OWNER’S MANUAL
MODE D’EMPLOI
BEDIENUNGSANLEITUNG
MANUALE DI ISTRUZIONI
MANUAL DEL PROPIETARIO
ȅǻǾīǿǼȈ ȋȇǾȈǼȍȈ
MANUAL DO UTILIZADOR
AIR CONDITIONER
(SPLIT TYPE)
For general public use
Pour utilisation grand public
Für allgemeine Verwendung
Per l’uso in generale
Para el uso público general
īȚĮ ȖİȞȚțȒ įȘµȩıȚĮ ȤȡȒıȘ
Para utilização geral
CLIMATISEUR (TYPE SEPARE)
KLIMAGERÄT (GETEILTE AUSFÜHRUNG)
CONDIZIONATORE D’ARIA (TIPO SPLIT)
ACONDICIONADOR DE AIRE (TIPO SEPARADO)
ȀȁǿȂǹȉǿȈȉǿȀȅ (ǻǿǹǿȇȅȊȂǼȃȅȊ ȉȊȆȅȊ)
SISTEMA DE AR CONDICIONADO (TIPO SPLIT)
Indoor Unit
Outdoor Unit
Unité intérieure
Innenraumgerät
Unità interna
Unité extérieure
Außengerät
Unità esterna
Unidad interior
ǼıȦIJİȡȚțȒ µȠȞȐįĮ
Unidade interior
Unidad exterior
ǼȟȦIJİȡȚțȒ µȠȞȐįĮ
Unidade exterior
RAS-10JKVP-E / RAS-10JAVP-E
RAS-13JKVP-E / RAS-13JAVP-E
nchasing this TOSHIBA Air Conditioner. Please read this owner’s manual carefully before using your Air Conr.
Thank you for purchasing this TOSHIBA Air Conditioner. Please read this owner’s manual
carefully before using your Air Conditioner.
Avant tout, merci d’avoir porté votre choix sur un climatiseur TOSHIBA. Veuillez lire
attentivement ce mode d’emploi avant de mettre en service le climatiseur.
Wir danken Ihnen für den Kauf dieses TOSHIBA-Klimageräts. Lesen Sie die
Bedienungsanleitung sorgfältig durch, bevor Sie das Gerät in Betrieb nehmen.
Grazie per aver acquistato questo Condizionatore d’Aria TOSHIBA. Prima di usare il
Condizionatore d’Aria, si consiglia di leggere con attenzione il presente manuale.
Gracias por adquirir este acondicionador de aire TOSHIBA. Lea este manual del propietario
detenidamente antes de utilizar su acondicionador de aire.
ǼȣȤĮȡȚıIJȠȪµİ ȖȚĮ IJȘȞ ĮȖȠȡȐ ĮȣIJȠȪ IJȠȣ țȜȚµĮIJȚıIJȚțȠȪ IJȘȢ ȉȅȈǿȂȆǹ. ȆĮȡĮțĮȜİȓıșİ ȞĮ
įȚĮȕȐıİIJİ ʌȡȠıİțIJȚțȐ IJȚȢ ȠįȘȖȓİȢ ȤȡȒıİȦȢ ʌȡȚȞ ȤȡȘıȚµȠʌȠȚȒıİIJİ IJȠ ȀȜȚµĮIJȚıIJȚțȩ ıĮȢ.
Obrigado por ter adquirido este sistema de ar condicionado da TOSHIBA. Leia atentamente
este manual do utilizador antes de utilizar o sistema de ar condicionado.
CAUTION
.
INSTALLATION CAUTIONS
• Securely lay the drain hose for the best draining results.
• Incorrect drainage can cause flooding in the house and furniture to get wet.
• Be sure to connect the air conditioner to a dedicated power supply having the rated voltage.
Otherwise, the unit can break down or cause a fire.
• Do not install the unit in a place where inflammable gas can leak.
• A fire can result if inflammable gas accumulates around the unit.
• The indoor unit shall be installed so that the top of the indoor unit is at least 2 m in height. Also, avoid
putting anything on the top of the indoor unit.
OPERATION CAUTIONS
• Carefully read this manual before starting the air conditioner. The manual includes a lot of important
information for daily operation.
• Do not use this air conditioner for other purposes such as preserving food, precision instruments, art
objects, breeding animals, or growing potted plants.
• Do not install this air conditioner in a special-purpose room such as a ship or any kind of vehicle.
Doing so could harm machine performance.
• Avoid exposing potted plants and animals to wind from the air conditioner because it harms their
health and growth.
• When the air conditioner is operated together with a combustion device in the same place, pay
careful attention to ventilation and let fresh air into the room.
Poor ventilation can cause an oxygen shortage.
• When the air conditioner is used in a closed room, pay careful attention to the ventilation of the room.
Poor ventilation can cause an oxygen shortage.
• Do not touch the operation buttons with wet hands. Doing so could cause an electric shock.
• Do not place any combustion device in a place where it is directly exposed to wind from the air
conditioner. Doing so could cause incomplete combustion.
• When the air conditioner will not be used for an extended period of time, turn off the main switch or
the circuit breaker for added safety. Disconnecting from the power supply protects the unit from
lightning and power surges.
• Do not put a container with water such as a vase on the unit because water can enter into the unit
and cause an electric shock due to deterioration in the electric insulation.
• Check the concrete blocks underneath the outdoor unit occasionally. If the base is left damaged or
deteriorated, the unit can topple over and could possibly cause an injury.
• Do not wash the unit with water. This could cause an electric shock.
• Do not use alcohol, benzene, thinner, glass cleaner, polishing powder or other solvent for cleaning
the unit because they can deteriorate and damage the air conditioner.
• Before cleaning the unit, be sure to turn off the main switch or circuit breaker to prevent injuries from
the electric fan running inside.
• For details of the cleaning method, refer to “USUAL MAINTENANCE” and “SPECIAL
MAINTENANCE” on pages 18 to 22.
• Do not put anything on or step on the indoor unit and outdoor unit. If you do so, it can topple over and
cause an injury.
• To allow the air conditioner to operate at maximum performance, operate within the operating
temperature range specified in the instructions. Failure to do so can cause a malfunction, break
down, or water to leak from the unit.
EN
2
NAMES OF PARTS
Outdoor unit
b
a
a Drain hose, refrigerant connecting pipe and electric wires
b Air inlet (Side and rear)
c Air outlet
c
Indoor unit
d Room temperature sensor
e Front panel
f Air inlet grille
g Air filter
g
e
f
n
h Air outlet
i Horizontal air flow louver
j Vertical air flow louver
k Display panel
m
l Infrared signal receiver
m Remote control
n Dust collecting unit
o Air ionizer
i
k l j
o d
h
NAMES AND FUNCTIONS OF INDICATORS AND CONTROLS
ON INDOOR UNIT
Display panel
The operating states are shown below.
a PLASMA indicator (Blue)
PLASMA
FILTER
TIMER
RESET
OPERATION
b FILTER indicator (Orange)
c TIMER indicator (Yellow)
d
c
a
e
b
d RESET button
e OPERATION indicator (Green/*Orange)
The operation indicators flash rapidly (five times per second)
when a safety protection feature is activated.
