Panasonic Dp 2010e User Manual

Digital Imaging Systems  
Operating Instructions  
DP-1810P  
with Options  
(For Copier)  
DP-2010E  
with Options  
Model No.  
DP-1810P/2010E  
J
?
I
Before operating this equipment, please read these instructions completely and keep these operating  
instructions for future reference.  
English  
Operation Chart  
Common Features and Usage  
I Basic Operation  
Original  
1 2 3 4 5  
Original Size  
(Reduction/  
Enlargement  
Only)  
Copy Size  
(Reduction/ of Copies  
Enlargement  
Number  
Press  
START  
Place the  
Original  
Load Paper  
Turn the Power  
Switch On  
Only)  
I Position of the Original  
From ADF (or i-ADF)  
From Platen  
Original Guide  
CPlace originals face down on the  
platen or face up on the ADF.  
CIf the original is not positioned  
properly, a portion of the original  
may not be copied.  
CFor originals smaller than invoice  
size, position the original within the  
area of INVOICE and select invoice.  
INV  
INV  
LTR  
LGL  
LDR  
INV  
ADFTray  
INV  
LTR  
LGL  
Original Guides  
Adjust to the originals width  
LTR  
LDR  
I Commonly Used Functions and Operating Procedures  
Full Size  
(See page 12)  
Makes a copy that is the same  
size as the original  
1 4 5  
Reduction or Enlargement  
Copies the original at a fixed  
reduction or enlargement ratio  
(See page 13)  
1 2 3 4 5  
I Memory Capacity  
When the memory becomes full during original scanning, the message “OUT OF MEMORY”  
“CONTINUE? 1:YES 2: NO” will be displayed in the message display. In this case, follow the  
operating instruction in the message display.  
When additional memory is required, consult with an authorized servicing dealer.  
3
Energy Star  
As an ENERGY STAR® Partner, Panasonic has determined that this product meets the  
ENERGY STAR® guidelines for energy efficiency.  
This voluntary program specifies certain energy consumption and usage standards. This  
product will automatically power downafter a specified period of non-use. The use of this  
ENERGY STAR® compliant product will reduce energy consumption and ultimately benefit the  
environment.  
The default functions can be adjusted depending on your office requirements.  
Please ask your authorized Panasonic dealer for more details.  
4
Table of Contents  
Getting To KnowYour Machine  
Operation Chart .............................................................................................................................. 3  
I Common Features and Usage..............................................................3  
Energy Star ..................................................................................................................................... 4  
Before Starting  
Precautions ..................................................................................................................................... 7  
I ForYour Safety .....................................................................................8  
I Handling ...............................................................................................8  
I Toner and Paper ...................................................................................8  
I Ventilation .............................................................................................8  
I Installation ............................................................................................9  
Control Panel ................................................................................................................................ 10  
Making Copies  
Basic Copy .................................................................................................................................... 12  
I Full Size Copying ................................................................................12  
I Reduction or Enlargement Copying ....................................................13  
I Zoom Copying ....................................................................................14  
I Using the Sheet Bypass .....................................................................15  
Creative Features ......................................................................................................................... 16  
I 2 in 1 Copy .........................................................................................16  
I 2 Page Copy .......................................................................................17  
I Book/Edge/Margin ..............................................................................18  
I 2-Sided/1-Sided Copy.........................................................................19  
I 1 \ 2/2 \ 1/2 \ 2 Copy....................................................................20  
I Book \ 2 Copy ..................................................................................21  
I Job Memory .......................................................................................22  
I Sort Copy ...........................................................................................23  
Other Features .............................................................................................................................. 24  
I Energy Saver/Interrupt Mode..............................................................24  
I Skyshot Mode.....................................................................................25  
Combined FunctionTable ............................................................................................................ 27  
Function ........................................................................................................................................ 28  
I Checking the Copiers Total Counter ...................................................28  
I General Functions ..............................................................................29  
I Copier Settings ...................................................................................30  
I General Functions for Key Operator ...................................................31  
I Copier Settings for Key Operator ........................................................32  
I Function Setting..................................................................................33  
I Function Setting for Key Operator.......................................................34  
5
Table of Contents  
Options  
Accessories .................................................................................................................................. 39  
I Components .......................................................................................39  
I Automatic Document Feeder ..............................................................40  
Problem Solving  
Problem Solving ........................................................................................................................... 42  
I Adding Paper (J) ...............................................................................42  
I Adding the Toner and Replacing Toner Waste Container (?) .............43  
I Removing a Misfed Paper...................................................................45  
Troubleshooting ........................................................................................................................... 52  
I Before Calling Service ........................................................................52  
I User Error Codes (U Code) ................................................................54  
Others  
Specifications ............................................................................................................................... 55  
Options and Supplies................................................................................................................... 57  
6
Precautions  
For Your Safety  
I Laser Safety  
LASER SAFETY  
This unit employs a laser. Only qualified service personnel should  
attempt to service this device due to possible eye injury.  
CAUTION:  
USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE  
PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY  
RESULT IN HAZARDOUS RADIATION EXPOSURE.  
I Caution Labels  
(Digital copier with ADF option)  
(Digital copier with ADF option)  
Manufacturer’s name and address  
Factory ID  
7
Precautions  
Handling  
I Do not look directly at the exposure lamp when  
copying.  
I Do not turn the power switch Off or open the front  
panel during copying.  
CDo not drop paper clips or other metal objects into  
the copier.  
Toner and Paper  
I Store toner, drum and paper in cool areas with low  
humidity.  
CUse high quality 16 24 lb (60 90 g/m2) [Sheet  
Bypass: 15 34 lb (56 128 g/m2)] paper.  
CFor optimum performance, it is recommended that  
only Panasonic Brand supplies are used in the  
copier.  
Ventilation  
I The copier should be installed in a well-ventilated  
area to minimize the ozone density in the air.  
8
Precautions  
Installation  
I The copier should not be installed in areas with the  
following conditions:  
CExtremely high or low temperature and humidity.  
Ambient conditions  
Temperature:  
50 86°F (10 30°C)  
Relative humidity: 30 80 %  
CWhere temperature and humidity can change  
rapidly, causing condensation.  
CDirect exposure to sunlight.  
CDirectly in the air conditioning flow.  
CIn areas of high dust concentration.  
CIn areas of poor ventilation.  
CIn areas with chemical fume concentration.  
CIn areas with extreme vibration.  
CWith unstable or uneven conditions (floors, etc.).  
I The maximum power consumption is 1.2 kW.  
A properly wired (grounded), dedicated, 15 A, 120 VAC outlet is required.  
Do not use an extension cord.  
The power cord on this equipment must be used to disconnect the main power.  
Please ensure that the socket outlet is installed near the equipment and is easily accessible.  
FCC WARNING For U.S.A.  
FCC WARNING:  
This equipment has been tested and found to comply with the limits for a Class A digital device,  
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable  
protection against harmful interference when the equipment is operated in a commercial  
environment.This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual, may cause harmful  
interference to radio communications. Operation of this equipment in a residential area is likely  
to cause harmful interference in which case the user will be required to correct the interference  
at his/her own expense.  
The user could lose the authority to operate this equipment if any unauthorized changes or  
modifications are made to this equipment.  
9
Control Panel  
(For DP-2010E only)  
No  
Contents  
Refer to  
2 in 1 Key  
#
Page 16  
CFrom two 1-sided originals, side by side, to 1-sided copies.  
2 Page Copy Key  
$
%
CCopying two facing pages on a ledger size original on two separate  
Page 17  
Page 23  
letter size sheets.  
Sort Key  
CWhen using Electric Sorting Mode. Optional memory is required.  
&
(
)
MARGIN Key CShifts the image to the right or left.  
Page 18  
Page 18  
Page 18  
EDGE Key  
BOOK Key  
CCreates a blank edge.  
CEliminates dark inner binding shadows.  
Photo;Text/Photo;Text Keys  
CSelect the type of original(s) for image density adjustment.  
PHOTO  
: Originals are mainly composed of photo.  
*
Page 12  
TEXT/PHOTO: Combined originals with text and photo.  
TEXT : Originals are mainly composed of text.  
+
-
Exposure Keys (DARKER, LIGHTER)  
SET Key CSet the present selection.  
