848JN393A1 (704)
G
B
OWNER’S MANUAL
RECIPROCATORS
SGCZ2600DL
SGCZ2600DW
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
SAFETY FIRST
Contents
Instructions contained in warnings within this manual marked
with a
symbol concern critical points which must be taken
1. Parts location .................................................. 3
2. Specifications ................................................. 4
3. Warning labels on the machine ...................... 4
4. Symbols on the machine ................................ 4
5. For safe operation........................................... 5
6. Set up ............................................................. 8
7. Fuel ................................................................. 9
8. Operation ...................................................... 10
9. Maintenance ................................................. 13
10. Storage ......................................................... 15
11. Disposal ........................................................ 15
12. Troubleshooting guide .................................. 16
into consideration to prevent possible serious bodily injury, and
for this reason you are requested to read all such instructions
carefully and follow them without fail.
G
B
WARNINGS IN THE MANUAL
WARNING
This mark indicates instructions, which must be followed in or-
der to prevent accidents, which could lead to serious bodily in-
jury or death.
IMPORTANT
This mark indicates instructions, which must be followed, or it
leads to mechanical failure, breakdown, or damage.
NOTE
This mark indicates hints or directions useful in the use of the
product.
1. Parts location
SGCZ2600DL
(1) Primer
(2) Air cleaner cover
(3) Choke lever
(4) Fuel tank
(5) Starter knob
(6) Spark arrester
(7) Blade
2
3
14
15
1
12
6
10
SGCZ2600DW
(8) Angle transmission
(9) Cutting attachment guard
(10) Handle
13
5
4
12
(11) Shaft tube
11
14
(12) Suspension point
(13) Throttle trigger
(14) Stop switch
(15) Throttle cable
(16) Hip pad
16
15
13
10
11
8
9
7
8
9
7
GB-3
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
2. Specification
Model
Overall size (LxWxH)
Dry weight
SGCZ2600DL
1950 x 430 x 290
7.5
SGCZ2600DW
1950 x 650 x 520
7.8
mm
kg
Engine
Type
Air-cooled 2-stroke gasoline
Model
Zenoah GZ25N
Max output
Idle speed
Displacement cm3
rpm
rpm
1.2Hp (0.9kW) at 7500min-1
3000 200min-1
25.4
Fuel
Mixture (Gasoline 50 : Oil 1) (when using ZENOAH genuine oil)
Carburetor
Spark plug
L
Walbro Diaphragm type
NGK CMR7A
Fuel tank capacity
Transmission
Reduction ratio
0.65
Centrifugal clutch, Rigid drive shaft
7.8
Specifications are subject to change without notice.
3. Warning labels on the machine
15m (50ft)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(1) Read owner’s manual before operating this machine.
(2) Wear head, eye and ear protection.
(3) Wear foot protection.
(4) Wear gloves.
(5) Beware of thrown objects.
(6) Warning / Attention
(7) Keep all children, bystanders and helpers 15 meters away from the machine.
If warning label peels off or becomes soiled and
impossible to read, you should contact the
dealer from which you purchased the product
to order new labels and affix them in the required
location(s).
Never modify your machine.
We won’t warrant the machine, if you use the
remodeled reciprocation or if you don’t ob-
serve the proper usage written in the manual.
4.Symbolson
the machine
The port to refuel the “MIX GASOLINE”
Position: FUEL TANK CAP
For safe operation and maintenance, symbols are carved
in relief on the machine. According to these indications,
please be careful not to make a mistake.
The direction to close the choke
Position: ENGINE COVER
The direction to open the choke
Position: ENGINE COVER
GB-4
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
5. For safe operation
b. At night, at times of heavy fog,
or at any other times when
your field of vision might be
limited and it would be diffi-
cult to gain a clear view of the
working area.
c. During rain storms, during
lightning storms, at times of
strong or gale-force winds, or
at any other times when
weather conditions might
make it unsafe to use the
product.
1. Read this manual carefully until
you completely understand and
follow all safety and operating
instructions.
2. Keep this manual handy so that
you may refer to it later when-
ever any questions arise. Also
note, if you have any questions
which cannot be answered
herein, contact the dealer from
whom you purchased the prod-
uct.
3. Always be sure to include this
manual when selling, lending, or
otherwise transferring the own-
ership of this product.
4. Never allow children or anyone
unable to fully understand the
directions given in the manual
to use the machine.