* The OPERATION indicator is orange when the auto restart
function is activated.
RESET button
If you misplace or lose the remote control or its batteries are used
up, push the RESET button.
1. Push the RESET button to start the air conditioner. Push this
button again to stop operation.
3
EN
REMOTE CONTROL AND ITS FUNCTIONS
a Infrared signal transmitter
n Automatic operation button (AUTO)
Transmits signals to the indoor unit.
Press this button to operate the air conditioner
automatically.
(A receiving beep is heard.) () see page 16.)
o Economy button (ECO)
Press this button to operate the air conditioner
economically. () see page 16.)
p FILTER button
b
button
Press the button to start operation. (A receiving beep is
heard.) Press the button again to stop operation. (A
receiving beep is heard.)
If no receiving sound is heard from the indoor unit, press
the button twice.
Press this button to turn off the filter cleaning indicator on
the indoor unit.
Press this button after cleaning the air filter. () see
page 19.)
c Mode select button (MODE)
Press this button to select a mode. Each time you press
the button, the modes cycle in order from A: Auto
changeover control,
to A.
(A receiving beep is heard.)
: Cool,
: Dry,
: Heat and back
q PRESET button
Press this button to operate the air conditioner according to
the settings stored using the MEMO button. () see
page 13.)
TEMP
d Temperature button (
)
r Air purifying button (PAP)
Press this button to start the electrical air purifying
operation.
Press the button again to stop operation.
s Sleep timer button (SLEEP)
Press this button to start the sleep timer (OFF timer)
operation.
.. The temperature setting is increased to 30°C.
... The temperature setting is reduced to 17°C.
(A receiving beep is heard.)
e Fan speed button (FAN)
Press this button to select the fan speed. When you select
AUTO, the fan speed is automatically adjusted according to
the room temperature. You can also manually select the
desired fan speed from five available settings.
You can select the OFF timer time from among four
settings (1, 3, 5 or 9 hours).
(LOW , LOW+
, MED
, MED+
,
HIGH
) (A receiving beep is heard.)
f Auto louver button (SWING)
a
Press this button to swing the louver. (A receiving beep is
heard.)
Press the button again to stop the louver from swinging. (A
receiving beep is heard.) () see page 14.)
g Set louver button (FIX)
Press this button to adjust the air flow direction. (A
receiving beep is heard.) () see page 14.)
h ON timer button (ON)
Use this button to change the clock and ON timer times.
ON
To move up the time, press
of the “ON
” button.
r
d
n
q
AUTO
PAP
TEMP
ON
To move down the time, press
of the “ON
” button.
MODE
PRESET
c
b
l
g
f
i OFF timer button (OFF)
o
m
e
s
j
p
i
Use this button to change the OFF timer times.
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
OFF
To move up the time, press
of the “OFF
” button.
SWING
CLR
FIX
FAN
SLEEP
SET
k
ON
OFF
OFF
FILTER
To move down the time, press
of the “OFF
” button.
CLOCK
RESET
CHECK
j Reserve button (SET)
h
Press this button to store the time settings. (A receiving
beep is heard.)
k Cancel button (CLR)
Press this button to cancel the ON timer and OFF timer. (A
receiving beep is heard.)
l High power button (Hi POWER)
Press this button to start high power operation. () see
page 16.)
m Memory button (MEMO)
Press this button to ready for storing the settings.
Hold down the button for more than 3 seconds to store the
setting indicated on the remote control and until the
mark is displayed. () see page 13.)
EN
4
NAMES AND FUNCTIONS OF INDICATORS ON REMOTE
CONTROL
Display
All indicators, except for the clock time indicator, are displayed by pressing the
button.
a Transmission mark
This transmission mark ( ) indicates when the remote control transmits signals to the indoor unit.
b Mode indicator
h
adb j
c
Indicates the current operation mode.
(AUTO: Automatic control, A: Auto changeover control,
: Heat)
: Cool, : Dry,
c Temperature indicator
Indicates the temperature setting (17°C to 30°C).
d Air purifying indicator
Shows that the electrical air purifying operation is in progress.
e FAN speed indicator
Indicates the selected fan speed. AUTO or one of five fan speed levels (LOW
,
LOW+
, MED
, MED+
, HIGH
) can be shown.
: Dry.
e
i g
f
Indicates AUTO when the operating mode is either AUTO or
f TIMER and clock time indicator
• In the illustration, all indicators are shown
for purposes of explanation. During
operation, only the relevant indicators are
shown on the remote control.
The time setting for timer operation or the clock time is indicated.
The current time is always indicated except during TIMER operation.
g Hi POWER indicator
Indicates when Hi POWER operation starts.
Press the Hi POWER button to start and press it again to stop operation.
h
(MEMORY) indicator
Flashes for 3 seconds when the MEMO button is pressed during operation.
The
mark is shown when holding down the button for more than 3 seconds
while the mark is flashing.
Press another button to turn off the mark.
i ECO indicator
Indicates when the ECO is activated.
Press the ECO button to start and press it again to stop operation.
j A. B change indicator remote control
Press the CHECK point and FIX button at the same time to change the remote
control setting from “A” to “B”. (Priority is given to the “A” setting.)
The E-Parts of the indoor unit are also changed to the “B” setting.
PREPARATION AND CHECK BEFORE USE
• Slide off the cover while pressing the sides.
Loading the remote control batteries
a Remove the cover, and insert the batteries.
b Press the RESET button.
The clock indicator flashes.
• Battery replacement
Be careful not to reverse the (+) position and the (–)
position.
Adjust the clock.
Reattach the cover.
Batteries
• To replace the batteries, use two new batteries (AAA type).
• The batteries will last about one year under normal usage.
• Replace the batteries if there is no receiving beep from the
indoor unit or when the air conditioner cannot be operated using
the remote control.
• To avoid malfunctions due to battery leakage, remove the
batteries when not using the remote control for more than one
month.
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SWING
CLR
FIX
FAN
SLEEP
SET
ON
OFF
FILTER
CLOCK
RESET
b
CHECK
5
EN
Setting the clock
Before you start operating the air conditioner, set the clock of the remote control using the
procedures given in this section. The clock panel on the remote control will indicate the
time regardless of whether the air conditioner is in use or not.
Initial setting
When batteries are inserted in the remote control, the clock panel displays AM 0:00 and
flashes.
