/22  
70/32  
32/15  
40/18  
48/22  
54/24  
77/35  
34/15  
43/20  
53/24  
60/27  
81/37  
37/17  
47/21  
57/26  
65/29  
88/40  
Dual-Duct Units  
Unit  
Size  
VDDF  
VDDF w/  
DualWall  
(lbs/kg)  
Unit  
Size  
VDDF  
VDDF w/  
DualWall  
(lbs/kg)  
(lbs/kg)  
(lbs/kg)  
0505  
0506  
0606  
0508  
54/24  
54/24  
54/24  
55/25  
68/31  
68/31  
68/31  
68/31  
1012  
1212  
0814  
1014  
59/27  
60/27  
78/35  
79/36  
72/33  
84/38  
102/46  
103/47  
0608  
0510  
0808  
0610  
55/25  
56/25  
56/25  
56/25  
69/31  
69/31  
70/32  
70/32  
1214  
1414  
0816  
1016  
80/36  
81/37  
79/36  
80/36  
104/47  
105/48  
103/47  
104/47  
0810  
1010  
0612  
0812  
57/26  
61/28  
57/26  
58/26  
70/32  
74/34  
70/32  
71/32  
1216  
1416  
1616  
81/37  
82/37  
83/38  
105/48  
105/48  
106/48  
Parallel Fan-Powered Units  
Unit  
Size  
VPCF VPCF w/  
DualWall  
VPEF  
VPEF w/  
DualWall  
(lbs/kg)  
VPWF  
1-Row  
(lbs/kg)  
VPWF  
2-Row  
(lbs/kg)  
VPWF 1-Row  
w/ DualWall  
(lbs/kg)  
VPWF 2-Row  
w/ DualWall  
(lbs/kg)  
VPxF  
Attenuator  
(lbs/kg)  
(lbs/kg) (lbs/kg)  
(lbs/kg)  
0502SQ  
0602SQ  
0603SQ  
0802SQ  
81/37  
80/36  
83/38  
81/37  
115/52  
114/52  
117/53  
115/52  
110/550  
109/49  
112/51  
110/50  
144/65  
143/65  
146/66  
144/65  
92/42  
91/41  
105/48  
92/42  
95/43  
94/43  
108/49  
95/43  
126/57  
125/57  
139/63  
126/57  
129/59  
128/58  
142/64  
129/59  
46/21  
46/21  
48/22  
46/21  
0803SQ  
0804SQ  
1002SQ  
1003SQ  
83/38  
84/38  
82/37  
84/38  
117/53  
118/54  
116/53  
118/54  
112/51  
113/51  
111/50  
113/51  
146/66  
147/67  
145/66  
147/67  
105/48  
106/48  
93/42  
108/49  
109/49  
96/44  
139/63  
140/64  
127/58  
140/64  
142/64  
143/65  
130/59  
143/65  
48/22  
48/22  
46/21  
48/22  
106/48  
109/49  
1004SQ  
1005SQ  
1006SQ  
1007SQ  
85/39  
98/44  
114/52  
122/55  
119/54  
132/60  
148/67  
156/71  
114/52  
128/58  
144/65  
152/69  
148/67  
162/73  
178/81  
186/84  
107/49  
120/54  
127/58  
135/61  
110/50  
123/56  
130/59  
138/63  
141/64  
154/70  
161/73  
169/77  
144/65  
157/71  
164/74  
172/78  
48/22  
48/22  
54/24  
54/24  
1203SQ  
1204SQ  
1205SQ  
1206SQ  
85/39  
86/39  
99/45  
115/52  
119/54  
120/54  
133/60  
149/68  
114/52  
115/52  
129/59  
145/66  
148/67  
149/68  
163/74  
179/81  
107/49  
108/49  
121/55  
128/58  
110/50  
111/50  
124/56  
131/59  
141/64  
142/64  
155/70  
162/73  
144/65  
145/66  
158/72  
165/75  
48/22  
48/22  
48/22  
54/24  
1207SQ  
1404SQ  
1405SQ  
1406SQ  
123/56  
87/39  
100/45  
116/53  
157/71  
121/55  
134/61  
150/68  
153/69  
116/53  
130/59  
146/66  
187/85  
150/68  
164/74  
180/82  
136/62  
109/49  
122/55  
129/59  
139/63  
112/51  
125/57  
132/60  
170/77  
143/65  
156/71  
163/74  
173/78  
146/66  
159/72  
166/75  
54/24  
48/22  
48/22  
54/24  
1407SQ  
1606SQ  
1607SQ  
124/56  
117/53  
125/57  
158/72  
151/68  
159/72  
154/70  
147/67  
155/70  
188/85  
181/82  
189/86  
137/62  
130/59  
138/63  
140/64  
133/60  
141/64  
171/78  
164/74  
172/78  
174/79  
167/76  
175/79  
54/24  
54/24  
54/24  
VAV-SVN01E-EN  
29  
Unit  
Installation  
Chart 1 – UnitWeights (Con't.)  
Series Fan-Powered  
Unit  
VSCF VSCF w/ VSEF VSEF w/ VSWF  
VSWF VSWF 1-Row VSWF 2-Row  
VSxF  
Attenuator  
(lbs/kg)  
Size  
DualWall  
(lbs/kg) (lbs/kg)  
DualWall  
(lbs/kg)  
1-Row  
2-Row  
w/ DualWall  
(lbs/kg)  
w/ DualWall  
(lbs/kg)  
(lbs/kg)  
(lbs/kg)  
(lbs/kg)  
0402SQ  
0502SQ  
0602SQ  
0603SQ  
0604SQ  
78/35  
78/35  
77/35  
76/34  
87/39  
93/42  
93/42  
92/42  
100/45  
111/50  
104/47  
104/47  
103/47  
105/48  
116/53  
119/54  
119/54  
118/54  
129/59  
140/64  
85/39  
85/39  
84/38  
88/40  
99/45  
87/39  
87/39  
86/39  
92/42  
103/47  
100/45  
100/45  
99/45  
112/51  
123/56  
102/46  
102/46  
101/46  
116/53  
127/58  
46/21  
46/21  
46/21  
48/22  
48/22  
0802SQ  
0803SQ  
0804SQ  
1002SQ  
1003SQ  
79/36  
77/35  
88/40  
81/37  
80/36  
94/43  
101/46  
112/51  
96/44  
105/48  
106/48  
117/53  
107/49  
109/49  
120/54  
130/59  
141/64  
122/55  
133/60  
86/39  
89/40  
100/45  
88/40  
92/42  
88/40  
93/42  
104/47  
90/41  
96/44  
101/46  
113/51  
124/56  
103/47  
116/53  
103/47  
117/53  
128/58  
105/48  
120/54  
46/21  
48/22  
48/22  
46/21  
48/22  
104/47  
1004SQ  
1005SQ  
1006SQ  
1007SQ  
1203SQ  
91/41  
92/42  
104/47  
117/53  
82/37  
115/52  
116/53  
133/60  
146/66  
106/48  
120/54  
121/55  
135/61  
148/67  
111/50  
144/65  
145/66  
164/74  
177/80  
135/61  
103/47  
104/47  
119/54  
132/60  
94/43  
107/49  
108/49  
124/56  
137/62  
98/44  
127/58  
128/58  
148/67  
161/73  
118/54  
131/59  
132/60  
153/69  
166/75  
122/55  
48/22  
48/22  
54/24  
54/24  
48/22  
1204SQ  
1205SQ  
1206SQ  
1207SQ  
1404SQ  
92/42  
94/43  
105/48  
118/54  
93/42  
116/53  
118/54  
134/61  
147/67  
117/53  
121/55  
123/56  
136/62  
149/68  
122/55  
145/66  
147/67  
165/75  
178/81  
146/66  
104/47  
106/48  
120/54  
133/60  
105/48  
108/49  
110/50  
125/57  
13863  
109/49  
128/58  
130/59  
149/68  
162/73  
129/59  
132/60  
134/61  
154/70  
167/76  
133/60  
48/22  
48/22  
54/24  
54/24  
48/22  
1405SQ  
1406SQ  
1407SQ  
1606SQ  
1607SQ  
96/44  
106/48  
119/54  
107/49  
120/54  
120/54  
135/61  
148/67  
136/62  
149/68  
125/57  
137/62  
150/68  
138/63  
151/68  
149/68  
166/75  
179/81  
167/76  
180/82  
108/49  
121/55  
134/61  
122/55  
135/61  
112/51  
126/57  
139/63  
127/58  
140/64  
132/60  
150/68  
163/74  
151/68  
164/74  
136/62  
155/70  
168/76  
156/71  
169/77  
48/22  
54/24  
54/24  
54/24  
54/24  
Low-Height Parallel Units  
Unit  
LPCF LPCF w/ LPEF LPEF w/  
LPWF  
1-Row  
(lbs/kg)  
LPWF  
2-Row  
(lbs/kg)  
LPWF 1-Row LPWF 2-Row  
LPxF  
Attenuator  
(lbs/kg)  
Size  
DualWall  
(lbs/kg) (lbs/kg)  
DualWall  
(lbs/kg)  
w/ DualWall  
(lbs/kg)  
w/ DualWall  
(lbs/kg)  
(lbs/kg)  
0508SQ  
0608SQ  
0609SQ  
0808SQ  
69/31  
68/31  
73/33  
69/31  
89/40  
88/40  
93/42  
89/40  
84/38  
83/38  
88/40  
84/38  
104/47  
103/47  
108/49  
104/47  
78/35  
77/35  
82/37  
78/35  
81/37  
80/36  
85/39  
81/37  
98/44  
97/44  
102/46  
98/44  
101/46  
100/45  
105/48  
101/46  
10/5  
10/5  
10/5  
10/5  
0809SQ  
0810SQ  
74/34  
90/41  
14RT09SQ 83/38  
94/43  
110/50  
103/47  
117/53  
89/40  
105/48  
98/44  
109/49  
125/57  
118/54  
132/60  
83/38  
99/45  
92/42  
106/48  
86/39  
102/46  
95/43  
103/47  
119/54  
112/51  
126/57  
106/48  
122/55  
115/52  
129/59  
10/5  
10/5  
10/5  
10/5  
14RT10SQ 97/44  
112/51  
109/49  
Low-Height Series Units  
Unit  
Size  
LSCF LSCF w/  
DualWall  
LSEF  
LSEF w/  
DualWall  
(lbs/kg)  
LSWF  
1-Row  
(lbs/kg)  
LSWF  
2-Row  
(lbs/kg)  
LSWF 1-Row  
w/ DualWall  
(lbs/kg)  
LSWF 2-Row  
w/ DualWall  
(lbs/kg)  
LSxF  
Attenuator  
(lbs/kg)  
(lbs/kg) (lbs/kg)  
(lbs/kg)  
0508SQ  
0608SQ  
0609SQ  
0808SQ  
71/32  
70/32  
80/36  
71/32  
86/39  
85/39  
95/43  
86/39  
86/39  
85/39  
95/43  
86/39  
101/45  
100/45  
110/50  
101/46  
80/36  
79/36  
89/40  
80/36  
82/37  
81/37  
91/41  
82/37  
95/43  
94/43  
104/47  
95/43  
97/44  
96/44  
106/48  
97/44  
10/5  
10/5  
10/5  
10/5  
0809SQ  
0810SQ  
81/37  
95/43  
14RT09SQ 90/41  
96/44  
120/54  
105/48  
130/59  
96/44  
120/54  
105/48  
130/59  
111/50  
145/66  
120/54  
155/70  
90/41  
111/50  
99/45  
92/42  
115/52  
101/46  
125/57  
105/48  
136/62  
114/52  
146/66  
107/49  
140/64  
116/53  
150/68  
10/5  
20/9  
10/5  
20/9  
14RT10SQ 105/48  
121/55  
30  
VAV-SVN01E-EN  
Unit  
Installation  
Duct Connections  
Care should be taken to properly  
support the water coil piping  
connections while connecting the  
adjoining pipe.  