G
B
WORKING PLAN
1. You should never use the prod-
uct when under the influence of
alcohol, when suffering from ex-
haustion or lack of sleep, when
suffering from drowsiness as a re-
sult of having taken cold medicine
or at any other time when a pos-
sibility exists that your judgment
might be impaired or that you
might not be able to operate the
product properly and in a safe
manner.
WORKING CONDITION
1. When using the product, you
should wear proper clothing and
protective equipment.
(1) Helmet
2. When planning your work sched-
ule, allow plenty of time to rest.
Limit the amount of time over
which the product is to be used
continuously to somewhere
around 30 ~ 40 minutes per ses-
sion, and take 10 ~ 20 minutes of
rest between work sessions. Also
try to keep the total amount of
work performed in a single day
under 2 hours or less.
(2) Ear protectors
(3) Protection goggles or face
protector
(4) Thick work gloves
(5) Non-slip-sole work boots
2. And you should carry with you.
(1) Attached tools
(2) Properly reserved fuel
(3) Spare blade
(4) Things to notify your working
area (rope, warning signs)
(5) Whistle (for collaboration or
emergency)
WARNING
1. If you don’t observe the working
time, or working manner (See
“USING THE PRODUCT”), Re-
petitive Stress Injury (RSI) could
occur.
(6) Hatchet or saw (for removal of
obstacles)
3. Do not wear loose clothing, jew-
elry, short trousers, sandals, or go
barefoot. Do not wear anything
which might be caught by a mov-
ing part of the unit. Secure hair
so it is above shoulder length.
If you feel discomfort, redness and
swelling of your fingers or any
other part of your body, see a doc-
tor before getting worse.
2. To avoid noise complaints, in gen-
eral, operate product between
8 a.m. and 5 p.m. on weekdays
and 9 a.m. to 5 p.m. on weekends.
WORKING CIRCUMSTANCE
1. Never start the engine inside a
closed room or building. Exhaust
gases contain dangerous carbon
monoxide.
NOTE
2. Never use the product,
a. when the ground is slippery
or when you can’t maintain a
steady posture.
Check and follow the local regula-
tions as to sound level and hours of
operations for the product.
GB-5
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
5. For safe operation
BEFORE STARTING
part nor the throttle come into
contact with any obstacle when
the engine starts.
THE ENGINE
1. The area within a perimeter of
15 m (50 ft) of the person using
the product should be considered
a hazardous area into which no
one should enter. If necessary,
yellow warning rope, warning
signs should be placed around the
perimeter of the area. When work
is to be performed simultaneously
by two or more persons, care
should also be taken to constantly
look around or otherwise check for
the presence and locations of
other people working so as to
maintain a distance between each
person sufficient to ensure safety.
2. Check the condition of working
area to avoid any accident by hit-
ting hidden obstacles such as
stumps, stones, cans, or broken
glass.
WARNING
Never place the throttle into the
high-speed position when starting
the engine.
3. After starting the engine, check
to make sure that the cutting at-
tachment stops rotating when the
throttle is moved fully back to its
original position. If it continues to
rotate even after the throttle has
been moved fully back, turn off
the engine and take the unit to
your authorized ZENOAH servic-
ing dealer for repair.
USING THE PRODUCT
IMPORTANT
IMPORTANT
Cut only materials recommended by
the manufacturer. And use only for
tasks explained in the manual.
Remove any obstacle before begin-
ning work.
3. Inspect the entire unit for loose
fasteners and fuel leakage. Make
sure that the cutting attachment
is properly installed and securely
fastened.
4. Be sure to attach the cutting at-
tachment guard securely in place,
or you may get serious injury.
5. Always use the shoulder strap.
Adjust the strap for comfort be-
fore starting the engine. The strap
should be adjusted so the left
hand can comfortably hold the
handlebar grip approximately
waist high.
1. Grip the handles firmly with both
hands using your whole hand.
Place your feet slightly apart
(slightly further apart than the
width of your shoulders) so that
your weight is distributed evenly
across both legs, and always be
sure to maintain a steady, even
posture while working.
2. Keep cutting attachment below
waist level.
3. Maintain the speed of the engine
at the level required to perform
cutting work, and never raise the
speed of the engine above the
level necessary.
4. If the unit starts to shake or vi-
brate, turn off the engine and
check the whole unit. Do not use
it until the trouble has been prop-
erly corrected.
5. Keep all parts of your body away
from rotating cutting attachment
and hot surfaces.
6. Never touch the muffler, spark
plug, or other metallic parts of the
engine while the engine is in op-
eration or immediately after shut-
ting down the engine. Doing so
could result in serious burns or
electrical shock.