AUTO
PAP
TEMP
ON
a ON
button
PRESET
MODE
ON
Press the ON
button to set the current time.
Each press of the ON button changes the time in one minute increments.
Holding down the ON button changes the time in ten minute increments.
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SWING
CLR
FIX
FAN
OFF
SLEEP
SET
b
a
b SET
button
SET
ON
FILTER
SET
Press the SET
button.
CLOCK
RESET
The current time is displayed and the clock starts.
CHECK
Adjusting the clock
a CLOCK button
Press the CLOCK button.
The CLOCK indicator flashes.
ON
b ON
button
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SLEEP
SWING
CLR
FIX
FAN
ON
Press the ON
time.
Each press of the ON button changes the
time in one minute increments.
button to set the current
AUTO
PAP
SET
TEMP
ON
OFF
FILTER
CLOCK
RESET
MODE
PRESET
CHECK
Push CLOCK
Holding down the ON button changes the
time in ten minute increments.
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SET
c SET
button
SWING
CLR
FIX
FAN
OFF
SLEEP
b
a
SET
Press the SET
The current time is displayed and the clock
starts.
button.
SET
c
ON
FILTER
CLOCK
RESET
CHECK
Preparing the filters
a Open the air inlet grille, and remove the air filters.
b Attach the supplied Zeolite-plus filter and
Zeolite-3G filter.
Zeolite-3G filter
Zeolite-plus filter
EN
6
USING THE REMOTE CONTROL
CAUTION
• The air conditioner will not operate if curtains, doors or other objects block the signals from the remote control to the indoor
unit.
• Be careful that liquids do not spill onto the remote control.
Do not expose the remote control to direct sunlight or heat.
• If the infrared signal receiver on the indoor unit is exposed to direct sunlight, the air conditioner may not function properly.
Use curtains to prevent sunlight from reaching the receiver.
• Signals may not be properly received, if the room using the air conditioner has fluorescent lighting with electronic starters. If
you are planning on using fluorescent lamps, consult with your local dealer.
• If other electrical appliances are activated by the remote control, move these appliances or consult with your local dealer.
Location of the remote control
• Keep the remote control where its signals can reach the receiver of the indoor unit
(a distance of up to 7 m is allowed).
• When you select timer operation, the remote control automatically transmits a
signal to the indoor unit at the specified time.
If you keep the remote control in a location where proper signal transmission is
blocked, a time lag of up to 15 minutes may occur.
7 m
Remote control holder
Installing the remote control holder
• Before you actually install the remote control holder on a wall or pillar, check
whether the remote control signals can be received by the indoor unit.
Mounting and removing the remote control
• To mount the remote control, hold it parallel to the remote control holder and push
it in fully. To remove the remote control, slide the remote control upwards and out
from the holder.
7
EN
AUTOMATIC OPERATION
When you set the air conditioner to AUTO mode, it automatically selects cooling, heating, or fan only operation depending on the room
temperature. () see page 16.)
The fan speed and louver are also automatically controlled.
Start
a
button
Press this button to start the air conditioner.
b AUTO button (AUTO)
Press AUTO button.
• The OPERATION indicator (green or orange) on the display panel of the indoor unit
lights. The operating mode is selected according to the room temperature and
operation starts after approximately 3 minutes.
• If the AUTO mode is uncomfortable, you can select the desired conditions manually.
The temperature, fan speed and louver position can be changed, and MODE is also
changed from AUTO to A when the fan speed or louver position is changed.
The fan speed indicator is also shown.
b
a
PAP
AUTO
TEMP
MODE
PRESET
Stop
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
button
SWING
CLR
FIX
FAN
SLEEP
Press this button again to stop the air conditioner.
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
AUTOMATIC OPERATION (AUTO CHANGEOVER)
When you set the air conditioner to A mode or switch over from AUTO operation because of a change in settings, the air conditioner
automatically selects cooling, heating, or fan only operation depending on the room temperature. () see page 16.)
Start
a
button
Press this button to start the air conditioner.
b Mode select button (MODE)
Select A.
TEMP
c Temperature button (
)
Set the desired temperature.
• The OPERATION indicator (green or orange) on the display panel of the indoor unit
lights. The operating mode is selected according to the room temperature and operation
starts after approximately 3 minutes.
• The temperature, fan speed and louver position can be changed. You can select the
desired conditions manually.
AUTO
PAP
TEMP
c
b
a
PRESET
MODE
Stop
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SWING
CLR
FIX
FAN
SLEEP
button
Press this button again to stop the air conditioner.
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
EN
8
COOLING/HEATING OPERATION
Start
a
button
Press this button to start the air conditioner.
b Mode select button (MODE)
Select Cool
or Heat
.
TEMP
c Temperature button (
)
Set the desired temperature.
d Fan speed button (FAN)
Select one of “AUTO” LOW , LOW+
, MED
, MED+
,
AUTO
PAP
HIGH
.
TEMP
c
b
a
MODE
PRESET
• The OPERATION indicator (green or orange) on the display panel of the indoor unit
turns on. Operation starts after approximately 3 minutes.
Stop
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
d
SWING
CLR
FIX
FAN
SLEEP
button
Press this button again to stop the air conditioner.
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
DRY OPERATION
Start
a
button
Press this button to start the air conditioner.
b Mode select button (MODE)
Select DRY
.
TEMP
c Temperature button (
)
Set the desired temperature.
• The fan speed seting is fixed to AUTO and the AUTO is displayed.
• The OPERATION indicator (green or orange) on the display panel of the indoor unit
turns on, and operation starts after approximately 3 minutes.
AUTO
PAP
TEMP
c
b
a
MODE
PRESET
Stop
button
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
Press this button again to stop the air conditioner.
SWING
CLR
FIX
FAN
SLEEP
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
9
EN
AIR PURIFYING OPERATION
During air conditioner operation
a PAP button
Pressing this button starts Plasma Air Purifying (PAP) operation.
• The PLASMA indicator (blue) on the display panel of the indoor unit turns on.
• Plasma pure filter and air ionizer are activated.
To stop only PAP operation
PAP button
Pressing this button stops PAP operation.
• The PLASMA indicator (blue) on the display panel of the indoor unit turns off.
• Plasma pure filter and air ionizer are deactivated.
PAP
AUTO
a
TEMP
MODE
PRESET
To stop air conditioner operation at the same time
button
Pressing this button stops air conditioner operation and PAP operation.
• The OPERATION indicator (green or orange) and PLASMA indicator (blue) on the
display panel of the indoor unit turn off.
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SWING
CLR
FIX
FAN
SLEEP
SET
ON
OFF
FILTER
CLOCK
RESET
CAUTION
CHECK
• When the
button is pressed the next time, operation starts with the combined
air conditioner and PAP operation.
