User’s Guide
MBP11
Baby Monitor
The features described in this user's
guide are subject to modifications
without prior notice.
1
Sound Level LED
Overview of your Parent unit
3 GREEN and 2 RED LEDs turn on and off in real
time to indicate the noise level in baby's room.
When audio is being picked up by microphone of
baby unit, the LEDs light up to in indicate audio level
with reference to the sensitivity setting. The more
LEDs light up, the stronger the sound is.
1
2
If no LED lights up it means the sound level in baby's
room does not exceed the thresholds set through the
parent unit.
The LEDs are also used for indicating the speaker
volume setting on parent unit. The louder you set the
speaker volume, the more LEDs light up.
2
Link Indicator
On when the parent unit is powered on and linked to
the baby unit.
Flashes when the parent unit is out of range from
baby unit.
6
5
Off when the parent unit is powered off.
3
4
3
4
5
6
Power
Press and hold to power on/off the parent unit.
Volume +
Press to increase the speaker volume.
Volume -
Press to decrease the speaker volume.
Charging Indicator
On steadily when in charging mode.
Flashes when low battery is detected.
NOTE
Off even if connected with power adapter but without
battery pack installed.
Important guidelines for installing our Baby
Monitor
Overview of your Baby unit
•
•
•
•
To use your baby unit and parent unit together, you
must be able to establish a radio link between them,
and the range will be affected by environmental
conditions.
Any large metal object, like a refrigerator, a mirror, a
filing cabinet, a metallic doors or reinforced concrete,
between the baby and parent unit may block the radio
signal.
The signal strength may also be reduced by other solid
structures, like walls, or by radio or electrical
equipment, such as TV's, computers, cordless or
mobile phones, fluorescent lights or dimmer switches.
1
2
If the signal is poor, try moving the parent and/or the
baby unit to different positions in the rooms.
1
2
Power Indicator
On when the baby unit is switched on.
Off when the baby unit is switched off.
Power
Press and hold to power on/off the baby unit.
1. SAFETY INSTRUCTIONS ..................................6
2. GETTING STARTED...........................................7
2.1 Baby unit power supply.....................................7
2.2 Parent unit battery installation...........................7
2.3 Belt clip on parent unit and baby unit................8
3. USING YOUR BABY MONITOR.........................9
3.1 Power on/off the parent unit..............................9
3.2 Power on/off the baby unit ................................9
3.3 Adjust speaker volume......................................9
4. DISPOSAL OF THE DEVICE
(ENVIRONMENT)..............................................10
5. CLEANING........................................................10
6. TROUBLESHOOTING......................................11
7. GENERAL INFORMATION...............................12
8. TECHNICAL SPECIFICATIONS.......................15
EC DECLARATION OF CONFORMITY ...........16
5
• Adult assembly is required. Keep small parts away
from children when assembling.
1. SAFETY INSTRUCTIONS
• This product is not a toy. Don't allow children to play
with it.
• This baby monitor is not a substitute for responsible
adult supervision.
WARNING:
STRANGULATION HAZARD - Keep the adapter cord
out of baby's reach.
• Keep this User's Guide for future reference.
• Do not cover the baby monitor with a towel or blanket.
• Never use extension cords with power adapters. Only
use the power adapters provided.
NEVER place the baby monitor or its cord within the cot.
Secure the cord some distance away from baby's reach.
Never use extension cords with AC Adapters. Only
use the AC Adapters provided.
• Test this monitor and all its functions so that you are
familiar with it prior to actual use.
This baby monitor is compliant with all relevant standards
regarding electromagnetic fields and is, when handled as
described in the User's Guide, safe to use. Therefore,
always read the instructions in this User's Guide carefully
before using the device.
• Do not use the baby monitor near water.
• Do not install the baby monitor near a heat source.
• Only use the chargers and power adapters provided.
Do not use other chargers or power adapters as this
may damage the device and battery pack.
• Only insert battery pack of the same type.
• Do not touch the plug contacts with sharp or metal
objects.
• Determine a location for the baby monitor that will
provide the best audio reception of your baby in his
cot.
• Place the baby monitor on a flat surface, such as a
dresser, bureau, or shelf.
• NEVER place the baby monitor or its cord within the
cot.
• Secure the cord to the wall to keep cord away from the
baby's reach.
CAUTION
Risk of explosion if battery is replaced by an incorrect
type. Dispose of used batteries according to the
instructions. Use only battery pack with rating: 2.4V
400mAh.
6
SAFETY INSTRUCTIONS
2.2 Parent unit battery installation
The parent unit comes with a battery pack. Charge the
parent unit before you use it for the first time or when the
parent unit indicates that the battery is low.