STARTING THE ENGINE
1. Keep bystanders and animals at
least 15 m (50 ft) away from the
operating point. If you are ap-
proached, immediately stop the
engine.
2. The product is equipped with a
centrifugal clutch mechanism, so
the cutting attachment begins to
rotate as soon as the engine is
started by putting the throttle into
the start position. When starting
the engine, place the product
onto the ground in a flat clear area
and hold it firmly in place so as to
ensure that neither the cutting
GB-6
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
5. For safe operation
• IF SOMEONE COMES
HANDLING FUEL
1. Guard against hazardous situa-
tions at all times. Warn adults to
keep pets and children away from
the area. Be careful if you are ap-
proached. Injury may result from
flying debris.
2. If someone calls out or otherwise
interrupts you while working, al-
ways be sure to turn off the en-
gine before turning around.
1. The engine of the ZENOAH prod-
uct is designed to run on a mixed
fuel, which contains highly flam-
mable gasoline. Never store cans
of fuel or refill the tank of the unit
in any place where there is a
boiler, stove, wood fire, electrical
sparks, welding sparks, or any
other source of heat or fire which
might ignite the fuel.
G
B
2. Never smoke while operating the
unit or refilling its fuel tank.
MAINTENANCE
1. In order to maintain your product
in proper working order, perform
the maintenance and checking
operations described in the
manual at regular intervals.
2. Always be sure to turn off the en-
gine and disconnect the spark
plug wire before performing any
maintenance or checking proce-
dures.
3. When refilling the tank, always
turn off the engine and allow it to
cool down. Take a careful look
around to make sure that there are
no sparks or open flames any-
where nearby before refueling.
4. Wipe spilled fuel completely us-
ing a dry rag if any fuel spillage
occurs during refueling.
5. After refueling, screw the fuel cap
back tightly onto the fuel tank and
then carry the unit to a spot 3 m
or more away from where it was
refueled before turning on the en-
gine.
WARNING
The metallic parts reach high tem-
peratures immediately after stop-
ping the engine.
3. When replacing the cutting at-
tachment or any other part, or
when replacing the oil or any lu-
bricant, always be sure to use
only ZENOAH products or
products which have been cer-
tified by ZENOAH for use with
the ZENOAH product.
4. In the event that any part must be
replaced or any maintenance or
repair work not described in this
manual must be performed,
please contact a representative
from the store nearest ZENOAH
authorized servicing dealer for
assistance.
TRANSPORTATION
1. When hand-carrying the product,
cover over the cutting part if nec-
essary, lift up the product and
carry it paying attention to the
blade.
2. Never transport the product over
rough roads over long distances
by vehicle without removing all
fuel from the fuel tank. If doing so,
fuel might leak from the tank dur-
ing transport.
5. Do not use any accessory or at-
tachment other than those bear-
ing the ZENOAH mark and rec-
ommended for the unit.
6. Under no circumstances should
you ever take apart the product
or alter it in any way. Doing so
might result in the product be-
coming damaged during opera-
tion or the product becoming un-
able to operate properly.
GB-7
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
6. Set up
WARNING
CONNECTING SWITCH WIRES
• Connect the switch wires between the engine and the
main unit. Pair the wires of the same color.
Never use any screws other than those specified by
the manufacturer, or the engine can get loose, result-
ing in a hazardous event.
HIP PAD
• Wrap the hip pad around the shaft tube as shown in
the figure, and fasten the hooks.
IMPORTANT
Tighten the screws gradually by turns.
MOUNTING ENGINE
1. Install the engine to the drive shaft so that the cylin-
der head and the stop switch may come on the same
side.
2. Using attached four bolts, secure the connection firmly
with equal force (Torque: 25in-lbs)(Torque: 2.8 N.m.).
ANGLE TRANSMISSION
WARNING
The blade has very sharp edges. Be sure to use pro-
tective gloves whenever handling it.
Bolt
1. Remove the fastening screw(long) and the lock
screw(short) from the angle transmission.
2. While aligning the locking holes, install the angle trans-
mission assembly to the shaft casing.
3. While aligning the locking holes, install the bracket.
4. Align the locking holes and screw in the lock screw to
the bottom by hand, then secure it with the wrench
provided. Do not tighten up the lock screw with the
holes out of alignment, or the angle transmission can
be damaged.
INSTALLING HANDLE <SGCZ2600DL>
• Mount the handle to the shaft tube and clamp it at a
location that is comfortable to you.
