Panasonic Dp 1510p User Manual

Digital Imaging Systems

DP-1810P

with Options

Operating Instructions

(For Copier)

DP-2010E

with Options

Model No.

DP-1510P/1810P/2010E

Before operating this equipment, please read these instructions completely and keep these operating

instructions for future reference.

English

Operation Chart

Common Features and Usage

I Basic Operation

Original

1 2 3 4 5

Original Size

(Reduction/

Enlargement

Only)

Copy Size

(Reduction/ of Copies

Enlargement

Number

Press

START

Place the

Original

Load Paper

Turn the Power

Switch On

Only)

I Position of the Original

From ADF (or i-ADF)

From Platen

Original Guide

CPlace originals face down on the

platen or face up on the ADF.

CIf the original is not positioned

properly, a portion of the original

may not be copied.

CFor originals smaller than A5 size,

position the original within the area

of A5 and select A5.

FLS

ADFTray

FLS1

FLS2

Original Guides

Adjust to the original’s width

I Commonly Used Functions and Operating Procedures

Full Size

(See page 12)

Makes a copy that is the same

size as the original

1 4 5

Reduction or Enlargement

Copies the original at a fixed

reduction or enlargement ratio

(See page 13)

1 2 3 4 5

I Memory Capacity

When the memory becomes full during original scanning, the message “OUT OF MEMORY”

“CONTINUE? 1:YES 2: NO” will be displayed in the message display. In this case, follow the

operating instruction in the message display.

When additional memory is required, consult with an authorised servicing dealer.

Energy Star

As an ENERGY STAR^®Partner, Panasonic has determined that this product meets the

ENERGY STAR^®guidelines for energy efficiency.

This voluntary program specifies certain energy consumption and usage standards. This

product will automatically “power down” after a specified period of non-use. The use of this

ENERGY STAR^®compliant product will reduce energy consumption and ultimately benefit the

environment.

The default functions can be adjusted depending on your office requirements.

Please ask your authorised Panasonic dealer for more details.

Table of Contents

Getting To KnowYour Machine

Operation Chart .............................................................................................................................. 3

I Common Features and Usage..............................................................3

Energy Star ..................................................................................................................................... 4

Before Starting

Precautions ..................................................................................................................................... 7

I For Your Safety .....................................................................................7

I Handling ...............................................................................................8

I Toner and Paper ...................................................................................8

I Ventilation .............................................................................................8

I Installation ............................................................................................9

Control Panel ................................................................................................................................ 10

Making Copies

Basic Copy .................................................................................................................................... 12

I Full Size Copying................................................................................12

I Reduction or Enlargement Copying ....................................................13

I Zoom Copying ....................................................................................14

I Using the Sheet Bypass .....................................................................15

Creative Features ......................................................................................................................... 16

I 2 in 1 Copy .........................................................................................16

I 2 Page Copy .......................................................................................17

I Book/Edge/Margin ..............................................................................18

I 2-Sided/1-Sided Copy.........................................................................19

I 1 \ 2/2 \ 1/2 \ 2 Copy....................................................................20

I Book \ 2 Copy ..................................................................................21

I Job Memory .......................................................................................22

I Sort Copy ...........................................................................................23

Other Features .............................................................................................................................. 24

I Energy Saver/Interrupt Mode..............................................................24

I Skyshot Mode.....................................................................................25

Combined FunctionTable ............................................................................................................ 27

Function ........................................................................................................................................ 28

I Checking the Copier’s Total Counter ...................................................28

I General Functions ..............................................................................29

I Copier Settings ...................................................................................30

I General Functions for Key Operator ...................................................31

I Copier Settings for Key Operator ........................................................32

I Function Setting..................................................................................33

I Function Setting for Key Operator.......................................................34

Table of Contents

Options

Accessories .................................................................................................................................. 39

I Components .......................................................................................39

I Automatic Document Feeder ..............................................................40

Problem Solving

Problem Solving ........................................................................................................................... 42

I Adding Paper (J) ...............................................................................42

I Adding the Toner and Replacing Waste Toner Container (?) .............43

I Removing a Misfed Paper...................................................................45

Troubleshooting ........................................................................................................................... 52

I Before Calling Service ........................................................................52

I User Error Codes (U Code) ................................................................54

Others

Specifications ............................................................................................................................... 55

Options and Supplies................................................................................................................... 57

Precautions

For Your Safety

I Laser Safety

LASER SAFETY

This unit employs a laser. Only qualified service personnel should

attempt to service this device due to possible eye injury.

CAUTION:

USE OF CONTROLS, ADJUSTMENTS OR PERFORMANCE

PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY

RESULT IN HAZARDOUS RADIATION EXPOSURE.

I Caution Label

(Digital copier with ADF option)

Precautions

Handling

I Do not look directly at the exposure lamp when

copying.

I Do not turn the power switch Off or open the front

panel during copying.

CDo not drop paper clips or other metal objects into

the copier.

Toner and Paper

I Store toner, drum and paper in cool areas with low

humidity.

CUse high quality 60 - 90 g/m²(Sheet Bypass:

56 - 128 g/m²) paper.

CFor optimum performance, it is recommended that

only Panasonic Brand supplies are used in the

copier.

Ventilation

I The copier should be installed in a well-ventilated

area to minimise the ozone density in the air.

I The copier should not be installed in areas with the

following conditions:

CExtremely high or low temperature and humidity.

Ambient conditions

Temperature:

10 – 35°C

Relative humidity: 45 – 80%

CWhere temperature and humidity can change

rapidly, causing condensation.

CDirect exposure to sunlight.

CDirectly in the air conditioning flow.

CIn areas of high dust concentration.

CIn areas of poor ventilation.

CIn areas with chemical fume concentration.

CIn areas with extreme vibration.

CWith unstable or uneven conditions (floors, etc.).

Precautions

Installation

I The maximum power consumption is 1.2 kW.

A properly wired (grounded), dedicated, 6A, 220-240 V AC outlet is required.

Do not use an extension cord.

The power cord on this equipment must be used to disconnect the main power.

Please ensure that the socket outlet is installed near the equipment and is easily accessible.

FORYOUR SAFETY

Caution Note: Disconnect from the mains supply before removing covers.

The mains plug on this equipment must be used to disconnect mains power. Please ensure that the

socket outlet is installed near the equipment and shall be easily accessible.

For U.K.

This appliance is supplied with a moulded three pin mains plug for your safety and convenience.

A 13 amp fuse is fitted in this plug.

Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13

amps and that it is approved by ASTA or BSI to BS1362

Check for the ASTA mark 7 or the BSI mark 6 on the body of the fuse.

If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is

replaced.

If you lose the fuse cover the plug must not be used until a replacement cover is obtained.

A replacement fuse cover can be purchased from your local Panasonic Dealer.

IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET INYOUR OFFICE

THEN THE FUSE SHOULD BE REMOVED AND THE PLUG CUT OFF AND DISPOSED OF SAFELY.

THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED

INTO ANY 13 AMP SOCKET.

If a new plug is to be fitted please observe the wiring code as shown below.

If in any doubt please consult a qualified electrician.

WARNING:THIS APPLIANCE MUST BE EARTHED.

IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

Green andYellow: Earth

Blue

Brown

: Neutral

: Live

As the colours of the wires in the main lead of this appliance may not correspond with the coloured

markings identifying the terminals in your plug, proceed as follows:

The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which

is marked by letter E or by the safety Earth symbol “L” or coloured GREEN or GREEN-AND-YELLOW.

The wire which is coloured BLUE must be connected to the terminal in the plug which is marked

with the letter N or coloured BLACK.

The wire which is coloured BROWN must be connected to the terminal in

the plug which is marked with the letter L or coloured RED.

How to replace the fuse.

Open the fuse compartment with a screwdriver and replace the fuse.

Control Panel

(For DP-2010E only)

Contents

Refer to

2 in 1 Key

Page 16

CFrom two 1-sided originals, side by side, to 1-sided copies.

2 Page Copy Key

CCopying two facing pages on a A3 size original on two separate A4 size

Page 17

Page 23

sheets.

Sort Key

CWhen using Electric Sorting Mode. Optional memory is required.

(

)

MARGIN Key CShifts the image to the right or left.

Page 18

EDGE Key

BOOK Key

CCreates a blank edge.

CEliminates dark inner binding shadows.

Photo;Text/Photo;Text Keys

CSelect the type of original(s) for image density adjustment.

PHOTO

: Originals are mainly composed of photo.

Page 12

TEXT/PHOTO: Combined originals with text and photo.

TEXT : Originals are mainly composed of text.

Exposure Keys (DARKER, LIGHTER)

SET Key CSet the present selection.

Page 12

——

FUNCTION Key

CUse when changing the paper size, initial values for functions (default

values) and key operator settings.

Pages 28 – 37

CLEAR Key CClears the copy count in the display.

——

Page 24

——

ENERGY-SAVER Key

CCan save power while the copier is not in use.

RESET Key CResets all features to the initial power-on state.

CThe Control Panel displayed above shows only copier functions. Please refer to the

appropriate operating instructions for other control panel functions or in the Panasonic

Document Management System CD-ROM for the Printer control panel functions.

CThe illustration above shows the DP-2010E control panel.

NOTE

Control Panel

LCD Display

Warning Indications

J Add Paper

? Add Toner

I Misfeed

2 Call Service

For DP-1510P/1810P

Contents

CStops the copy run.

CUsed to start an operation.

Refer to

——

STOP Key

START Key

——

INTERRUPT Key, MEMORY IN Key, M1/M2 Keys

CInterrupt Key interrupts other copy or print jobs while making copies.

Pages 22, 24

CMemory In Key registers two copy jobs for recall at a later time.

M1/M2 Keys are used to store a Job in Memory or to recall a Job stores in Memory.

Cursor Keys CSelect copy ratio and function modes using (G or F).

——

PAPER TRAY Key

COPY SIZE Key

CUsed to select the paper tray manually.

——

Used to select Reduction/Enlargement only.For additional details, see page 13.

ORIGINAL SIZE Key

Used to select the original size manually. For additional details, see page 13.

——

PRINT Key CWhen selecting the Printer ON/OFF Line.

2-Sided/1-Sided Copy Key

C Used to select 1 \ 2, 2 \ 2 and 2 \ 1, Book \ 2 copying

CThe Control Panel displayed above shows only copier functions. Please refer

to the appropriate operating instructions for other control panel functions or in

the Panasonic Document Management System CD-ROM for the Printer

control panel functions.

NOTE

Basic Copy

Full Size Copying

I Copying the Same Size Originals (1:1)

Copy size is automatically selected.

ORIGINAL SIZE Key CLEAR Key

2 3

Number of Copies*

Place the Original

Press START**

Up to 999

LCD Display (Sample)

READY TO COPY

COPIES:001

Select the Original Size on units

without the ADF/i-ADF Option.

I Manually Selecting Exposure Control or Original Type

# Select the Original Type

PHOTO

:Originals are mainly composed of photo.

TEXT/PHOTO:Combined originals with text and photo.

TEXT :Originals are mainly composed of text.

$ Select Exposure Control

Press the DARKER/LIGHTER keys to adjust the exposure.

Use Clear key when cancelling the copy count.

∗

NOTE

While the copier is warming up, you may position your original on the copier, enter

your copy job selections and press the Start key. The COPY JOB RESERVED

indicator displays until the warm up cycle is completed and the copy job is

automatically started.

∗∗

Basic Copy

Reduction or Enlargement Copying

I Copying with Preset Ratios

RESET

1 2 3 4 5

Place the

Original

Select the

ORIGINAL SIZE

Number of

Copies

Press

START

Select the COPY

SIZE

Example: Reduction

Original size

Copy size

A3 ->A4

[A4B

]

ZOOM: 71% COPIES:001

The correct ratio is automatically selected.

Reduction and enlargement ratios (%)

Copy Size

Original

Size

100

115

141

200

100

122

173

100

141

100

CWhen changing the paper tray, press the

PaperTray key.

CIf the desired copy size is different from the paper size loaded in the paper

tray, use the sheet bypass. (See page 15)

NOTE

CPress the RESET key to cancel all job settings.

Basic Copy

Zoom Copying

I Zoom

RESET

Copies with variable zoom ratios from 50 % to 200 % in 1 % increments.

1 2 3 4 5

Number

of Copies

Place the

Original

Select ORIGINAL

SIZE

(without using

Press

START

Press Cursor (G or F)

keys to select Zoom Ratio

ADF/i-ADF)

A4 ->A4

[A4B

]

ZOOM:125% COPIES:001

(Example: 125 % Zoom)

CWhen changing the paper size after setting the zoom ratio, please use the paper tray

ATTENTION

NOTE

key.

CPress the RESET key to cancel all job settings.

Basic Copy

Using the Sheet Bypass

I Copying on Special Paper, etc.

Place the original.

Open the sheet bypass.

Sheet

Bypass

Pull out the sheet bypass tray

until it stops.

(For A3 size only)

# Place the sheets of paper into

the tray. (approximately up to

50 A4 size sheets 80 /gm²)

Do not fill above.

Insert the paper until it stops.

Side Guides

$ Adjust the side guides.

Incorrect adjustment may cause the

paper to wrinkle, misfeed or skew.

Press START.

CDo not feed curled paper through the sheet bypass to avoid misfeed.

ATTENTION

NOTE

CAdjust the side guides properly to avoid skewing, wrinkling or misfeeding.

Creative Features

2 in 1 Copy

I 2 in 1 Copy

From two 1-Sided originals, side by side, to 1-Sided pages.

1 \ 2 (Layout)*

2 \ 1 (Layout)*

Landscape (Orientation)*

Portrait (Orientation)*

I Procedure

ADF/i-ADF

Face-Up

( )

COPY SIZE Number of Press

1 2 3 4 5

Place the

Originals

Press 2

in 1 key

(Reduction/

Enlargement

Only)

Copies

START

CThe ADF/i-ADF is required for 2 in 1 copy.

CPress the RESET key to cancel all job settings.

NOTE

CNumbers in parenthesis “ ( ) ” represent that, an additional step is required to

activate the feature.

The Orientation and Layout can be set in the Copier Settings function mode.

(See page 30)

∗

Creative Features

2 PAGE COPY

I 2 PAGE Copy

Copying two facing pages on a A3 size original on two separate A4 size sheets.

