®
™
Zebra P110i
Card Printer
User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
This manual contains installation and operation information for the Zebra P110i card printers
manufactured by Zebra Technologies Corporation.
Copyright Notice
© 2005, 2006 ZIH Corp.
This document contains information proprietary to Zebra Technologies Corporation. This
document and the information contained within is Copyrighted by Zebra Technologies
Corporation and may not be duplicated in full or in part by any person without written
approval from Zebra Technologies Corporation. While every effort has been made to keep the
information contained within current and accurate as of the date of publication, no guarantee is
given that the document is error-free or that it is accurate with regard to any specification.
Zebra Technologies Corporation reserves the right to make changes, for the purpose of product
improvement, at any time.
Trademarks
P110i is a trademark and Zebra is a registered trademark of Zebra Technologies Corporation.
Windows is a registered trademark of Microsoft Corp. All other trademarks or registered
trademarks are marks of their respective holders.
980515-001 Rev. A
P110i User’s Manual
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
Product Disposal
Product Disposal
Product Disposal Information • Do not dispose of this product in unsorted municipal
waste. This product is recyclable, and should be recycled according to your local
standards. For more information, please see our web site at:
Return Materials Authorization
Before returning any equipment to Zebra Technologies Corporation for in-warranty or out-of-
warranty repair, contact Repair Administration for a Return Materials Authorization (RMA)
number. Repack the equipment in the original packing material and mark the RMA number
clearly on the outside. Ship the equipment, freight prepaid, to the address listed below:
For USA, Latin America, and Asia / Pacific:
For Europe and Middle East:
Zebra Technologies Corporation
Zebra Technologies Corporation
Zebra Card Printer Solutions
1001 Flynn Road
Zebra Card Printer Solutions
Pittman Way, Fulwood
Preston, PR2 9ZD
Camarillo, CA. 93012-8706.USA
Phone: +1 (805) 578-5001
FAX: +1 (805) 579-1808
Lancashire, U.K.
Phone: +44 - 1 - 772 - 797555
FAX: +44 - 1 - 772 - 693000
Declarations of Conformity
EN 55022 (1998)
EMC Directive
RF Emissions control
89/336/EEC
EMC Directive
EN 301489-3
V1.4.1
RF Emissions and Immunity for
radio equipment
modified by
92/31/EEC and
EMC Directive
EN55024
(2001)
Immunity to Electro-Magnetic
Disturbances
93/68/EEC
73/23/EEC
modified by 93/
68/EEC
EN 60950-1
(2001)
Product safety
Low voltage Directive
R&TTE
Directive
Radio Frequency Interferences
1999/5/CE
EN300330-2 V1.1.1
For a formal certificate, please contact the Compliance Office at Zebra’s Camarillo facility.
iv
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
Declarations of Conformity
EUROPE: Norway Only: This product is also designed for IT power system with phase to phase
voltage 230V. Earth grounding is via the polarized, 3-wire power cord.
FI: “Laite on liitettävä suojamaadoitus koskettimilla varustettuun pistorasiaan”
SE: “Apparaten skall anslutas till jordat uttag”
NO: “Apparatet må tilkoples jordet stikkontakt”
Model P110i conforms to the following specification: FCC Part 15, Subpart A, Section
15.107(a) and Section 15.109(a) Class B digital device.
Industry Canada Notice
This device complies with Industry Canada ICES-003 class B requirements.
Supplemental Information
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference’s by
one or more of the following measures:
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•
Consult the dealer or an experienced radio/TV technician for help.
The user may find the following booklet, prepared by the Federal Communications
Commission, helpful:
How to identify and resolve Radio/TV Interference Problems. This booklet is available from
the U.S. Government printing Office, Washington, D.C. 20402, Stock No. 004-000-00345-4.
Use of a shielded cable is required to comply within Class B limits of Part 15 of FCC Rules.
Pursuant to Part 15.21 of the FCC Rules, any changes or modifications to this equipment not
expressly approved by Zebra may cause, harmful interference and void the FCC authorization
to operate this equipment.
980515-001 Rev. A
P110i User’s Manual
v
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
Icons
Icons
Throughout this manual, different icons highlight important information, as follows:
Note • Indicates information that emphasizes or supplements important points of the main
text.
Important • Advises you of information that is essential to complete a task, or points out the
importance of specific information in the text.
Electric Shock Caution • Warns you of a potential electric shock situation.
Electrostatic Discharge Caution • Warns you of a situation where electrostatic
discharge could cause damage to electronic components.
Caution • Advises you that failure to take or avoid a specific action could result in
physical harm to you, or could result in physical damage to the hardware.
vi
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
Icons
P110i Printer Model
The Zebra Product Number tells a story:
Here is a quick review of the Zebra Card Printer Series numbering and lettering system to help
you.