Locking holes
(2)
About 48cm
(1)
Angle transmission
INSTALLING HANDLE <SGCZ2600DW>
1. Loosen the 4bolts on the upper cap and insert the
handles equally. Retighten the bolts.
(3)
Bracket
2. Put the handle assembly into the bracket and put the
upper cap over it. Tighten the cap securely.
NOTE
If the locking screw is tightened up with the holes out of
alignment, the angle transmission may be damaged.
CONNECTING THROTTLE WIRE
1. Remove the air cleaner cover.
5. Fasten the angle transmission fastening screw.
2. Connect the end of the throttle wire to the joint on the
top of the carburetor.
INSTALLING CUTTING ATTACHMENT GUARD
• Attach the cutting attachment guard with the bolts
provided to the shaft.
GB-8
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
7. Fuel
■ FUEL
3. Pour in all of the oil and agitate well.
4. Pour in the rest of gasoline and agitate again for at
least one minute. As some oils may be difficult to
agitate depending on oil ingredients, sufficient agi-
tation is necessary for the engine to last long. Be
careful that, if the agitation is insufficient, there is an
increased danger of early piston seizing due to ab-
normally lean mixture.
WARNING
• Gasoline is very flammable. Avoid smoking or
bringing any flame or sparks near fuel. Make sure
to stop the engine and allow it cool before refuel-
ing the unit. Select outdoor bare ground for fuel-
ing and move at least 3 m (10 ft) away from the
fueling point before starting the engine.
G
B
5. Put a clear indication on the outside of the container
to avoid mixing up with gasoline or other containers.
6. Indicate the contents on outside of container for easy
identification.
■ FUELING THE UNIT
1. Untwist and remove the fuel cap. Rest the cap on a
dustless place.
2. Put fuel into the fuel tank to 80% of the full capacity.
3. Fasten the fuel cap securely and wipe up any fuel
spillage around the unit.
• The Zenoah engines are lubricated by oil specially
formulated for air-cooled 2-cycle gasoline engine use.
If Zenoah oil is not available, use an anti-oxidant added
quality oil expressly labeled for air-cooled 2-cycle
engine use (JASO FC GRADE OIL or ISO EGC
GRADE).
WARNING
1. Select bare ground for fueling.
2. Move at least 3 meters (10 feet ) away from the
fueling point before starting the engine.
3. Stop the engine before refueling the unit. At that
time, be sure to sufficiently agitate the mixed gaso-
line in the container.
• Do not use BIA or TCW (2-stroke water-cooling type)
mixed oil.
■ FORYOUR ENGINE LIFE, AVOID:
1. FUEL WITH NO OIL (RAW GASOLINE) – It will cause
severe damage to the internal engine parts very
quickly.
2. GASOHOL – It can cause deterioration of rubber and/
or plastic parts and disruption of engine lubrication.
3. OIL FOR 4-CYCLE ENGINE USE – It can cause spark
plug fouling, exhaust port blocking, or piston ring
sticking.
■ RECOMMENDED MIXING RATIO
GASOLINE 50 : OIL 1
(WHEN USING ZENOAH GENUINE OIL)
• Exhaust emission are controlled by the fundamen-
tal engine parameters and components (eq.,
carburation, ignition timing and port timing) with-
out addition of any major hardware or the intro-
duction of an inert material during combustion.
• These engines are certified to operate on unleaded
gasoline.
• Make sure to use gasoline with a minimum octane
number of 89RON (USA/Canada: 87AL).
• If you use a gasoline of a lower octane value than
prescribed, there is a danger that the engine tem-
perature may rise and an engine problem such as
piston seizing may consequently occur.
4. Mixed fuels which have been left unused for a pe-
riod of one month or more may clog the carburetor
and result in the engine failing to operate properly.
5. In the case of storing the product for a long period of
time, clean the fuel tank after rendering it empty. Next,
activate the engine and empty the carburetor of the
composite fuel.
6. In the case of scrapping the used mixed oil container,
scrap it only at an authorized repository site.
NOTE
• Unleaded gasoline is recommended to reduce the
contamination of the air for the sake of your health
and the environment.
As for details of quality assurance, read the description
in the section Limited Warranty carefully. Moreover, nor-
mal wear and change in product with no functional influ-
ence are not covered by the warranty. Also, be careful
that, if the usage in the instruction manual is not observed
as to the mixed gasoline, etc. described therein, it may
not be covered by the warranty.
• Poor quality gasolines or oils may damage sealing
rings, fuel lines or fuel tank of the engine.