2. GETTING STARTED
2.1 Baby unit power supply
Battery JACK
Battery PLUG
DC JACK
DC PLUG
1. Insert the small plug of the power adapter into the
1. Turn the belt clip so that it is in the hanging position.
side of the baby unit.
2. Slide off the battery compartment cover.
2. Connect the other end of the power adapter to the
3. Insert the battery plug of the supplied battery pack
mains socket.
into the battery jack inside the compartment.
NOTE
4. Reattach the battery compartment cover.
Only use the provided power adapter.
GETTING STARTED
7
5. Insert the small plug of the power adapter into the
2.3 Belt clip on parent unit and baby unit
side of the parent unit.
6. Connect the other end of the power adapter to the
mains socket.
7. The Charging Indicator comes on.
NOTE
Only use the provided power adapter.
1. Belt clip mode: applicable for parent unit only.
2. Support stand mode: lift up and turn the belt clip
by half turn to convert into support stand mode.
8
GETTING STARTED
3.3 Adjust speaker volume
3. USING YOUR BABY MONITOR
Please read these instructions carefully, and be reminded
that this baby monitor is just intended as an aid. It is not a
substitute for responsible, correct parental supervision.
There are 6 volume levels on the parent unit, including
VOLUME OFF
.
1. Press
or
on the parent unit to access the
current volume level.
2. Press to increase or
of the parent unit respectively.
3.1 Power on/off the parent unit
1. Provided the parent unit is off, press and hold 0 until
the Link Indicator is on. The parent unit is now
powered on and the parent unit will search for and link
itself to the baby unit.
to decrease the volume
2. Provided the parent unit is on, press and hold 0 until
the Link Indicator is off. The parent unit is now
powered off.
3.2 Power on/off the baby unit
Provided the baby unit is off, press and hold 0 until the
Power Indicator is on. The baby unit is now powered on.
Provided the baby unit is on, press and hold 0 until the
Power Indicator is off. The baby unit is now powered off.
NOTE
If you place the parent and baby units too close together,
you will hear a high pitched noise, this is normal. The units
are designed to be located at a distance from one
another, e.g. in separate rooms.
USING YOUR BABY MONITOR
9
4. DISPOSAL OF THE DEVICE
(ENVIRONMENT)
5. CLEANING
Clean MBP11 with a slightly damp cloth or with an anti-
static cloth. Never use cleaning agents or abrasive
solvents.
At the end of the product lifecycle, you
should not dispose of this product with
normal household waste. Take this product
to a collection point for the recycling of
electrical and electronic equipment. The
symbol on the product, user's guide and/or box indicates
this.
Cleaning and care
• Do not clean any part of the product with thinners or
other solvents and chemicals - this may cause
permanent damage to the product which is not
covered by the warranty.
Some of the product materials can be re-used if you take
them to a recycling point. By reusing some parts or raw
materials from used products you make an important
contribution to the protection of the environment.
• Keep your MBP11 away from hot, humid areas or
strong sunlight, and don't let it get wet.
• Every effort has been made to ensure high standards
of reliability for your MBP11. However, if something
does go wrong, please do not try to repair it yourself -
contact Customer Service for assistance.
Please contact your local authorities in case you need
more information on the collection points in your area.
Dispose of the battery pack in an environmentally-friendly
manner according to your local regulations.
10
DISPOSAL OF THE DEVICE (ENVIRONMENT)
• Battery pack in parent unit is running low. Connect the
parent unit to the mains power with the supplied power
adaptor for recharging.
6. TROUBLESHOOTING
Link light on the parent unit does not come on
• Check whether the parent unit is powered on.
• Check whether the supplied battery pack is correctly
installed and that it is not drained.
• Recharge the parent unit by connecting it to the power
supply.
Cannot hear sound or baby cry from the parent unit
• The volume level in the parent unit may be set too low,
increase the volume level of the parent unit. Refer to
section 3.3 for volume level settings.
• The parent unit and the baby unit may be out of range
with each other. Reduce the distance between the
units, but not closer than 1.5 metre.
Link light on the parent unit flashes
• The parent unit and the baby unit may be out of range
with each other. Reduce the distance between the
units, but not closer than 1.5 metre.
• The baby unit may be switched off. Press and hold 0
key to switch on the baby unit.
The baby monitor system produces a high-
pitched noise
• The parent unit and the baby unit are too close to each
other. Make sure the parent unit and baby unit are at
least 1.5 metre away from each other.
• The speaker volume of the parent unit maybe set too
high. Decrease the volume of the parent unit.