Page 12  
——  
FUNCTION Key  
CUse when changing the paper size, initial values for functions (default  
values) and key operator settings.  
.
Pages 28 37  
/
0
1
CLEAR Key CClears the copy count in the display.  
——  
Page 24  
——  
ENERGY-SAVER Key  
CCan save power while the copier is not in use.  
RESET Key CResets all features to the initial power-on state.  
CThe Control Panel displayed above shows only copier functions. Please refer to the  
appropriate operating instructions for other control panel functions or in the Panasonic  
Document Management System CD-ROM for the Printer control panel functions.  
CThe illustration above shows the DP-2010E control panel.  
NOTE  
10  
Control Panel  
LCD Display  
Warning Indications  
J Add Paper  
? Add Toner  
I Misfeed  
2 Call Service  
For DP-1810E  
No  
Contents  
CStops the copy run.  
CUsed to start an operation.  
Refer to  
——  
2
3
STOP Key  
START Key  
——  
INTERRUPT Key, MEMORY IN Key, M1/M2 Keys  
CInterrupt Key interrupts other copy or print jobs while making copies.  
4
Pages 22, 24  
CMemory In Key registers two copy jobs for recall at a later time.  
C
M1/M2 Keys are used to store a Job in Memory or to recall a Job stores in Memory.  
5
6
Cursor Keys CSelect copy ratio and function modes using (G or F).  
——  
——  
PAPER TRAY Key  
COPY SIZE Key  
CUsed to select the paper tray manually.  
7
——  
C
Used to select Reduction/Enlargement only.For additional details, see page 13.  
ORIGINAL SIZE Key  
Used to select the original size manually. For additional details, see page 13.  
8
9
:
——  
——  
——  
C
PRINT Key CWhen selecting the Printer ON/OFF Line.  
2-Sided/1-Sided Copy Key  
C Used to select 1 \ 2, 2 \ 2 and 2 \ 1, Book \ 2 copying  
CThe Control Panel displayed above shows only copier functions. Please refer  
to the appropriate operating instructions for other control panel functions or in  
the Panasonic Document Management System CD-ROM for the Printer  
control panel functions.  
NOTE  
11  
Basic Copy  
Full Size Copying  
I Copying the Same Size Originals (1:1)  
Copy size is automatically selected.  
ORIGINAL SIZE Key CLEAR Key  
1
2 3  
Number of Copies*  
Place the Original  
Press START**  
Up to 999  
LCD Display (Sample)  
READY TO COPY  
COPIES:001  
Select the Original Size on units  
without the ADF/i-ADF Option.  
I Manually Selecting Exposure Control or Original Type  
# Select the Original Type  
PHOTO  
:Originals are mainly composed of photo.  
TEXT/PHOTO:Combined originals with text and photo.  
TEXT :Originals are mainly composed of text.  
$ Select Exposure Control  
Press the DARKER/LIGHTER keys to adjust the exposure.  
Use Clear key when canceling the copy count.  
NOTE  
While the copier is warming up, you may position your original on the copier, enter  
your copy job selections and press the Start key. The COPY JOB RESERVED  
indicator displays until the warm up cycle is completed and the copy job is  
automatically started.  
∗∗  
12  
Basic Copy  
Reduction or Enlargement Copying  
I Copying with Preset Ratios  
RESET  
1 2 3 4 5  
Place the  
Original  
Select the  
ORIGINAL SIZE  
Number of  
Copies  
Press  
START  
Select the COPY  
SIZE  
Example: Reduction  
Original size  
Copy size  
LEDGER  
LETTER  
LDR ->LTR  
B
[LTR  
B
]
ZOOM: 65% COPIES:001  
The correct ratio is automatically selected.  
Reduction and enlargement ratios (%)  
Copy Size  
Ledger Legal Letter Invoice  
Original  
Size  
Ledger  
Legal  
100  
121  
129  
200  
77  
65  
79  
50  
61  
100  
100  
155  
Letter  
100  
129  
65  
Invoice  
100  
CWhen changing the paper tray, press the  
PaperTray key.  
CIf the desired copy size is different from the paper size loaded in the paper  
tray, use the sheet bypass. (See page 15)  
NOTE  
CPress the RESET key to cancel all job settings.  
13  
Basic Copy  
Zoom Copying  
I Zoom  
RESET  
Copies with variable zoom ratios from 50 % to 200 % in 1 % increments.  
1 2 3 4 5  
Number  
of Copies  
Place the  
Original  
Select ORIGINAL  
SIZE  
(without using  
Press  
START  
Press Cursor (G or F)  
keys to select Zoom Ratio  
ADF/i-ADF)  
B
LTR ->LTR  
B
[LTR  
B
]
ZOOM:125% COPIES:001  
(Example: 125 % Zoom)  
CWhen changing the paper size after setting the zoom ratio, please use the paper tray  
ATTENTION  
NOTE  
key.  
CPress the RESET key to cancel all job settings.  
14  
Basic Copy  
Using the Sheet Bypass  
I Copying on Special Paper, etc.  
Place the original.  
Open the sheet bypass.  
1
Sheet  
Bypass  
Pull out the sheet bypass tray  
until it stops.  
(For Ledger size only)  
2
3
# Place the sheets of paper into  
the tray. (approximately up to  
50 Letter size sheets/20 lb)  
Do not fill above.  
Insert the paper until it stops.  
Side Guides  
$ Adjust the side guides.  
Incorrect adjustment may cause the  
paper to wrinkle, misfeed or skew.  
Press START.  
CDo not feed curled paper through the sheet bypass to avoid misfeed.  
ATTENTION  
NOTE  
CAdjust the side guides properly to avoid skewing, wrinkling or misfeeding.  
15  
Creative Features  
2 in 1 Copy  
I 2 in 1 Copy  
From two 1-Sided originals, side by side, to 1-Sided pages.  
1 \ 2 (Layout)*  
1 \ 2 (Layout)*  
2 \ 1 (Layout)*  
2 \ 1 (Layout)*  
Landscape (Orientation)*  
Portrait (Orientation)*  
I Procedure  
ADF/i-ADF  
Face-Up  
( )  
COPY SIZE Number of Press  
1 2 3 4 5  
Place the  
Originals  
Press 2  
in 1 key  
(Reduction/  
Enlargement  
Only)  
Copies  
START  
CThe ADF/i-ADF is required for 2 in 1 copy.  
CPress the RESET key to cancel all job settings.  
NOTE  
CNumbers in parenthesis ( ) represent that, an additional step is required to  
activate the feature.  
The Orientation and Layout can be set in the Copier Settings function mode.  
(See page 27)  
16  
Creative Features  
2 PAGE COPY  
I 2 PAGE Copy  
Copying two facing pages on a ledger size original on two separate Letter size sheets.  
I Procedure  
1 2 3 4 5  
ORIGINAL SIZE  
(Letter or Ledger  
size Only)  
Number of Press  
Place the Press the 2  
Originals PAGE COPY  
key  
Copies  
START  
Platen  
Ledger size original  
Book Mark  
Center book  
by length  
and width  
according  
to center  
marks.  
Letter  
CTo reset all job settings, press the RESET key.  
NOTE  
17  
Creative Features  
BOOK/EDGE/MARGIN  
I BOOK Key  
Eliminates dark inner binding shadows when copying from a book.  
I EDGE Key  
Creates a blank edge.  
I MARGIN Key  
Shifts the image to the right or left.  
I Procedure  
3
Press Cursor (G or F) keys to adjust  
the void width while the button is  
blinking. (approx. 5 sec.)  
CVoid/Margin width: 5-99 mm  
1 2  
4 5  
Place the  
Original  
Number  
of Copies START  
Press  
Press BOOK, EDGE  
or MARGIN key  
Book  
Initial Book Margin setting (Factory setting): 20 mm  
BOOK MARGIN  
CENTER VOID = 20mm∨∧  
Edge  
Initial Equal Rate setting (Factory setting): 5 mm  
Initial Left Margin setting (Factory setting): 10 mm  
EQUAL RATE  
VOID MARGIN = 5mm  
Margin**  
LEFT MARGIN  
10mm∨∧  
Initial setting (Factory setting) can be changed in the Copier Settings function mode.  