■ HOW TO MIX FUEL
IMPORTANT
Pay attention to agitation.
1. Measure out the quantities of gasoline and oil to be
mixed.
2. Put some of the gasoline into a clean, approved fuel
container.
GB-9
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
8. Operation
STARTING ENGINE
WARNING
IMPORTANT
Avoid pulling the rope to its end or returning it by releas-
ing the knob. Such actions can cause starter failures.
The cutting head will start rotating upon the engine
starts.
7. Move the choke lever downward to open the choke.
And restart the engine.
8. Allow the engine to warm up for a several minutes
before starting operation.
1. Rest the unit on a flat, firm place. Keep the cutting
head off the ground and clear of surrounding objects
as it will start rotating upon starting of the engine.
2. Push the primer pump several times until overflown
fuel flows out in the clear tube.
NOTE
1. When restarting the engine immediately after stop-
ping it, leave the choke open.
2. Overchoking can make the engine hard to start due
to excess fuel. When the engine failed to start after
several attempts, open the choke and repeat pulling
the rope, or remove the spark plug and dry it.
STOPPING ENGINE
1. Release the throttle trigger and run the engine for a
half minute.
2. Shift the stop switch to the “Stop” position.
3. Move the choke lever to the closed position.
choke lever
IMPORTANT
close
open
Except for an emergency, avoid stopping the engine
while pulling the throttle trigger.
ADJUSTING THROTTLE CABLE
The normal play is 1 or 2mm when measured at the car-
buretor side end. Readjust with the cable adjuster as
required.
[SGCZ2600DL]
[SGCZ2600DW]
(1)
(1)
1
Cable adjuster
1 to 2mm ( 04in )
ADJUSTING IDLING SPEED
1. When the engine tends stop frequently at idling mode,
turn the adjusting screw clockwise.
2
3
2. When the cutting head keeps rotating after releasing
the trigger, turn the adjusting screw counter-clockwise.
(1) Stop switch
4. [SGCZ2600DL] Set the stop switch to the “ ” posi-
tion. Set the throttle trigger to the start position (1 → 2
→ 3).
Place the unit on a flat, firm place.
Keep the cutting head clear of everything around it.
[SGCZ2600DW] Set the stop switch to the “RUN”
position. Place the unit on a flat, firm place. Keep the
cutting head clear of everything around it.
5. Place the unit on a flat, firm place. Keep the cutting
head clear of everything around it.
Idle adjusting screw
NOTE
6. While holding the unit firmly, pull out the starter rope
quickly.
Warm up the engine before adjusting the idling speed.
GB-10
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
8. Operation
HARNESS
(DW)
While holding the unit by your left
hand securely, press the red button
of the buckle.
Then take the harness off from your
shoulders.
WARNING
ALWAYS WEAR THE PROVIDED HARNESS WHEN
USING THE MACHINE!
Always make sure the machine is hooked securely
to the harness.
If you don't, you will be unable to control the machine
safely.This can result in injury to yourself or others.
Never use a harness with a defective quick release
or any other damage.
G
B
(1)
(1) Buckle
(DW: Double strap)
USAGE
This machine does cutting not by a rotary cutter like con-
ventional trimmers but by a pair of special blades, each
upper blade and lower blade oscillate opposite direc-
tion alternately within a limited angle at a speed of ap-
proximately 1/30 of conventional trimmers.
HOW TO WEAR
1. Wear the provided harness without twisted bands, with
the hanger on your right side.
This unique mechanism brings you many benefits like
the following:
1. Since the blade does not cause grass chips and
pebbles to the thrown around, you may use less care
about your clothing or surroundings.
(1)
2. Should the blade hit a rigid object like stones, trees
or steel poles during operation, it does not produce a
bounce motion that can cause loss of machine con-
trol.
3. Since the blade does not cause cut grass to wrap
around the neck, you need not to stop operation to
remove such wrappers.
(DL: Single strap) (DW: Double strap)
(1) Hanger
(1)
BALANCE THE UNIT
1. Hook your machine to the hanger.
2. Adjust the bands of the harness to have the blade
parallel to the ground when standing in your normal
working position to provide you most effectiveness
and comfort on operating the machine.
What's more, since the whole circle of the blade is avail-
able for cutting, you can move the cutting head in all di-
rections and cut grass growing on such place difficult-to-
get with conventional trimmer.
3. In order to prevent the hanger position to change
during operation, turn up the extra part of the band
from the buckle.
You can even trim the waterside without splashing water.
HOW TO USE
4. When correctly adjusted, check the correct working
of the harnesses' QUICK RELEASE.