Model numbers include identifiers that specify options using the following lettering
conventions:
Part Number
Description
Base Printer
P 1 1 0 i - _ _ _ _ _ - _ _ _
P110i Single Sided Color Card Printer
Smart Card Options
None
_ _ _ _ _ - 0 _ _ _ _ - _ _ _
Magnetic Encoder
None
_ _ _ _ _ - _ 0 _ _ _ - _ _ _
_ _ _ _ _ - _ M _ _ _ - _ _ _
Yes (select defaults below)
Magnetic Encoder Defaults
None
_ _ _ _ _ - _ _ 0 _ _ - _ _ _
_ _ _ _ _ - _ _ 1 _ _ - _ _ _
_ _ _ _ _ - _ _ 3 _ _ - _ _ _
Stripe Down, HiCo/LoCo
Stripe Up, HiCo/LoCo
Memory Expansion
None
_ _ _ _ _ - _ _ _ 0 _ - _ _ _
_ _ _ _ _ - _ _ _ _ A - _ _ _
Interface
USB Only
Power Cords
_ _ _ _ _ - _ _ _ _ _ - I _ _
_ _ _ _ _ - _ _ _ _ _ - U _ _
U. S. and Europe
U. K. and Australia
Windows Drivers and User Documentation / Training included on one CD
(Software & Documentation Package) which contains Multi-language
documentation - English, Spanish, French, German, Chinese, Italian, and
Portuguese
_ _ _ _ _ - _ _ _ _ _ - _ D _
Starter Kit
_ _ _ _ _ - _ _ _ _ _ - _ _ 0
_ _ _ _ _ - _ _ _ _ _ - _ _ S
No Starter Kit
Starter kit (including 200 - 30 mil PVC cards and one YMCKO ribbon, part
number 800015-940)
Example
P110i-0M10A-ID0
P110i Printer, Magnetic Stripe Encoder (HiCoDn), Standard Memory, USB Inter-
face, US and Europe Power Cords, Windows Driver and User Documentation CD
Accessories
105862-001
105912-912
P120i/110i Card SenseTM single card feed upgrade kit
P120i/110i Cleaning Kit, includes 4 print engine cleaning cards and 4 feeder
cleaning cards
980515-001 Rev. A
P110i User’s Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Foreword
Icons
viii
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
• Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii
Product Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Return Materials Authorization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Declarations of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Controls and Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Power Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Power Socket. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
USB Port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Installing the P110i Printer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Installing the Printer Driver. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Printer Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
980515-001 Rev. A
P110i User’s Manual
vii
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Loading Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Card Feeder. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Printing a Test Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Printing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
5 • Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
When to Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
How to Clean . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Cleaning the Print Head . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Card Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Magnetic Encoder Cleaning. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Setting Up the Printer Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Printing a Single Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Website . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
viii
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
1
Getting Started
Unpacking Your Card Printer
Your P110i printer ships in a cardboard carton, protected by styrofoam inserts and a
protective anti-static bag. Keep all packaging material in case you need to move or re-ship
the printer.
1. Before opening and unpacking the printer, inspect the carton to ensure that no damage
occurred during shipment.
2. Ensure that you have a clean and nearly dust free environment for proper operation
and storage of the printer.
3. Unlatch and remove the handle, open the printer carton, and remove the styrofoam
packing material from the top of the printer.
STYROFOAM
PACKING
MATERIAL
PRINTER
PRINTER
ACCESSORIES
HANDLE
980515-001 Rev. A
P110i User’s Manual
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Controls and Indicators
4. Lift the printer out of the carton by holding it on both sides of the bottom and lifting the
printer gently from the carton.
5. Remove the box containing the printer accessories from the shipping carton.
6. Make sure the following accessories are included with your P110i printer:
a. Software CD-ROM
b. Quick Start Guide
c. Cleaning Kit
d. 120 vac and 230 vac Power Cords
e. Power Transformer
f. USB Printer Cable
If any items are missing, please contact your dealer. To reorder, please refer to Appendix C of
this manual.
USB PRINTER
CABLE
CLEANING
QUICK START
GUIDE
KIT
120 VAC &
SOFTWARE
CD-ROM
230 VAC
POWER CORDS
POWER
TRANSFORMER
Controls and Indicators
Your P110i printer is equipped with a Multi Function LCD Readout Panel to provide printer
status information. The readout is controlled by the multi-function control button directly
below the viewing window.
2
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Controls and Indicators
POWER
SOCKET
POWER
SWITCH
USB PORT
Power Switch
The power switch is located at the rear of the printer unit, bottom right.
Power Socket
The power socket is located at the rear of the printer, to the left of the power switch.
USB Port
The USB port is located at the rear of the printer unit, bottom left.