(See page 30)  
NOTE  
If a part of the copied image is missing when using the Margin mode, change the  
Frame Reduction setting to ON.  
(See page 30)  
∗∗  
CPress the RESET key to cancel all job settings.  
18  
Creative Features  
2-Sided/1-Sided Copy (For DP-2010E)  
I Key Operation  
Press 2-Sided/1-Sided Copy key (circulation) to select a 2-Sided/1-Sided Copy function.  
2-Sided/1-Sided Copy key  
From 1-Sided originals to 2-Sided  
copies.  
(See page 20)  
(See page 20)  
(See page 21)  
(See page 20)  
1 \ 2  
2 \ 2  
From 2-Sided originals to 2-Sided  
copies.  
From book originals to 2-Sided copies.  
Book \ 2  
2 \ 1  
From 2-Sided originals to 1-Sided  
copies.  
C2-Sided originals may be handled either manually or automatically using the  
i-ADF (DA-AR201).  
NOTE  
C2-Sided/1-Sided Copy function is only available for DP-2010E.  
19  
Creative Features  
1 \ 2 / 2 \1 / 2 \ 2 Copy (For DP-2010E)  
I 1 \ 2 Copy  
I 2 \ 1 Copy  
I 2 \ 2 Copy  
From 1-Sided originals to  
From 2-Sided originals to  
From 2-Sided originals to  
2-Sided copies.  
1-Sided copies.  
2-Sided copies.  
(From Copier Platen & i-ADF/  
ADF)  
(Using i-ADF)  
(Using i-ADF)  
Long Edge (Binding)*  
Long Edge (Binding)*  
Long Edge (Binding)  
Short Edge (Binding)  
Short Edge (Binding)*  
Short Edge (Binding)*  
I Procedure  
i-ADF  
Face-Up  
( )  
1 2 3 4 5  
Place the  
Originals  
COPY SIZE  
(Reduction/  
Number of Press  
Copies START  
Press 2-Sided/  
1-Sided Copy key  
(circulation) to  
select 1 \ 2, 2 \ 2  
or 2 \ 1  
Enlargement Only)  
Press the I or H key to select  
the binding location.  
BINDING:LONG EDGE  
PRESS < > TO SELECT  
(When selecting 1 \ 2 Copy or 2 \ 1 Copy)  
CTo reset each selection, press the RESET key.  
NOTE  
The initial setting of binding location for 1 \ 2 Copy and 2 \ 1 Copy (Long edge or  
Short edge) can be set in function mode. (See page 30)  
C1 \ 2, 2 \ 2, 2 \ 1 Copy function is only available for DP-2010E.  
20  
Creative Features  
Book \ 2 Copy (For DP-2010E)  
I Book \ 2 Copy  
From book originals to 2-Sided copies.  
Ledger size originals only.  
Facing (Book Format)*  
Flipping (Book Format)*  
( )  
1 2 3 4 5  
COPY SIZE  
Press 2-Sided/  
1-Sided Copy key  
(circulation) to select  
Book \ 2  
Number of  
Copies  
Press  
START  
Place the  
Original on  
the Platen  
(Reduction/  
Enlargement Only*)  
Platen  
Ledger size original  
Ledger  
Book Mark  
Center book by  
length and width  
according to  
center marks.  
Letter  
CTo reset each selection, press the RESET key.  
CLedger and Legal copy sizes cannot be selected.  
NOTE  
The book format and page order can be set in function mode. (See page 30)  
CBook \ 2 Copy function is only available for DP-2010E.  
21  
Creative Features  
Job Memory  
I Two Copy Jobs Can Be Programmed in Memory (M1, M2) for recall at a  
later time.  
To Store a Job in Memory  
#Set up the copy job to be stored in memory,  
by first selecting each function you wish the  
copier to perform.  
$Press the MEMORY IN (F2) key.  
JOB MEMORY  
PRESS M1,M2 TO STORE.  
%Press the M1 (F3) or M2 (F4) key.  
To Recall a Job Stored in Memory  
&Place the Original  
(Press the M1 (F3) or M2 (F4) key.  
RECALL JOB MEMORY  
LOADING...  
The stored contents will be displayed.  
)Press START  
CStored job(s) will not be deleted even if the power switch is turned Off.  
CWhen storing a new job into programmed memory, the previously stored job will be  
NOTE  
overwritten.  
22  
Creative Features  
Sort Copy  
I Sort Copy  
The sort copy has 2 available electronic sorting functions as follows:  
Note: Before using the sort copy, select the desired sorting mode by setting its function first  
(See page 29).  
Sort  
Sort-Rotate  
Multiple copies  
sorted  
automatically.  
Multiple copies sorted  
automatically and  
Stacked in alternate  
direction.  
1
1
1
1
1
(Up to Letter size)  
Platen Glass  
ADF/i-ADF  
( )  
1 2 3 4 5  
COPY SIZE  
(Reduction/  
Enlargement  
Only)  
ADF/i-ADF: Place the  
Originals  
Platen: Place the  
First Original  
Select the  
SORT Mode  
Number of Press  
Copies START  
From Platen Glass only:  
ANOTHER ORIGINAL?  
1:YES 2:NO  
Place next Original  
Press START  
7 8  
6
Press 1key.  
Repeat steps 6 and 7  
until all originals are  
ANOTHER ORIGINAL?  
1:YES 2:NO  
9 10  
scanned and stored  
into the copiers memory.  
Press 2key.  
CWhen the memory becomes full during original scanning, the message  
OUT OF MEMORY” “CONTINUE? 1:YES 2: NOwill be displayed in the  
message display. If this occurs, follow the instructions in the message  
display.  
NOTE  
For additional memory consult your authorized servicing dealer.  
CTo reset all job settings, press the RESET key.  
23  
Other Features  
Energy Saver/Interrupt Mode  
INTERRUPT (F1) Key ENERGY-SAVER Key  
I These modes can save power while the copier is not  
ENERGY SAVER  
in use.  
Energy Saver Mode  
#To enter this mode  
Press the ENERGY-SAVER key or the copier will  
automatically enter the ENERGY-SAVER Mode after  
15 minutes* from the last copy.The indicator will flash.  
$To cancel this mode and make copies  
Press the ENERGY-SAVER key again.  
Sleep Mode  
#Automatically enters the Sleep Mode after 30  
minutes from the last copy. The copier power will  
drop and the indicator will light.  
$To make copies, press the ENERGY-SAVER key.  
Interrupt Mode  
CThis mode can interrupt other copy jobs while  
making copies.  
INTERRUPT  
#Press the INTERRUPT (F1) key, the indicator will  
light.  
$Make another copy job using the platen glass.  
%Press the INTERRUPT (F1) key again to continue  
the original job.  
Note: The ADF can not be used with interrupt.  
(Use only the Platen)  
Energy saver time (15 minutes) and Sleep time (30 minutes) can be changed by the  
key operator. (See page 31)  
NOTE  
Modes  
Power Consumption  
Approximately 92 Wh  
Approximately 40 Wh  
Approximately 1.5 Wh  
Warm UpTime  
N/A  
Normal Operation  
Energy Saver Mode  
Sleep Mode  
30 sec. recovery  
30 sec. recovery  
24  
Other Features  
Skyshot Mode  
I Skyshot allows copying a manuscript without generating dark borders  
even if the platen cover or ADF/i-ADF is opened.  
Skyshot mode eliminates dark borders around the originals, and is especially convenient for  
copying small-sized originals like bank checks or documents with unusual shapes (round, oval,  
etc.).These documents can be reproduced without generating any unnecessary black areas  
simply by making a copy with the cover open.  
Two types of Skyshot modes can be selected;  
Digital Skyshot Mode :The scanning area (size) is not pre-determined.  
Manual Skyshot Mode:The scanning area (size) is pre-registered into memory (M1 and M2) in  
advance. (See page 30)  
I Digital Skyshot Mode  
1
3
2
Place the Original on  
the platen (Opening the  
Platen Cover/ADF)  
Press  
START Key  
Number of  
Copies  
Note:The default setting of Digital Skyshot Mode is NORMAL. In this setting, the unit scans once.  
If there are black areas around the borders in the copies, set the Digital Skyshot Mode to  
QUALITYto soften the dark borders. In this setting, the unit scans twice.  