Actuator Mounting  
AllVariTrane units should be provided  
with a minimum of 1.5-duct diameters  
of straight duct prior to the inlet of the  
unit. It is recommended that at least 48  
inches of straight duct be provided  
from the discharge of the units prior to  
any take-offs or transitions. This is a  
requirement for electric heat fan-  
powered units used in  
Trane offers a factory-mounted actuator  
with a 90-second drive time.The  
actuator drives 1 degree per second. A  
field-installed actuator may be used if  
desired.The actuator shaft has a ½-inch  
diameter and is designed to travel  
clockwise to close the damper and  
counter-clockwise to open the damper.  
There is an indicator on the end of the  
actuator shaft that can be used to  
determine the position of the damper.  
It is recommended that piping to the  
water coil should be done after field-  
mounted controls, external insulation,  
and ductwork connections have been  
completed.  
Do not connect water valve or pipe  
extensions to the water coil  
connections unless supported.  
applications with 100%  
downward discharge.  
Note: In order to maintain the UL rating  
forVariTrane electric coils, there must be  
four feet of straight unlined ductwork  
downstream of the reheat coil prior to  
any diffuser takeoffs.  
Unit Accessibility  
CAUTION  
Single-duct and dual-duct units  
Equipment Damage  
provided with hot water reheat have an  
access panel located on the side of the  
water coil. All other single-duct and  
dual-duct units are provided without  
access, as all functioning components  
are external to the unit.  
Note:When installing or replacing the  
actuator tighten the actuator set screw  
per the manufacturers instructions.  
Failure to follow the manufacturers  
specifications may result in unit  
malfunction.  
After all connections are made, check  
that the entire ductwork system is  
airtight. In some high-pressure  
Fan-powered terminals are provided  
with a sliding side access.  
systems, duct sealer may be necessary.  
Provide insulation around the entire  
inlet collar (all the way to the unit  
casing).  
Low-height terminal units have a  
removable bottom panel.  
Clearances  
Use caution not to damage the flow  
tubes when making ductwork  
connections or insulating.  
For proper service, it is recommended  
that at least 36” of side clearance be  
provided to service and access single-  
duct and dual-duct terminals units.  
Cut “slits” in the insulation for the flow  
tubes and secure with duct tape.  
Fan-poweredVAV units have a plenum  
inlet that must be clear of obstructions.  
Allow at least 36” of clearance in front  
of the side access and plenum opening.  
If the unit is to be installed in a location  
with high humidity, external insulation  
around the heating coil should be  
installed as required.  
Low-height fan-powered terminals  
require the same plenum clearance  
requirement that applies to the  
standard fan-powered units. However  
the access to the internal components  
is located on the bottom of the unit.  
Water Coil Connections  
Water coil piping connections will be  
3/8” or 7/8” OD.  
If necessary, you can change the coil  
connection from left-handed to right-  
handed (and vice-versa) by  
disconnecting the coil from the unit  
and rotating the coil “like a steering  
wheel” 180°.  
It is also recommended that 6” of  
clearance be provided to the top and  
bottom of all the units.  
Note:The minimum clearance for  
The inlet piping should always be  
connected to the bottom connection of  
the coil regardless of handedness.  
controls and heater controls should be  
36” for all models except units with 575-  
volt electric heaters, which require 48” of  
clearance. NEC and/or local codes  
override all clearance requirements.  
VAV-SVN01E-EN  
31  
Unit  
Setup  
Chart 2 – Flow Sensor Delta P vs.Airflow Delivery  
10  
8" x 12"  
12" 14" 16"  
6
10"  
8"  
16" x 24"  
4
5
1
0.1  
0.01  
10  
100  
1,000  
10,000  
Airflow (CFM)  
Chart 3– Fan MotorAmperage  
Maximum PSC Fan MotorAmperage (FLA)  
Maximum ECM Fan MotorAmperage (FLA)  
Fan  
HP  
VAC  
1/8  
115  
VAC  
1.6  
277  
VAV  
0.7  
1.6  
2.0  
2.4  
3.8  
4.7  
2.5  
2.5  
5.0  
3.5  
347  
VAC  
.7  
208  
Fan  
HP  
VAC  
1/3  
1/2  
1
115  
VAC  
4.5  
277  
VAV  
2.4  
3.5  
5.4  
5.1  
1.1  
Size  
Size  
Parallel/Series 02SQ  
Parallel/Series 03SQ  
Parallel/Series 04SQ  
Parallel/Series 05SQ  
Parallel/Series 06SQ  
Parallel/Series 07SQ  
Low-height Parallel/Series 08SQ  
Low-height Parallel/Series 09SQ  
Series Low-height 10SQ  
Parallel Low-Height 10SQ  
Parallel/Series 03SQ  
Parallel/Series 04SQ  
Parallel/Series 05SQ  
Parallel/Series 06SQ  
1/3  
1/3  
1/2  
1/2  
1
1/3  
1/3  
2 x 1/8  
2 x 1/8  
4.3  
5.5  
6.7  
1.4  
1.8  
2.2  
3.3  
3.8  
1.8  
1.8  
3.5  
3.0  
6.5  
10.1  
9.5  
1
4.6  
6.6  
Low-height Parallel/Series 08SQ 1/2  
2.0  
Low-height Parallel/Series 09SQ 1/2  
6.7  
3.6  
4.0  
5.5  
5.5  
11.0  
9.4  
Low-height Series 10SQ  
2 x 1/2  
7.5  
32  
VAV-SVN01E-EN  
Unit  
Setup  
(SCR) Motor Speed Control  
Adjustment Procedure.  
Figure 17 – Internal Potentiometer  
Electrically Commutated Motor (ECM)  
Trane offers an energy efficient ECM  
motor as a motor option. Balancing of  
an ECM motor is accomplished  
through electronic control adjustments  
on the ECM control board (see Figure  
15). Potentiometer settings for a  
multitude of CFM settings are given in  
Charts 4–15. Other potentiometer  
settings can be determined either by  
interpolating from these tables or by  
using the following equation:  
In order to make units more convenient  
and efficient to balance, an SCR  
(silicone control rectifier) is provided as  
standard on all fan-powered units.  
Max  
120 v  
The SCR is located on the side of the  
fan control box. To adjust the speed of  
the motor, the external knob must be  
rotated either clockwise or  
counterclockwise depending on the  
desired speed adjustment.  
208 v–  
277 v  
347 v  
CFMsetting = CFMmin +  
{(Potentiometer Setting) x [(CFMmax -  
CFMmin)/100]}  
There is an internal potentiometer  
(Figure 14) setting on the SCR controller  
that can be accessed by removing the  
control box cover. This internal  
potentiometer is set at the factory to the  
specific motor voltage.  
It may be necessary to adjust this in the  
field depending on the buildings power  
factor.  
DO NOT SET THIS  
POTENTIOMETER  
BELOW THE VOLTAGE  
OF THE FAN MOTOR.  
There is an LED on the ECM control  
board, which will blink one time for  
every 100 CFM of motor setting. For  
example, the LED on a unit set for 790  
CFM will blink 7 times. The LED on a  
unit set for 800 CFM will blink 8 times.  
NOTE: Do not set this potentiometer  
below the voltage of the fan motor.  
NOTE:This feature only verifies that the  
CFM is set properly. This feature does  
not indicate at what speed the motor is  
actually running.  
WARNING  
HazardousVoltage!  
Disconnect all electric power, including  
remote disconnects before servicing.  
Follow proper lockout/tagout proce-  
dures to ensure the power cannot be  
inadvertently energized. Failure to  
disconnect power before servicing  
could result in death or serious injury.  
The ECM must be “load tested.” In other  
words, the fan must be connected to  
properly test the ECM.  