• During the combined air conditioner and PAP operation, air conditioner operation
only cannot be stopped.
When the air conditioner is stopped
a PAP button
Pressing this button starts PAP operation.
• The PLASMA indicator (blue) on the display panel of the indoor unit turns on.
INFORMATION
• The air ionizer starts in conjunction with air purifying operation.
• During the air purifying operation, a small amount of ozone is produced, and you might
notice the smell.
• When the air flow is automatic, it changes between LOW
and MED+
.
LOW operation is performed when the indoor air becomes clean. During operation,
the position of the vertical air flow louvers may change if the room temperature is low.
• Opening the front panel during PAP operation sometimes turns on the FILTER indicator
(orange).
In this case, stop PAP operation (stop the air conditioner if it is also operating), and then
close the front panel.
• The FILTER indicator (orange) turns on after PAP operation is performed for about 1000
hours.
PAP
AUTO
a
TEMP
MODE
PRESET
When the indicator turns on, clean the dust collecting unit. () see page 21.)
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SWING
CLR
FIX
FAN
SLEEP
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
EN
10
Hi POWER OPERATION
High power (Hi POWER)
• The Hi POWER (high power operation) mode automatically controls room temperature,
air flow and the operation mode so that the room is quickly cooled in summer and
warmed in winter. () see page 16.)
Setting Hi POWER mode
a Hi POWER button
Press the Hi POWER button. The Hi POWER mark on the remote control is shown.
Canceling Hi POWER mode
a Hi POWER button
AUTO
PAP
TEMP
Press the Hi POWER button once again.
The Hi POWER mark on the remote control turns off.
PRESET
MODE
CAUTION
HiPOWER
ECO
MEMO
a
.
.
.
The Hi POWER mode cannot be activated during DRY operation and when the ON
TIMER operation is activated.
1 3 5 9H
SWING
CLR
FIX
FAN
SLEEP
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
TIMER OPERATION
ON timer and OFF timer
Setting the ON Timer
ON
a ON
button
ON
Press the ON
button. Set the timer to the desired time.
Each time the ON button is pressed, the time changes in ten minute increments.
Holding down the ON button changes the time in one hour increments.
AUTO
PAP
SET
b SET
button
TEMP
SET
Press the SET
button to set the timer.
MODE
PRESET
The timer time is displayed, and the timer starts.
CLR
c CLR
button
CLR
Press the CLR
button to cancel the timer setting.
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
Setting OFF Timer
SWING
CLR
FIX
FAN
SLEEP
b
c
a
SET
OFF
a OFF
button
ON
OFF
FILTER
CLOCK
RESET
CHECK
OFF
Press the OFF
button.
Set the timer to the desired time.
Each time the OFF button is pressed, the time changes in ten minute increments.
Holding down the OFF button changes the time in one hour increments.
SET
b SET
button
SET
Press the SET
button to set the timer.
The timer time is displayed, and the timer starts.
CLR
c CLR
button
CLR
Press the CLR
button to cancel the timer setting
.
CAUTION
• When you select timer operation, the remote control automatically transmits the timer signal to the indoor unit at the
specified time. Therefore, keep the remote control in a location where it can transmit the signal to the indoor unit properly.
SET
• If you do not press the SET
button within 30 seconds after setting the time, the setting will be cancelled.
Once you select timer operation mode, the settings are saved in the remote control.
Thereafter, the air conditioner will start operating under the same conditions as if you pressed the
control.
OFF
ON
or
button of the remote
You cannot set the timer when the clock display is flashing.
Follow the instructions in the section “Setting the clock” on page 6 to set the clock, and then set the timer.
11
EN
Combined timer (Setting the ON and OFF timers simultaneously)
OFF timer —> ON timer
(Operation —> Stop —> Operation)
This feature is useful when you want to stop the air conditioner after you go to sleep, and start it again in the morning when you wake
up or you return home.
Example:
To stop the air conditioner and start it again next morning
Setting combined TIMER
Operation
Operation again
OFF
(1) Press the OFF
button to set the OFF timer.
button to set the ON timer.
Stop
ON
(2) Press the ON
(3) Press the SET
SET
button.
ON timer —> OFF timer
(Stop —> Operation —> Stop)
You can use this setting to start the air conditioner when you wake up and stop it when you leave the house.
Example:
To start the air conditioner the next morning and stop it
Setting combined TIMER
Operation
ON
(1) Press the ON
button to set the ON timer.
button to set the OFF timer.
Stop
Stop
OFF
(2) Press the OFF
(3) Press the SET
SET
button.
• The ON or OFF timer function that is closer to the current time is
activated first.
• If the same time is set for both ON and OFF timers, no timer
operation is performed. Also, the air conditioner may stop
operating.
CAUTION
Approximately 3 seconds later, the remote control will
transmit the signal to the indoor unit and a receiving beep
will sound from the indoor unit after you press the
SET
SET
button.
Daily combined timer (setting the ON and OFF timers simultaneously and activating every day.)
This feature is useful when you want to use the combined timers at the same time every day.
Setting combined TIMER
ON
(1) Press the ON
button to set the ON timer.
button to set the OFF timer.
OFF
(2) Press the OFF
(3) Press the SET
SET
button.
(4) After step (3), an arrow mark ( or ) flashes for about 3 seconds. Press the
SET
SET
button during this flashing.
PAP
AUTO
TEMP
• Both arrows (
,
) are shown while the daily timer is activated.
MODE
PRESET
Cancelling timer operation
CLR
Press the CLR
button.
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
Clock display
SWING
CLR
FIX
FAN
SLEEP
During TIMER operation (ON-OFF, OFF-ON, OFF timer), the clock indicator is not shown
so the setting time can be displayed. To view the current time, press the SET button
briefly and the current time will be displayed for about 3 seconds.
c
a
b
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
EN
12
MEMORY/PRESET OPERATION
Use the MEMO button to store a frequently used operation setting for convenience.
Start the air conditioner in the operation mode that you want the remote control to store.
Press the button as shown below while the air conditioner is operating.
a MEMO button
Press this button briefly to ready for storing the setting.
All the icons currently shown flash, except for the clock indicator and mode indicator.
b MEMO button
Hold down the MEMO button for more than 3 seconds while the indicator flashes.
AUTO
PAP
The
mark is shown and the setting is stored.
TEMP
• If you do not press the MEMO button within 3 seconds or if you press another button,
the MEMORY setting is cancelled.
MODE
PRESET
• Operation modes which can be stored with the MEMO button are MODE, Temperature,
FAN, TIMER and Hi POWER.
a
b
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SWING
CLR
FIX
FAN
SLEEP
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
To operate the air conditioner with the setting stored using the MEMO button.
a PRESET button
Press the PRESET button. The setting stored with the MEMO button will be shown
and the air conditioner operates based on the setting.