#Press the FUNCTION key.  
$Press the 2 key to select COPIER SETTINGS.  
FUNCTION MODE (1-2)  
ENTER NO. OR ∨ ∧  
%Press the SET key.  
2:COPIER SETTINGS  
PRESS SET TO SELECT  
&Press 6 and SET key to select DIGITAL  
COPIER PARAM.(00-14)  
SKYSHOT.  
ENTER NO. OR ∨ ∧  
(
Press 1-3 key to select the Digital Skyshot Mode.  
1: OFF NONE  
06 DIGITAL SKYSHOT  
2:NORMAL  
2: NORMAL Default setting (usually select this  
mode).  
3: QUALITY For better definition, select the  
Quality mode.  
)Press the SET key.  
*Press the RESET key.  
CAn incorrect exposure may occur when there is a black line at the edge of  
the original or an image which the copier interprets as a black pattern in the  
Skyshot mode.  
NOTE  
CAn incorrect position detection of the original may occur when a strong light  
shines onto the glass during Skyshot mode.  
25  
Other Features  
Skyshot Mode  
I Manual Skyshot Mode  
When using this function, the custom size should be registered into memory (M1, M2) in  
advance. (See page 32)  
Platen  
Upper-  
left  
corner  
1 2 3 4  
Place the  
Original  
Select the Custom  
Size (M1 or M2)  
Number of Press  
Copies  
START  
#Press the FUNCTION key.  
$Press the 2 key to select COPIER SETTINGS.  
FUNCTION MODE (1-2)  
ENTER NO. OR ∨ ∧  
2
%Press the SET key.  
2:COPIER SETTINGS  
PRESS SET TO SELECT  
&Press 7 and SET key to select MANUAL SKYSHOT.  
COPIER PARAM.(00-14)  
ENTER NO. OR ∨ ∧  
(
Press 2 or 3 key to select the Custom Size.  
07 MANUAL SKYSHOT  
2:M1 ON  
1: OFF  
NONE  
2: M1 ON  
3: M2 ON  
M1 size is ON*  
M2 size is ON*  
4: M1, M2 ON Both sizes are ON  
)Press the SET key.  
*Press the RESET key.  
The default size for M1 is: 70(X) × 160(Y) mm, and M2 is: 95(X) × 220(Y) mm  
NOTE  
CWhen changing the M1 or M2 size, consult with the key operator.  
CWhen using the Manual Skyshot mode, M1 and M2 are turned ON and other  
job memory cannot be used.  
CPress the RESET key to cancel all job settings.  
26  
Combined Function Table  
2-ORIGINAL  
H COPY  
Other  
Functions  
Margin  
SORT  
Remarks  
Next  
Selections  
First  
Selections  
Zoom Copy  
A
O O O O O O O  
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
O
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
O
O
O
O
O
O
O
O
2 in 1 Copy  
2 Page Copy  
1 \ 2  
O
O
O
O
O
O
O
A A O A A A  
A A A A A A  
O A A A A A  
O A A A A A  
O A A A A A  
O A A A A A  
O
O
O
O
O
O
O
O
O
O
O
O
O
2 \ 2  
Book \ 2  
2 \ 1  
Book  
O O O O O O A  
O O O O O O O  
O O O O O O O  
O O O O O O O  
O O O O O O O  
O O O O O O O  
Edge  
O
O
O
O
O
A
O
A
O
O
A
O
O
A
O
O
A
A
A
A
A
A
A
A
A
A
A
O
O
O
O
O
Margin  
Non-Sort  
Sort  
O
O
O
O
O
O
O
A
A
A
Sort-Rotate  
A
A
A
Manual Skyshot  
Interrupt  
O
O
✕ ✕ A A A A  
O
O
O
O
O
O
A
A
O ✕ ✕ ✕ ✕  
O: Possible Combined Functions.  
: Unavailable Combined Functions.  
A : Next Selection is Carried Out.  
: Indicates that SORT mode cannot be used. Non-sort operation is carried out.  
27  
Function  
I Using Function Modes to Change the Initial Copy Modes  
Options  
General  
Functions  
Copier  
Settings  
Printer  
Settings  
LAN Settings  
Input Identification Code  
General  
Functions for  
Key Operator  
Copier  
Settings for  
Key Operator  
LAN Settings  
for Key  
Operator  
Printer  
Settings for  
Key Operator  
FUNCTION Key  
I Procedure  
RESET Key  
COPY SIZE PAPER  
Key TRAY Key  
#Press the FUNCTION Key  
FUNCTION MODE (1-2)  
ENTER NO. OR ∨ ∧  
$Press 1 (GENERAL FUNCTIONS) or 2  
(COPIER SETTINGS) key.You may also use  
the (G or F) keys.  
%Press the SET key.  
&Press the Keypad to select function modes  
or use the (G or F) keys.  
(Follow the on screen instructions.  
)After setting, press the SET key to set up the  
function.  
I Checking the CopiersTotal Counter  
To display the copiers Total Counter, press the COPY SIZE and PAPERTRAY keys  
simultaneously.  
CPlease refer to each options operating instructions for function settings.  
NOTE  
28  
Function  
General Functions  
Initial  
Setting  
No.  
Modes  
Function  
Selects the sort mode.  
00  
SORT MODE DEFAULT  
NON-SORT  
OFF  
CNON-SORT, SORT  
05  
06  
SORT MEMORY USAGE  
DEPT. COUNTER  
Displays the amount of sort memory used on  
the panel.  
COFF, DISPLAY  
Copy usage and copy limit of the selected  
department and total copy usage will appear  
on the screen.  
Consult  
your  
service  
technician.  
08  
09  
SORT-ROTATE DEFAULT  
KEY OPERATOR MODE  
Select Sort-Rotate mode.  
COFF, ON  
OFF  
Input the key operator ID code.  
29  
Function  
Copier Settings  
Initial  
Setting  
No.  
Modes  
Function  
00  
MARGIN DEFAULT  
Selects the margin position and shift value.  
CPOSITION (Left, Right, Top, Bottom)  
CVALUE (5 - 99 mm)  
LEFT  
10 mm  
01  
EDGE DEFAULT  
Selects the edge mode (Equal Rate = set the EQUAL RATE  
same value for X & Y or Individual = set the  
value for X & Y individually) and width.  
CEQUAL RATE (X &Y ), INDIVIDUAL  
C5 - 99 mm  
5 mm  
02  
03  
04  
05  
06  
07  
BOOK MARGIN DEF.  
FRAME MARGIN  
Selects the book Center Void margin width.  
C5- 99 mm  
20 mm  
INVALID  
OFF  
Select the reduction ratio in margin mode.  
CINVALID, VALID  
2-SIDED MODE DEF.  
2 in 1 WITH FRAME  
DIGITAL SKYSHOT  
MANUAL SKYSHOT  
Function sets the duplex priority mode.  
COFF, 1 \ 2, 2 \ 2, Book \ 2 (For DP-2010E)  
Selects whether or not to disable edge deletion. INVALID  
CINVALID, VALID  
Enables or disables the use of skyshot mode.  
COFF, NORMAL, QUALITY  
NORMAL  
OFF  
Enables or disables the use of Manual  
Skyshot.  
COFF; M1 ON; M2 ON; M1, M2 ON  
08  
AUTO EXPOSURE  
Automatically adjusts the copy density for text  
and photographic originals.  
VALID  
CINVALID, VALID  
09  
10  
11  
1 \ 2 BINDING DEF.  
2 \ 1 BINDING DEF.  
BOOK \ 2 DEFAULT  
Selects the binding location for 1 \ 2 Copy.  
LONG EDGE  
LONG EDGE  
C
LONG EDGE, SHORT EDGE (For DP-2010E)  
Selects the binding location for 2 \ 1 Copy.  
LONG EDGE, SHORT EDGE (For DP-2010E)  
C
Selects the page order and book format for  
Book \ 2 Copy.  
FLIPPING  
L \ R  
1. BOOK FORMAT (1: FACING, 2: FLIPPING)  
2. PAGE ORDER (1: L \ R, 2: R \ L) (For DP-2010E)  
12  
2 in 1 DEFAULT  
Selects the orientation and layout for 2 in 1 Copy. PORTRAIT  
CORIENTATION (Portrait, LANDSCAPE)  
L \ R  
CLAYOUT (L \ R, R \ L)  
13  
14  
2 PAGE MODE DEF.  
Selects the 2 page mode.  