I Procedure

1 2 3 4 5

ORIGINAL SIZE

(A4 or A3 size Only)

Number of Press

Place the Press the 2

Originals PAGE COPY

key

Copies

START

Platen

A3 size original

Book Mark

Centre book

by length

and width

according

to centre

marks.

CTo reset all job settings, press the RESET key.

NOTE

Creative Features

BOOK/EDGE/MARGIN

I BOOK Key

Eliminates dark inner binding shadows when copying from a book.

I EDGE Key

Creates a blank edge.

I MARGIN Key

Shifts the image to the right or left.

I Procedure

Press Cursor (G or F) keys to adjust

the void width while the button is

blinking. (approx. 5 sec.)

CVoid/Margin width: 5-99 mm

1 2

4 5

Place the

Original

Number

of Copies START

Press

Press BOOK, EDGE

or MARGIN key

Book

Initial Book Margin setting (Factory setting): 20 mm

∗

BOOK MARGIN

CENTER VOID = 20mm∨∧

Edge

Initial Equal Rate setting (Factory setting): 5 mm

Initial Left Margin setting (Factory setting): 10 mm

EQUAL RATE

VOID MARGIN = 5mm

∧

Margin**

LEFT MARGIN

10mm∨∧

Initial setting (Factory setting) can be changed in the Copier Settings function mode.

(See page 30)

∗

NOTE

If a part of the copied image is missing when using the Margin mode, change the

Frame Reduction setting to ON.

(See page 30)

∗∗

CPress the RESET key to cancel all job settings.

Creative Features

2-Sided/1-Sided Copy (For DP-2010E)

I Key Operation

Press 2-Sided/1-Sided Copy key (circulation) to select a 2-Sided/1-Sided Copy function.

2-Sided/1-Sided Copy key

From 1-Sided originals to 2-Sided

copies.

(See page 20)

(See page 21)

(See page 20)

1 \ 2

2 \ 2

From 2-Sided originals to 2-Sided

copies.

From book originals to 2-Sided copies.

Book \ 2

2 \ 1

From 2-Sided originals to 1-Sided

copies.

C2-Sided originals may be handled either manually or automatically using the

i-ADF (DA-AR201).

NOTE

C2-Sided/1-Sided Copy function is only available for DP-2010E.

Creative Features

1 \ 2 / 2 \1 / 2 \ 2 Copy (For DP-2010E)

I 1 \ 2 Copy

I 2 \ 1 Copy

I 2 \ 2 Copy

From 1-Sided originals to

From 2-Sided originals to

2-Sided copies.

1-Sided copies.

2-Sided copies.

(From Copier Platen & i-ADF/

ADF)

(Using i-ADF)

Long Edge (Binding)*

Long Edge (Binding)

Short Edge (Binding)

Short Edge (Binding)*

I Procedure

i-ADF

Face-Up

( )

1 2 3 4 5

Place the

Originals

COPY SIZE

(Reduction/

Number of Press

Copies START

Press 2-Sided/

1-Sided Copy key

(circulation) to

select 1 \ 2, 2 \ 2

or 2 \ 1

Enlargement Only)

Press the I or H key to select

the binding location.

BINDING:LONG EDGE

PRESS < > TO SELECT

(When selecting 1 \ 2 Copy or 2 \ 1 Copy)

CTo reset each selection, press the RESET key.

NOTE

The initial setting of binding location for 1 \ 2 Copy and 2 \ 1 Copy (Long edge or

∗

Short edge) can be set in function mode. (See page 30)

C1 \ 2, 2 \ 2, 2 \ 1 Copy function is only available for DP-2010E.

Creative Features

Book \ 2 Copy (For DP-2010E)

I Book \ 2 Copy

From book originals to 2-Sided copies.

A3 size originals only.

Facing (Book Format)*

Flipping (Book Format)*

( )

1 2 3 4 5

COPY SIZE

Press 2-Sided/

1-Sided Copy key

(circulation) to select

Book \ 2

Number of

Copies

Press

START

Place the

Original on

the Platen

(Reduction/

Enlargement Only*)

Platen

A3 size original

Book Mark

Centre book by

length and width

according to

centre marks.

CTo reset each selection, press the RESET key.

CA3 and FLS/B4 copy sizes cannot be selected.

NOTE

The book format and page order can be set in function mode. (See page 30)

CBook \ 2 Copy function is only available for DP-2010E.

∗

Creative Features

Job Memory

I Two Copy Jobs Can Be Programmed in Memory (M1, M2) for recall at a

later time.

To Store a Job in Memory

#Set up the copy job to be stored in memory,

by first selecting each function you wish the

copier to perform.

$Press the MEMORY IN (F2) key.

JOB MEMORY

PRESS M1,M2 TO STORE.

%Press the M1 (F3) or M2 (F4) key.

To Recall a Job Stored in Memory

&Place the Original

(Press the M1 (F3) or M2 (F4) key.

RECALL JOB MEMORY

The stored contents will be displayed.

)Press START

CStored job(s) will not be deleted even if the power switch is turned Off.

CWhen storing a new job into programmed memory, the previously stored job will be

NOTE

overwritten.

Creative Features

Sort Copy

I Sort Copy

The sort copy has 2 available electronic sorting functions as follows:

Note: Before using the sort copy, select the desired sorting mode by setting its function first

(See page 29).

Sort

Sort-Rotate

Multiple copies

sorted

automatically.

Multiple copies sorted

automatically and

Stacked in alternate

direction.

(Up to A4 size)

Platen Glass

ADF/i-ADF

( )

1 2 3 4 5

COPY SIZE

(Reduction/

Enlargement

Only)

ADF/i-ADF: Place the

Originals

Platen: Place the

First Original

Select the

SORT Mode

Number of Press

Copies START

From Platen Glass only:

ANOTHER ORIGINAL?

1:YES 2:NO

Place next Original

Press START

7 8

Press “1” key.

Repeat steps 6 and 7

until all originals are

ANOTHER ORIGINAL?

1:YES 2:NO

9 10

scanned and stored

into the copier’s memory.

Press “2” key.

CWhen the memory becomes full during original scanning, the message

“OUT OF MEMORY” “CONTINUE? 1:YES 2: NO” will be displayed in the

message display. If this occurs, follow the instructions in the message

display.

NOTE

For additional memory consult your authorised servicing dealer.

CTo reset all job settings, press the RESET key.

CElectronic sorting function is available for DP-1810P/2010E.

Other Features

Energy Saver/Interrupt Mode

INTERRUPT (F1) Key ENERGY-SAVER Key

I These modes can save power while the copier is not

ENERGY SAVER

in use.

Energy Saver Mode

#To enter this mode

Press the ENERGY-SAVER key or the copier will

automatically enter the ENERGY-SAVER Mode after

15 minutes* from the last copy.The indicator will flash.

$To cancel this mode and make copies

Press the ENERGY-SAVER key again.

Sleep Mode

#Automatically enters the Sleep Mode after 30

minutes from the last copy. The copier power will

drop and the indicator will light.

$To make copies, press the ENERGY-SAVER key.

Interrupt Mode

CThis mode can interrupt other copy jobs while

making copies.

INTERRUPT

#Press the INTERRUPT (F1) key, the indicator will

light.

$Make another copy job using the platen glass.

%Press the INTERRUPT (F1) key again to continue

the original job.

Note: The ADF/i-ADF can not be used with interrupt.