(A): When the PRESET button is pressed while operation is stopped
• The OPERATION indicator (green or orange) on the display panel of the indoor unit
turns on, and operation starts after approximately 3 minutes.
(B): When the PRESET button is pressed during operation
• The operation mode changes to the setting stored with the MEMO button.
PAP
AUTO
TEMP
• Initial setting:
MODE
PRESET
MODE
: AUTO
Temperature : 22
a
HiPOWER
ECO
MEMO
.
.
.
1 3 5 9H
SWING
CLR
FIX
FAN
OFF
SLEEP
SET
ON
FILTER
CLOCK
RESET
CHECK
13
EN
ADJUSTING AIR FLOW DIRECTION
• Adjust the air flow direction properly. Failure to do so could cause discomfort
and make an uneven room temperature distribution.
• Adjust the vertical air flow using the remote control.
• Adjust the horizontal air flow manually.
Adjusting the vertical air flow
The air conditioner automatically adjusts the vertical air flow direction according
to the operating conditions when AUTO or A mode is selected.
To set a selected air flow direction
Use this function when the air conditioner is operating.
a FIX button
Hold down or briefly press the FIX button on the remote control to move the
louver in the desired direction.
PAP
AUTO
TEMP
• Change the vertical air flow louver direction within the range indicated.
• In subsequent operations, the vertical air flow is automatically set to the
direction that you set the louver using the FIX button.
MODE
PRESET
HiPOWER
ECO
MEMO
.
.
.
1
3
5 9H
a
To automatically swing the air flow direction
Perform this function when the air conditioner is operating.
a SWING button
SWING
CLR
FIX
FAN
SLEEP
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
Press the SWING button on the remote control.
• To stop the function, press the SWING button.
• To change the swing direction, press the FIX button.
CAUTION
• The FIX and SWING buttons will be disabled when the air conditioner is not
operating (including when ON TIMER is set).
• Do not operate the air conditioner for an extended period of time with the air
flow direction set downward during the cooling or dry operation. Otherwise,
condensation may occur on the surface of the vertical air flow louver and
cause water dripping.
AUTO
PAP
TEMP
MODE
PRESET
• Do not move the vertical air flow louver manually. Always use the FIX button.
If you move the louver manually, it may malfunction during operation.
If the louver malfunctions, stop the air conditioner once, and restart.
• When the air conditioner is started immediately after it was stopped, the
vertical air flow louver might not move for about 10 seconds.
HiPOWER
ECO
MEMO
.
.
.
5 9H
1
3
SWING
CLR
FIX
FAN
SLEEP
a
SET
ON
OFF
FILTER
CLOCK
RESET
CHECK
Adjusting the horizontal air flow
Preparation:
• Grasp the lever on the horizontal air flow louver and move them to adjust the air
flow direction as required.
• You can adjust the air flow at the left and right locations of the grilles.
EN
14
AUTO RESTART OPERATION
This air conditioner is equipped with an automatic restarting function which allows the air conditioner to resume without the use of the
remote control under the operating settings in the event of a power shutdown. Operation resumes without warning three minutes after
power is restored.
INFORMATION
The AUTO RESTART OPERATION is not set to work at factory shipment, and so it is necessary to set it to this function if
required.
HOW TO SET AUTO RESTART
To set the auto restart function, proceed as follows:
The power supply to the unit must be on. The function will not be set if the power is off.
To enable the auto restart function, hold down the RESET button for 3 seconds.
The air conditioner receives the setting and beeps 3 times. The system now restarts
automatically. The auto restart setting is activated.
(1) When the air conditioner is in stand-by (not running).
Hold down the RESET button for more than 3 seconds.
• The air conditioner starts to operate. The green indicator turns on.
• After about 3 seconds, the air conditioner beeps 3 times.
The indicator changes from green to orange.
• The air conditioner is operating.
If the air conditioner is not required to run at this time, push the RESET button
again or use the remote control to stop the air conditioner.
(2) When the air conditioner is operating.
RESET button
Hold down the RESET button for more than 3 seconds.
• The air conditioner stops operating. The green indicator turns off.
• Three seconds after pushing the button, the air conditioner beeps 3 times.
• The air conditioner stops.
If you do not need the air conditioner to stop at this time, use the remote control to restart the air conditioner. During the
subsequent operation, the orange indicator is turned on.
• The auto restart operation will not accept a command if timer operation with the remote control is activated.
• After restarting the air conditioner by the AUTO RESTART OPERATION, the louver swing (AUTO) operation does not resume.
HOW TO CANCEL AUTO RESTART
To cancel the auto restart operation, proceed as follows:
Repeat the setting procedure. The air conditioner receives the setting and beeps three times.
The air conditioner now needs to be manually restarted with the remote control after the main supply is turned off.
The auto restart setting is cancelled.
(1) When the air conditioner is in stand-by (not running).
Hold down the RESET button for more than 3 seconds.
• The air conditioner starts to operate.
The orange indicator will turn on.
• After about 3 seconds, the air conditioner beeps 3 times.
The indicator changes from orange to green.
• The air conditioner is operating.
If the air conditioner is not required to run at this time, push the RESET button
again or use remote control to stop the air conditioner.
(2) When the air conditioner is operating.
Hold down the RESET button for more than 3 seconds.
• The air conditioner stops operating.
The orange indicator is turned off.
• After about 3 seconds, the air conditioner beeps 3 times.
RESET button
• The air conditioner stops.
If you do not need the air conditioner to stop at this time, use the remote control to
restart the air conditioner.
During subsequent operation, the green indicator is turned on.
15
EN
HOW THE AIR CONDITIONER WORKS
Automatic Operation
As shown in Figure 1, Automatic Operation mode selects the operation based on the room temperature data (Ta) when operation
begins.
Room temperature when operation begins
or when selected again
Ta
Cooling operation
Ts+1
Ts
Fan operation
Ts–1
Heating operation
Figure 1
The operation mode is selected again after the compressor has remained stopped for 15 minutes.
Hi POWER operation
When you press the Hi POWER button during cooling, heating or A operation, the air conditioner starts the following operation.
• Cooling operation
The cooling operation is performed lower than the temperature setting.
When the room temperature is above the temperature setting, the air flow is directed downward. The fan speed is also set to high*.
Once the room temperature is within 1°C of the temperature setting, the air flow is returned to its regular direction to cool the entire
room with maximum efficiency.
* The noise level raises, according to the fan speed.
• Heating operation
The heating operation is performed at 2°C higher than the temperature setting.
ECO operation
When you press the ECO button during cooling, heating or A operation, the air conditioner starts the following operation.
The fan speed is controlled automatically.
• Cooling operation (
)
In the minimum operation zone, where the air conditioner is operated at minimum capacity, overcooling is prevented by raising the
temperature setting.