CL \ R, R \ L  
L \ R  
KEY OPERATOR MODE  
Input key operator ID code.  
CCertain Functions or Parameters are available for selection only when their  
NOTE  
respective option is installed.  
30  
Function  
General Functions for Key Operator  
Initial  
Setting  
1 min.  
No.  
Modes  
Function  
Selects the Control Panel reset time.  
COFF, 30 sec, 1 min., 2 min., 3 min., 4 min.  
01  
AUTO RESET TIME  
Sets the Energy Saver mode and time.  
CINVALID, ENERGY-SAVER, SLEEP  
Energy save mode timer : 1-120 minutes  
SLEEP  
02  
ENERGY SAVER MODE  
Sleep mode timer  
: 1-120 minutes  
Selects the message language of the display.  
04  
05  
LANGUAGE DEFAULT  
SPECIAL TRAY 1  
A-ENGLISH  
CA-ENGLISH, C-FRENCH, SPANISH  
Sets the paper tray for special paper (ex: colored). NONE  
CNONE, TRAY 1, TRAY 2, BYPASS  
06  
SPECIAL TRAY 2  
KEY/TOUCH BEEP  
BYPASS SET BEEP  
Sets the paper tray for special paper.  
CNONE, TRAY 1, TRAY 2, BYPASS  
NONE  
SOFT  
Sets the panel touch sound.  
COFF, SOFT, LOUD  
09  
10  
Sets the sound when put paper(s) on bypass  
INVALID  
tray.  
C1: INVALID 2: VALID  
11  
14  
ORIG. SET BEEP ADF  
DEPT. COUNTER MODE  
Sets the sound when put paper(s) on ADF.  
C1: INVALID 2: VALID  
VALID  
Monitors copy usage of each department.  
(1) TOTAL COUNTER  
Consult  
your  
service  
technician.  
(2) DEPT. COUNTER  
(3) DEPT. COUNTER LIST  
15  
16  
22  
TOTAL COUNT  
Total print out volume from the main unit.  
PC PRINT COUNT  
TCP/IP ADDRESS  
Total print out volume from the PC.  
Contact  
your  
Network  
Adminstrator.  
Sets the IP Address assigned to your machine.  
C3 digit × 4 (Use the MEMORY IN key to  
enter the .between each set of 3-digit  
numbers)  
Contact  
your  
Network  
Adminstrator.  
23  
24  
25  
TCP/IP SUBNET MSK  
TCP/IP G/W ADDR.  
COPY SETTING LIST  
Sets the Subnet Mask.  
C3 digit × 4 (Use the MEMORY IN key to  
enter the .between each set of 3-digit  
numbers)  
Contact  
your  
Network  
Adminstrator.  
Sets the Subnet Mask.  
C3 digit × 4 (Use the MEMORY IN key to  
enter the .between each set of 3-digit  
numbers)  
Prints list containing Current Setting and  
Standard Setting.  
CIt is necessary to input the Key Operator ID code before changing items on  
this page.  
NOTE  
CThe Special Tray 1 and 2 are not auto-selectable in the switching mode.  
Not available for plain copier, but will be available when installing options  
with advanced functions. (See page 57)  
31  
Function  
Copier Settings for Key Operator  
Initial  
Setting  
No.  
Modes  
Function  
Selects original setting  
01  
ORIGINAL (HOME)  
T/P  
CTEXT, T/P (Text/Photo), PHOTO  
(Text/Photo)  
02  
03  
04  
10  
12  
TEXT CONTRAST  
T/P CONTRAST  
PHOTO CONTRAST  
MAX. COPY SETTING  
M1, SIZE  
Selects contrast for Text mode  
C1 ~ 5  
3
Selects contrast for Text/Photo mode  
C1 ~ 5  
3
Selects contrast for Photo mode  
C1 ~ 5  
3
Determines whether to limit number of copies  
C1 ~ 999  
999  
70 × 160 mm  
Input a size in memory 1 for frequent usage  
size.  
(X) (Y)  
CX: 5~432/Y: 5~297 mm  
(See page 22)  
95 × 220 mm  
Input a size in memory 2 for frequent usage  
size.  
CX: 5~432/Y: 5~297 mm  
(See page 22)  
13  
16  
M2, SIZE  
(X) (Y)  
MEM. FULL ACTION  
Selects the memory full action  
Print  
CPRINT, CANCEL  
CIt is necessary to input the Key Operator ID code before changing items on  
NOTE  
this page.  
32  
Function  
Function Setting  
I Changing the Auto Exposure Setting  
You can select whether the copying density is adjusted automatically for text and photographic  
originals.  
Press the FUNCTION key.  
FUNCTION Key  
1
Proceed as Follows:  
2
#Press the 2 key to select COPIER SETTINGS.  
FUNCTION MODE (1-2)  
ENTER NO. OR ∨ ∧  
$Press the SET key.  
2:COPIER SETTINGS  
PRESS SET TO SELECT  
%Press 8 and SET key to select AUTO  
COPIER PARAM.(00-14)  
EXPOSURE MODE.  
ENTER NO. OR ∨ ∧  
&Press 1 or 2 key to select whether Auto  
Exposure is to be carried out or not.  
08 AUTO EXPOSURE  
2:VALID  
(Press the SET key to set up the AUTO  
EXPOSURE MODE.  
)Press the RESET key to exit the Function mode.  
33  
Function  
Function Setting for Key Operator  
I Changing the Paper Size  
The Paper Trays are designed to accommodate Invoice, Letter, Letter R, Legal and Ledger size  
paper. To change the paper size, perform the steps shown below.  
Press the FUNCTION key.  
FUNCTION Key  
1
Proceed as Follows:  
2
FUNCTION MODE (1-2)  
ENTER NO. OR ∨ ∧  
#Press the 1 key to select GENERAL  
(Press 00 and 1 or 2 key to select  
FUNCTIONS.  
the PAPER SIZE.  
1:GENERAL FUNCTIONS  
PRESS SET TO SELECT  
00 PAPER SIZE  
1:TRAY-1[LTR  
B]  
$Press the SET key.  
)Press SET to select the paper tray and  
press (G or F) keys to set the paper  
size.  
GENERAL PARAM. (0-9)  
ENTER NO. OR ∨ ∧  
Paper size changes are as follows.  
Letter R  
Ledger  
Invoice R  
A3  
B4  
A4  
%Press 9 key.  
Letter  
Legal  
A4R  
B5  
09 KEY OPERATOR MODE  
ENTER PASSWORD=-I I  
FLS2 FLS1  
A5R  
B5R  
*Press the SET key to set up the PAPER  
&Input the Key Operator ID code (3 digit)  
SIZE.  
and the SET key.  
+Press the RESET key to exit the Function  
KEY OPR.MODE (00-25)  
mode.  
ENTER NO. OR ∨ ∧  
34  
Function  
Function Setting for Key Operator  
Changing the Paper Guide and Paper Size Indicator in the Paper Tray  
3
#Pull the Paper Tray out and remove  
paper.  
$Adjust the paper guide a to the  
required paper length.  
%Adjust the Paper Guide b to the  
required paper width.  
Pinch the stopper to move the Paper  
Guide b.  
Paper  
Guide a  
Stopper  
Paper  
Guide b  
&Change the Paper Size Indicator.  
Size  
Indicator  
(Close the Paper Tray.  
CIt is recommended that the paper guide b be fixed in place with screws.  
NOTE  
Consult an authorized servicing dealer for details on how to fasten with  
screws.  
35  
Function  
Function Setting for Key Operator  
I Department Counter  
The Key Operator can manage, limit copies, counters and code numbers for each department.  
(Maximum department counters: 50)  
Press the FUNCTION key.  
FUNCTION Key  
1
Proceed as Follows:  
2
FUNCTION MODE (1-2)  
ENTER NO. OR ∨ ∧  
#Press the 1 key to select GENERAL  
&Press the Key Operator ID code (3 digit)  
FUNCTIONS.  
and SET key.  