980515-001 Rev. A
P110i User’s Manual
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Controls and Indicators
Multi-Function LCD Panel
MULTI-FUNCTION
LCD PANEL
MULTI-FUNCTION
CONTROL BUTTON
The LCD Panel can display the following messages:
Message
Mode
Operational
Fixed
Fixed
Fixed
Fixed
Initializing
SELF TEST
READY
DOWNLOADING DATA
MAG ENCODING
Fixed
Fixed
PRINTING MONO
Fixed
PRINTING CYAN
Fixed
PRINTING YELLOW
PRINTING MAGENTA
PRINTING BLACK
PRINTING OVERLAY
Fixed
Fixed
Fixed
Fixed
DOWNLOADING FIRMWARE
CLEANING
Fixed
Scrolling
Scrolling
REMOVE RIBBON THEN CLOSE LID
EMPTY FEEDER THEN CLOSE COVER
4
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Controls and Indicators
Message
Mode
Scrolling
Scrolling
Scrolling
Scrolling
Scrolling
Scrolling
Fixed
FEED LONG CLEANING CARD IN EXIT
REMOVE LONG CLEANING CARD
INSERT FEEDER CLEANING CARD
CLOSE FEEDER DOOR
REMOVE FEEDER CLEANING CARD
SINGLE CARD READY-PRINT OR EJECT
INSERT CARD
Scrolling
PUSH BUTTON TO CONTINUE
Warnings (Printer will still operate)
Scrolling
Fixed
REMOVE CARD AT EXIT
CLEAN PRINTER
CHECKING RIBBON
ENCODING ERROR
INVALID MAGNETIC DATA
CHECK RIBBON
Fixed
Fixed
Scrolling
Fixed
Fixed
CLOSE LID
Fixed
FLASH ERROR
Fixed
READING ERROR
Errors (Printer will not operate)
OUT OF RIBBON
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
Fixed
OUT OF CARDS
MECHANICAL ERROR
COVER OPEN
PARAMETERS ERROR
COMMAND ERROR
LID OPEN
OUT OF RIBBON
980515-001 Rev. A
P110i User’s Manual
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Getting Started
Controls and Indicators
6
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
2
Printer Installation
Installing the P110i Printer
Caution • Do not power the printer with USB attached to your computer at this
time. The driver will prompt you when it is time to plug in and power up your
printer.
Connecting the P110i Printer
The following instructions will guide you through the installation of the P110i printer.
Caution • Limit electrical power supplied to the P110i Printer to 24 VDC. Limit
excess current draw to 16 amps or less, using an associated circuit
breaker or other such device. Never operate the printer in a location
where operator, computer, or printer can get wet. Personal injury could
result. The printer must be connected to an earthed electrical power
supply and properly protected against electrical surges and grounding
faults. The power supply pack can only be replaced by the same
product from the manufacturer.
1. Place the printer in a location that allows easy access to all sides. The printer should
never be operated while resting on its side or upside down
980515-001 Rev. A
P110i User’s Manual
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Installing the P110i Printer
2. Remove the yellow CAUTION label from the back of the printer.
3. Ensure that the printer’s power switch in the OFF ( O ) position.
8
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Installing the P110i Printer
115 VAC
230 VAC
4. Insert the power supply plug into the power socket, attach the power cord (120VAC or
230VAC) to the power supply, then plug the power cord in to a grounded electrical socket
of the proper voltage and type.
Caution • Intermittent or unpredictable operation may occur from unsecured
connectors. If damaged, the power cable must be replaced by an exact
equivalent. The socket should always be easily accessible to power off
the printer.
5. Attach USB cable to printer and computer.
980515-001 Rev. A
P110i User’s Manual
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Installing the Printer Driver
Installing the Printer Driver
Caution • Do not power the printer with USB attached to your computer at this time.
The driver will prompt you when it is time to plug in and power up your
printer.
To install the P110i Printer on Windows 2000 and Windows XP operating systems, insert the
User Documentation, Drivers, and Training CD, included with your printer, into your
computer and InstallWizard will walk you through the required installation steps. The
InstallWizard will:
•
•
Automatically install the User Interface when the driver CD is inserted.
Start the installation process when the Install Printer Driver menu item is selected from
the Main Menu.
•
Allow you to install Ethernet drivers, if you plan on networking your card printer via an
external print server
•
•
Check to see which operating system you are using
Detect previous versions of the driver and clean up any unnecessary Windows registry
entries. You must select “Remove” from the install options to remove any previous driver
versions.
•
•
Install the new driver files
Reboot your computer
10
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Installing the Printer Driver
Print Driver Installation
Install the P110i Printer driver as follows:
1. Insert the P110i User Documentation, Drivers, and Training CD into the CD drive of
the host computer. The Select Language window will open.
2. From the Select Language window, choose the appropriate language for your system. The
Main Menu will open in the selected language.
3. From the Main Menu, under Install Printer Driver, select P110i.
980515-001 Rev. A
P110i User’s Manual
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Installing the Printer Driver
4. The InstallShield Wizard will be installed and a progress window will be displayed. Once
the InstallShield Wizard has been installed, the Welcome to InstallShield Wizard
window will open.