The room temperature is thus regulated between the minimum operation zone and the temperature setting.
• Heating operation (
)
In the minimum operation zone, where the air conditioner is operated at minimum capacity, overheating is prevented by lowering the
temperature setting.
The room temperature is thus regulated between the temperature setting and the minimum operation zone.
EN
16
DRY operation (
)
The dry mode automatically selects the cooling dry operation based on the difference
between the temperature setting and the actual room temperature.
The fan speed indicator shows AUTO, and low speed is used.
HINTS FOR ECONOMICAL OPERATION
Chilly
Maintain room temperature at a comfortable level
Control
Clean the air filters
Clogged air filters impair the performance of the air conditioner.
Clean them once every two weeks.
Please clean
Never open doors and windows more than is necessary
To keep cool or warm air in the room, never open doors and
windows more than is necessary.
Use the timer
effectively
Window curtains
During cooling operation, close the curtains to avoid direct
sunlight.
During heating operation, close the curtains to keep the heat in.
Use the timer effectively
Set the timer for the desired operating time.
Allow uniform circulation of room air
Adjust the air flow direction for even circulation of room air.
Blows upward
Air flow adjustment
Blows downward
TEMPORARY OPERATION
I cannot find
the remote
control
Temporary operation
This function is used to operate the unit temporarily in case you misplace the remote
control or the batteries are used up.
• Push the RESET button to start the air conditioner.
• While the temporary operation is activated, the remote control operation is disabled.
• Hold down the button for 10 seconds to start the cooling operation.
A temporary
operation feature is
provided!
17
EN
USUAL MAINTENANCE
WARNING
Before you clean the air conditioner, be sure to turn off the circuit breaker or main power switch.
Wipe with a dry cloth
Cleaning of indoor unit and remote control
CAUTION
• Use a dry cloth to wipe the indoor unit and remote control.
• When the air conditioner is extremely dirty, use a cloth dipped in cold water to wipe the indoor
unit.
Thinner
• Never use a damp cloth on the remote control.
• Do not use a chemical-based duster for wiping or leave such materials on the unit for extended
periods of time. Doing so could damage or cause the surface of the unit to fade.
• Do not use benzine, thinner, polishing powder, or other solvents for cleaning.
These can cause the plastic surface to crack or deform.
Cooling with
high
temperature
setting.
When not using the unit for at least 1 month
(1) Perform fan operation for three to four hours to dry the inside of the unit.
• If a high temperature setting is used with cooling operation, fan operation is performed.
(2) Stop the air conditioner and turn off the circuit breaker.
(3) Clean the air filters.
(4) Remove the batteries from the remote control.
Check before operation
CAUTION
Air
filter
• Check that the air filters are installed.
• Check that the air outlet and inlet of the outdoor unit are not blocked.
Cleaning the air filter
Clean the air filters every 2 weeks.
The performance of the air conditioner will degrade if the air filters are covered with dust.
Clean the air filters as often as possible.
Preparation:
1. Turn off the air conditioner using the remote control.
2. Open the air inlet grille.
1
2
3
Open the air inlet grille.
Lift the air inlet grille up to the horizontal position.
Grasp the left and right handles of the air filter and lift it up slightly, and then pull it downward to
take it out from the filter holder.
Filter holder
Use a vacuum cleaner to remove the dust from the filters or wash them with water.
After washing the air filters, dry them in the shade.
EN
18
4
5
Insert the top section of the air filter so that its right and left
edges fit on the indoor unit and it is firmly set.
Close the air inlet grille.
* If the FILTER indicator on the indoor unit is shown, press the
FILTER button on the remote control or the RESET button
on the indoor unit to turn off the indicator.
Filter holder
Cleaning the air inlet grille
Preparation:
1. Turn off the air conditioner using the remote control.
Arm
2. Open the air inlet grille.
1
2
Remove the air inlet grille.
Hold the two sides of the air inlet grille and open upwards.
Move the center arm to the left and remove the grille.
Wash it with water using a soft sponge or towel.
(Do not use a metallic scrubbing brush or other hard brushes.)
• Use of such hard objects will cause scratches on the surface of the grille and
the metal coating to peel off.
• If extremely dirty, clean the air inlet grille with a neutral kitchen detergent and
rinse it off with water.
3
4
Wipe off the water from the air inlet grille and dry it.
Fit the left and right arms of the air inlet grille to the shafts on the two sides of the
air conditioner and push them in completely, and then push in the center arm.
Left and
right arms
Center arm
5
Check that the center arm has been completely inserted and close the air inlet
grille.
• Push the arrow locations (four) at the bottom of the air inlet grille to check that
the grille is completely closed.
NOTE
Cleaning and maintenance of the indoor/outdoor units are strongly recommended
for air conditioning systems which are used regularly.
Failure to clean the indoor/outdoor units regularly will result in poor cooling
performance, icing, water leakage and even premature compressor failure.
Zeolite-3G filter
Zeolite-plus filter
19
EN
SPECIAL MAINTENANCE
Attaching the Zeolite-plus filter and Zeolite-3G filter
• After installing the air conditioner, attach the supplied Zeolite-plus
filter and Zeolite-3G filter.
INFORMATION
• It is recommended that you replace the filters once
about every six years.
Preparation:
Deodorizing performance will drop when there are
severe stains due to extended periods of usage
such as due to tar accumulation from cigarette
smoke.
1. Turn off the air conditioner using the remote control.
Items sold separately
Zeolite-plus filter
(RB-A607DE)
Zeolite-3G filter
(RB-A608DE)
1
2
Open the air inlet grille.
Lift up the air inlet grille until it clicks into place.
Take off the air filter from the left side.
Grasp the left and right handles of the air filter and lift up slightly and then pull downward to
remove the filter from the filter holder.
3
4
Attach the Zeolite-plus filter and Zeolite-3G filter to the front panel.
When attaching new filters, remove the Zeolite-plus filter and Zeolite-3G filter from the bag,
and then insert the filters with the Zeolite-plus filter on the top.
Attach the air filter, and then close the air inlet grille.
Cleaning the Zeolite-plus filter and Zeolite-3G filter
• Clean the filters when you clean the dust collecting unit. (Clean approximately once every six
months.)
Preparation:
1. Turn off the air conditioner using the remote control.
1
2
Open the air inlet grille.
Lift up the air inlet grille until it clicks into place.
Grasp the left and right handles of the air filter and lift up slightly and then pull downward to
remove the filter from the filter holder.
3
4
Remove the Zeolite-plus filter and Zeolite-3G filter from the front panel.
Wash the Zeolite-plus filter and Zeolite-3G filter in water, and then drain.