Figure 18 – ECM Control Board  
Figure 16 – SCR  
VAV-SVN01E-EN  
33  
Unit  
Setup  
Chart 4 VPxF 03SQ ECM CFMTable  
VPxF 03SQ  
Motor Min CFM: 160  
Motor Max CFM: 1085  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
CFM  
L/sec  
CFM  
Switch  
160  
170  
179  
188  
198  
76  
80  
84  
89  
93  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
627  
637  
646  
655  
665  
296  
300  
305  
309  
314  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
207  
216  
226  
235  
244  
98  
102  
107  
111  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
674  
683  
693  
702  
711  
318  
323  
327  
331  
336  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
115  
254  
263  
272  
282  
291  
120  
124  
129  
133  
137  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
721  
730  
739  
749  
758  
340  
345  
349  
353  
358  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
300  
310  
319  
328  
338  
142  
146  
151  
155  
159  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
767  
777  
786  
795  
805  
362  
367  
371  
375  
380  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
347  
356  
366  
375  
385  
164  
168  
173  
177  
181  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
814  
823  
833  
842  
852  
384  
389  
393  
397  
402  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
394  
403  
413  
422  
431  
186  
190  
195  
199  
204  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
861  
870  
880  
889  
898  
406  
411  
415  
419  
424  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
441  
450  
459  
469  
478  
208  
212  
217  
221  
226  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
908  
917  
926  
936  
945  
428  
433  
437  
442  
446  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
487  
497  
506  
515  
525  
230  
234  
239  
243  
248  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
954  
964  
973  
982  
992  
450  
455  
459  
464  
468  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
534  
543  
553  
562  
571  
252  
256  
261  
265  
270  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1001  
1010  
1020  
1029  
1038  
472  
477  
481  
486  
490  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
581  
590  
599  
609  
618  
274  
278  
283  
287  
292  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
1048  
1057  
1066  
1076  
1085  
494  
499  
503  
508  
512  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
34  
VAV-SVN01E-EN  
Unit  
Setup  
Chart 5 VPxF 04SQ ECM CFMTable  
VPxF 04SQ  
Motor Min CFM: 220  
Motor Max CFM: 1510  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
L/sec  
CFM  
L/sec  
220  
233  
246  
259  
272  
104  
110  
116  
122  
128  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
872  
885  
898  
911  
924  
411  
417  
424  
430  
436  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
285  
298  
311  
324  
337  
135  
141  
147  
153  
159  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
937  
950  
963  
976  
989  
442  
448  
454  
461  
467  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
350  
363  
376  
389  
402  
165  
171  
178  
184  
190  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
1002  
1015  
1028  
1041  
1054  
473  
479  
485  
491  
497  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
415  
429  
442  
455  
468  
196  
202  
208  
215  
221  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
1067  
1080  
1093  
1106  
1119  
504  
510  
516  
522  
528  
66  
67  
68  
69  
7 0  
6
6
6
6
7
6
7
8
9
0
481  
494  
507  
520  
533  
227  
233  
239  
245  
251  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
1132  
1145  
1158  
1171  
1184  
534  
540  
547  
553  
559  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
546  
559  
572  
585  
598  
258  
264  
270  
276  
282  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
1197  
1210  
1223  
1236  
1249  
565  
571  
577  
584  
590  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
611  
624  
637  
650  
663  
288  
294  
301  
307  
313  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
1262  
1275  
1288  
1302  
1315  
596  
602  
608  
614  
620  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
676  
689  
702  
715  
728  
319  
325  
331  
338  
344  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
1328  
1341  
1354  
1367  
1380  
627  
633  
639  
645  
651  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
741  
754  
767  
780  
793  
350  
356  
362  
368  
374  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1393  
1406  
1419  
1432  
1445  
657  
663  
670  
676  
682  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
806  
819  
832  
845  
859  
381  
387  
393  
399  
405  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
1458  
1471  
1484  
1497  
1510  
688  
694  
700  
706  
713  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
VAV-SVN01E-EN  
35  
Unit  
Setup  
Chart 6 VPxF 05SQ ECM CFMTable  
VPxF 05SQ  
Motor Min CFM: 280  
Motor Max CFM: 1850  
%
L/sec  
TENS  
Switch  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
Setting  
CFM  
L/Sec  
280  
296  
312  
327  
343  
132  
140  
147  
155  
162  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
1073  
1089  
1105  
1120  
1136  
506  
514  
521  
529  
536  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
359  
375  
391  
407  
423  
170  
177  
184  
192  
199  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
1152  
1168  
1184  
1200  
1216  
544  
551  
559  
566  
574  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
438  
454  
470  
486  
502  
207  
214  
222  
229  
237  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
1231  
1247  
1263  
1279  
1295  
581  
589  
596  
604  
611  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
518  
534  
549  
565  
581  
244  
252  
259  
267  
274  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
1311  
1327  
1342  
1358  
1374  
619  
626  
634  
641  
649  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
597  
613  
629  
645  
661  
282  
289  
297  
304  
312  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
1390  
1406  
1422  
1438  
1454  
656  
664  
671  
678  
686  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
676  
692  
708  
724  
740  
319  
327  
334  
342  
349  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
1469  
1485  
1501  
1517  
1533  
693  
701  
708  
716  
723  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
756  
772  
787  
803  
819  
357  
364  
372  
379  
387  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
1549  
1565  
1580  
1596  
1612  
731  
738  
746  
753  
761  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
835  
851  
867  
883  
898  
394  
402  
409  
417  
424  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
1628  
1644  
1660  
1676  
1691  
768  
776  
783  
791  
798  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
914  
930  
946  
962  
978  
431  
439  
446  
454  
461  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1707  
1723  
1739  
1755  
1771  
806  
813  
821  
828  
836  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
994  
469  
476  
484  
491  
499  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
1787  
1802  
1818  
1834  
1850  
843  
851  
858  
866  
873  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
1009  
1025  
1041  
1057  
36  
VAV-SVN01E-EN  
Unit  
Setup  
Chart 7 VPxF 06SQ ECM CFMTable  
VPxF 06SQ  
Motor Min CFM: 530  
Motor Max CFM: 2100  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
`UNITS  
Switch  
CFM  
Switch  
CFM  
L/sec  
530  
546  
562  
577  
593  
250  
258  
265  
273  
280  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
1323  
1339  
1355  
1370  
1386  
624  
632  
639  
647  
654  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
609  
625  
641  
657  
673  
287  
295  
302  
310  
317  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
1402  
1418  
1434  
1450  
1466  
662  
669  
677  
684  
692  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
688  
704  
720  
736  
752  
325  
332  
340  
347  
355  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
1481  
1497  
1513  
1529  
1545  
699  
707  
714  
722  
729  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
768  
784  
799  
815  
831  
362  
370  
377  
385  
392  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
1561  
1577  
1592  
1608  
1624  
737  
744  
752  
759  
767  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
847  
863  
879  
895  
911  
400  
407  
415  
422  
430  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
1640  
1656  
1672  
1688  
1704  
774  
782  
789  
796  
804  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
926  
942  
958  
974  
990  
437  
445  
452  
460  
467  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
1719  
1735  
1751  
1767  
1783  
811  
819  
826  
834  
841  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
1006  
1022  
1037  
1053  
1069  
475  
482  
490  
497  
505  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
1799  
1815  
1830  
1846  
1862  
849  
856  
864  
871  
879  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
1085  
1101  
1117  
1133  
1148  
512  
520  
527  
535  
542  
36  
37  
3 8  
39  
40  
3
3
3
3
4
6
7
8
9
0
1878  
1894  
1910  
1926  
1941  
886  
894  
901  
909  
916  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
1164  
1180  
1196  
1212  
1228  
549  
557  
564  
572  
579  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1957  
1973  
1989  
2005  
2021  
924  
931  
939  
946  
954  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
1244  
1259  
1275  
1291  
1307  
587  
594  
602  
609  
617  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
2037  
2052  
2068  
2084  
2100  
961  
969  
976  
984  
991  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
VAV-SVN01E-EN  
37  
Unit  
Setup  
Chart 8 VSxF 03SQ ECM CFMTable  
VSxF 03SQ  
Motor Min CFM: 200  
Motor Max CFM: 1100  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
CFM  
L/sec  
CFN  
Switch  
200  
209  
218  
227  
236  
94  
99  
103  
107  
112  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
655  
664  
673  
682  
691  
309  
313  
318  
322  
326  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
246  
255  
264  
273  
282  
116  
120  
124  
129  
133  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
700  
709  
718  
727  
736  
330  
335  
339  
343  
348  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
291  
300  
309  
318  
327  
137  
142  
146  
150  
154  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
745  
755  
764  
773  
782  
352  
356  
360  
365  
369  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
336  
346  
355  
364  
373  
159  
163  
167  
172  
176  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
791  
800  
809  
818  
827  
373  
378  
382  
386  
390  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
382  
391  
400  
409  
418  
180  
185  
189  
193  
197  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
836  
845  
855  
864  
873  
395  
399  
403  
408  
412  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
427  
436  
446  
455  
464  
202  
206  
210  
215  
219  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
882  
891  
900  
909  
918  
416  
420  
425  
429  
433  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
473  
482  
491  
500  
509  
223  
227  
232  
236  
240  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
927  
936  
945  
955  
964  
438  
442  
446  
451  
455  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
518  
527  
536  