5. On the Welcome to InstallShield Wizard window, click the Next button, then follow the
instructions that appear on the screen.
6. At the end of the install, power-on the printer to complete the installation.
12
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Change Printer Driver Options
Change Printer Driver Options
You can change the default settings for the P110i printer driver. Change the options as follows:
1. Select Start>Settings>Printers and Faxes.
2. From the Printers and Faxes list, right click the P110i USB Card Printer and select
Properties from the pop-up menu. The Printer Properties window will open.
3. On the General tab, click on the Printing Preferences button to change the card orientation
settings, monochrome conversion settings, various ribbon settings, or to adjust the color
and head settings properties.
980515-001 Rev. A
P110i User’s Manual
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Change Printer Driver Options
4. On the Sharing tab, you can choose to share the printer over the network, and install
additional drivers to accommodate different operating systems.
5. On the Ports tab, you can add, delete, and configure the printer ports, as well as choose
which port the P110i printer is assigned.
14
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Change Printer Driver Options
6. On the Color Management tab, you can add, remove, or change printer color profiles.
7. Use the Security tab to change permissions for the P110i printer.
980515-001 Rev. A
P110i User’s Manual
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Printer Installation
Change Printer Driver Options
8. On the Advanced tab, you can choose various printer properties, install different printer
drivers, and change default printer settings.
9. On the Device Settings tab, you can change settings for a Magnetic Encoder and change to
or from single feed mode.
10. Once the P110i printer driver options have been configured to your satisfaction, click the
OK button to save your new configuration and close the Properties window.
16
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Setup
Loading Ribbon Cartridge
Loading Ribbon Cartridge
The P110i Printer requires approved ribbon cartridges (see Appendix C). The Resin Thermal
Transfer and Dye Sublimation ribbons are specifically designed for your P110i Printer.
•
•
i Series Printers require the use of i Series ribbons for full color printing.
Each ribbon cartridge includes an integrated adhesive cleaning roller assembly that is
used to clean the cards entering the printer. Improper cleaning will reduce printer life
and degrade print quality
•
When the ribbon is completely used, change the whole cartridge assembly.
Electrostatic Discharge Caution • DO NOT TOUCH the print head or the electronic
components on the print head. Discharge of electrostatic charge from the human body or
other surfaces can damage the print head or other electronic components
1. Open printer lid by pressing the Cover Release button on the top of your printer.
2. Peel protective wrapper from adhesive cleaning roller by gently pulling on the tape.
Discard the protective wrapper.
ADHESIVE CLEANING
ROLLER
3. Insert the ribbon cartridge with the cleaning roller facing down, so the gears on the ends of the
rollers fit into the appropriate slots.
4. Close the printer lid and push down until you hear an audible click.
Note • After the lid is closed, the ribbon automatically synchronizes when the
printer power is on.
18
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Setup
Loading Cards
Loading Cards
To help you load, print, and collect cards, the P110i has the following items:
Card Feeder
The card feeder is used for loading cards, it can hold up to 100 cards of 30 mils thickness. The
card feeder is located under the card feeder cover of the P110i printer.
Caution • DO NOT bend cards or touch print surfaces as this can reduce print
quality.
Note • The surface of the cards must remain clean and dust free. Always store cards in
an enclosed container. Ideally, use cards as soon as possible. If cards stick together,
carefully fan or shuffle them.
Note • For Cards with magnetic stripe refer to Appendix A for loading instructions.
Load cards into card feeder as follows:
1. Open card feeder cover.
2. Slide card guide all the way to the right until it locks in place with an audible click.
CARD
GUIDE
CARD FEEDER
3. Remove cellophane wrapper from card stack.
Note • Static charges and edge burrs from the card die-cutting process can render individual
cards stuck together with significant adhesion force. These cards must be physically
separated from each other before inserting into the feeder; if not separated, feeding or
printing problems may occur.
980515-001 Rev. A
P110i User’s Manual
19
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Setup
Loading Cards
4. Holding the card deck by the sides, hold it vertically against a flat surface such as a
desktop. If the deck is too thick for your hand to hold it comfortably, use about half a deck
at a time.
5. Push the stack back and forth to an angle of about 45° from vertical, so as to separate all of
the cards.
6. Restore the card stack to its original squared-off condition, and place the cards in the input
hopper.
7. Place stack of up to 100 cards into card feeder and close the card feeder cover. When card
feeder cover is closed, the card guide locking mechanism will automatically be released.
CARD FEEDER
COVER
CARD
STACK
CARD
FEEDER
20
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Setup
Printing a Test Card
Card Output Hopper
1. Raise the printer lid and pull the output hopper down to place it in its functional position.
2. When not using the printer, place the card output hopper back in its closed position to
protect the printer from dust.