(Use only the Platen)

Energy saver time (15 minutes) and Sleep time (30 minutes) can be changed by the

key operator. (See page 31)

∗

NOTE

Modes

Power Consumption

Approximately 90 Wh

Approximately 38 Wh

Approximately 2.2 Wh

Warm UpTime

N/A

Normal Operation

Energy Saver Mode

Sleep Mode

17 sec. recovery

30 sec. recovery

Other Features

Skyshot Mode

I Skyshot allows copying a manuscript without generating dark borders

even if the platen cover or ADF/i-ADF is opened.

Skyshot mode eliminates dark borders around the originals, and is especially convenient for

copying small-sized originals like bank checks or documents with unusual shapes (round, oval,

etc.).These documents can be reproduced without generating any unnecessary black areas

simply by making a copy with the cover open.

Two types of Skyshot modes can be selected;

Digital Skyshot Mode :The scanning area (size) is not pre-determined.

Manual Skyshot Mode:The scanning area (size) is pre-registered into memory (M1 and M2) in

advance. (See page 30)

I Digital Skyshot Mode

Place the Original on

the platen (Opening

the Platen Cover/

ADF/i-ADF)

Press

START Key

Number of

Copies

Note:The default setting of Digital Skyshot Mode is “NORMAL”. In this setting, the unit scans once.

If there are black areas around the borders in the copies, set the Digital Skyshot Mode to

“QUALITY” to soften the dark borders. In this setting, the unit scans twice.

#Press the FUNCTION key.

$Press the 2 key to select COPIER SETTINGS.

FUNCTION MODE (1-2)

ENTER NO. OR ∨ ∧

%Press the SET key.

2:COPIER SETTINGS

PRESS SET TO SELECT

&Press 6 and SET key to select DIGITAL

COPIER PARAM.(00-14)

SKYSHOT.

ENTER NO._ OR ∨ ∧

(

Press 1-3 key to select the Digital Skyshot Mode.

1: OFF NONE

06 DIGITAL SKYSHOT

2:NORMAL

2: NORMAL Default setting (usually select this

mode).

3: QUALITY For better definition, select the

Quality mode.

)Press the SET key.

*Press the RESET key.

CAn incorrect exposure may occur when there is a black line at the edge of

the original or an image which the copier interprets as a black pattern in the

Skyshot mode.

NOTE

CAn incorrect position detection of the original may occur when a strong light

shines onto the glass during Skyshot mode.

Other Features

Skyshot Mode

I Manual Skyshot Mode

When using this function, the custom size should be registered into memory (M1, M2) in

advance. (See page 32)

Platen

Upper-

left

corner

1 2 3 4

Place the

Original

Select the Custom

Size (M1 or M2)

Number of Press

Copies

START

#Press the FUNCTION key.

$Press the 2 key to select COPIER SETTINGS.

FUNCTION MODE (1-2)

ENTER NO. OR ∨ ∧

%Press the SET key.

2:COPIER SETTINGS

PRESS SET TO SELECT

&Press 7 and SET key to select MANUAL SKYSHOT.

COPIER PARAM.(00-14)

ENTER NO._ OR ∨ ∧

(

Press 2 or 3 key to select the Custom Size.

07 MANUAL SKYSHOT

1:OFF

1: OFF

NONE

2: M1 ON

3: M2 ON

M1 size is ON*

M2 size is ON*

4: M1, M2 ON Both sizes are ON

)Press the SET key.

*Press the RESET key.

The default size for M1 is: 70(X) × 160(Y) mm, and M2 is: 95(X) × 220(Y) mm

∗

NOTE

CWhen changing the M1 or M2 size, consult with the key operator.

CWhen using the Manual Skyshot mode, M1 and M2 are turned ON and other

job memory cannot be used.

CPress the RESET key to cancel all job settings.

Combined Function Table

2-ORIGINAL

H COPY

Other

Functions

Margin

SORT

Remarks

Selections

First

Selections

Zoom Copy

O O O O O O O

2 in 1 Copy

2 Page Copy

1 \ 2

A A O A A A

A A A A A A

O A A A A A

2 \ 2

Book \ 2

2 \ 1

Book

O O O O O O A

O O O O O O O

Edge

Margin

Non-Sort

Sort

Sort-Rotate

Manual Skyshot

Interrupt

✕ ✕ A A A A

–

✕ O ✕ ✕ ✕ ✕

O: Possible Combined Functions.

✕ : Unavailable Combined Functions.

A : Next Selection is Carried Out.

– : Indicates that SORT mode cannot be used. Non-sort operation is carried out.

Function

I Using Function Modes to Change the Initial Copy Modes

Options

General

Functions

Copier

Settings

Printer

Settings

LAN Settings

Input Identification Code

General

Functions for

Key Operator

Copier

Settings for

Key Operator

LAN Settings

for Key

Operator

Printer

Settings for

Key Operator

FUNCTION Key

I Procedure

RESET Key

COPY SIZE PAPER

Key TRAY Key

#Press the FUNCTION Key

FUNCTION MODE (1-2)

ENTER NO. OR ∨ ∧

$Press 1 (GENERAL FUNCTIONS) or 2

(COPIER SETTINGS) key.You may also use

the (G or F) keys.

%Press the SET key.

&Press the Keypad to select function modes

or use the (G or F) keys.

(Follow the on screen instructions.

)After setting, press the SET key to set up the

function.

I Checking the Copier’sTotal Counter

To display the copier’s Total Counter, press the COPY SIZE and PAPERTRAY keys

simultaneously.

CPlease refer to each option’s operating instructions for function settings.

NOTE

Function

General Functions

Initial

Setting

No.

Modes

Function

Selects the sort mode.

SORT MODE DEFAULT

NON-SORT

OFF

CNON-SORT, SORT (For DP-1810P/2010E)

SORT MEMORY USAGE

DEPT. COUNTER

Displays the amount of sort memory used on

the panel.

COFF, DISPLAY

(For DP-1810P/2010E)

Copy usage and copy limit of the selected

department and total copy usage will appear

on the screen.

Consult

your

service

technician.

SORT-ROTATE DEFAULT

KEY OPERATOR MODE

Select Sort-Rotate mode.

OFF

COFF, ON

(For DP-1810P/2010E)

Input the key operator ID code.

Function

Copier Settings

Initial

Setting

No.

Modes

Function

MARGIN DEFAULT

Selects the margin position and shift value.

CPOSITION (Left, Right, Top, Bottom)

CVALUE (5 - 99 mm)

POSITION

10 mm

EDGE DEFAULT

Selects the edge mode (Equal Rate = set the EQUAL RATE

same value for X & Y or Individual = set the

value for X & Y individually) and width.

CEQUAL RATE (X &Y ), INDIVIDUAL

C5 - 99 mm

5 mm

BOOK MARGIN DEF.

FRAME MARGIN

Selects the book Centre Void margin width.

C5- 99 mm

20 mm

INVALID

OFF

Select the reduction ratio in margin mode.

CINVALID, VALID

2-SIDED MODE DEF.

2 in 1 WITH FRAME

DIGITAL SKYSHOT

MANUAL SKYSHOT

Function sets the duplex priority mode.

COFF, 1 \ 2, 2 \ 2, Book \ 2 (For DP-2010E)

Selects whether or not to disable edge deletion. INVALID

CINVALID, VALID

Enables or disables the use of skyshot mode.