•
•
Adjust the front handle to the most comfortable position.
Start the engine and pull the throttle trigger gradually. The
blades will start moving as the engine speed goes up.
• To stop the blade motion, simply release the throttle
trigger. The clutch will disengage and the blades stop
moving while the engine keeps idling.
• Move the cutting head as sliding its bottom on the
ground. This will help you do the job with less effort.
NOTE
a) Avoid running the engine at full throttle with no load.
Continuous no load full throttle operation can cause
damage to the engine and the drive shaft.
QUICK RELEASE
The harness is equipped with a "QUICK RELEASE"devise.
To release the machine from the harness in emergency
situations, please follow the procedure as explained
below.
b) Operation at too slow engine speed can cause ab-
normal vibration of the machine, resulting in short life
of drive shaft and clutch parts. If you felt such vibra-
tion, use a higher speed range.
WARNING
c) Though the blades are made of steel harder than con-
ventional metal blades, continuous cutting in soil will
accelerate wear.
Make sure to check proper working of the QUICK RE-
LEASE device BEFORE operating the machine.
Make sure to hold the unit securely when using the
QUICK RELEASE.
(DL)
While holding the unit by your
right hand securely, press both
(1)
sides of the
buckle. sides of the buckle.
(1) Buckle
(DL: Single strap)
GB-11
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
8. Operation
CUTTING WORK
•
Road edge
This machine does cutting not by a rotary cutter like con-
ventional trimmers but by a pair of special blades that
moves round within a limited angle at a speed of ap-
proximately 1/30 of conventional trimmers. This unique
mechanism has brought you many benefits as follow-
ing;
1. Since the blade does not cause grass chips and
pebbles to be thrown around, you may use less care
about your clothing or surrundings.
2. Should the blade hit a rogid object like stones, trees
or steel poles during operation, it does not produce a
bounce motion that can cause loss of machine con-
trol.
•
Near fences
3. Since the blade does not cause cut grass to wrap
around the neck, you need not to stop operation to
remove such wrappers.
4. What's more, since the whole circle of the blade is
available for cutting, you can move the cutting head
in all directions and cut grass growing on such place
difficult-to-get by conventional trimmers. You can even
trim the waterside without splashing water.
•
Around stones
WARNING
For your health and to prevent the risk from vibration,
refrain from working for a long time at the cold tempera-
ture.
RECOMMENDED APPLICATIONS
•
Among trees
•
Parking area
•
Waterside
•
Roadside
GB-12
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
9. Maintenance
MAINTENANCE CHART
Every Every Every
25 50 100
Before
use
System/components
Procedure
Note
hours hours hours
after after after
G
B
fuel leaks, fuel spillage
fuel tank, air filter, fuel filter
wipe out
✔
✔
inspect/clean
see adjusting
idling speed
clean and readjust
plug gap
✔
replace, if necessary
replace carburetor
if necessary
GAP: .025 in (0.6 ~ 0.7 mm)
replace, if necessary
idle adjusting screw
✔
spark plug
✔
cylinder fins, intake air cooling vent clean
✔
muffler, spark arrester, cylinder exhaust port
clean, remove piled up carbon
✔
throttle trigger, stop switch
check operation
replace if
something’s wrong
grease
tighten/replace
make sure to attach
✔
✔
cutting parts
angle transmission
screws/nuts/bolts
cutting attachment guard
✔
✔
✔
✔
except adjusting screws
•
•
Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool.
Use protective gloves whenever inspecting, removing, sharpening, and installing the blades.
• Replace with new blades when the tooth width be-
came less than 8mm at the tip. (c)
• As the extent of wear differs by each tooth depend-
ing on use conditions, rotate the blade position at in-
tervals.
BLADE
Wipe off dust and dirt attached to the blades, and oil
them after every use.
To sharpen blade:
1. When the cutting edges have become dull, sharpen
them by using a small disk grinder. (a)
To remove blades:
1. Turn over the machine and remove the bottom cover
(1) by removing the 4 screws.
2. Loosen 4 screws and remove the lower blade (2)
3. Loosen 4 screws and remove the upper blade (3).
2. When sharpening, offset the teeth of upper and lower
blades by 3mm. (b) To offset, insert the hexagon
wrench into the socket on the top of the angle trans-
mission and rotate it.
To install blades:
The upper and lower blades are interchangeable. When
fastening the blade mounting screws, torque them uni-
formly.