• If the filters are dirty with dust and dirt, use a vacuum cleaner to remove the dirt before
washing with water. Also, be sure to always use clean water when washing. If dirty water is
used, the debris in the water can adhere to the filters.
• Do not rub the filter surface.
• In the final of the water washing, be sure to always rinse the filter with clean water.
• If the filter is particularly dirty, add a neutral detergent at the standard concentration and then
rinse with clean water until there are no more soap bubbles.
• Drain gently after washing with water.
5
6
Allow the Zeolite-plus filter and Zeolite-3G filter to dry in the sun.
• It takes about six hours for the filters to dry in direct sunlight.
Attach the air filter, and then close the air inlet grille.
EN
20
Cleaning the air ionizer
• Clean the air ionizer when you clean the dust collecting unit. (Clean approximately once
every six months.)
Preparation:
1. Turn off the air conditioner using the remote control.
2. Turn off the power supply.
WARNING
Touching the ends of the metal pins inside the air ionizer (dark blue) can result in an
electrical shock.
1
2
Fully open the vertical air flow louvers by hand.
Remove the dust on the air ionizer.
• Use a toothbrush to rub the ends of the metal pins inside the air ionizer (dark blue)
three or four times.
• Do not use cotton swabs or other objects with fluff.
3
Close the vertical air flow louvers.
Cleaning the dust collecting unit
• Clean the dust collecting unit when the FILTER indicator (orange) turns on.
(This indicator turns on after PAP operation of about 1000 hours.)
• Pressing the RESET buttons turns off the FILTER indicator.
• Perform cleaning about once every six months.
• Even if the FILTER indicator does not turn on, clean the dust collecting unit whenever the
unit makes a humming, clicking, or buzzing sound. If the indicator turns on during the
night, the air conditioner can still be used until the morning without a problem, but be sure
to perform cleaning as soon as possible.
Preparation:
1. Turn off the air conditioner using the remote control.
2. Turn off the power supply.
1
2
3
Open the air inlet grille.
Lift up the air inlet grille until it clicks into place.
1
Grasp the left and right handles of the air filter and lift up slightly and then pull
downward to remove the filter from the filter holder.
2
Take out the dust collecting unit.
• Grasp the handles, and then pull out as shown in aand b.
21
EN
4
Wash and then dry.
(1) Soak in hot water at 40 to 50°C for about 10 to 15 minutes. If the staining is particularly
severe, use a washing detergent compound (weak basic or neutral) at 10 to 15 times
the standard concentration.
(2) Rub up and down, and rub left and right. Also, rub the surface gently with a sponge.
(3) Rinse with running water.
(4) Shake thoroughly, and allow the unit to drain.
(If oil or smoke strains are particularly hard to remove, repeat steps (1) to (4) two or
three times.)
(5) Allow to dry thoroughly in the shade.
CAUTION
• Never use any products marked as “bleach”.
• Do not attempt to disassemble the unit.
• Do not rub with a scrubbing brush or similar implement.
• Do not dry with a hair dryer or other appliance that uses hot air. (The heat can cause the unit
to deform.)
• After cleaning, wait until the unit is completely dried before attaching. The FILTER indicator
may turn on if the unit is used while wet.
5
6
Attach the dust collecting unit.
• Grasp the handles, and then insert as shown in aand b. Insert into the right and left
guide rails, and then press in the direction of bafter it is all the way in.
• Press both ends of the dust collecting unit in the direction of cuntil the protrusions on
both sides of the dust collecting unit are completely inserted into the holders.
3
2
Attach the air filter, and then close the air inlet grille.
1
EN
22
AIR CONDITIONER OPERATION AND PERFORMANCE
Three-minute protection feature
A protection feature is provided that prevents the air conditioner from being activated for approximately 3 minutes when it is restarted
immediately after operation or when the power supply switch is set to on. This is used to protect the machine.
Heating characteristics
Preheating operation
The air conditioner does not deliver warm air immediately after it is started.
Warm air flows out after approximately 5 minutes when the indoor heat exchanger has warmed up.
Warm air control
When the room temperature reaches the temperature setting, the fan indoor speed is automatically reduced.
The outdoor unit is stopped at this time.
Defrosting
If frost has formed on the outdoor unit during the heating operation, defrosting is started automatically (for approximately 5 to 10
minutes) to maintain the heating effect.
• The fans in both the indoor and outdoor units stop during the defrost operation.
• During the defrost operation, defrosted water is drained from the bottom plate of the outdoor unit.
Heating capacity
In the heating operation, heat is absorbed from outdoors and released into the room. That is called the heat pump system. When the
outdoor temperature is too low, usage of another heating apparatus in combination with the air conditioner is recommended.
Consideration for accumulated snow
Select the position for the outdoor unit where it will not be subjected to snow drifts, accumulation of leaves or other seasonal debris. It
is important that the air flow of the outdoor unit is not blocked as this will result in reduced heating or cooling performance. During the
heating mode and at sub-zero temperatures, the water drained off the outdoor unit as a result of the automatic defrost may
accumulate and freeze. It is important that adequate drainage or a soak-way be provided.
Power failure
Power failure during operation stops the unit completely.
• The OPERATION indicator (green) on the indoor unit starts flashing when power is restored.
• To restart operation, push the
• Lightning or a car wireless telephone operating nearby may cause the unit to malfunction. Turn the power supply switch off and then
on again. Push the button on the remote control to restart.
button on the remote control.
Air conditioner operating conditions
For proper performance, operate the air conditioner under the following temperature conditions.
Cooling operation
Outdoor temperature: 10°C to 43°C
Room temperature: 21°C to 32°C
CAUTION
Room relative humidity — less than 80%. If the air conditioner operates outside this
range, the surface of the air conditioner may attract condensation.
Heating operation
Dry operation
Outdoor temperature: –15°C to 24°C
Room temperature: Less than 28°C
Outdoor temperature: 10°C to 43°C
Room temperature: 17°C to 32°C
If the air conditioner is used in conditions other than above, the safety protection functions may be activated.
23
EN
TROUBLESHOOTING
CAUTION
If any of the following conditions occur, stop the air conditioner immediately, turn off the main power switch and contact the
dealer.
• The indicators flash at short intervals (5 Hz). Reset the circuit breaker 2 to 3 minutes after the power main switch is turned off.
Despite the resetting operation, the indicators still continue turning on and off.
• Switch operation is erratic.
• The main power fuse often blows, or the circuit breaker is often activated.
• Foreign matter or water has fallen inside the air conditioner.
• Any other unusual conditions are observed.
Before asking for servicing or repairs, check the following points.
Inoperative
• The power main switch is turned off.
• The circuit breaker is activated to cut off the power supply.
• The main power fuse has blown.
• The electric current has stopped.
• The batteries in the remote control used up.
• The ON timer is set.