Low battery light on the parent unit flashes
• Battery pack in the parent unit is running low. Connect
the parent unit to the mains power with the supplied
power adaptor for recharging.
Battery pack in the parent unit is running low
quickly
• The volume level of the parent unit may be set too high
The parent unit beeps
• Lost connection with the baby unit. Reduce the
distance between the parent unit and the baby unit, but
not closer than 1.5 metre.
• The baby unit may be switched off. Press and hold 0
key to switch on the baby unit.
which consumes power. Decrease the volume level of
the parent unit. Refer to section 3.3 for volume level
settings.
TROUBLESHOOTING
11
What will BINATONE do?
7. GENERAL INFORMATION
If your product is not working properly...
1. Read this User's Guide.
3. Contact Customer Service at
BINATONE or its authorized distributor at its option and
within a commercially reasonable time, will at no charge
repair or replace any Products or Accessories that does
not conform to this Warranty. We may use functionally
equivalent reconditioned/ refurbished/ pre-owned or new
Products, Accessories or parts.
UK
0845 218 0890
ROI
08187 62092
What Other Limitations Are There?
ANY IMPLIED WARRANTIES, INCLUDING WITHOUT
LIMITATION THE IMPLIED WARRANTIES OF
To order a replacement battery pack for parent unit,
contact customer service.
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE, SHALL BE LIMITED TO THE DURATION OF
THIS LIMITED WARRANTY, OTHERWISE THE REPAIR
OR REPLACEMENT PROVIDED UNDER THIS EXPRESS
LIMITED WARRANTY IS THE EXCLUSIVE REMEDY OF
THE CONSUMER, AND IS PROVIDED IN LIEU OF ALL
OTHER WARRANTIES, EXPRESS OF IMPLIED. IN NO
EVENT SHALL MOTOROLA OR BINATONE BE LIABLE,
WHETHER IN CONTRACT OR TORT (INCLUDING
NEGLIGENCE) FOR DAMAGES IN EXCESS OF THE
PURCHASE PRICE OF THE PRODUCT OR
Consumer Products and Accessories
Limited Warranty ("Warranty")
Thank you for purchasing this Motorola branded product
manufactured under license by Binatone Electronics
International LTD ("BINATONE")
What Does this Warranty Cover?
Subject to the exclusions contained below, BINATONE
warrants that this Motorola branded product ("Product") or
certified accessory ("Accessory") sold for use with this
product that it manufactured to be free from defects in
materials and workmanship under normal consumer
usage for the period outlined below. This Warranty is your
exclusive warranty and is not transferable.
ACCESSORY, OR FOR ANY INDIRECT, INCIDENTAL,
SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY
KIND, OR LOSS OF REVENUE OR PROFITS, LOSS OF
BUSINESS, LOSS OF INFORMATION OR OTHER
Who is covered?
This Warranty extends only to the first consumer
purchaser, and is not transferable.
12
GENERAL INFORMATION
FINANCIAL LOSS ARISING OUT OF OR IN
CONNECTION WITH THE ABILITY OR INABILITY TO
USE THE PRODUCTS OR ACCESSORIES TO THE FULL
EXTENT THESE DAMAGES MAY BE DISCLAIMED BY
LAW.
Exclusions
Normal Wear and Tear. Periodic maintenance, repair
and replacement of parts due to normal wear and tear are
excluded from coverage.
Batteries. Only batteries whose fully charged capacity
falls below 80% of their rated capacity and batteries that
leak are covered by this Warranty.
Some jurisdictions do not allow the limitation or exclusion
of incidental or consequential damages, or limitation on
the length of an implied warranty, so the above limitations
or exclusions may not apply to you. This Warranty gives
you specific legal rights, and you may also have other
rights that vary from one jurisdiction to another.
Abuse & Misuse. Defects or damage that result from: (a)
improper operation, storage, misuse or abuse, accident or
neglect, such as physical damage (cracks, scratches,
etc.) to the surface of the product resulting from misuse;
(b) contact with liquid, water, rain, extreme humidity or
heavy perspiration, sand, dirt or the like, extreme heat, or
food; (c) use of the Products or Accessories for
commercial purposes or subjecting the Product or
Accessory to abnormal usage or conditions; or (d) other
acts which are not the fault of MOTOROLA or
Products Covered
Length of Coverage
Consumer Products One (1) year from the date of the
products original purchase by the
first consumer purchaser of the
product.
Consumer
Accessories
Ninety (90) days from the date of
the accessories original purchase
by the first consumer purchaser
of the product.
BINATONE, are excluded from coverage.