CARD
OUTPUT
HOPPER
Printing a Test Card
With ribbon cartridge and cards loaded, your P110i printer is ready to print. To check the
operation of the printer, you should print a test card.
1. Place the printer power switch in the OFF (0) position.
2. While holding down the Multi Function Button, place the printer power switch in the
ON ( | ) position. The LCD status window will glow blue.
POWER
SWITCH
MULTI-FUNCTION
SWITCH
P520CEM
Serial N¡ 060376
Firmware: V1.50
Head resistance: 1568
Offset: X002 Y015
-
EC: 0014
Printing Counter: 00002716
3. Keep pressing the Multi Function button until the SELF TEST message appears in the
window.
4. Release the Multi Function button and a test card will print after a few seconds.
980515-001 Rev. A
P110i User’s Manual
21
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Setup
Printing a Test Card
22
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
4
P110i Printer Operation
Printing
Printing with the P110i Printer requires the Windows Printer Driver, your card design/
issuing software or printer command level programming through the printer interface.
The P110i Card Printer can be used with any Windows 2000 or Windows XP software
application program, using the drivers provided on CD with the printer. Reference Chapter
2 for instructions on installing the P110i printer driver.
Creating a Sample Card
Before you begin a new printing session, print a sample card to ensure that the cards will
be printed correctly. Follow the steps below to print your first card using the True
TM
Colours Card Printer Ribbon Cartridge and the Windows printer driver.
1. Go to the Microsoft Word Software.
2. If the P110i printer was not selected as the default printer, go to File> Select Printer
and choose Zebra P110i Card Printer from the printer names list. Close the Print
dialog box.
3. Go to File>Page Setup.
4. Select the Size tab, and under Paper Size, choose Card. Under orientation, select
Landscape or Portrait.
5. Select the Margins tab, and set the Top, Bottom, Left and Right margins to O (zero).
6. Press OK to close Page Setup window.
7. The card appears on the window.
8. Design a card with both black and colored text and with colored pictures similar to the
sample card shown below.
980515-001 Rev. A
P110i User’s Manual
23
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Operation
Printing
Printing a Sample Card
Once you completed creating your sample card, you are ready to print. Ensure your printer has
TM
a True Colours Card Printer Ribbon Cartridge installed and there is card stock in the card
feeder. Reference Chapter 3 for instructions on installing the ribbon and loading the cards Print
your sample card as follows:.
1. Select File>Print to open the Print dialogue box. Ensure the following settings in the Print
dialogue box:
•
•
•
•
•
•
•
•
•
Printer Name: - Zebra P110i Card Printer
Print to File: - Unchecked
Page Range: - All
Number of Copies: - 1
Collate: - Unchecked
Print What?: - Document
Print: - All pages in range
Pages per sheet: - 1 page
Scale to paper size: - No scaling
2. Click the OK button.
24
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Operation
Printing
3. The printer will feed in a card and start printing. The data download time will vary
depending on the complexity of the card design and the processing speed of the computer.
4. Once the printing is completed, the card is ejected from the printer into the printed card
hopper.
5. Remove the sample card from the card output hopper and check for any discrepancies. If
the sample card is correct, your P110i card printer is to produce more cards.
980515-001 Rev. A
P110i User’s Manual
25
Download from Www.Somanuals.com. All Manuals Search And Download.
P110i Printer Operation
Printing
26
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Cleaning
Cleaning System
Caution • PROTECT YOUR FACTORY WARRANTY!
The recommended maintenance procedures must be performed to maintain your
factory warranty. Other than the recommended cleaning procedures described in
this manual, allow only Zebra authorized technicians to service the P110i Printer.
•NEVER loosen, tighten, adjust, or bend, etc. a part or cable inside the
printer.
•NEVER use a high pressure air compressor to remove particles in the
printer.
SYour P110i Printer includes a simple cleaning system using Pre-Saturated Cleaning
Cards provided. The regular use of these cards will clean and maintain important parts of
your printer that cannot be reached: including Print Head, the Transport Rollers, and the
Magnetic Encoder Station (optional feature).
When to Clean
After approximately 1000 color cards have been printed, the printer LCD will prompt
CLEAN PRINTER, or when print quality has been degraded.
How to Clean
1. Leave power on.
2. Press and hold the Multi-Function Control Button for 5 seconds.
3. When the cleaning cycle is initiated, the LCD message REMOVE RIBBON THEN
CLOSE LID will display.
980515-001 Rev. A
P110i User’s Manual
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
Cleaning System
FEEDER
CLEANING
CARD
CARD
FEEDER
COVER
PRINTER PATH
CLEANING CARD
MULTI-FUNCTION
LCD PANEL
MULTI-FUNCTION
CONTROL BUTTON
4. After the ribbon is removed and the lid is closed, the message EMPTY FEEDER THEN
CLOSE COVER will display.
5. If the lid is opened and closed without removing the ribbon, the REMOVE RIBBON
THEN CLOSE LID message will remain.