546  
555  
245  
249  
253  
257  
262  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
973  
982  
991  
1000  
1009  
459  
463  
468  
472  
476  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
564  
573  
582  
591  
600  
266  
270  
275  
279  
283  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1018  
1027  
1036  
1045  
1055  
481  
485  
489  
493  
498  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
609  
618  
627  
636  
646  
287  
292  
296  
300  
305  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
1064  
1073  
1082  
1091  
110 0  
502  
506  
511  
515  
519  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
38  
VAV-SVN01E-EN  
Unit  
Setup  
Chart 9VSxF 04SQ ECM CFMTable  
VSxF 04SQ  
Motor Min CFM: 275  
Motor Max CFM: 1500  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
Switch  
CFM  
L/sec  
275  
288  
300  
312  
325  
130  
136  
142  
147  
153  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
894  
906  
919  
931  
943  
422  
428  
434  
439  
445  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
337  
350  
362  
374  
387  
159  
165  
171  
177  
183  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
956  
968  
980  
993  
1005  
451  
457  
463  
469  
474  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
399  
411  
424  
436  
449  
188  
194  
200  
206  
212  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
1018  
1030  
1042  
1055  
1067  
480  
486  
492  
498  
504  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
461  
473  
486  
498  
510  
218  
223  
229  
235  
241  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
1079  
1092  
1104  
1117  
1129  
509  
515  
521  
527  
533  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
523  
535  
548  
560  
572  
247  
253  
258  
264  
270  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
1141  
1154  
1166  
1178  
1191  
539  
544  
550  
556  
562  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
585  
597  
609  
622  
634  
276  
282  
288  
293  
299  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
1203  
1215  
1228  
1240  
1253  
568  
574  
579  
585  
591  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
646  
659  
671  
684  
696  
305  
311  
317  
323  
328  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
1265  
1277  
1290  
1302  
1314  
597  
603  
609  
615  
620  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
708  
721  
733  
745  
758  
334  
340  
346  
352  
358  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
1327  
1339  
1352  
1364  
1376  
626  
632  
638  
644  
650  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
770  
783  
795  
807  
820  
363  
369  
375  
381  
387  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1389  
1401  
1413  
1426  
1438  
655  
661  
667  
673  
679  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
832  
844  
857  
869  
882  
393  
399  
404  
410  
416  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
1451  
1463  
1475  
1488  
1500  
685  
690  
696  
702  
708  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
VAV-SVN01E-EN  
39  
Unit  
Setup  
Chart 10VSxF 05SQ ECM CFMTable  
VSxF 05SQ  
Motor Min CFM: 350  
Motor Max CFM: 2050  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
L/sec  
CFM  
L/sec  
350  
367  
385  
402  
419  
165  
173  
181  
190  
198  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
1209  
1226  
1243  
1260  
1277  
570  
579  
587  
595  
603  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
436  
453  
470  
488  
505  
206  
214  
222  
230  
238  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
1295  
1312  
1329  
1346  
1363  
611  
619  
627  
635  
643  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
522  
539  
556  
573  
591  
246  
254  
263  
271  
279  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
1380  
1398  
1415  
1432  
1449  
651  
660  
668  
676  
684  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
608  
625  
642  
659  
676  
287  
295  
303  
311  
319  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
1466  
1483  
1501  
1518  
1535  
692  
700  
708  
716  
724  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
694  
711  
728  
745  
762  
327  
335  
344  
352  
360  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
1552  
1569  
1586  
1604  
1621  
732  
741  
749  
757  
765  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
779  
797  
814  
831  
848  
368  
376  
384  
392  
400  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
1638  
1655  
1672  
1689  
1707  
773  
781  
789  
797  
805  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
865  
882  
900  
917  
934  
408  
416  
425  
433  
441  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
1724  
1741  
1758  
1775  
1792  
814  
822  
830  
838  
846  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
951  
968  
985  
1003  
1020  
449  
457  
465  
473  
481  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
1810  
1827  
1844  
1861  
1878  
854  
862  
870  
878  
886  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
1037  
1054  
1071  
1088  
1106  
489  
498  
506  
514  
522  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1895  
1913  
1930  
1947  
1964  
895  
903  
911  
919  
927  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
1123  
1140  
1157  
1174  
1192  
530  
538  
546  
554  
562  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
1981  
1998  
2016  
2033  
2050  
935  
943  
951  
959  
967  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
40  
VAV-SVN01E-EN  
Unit  
Setup  
Chart 11VSxF 06SQ ECM CFMTable  
VSxF 06SQ  
Motor Min CFM: 700  
Motor Max CFM: 2500  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
CFM  
Switch  
CFM  
Switch  
700  
718  
737  
755  
773  
330  
339  
348  
356  
365  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
1609  
1627  
1646  
1664  
1682  
759  
768  
777  
785  
794  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
791  
809  
827  
846  
864  
373  
382  
391  
399  
408  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
1700  
1718  
1736  
1755  
1773  
802  
811  
820  
828  
837  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
882  
900  
918  
937  
955  
416  
425  
433  
442  
451  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
1791  
1809  
1827  
1846  
1864  
845  
854  
862  
871  
880  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
973  
991  
1009  
1027  
1046  
459  
468  
476  
485  
493  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
1882  
1900  
1918  
1936  
1955  
888  
897  
905  
914  
922  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
1064  
1082  
110 0  
1118  
1137  
502  
511  
519  
528  
536  
21  
22  
2 3  
2 4  
25  
2
2
2
2
2
1
2
3
4
5
1973  
1991  
2009  
2027  
2046  
931  
940  
948  
957  
965  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
1155  
1173  
1191  
1209  
1227  
545  
554  
562  
571  
579  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
2064  
2082  
2100  
2118  
2136  
974  
983  
991  
1000  
1008  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
1246  
1264  
1282  
1300  
1318  
588  
596  
605  
614  
622  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
2155  
2173  
2191  
2209  
2227  
1017  
1025  
1034  
1043  
1051  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
1336  
1355  
1373  
1391  
1409  
631  
639  
648  
656  
665  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
2245  
2264  
2282  
2300  
2318  
1060  
1068  
1077  
1085  
1094  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
1427  
1446  
1464  
1482  
1500  
674  
682  
691  
699  
708  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
2336  
2355  
2373  
2391  
2409  
1103  
1111  
1120  
1128  
1137  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
1518  
1536  
1555  
1573  
1591  
717  
725  
734  
742  
751  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
2427  
2445  
2464  
2482  
2500  
1146  
1154  
1163  
1171  
1180  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
VAV-SVN01E-EN  
41  
Unit  
Setup  
Chart 12– LPxF 08SQ ECM CFMTable  
LPxF 08SQ  
Motor Min CFM: 100  
Motor Max CFM: 460  
%
TENS  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
L/sec % Setting Switch  
CFM  
L/sec  
100  
103  
107  
111  
47  
49  
50  
52  
54  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
282  
285  
289  
293  
296  
133  
135  
136  
138  
140  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
114  
118  
121  
125  
129  
132  
56  
57  
59  
61  
62  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
300  
303  
307  
311  
314  
142  
143  
145  
147  
148  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
136  
140  
143  
147  
151  
64  
66  
68  
69  
71  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
318  
322  
325  
329  
333  
150  
152  
154  
155  
157  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
154  
158  
162  
165  
169  
73  
75  
76  
78  
80  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
336  
340  
344  
347  
351  
159  
160  
162  
164  
166  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
172  
176  
180  
183  
187  
81  
83  
85  
87  
88  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
354  
358  
362  
365  
369  
167  
169  
171  
172  
174  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
191  
194  
198  
202  
205  
90  
92  
93  
95  
97  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
373  
376  
380  
384  
387  
176  
178  
179  
181  
183  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
209  
212  
216  
220  
223  
99  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
391  
394  
398  
402  
405  
184  
186  
188  
190  
191  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
100  
102  
104  
105  
227  
231  
234  
238  
242  
107  
109  
111  
112  
114  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
409  
413  
416  
420  
424  
193  
195  
196  
198  
200  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
245  
249  
253  
256  
260  
116  
117  
119  
121  
123  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
427  
431  
435  
438  
442  
202  
203  
205  
207  
209  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
263  
267  
271  
274  
278  
124  
126  
128  
129  
131  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
445  
449  
453  
456  
460  
210  
212  
214  
215  
217  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
42  
VAV-SVN01E-EN  
Unit  
Setup  
Chart 13– LPxF 09SQ ECM CFMTable  
LPxF 09SQ  
Motor Min CFM: 250  
Motor Max CFM: 1025  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
Switch  
CFM  
L/sec  
250  
258  
265  
273  
281  
118  
122  
125  
129  
133  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
641  
649  
657  
665  
673  
303  
306  
310  
314  
317  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
289  
297  
305  
312  
320  
136  
140  
144  
147  
151  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
680  
688  
696  
704  
712  
321  
325  
329  
332  
336  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
328  
336  
344  
352  
359  
155  
159  
162  
166  
170  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
720  
727  
735  
743  
751  
340  
343  
347  
351  
354  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
367  
375  
383  
391  
399  
173  
177  
181  
184  
188  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
759  
767  
774  
782  
790  
358  
362  
365  
369  
373  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
406  
414  
422  
430  
438  
192  
196  
199  
203  