1:GENERAL FUNCTIONS  
PRESS SET TO SELECT  
KEY OPR.MODE (00-25)  
ENTER NO. OR ∨ ∧  
$Press the SET key.  
(Press 14 and the SET key to select  
DEPT. COUNTER MODE.  
GENERAL PARAM. (0-9)  
ENTER NO. OR ∨ ∧  
%Press 9 key.  
09 KEY OPERATOR MODE  
ENTER PASSWORD=-I I  
CTo reset the function mode, press the RESET key.  
NOTE  
C
Contact your authorized servicing dealer to enable the Department Counter  
feature.  
36  
Function  
Function Setting for Key Operator  
Select the Department Counter Mode.  
3
14 DEPT.COUNTER MODE  
1:TOTAL COUNTER  
Press 2 and the SET key.  
DEPT. CODE (01-50)  
ENTER NO. OR ∨ ∧  
Change the Department ID Code, limit the maximum number of copies  
and Department Counter number.  
4
#Press the Keypad and the SET key to input the  
ID CODE  
01:1234  
Department ID Code.  
01: 1234  
Department ID Code  
Department No.  
$Press the Keypad and the SET key to input the  
MAX COPIES  
01:123456  
maximun number of copies.  
01: 123456  
Maximun number of copies (6 digits)  
Department No.  
%Press the Keypad and the SET key (G or F keys) to  
DEPT.COUNTER  
01:123456  
select the Department No.  
01: 123456  
Counter (6 digits)  
Department No.  
&Press 0 and the SET key (Input 0) to clear the counter.  
CTo reset the function mode, press the RESET key.  
NOTE  
37  
38  
Accessories  
Components  
i-ADF (Inverting Automatic Document Feeder)  
(DA-AR201)  
ADF (Automatic Document Feeder)  
(DA-AS180)  
CFeeds original automatically  
CDuplexing  
CFeeds originals automatically.  
C2 in 1 Copy  
C2:1 Copy  
C2 in 1 Copy  
Image Memory  
(DA-SM08B/SM16B/SM64B/SM28B)  
C8/16/64/128 MB  
DP-1810P  
with Options  
CTo increase the memory capacity for  
electronic sorting and sort printing.  
DP-2010E  
with Options  
2nd/4th Paper Feed Module  
(DA-DS182)  
CTo increase the paper feed sources  
and capacity.  
Paper Feed Module × 1 (550 sheets)  
3rd Paper Feed Module  
(DA-DS183)  
CTo increase the paper feed sources  
and capacity.  
PCL6 Emulation Kit  
(DA-PC210)  
CPrinter Controller for PCL6*  
Paper Feed Module × 1 (550 sheets)  
10/100 Ethernet Interface/  
Internet Fax Kit  
(DA-NE200)  
CNetwork Interface Board  
PCL6 is a Page Description Language of the Hewlett-Packard Company.  
C
NOTE  
CThe table below shows the options which are required for various functions.  
Contact your authorized servicing dealer for details on combinations of options.  
Other  
2-ORIGINAL H  
Function  
Margin  
SORT  
COPY  
Functions  
Options  
ADF  
i-ADF  
2nd/3rd/4th Paper  
Feed Module  
:Required  
39  
Accessories  
Automatic Document Feeder  
I ADF (DA-AS180) / i-ADF (DA-AR201)  
1. Features  
#Automatic Original Feeding  
CThe ADF/i-ADF tray can hold up to 50 Letter size originals of 20 lb (80 g/m2) paper (up to 30  
Legal or Ledger size originals). It can accommodate from Invoice to Ledger size originals.  
CAutomatic original size detection.  
$2 in 1 Copy  
CTo make a 1-Sided copy (full size or reduction), from two 1-Sided originals side-by-side.  
%Duplex Copying (DA-AR201)  
CThe i-ADF allows you to copy 2-sided originals either manually or automatically.  
2. Components  
CSet the originals up to the upper limit arrow.  
ADF (DA-AS180)  
i-ADF (DA-AR201)  
ADFTray  
i-ADFTray  
Original Guides  
Original Guides  
Adjust to the originals width  
Adjust to the originals width  
40  
Accessories  
3. Operation  
I Operation Procedure  
ADF/i-ADF  
Face-Up  
( )  
1 2 3 4  
For Duplex Copy  
(If required)  
Number of  
Copies  
Press  
START  
Place the  
Original  
Inappropriate Originals  
CPaste-ups  
CPaper with a smooth surface such as glossy CPressure sensitive or carbon backed papers  
and coated papers  
CTransparencies  
CPaper with excessive curl  
CStapled originals  
COriginals with a lead edge that is “creased”,  
“folded”, “punched” or “glued”  
CFreshly printed copies from a laser printer  
CTo copy these kinds of originals, use the Platen Glass instead.  
NOTE  
41  
Problem Solving  
Adding Paper (J)  
I 550-Sheet Paper Tray  
Pull the Paper Tray out.  
1
Place the paper with the copying  
surface facing upward.  
Special papers, like glossy paper, mailing  
labels and transparencies cannot be used  
in the paper tray.  
2
3
4
Use the Sheet Bypass for special paper.  
Make sure paper is not loaded  
above the overfill indicator located  
in the Paper Tray.  
Firmly push the Paper Tray back  
into the copier.  
CDo not use paper with folds or wrinkles.  
ATTENTION  
Refer to page 35 for details on adjusting the paper tray size.  
CUnused paper should always be placed into a bag and the opening should be sealed  
for storage.  
If the paper is left exposed, problems such as paper curl, paper jams, wrinkles or  
loss of copied image quality may occur.  
42  
Problem Solving/U13  
Adding the Toner and Replacing Toner Waste Container (?)  
Open the Front Cover.  
1
Remove the Toner Waste Container by  
slowly pulling it towards the left as  
illustrated.  
2
Seal the container with the enclosed  
cap and dispose of it properly.  
3
Cap  
# Turn the empty Toner Bottle  
1
counter-clockwise until it stops. The  
Arrow mark (Unlocked symbol )  
visible on the end of the Toner  
Bottle is aligned with the Arrow  
mark on the machine.  
4
2
Note: To prevent toner spill, ensure  
that the key is facing upwards  
before removing the toner bottle.  
$ Pull the empty Toner Bottle out.  
Note: If the bottle will not pull out from  
the machine, turn the bottle  
J
?
slightly in either direction to  
release the key and try it again.  
Continued on the next page...  
CFor optimum copy quality use the recommended Panasonic toner. Store toner in a cool  
dark place. Do not unseal toner before use. Use it as fast as possible after unsealing.  
CWhen U13 is displayed the Add Toner Warning Indicator will begin to flash.This message  
is to prompt you that the toner bottle is nearly empty (approx. 300-sheets can be printed).  
This message will continue to be displayed until the bottle is replaced. When the count-  
down counter reaches 0, the copier will stop operating. To clear the message and enable  
the copier to operate, replace the empty toner bottle with a new one.  
ATTENTION  
43  
Problem Solving  
Adding the Toner and Replacing Toner Waste Container (?)  
# Shake the new Toner Bottle four  
or five times to loosen the  
contents.  
2
5
1
$ Remove the cap from the Toner  
Bottle.  
# Align the Key of the bottle, also  
represented by the Arrow mark  
(Unlocked symbol ) visible on  
the end of the Toner Bottle with  
the Arrow mark on the machine.  
6
1
Note:To prevent toner spill,  
ensure that the key is facing  
upwards before installing the  
2
2-1  
2-3  
bottle.  
$ Insert the bottle as far as it will  
go, then turn it clockwise (160°,  
approx. 1/2 turn) until it locks  
(Locked symbol ).  
2-2  
Incorrect  
Correct  
Note: If the bottle is not inserted  
all the way into the machine  
as illustrated, turn the bottle  
slightly in either direction to  
engage the key and try it  
again.  
Install a new Toner Waste  
Container.  
7
Close the Front Cover.  
8
CDo not reuse the toner from the Toner Waste Container.  
ATTENTION  
44  
Problem Solving  
Removing a Misfed Paper  
I Paper Misfeed Indicators and Locations  
When a paper misfeed occurs, the misfeed indicator and the misfeed  
location(s) will be displayed on the panel display.  
