Napoli Island
ZNA-M90S
ZNA-E42S
Model number:
Serial Number:
MAR09.0102 © Zephyr Corporation
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY NOTICE................................................................. 2-3
LIST OF MATERIALS.......................................................
4
INSTALLATION
Ducting Calculation Sheet.......................................
Mounting Height & Clearance................................
Ducting Options...........................................................
Hood Specifications...................................................
5
6
7
8
Mounting the Hood..................................................... 9 - 10
Ductless Recirculation.............................................. 11
CONTROLS..................................................................................... 12-14
MAINTENANCE
Hood and Filter Cleaning......................................... 15
Lights................................................................................ 16
TROUBLESHOOTING................................................................ 17
LIST OF PARTS AND ACCESSORIES.............................. 18
1
Download from Www.Somanuals.com. All Manuals Search And Download.
READ AND SAVE THESE INSTRUCTIONS
WARNING
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT USE THIS FAN WITH ANY SOLID-STATE CONTROL DEVICE.
WARNING
TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Use this unit only in the manner intended by the manufacturer, if you have questions, contact the manufacturer.
b. Before servicing or cleaning unit, switch power off at service panel and lock panel to prevent power from being switched on accidentally.
When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service
panel.
CAUTION
For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors. Take care when using cleaning
agents or detergents. Suitable for use in household cooking area.
WARNING
TO REDUCE THE RISK OF RANGE TOP GREASE FIRE:
a. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly
on low or medium settings.
b. Always turn hood ON when cooking at high heat or when flaming food
c. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
d. Use proper pan size. Always use cookware appropriate for the size of the surface element.
e. Keep fan, filters and grease laden surfaces clean.
f. Use high setting on hood only when necessary.
g. Don’t leave hood unattended when cooking.
h. Always use cookware and utensils appropriate for the type of and amount of food being prepared.
WARNING
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP FIRE, OBSERVE THE FOLLOWING:
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
b. NEVER PICK UP A FLAMING PAN – You may be burned.
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.
d. Use an extinguisher ONLY if:
1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
a. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards.
Including fire-rated construction.
b. Sufficient air is needed for power combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent
back-drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National
Fire Protection Association (NFPA) and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE) and
the local code authorities.
c. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
d. Ducted fans must always vent to the outdoors.
e. If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application and be connected to a GFI
(Ground Fault Interrupter protected branch circuit).
g. NEVER place a switch where it can be reached from a tub or shower.
h. Make sure the power is off before installing, wiring or maintenancing.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
CAUTION
To reduce risk of fire and to properly exhaust air outside - Do not vent exhaust air into spaces within walls, ceilings,
attics, crawl spaces or garages.
OPERATION
Always leave safety grilles and filters in place. Without these components, operating blowers could catch onto hair, fingers
and loose clothing.
The manufacturer declines all responsibility in the event of failure to observe the instructions given here for installation,
maintenance and suitable use of the product. The manufacturer further declines all responsibility for injury due to
negligence and the warranty of the unit automatically expires due to improper maintenance.
ELECTRICAL REQUIREMENTS
Important:
Observe all governing codes and ordinances.
It is the customer’s responsibility:
-
-
To contact a qualified electrical installer.
To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70
latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 - latest edition** and
all local codes and ordinances.
If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the
ground path is adequate.
Do not ground to a gas pipe.
Check with a qualified electrician if you are not sure the range hood is properly grounded.
Do not have a fuse in the neutral or ground circuit.
*National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
** CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575
This appliance requires a 120V 60Hz electrical supply and connected to an individual properly grounded branch circuit
protected by a 15 or 20 ampere circuit breaker or time delay fuse. Wiring must be 2 wire with ground. Please also refer to
Electrical Diagram on product.
A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, purchase
and install appropriate connector if necessary.
ZNA-M90S - 500 Watts, 4.1 Amps
ZNA-E42S - 500 Watts, 4.1 Amps
3
Download from Www.Somanuals.com. All Manuals Search And Download.