207  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
798  
806  
814  
821  
829  
377  
380  
384  
388  
391  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
446  
453  
461  
469  
477  
210  
214  
218  
221  
225  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
837  
845  
853  
861  
868  
395  
399  
402  
406  
410  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
485  
493  
500  
508  
516  
229  
232  
236  
240  
244  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
876  
884  
892  
900  
908  
414  
417  
421  
425  
428  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
524  
532  
540  
547  
555  
247  
251  
255  
258  
262  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
915  
923  
931  
939  
947  
432  
436  
439  
443  
447  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
563  
571  
579  
587  
594  
266  
269  
273  
277  
281  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
955  
962  
970  
978  
986  
450  
454  
458  
462  
465  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
602  
610  
618  
626  
634  
284  
288  
292  
295  
299  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
994  
1002  
1009  
1017  
1025  
469  
473  
476  
480  
484  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
VAV-SVN01E-EN  
43  
Unit  
Setup  
Chart 14– LSxF 08SQ ECM CFMTable  
LSxF 08SQ  
Motor Min CFM: 100  
Motor Max CFM: 460  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
%
TENS  
Switch  
UNITS  
Switch  
CFM  
L/sec  
CFM  
L/sec  
Settings  
100  
103  
107  
111  
47  
49  
50  
52  
54  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
282  
285  
289  
293  
296  
133  
135  
136  
138  
140  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
114  
118  
121  
125  
129  
132  
56  
57  
59  
61  
62  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
300  
303  
307  
311  
314  
142  
143  
145  
147  
148  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
136  
140  
143  
147  
151  
64  
66  
68  
69  
71  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
318  
322  
325  
329  
333  
150  
152  
154  
155  
157  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
154  
158  
162  
165  
169  
73  
75  
76  
78  
80  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
336  
340  
344  
347  
351  
159  
160  
162  
164  
166  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
172  
176  
180  
183  
187  
81  
83  
85  
87  
88  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
354  
358  
362  
365  
369  
167  
169  
171  
172  
174  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
191  
194  
198  
202  
205  
90  
92  
93  
95  
97  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
373  
376  
380  
384  
387  
176  
178  
179  
181  
183  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
209  
212  
216  
220  
223  
99  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
391  
394  
398  
402  
405  
184  
186  
188  
190  
191  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
100  
102  
104  
105  
227  
231  
234  
238  
242  
107  
109  
111  
112  
114  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
409  
413  
416  
420  
424  
193  
195  
196  
198  
200  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
245  
249  
253  
256  
260  
116  
117  
119  
121  
123  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
427  
431  
435  
438  
442  
202  
203  
205  
207  
209  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
263  
267  
271  
274  
278  
124  
126  
128  
129  
131  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
445  
449  
453  
456  
460  
210  
212  
214  
215  
217  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
44  
VAV-SVN01E-EN  
Unit  
Setup  
Chart 15– LSxF 09SQ ECM CFMTable  
LSxF 09SQ  
Motor Min CFM: 240  
Motor Max CFM: 950  
%
L/sec  
TENS  
Setting  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
Switch  
CFM  
L/sec  
240  
247  
255  
262  
269  
113  
117  
120  
123  
127  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
599  
606  
613  
620  
627  
283  
286  
289  
293  
296  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
276  
283  
290  
298  
305  
130  
134  
137  
140  
144  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
635  
642  
649  
656  
663  
299  
303  
306  
310  
313  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
312  
319  
326  
333  
341  
147  
151  
154  
157  
161  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
670  
678  
685  
692  
699  
316  
320  
323  
327  
330  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
348  
355  
362  
369  
376  
164  
167  
171  
174  
178  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
706  
713  
721  
728  
735  
333  
337  
340  
343  
347  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
384  
391  
398  
405  
412  
181  
184  
188  
191  
195  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
742  
749  
756  
764  
771  
350  
354  
357  
360  
364  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
419  
427  
434  
441  
448  
198  
201  
205  
208  
211  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
778  
785  
792  
799  
807  
367  
371  
374  
377  
381  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
455  
462  
470  
477  
484  
215  
218  
222  
225  
228  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
814  
821  
828  
835  
842  
384  
387  
391  
394  
398  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
491  
498  
505  
513  
520  
232  
235  
239  
242  
245  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
850  
857  
864  
871  
878  
401  
404  
408  
411  
415  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
527  
534  
541  
548  
556  
249  
252  
255  
259  
262  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
885  
893  
900  
907  
914  
418  
421  
425  
428  
431  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
563  
570  
577  
584  
592  
266  
269  
272  
276  
279  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
921  
928  
936  
943  
950  
435  
438  
442  
445  
448  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
VAV-SVN01E-EN  
45  
Unit  
Setup  
Chart 15– LSxF 10SQ ECM CFMTable  
LSxF 10SQ  
Motor Min CFM: 400  
Motor Max CFM: 1800  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
%
Setting  
TENS  
Switch  
UNITS  
Switch  
CFM  
L/sec  
CFM  
L/sec  
400  
414  
428  
443  
457  
189  
196  
202  
209  
216  
1
2
3
4
5
0
0
0
0
0
1
2
3
4
5
1107  
1121  
1135  
1150  
1164  
523  
529  
536  
543  
549  
51  
52  
53  
54  
55  
5
5
5
5
5
1
2
3
4
5
471  
485  
499  
513  
527  
222  
229  
236  
242  
249  
6
7
8
9
10  
0
0
0
0
1
6
7
8
9
0
1178  
1192  
1206  
1220  
1234  
556  
563  
569  
576  
583  
56  
57  
58  
59  
60  
5
5
5
5
6
6
7
8
9
0
542  
556  
570  
584  
598  
256  
262  
269  
276  
282  
11  
12  
13  
14  
15  
1
1
1
1
1
1
2
3
4
5
1249  
1263  
1277  
1291  
1305  
589  
596  
603  
609  
616  
61  
62  
63  
64  
65  
6
6
6
6
6
1
2
3
4
5
612  
626  
641  
655  
669  
289  
296  
302  
309  
316  
16  
17  
18  
19  
20  
1
1
1
1
2
6
7
8
9
0
1319  
1333  
1348  
1362  
1376  
623  
629  
636  
643  
649  
66  
67  
68  
69  
70  
6
6
6
6
7
6
7
8
9
0
683  
697  
711  
725  
740  
322  
329  
336  
342  
349  
21  
22  
23  
24  
25  
2
2
2
2
2
1
2
3
4
5
1390  
1404  
1418  
1432  
1447  
656  
663  
669  
676  
683  
71  
72  
73  
74  
75  
7
7
7
7
7
1
2
3
4
5
754  
768  
782  
796  
810  
356  
362  
369  
376  
382  
26  
27  
28  
29  
30  
2
2
2
2
3
6
7
8
9
0
1461  
1475  
1489  
1503  
1517  
689  
696  
703  
709  
716  
76  
77  
78  
79  
80  
7
7
7
7
8
6
7
8
9
0
824  
838  
853  
867  
881  
389  
396  
402  
409  
416  
31  
32  
33  
34  
35  
3
3
3
3
3
1
2
3
4
5
1531  
1545  
1560  
1574  
1588  
723  
729  
736  
743  
749  
81  
82  
83  
84  
85  
8
8
8
8
8
1
2
3
4
5
895  
909  
923  
937  
952  
422  
429  
436  
442  
449  
36  
37  
38  
39  
40  
3
3
3
3
4
6
7
8
9
0
1602  
1616  
1630  
1644  
1659  
756  
763  
769  
776  
783  
86  
87  
88  
89  
90  
8
8
8
8
9
6
7
8
9
0
966  
980  
994  
1008  
1022  
456  
462  
469  
476  
482  
41  
42  
43  
44  
45  
4
4
4
4
4
1
2
3
4
5
1673  
1687  
1701  
1715  
1729  
789  
796  
803  
809  
816  
91  
92  
93  
94  
95  
9
9
9
9
9
1
2
3
4
5
1036  
1051  
1065  
1079  
1093  
489  
496  
502  
509  
516  
46  
47  
48  
49  
50  
4
4
4
4
5
6
7
8
9
0
1743  
1758  
1772  
1786  
1800  
823  
829  
836  
843  
850  
96  
97  
98  
99  
100  
9
9
9
9
0
6
7
8
9
0
46  
VAV-SVN01E-EN  
Wiring  
Diagrams  
Figure 19 – Single-Duct Units (Electronic or DDC/UCM)  
Line Voltage  
L1 L2 N - 480  
(See Nameplate)  
L1 L2 - 208, 240  
L1 N - 277, 347  
SINGLE DUCT UNITS - ELECTRONIC OR DDC/UCM -  
HEATER TERMINALS - TYPICAL OF SINGLE PHASE VOLTAGES  
L1  
N
TB4  
SINGLE  
PHASE  
G
L1  
N
Manual Reset  
Cutout  
LINE  
Optional  
Fuse  
STAGES  
Contactor  
1st Stage  
VOLTAGES  
1
208  
240  
277  
347  
480  
2
3
Contactor  
2nd Stage  
Optional  
Fuse  
(208, 240, and 480)  
HEATER  
CONTACTORS  
Magnetic Contactors (MAGN)  
Mercury Contactors (MERC)  
Optional  
Transformer  
Contactor  
3rd Stage  
Air Flow  
Auto Reset  
Switch Thermal Cutout  
L1  
N
G
Optional  
Door  
Disconnect  
Switch  
24V Input from  
Controller  
24V Output to  
Controller  
SINGLE DUCT UNITS - ELECTRONIC OR DDC/UCM -  
HEATER TERMINALS - TYPICAL OF THREE PHASE VOLTAGES  
Line Voltage  
(See Nameplate)  
L1 L2 L3 - 208,480,600  
L1 L2 L3  
Contactor  
1st Stage  
G
TB4  
L1 L2 L3  
THREE  
PHASE  
STAGES  
LINE  
1
2
3
VOLTAGES  
208  
480  
575  
Contactor  
2nd Stage  
Manual Reset  
Cutout  
HEATER  
Optional  
Fuse  
CONTACTORS  
Magnetic Contactors (MAGN)  
Mercury Contactors (MERC)  
Contactor  
3rd Stage  
Notes:  
1.  
FACTORY INSTALLED  
FIELD INSTALLED  
OPTIONAL  
Optional  
Transformer  
Air Flow  
Thermal Cutout Switch  
Auto Reset  
2. Actual heater wiring diagrams are supplied  
with each unit (3-stage shown).  
L1 L2 L3  
G
3. Load carrying P.E. Switches or Contactors  
are supplied depending upon amp drawn.  
4. Air Flow Switch, Auto Reset Thermal Cutout  
and Manual Reset Cutout are provided as standard.  
Optional  
Door  
Disconnect  
Switch  
5. Heater Line Fuses, Transformers, and Door  
Interlocking Disconnect are optional.  
6. If transformer is not ordered, a separate 24-volt  
power supply is required for operation of unit controls.  
24V Input from  
Controller  
24V Output to  
Controller  
VAV-SVN01E-EN  
47  
Wiring  
Diagrams  
Figure 20 – Single-Duct Units (Pneumatic Controls)  
SINGLE DUCT UNITS - PNEUMATIC CONTROL -  
HEATER TERMINAL - TYPICAL OF SINGLE PHASE VOLTAGES  
L1 L2 - 208, 240  
L1 L2 N - 480  
L1 N - 277, 347  
Line Voltage  
(See Nameplate)  
L1  
N
G
SINGLE  
PHASE  
LINE  
TB4  
Manual Reset  
Cutout  
L1  
N
Optional  
Fuse  
VOLTAGES  
Contactors  
STAGES  
208  
240  
277  
347  
480  
1
2
3
PE Switch  
1st Stage  
HEATER  
CONTACTORS  
P.E. with Magnetic Contactors (PEMA)  
P.E. with Mercury Contactors (PEME)  
Auto Reset  
Thermal Cutout  
Air Flow  
Switch  
P.E. Switch  
2nd Stage  
N
L1  
P.E. Switch  
3rd Stage  
G
Optional  
Door  
Disconnect  
Switch  
L1 L2 L3 - 208, 600  
L1 L2 L3 N - 480  
Line Voltage  
(See Nameplate)  
SINGLE DUCT UNITS - PNEUMATIC CONTROL -  
HEATER TERMINAL - TYPICAL OF THREE PHASE VOLTAGES  
L1 L2 L3  
G
THREE  
Manual Reset  
Cutout  
Optional  
Fuse  
PHASE  
STAGES  
1
Contactors  
L1 L2 L3  
TB4  
LINE  
VOLTAGES  
208  
2
3
480  
575  
HEATER  
CONTACTORS  
P.E. with Magnetic Contactors (PEMA)  
P.E. with Mercury Contactors (PEME)  
PE Switch  
1st Stage  
Air Flow  
Switch  
Auto Reset  
Thermal Cutout  
NOTE:  
P.E. Switch  
2nd Stage  
FACTORY INSTALLED  
FIELD INSTALLED  
OPTIONAL  
L1 L2 L3  
N
N
1.  