COFF, NORMAL, QUALITY

NORMAL

OFF

Enables or disables the use of Manual

Skyshot.

COFF; M1 ON; M2 ON; M1, M2 ON

AUTO EXPOSURE

Automatically adjusts the copy density for text

and photographic originals.

VALID

CINVALID, VALID

1 \ 2 BINDING DEF.

2 \ 1 BINDING DEF.

BOOK \ 2 DEFAULT

Selects the binding location for 1 \ 2 Copy.

LONG EDGE

LONG EDGE, SHORT EDGE (For DP-2010E)

Selects the binding location for 2 \ 1 Copy.

LONG EDGE, SHORT EDGE (For DP-2010E)

Selects the page order and book format for

Book \ 2 Copy.

FLIPPING

L \ R

1. BOOK FORMAT (1: FACING, 2: FLIPPING)

2. PAGE ORDER (1: L \ R, 2: R \ L) (For DP-2010E)

2 in 1 DEFAULT

Selects the orientation and layout for 2 in 1 Copy. ORIENTATION

CORIENTATION (Portrait, LANDSCAPE)

L \ R

CLAYOUT (L \ R, R \ L)

2 PAGE MODE DEF.

Selects the 2 page mode.

CL \ R, R \ L

L \ R

KEY OPERATOR MODE

Input key operator ID code.

CCertain Functions or Parameters are available for selection only when their

NOTE

respective option is installed.

Function

General Functions for Key Operator

Initial

Setting

Consult your

service technician.

No.

Modes

PAPER SIZE

Function

Sets the paper size of each paper tray.

CTray-1, Tray-2, Tray-3, Tray-4

Selects the Control Panel reset time.

COFF, 30 sec, 1 min., 2 min., 3 min., 4 min.

1 min.

AUTO RESET TIME

Sets the Energy Saver mode and time.

CINVALID, ENERGY-SAVER, SLEEP

Energy save mode timer : 1-120 minutes

SLEEP

ENERGY SAVER MODE

Sleep mode timer

: 1-120 minutes

Selects the message language of the display.

CA-ENGLISH, C-FRENCH, SPANISH

LANGUAGE DEFAULT

SPECIAL TRAY 1

A-ENGLISH

Sets the paper tray for special paper (ex: coloured). NONE

CNONE, TRAY 1, TRAY 2, BYPASS

SPECIAL TRAY 2

Sets the paper tray for special paper.

CNONE, TRAY 1, TRAY 2, BYPASS

NONE

SOFT

Sets the panel touch sound.

COFF, SOFT, LOUD

KEY/TOUCH BEEP

BYPASS SET BEEP

Sets the sound when put paper(s) on bypass

INVALID

tray.

C1: INVALID 2: VALID

ORIG. SET BEEP ADF

DEPT. COUNTER MODE

Sets the sound when put paper(s) on ADF.

C1: INVALID 2: VALID

VALID

Monitors copy usage of each department.

(1) TOTAL COUNTER

Consult

your

service

technician.

(2) DEPT. COUNTER

(3) DEPT. COUNTER LIST

TOTAL COUNT

Total print out volume from the main unit.

PC PRINT COUNT

TCP/IP ADDRESS

Total print out volume from the PC.

Contact

your

Network

Adminstrator.

Sets the IP Address assigned to your machine.

∗

C3 digit × 4 (Use the MEMORY IN key to

enter the “.” between each set of 3-digit

numbers)

Contact

your

Network

Adminstrator.

TCP/IP SUBNET MSK

TCP/IP G/W ADDR.

COPY SETTING LIST

Sets the Subnet Mask.

∗

C3 digit × 4 (Use the MEMORY IN key to

enter the “.” between each set of 3-digit

numbers)

Contact

your

Network

Adminstrator.

Sets the Subnet Mask.

∗

C3 digit × 4 (Use the MEMORY IN key to

enter the “.” between each set of 3-digit

numbers)

Prints list containing Current Setting and

Standard Setting.

CIt is necessary to input the Key Operator ID code before changing items on

this page.

NOTE

CThe Special Tray 1 and 2 are not auto-selectable in the switching mode.

Not available for plain copier, but will be available when installing options

with advanced functions. (See page 57)

∗

Function

Copier Settings for Key Operator

Initial

Setting

No.

Modes

Function

Selects original setting

ORIGINAL (HOME)

T/P

CTEXT, T/P (Text/Photo), PHOTO

(Text/Photo)

TEXT CONTRAST

T/P CONTRAST

PHOTO CONTRAST

MAX. COPY SETTING

M1, SIZE

Selects contrast for Text mode

C1 ~ 5

Selects contrast for Text/Photo mode

C1 ~ 5

Selects contrast for Photo mode

C1 ~ 5

Determines whether to limit number of copies

C1 ~ 999

999

70 × 160 mm

Input a size in memory 1 for frequent usage

size.

(X) (Y)

CX: 5~432/Y: 5~297 mm

(See page 22)

95 × 220 mm

Input a size in memory 2 for frequent usage

size.

CX: 5~432/Y: 5~297 mm

(See page 22)

M2, SIZE

(X) (Y)

MEM. FULL ACTION

Selects the memory full action

CPRINT, CANCEL

CIt is necessary to input the Key Operator ID code before changing items on

NOTE

this page.

Function

Function Setting

I Changing the Auto Exposure Setting

You can select whether the copying density is adjusted automatically for text and photographic

originals.

Press the FUNCTION key.

FUNCTION Key

Proceed as Follows:

#Press the 2 key to select COPIER SETTINGS.

FUNCTION MODE (1-2)

ENTER NO. OR ∨ ∧

$Press the SET key.

2:COPIER SETTINGS

PRESS SET TO SELECT

%Press 8 and SET key to select AUTO

COPIER PARAM.(00-14)

ENTER NO._ OR ∨ ∧

EXPOSURE MODE.

&Press 1 or 2 key to select whether Auto

Exposure is to be carried out or not.

08 AUTO EXPOSURE

2:VALID

(Press the SET key to set up the AUTO

EXPOSURE MODE.

)Press the RESET key to exit the Function mode.

Function

Function Setting for Key Operator

I Changing the Paper Size

The Paper Trays are designed to accommodate A5, A4, A4 R, FLS/B4 and A3 size paper. To

change the paper size, perform the steps shown below.

Press the FUNCTION key.

FUNCTION Key

Proceed as Follows:

FUNCTION MODE (1-2)

ENTER NO. OR ∨ ∧

#Press the 1 key to select GENERAL

(Press 00 and 1 or 2 key to select

FUNCTIONS.

the PAPER SIZE.

1:GENERAL FUNCTIONS

PRESS SET TO SELECT

00 PAPER SIZE

1:TRAY-1[A3i

]

$Press the SET key.

)Press SET to select the paper tray and

press (G or F) keys to set the paper

size.

GENERAL PARAM. (0-9)

ENTER NO._ OR ∨ ∧

Paper size changes are as follows.

%Press 9 key.

09 KEY OPERATOR MODE

A4R FLS1 FLS2

B5 B5R

ENTER PASSWORD=-I I

*Press the SET key to set up the PAPER

&Input the Key Operator ID code (3 digit)

SIZE.

and the SET key.

+Press the RESET key to exit the Function

KEY OPR.MODE (00-25)

mode.