GB-13
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
9. Maintenance
WARNING
IMPORTANT
Make sure that the engine has stopped and is cool
before performing any service to the machine. Con-
tact with moving cutting head or hot muffler may re-
sult in a personal injury.
• Note that using any spark plug other than those des-
ignated may result in the engine failing to operate
properly or in the engine becoming overheated and
damaged.
• To install the spark plug, first turn the plug until it is
finger tight, then tighten it a quarter turn more with a
socket wrench.
AIR FILTER
• The air filter, if clogged, will reduce the engine perfor-
mance. Check and clean the filter element in warm,
soapy water as required. Dry completely before in-
stalling. If the element is broken or shrunk, replace
with a new one.
(9.8 ~ 11.8 N.m.)
TIGHTENING TORQUE:
87 ~ 104 in-lbs
MUFFLER
WARNING
•
Inspect periodically, the muffler for loose fasten-
ers, any damage or corrosion. If any sign of ex-
haust leakage is found, stop using the machine
and have it repaired immediately.
Air Filter
•
Note that failing to do so may result in the engine
catching on fire.
FUEL FILTER
• When the engine runs short of fuel supply, check the
fuel cap and the fuel filter for blockage.s
SPARK ARRESTER
• The muffler is equipped with a spark arrester to pre-
vent red hot carbon from flying out of the exhaust out-
let. Periodically inspect and clean as necessary with
a wire brush.
Fuel filter
Spark arrester
SPARK PLUG
• Starting failure and mis-firing are often caused by a
fouled spark plug. Clean the spark plug and check
that the plug gap is in the correct range. For a re-
placement plug, use the correct type specified by
ZENOAH.
ANGLE TRANSMISSION
• Periodically refill the case with grease (every 25 hours).
• Use only lithium based greases.
Grease:
approx. 10cc
Screw
Air purge
Plane washer
0.6 to 0.7 mm
•
REPLACEMENT PLUG IS A NGK CMR7A.
Bolt
Grease: approx. 5cc
GB-14
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
9. Maintenance
INTAKE AIR COOLING VENT
WARNING
PROCEDURES TO BE PERFORMED AFTER EV-
ERY 100 HOURS OF USE
1. Remove the muffler, insert a screwdriver into the vent,
and wipe away any carbon buildup. Wipe away any
carbon buildup on the muffler exhaust vent and cylin-
der exhaust port at the same time.
•
Never touch the cylinder, muffler, or spark plugs
with your bare hands immediately after stopping
the engine. The engine can become very hot when
in operation, and doing so could result in severe
burns.
G
B
2. Tighten all screws, bolts, and fittings.
3. Check to see if any oil or grease has worked its way
in between the clutch lining and drum, and if it has
wipe it away using oil-free, lead-free gasoline.
•
When checking the machine to make sure that it
is okay before using it, check the area around the
muffler and remove any wood chips or leaves
which have attached themselves to the machine.
Failing to do so could cause the muffler to become
overheated, and that this in turn could cause the
engine to catch on fire. Always make sure that the
muffler is clean and free of wood chips, leaves,
and other waste before use.
•
Check the intake air cooling vent and the area
around the cylinder cooling fins after every 25
hours of use for blockage, and remove any waste
which has attached itself to the machine. Note that
it is necessary to remove the engine cover shown
in (A) in order to be able to view the upper part of
the cylinder.
10. Storage
Aged fuel is one of major causes of engine starting fail-
ure. Before storing the unit, empty the fuel tank and run
the engine until it uses all the fuel left in the fuel line and
the carburetor. Store the unit indoor taking necessary
measures for rust prevention.
IMPORTANT
• If waste gets stuck and causes blockage around the
intake air cooling vent or between the cylinder fins, it
may cause the engine to overheat, and that in turn
may cause mechanical failure on the part of the ma-
11. Disposal
chine.
Cylinder
When disposing your machine, fuel or oil for the machine,
be sure to allow your local regulations.
(A)
Intake air cooling vent
GB-15
Download from Www.Somanuals.com. All Manuals Search And Download.