6. Once the cover is closed, the firmware will eject any card inside the printer. The message
EJECTING CARD will display.
7. The LCD will then display FEED LONG CLEANING CARD IN EXIT. When the card
sensor registers the presence of the cleaning card, the rollers should take the card into the
printer.
8. When the cleaning process is done, the printer will eject the cleaning card. If the card
sensor still senses the cleaning card, the message REMOVE LONG CLEANING CARD
will display.
9. Once the long cleaning card is no longer sensed by the exit card sensor, the message
INSERT FEEDER CLEANING CARD will display. Open the feeder cover and insert
the feeder cleaning card.
10. When the feeder cleaning card has been sensed by the feeder card sensor, the message
CLOSE FEEDER COVER will display.
11. When feeder cleaning is complete, the message REMOVE FEEDER CLEANING
CARD will display.
12. After the card is removed, the LCD will display READY. You may now reload the ribbon
and cards and continue printing.
28
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
Cleaning the Print Head
Cleaning the Print Head
Use of the cleaning cards will normally do an adequate job of cleaning the printer. However, a
separate Print head cleaning, using swabs, can remove more stubborn deposits when print
anomalies persist. To avoid deposits, only use foam-tipped swabs.
Caution • Never use a sharp object to scrape deposits from the print head.
Permanent damage to the print head will result
1. Place the printer power switch in the OFF (0) position.
2. Open printer lid by pressing cover release button and open cover fully to reveal print head
mounted to inside of cover.
3. Clean Print Head by moving alcohol-moistened swab tip side-to-side across Print Head
elements. Only use moderate force.
4. Allow two to three minutes for the printhead to dry before placing the printer power
switch in the ON ( | ) position.
5. To reorder swabs, reference the P110i Printer Media List.
980515-001 Rev. A
P110i User’s Manual
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning
Cleaning the Print Head
30
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
6
Troubleshooting
Troubleshooting Procedures
This section offers solutions to potential problems you may experience with your P110i
printer.
Print Quality Issues
This section will help you resolve print quality problems The print quality is dependent on
several factors. The two most important factors that will increase your print quality are
cleanliness and card stock. To diagnose and fix print quality problems, follow the
troubleshooting procedures below:
Example • Small spots appear on the printed card with a non-printed area or a different
color.
Possible Cause:
•
Contamination on the card surface
Solutions:
•
•
Check that cards are stored in a dust free
environment
Use a different supply of cards
Possible Cause:
•
•
Cleaning roller not installed
Dust inside the printer and/or dirty Cleaning Roller
Solutions:
•
•
Perform a Cleaning of the printer (reference Chapter 5)
Check that the protective cover was removed from the ribbon cartridge cleaning
roller (reference Chapter 3).
•
If printing one card at a time, replace the cleaning roller located at the front of the
printer (reference Appendix B).
980515-001 Rev. A
P110i User’s Manual
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting Procedures
Example • There are non-printing horizontal lines (white) on the card surfaces.
Possible Cause:
•
Ribbon cartridge is not correctly positioned.
Solutions:
•
Ensure that the ribbon is properly rolled onto the
ribbon cores of the cartridge and that there are no
wrinkles in the ribbon.
•
Replace ribbon cassette.
Possible Cause:
•
Print Head is dirty.
Solutions:
•
Clean the Print Head
Possible Cause:
•
Print Head elements are damaged (e.g. scratched or burnt).
Solutions:
•
Call Zebra Customer Service for Print Head replacement information.
Example • Printing shows very pale or inconsistent results.
Possible Cause:
•
Ribbon cartridge have been stored improperly or is
damaged.
Solution:
•
Change ribbon cartridge and print again.
Possible Cause:
•
Cards may not meet specifications
Solution:
•
Use a different supply of cards.
Possible Cause:
•
Contrast and/or Intensity may be set to values which are too high.
Solution:
•
Adjust Contrast and/or Intensity values in software.
Possible Cause:
•
Dust or embedded contamination on elements of the Print Head.
Solution:
Perform a Cleaning of the Print Head (Reference Chapter 4, Cleaning the Print Head)
•
32
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting Procedures
Example • Printing shows blurry printed image.
Possible Cause:
•
Ribbon cartridge may not be correctly positioned.
Solution:
•
•
Check that the ribbon is properly rolled onto the
ribbon cores of the cartridge, with no wrinkles.
Replace ribbon cartridge, making sure it locks in
place, and print again.
Possible Cause:
Ribbon may not be synchronized on the correct color panel position.
Solution:
•
•
Open lid, then close lid to synchronize ribbon.
Possible Cause:
•
Cards may not meet specifications.
Solution:
•
Use a different supply of cards.
Possible Cause:
•
Dust or embedded contamination inside the printer and/or dirty Cleaning Roller.
Solution:
•
•
Clean the Print Head.