Misfeed Indicator  
I
For DP-2010E  
For DP-1810P  
Paper Misfeed Locations  
A: ADF (see page 51), i-ADF(see page 50)  
(J70, J71)  
B: Copier (Paper Exit, Paper Entry/Transport,  
ADU) areas (see page 46-48) (J51 - J59,  
J80)  
C: Paper Feed Module (see page 49)  
(J00 - J50)  
I
CMake sure that the misfeed indicator goes off after removing the misfed  
paper.  
NOTE  
CThe misfeed indicator will not go off if the paper is still jammed in the copier.  
Check again and remove all misfed paper.  
45  
Problem Solving  
Removing a Misfed Paper  
I Paper Exit Area  
CMake sure that the misfeed indicator  
goes off after removing all misfed  
paper.  
For DP-1810P  
For DP-2010E  
Remove the misfed paper.  
1
CMake sure that the misfeed indicator goes off after removing all misfed paper.  
ATTENTION  
46  
Problem Solving  
I Paper Entry/Transport Area  
CMake sure that the misfeed indicator  
goes off after removing all misfed  
paper.  
For DP-1810P  
For DP-2010E  
Open the Right Cover.  
1
Remove the misfed paper.  
2
3
4
If copy paper is fed far into the copier:  
#Turn the right paper clearing knob.  
$Remove the misfed paper.  
#Open the Heat Roller Cover.  
$Remove the misfed paper.  
%Close the Right Cover.  
Caution:This fuser area may be  
hot.  
Caution  
heated  
surface  
I
CMake sure that the misfeed indicator goes off after removing all misfed paper.  
ATTENTION  
47  
Problem Solving  
Removing a Misfed Paper  
I
ADU Area (For DP-2010E only)  
CMake sure that the misfeed indicator  
goes off after removing all misfed  
paper.  
Open the Right Cover.  
1
Remove the misfed paper.  
2
3
If copy paper is fed far into the copier;  
#Turn the right paper clearing knob.  
$Remove the misfed paper.  
Close the Right Cover.  
4
48  
Problem Solving  
I Paper Feed Module  
CMake sure that the misfeed indicator  
goes off after removing all misfed  
paper.  
For DP-1810P  
For DP-2010E  
#Pull the paper tray out.  
$Remove the misfed paper.  
%Return the Paper Tray to the original  
position.  
1
#Open the Feed Cover.  
$Remove the misfed paper.  
%Close the Feed Cover.  
2
I
CMake sure that the misfeed indicator goes off after removing all misfed  
ATTENTION  
paper.  
49  
Problem Solving  
Removing a Misfed Paper  
I i-ADF (For DP-2010E only)  
CMake sure that the misfeed indicator  
goes off after removing all misfed  
paper.  
#Open the Entry Cover.  
$Remove the misfed paper.  
%Close the Entry Cover.  
1
2
3
4
#Open the ADF Cover.  
$Remove the misfed paper.  
%Close the ADF Cover.  
&Open and close the Entry Cover to  
reset the error.  
#Lift up the ADF Input Tray.  
$Remove the misfed paper.  
%Close the ADF Input Tray.  
&Open and close the Entry Cover to  
reset the error.  
#Lift up the ADF Input Tray.  
$Open the ADF exit cover.  
%Remove the misfed paper.  
&Close the ADF exit cover.  
(Close the ADF Input Tray.  
CPush the tab on the center of the Entry Cover to close it.  
CTo prevent original(s) damage, please make sure to open the ADF Cover before  
ATTENTION  
removing misfed original(s).  
50  
Problem Solving  
I ADF  
CMake sure that the misfeed indicator  
goes off after removing all misfed  
paper.  
#Open the Entry Cover.  
$Remove the misfed paper.  
%Close the Entry Cover.  
1
2
#Open the ADF Cover.  
Note: To prevent damaging the originals,  
open the ADF Cover before  
removing the misfed original(s).  
$Remove the misfed paper.  
%Close the ADF Cover.  
&Close the ADF.  
I
CTo prevent original(s) damage, please make sure to open the ADF Cover  
ATTENTION  
before removing misfed original(s).  
51  
Troubleshooting  
Before Calling Service  
Check  
Action  
Unit Does Not Operate  
Check if the Power Switch is turned On and  
that the power cord is connected into the  
outlet.  
Does the display light?  
(No)  
(Yes)  
(Yes)  
(Yes)  
(Yes)  
(Yes)  
(Yes)  
Does the Energy Saver key flash (or light)  
and displays are turned OFF? (See page  
Press Energy Saver key on the Control  
Panel.  
24)  
(No)  
Does any of the U## codes and messages  
appear on the display?  
(U01, U07, U13, U14, U20 and U21)  
(See page 54)  
Perform actions in accordance with each  
message.  
(No)  
Does the add paper indicator and message  
appear on the display? (J)  
Add paper. (See page 42)  
(No)  
Does the paper misfeed indicator and  
message appear on the display? (I)  
Remove the misfed paper. (See page 45)  
(No)  
Does E#-## indicator and message appear  
on the display?  
Turn the copier Off, then On. If the Error  
Code does not clear, call for service.  
When the Add Toner Warning Indicator begins to flash or is lit, replace the toner bottle with a new  
one. After this warning is activated, machine operation will begin with the Toner Charging Mode  
(approximately 3 minutes to complete) each time the power switch is turned Off then On or if the  
Front/Right Cover is opened and then closed.  
Note: When the warning indicator starts flashing, a 300-sheet count-down counter is activated,  
and upon reaching 0 the machine will stop operating. The 300-sheet counter is based on  
6 % fill, depending on the density some pages may print Blank.  
Machine operation and displays are as follows:  
1. When turning the power switch to On or opening and then closing the Front/Right Cover, the  
machine starts to warm-up and the LCD displays:  
PLEASE WAIT...  
52  
Troubleshooting  
2. The Toner Charging Mode starts and the LCD displays:  
CHARGING TONER  
AddToner Warning Indicator:  
CFlashing = Toner Bottle is nearly empty  
CLit  
= Toner Bottle is empty  
3. This message is displayed for approximately 200 seconds.  
CHARGING TONER  
❚ ❚ ❚ ❚ ❚  
Each is approximately 10 sec.  
4. This massage will continue to be displayed until the warm-up cycle is completed, and if the toner  
bottle was replaced. Upon completion, the Add Toner Warning Indicator automatically turns Off.  
Check  
Action  
Light Copies  
Press the Darker key until the indicator  
LED is set to Darker. (See page 12)  
Does the exposure indicator say Lighter?  
(Yes)  
(Yes)  
(No)  
Does the add toner indicator and message  
appear on the display? (?)  
Add Toner. (See page 43)  
Marked Copies  
Is the copier Platen Glass or Platen Cover  
dirty?  
Clean the Glass or Platen Cover.  
(See page 54)  
(Yes)  
53  
Troubleshooting  
User Error Codes (U Code)  
The self-diagnostic functions detect troubles in the important components of the copier.  
When any trouble occurs, the copier stops.  
Code  
U01  
Display Message  
CLOSE FRONT/RT COVER  
CLOSE FEED COVER  
Check Points  
Front Cover is open.  
U07  
Feed Cover is open.  
TONER IS RUNNING LOW  
NO WASTE TONER BOX  
1.Toner Cartridge is incorrectly installed.  
2. Low Toner or No Toner Waste Container.  
U13  
1.Toner Waste Container is incorrectly  
installed.  
2.Toner Waste Container is full of toner.  
U14  
WASTE TONER BOX IS FULL  
U20  
U21  
CLOSE ADF COVER  
ADF Cover is open.  
While the copier is initializing, the ADF  
Cover was opened. (Optional ADF installed)  
CLOSE PLATEN COVER  
I If the measures outlined above do not solve the problem, call your Service provider.  
Copier Care  
I As a rule, clean weekly.  
Platen/Platen Cover  
Platen  
Cover  
#Wipe marks off with a cloth and a neutral  
detergent.  
$Wipe again with a dry cloth.  