SGCZ2600DL/SGCZ2600DW
12. Troubleshooting guide
Case 1. Starting failure
CHECK
fuel tank
fuel filter
PROBABLE CAUSES
→ incorrect fuel
→ fuel filter is clogged
ACTION
→ drain it and use correct fuel
→ clean
carburetor adjustment screw → out of normal range
→ adjust to normal range
→ clean/dry
→ correct (GAP: 0.6 ~ 0.7 mm)
→ retighten
sparking (no spark)
spark plug
→ spark plug is fouled/wet
→ plug gap is incorrect
→ disconnected
Case 2. Engine starts but does not keep running/hard re-starting
CHECK
PROBABLE CAUSES
ACTION
fuel tank
→ incorrect fuel or staled fuel → drain it and use correct fuel
carburetor adjustment screw → out of normal range
muffler, cylinder (exhaust port) → carbon is built-up
→ adjust to normal range
→ wipe away
→ wash
air cleaner
→ clogged with dust
→ clogged with dust
cylinder fin, fan cover
→ clean
When your unit seems to need further service, please consult with our ZENOAH service shop in your area.
Limited warranty
Should any failure occur on the product under normal oper-
ating conditions within the applicable warranty period, the
failed part will be replaced or repaired free of charge by a
ZENOAH authorized dealer.
THE COMPANY IS LIABLE FOR DAMAGES TO OTHER
ENGINE COMPONENTS CAUSED BY THE FAILURE OF A
WARRANTED PART STILL UNDER WARRANTY.
THE WARRANTY DOES NOT APPLY TO THOSE UNITS
WHICH HAVE BEEN DAMAGED BY NEGLIGENCE OF IN-
STRUCTION LISTED IN THE OWNER/OPERATOR MANUAL
FOR PROPER USE AND MAINTENANCE OF THE UNITS
ACCIDENT MISHANDLING, ALTERATION, ABUSE, IM-
PROPER LUBRICATION, USE OF ANY PARTS OR ACCES-
SORIES OTHER THAN THOSE SPECIFIED BY THE COM-
PANY, OR OTHER CAUSES BEYOND THE COMPANY’S
CONTROL.
WARRANTY PERIOD: 1 year (6 months if used profession-
ally, and 30 days if used for rental purpose) from the date of
initial purchase.
THE PURCHASER SHALL BEAR COSTS OF TRANS-
PORTING THE UNIT TO AND FROM THE ZENOAH DEALER.
THE PURCHASER SHALL NOT BE CHARGED FOR DIAG-
NOSTIC LABOR WHICH LEADS TO THE DETERMINATION
THAT A WARRANTED PART IS DEFECTIVE, IF THE DIAG-
NOSTIC WORK IS PERFORMED AT THE ZENOAH DEALER.
THIS WARRANTY DOES NOT COVER THOSE PARTS RE-
PLACED BY NORMAL WEAR OR HARMLESS CHANGES
IN THEIR APPEARANCE.
THE PURCHASER OR OWNER IS RESPONSIBLE FOR THE
PERFORMANCE OF THE REQUIRED MAINTENANCE AS
DEFINED BY THE MANUFACTURER IN THE OWNER/OP-
ERATOR MANUAL.
THERE ARE NO OTHER EXPRESS WARRANTIES.
IMPLIED WARRANTIES INCLUDING THOSE OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PUR-
POSE ARE LIMITED TO TWO (2) YEARS OF HOME USE
[ONE (1) YEAR FOR ANY OTHER USE] FROM THE ORIGI-
NAL DELIVERY DATE.
ANY WARRANTED PART WHICH IS NOT SCHEDULED FOR
REPLACEMENT AS REQUIRED MAINTENANCE, OR
WHICH IS SCHEDULED ONLY FOR REGULAR INSPECTION
TO THE EFFECT OF REPAIR OR “REPLACE AS NECES-
SARY” SHALL BE WARRANTED FOR THE WARRANTY PE-
RIOD. ANY WARRANTED PART WHICH IS SCHEDULED
FOR REPLACEMENT AS REQUIRED MAINTENANCE
SHALL BE WARRANTED FOR THE PERIOD OF TIME UP
TO THE FIRST SCHEDULED REPLACEMENT POINT FOR
THE PART.
LIABILITIES FOR INCIDENTAL OR CONSEQUENTIAL
DAMAGE UNDER ANY AND ALL WARRANTIES ARE
EXCLUDED.
IF YOU NEED TO OBTAIN MORE INFORMATION, PLEASE
C A L L Y O U R N E A R E S T S E RV I C E C E N T E R ,
OR CHECK PLEASE ZENOAH WEB SITE
ANY REPLACEMENT PART THAT IS EQUIVALENT IN PER-
FORMANCE AND DURABILITY MAY BE USED IN NON-
WARRANTY MAINTENANCE OR REPAIRS, AND SHALL
NOT REDUCE THE WARRANTY OBLIGATION OF THE
COMPANY.
GB-16
Download from Www.Somanuals.com. All Manuals Search And Download.
|