MODELS: ZNA-M90S, ZNA-E42S
PARTS SUPPLIED
1 - Top support frame
1 - Top duct cover
1 - Bottom support frame
1 - Bottom duct cover
1 - 6” round damper,
pre-installed
1 - Hood body
1 - Hardware package
4 - 50W GU-10 halogen lights
3 - Metal mesh filters
HARDWARE PACKAGE CONTENTS
(3) Wire Nuts
(4) M4 x 1-1/2”
Wood Screws
(1) Suction Cup
(4)ø12 OD / ø5 ID
Washers
(2) M4 x 8
Philips Head Screws
PARTS NOT SUPPLIED
- Ducting, conduit and all installation tools
- Cable connector (if required by local codes)
- Duct cover extension accessory - Z1C-00NA
- Recirculating kit accessory - ZRC-0060
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Equivalent number
length x used
Equivalent number
length x used
Duct pieces
Duct pieces
=
To t a l
=
To t a l
Ft.
Ft.
Ft.
Ft.
3-1/ 4” x 10” 1 Ft.
Rect.,
straight
x (
x (
x (
x (
)
)
)
)
=
=
=
=
Ft.
6”- 8”Round 30 Ft.
wall cap
with damper
x (
)
=
7” Round,
straight
1 Ft.
1 Ft.
Ft.
Ft.
6”- 8” Round, 30 Ft.
roof cap
x (
x (
)
)
=
=
8” Round,
straight
6” roundto
3-1/ 4” x 10”
rect.
1 Ft.
transition
3-1/ 4” x 10” 15 Ft.
Rect.900
elbow
Ft.
6” roundto
3-1/ 4” x 10”
rect.
16 Ft.
x (
)
=
transition
900 elbow
Ft.
3-1/ 4” x 10” 9 Ft.
Rect.450
elbow
x (
)
=
Ft.
Ft.
7” or 8”
15 Ft.
9 Ft.
x (
x (
)
)
=
=
Round,
900 elbow
Ft.
Ft.
3-1/ 4” x 10” 24 Ft.
Rect.900
flat elbow
x (
x (
)
)
=
=
7” or 8”
Round,
450 elbow
3-1/ 4” x 10” 30 Ft.
Rect.
wall cap
Ft.
Ft.
Ft.
7” or 8”
Round
wall cap
with damper
30 Ft.
30 Ft.
8 Ft.
x (
x (
x (
)
)
)
=
=
=
with damper
Ft.
Ft.
3-1/ 4” x 10” 5 Ft.
Rect.to
6” round
x (
x (
)
)
=
=
7” or 8”
Round,
roof cap
transition
7” roundto
3 1/ 4” x 10”
rect.
3-1/ 4” x 10” 20 Ft.
Rect.to
6” round
transition
transition
900 elbow
Ft.
7” roundto
3-1/ 4” x 10”
rect.
23 Ft.
x (
)
=
Ft.
6” Round,
900 elbow
15 Ft.
9 Ft.
x (
x (
)
)
=
=
transition
900 elbow
Ft.
Ft.
6” Round,
450 elbow
Subtotal column2 =
Subtotal column1 =
Ft.
Ft.
Ft.
Subtotal column1 =
Total ductwork
=
MaximumDuct Length: For satisfactory air movement,
the total duct length of a 3 1/ 4” x 10” rectangular 6” or 7”
diameter round duct should not exceed 100 equivalent feet.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Minimum mount height between range top to hood
bottom should be no less than 28”.
Maximum mount height should be no higher than
36”.
Min. ducted 33”
Min. recirc. 33”
Max.
48”
It is important to install the hood at the proper
mounting height. Hoods mounted too low could
result in heat damage and fire hazard; while hoods
mounted too high will be hard to reach and will
loose its performance and efficiency.
Min 28"-Max 36"
If available, also refer to range manufacturer’s
height clearance requirements and recommended
hood mounting height above range. Always check
your local codes for any differences.
Min 8’ 1"
Max 10’
Mounting Height (Recirculating or Ducted)
Minimum Ceiling Height 8’1”. Hood mounted 28”
above cooking surface; 64” from floor.