2.  
G
Actual heater wiring diagram is supplied  
with each unit (3-stage shown).  
P.E. Switch  
3rd Stage  
3.  
4.  
Load carrying P.E. Switches or Contactors  
are supplied depending upon amp drawn.  
Optional  
Door  
Disconnect  
Switch  
Air Flow Switch, Auto Reset Thermal Cutout  
and Manual Reset Cutout provided as standard.  
Heater Line Fuses and Door Interlocking  
Disconnect are optional.  
5.  
48  
VAV-SVN01E-EN  
Wiring  
Diagrams  
Figure 21 – Fan-Powered Units (Electronic or DDC/UCM)  
Line Voltage  
(See Nameplate)  
L1 L2 N - 208, 240, 480  
L1 N - 277, 347  
FAN-POWERED UNITS - ELECTRONIC OR DDC/UCM -  
HEATER TERMINALS - TYPICAL OF SINGLE PHASE VOLTAGES  
L1 L2  
N
SINGLE  
PHASE  
TB4  
G
LINE  
L1 L2  
N
STAGES  
1
2
Optional  
Fuse  
Manual Reset  
Cutout  
VOLTAGES  
Contactor  
1st Stage  
208  
240  
277  
347  
480  
HEATER  
CONTACTORS  
Magnetic Contactors (MAGN)  
Mercury Contactors (MERC)  
Contactor  
2nd Stage  
Optional  
Air Flow  
Switch  
Auto Reset  
Thermal Cutout  
L1 L2  
N
G
Optional  
Door  
Disconnect  
Switch  
24V Input from  
Controller  
115 or 277V  
Output to Motor  
FAN-POWERED UNITS - ELECTRONIC OR DDC/UCM -  
HEATER TERMINALS - TYPICAL OF THREE PHASE VOLTAGES  
Line Voltage  
(See Nameplate)  
L1 L2 L3 N - 208,480,600  
L1 L2 L3  
N
Contactor  
1st Stage  
G
TB4  
THREE  
PHASE  
L1 L2 L3  
N
STAGES  
1
2
Optional  
Fuse  
Manual Reset  
Cutout  
LINE  
VOLTAGES  
208  
480  
575  
HEATER  
CONTACTORS  
Magnetic Contactors (MAGN)  
Mercury Contactors (MERC)  
Contactor  
2nd Stage  
Notes:  
1.  
Optional  
Air Flow  
FACTORY INSTALLED  
FIELD INSTALLED  
OPTIONAL  
Auto Reset  
Thermal Cutout Switch  
L1 L2 L3  
N
G
2. Actual heater wiring diagrams are supplied  
with each unit (2-stage shown).  
3. Load carrying P.E. Switches or Contactors  
are supplied depending upon amp drawn.  
4. Auto Reset Thermal Cutout and Manual Reset  
Cutout are provided as standard.  
Optional  
Door  
Disconnect  
Switch  
5. Heater Line Fuses, Airflow Switch, and Door  
Interlocking Disconnect are optional.  
24V Input from  
Controller  
115 or 277V  
Output to Motor  
VAV-SVN01E-EN  
49  
Wiring  
Diagrams  
Figure 22 – Fan-Powered Units (Pneumatic Controls)  
FAN-POWERED UNITS - PNEUMATIC CONTROL -  
HEATER TERMINAL - TYPICAL OF SINGLE PHASE VOLTAGES  
L1 L2 N - 208, 240, 480  
L1 N - 277, 347  
Line Voltage  
(See Nameplate)  
L1 L2  
N
G
SINGLE  
PHASE  
LINE  
TB4  
Manual Reset  
Cutout  
L1 L2  
N
Optional  
Fuse  
Contactors  
VOLTAGES  
STAGES  
PE Switch  
1st Stage  
208  
240  
277  
347  
480  
1
2
3
HEATER  
CONTACTORS  
Auto Reset  
Thermal Cutout  
Optional  
Air Flow  
Switch  
P.E. with Magnetic Contactors (PEMA)  
P.E. with Mercury Contactors (PEME)  
L1 L2  
N
G
Optional  
Door  
Disconnect  
Switch  
115 to 277V  
Output to Motor  
FAN-POWERED UNITS - PNEUMATIC CONTROL -  
HEATER TERMINAL - TYPICAL OF THREE PHASE VOLTAGES  
Line Voltage  
(See Nameplate)  
L1 L2 L3 N - 208, 480, 575  
L1 L2 L3  
N
G
THREE  
Manual Reset  
Cutout  
Optional  
Fuse  
PHASE  
STAGES  
1
Contactors  
L1 L2 L3 N  
LINE  
VOLTAGES  
208  
TB4  
2
3
480  
PE Switch  
1st Stage  
575  
HEATER  
CONTACTORS  
P.E. with Magnetic Contactors (PEMA)  
P.E. with Mercury Contactors (PEME)  
P.E. Switch  
2nd Stage  
NOTE:  
L1 L2 L3  
N
N
FACTORY INSTALLED  
G
1.  
FIELD INSTALLED  
OPTIONAL  
Optional  
Air Flow  
Switch  
Auto Reset  
Thermal Cutout  
2.  
Actual heater wiring diagram is supplied  
with each unit (1 and 2-stage shown).  
Optional  
Door  
Disconnect  
Switch  
3.  
4.  
Load carrying P.E. Switches or Contactors  
are supplied depending upon amp drawn.  
Auto Reset Thermal Cutout and Manual Reset  
Cutout provided as standard.  
Heater Line Fuses, Door Interlocking  
Disconnect, and Airflow Switch are optional.  
5.  
115 to 277V  
Output to Motor  
50  
VAV-SVN01E-EN  
Wiring  
Diagrams  
Figure 23 – Fan-Powered Control Boxes  
Fan-powered Control Box  
with Electronic or DDC Controls  
Fan-powered Control Box  
with Pneumatic Controls  
Duct Pressure Switch Option  
LINE VOLTAGE  
LINE VOLTAGE  
OR FROM HEATER TERMINAL  
OR FROM HEATER TERMINAL  
GREEN  
GROUND  
SCREW  
GREEN  
GROUND  
SCREW  
N
N
L1  
L1  
5.  
5.  
TRANSFORMER  
TRANSFORMER  
6.  
Y
DISCONNECT  
SWITCH  
DISCONNECT  
SWITCH  
}
BK  
BK  
W
W
NO  
BL  
BR  
R
BK  
BK  
TO VAV  
C
CONTROLLER  
2.  
2.  
NC  
BK  
BK  
W
W
BK  
BK  
DUCT PRESSURE  
SWITCH  
BK  
BK  
2
2
4
3
4
3
MOTOR  
RELAY  
MOTOR  
RELAY  
BK  
BK  
BR  
BR  
FUSE  
FUSE  
4.  
4.  
1
1
24V  
24V  
R
R
W
W
W
W
MOTOR  
SPEED  
CONTROL  
MOTOR  
SPEED  
CONTROL  
TERMINAL  
BLOCK  
TERMINAL  
BLOCK  
FAN CONTROL BOX  
FAN CONTROL BOX  
W
W
BK  
BK  
BR  
BR  
BR  
BR  
MOTOR  
FAN  
MOTOR  
FAN  
CAPACITOR  
CAPACITOR  
3.  
3.  
Fan-powered Control Box  
with Pneumatic Controls  
LINE VOLTAGE  
WARNING  
OR FROM HEATER TERMINAL  
HAZARDOUS VOLTAGE!  
DISCONNECT, LOCK OUT AND TAG  
ALL ELECTRIC POWER INCLUDING  
REMOTE DISCONNECTS BEFORE  
SERVICING.  
GREEN  
GROUND  
SCREW  
N
L1  
5.  
DUCT PRESSURE MAIN CONTROL  
6.  
DISCHARGE MOTOR START/RUN  
CAPACITORS BEFORE SERVICING.  
DISCONNECT  
SWITCH  
BK  
FAILURE TO DISCONNECT POWER  
BEFORE SERVICING CAN CAUSE  
SEVERE PERSONAL INJURY OR DEATH.  
W
NO  
NC  
NO  
BK  
2.  
C
C
BK  
NC  
P.E. SWITCH-2  
CAUTION  
BK  
W
USE COPPER CONDUCTORS ONLY!  
P.E. SWITCH-1  
UNIT TERMINALS ARE NOT DESIGNED  
TO ACCEPT OTHER TYPES OF  
CONDUCTORS.  
BK  
BK  
BK  
NO  
6.  
FAILURE TO DO SO MAY CAUSE  
DAMAGE TO THE EQUIPMENT.  
BK  
FUSE  
C
4.  
NC  
P.E. SWITCH  
W
W
NOTES:  
1.  
FACTORY INSTALLED  
BY OTHERS  
MOTOR  
SPEED  
CONTROL  
TERMINAL  
BLOCK  
OPTIONAL OR ALTERNATE CIRCUITRY  
2.  
DISCONNECT SWITCH, FUSE, & SCR ARE LOCATED  
EXTERNAL TO CONTROL BOX.  
3.  
4.  
5.  
CAPACITOR IS INSTALLED ON FAN HOUSING.  
FUSE IS OPTIONAL.  