ENTER NO._ OR ∨ ∧

Function

Function Setting for Key Operator

Changing the Paper Guide and Paper Size Indicator in the Paper Tray

#Pull the Paper Tray out and remove

paper.

$Adjust the paper guide a to the

required paper length.

%Adjust the Paper Guide b to the

required paper width.

Pinch the stopper to move the Paper

Guide b.

Paper

Guide a

Stopper

Paper

Guide b

&Change the Paper Size Indicator.

Size

Indicator

(Close the Paper Tray.

CIt is recommended that the paper guide b be fixed in place with screws.

NOTE

Consult an authorised servicing dealer for details on how to fasten with

screws.

Function

Function Setting for Key Operator

I Department Counter

The Key Operator can manage, limit copies, counters and code numbers for each department.

(Maximum department counters: 50)

Press the FUNCTION key.

FUNCTION Key

Proceed as Follows:

FUNCTION MODE (1-2)

ENTER NO. OR ∨ ∧

#Press the 1 key to select GENERAL

&Press the Key Operator ID code (3 digit)

FUNCTIONS.

and SET key.

1:GENERAL FUNCTIONS

PRESS SET TO SELECT

KEY OPR.MODE (00-25)

ENTER NO._ OR ∨ ∧

$Press the SET key.

(Press 14 and the SET key to select

DEPT. COUNTER MODE.

GENERAL PARAM. (0-9)

ENTER NO._ OR ∨ ∧

%Press 9 key.

09 KEY OPERATOR MODE

ENTER PASSWORD=-I I

CTo reset the function mode, press the RESET key.

NOTE

Contact your authorised servicing dealer to enable the Department Counter

feature.

Function

Function Setting for Key Operator

Select the Department Counter Mode.

DEPT.COUNTER MODE

1:TOTAL COUNTER

Press 2 and the SET key.

DEPT. CODE (01-50)

ENTER NO. OR ∨ ∧

Change the Department ID Code, limit the maximum number of copies

and Department Counter number.

#Press the Keypad and the SET key to input the

ID CODE

01:1234

Department ID Code.

01: 1234

Department ID Code

Department No.

$Press the Keypad and the SET key to input the

MAX COPIES

01:123456

maximum number of copies.

01: 123456

Maximun number of copies (6 digits)

Department No.

%Press the Keypad and the SET key (G or F keys) to

DEPT.COUNTER

01:123456

select the Department No.

01: 123456

Counter (6 digits)

Department No.

&Press 0 and the SET key (Input “0”) to clear the counter.

CTo reset the function mode, press the RESET key.

NOTE

Accessories

Components

i-ADF (Inverting Automatic Document Feeder)

(DA-AR201)

ADF (Automatic Document Feeder)

(DA-AS180)

CFeeds original automatically

CDuplexing

CFeeds originals automatically.

C2 in 1 Copy

C2:1 Copy

C2 in 1 Copy

Image Memory

(DA-SM08B/SM16B/SM64B/SM28B)

C8/16/64/128 MB

DP-1810P

CTo increase the memory capacity for

electronic sorting and sort printing.

(For DP-1810P/2010E)

with Options

DP-1510P/1810P

CTo increase the memory capacity for sort

printing. (For DP-1510P)

DP-2010E

with Options

2nd/4th Paper Feed Module

(DA-DS182)

DP-2010E

CTo increase the paper feed sources

and capacity.

Paper Feed Module × 1 (550 sheets)

3rd Paper Feed Module

(DA-DS183)

CTo increase the paper feed sources

and capacity.

PCL6 Emulation Kit

(DA-PC210)

CPrinter Controller for PCL6*

Paper Feed Module × 1 (550 sheets)

10/100 Ethernet Interface/

Internet Fax Kit

(DA-NE200)

CNetwork Interface Board

PCL6 is a Page Description Language of the Hewlett-Packard Company.

∗

NOTE

CThe table below shows the options which are required for various functions.

Contact your authorized servicing dealer for details on combinations of options.

Other

2-ORIGINAL H

Function

Margin

SORT

COPY

Functions

Options

ADF

i-ADF

:Required

Accessories

Automatic Document Feeder

I ADF (DA-AS180) / i-ADF (DA-AR201)

1. Features

#Automatic Original Feeding

CThe ADF/i-ADF tray can hold up to 50 A4 size originals of 80 g/m²paper (up to 30 FLS/B4 or

A3 size originals). It can accommodate from A5 to A3 size originals.

CAutomatic original size detection.

$2 in 1 Copy

CTo make a 1-Sided copy (full size or reduction), from two 1-Sided originals side-by-side.

%Duplex Copying (DA-AR201)

CThe i-ADF allows you to copy 2-sided originals either manually or automatically.

2. Components

CSet the originals up to the upper limit arrow.

ADF (DA-AS180)

i-ADF (DA-AR201)

ADFTray

i-ADFTray

Original Guides

Adjust to the original’s width

Accessories

3. Operation

I Operation Procedure

ADF/i-ADF

Face-Up

( )

1 2 3 4

For Duplex Copy

(If required)

Number of

Copies

Press

START

Place the

Original

Inappropriate Originals

CPaste-ups

CPaper with a smooth surface such as glossy CPressure sensitive or carbon backed papers

and coated papers

CTransparencies

CPaper with excessive curl

CStapled originals

COriginals with a lead edge that is “creased”,

“folded”, “punched” or “glued”

CFreshly printed copies from a laser printer

CTo copy these kinds of originals, use the Platen Glass instead.

NOTE

Problem Solving

Adding Paper (J)

I 550-Sheet Paper Tray

Pull the Paper Tray out.

Place the paper with the copying

surface facing upward.

Special papers, like glossy paper, mailing

labels and transparencies cannot be used

in the paper tray.

Use the Sheet Bypass for special paper.

Make sure paper is not loaded

above the overfill indicator located

in the Paper Tray.

Firmly push the Paper Tray back

into the copier.

CDo not use paper with folds or wrinkles.

ATTENTION

Refer to page 35 for details on adjusting the paper tray size.

CUnused paper should always be placed into a bag and the opening should be sealed

for storage.

If the paper is left exposed, problems such as paper curl, paper jams, wrinkles or

loss of copied image quality may occur.

Problem Solving/U13

Adding the Toner and Replacing Waste Toner Container (?)

Open the Front Cover.

Remove the Waste Toner Container by

slowly pulling it towards the left as

illustrated.

Seal the container with the enclosed

cap and dispose of it properly.

Cap

# Turn the empty Toner Bottle

counter-clockwise until it stops. The

Arrow mark (Unlocked symbol )

visible on the end of the Toner

Bottle is aligned with the Arrow

mark on the machine.

Note: To prevent toner spill, ensure

that the key is facing upwards

before removing the toner bottle.

$ Pull the empty Toner Bottle out.

Note: If the bottle will not pull out from

the machine, turn the bottle

slightly in either direction to

release the key and try it again.

Continued on the next page...

CFor optimum copy quality use the recommended Panasonic toner. Store toner in a cool

dark place. Do not unseal toner before use. Use it as fast as possible after unsealing.

CWhen U13 is displayed the Add Toner Warning Indicator will begin to flash.This message

is to prompt you that the toner bottle is nearly empty (approx. 300-sheets can be printed).

This message will continue to be displayed until the bottle is replaced. When the count-

down counter reaches 0, the copier will stop operating. To clear the message and enable

the copier to operate, replace the empty toner bottle with a new one.