36"
Maximum Ceiling Height 10’ 1”. Hood mounted
36” above cooking surface; 72” from floor.
Duct cover extension kit available for ceiling
heights up to 12 feet. Turn to page 18 for part
number and ordering information.
DUCTING
A minimum of 6” round ducting must be used to
maintain maximum air flow efficiency.
DAMAGE-SHIPMENT / INSTALLATION:
• Please fully inspect unit for damage before
installation.
• If the unit is damaged in shipment, return the
unit to the store in which it was bought for
repair or replacement.
• If the unit is damaged by the customer, repair
or replacement is the responsibility of the
customer.
• If the unit is damaged by the installer (if other
than the customer), repair of replacement must
be made by arrangement between customer
and installer.
Always use rigid type metal ducts only. Flexible
ducts could restrict air flow by up to 50%.
Use calculation worksheet to compute total duct
work.
ALWAYS, when possible, reduce the number of
transitions and turns. If a long duct run is required,
increase duct size from 6” to 7” or 8”.
If turns or transitions are required: Install as far
away from opening and as far apart, between 2,
as possible.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING FIRE HAZARD
NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages.
All exhaust must be ducted to the outside, unless using the recirculating option.
Use single wall rigid Metal ductwork only.
Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape.
Some Ducting Options
Roof Pitch w/
Flashing & Cap
side wall cap
w/ gravity damper
Soffit or crawl space
ductless
recirculating
7
Download from Www.Somanuals.com. All Manuals Search And Download.
front of hood
side of hood
13
16
11
"
9
16
300
8
"
218
9
16
25
"
650
7
16
35
"
900 /42"[1065]
top of hood
(blower housing and ceiling bracket)
3
16
10
8
"
258
208
3
16
"
1
8
1
"
28
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Add Blockings
Fasten upper duct cover
Fasten Support Frame
1. Add and secure blocking (minimum 2x4
studs onto ceiling joists.
2. Fasten mounting telescopic support frame
directly onto ceiling joist or stud blockings.
3. Adjust height requirement and fasten
support frames together. NOTE: If
recirculating the hood, install air diverter
plate onto support frame.
Install Duct Cover
4. Slide upper and lower telescopic duct
duct covers onto support frame. Fasten
upper duct cover piece to frame.
Adjust height & fasten frame
5. Install duct work and electrical
!
CAUTION: At least two installers are
required due to the weight and size of the
hood.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Mount hood onto support frame
6. Lift lower duct cover and hood body onto bottom of support frame.
7. Secure hood body to bottom support with (4) screws. Access the screws
from inside the hood. This will require at least two people.
WARNING: Electrical wiring must be done by a qualified person(s) in
accordance with all applicable codes and standards. This range hood must be
properly grounded. Turn off electrical power at service entrance before wiring.
!
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Ductless recirculation is intended for applications where an exhaust duct work is not possible to be installed.
When converted, the hood functions as a recirculating hood rather than an exhaust hood. Fumes and exhaust
from cooking are drawn and filtered by a set of optional charcoal filters. The air is then purified and re-
circulated back within the home.
We recommend to ALWAYS exhaust air outside of the home by employing existing or installing new duct
work, if possible. The hood is most effective and efficient as an exhaust hood. Only when the exhaust option
is not possible should you recourse to converting the hood into a recirculating hood.
When converted to be a recirculating hood, a set of charcoal filters are required on top of its standard Metal
Filter set. Order according to its Part number below. The standard Metal Filters are intended to capture
residue from cooking and the optional charcoal filters help to purify fumes exhausted from cooking for re-
circulation.
RECIRCULATING KIT (REQUIRED IF NO DUCTING IS USED)
Kit includes charcoal filters and air diverter plate.
Hood Model
ZNA-M90S
ZNA-E42S
Part No.
ZRC-0060
ZRC-0060
Filters in Pkg.