FAN CONTROL BOX  
W
BK  
BR  
BR  
DETERMINED BY MOTOR VOLTAGE ON ORDER.  
VOLTAGE FOUND ON UNIT NAMEPLATE.  
MOTOR  
FAN  
CAPACITOR  
3.  
6.  
FOR SERIES FAN POWERED TERMINAL UNITS ONLY.  
VAV-SVN01E-EN  
51  
Wiring  
Diagrams  
Figure 24 – Fan-Powered Units with ECM  
Fan-powered Control Box w/ ECM with Electronic or DDC Controls  
(Depending on the size of the unit, the ECM board may or may not be located  
in the fan control box.)  
Fan-powered Control Box w/ ECM with Pneumatic Controls  
Duct Pressure Switch Option  
LINE VOLTAGE  
OR FROM HEATER TERMINAL  
LINE VOLTAGE  
FAN  
FAN  
MOTOR  
OR FROM HEATER TERMINAL  
MOTOR  
4.  
4.  
L1  
N
BK  
GR  
Y
GR  
GREEN  
GROUND  
SCREW  
GREEN  
GROUND  
SCREW  
NEUT.  
24V  
RED  
TERMINAL  
BLOCK  
RED  
TERMINAL  
BLOCK  
2.  
DISCONNECT  
SWITCH  
2
4
3
DISCONNECT  
SWITCH  
3.  
W
FUSE  
2.  
BL  
BK  
ECM  
BOARD  
3.  
W
1
FUSE  
24V  
Y
MOTOR  
RELAY  
5.  
POWER  
FACTOR  
CORRECTION  
CHOKE  
NO  
NC  
3.  
BL  
NEUT.  
24V  
BL  
RED  
RED  
C
Y
TO VAV  
CONTROLLER  
DUCT  
BL  
}
PRESSURE  
SWITCH  
Y
ECM  
BOARD  
BL  
BK  
TRANSFORMER  
TRANSFORMER  
POWER FACTOR  
CORRECTION CHOKE  
FAN CONTROL BOX  
FAN CONTROL BOX  
WARNING  
HAZARDOUS VOLTAGE!  
DISCONNECT, LOCK OUT AND TAG  
ALL ELECTRIC POWER INCLUDING  
REMOTE DISCONNECTS BEFORE  
SERVICING.  
DISCHARGE MOTOR START/RUN  
CAPACITORS BEFORE SERVICING.  
Fan-powered Control Box with Pneumatic Controls  
FAILURE TO DISCONNECT POWER  
BEFORE SERVICING CAN CAUSE  
SEVERE PERSONAL INJURY OR DEATH.  
LINE VOLTAGE  
FAN  
MOTOR  
4.  
OR FROM HEATER TERMINAL  
CAUTION  
GR  
USE COPPER CONDUCTORS ONLY!  
GREEN  
GROUND  
SCREW  
UNIT TERMINALS ARE NOT DESIGNED  
TO ACCEPT OTHER TYPES OF  
CONDUCTORS.  
TERMINAL  
BLOCK  
FAILURE TO DO SO MAY CAUSE  
DAMAGE TO THE EQUIPMENT.  
DISCONNECT  
SWITCH  
2.  
BK  
3.  
W
DUCT PRESSURE MAIN CONTROL  
5.  
FUSE  
BL  
POWER FACTOR  
NO  
NC  
NO  
BK  
CORRECTION CHOKE  
C
C
BK  
NEUT.  
24V  
RED  
Y
NC  
P.E. SWITCH-2  
RED  
BL  
BK  
P.E. SWITCH-1  
BK  
TRANSFORMER  
NOTES:  
NO  
ECM  
BOARD  
1.  
C
FACTORY INSTALLED  
BY OTHERS  
OPTIONAL OR ALTERNATE CIRCUITRY  
NC  
P.E. SWITCH  
2.  
DISCONNECT SWITCH, FUSE, & SCR ARE LOCATED  
EXTERNAL TO CONTROL BOX.  
FAN CONTROL BOX  
3.  
4.  
FUSE IS OPTIONAL.  
DETERMINED BY MOTOR VOLTAGE ON ORDER.  
VOLTAGE FOUND ON UNIT NAMEPLATE.  
5.  
FOR SERIES FAN POWERED TERMINAL UNITS ONLY.  
52  
VAV-SVN01E-EN  
Wiring  
Diagrams  
Figure 25 – Fan-Powered Low-Height Units  
Fan-Powered Low-Height Control Box with Electronic or DDC Controls  
CAPACITOR  
FAN  
3.  
MOTOR 2  
(SIZE 10 ONLY)  
FAN  
3.  
MOTOR  
Fan-Powered Low-Height Control Box with Pneumatic Controls  
Duct Pressure Switch Option  
5.  
BR  
CAPACITOR  
LINE VOLTAGE  
OR FROM HEATER TERMINAL  
BR  
CAPACITOR  
3.  
FAN  
MOTOR 2  
(SIZE 10 ONLY)  
BR  
FAN  
BR  
W
L1  
N
BK  
MOTOR  
W
BK  
3.  
5.  
OR FROM HEATER TERMINAL  
CAPACITOR  
LINE VOLTAGE  
GREEN  
GROUND  
SCREW  
BR  
BR  
W
BR  
2.  
2.  
L1  
N
W
BK  
BR  
MOTOR  
SPEED  
GREEN  
CONTROL  
BK  
GROUND  
SCREW  
DISCONNECT  
MOTOR  
SPEED  
BK  
W
SWITCH  
2.  
W
W
BK  
BK  
W
W
CONTROL  
TERMINAL  
BLOCK  
W
W
2.  
DISCONNECT  
SWITCH  
TERMINAL  
BLOCK  
W
4.  
BK  
BK  
W
BR  
W
FUSE  
BR  
W
W
4.  
FUSE  
BK  
W or BR  
Y
BK  
BK  
BK  
TO VAV  
CONTROLLER  
BL  
BK  
6.  
2
MOTOR  
RELAY  
BK  
2
4
4
BR  
R
}
NO  
NC  
TRANSFORMER  
24V  
BR  
BL  
BL  
Y
BL  
C
1
24V  
3
TRANSFORMER  
1
24V  
3
R
DUCT  
MOTOR  
RELAY  
PRESSURE  
SWITCH  
FAN CONTROL BOX  
FAN CONTROL BOX  
WARNING  
HAZARDOUS VOLTAGE!  
DISCONNECT, LOCK OUT AND TAG  
ALL ELECTRIC POWER INCLUDING  
REMOTE DISCONNECTS BEFORE  
SERVICING.  
DISCHARGE MOTOR START/RUN  
CAPACITORS BEFORE SERVICING.  
Fan-Powered Low-Height Control Box with Pneumatic Controls  
FAN  
MOTOR 2  
(SIZE 10 ONLY)  
FAILURE TO DISCONNECT POWER  
BEFORE SERVICING CAN CAUSE  
SEVERE PERSONAL INJURY OR DEATH.  
FAN  
MOTOR  
3.  
3.  
5.  
OR FROM HEATER TERMINAL  
BR  
CAUTION  
BR  
LINE VOLTAGE  
USE COPPER CONDUCTORS ONLY!  
BK  
UNIT TERMINALS ARE NOT DESIGNED  
TO ACCEPT OTHER TYPES OF  
CONDUCTORS.  
CAPACITOR  
W
BR  
L1  
N
BK  
W
CAPACITOR  
FAILURE TO DO SO MAY CAUSE  
DAMAGE TO THE EQUIPMENT.  
GREEN  
GROUND  
SCREW  
MOTOR  
SPEED  
CONTROL  
2.  
DUCT PRESSURE MAIN CONTROL  
6.  
W
W
BK  
BK  
W
TERMINAL  
BLOCK  
2.  
NO  
NC  
NO  
C
BK  
W
DISCONNECT  
SWITCH  
C
BK  
W
BR  
W
NC  
4.  
FUSE  
P.E. SWITCH-2  
P.E. SWITCH-1  
BK  
BK  
BK  
NOTES:  
1.  
NO  
FACTORY INSTALLED  
BY OTHERS  
OPTIONAL OR ALTERNATE CIRCUITRY  
BK  
C
NC  
2.  
3.  
DISCONNECT SWITCH, FUSE, & SCR ARE LOCATED  
EXTERNAL TO CONTROL BOX.  
P.E. SWITCH  
CAPACITOR IS INSTALLED ON FAN HOUSING.  
FUSE IS OPTIONAL.  
FAN CONTROL BOX  
4.  
5.  
DETERMINED BY MOTOR VOLTAGE ON ORDER.  
VOLTAGE FOUND ON UNIT NAMEPLATE.  
6.  
FOR SERIES FAN POWERED TERMINAL UNITS ONLY.  
VAV-SVN01E-EN  
53  
Wiring  
Diagrams  
Figure 26 – Fan-Powered Low-Height Units with ECM  
Fan-Powered Low-Height Control Box w/ ECM with Electronic or DDC Controls  
(Depending on the size of the unit, the ECM board may or may not be located  
in the fan control box.)  
Fan-Powered Low-Height Control Box w/ ECM with Pneumatic Controls  
Duct Pressure Switch Option  
4.  
LINE VOLTAGE  
LINE VOLTAGE  
4.  
OR FROM HEATER TERMINAL  
FAN  
MOTOR  
FAN  
MOTOR 2  
(SIZE 10 ONLY)  
OR FROM HEATER TERMINAL  
FAN  
MOTOR  
FAN  
MOTOR 2  
(SIZE 10 ONLY)  
BK  
GR  
GR  
GREEN  
GROUND  
SCREW  
GREEN  
GROUND  
SCREW  
W
Y
W
BK  
BK  
NEUT.  
24V  
RED  
TERMINAL  
BLOCK  
TERMINAL  
BLOCK  
RED  
2.  
DISCONNECT  
DISCONNECT  
SWITCH  
3.  
SWITCH  
W
2
2.  
4
3
FUSE  
BL  
BK  
3.  
W
Y
FUSE  
ECM  
BOARD  
5.  
1
24V  
NO  
BL  
NEUT.  