ATTENTION

Problem Solving

Adding the Toner and Replacing Waste Toner Container (?)

# Shake the new Toner Bottle four

or five times to loosen the

contents.

$ Remove the cap from the Toner

Bottle.

# Align the Key of the bottle, also

represented by the Arrow mark

(Unlocked symbol ) visible on

the end of the Toner Bottle with

the Arrow mark on the machine.

Note:To prevent toner spill,

ensure that the key is facing

upwards before installing the

2-1

2-3

bottle.

$ Insert the bottle as far as it will

go, then turn it clockwise (160°,

approx. 1/2 turn) until it locks

(Locked symbol ).

2-2

Incorrect

Correct

Note: If the bottle is not inserted

all the way into the machine

as illustrated, turn the bottle

slightly in either direction to

engage the key and try it

again.

Install a new Waste Toner

Container.

Close the Front Cover.

CDo not reuse the toner from the Waste Toner Container.

ATTENTION

Problem Solving

Removing a Misfed Paper

I Paper Misfeed Indicators and Locations

When a paper misfeed occurs, the misfeed indicator and the misfeed

location(s) will be displayed on the panel display.

I ^{Misfeed Indicator}

For DP-2010E

For DP-1510P/1810P

Paper Misfeed Locations

A: ADF (see page 51), i-ADF(see page 50)

(J70, J71)

B: Copier (Paper Exit, Paper Entry/Transport,

ADU) areas (see page 46-48) (J51 - J59,

J80)

C: Paper Feed Module (see page 49)

(J00 - J50, J81-J89)

CMake sure that the misfeed indicator goes off after removing the misfed

paper.

NOTE

CThe misfeed indicator will not go off if the paper is still jammed in the copier.

Check again and remove all misfed paper.

Problem Solving

Removing a Misfed Paper

I Paper Exit Area

CMake sure that the misfeed indicator

goes off after removing all misfed

paper.

For DP-1510P/1810P

For DP-2010E

Remove the misfed paper.

CMake sure that the misfeed indicator goes off after removing all misfed paper.

ATTENTION

Problem Solving

I Paper Entry/Transport Area

CMake sure that the misfeed indicator

goes off after removing all misfed

paper.

For DP-1510P/1810P

For DP-2010E

Open the Right Cover.

Remove the misfed paper.

If copy paper is fed far into the copier:

#Turn the right paper clearing knob.

$Remove the misfed paper.

#Open the Heat Roller Cover.

$Remove the misfed paper.

%Close the Right Cover.

Caution:This fuser area may be

hot.

Caution

heated

surface

CMake sure that the misfeed indicator goes off after removing all misfed paper.

ATTENTION

Problem Solving

Removing a Misfed Paper

ADU Area (For DP-2010E only)

CMake sure that the misfeed indicator

goes off after removing all misfed

paper.

Open the Right Cover.

Remove the misfed paper.

If copy paper is fed far into the copier;

#Turn the right paper clearing knob.

$Remove the misfed paper.

Close the Right Cover.

Problem Solving

I Paper Feed Module

CMake sure that the misfeed indicator

goes off after removing all misfed

paper.

For DP-1510P/1810P

For DP-2010E

#Pull the paper tray out.

$Remove the misfed paper.

%Return the Paper Tray to the original

position.

#Open the Feed Cover.

$Remove the misfed paper.

%Close the Feed Cover.

CMake sure that the misfeed indicator goes off after removing all misfed

ATTENTION

paper.

Problem Solving

Removing a Misfed Paper

I i-ADF (For DP-2010E only)

CMake sure that the misfeed indicator

goes off after removing all misfed

paper.

#Open the Entry Cover.

$Remove the misfed paper.

%Close the Entry Cover.

#Open the ADF Cover.

$Remove the misfed paper.

%Close the ADF Cover.

&Open and close the Entry Cover to

reset the error.

#Lift up the ADF Input Tray.

$Open the ADF exit cover.

%Remove the misfed paper.

&Close the ADF exit cover.

(Close the ADF Input Tray.

CPush the tab on the centre of the Entry Cover to close it.

CTo prevent original(s) damage, please make sure to open the ADF Cover before

ATTENTION

removing misfed original(s).

Problem Solving

I ADF

CMake sure that the misfeed indicator

goes off after removing all misfed

paper.

For DP-1510P/1810P

#Open the Entry Cover.

$Remove the misfed paper.

%Close the Entry Cover.

#Open the ADF Cover.

Note: To prevent damaging the originals,

open the ADF Cover before

removing the misfed original(s).

$Remove the misfed paper.

%Close the ADF Cover.

&Close the ADF.

CTo prevent original(s) damage, please make sure to open the ADF Cover

ATTENTION

before removing misfed original(s).

Troubleshooting

Before Calling Service

Check

Action

Unit Does Not Operate

Check if the Power Switch is turned On and

that the power cord is connected into the

outlet.

Does the display light?

(No)

(Yes)

Does the Energy Saver key flash (or light)

and displays are turned OFF? (See page

Press Energy Saver key on the Control

Panel.

24)

(No)

Does any of the U## codes and messages

appear on the display?

(U01, U07, U13, U14, U20 and U21)

(See page 54)

Perform actions in accordance with each

message.

(No)

Does the add paper indicator and message

appear on the display? (J)

Add paper. (See page 42)

∗

(No)

Does the paper misfeed indicator and

message appear on the display? (I)

Remove the misfed paper. (See page 45)

(No)

Does E#-## indicator and message appear

on the display?

Turn the copier Off, then On. If the Error

Code does not clear, call for service.

∗

When the Add Toner Warning Indicator begins to flash or is lit, replace the toner bottle with a new

one. After this warning is activated, machine operation will begin with the Toner Charging Mode

(approximately 3 minutes to complete) each time the power switch is turned Off then On or if the

Front/Right Cover is opened and then closed.

∗

Note: When the warning indicator starts flashing, a 300-sheet count-down counter is activated,

and upon reaching 0 the machine will stop operating. The 300-sheet counter is based on

6 % fill, depending on the density some pages may print Blank.

Machine operation and displays are as follows:

1. When turning the power switch to On or opening and then closing the Front/Right Cover, the

machine starts to warm-up and the LCD displays:

PLEASE WAIT...

Troubleshooting

2. The Toner Charging Mode starts and the LCD displays:

CHARGING TONER

AddToner Warning Indicator:

CFlashing = Toner Bottle is nearly empty

CLit

= Toner Bottle is empty

3. This message is displayed for approximately 200 seconds.

CHARGING TONER

❚ ❚ ❚ ❚ ❚

Each “ ❚ ” is approximately 10 sec.

∗

4. This massage will continue to be displayed until the warm-up cycle is completed, and if the toner

bottle was replaced. Upon completion, the Add Toner Warning Indicator automatically turns Off.

Check

Action

Light Copies

Press the Darker key until the indicator

LED is set to Darker. (See page 12)

Does the exposure indicator say “Lighter”?

(Yes)

(No)

Does the add toner indicator and message

appear on the display? (?)

Add Toner. (See page 43)

Marked Copies

Is the copier Platen Glass or Platen Cover

dirty?

Clean the Glass or Platen Cover.