3
3
1. Purchase recirculating kit per the part number above.
2. Secure air diverter plate to top support frame. (FIG. F) Open
sides of air diverter plate should face left and right and align
with louver holes on the duct covers. Run 6” ducting from top
of blower housing and secure to air diverter plate. See manual
included with recirculating kit for more detailed instructions.
FIG. F
3. Remove metal mesh filters from hood. Clip charcoal filters onto
each charcoal filter bracket. (FIG. G) The brackets are pre-installed and
located behind the mesh filters.
front of the hood
4. Re-install metal mesh filters.
5. Enable charcoal filter change indicator on control panel. (Refer details
E
to pg. 13)
6. Charcoal filters must be replaced after every 120 hours of use (or
approximately every 3 to 4 months based on the average of 1 to 2
hrs. of daily cooking time). The microprocessor in the controls when
set, will elapse and count usage time and indicate when charcoal filter
replacement is required every 120 hrs.
D
back of the hood
Charcoal Filter Replacements
Install charcoal filter (plastic side exposed)
into charcoal filter bracket. Insert tab
cut-out side D of charcoal filter into bracket
first. Lock charcoal filter into place by
pushing down on side E with locking tabs.
Hood Model
ZNA-M90S
ZNA-E42S
Part No.
Z0F-C002
Z0F-C002
Qty to Order
3
3
FIG. G
Charcoal Filter Dimensions:
9in x 6 3/8in
228mm x 162mm
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Blower On/Off
Display (speed level, delay off, filter clean/change)
Lights On/Dim/Off
15 Min Delay Off
Adjust 6 Speed Levels
1. Blower On/Off
By pressing
the blower is switched on and off. When switched on, the blower starts up on speed level 3.
2. Speed Selection
The 6 speed levels are selected by pressing
selected.
to decrease and
to increase speed levels. The display indicates levels
3. Delay Off
This feature is used for programmed shut down of blower 15 minutes after the function is activated. Press
once, a dot
flashes in the lower right side of display
minutes.
indicating the function is on. The blowers will shut down after 15
4. Lights On/Dim/Off
Switch lights on by pressing
once, press a second time to dim and again to shut off lights.
5. Display Window
The display window indicates speed levels and features such as metal filter clean reminder, delay off and charcoal filter change
reminder.
Metal Filter Clean Reminder (metal mesh filter)
After every 30 hours of use the display will start flashing an
possible clogs.
F
reminding you to clean the metal filters from residue and
The standard metal mesh filters are required to be cleaned frequently and as recommended in order to maintain blower
efficiency. If improperly maintained, residue from cooking will sift through filters and cause damage to hood blowers and
other sensitive components; and possible clog duct work and create a fire hazard.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Charcoal Filter Change Reminder (charcoal filter, if installed)
When your hood is installed as a recirculating unit, it is fitted with a set of charcoal filters to purify exhaust
and fumes from cooking, then re-circulates the air within the home. These charcoal filters are required to
be replaced after every 120 hours of use. The charcoal filters should never be cleaned or placed in a dish
washer.
The filter change reminder function in the microprocessor needs to be switched on. When switched on, the
microprocessor will elapse and count usage time and indicate by a flashing
replacements are needed.
when charcoal filter
C
Setting the Filter Change Reminder
Set Mode
When off, hold
for approximately 5 seconds.
hold 5 sec. display from < - > to < C >
The display will change from
(exhaust mode) to
C
(recirculating mode) this indicates that the
elapse timer function is switched on and charcoal
filters are used.
C
Filter Replace Indicator
ChangeFIlters
display < C > flashes
C
C
When the display
starts flashing, the charcoal
filters need to be replaced.
Re-setting Function
To Reset
Once filters are replaced, with hood off, press and
hold 5 sec. display from < C > to < >
hold
the display will appear; hold for apprimately
5 seconds until C on displays disappears
.