24V  
MOTOR  
RELAY  
BL  
RED  
RED  
C
NC  
DUCT  
PRESSURE  
SWITCH  
TO VAV  
CONTROLLER  
Y
Y
ECM  
BOARD  
BL  
BK  
}
BL  
BK  
TRANSFORMER  
TRANSFORMER  
FAN CONTROL BOX  
FAN CONTROL BOX  
WARNING  
HAZARDOUS VOLTAGE!  
DISCONNECT, LOCK OUT AND TAG  
ALL ELECTRIC POWER INCLUDING  
REMOTE DISCONNECTS BEFORE  
SERVICING.  
DISCHARGE MOTOR START/RUN  
CAPACITORS BEFORE SERVICING.  
FAILURE TO DISCONNECT POWER  
BEFORE SERVICING CAN CAUSE  
SEVERE PERSONAL INJURY OR DEATH.  
CAUTION  
USE COPPER CONDUCTORS ONLY!  
Fan-Powered Low-Height Control Box w/ ECM with Pneumatic Controls  
UNIT TERMINALS ARE NOT DESIGNED  
TO ACCEPT OTHER TYPES OF  
CONDUCTORS.  
4.  
LINE VOLTAGE  
FAILURE TO DO SO MAY CAUSE  
DAMAGE TO THE EQUIPMENT.  
FAN  
FAN  
MOTOR 2  
OR FROM HEATER TERMINAL  
MOTOR  
(SIZE 10 ONLY)  
GR  
GREEN  
GROUND  
SCREW  
W
BK  
DUCT PRESSURE MAIN CONTROL  
5.  
TERMINAL  
BLOCK  
DISCONNECT  
SWITCH  
2.  
BL  
BL  
3.  
NO  
BK  
NO  
NC  
W
Y
FUSE  
C
C
BK  
NC  
NEUT.  
RED  
24V  
RED  
Y
P.E. SWITCH-2  
P.E. SWITCH-1  
BK  
BL  
BK  
TRANSFORMER  
NOTES:  
1.  
FACTORY INSTALLED  
BY OTHERS  
OPTIONAL OR ALTERNATE CIRCUITRY  
ECM  
BOARD  
NO  
NC  
C
2.  
DISCONNECT SWITCH, FUSE, & SCR ARE LOCATED  
EXTERNAL TO CONTROL BOX.  
P.E. SWITCH  
3.  
4.  
FUSE IS OPTIONAL.  
FAN CONTROL BOX  
DETERMINED BY MOTOR VOLTAGE ON ORDER.  
VOLTAGE FOUND ON UNIT NAMEPLATE.  
5.  
FOR SERIES FAN POWERED TERMINAL UNITS ONLY.  
54  
VAV-SVN01E-EN  
Maintenance  
Figure 27 – Standard Motor Removal  
Figure 28 – Low-Height Motor Removal  
Periodic maintenance of theVariTrane  
product is minimal, but necessary for  
efficient operation. Routine mainte-  
nance consists of inspecting/replacing  
the air filters of the fan-powered  
terminals.  
Motors  
Both the PSC (permanent split capaci-  
tor) and the ECM (Electrically Commu-  
tated Motor) require no lubrication  
during its normal life of operation.  
FanWheel:  
Periodically, the fan wheel should be  
inspected for dirt or debris and cleaned  
as necessary.  
Standard height fan-powered series  
and parallel fan motors are replaceable  
through the filter opening and the  
standard sliding side access panel. To  
access the fan motor, the fan housing  
must be detached by removing the  
mounting bolts that hold the housing to  
the fan board. Removing the entire  
housing allows the fan motor, fan  
housing, and fan wheel to be re-aligned  
on a workbench or floor and prevent  
any possible fan wheel rubbing that  
may occur. Removing the housing will  
provide access to the motor shaft set  
screw that holds the fan wheel to the  
motor shaft.  
The low-height fan assembly was  
designed with an inlet ring that assists  
with removal of the fan motor. To  
access the fan motor assembly, the  
bottom panel must be removed. The  
inlet ring is held in place by six bolts  
and three motor mount bolts. Remove  
these bolts and the motor and fan  
wheel will come out of the fan housing.  
Filter  
The filter on fan-powered terminals will  
need to be inspected/replaced routinely  
depending on the environmental  
conditions of the plenum.  
Water Coil  
Water coils should be inspected and the  
fins should be cleaned periodically.  
Water coils have been provided with an  
access panel as standard to assist with  
inspection and cleaning.  
Fan Motor Replacement  
WARNING  
HazardousVoltage  
w/Capacitors!  
Disconnect all electric power, including  
remote disconnects and discharge all  
motor start/run capacitors before  
servicing. Follow proper lockout/tagout  
procedures to ensure the power cannot  
be inadvertently energized.Verify with  
an appropriate voltmeter that all  
capacitors have discharged. Failure to  
disconnect power and discharge  
capacitors before servicing could result  
in death or serious injury.  
WARNING  
Rotating Components!  
Disconnect all electric power, including  
remote disconnects before servicing.  
Follow proper lockout/tagout proce-  
dures to ensure the power cannot be  
inadvertently energized. Failure to  
disconnect power before servicing  
could result in death or serious injury.  
VAV-SVN01E-EN  
55  
Installation  
of Diffusers  
General  
Figure 29 – Diffuser Installation inT-Bar  
Ceiling  
Drywall/Plaster Ceiling  
All units must be installed upright and  
level as indicated by the arrow on the  
side of the units. Return air slots should  
be placed perpendicular and offset to  
the slot diffusers to avoid short-  
Finish installation of diffusers in plaster  
ceiling. Follow these procedures before  
completing the ceiling construction  
(Figure 31).  
1. Suspend the units above the intended  
ceiling level and their approximate  
horizontal positions and finish running  
flexible ductwork.  
circuiting of air distribution patterns.  
Place the unit in its approximate final  
position and check that it is upright and  
level. For single- slot units, engage  
the back of the diffuser over the t-bar  
with an edge and both ends resting on  
the t-bar. For double-slot units, slide  
the unit over the t-bar. For center-  
notch units, place diffuser over the  
t-bar, straddling it across a t-bar and  
resting on the units ends.  
2.After drywall and/or plaster is installed,  
cut openings to receive the diffuser air  
outlets. Also, allow for access openings  
to complete installation and service of  
the unit.  
3.Slide the trim accessory up and into the  
ceiling opening. Using the rim  
accessory as a template, drill four guide  
holes in the lip of the diffuser slot.  
Lower the unit onto the trim frame and  
attach with the sheet metal screws.  
Concealed Spline Ceiling  
Follow these procedures to finish  
installation of control and satellite  
diffusers and concealed spline for  
suspension ceilings before completing  
the ceiling construction (Figure 30).  
Place the units in their approximate  
final positions. If using the trim angle  
diffuser, its slots must be even with the  
spline level. If applying the trim  
If the unit has a fire damper, make sure  
that the damper is still fully open.  
Diffuser discharge must always be  
flush with the ceiling tiles to assure the  
proper airflow (Coanda effect).  
Note:The bottom of the throat section  
must be parallel to the ceilings for proper  
air distribution.  
Diffusers require specific installation  
information when mounting to a  
desired ceiling type. Select the ceiling  
type that closely matches the job site  
application and use the following  
procedures.  
CAUTION  
accessory, the bottom of the diffuser  
must be level with the finished ceiling.  
Equipment Damage!  
Do not install trim frame into ceiling  
using screws.When diffuser is placed  
on the trim frames, it will pull out.  
If installing the trim accessory, insert  
the trim into the ceiling opening from  
below and engage the diffuser slot to  
the trim t-bar structure.With bottom  
flange of trim accessory against the  
ceiling, and using the pre-drilled holes  
in the flange as a guide, drill holes in the  
flange of the diffuser. Join the diffuser  
and trim accessory with self-taping  
sheet metal.  
T-Bar Ceiling  
Finish installation of the diffuser in t-bar  
ceiling. (See Figure 29.) Follow these  
procedures before the ceiling construc-  
tion is completed.  
1.Position the diffuser at each end resting  
directly on the structural t-bar for  
support and the t-bar fitting into the  
channel provided at the unit discharge  
air throw.  
Figure 31 – Diffuser withTrim  
Accessory Installation in Plaster Ceiling  
Figure 30 – Diffuser withTrim  
Accessory Installation in Concealed  
Spline Ceiling  
2.A ceiling tile support flange is provided  
on each side of the discharge slot of the  
unit.Trim ceiling tile approximately 1½  
inches each to allow for width of  
discharge slot. For revealed edge  
ceilings, tile must be cut in a “Z”  
pattern.  
3.Install ceiling tiles in usual manner with  
cut edges resting on the flanges of the  
air slot.  
Plaster trim frame attaches with 2–4  
tension clips on the side of the diffuser.  
56  
VAV-SVN01E-EN  
Maintenance/  
Service Log  
Date  
Tag  
Serial #  
Service Notes  
VAV-SVN01E-EN  
57  
Maintenance/  
Service Log  
Date  
Tag  
Serial #  
Service Notes  
58  
VAV-SVN01E-EN  
Notes  
VAV-SVN01E-EN  
59  
Literature Order Number  
File Number  
VAV-SVN01E-EN  
SL-TD-000-VAV-SVN01E-EN-0606  
SL-TD-000-VAV-SVN01D-EN-0905  
Inland  
Supersedes  
Trane  
Stocking Location  
An American Standard Company  
Trane has a policy of continuous product and product data improvement and reserves the right to change  
design and specifications without notice. Only qualified technicians should perform the installation and  
servicing of equipment referred to in this publication.  
For more information contact  
your local district office or  
e-mail us at [email protected]  

Mitsubishi Electronics Pe 20myc User Manual
Ohlins 07235 01a5lP65 User Manual
Panasonic Cs E28ekr User Manual
Radio Shack Battery Charger User Manual
Radio Shack Tad 799 User Manual
Source Technologies Ac060x1223a B User Manual
Trion Air Purification Systems User Manual
Whirlpool 1157672 User Manual
Xerox Workcentre 5638 User Manual
York 13 Series User Manual