• As a protective mechanism for the air conditioner, it does not operate for three
minutes immediately after restarting operation or turning on the main power.
Poor cooling or heating performance
• The air inlet or outlet of the outdoor unit is blocked.
• Doors or windows are opened.
• The air filter is clogged with dust.
• The louver is not at the correct position.
• The fan speed is set to low.
• The air conditioner is set to the DRY or ECO mode.
• The temperature setting is too high (during cooling operation).
• The temperature setting is too low (during heating operation).
EN
24
Before asking for servicing or repairs, check the following points.
Condensation forms on the back of the indoor unit.
• Condensation on the back of the indoor unit is automatically collected and drained out.
Indoor unit or outdoor unit makes a strange noise.
• When the temperature changes sharply, the indoor or outdoor unit may make a strange
noise (such as a tit-tack noise or flowing noise) because of the expansion/contraction of
parts or change in refrigerant flow.
The room air is smelly.
A bad odor comes from the air conditioner.
• Smells absorbed in the wall, carpet, furniture, clothing, or furs are coming out.
• During PAP operation, a small amount of ozone is produced, and you might notice the
smell.
The OPERATION indicator turns on and off.
• The indicator turns on and off (1 Hz) when power is restored after a power failure or when
the power main switch is set to on. Reset the circuit breaker to ON.
Frost forms on the outdoor unit during heating operation.
Water is drained from the outdoor unit.
• Frost sometimes forms on the outdoor unit during heating operation. In that case, the unit
automatically performs defrosting (for 2 to 10 minutes) for improving the heating efficiency.
• In the defrosting operation, the airflow from both the indoor and outdoor units stops.
• A hiss sound is heard when the flow of the refrigerant is changed for defrosting.
• The water resulting from automatic defrosting during the heating operation is drained from
the outdoor unit.
The air flow changes even though the FAN button is not set to the AUTO mode.
• When the temperature of the blown air goes down during heating operation, the air
conditioner automatically changes or stops the air flow from the indoor unit so that the
people in the room do not feel chilly.
A white mist of chilled air or water is generated from the outdoor unit.
• Steam is sometimes generated from the indoor unit during cooling operation or the
outdoor unit during defrosting operation.
Automatic operation of vertical air flow louvers
• When the room temperature or outdoor temperature is high during the heating operation,
the vertical air flow louvers close once and then set themselves automatically to the
original position setting again.
25
EN
Before asking for servicing or repairs, check the following points.
The FILTER indicator turns on.
• This indicator turns on after PAP operation has been performed for approximately 1000
hours.
• The indicator may turn on if the front panel is not firmly closed.
• The indicator may turn on if the dust collecting unit is not securely attached.
Sounds made from the indoor unit
• The dust collecting unit may make a humming, clicking, or buzzing sound when it is dirty.
• When the power is turned on or the air conditioner is stopped, the vertical air louvers may
make a rattling sound or shuttling sound.
• Some parts may expand or shrink due to temperature fluctuations, and this can result in a
slapping sound.
• When the refrigerant is flowing, a hissing sound or gurgling sound can result.
• A buzzing sound is sometimes made from the air ionizer.
• A hissing sound can be made when the air conditioner is switched to defrosting operation
during heating operation.
Sounds made from the outdoor unit
• A rustling sound can be made when the air conditioner is switched to defrosting operation
during heating operation.
EN
26
SPECIFICATIONS
Type
Reverse cycle, Split type
Model
Indoor Unit
Outdoor Unit
RAS-10JAVP-E
Indoor Unit
Outdoor Unit
RAS-10JKVP-E
RAS-13JKVP-E
RAS-13JAVP-E
Power supply
220 – 240 V~, 50 Hz
220 – 240 V~, 50 Hz
220 V~, 60 Hz
220 V~, 60 Hz
Cooling capacity
Heating capacity
Cooling current
Cooling power
Heating current
Heating power
(kW) CAPA.
(kW) CAPA.
2.5
3.2
3.5
4.2
(A)
(W)
(A)
AMP
0.15
30
2.58 – 2.35
0.15
30
4.40 – 4.02
WATT.
AMP.
540
3.44 – 3.14
720
920
5.07 – 4.63
1060
780
0.15
30
0.15
30
(W)
WATT.
Width (mm)
Height (mm)
Depth (mm)
(kg)
790
250
208
10
780
790
250
208
10
Dimensions
Net weight
550
550
270
270
38
38
• These specifications are subject to change without notice for the purpose of incorporating technical improvements.
The specified air-conditioning performance is based on the data determined under the following conditions.
For cooling
For heating
Air inlet temperature °C
Indoor coil assembly Outdoor coil assembly
Air inlet temperature °C
Indoor coil assembly Outdoor coil assembly
Dry bulb
27
Wet bulb
19
Dry bulb
35
Wet bulb
24
Dry bulb
20
Wet bulb
—
Dry bulb
7
Wet bulb
6
27
EN
TROUBLESHOOTING (Remote Control)
Before asking for servicing or repairs, check the following points.
Settings Cannot be Changed
Symptoms
Causes
Description and Remedy
The fan speed cannot be
changed.
• Check whether the MODE indicated
on the display is “AUTO”.
When automatic mode is selected, the
air conditioner automatically selects
the fan speed.
AUTO
• Check whether the MODE indicated
on the display is “ : DRY”.
When dry operation is selected, the air
conditioner automatically selects the
fan speed. The fan speed can be
selected during “
HEAT” and “A”.
COOL”,
: DRY
“
The Display Goes Off
Symptoms
Causes
Description
The indicators on the display
are not shown after a short
time.
• Check whether the timer operation is
over when the OFF TIMER is shown
on the display.
The air conditioner stops since the
setting time has elapsed.
The TIMER display turns off
after a certain period of time.
• Check whether the timer operation
has started when the ON TIMER is
shown on the display.
When the time reaches the time
setting for the ON timer operation, the
air conditioner starts to operate
automatically and the ON timer display
turns off.
: ON
The Signal Receiving Tone Does Not Sound
Symptoms
Causes
Description
No receiving tone is made from
the indoor unit even when the
button is pushed.
• Check whether the signal transmitter
of the remote control is properly
pointed towards the receiver of the
Point the signal transmitter of the
remote control towards the receiver of
the indoor unit, and then press the
button repeatedly.
indoor unit when the
pushed.
button is
EN
28
DECLARATION OF CONFORMITY
We, TOSHIBA CARRIER CORPORATION, 336 Tadewara, Fuji-shi, Shizuoka-ken, 416-8521,
Japan, declare under our responsibility that the product, Household split type Room Air
Conditioner, to which this declaration relates is in conformity with the provisions of Council
Directive 89/336/EEC Electromagnetic Compatibility and 73/23/EEC Low Voltage Directive.
E075003383-b
Printed in Japan
|