Replace Cleaning Roller
Example • No printing on the card.
Possible Cause:
•
Ribbon cartridge may not be installed in the printer.
Solution:
•
Check for ribbon cartridge in the printer
Possible Cause
•
Cards may not meet specifications.
Solution:
•
Use a different supply of cards
Possible Cause
•
•
Cable on Print Head may be disconnected
Print Head elements may be scratched or burnt.
Solution
•
Call Service for Print Head repair or replacement information.
980515-001 Rev. A
P110i User’s Manual
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Troubleshooting Procedures
34
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Technical Specifications
General
TM
•
•
•
Load-N-Go drop-in ribbon cartridge
16-digit LCD display
Windows® drivers for 2000 and XP
Color Printing
Bar Code
•
•
•
Color dye sublimation or monochrome thermal transfer printing
30 seconds per card full color single sided (YMCKO)
300 dpi (11.8 dots/mm) print resolution
•
•
•
•
Code 39, Code 128 B & C with & without check digit
2 of 5 & 2 of 5 Interleaved
UPC-A, EAN 8 & EAN 13
PDF-417 2D bar code and other symbologies can be printed via
Windows drivers
Cards
•
•
•
•
•
•
•
Types: PVC, PVC Composite, Adhesive backed
Card width/length: ISO CR-80-ISO 7810, 2.12" (54mm) x 3.38" (86mm)
Magnetic Stripe-ISO 7811
Smart Card-ISO 7816
Card thickness: 30 mil (.76mm) (+/- 10%)
Card feeder capacity: 100 cards (30 mil)
Card output hopper capacity: 45 cards (30 mil)
980515-001 Rev. A
P110i User’s Manual
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Ribbons Cartridges
TM
•
Load-N-Go ribbon cartridge with integrated card-cleaning roller
•
•
•
i Series technology featuring contact-chip-based ribbon detection
YMCKO: 200 cards/cartridge
Monochrome: 1000 cards/cartridge in black, blue, or white
Interfaces
•
USB 1.1 (cable included)
Dimensions
•
Width: 7.9 in (201mm)
Depth: 12.9 in (328mm)
Height: 8.5 in (216mm)
Weight: 9.5 lbs (4.3kg)
•
•
•
Electrical
•
110 ~ 240 Volts AC, 50 ~ 60 Hz (auto switching)
16MB image memory standard
•
•
FCC Class B, CE, UL and CUL approved
Environmental
•
Operating Temperature: 60°F to 86°F (15°C to 30°C)
Operating Humidity: 20% to 65% non-condensing
Storage Temperature: 23°F to 158°F (-5°C to 70°C)
Storage Humidity: 20% to 70% non-condensing
Ventilation: Free air
•
•
•
•
Options
•
Magnetic encoder (30 mil cards only), 3 track HiCo/LoCo
TM
•
•
•
CardSense single card-feed mode
P110i Starter Kit (200 cards and 1 YMCKO ribbon)
Cleaning Kit (4 print engine and 4 feeder cleaning cards)
36
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Card Dimensions
Card Dimensions
ISO standard dimensions for plain card
2.125 ± 0.002in
(53.98 ± 0.050mm)
3.375 ± 0.010in
(85.72 ± 0.25mm)
Radius
0.125in
(3.18mm)
0.009 ~ 0.034in
(0.23 ~ 0.84mm)
ISO standard dimensions for magnetic stripe card
0.623in (15.82mm) min
0.218in (5.54mm) max
MAGNETIC STRIPE
0~0.115 in (2.92 mm)
0~0.115in (2.92mm)
980515-001 Rev. A
P110i User’s Manual
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
Card Dimensions
38
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix A
Magnetic Card Encoder
Magnetic Card Stripe Encoder
This section contains information on the additional operations of the P110i Printers with
Magnetic Card Stripe Encoder.
Introduction
Operation and maintenance requirements for the P110i Printer with the optional magnetic
card stripe encoder. The magnetic encoder can be set for either high or low coercivity.
980515-001 Rev. A
P110i User’s Manual
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnetic Card Encoder
Introduction
Media Loading Orientation
Caution • ONLY USE cards that comply with ISO 7810 & 7811 standards for
magnetic stripe cards. The magnetic stripe must be flush to the surface of the card
to work properly. Never use cards which have taped-on magnetic stripes.
The magnetic encoder is a factory installed item with the read/write head positioned below or
above the card path, available with HICO or LOCO encoding.
When loading cards with magnetic stripes into the card feeder, please ensure that the magnetic
stripe is facing the left side of the printer, and closest to the bottom edge of the card feeder, as
shown below.
MAGNETIC
STRIPE
Note • Zebra approved HICO & LOCO PVC cards are available. (Reference P110i printer Media
List.)