Use of Non-Motorola branded Products and
Accessories. Defects or damage that result from the use
of Non-Motorola branded or certified Products or
Accessories or other peripheral equipment are excluded
from coverage.
Consumer Products The balance of the original
and Accessories that warranty or for ninety (90) days
are Repaired or
Replaced
from the date returned to the
consumer, whichever is longer.
GENERAL INFORMATION
13
Unauthorized Service or Modification. Defects or
damages resulting from service, testing, adjustment,
installation, maintenance, alteration, or modification in
any way by someone other than MOTOROLA,
BINATONE or its authorized service centers, are
excluded from coverage.
You will receive instructions on how to ship the Products
or Accessories at your expense and risk, to a BINATONE
Authorized Repair Center. To obtain service, you must
include: (a) the Product or Accessory; (b) the original
proof of purchase (receipt) which includes the date, place
and seller of the Product; (c) if a warranty card was
included in your box, a completed warranty card showing
the serial number of the Product; (d) a written description
of the problem; and, most importantly; (e) your address
and telephone number.
Altered Products. Products or Accessories with (a) serial
numbers or date tags that have been removed, altered or
obliterated; (b) broken seals or that show evidence of
tampering; (c) mismatched board serial numbers; or (d)
nonconforming or non-Motorola branded housings, or
parts, are excluded from coverage.
These terms and conditions constitute the complete
warranty agreement between you and BINATONE
regarding the Products or Accessories purchased by you,
and supersede any prior agreement or representations,
including representations made in any literature
publications or promotional materials issued by
BINATONE or representations made by any agent
employee or staff of BINATONE, that may have been
made in connection with the said purchase.
Communication Services. Defects, damages, or the
failure of Products or Accessories due to any
communication service or signal you may subscribe to or
use with the Products or Accessories is excluded from
coverage.
How to Obtain Warranty Service or Other
Information?
To obtain service or information, please call:
UK
0845 218 0890
ROI
08187 62092
14
GENERAL INFORMATION
8. TECHNICAL SPECIFICATIONS
RF frequency band 1881.792 MHz - 1897.344 MHz
Channels
10
Operating
5ºC to 45ºC
temperature
Baby unit voltage
(Adapter output)
6V DC, 450mA <Tenpao
S004LB0600045; Salcomp VT0601>
Parent unit voltage 2.4V 400mAh Ni-MH battery pack
<BYD H-2/3AAA400X2-LD25; GP
GPRHC043M027>
Parent unit voltage 6V DC, 450mA <Tenpao
(Adapter output)
S004LB0600045; Salcomp VT0601>
TECHNICAL SPECIFICATIONS
15
BINATONE TELECOM PLC
1 Apsley Way London NW2 7HF,United Kingdom.
Tel: +44(0) 20 8955 2700 Fax: +44(0) 20 8344 8877
e-mail: [email protected]
________________________________________
.
EC Declaration of Conformity
The product is labelled with the European Approval Marking CE as
show. Any Unauthorized modification of the product voids this
Declaration.
We the manufacturer / Importer : Binatone Telecom Plc
1 Apsley Way London
NW2 7HF, United Kingdom.
Declare under our sole responsibility that the following product
Type of equipment:
Model Name:
Country of Origin:
Brand:
Digital Baby Monitor
MBP 11
China
Manufacturer / Importer
(Signature of authorized person)
Motorola
complies with the essential protection requirements of R&TTE
Directive 1999/5/EC on the approximation of the laws of the Member
States relating to Radio Spectrum Matters, the Council Directive
2004/108/EC on the approximation of the laws of the Member States
relating to electromagnetic compatibility (EMC) and the European
Community Directive 2006/95/EC relating to Electrical Safety.
Assessment of compliance of the product with the requirements
relating to the essential requirements according to Article 3 R&TTE
was based on Annex III of the Directive 1999/5/EC and the following
standard:
London, 10 Apr 11
Signature: (Paul Tsui/ Product Operation
Director)
Place & Date :
Radio Spectrum:
EMC:
EN301406 V2.1.1 (2009-07)
EN301489-6 V1.3.1 (2008-08)
EN301489-1 V1.8.1 (2008-04)
Electrical Safety:
EN60950-1:2006+A11:2009+A1:2010
16
EC DECLARATION OF CONFORMITY
Manufactured, distributed or sold by Binatone
Electronics International LTD., official licensee
for this product. MOTOROLA and the Stylized
M Logo are trademarks or registered
trademarks of Motorola Trademark Holdings,
LLC. and are used under license. All other
trademarks are the property of their respective
owners.
© 2011 Motorola Mobility, Inc. All rights
reserved.
Version 4.0
Printed in China
|