Platen  
(Glass)  
54  
Specifications  
I DP-1810P/2010E (Copier)  
Type  
Desktop  
PlatenType  
Fixed  
Acceptable Originals  
Copying Method  
Fixing Method  
Imaging Method  
Resolution  
Sheets, Books (max. size = Ledger)  
Laser Electrophotography  
Heat Roller Fixing  
Dry-Type Single component imaging  
Max. 600 dpi  
Maximum Copy Size  
Minimum Copy Size  
Void Area  
Ledger  
Invoice, via paper tray  
Max. 0.2 in (5 mm)  
Warm UpTime  
First CopyTime  
Multi-Copy Speed  
Approx. 30 seconds (68°F/20°C)  
Approx. 6.5 seconds (Letter , from 1st tray)  
DP-1810P : 18 cpm (Letter size)  
DP-2010E : 20 cpm (Letter size)  
Enlargement Ratios  
Reduction Ratios  
Paper Feed  
Preset: 121 %, 129 %, 155 %, 200 %  
Variable: from 101 to 200 % in 1 % increments  
Preset: 79 %, 77 %, 65 %, 61 %, 50 %  
Variable: from 99 to 50 % in 1 % increments  
Paper Tray (550 sheets × 1) + Sheet Bypass (50 sheets)  
2nd Paper Feed Module (550 sheets - option)  
3rd Paper Feed Module (550 sheets - option)  
4th Paper Feed Module (550 sheets - option)  
Paper Tray: 16 - 24 lb (60 - 90 g/m2)  
PaperWeight  
[Sheet Bypass: 15 - 34 lb (56 - 128 g/m2)]  
Quantity Selector  
Max. 999 sheets (Output Tray capacity is 250 sheets)  
AC 120 V, 50/60 Hz, 9 A  
Electrical Consumption  
Energy Consumption  
Dimensions (W × D × H)  
Max. 1.2 kW, 1.5 Wh in Sleep Mode  
DP-1810P: 23.1 × 23.8 × 18.0 in (588 × 605 × 458 mm)  
DP-2010E: 23.1 × 23.8 × 22.6 in (588 × 573 × 573 mm)  
DP-1810P: 90 lb (41 kg)  
Weight  
DP-2010E: 113 lb (51 kg)  
Temperature: 50 - 86°F (10 - 30°C) Relative Humidity: 30 - 80 %  
Operating Environment  
(However, the humidity should be 70 % or less at a temperature of 86°F (30°C),  
and the temperature should be 86°F (30°C) or less at a humidity level of 85 %.)  
CSpecifications are subject to change without notice.  
55  
Specifications  
I ADF (DA-AS180)  
DA-AS180  
Letter, Invoice: 50 sheets (20 lb)  
Ledger, Legal: 30 sheets (20 lb)  
Tray Capacity  
Paper Size  
Invoice/Letter/Legal/Ledger  
14 28 lb (50 110 g/m2)  
Supplied from the copier  
22.0 × 19.7 × 4.4 in (558 × 501 × 112 mm)  
11.0 lb (5.0 kg)  
PaperWeight  
Electrical Requirements  
Dimensions (W × D × H)  
Weight  
I i-ADF (DA-AR201)  
DA-AR201  
Letter, Invoice: 50 sheets (20 lb)  
Ledger, Legal: 30 sheets (20 lb)  
Tray Capacity  
Paper Size  
Invoice/Letter/Legal/Ledger  
14 28 lb (50 110 g/m2)  
Supplied from the copier  
21.7 × 20.5 × 5.3 in (552 × 520 × 135 mm)  
20.5 lb (9.3 kg)  
PaperWeight  
Electrical Requirements  
Dimensions (W × D × H)  
Weight  
I 2nd/4th Paper Feed Module (DA-DS182)  
DA-DS182  
Paper Size  
Invoice/Letter/Legal/Ledger  
16 24 lb (60 90 g/m2)  
Supplied from the copier  
21.7 × 6.1 × 23.0 in (550 × 155 × 585 mm)  
20.9 lb (9.5 kg)  
PaperWeight  
Electrical Requirements  
Dimensions (W × D × H)  
Weight  
I 3rd Paper Feed Module (DA-DS183)  
DA-DS183  
Paper Size  
Invoice/Letter/Legal/Ledger  
PaperWeight  
16 24 lb (60 90 g/m2)  
Supplied from the copier  
21.7 × 6.1 × 23.0 in (550 × 155 × 585 mm)  
20.9 lb (9.5 kg)  
Electrical Requirements  
Dimensions (W × D × H)  
Weight  
CSpecifications are subject to change without notice.  
56  
Options and Supplies  
I
The DP-1810P/2010E is a digital photocopier which can produce images with great clarity.  
Furthermore, its copying functionality can also be greatly enhanced by the addition of the following  
options and supplies.  
We hope you find that the wide ranging capabilities will make your office-place more productive and efficient.  
I Options  
Part Name  
Part No.  
DA-AS180  
DA-AR201  
Remarks  
Also referred as ADF  
Automatic Document Feeder  
Inverting Automatic Document Feeder  
2nd/4th Paper Feed Module  
Also referred as i-ADF (For DP-2010E only)  
(2nd Paper Feed Module is standard on DP-2010E)  
(4th Paper Feed Module is for DP-2010E only)  
DA-DS182  
3rd Paper Feed Module  
Plain Stand (High)  
Plain Stand (Medium)  
Plain Stand (Low)  
Base Stand  
DA-DS183  
DA-DA180  
DA-DA181  
DA-DA182  
DA-DA183  
DA-SM08B  
DA-SM16B  
DA-SM64B  
DA-SM28B  
(3rd Paper Feed Module is for DP-2010E only)  
For USA/Canada only  
For USA/Canada only  
For USA/Canada only  
For USA/Canada only  
Image Memory (8 MB)  
For Electronic Sorting and Sort Printing  
For Electronic Sorting and Sort Printing  
For Electronic Sorting and Sort Printing  
For Electronic Sorting and Sort Printing  
I
mage Memory (16 MB)  
Image Memory (64 MB)  
Image Memory (128 MB)  
I For Printer  
Part Name  
Part No.  
Remarks  
Printer Controller for PCL6.  
(For Network Printing, DA-NE200 is also required)  
PCL6 Emulation Kit  
DA-PC210  
I For Network Printing  
Part Name  
Part No.  
Remarks  
Network Interface Board  
10/100 Ethernet Interface/  
Internet Fax Kit  
DA-NE200  
I Supplies  
Part Name  
Part No.  
Remarks  
Toner Waste Container included  
Toner Bottle  
DQ-TU10C  
PCL6 is a Page Description Language of the Hewlett-Packard Company.  
NOTE  
57  
58  
59  
U.S.A. Only  
WARRANTY  
PANASONIC DOCUMENT IMAGING COMPANY MAKES NO WARRANTIES, GUARANTEES OR  
REPRESENTATIONS, EXPRESSED OR IMPLIED, TO THE CUSTOMER WITH RESPECT TO THIS  
PANASONIC MACHINE, INCLUDING BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF  
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE.  
PANASONIC DOCUMENT IMAGING COMPANY ASSUMES NO RISK AND SHALL NOT BE SUBJECT  
TO LIABILITY FOR ANY DAMAGE, INCLUDING, BUT NOT LIMITED TO DIRECT, INDIRECT, SPECIAL,  
INCIDENTAL OR CONSEQUENTIAL DAMAGES OR LOSS OF PROFITS SUSTAINED BY THE  
CUSTOMER IN CONNECTION WITH THE USE OR APPLICATION OF THIS PANASONIC MACHINE.  
SEEYOUR DEALER FOR DETAILS OF DEALERS WARRANTY.  
For Service, Call:  
Panasonic Document Imaging Company  
A Business Unit of Matsushita Electric Corporation of America  
Two Panasonic Way  
Panasonic Canada Inc.  
5770 Ambler Drive,  
Mississauga, Ontario L4W 2T3  
Secaucus, New Jersey 07094  
S0402-0  
DZSD001728-0  
April 2002  
Printed in Japan  

Masterbuilt Hitch Haul Bike Carrier Hedb2 User Manual
Motorola H550 User Manual
Pitney Bowes Addressright Da750 User Manual
Rival Vs120 User Manual
Samsung Aw12p1hba User Manual
Schumacher 200 30 User Manual
Sunbeam Air Conditioner Ky 25 User Manual
Tripp Lite Battery Module Compartment Subf2030 User Manual
Xerox Copycentre C128 User Manual
Xerox Dcc250 User Manual