Magnetic Encoder Cleaning
Use the standard cleaning card process as described in Chapter 4. This cleans the most
important parts of the printer; including the print Head, Transport Roller and Magnetic Stripe
Encoder.
40
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnetic Card Encoder
Introduction
ISO Standard Encoding
Field
Separator
Track
Density
Valid
Characters
# of
characters
Track #
1
^
210 BPI*
Alphanumeri
c (ASCII
79‡
20~95†)
2
=
=
75 BPI*
Numeric
40‡
(ASCII
48~62)
3
210 BPI*
Numeric
107‡
(ASCII
48~62)
*Bits per inch
†Except the “?” character
‡Including Start, Stop, and LRC characters. Also note that these 3
characters areautomatically managed by the magnetic encoder according
to the ISO Standard Norms.
Note • Refer to the Card Printer Programmer’s Manual for complete programming
information.
980515-001 Rev. A
P110i User’s Manual
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Magnetic Card Encoder
Introduction
42
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix B
TM
Card Sense Single Card
Feed Mode
Printing a Single Card Without Using the Feeder
For operating the P110i card printer in single card feed mode, the printer requires that the
TM
operator install an optional Card Sense Single Card Feed Kit. In Single Card Feed Mode,
the printer will only accept cards through the front slot, not from the card feeder.
TM
Install Card Sense Single Card Feed Kit
POWER
SWITCH
1. Set printer to OFF
980515-001 Rev. A
P110i User’s Manual
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Card SenseTM Single Card Feed Mode
Printing a Single Card Without Using the Feeder
RIBBON
CARTIRDGE
PRINTER
LID
2. Open the lid and remove the ribbon cartridge.
Important • Make sure the output hopper remains closed.
ROLLER FROM
SINGLE CARD FEED KIT
BLUE
TABS
3. Install the black roller from the Single Card Feed Kit into the blue tabs at the front of the
printer, and press roller down firmly to lock into the tabs.
Install Card Cleaning Cartridge
Install the Card Cleaning Cartridge as follows:
BLUE TAPE
CARD
CLEANING
CARTRIDGE
1. Open the lid of the card cleaning cartridge.
44
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Card SenseTM Single Card Feed Mode
Printing a Single Card Without Using the Feeder
2. Insert the cleaning roller into the card cleaning cartridge and close the cartridge.
3. Peel protective wrapper from adhesive cleaning roller by gently pulling on the blue tape,
and discard the wrapper.
4. Slide the Card Cleaning Cartridge into the slots provided at the front of the printer. An
alignment tab is located on the left side of the Card Cleaning Cartridge to ensure proper
installation.
RIBBON
CARTRIDGE
5. Insert the ribbon cartridge with the cleaning roller facing down, so the gears on the ends of
the rollers fit into the appropriate slots.
6. Close the printer lid and push down until you hear an audible click. If you can not close
the lid, the cleaning cartridge or the ribbon cartridge may be installed wrong.
980515-001 Rev. A
P110i User’s Manual
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Card SenseTM Single Card Feed Mode
Printing a Single Card
Setting Up the Printer Driver
1. Go to Printer Properties
2. Select the Device Settings tab
3. Select Single Feed Properties
4. Select Enable Single Feed Support
5. Click the Apply button.
Important • You can disable Single Feed Support and return to printing cards from the
hopper. You do not have to remove the components of the Single Card Feed Kit in order to
operate in normal mode.
Printing a Single Card
1. Place the printer power switch in the ON ( | ) position.
INSERT CARD
2. Insert a single card into the slot at the front of the printer, directly above the card output
hopper. Do not feed more than one card at a time. Printer will take the card.
46
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
Appendix C
Worldwide Sales & Support
Sales and Support Locations
The Americas:
Zebra Technologies, LLC
Card Printer Solutions Headquarters
1001 Flynn Road
Camarillo, CA 93012-8706 USA
Phone: + 1 (805) 579 1800
Fax: + 1 (805) 579 1808
Toll free in US: (800) 452-4056
Europe:
Zebra Technologies Europe Limited
Zebra House
The Valley Centre, Gordon Road
High Wycombe
Buckinghamshire HP13 6EQ, UK
Phone: + 44 (0) 870 241 1527
Fax: + 44 (0) 870 241 0765
e-mail: [email protected]
980515-001 Rev. A
P110i User’s Manual
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Worldwide Sales & Support
Website
Latin America Sales Office:
9800 NW 41st Street, Suite 220
Doral, FL 33178 USA
Phone: + 1 (305) 558 3100
Fax: + 1 (305) 558-8485
Asia Pacific:
Zebra Technologies Asia Pacific, LLC
16 New Industrial Road
#05-03 Hudson TechnoCentre
Singapore 536204
Phone: + 65 6858 0722
Fax: + 65 6885 0836
e-mail: [email protected]
Website
48
P110i User’s Manual
980515-001 Rev. A
Download from Www.Somanuals.com. All Manuals Search And Download.
|