C
The filter change reminder is now re-set and a new
120 hour elapse cycle is initiated.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Metal Filter Clean Reminder (metal mesh filter)
Whether your hood is installed as an exhaust or purifying unit, a set if metal mesh filters are fitted by the
factory, These metal mesh filters are intended to filter out residue from cooking. They need not be
replaced on a regular basis but are required to be kept clean. The filter clean reminder function in the
F
microprocessor will automatically indicate by a flashing
when the metal mesh filters need to be
cleaned after every 30 hours of use. Filters can be cleaned by hand with non-abrasive soap or in a
dishwasher. Heavily soiled filters should also be soaked in grease cutting detergent prior to cleaning.
Metal Filter Clean Indicator
Clean Filters
F
When
flashes on display, the metal filters
display < F > flashes
installed are required to be cleaned. This will occur
after every 30 hours of use.
F
Re-setting Function
To Reset
Reset the filter clean reminder timer when filters are
cleaned and re-installed (with hood off). Press and
hold 5 sec. display from < F > to < >
hold
for approximately 5 seconds, the display will
F
appear; hold for approximately 5 seconds until
on
F
display disappears
. The filter clean reminder
function is now reset and a new 30 hours elapse
cycle is initiated.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SURFACE MAINTENANCE:
Clean periodically with hot soapy water and clean cotton cloth. Do not use corrosive or abrasive detergent ,
or steel wool/scouring pads which will scratch and damage surface.
For heavier soil use liquid degreaser.
After cleaning it is recommended that you use non-abrasive stainless steel polish/cleaners, to polish and buff
out the stainless luster and grain. Always scrub lightly, with clean cotton cloth, and with the grain.
Do not use any product containing chlorine bleach. Do not use “orange” cleaners.
Metal Filters
The metal filters installed by the factory are intended to filter out residue and grease from cooking. They need
not be replaced on a regular basis but are required to be kept clean.
Filters should be cleaned after every 30 hours of use or once a month.
Remove and clean by hand or in dishwasher on low heat. Spray degreasing detergent and leave to soak if
heavily soiled.
Dry filters and re-install before using hood.
Replacing Metal Filters
Should filters wear out due to age and
prolonged use, replace with following part
number:
Hood Model:
Part No.
Qty. to Order.
ZNA-M90S 50200004
ZNA-E42S 50200004
3
3
Replace any damaged filter that has punctured
or broken mesh or damaged frame.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
REPLACING LIGHT BULBS
CAUTION: Light bulb becomes extremely hot when turned on.
DO NOT touch bulb until switched off and cooled. Touching hot bulbs could cause serious burns.
Make sure all power is turned off and bulbs are not hot.
Remove by turning bulb counter clockwise. Note: Bulb does not unscrew; it turns 60 degrees,
stops and falls out.
If bulbs are difficult to turn due to prolonged use, firmly attach a glass suction cup approximately the diameter of
the bulb or use a rubber/latex glove and turn counter clockwise.
Replacement bulbs are available at specialty lighting stores. Purchase type GU-10 50W halogen. Note: GU-10
halogen light bulbs apply to ZNA hoods ending in serial number xxxxxxxBxx only.
For Zephyr part numbers please turn to page 18 of the manual.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING PROCEDURES FOR NAPOLI ISLAND
Issue
Cause
What to do
After installation, 1. The power source is not turned ON.
the unit doesn’t
1. Make sure the circuit breaker and the unit’s
power is ON.
work.
2. The power line and the cable locking connector
2. Check the power connection with the unit is
connected properly.
is not connecting properly.
3. The switch board and control board wirings are
disconnected.
3. Make sure the wirings between the switch
board and control board are connected
properly.
4. The switch board or control board is defective.
4. Change the switch board or control board.
1. Change the motor.
Light works,
but motor is not
turning.
1. The motor is defective, possibly seized.
2. The thermally protected system detects if the
motor is too hot to operate and shuts the motor
down.
2. The motor will function properly after the
thermally protected system cool down.
3. Damaged capacitor.
3. Change the capacitor.
4. Change defective part.
1. Tighten the motor in place.
2. Replace the blower.
4. The switch board or control board is defective.
1. The motor is not secure in place.
2. Damaged blower wheel.
The unit is
vibrating.