(See page 54)

(Yes)

Troubleshooting

User Error Codes (U Code)

The self-diagnostic functions detect troubles in the important components of the copier.

When any trouble occurs, the copier stops.

Code

U01

Display Message

CLOSE FRONT/RT COVER

CLOSE FEED COVER

Check Points

Front Cover is open.

U07

Feed Cover is open.

TONER IS RUNNING LOW

NO WASTE TONER BOX

1.Toner Cartridge is incorrectly installed.

2. Low Toner or No Toner Waste Container.

U13

1.Toner Waste Container is incorrectly

installed.

2.Toner Waste Container is full of toner.

U14

WASTE TONER BOX IS FULL

U20

U21

CLOSE ADF COVER

ADF Cover is open.

While the copier is initializing, the ADF

Cover was opened. (Optional ADF installed)

CLOSE PLATEN COVER

I If the measures outlined above do not solve the problem, call your Service provider.

Copier Care

I As a rule, clean weekly.

Platen/Platen Cover

Platen

Cover

#Wipe marks off with a cloth and a neutral

detergent.

$Wipe again with a dry cloth.

Platen

(Glass)

Specifications

I DP-1510P/1810P/2010E (Copier)

Type

Desktop

PlatenType

Fixed

Acceptable Originals

Copying Method

Fixing Method

Imaging Method

Resolution

Sheets, Books (max. A3)

Laser Electrophotography

Heat Roller Fixing

Dry-Type Single component imaging

Max. 600 dpi

Maximum Copy Size

Void Area

Max. 5 mm

Warm UpTime

First CopyTime

Multi-Copy Speed

Approx. 30 seconds (20°C)

Approx. 6.5 seconds (A4 , from 1st tray)

DP-1510P : 15 cpm (A4 size)

DP-1810P : 18 cpm (A4 size)

DP-2010E : 20 cpm (A4 size)

Enlargement Ratios

Reduction Ratios

Paper Feed

Preset: 115 %, 122 %, 141 %, 173 %, 200 %

Variable: from 101 to 200 % in 1 % increments

Preset: 87 %, 82 %, 71 %, 58 %, 50 %

Variable: from 99 to 50 % in 1 % increments

Paper Tray (550 sheets × 1) + Sheet Bypass (50 sheets)

2nd Paper Feed Module (550 sheets - option)

3rd Paper Feed Module (550 sheets - option)

4th Paper Feed Module (550 sheets - option)

Paper Tray: 60 - 90 g/m²

PaperWeight

(Sheet Bypass: 56 - 128 g/m²)

Quantity Selector

Max. 999 sheets (Output Tray capacity is 250 sheets)

AC 220 - 224 V, 50/60 Hz, 6.0 A

Electrical Consumption

Energy Consumption

Dimensions (W × D × H)

Max. 1.2 kW, 2.2 Wh in Sleep Mode

DP-1510P/1810P: 588 × 605 × 458 mm

DP-2010E: 588 × 605 × 458 mm

DP-1510P/1810P: 41 kg

Weight

DP-2010E: 42 kg

Temperature: 10 - 35°C Relative Humidity: 45 - 85 %

Operating Environment

(However, the humidity should be 70 % or less at a temperature of 30°C, and

the temperature should be 30°C or less at a humidity level of 85 %.)

CSpecifications are subject to change without notice.

Specifications

I ADF (DA-AS180)

DA-AS180

A4, A5: 50 sheets (70 g/m²)

Tray Capacity

FLS/B4, A3: 30 sheets (70 g/m²)

Paper Size

A5/A4/FLS/B4/A3

50 – 110 g/m²

PaperWeight

Electrical Requirements

Dimensions (W × D × H)

Weight

Supplied from the copier

558 × 501 × 112 mm

5.0 kg

I i-ADF (DA-AR201)

DA-AR201

A4, A5: 50 sheets (70 g/m²)

Tray Capacity

FLS/B4, A3: 30 sheets (70 g/m²)

Paper Size

A5/A4/FLS/B4/A3

50 – 110 g/m²

PaperWeight

Electrical Requirements

Dimensions (W × D × H)

Weight

Supplied from the copier

552 × 520 × 135 mm

9.3 kg

I 2nd/4th Paper Feed Module (DA-DS182)

DA-DS182

Paper Size

A5/A4/FLS/B4/A3

60 – 90 g/m²

PaperWeight

Electrical Requirements

Dimensions (W × D × H)

Weight

Supplied from the copier

550 × 155 × 585 mm

9.5 kg

I 3rd Paper Feed Module (DA-DS183)

DA-DS183

Paper Size

A5/A4/FLS/B4/A3

60 – 90 g/m²

PaperWeight

Electrical Requirements

Dimensions (W × D × H)

Weight

Supplied from the copier

550 × 155 × 585 mm

9.5 kg

CSpecifications are subject to change without notice.

Options and Supplies

The DP-1510P/1810P/2010E is a digital photocopier which can produce images with great clarity.

Furthermore, its copying functionality can also be greatly enhanced by the addition of the following

options and supplies.

We hope you find that the wide ranging capabilities will make your office-place more productive and efficient.

I Options

Part Name

Part No.

DA-AS180

DA-AR201

DA-DS182

DA-DS183

Remarks

Also referred as ADF

Automatic Document Feeder

Inverting Automatic Document Feeder

2nd/4th Paper Feed Module

3rd Paper Feed Module

Also referred as i-ADF (For DP-2010E only)

4th Paper Feed Module is for DP-2010E only

3rd Paper Feed Module is for DP-2010E only

For Electronic Sorting and Sort Printing

(For DP-1810P/2010E)

For Sort Printing (For DP-1510P)

Image Memory (8 MB)

DA-SM8B

DA-SM16B

DA-SM64B

DA-SM28B

For Electronic Sorting and Sort Printing

(For DP-1810P/2010E)

For Sort Printing (For DP-1510P)

mage Memory (16 MB)

For Electronic Sorting and Sort Printing

(For DP-1810P/2010E)

For Sort Printing (For DP-1510P)

Image Memory (64 MB)

Image Memory (128 MB)

For Electronic Sorting and Sort Printing

(For DP-1810P/2010E)

For Sort Printing (For DP-1510P)

I For Printer

Part Name

Part No.

Remarks

Printer Controller for PCL6.

(For Network Printing, DA-NE200 is also required)

PCL6 Emulation Kit

DA-PC210

I For Network Printing

Part Name

Part No.

Remarks

Network Interface Board

10/100 Ethernet Interface/

Internet Fax Kit

DA-NE200

I Supplies

Part Name

Part No.

Remarks

Waste Toner Container included

Toner Bottle

DQ-TU10C

PCL6 is a Page Description Language of the Hewlett-Packard Company.

∗

NOTE

For Service, Call:

Matsushita Electric Industrial Co., Ltd.

Osaka 542-8588, Japan

S0602-1062

DZSD001730-1

June 2002

Printed in Japan

Nextel Comm Brr L User Manual
Panasonic Spherical Bearing Mbyt User Manual
Sears 47006 User Manual
Sears Automobile Parts 8755019 User Manual
Sharp Mx 3610n User Manual
Stearns X00 User Manual
Subaru Robin Power Products Automobile Parts Ey15 3d User Manual
Sunpentown Intl Sf 608r User Manual
Toshiba All In One Printer E Studio190f User Manual
Vector Compact Pro Vec020c User Manual