3. The hood is not secured in place.
4. The switch board or control board is defective.
1. Defective halogen bulb.
3. Check the installation of the hood.
4. Change defective part.
1. Change the halogen bulb.
2. Tighten the light bulb.
The motor is
working, but the
lights are not.
2. The light bulb is loose.
The hood is
not venting out
properly.
1. The hood might be hanging to high from the
cook top.
1. Adjust the distance between the cook top and
the bottom of the hood within 28” and 36”
range.
2. The wind from the opened windows or opened
doors in the surrounding area are affecting the
ventilation of the hood.
2. Close all the windows and doors to eliminate
the outside wind flow.
3. Blockage in the duct opening or ductwork.
3. Remove all the blocking from the duct work or
duct opening.
4. The direction of duct opening is against the wind. 4. Adjust the duct opening direction.
5. Using the wrong size of ducting.
5. Change the ducting to at least 6” or higher
for the internal blower and 8” or higher for the
external blower.
Metal Filter is
vibrating.
1. Metal filter is loose.
1. Change the metal filter.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
DESCRIPTION
PART#
Replacement Parts
Light Bulb GU10 50W (each)
Metal Filter (each)
Z0B-0020
50200004
Optional Accessories
Recirculating Kit
Replacement Charcoal Filter (each)
Duct Cover Extension
ZRC-0060
Z0F-C002
Z1C-00NA
18
Download from Www.Somanuals.com. All Manuals Search And Download.
STAPLE YOUR RECEIPT HERE
Proof of the original purchase
date is needed to obtain
Limited Warranty
service under warranty
TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:
1-888-880-8368
Zephyr Corporation (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein
as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or work-
manship as follows:
Two Year Limited Warranty for Parts: For two years from the date of your original purchase of the Products, we will
provide, free of charge, Products or parts to replace those that failed due to manufacturing defects. We may choose, in
our sole discretion, to repair or replace parts before we elect to replace the Products.
One Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will
provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to
manufacturing defects. After the first year from the date of your original purchase, you are responsible for all labor costs
associated with this warranty.
Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts
and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and
service required for the Products and consumable parts such as light bulbs, metal and carbon filters and fuses; (b) any
Products or parts which have been subject to freight damage, misuse, negligence, accident, faulty installation or installa-
tion contrary to recommended installation instructions, improper maintenance or repair (other than by us); (c) commer-
cial use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear of the finish of the Prod-
ucts or wear caused by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner
products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach
you how to use the Products; or (g) damage to the Products caused by accident, fire, floods or act of God. If you are
outside our service area, additional charges may apply for shipping costs for warranty repair at our designated service
locations and for the travel cost to have a service technician come to your home to repair, remove or reinstall the Prod-
ucts. After the first year from the date of your original purchase, you are also responsible for all labor costs associated
with this warranty.
Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSE-
QUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF
THE PRODUCTS. THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF
ALL OTHER EXPRESS WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRAN-
TIES FOR THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Some states or provinces do not
allow limitations on the duration of an implied warranty or the exclusion or limitation of incidental or consequential dam-
ages, so the above limitations or exclusions may not apply to you. To the extent that applicable law prohibits the exclu-
sion of implied warranties, the duration of any applicable implied warranty is limited to the same two-year period
described above. Any oral or written description of the Products is for the sole purpose of identifying the Products and
shall not be construed as an express warranty. Prior to using, implementing or permitting use of the Products, you shall
determine the suitability of the Products for the intended use, and you shall assume all risk and liability whatsoever in
connection with such determination. We reserve the right to use functionally equivalent refurbished or reconditioned
parts or Products as warranty replacements or as part of warranty service. This warranty is not transferable from the
original purchaser and applies in the United States and Canada.
To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or
telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identifi-
cation number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the
request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase
date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documenta-
tion to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.
Zephyr Corporation Service Department, 2277 Harbor Bay Parkway, Alameda, CA 94502 1-888-880-8368
Download from Www.Somanuals.com. All Manuals Search And Download.
JUN08.0101
|