Zanussi Washer ZWF 14380 S User Manual

User  
manual  
Washing  
Machine  
ZWF 14380 W  
ZWF 14380 S  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Safety information  
In the interest of your safety and to ensure  
the correct use, before installing and first  
using the appliance, read this user manual  
carefully, including its hints and warnings.  
To avoid unnecessary mistakes and  
accidents, it is important to ensure that all  
people using the appliance are thoroughly  
familiar with its operation and safety  
features. Save these instructions and make  
sure that they remain with the appliance if it  
is moved or sold, so that everyone using it  
through its life will be properly informed on  
appliance use and safety.  
Always unplug the appliance and turn off the  
water supply after use, cleaning and  
maintenance.  
Under no circumstances should you attempt  
to repair the machine yourself. Repairs  
carried out by inexperienced persons may  
cause injury or serious malfunctioning.  
Contact your local Service Centre. Always  
insist on genuine spare parts.  
Installation  
This appliance is heavy. Care should be  
taken when moving it.  
When unpacking the appliance, check that it  
is not damaged. If in doubt, do not use it and  
contact the Service Centre.  
All packing and transit bolts must be  
removed before use. Serious damage can  
occur to the product and to property if this is  
not adhered to. See relevant section in the  
user manual.  
After having installed the appliance, check  
that it is not standing on the inlet and drain  
hose and the worktop is not pressing the  
electrical supply cable.  
If the machine is situated on a carpeted floor,  
please adjust the feet in order to allow air to  
circulate freely under the appliance.  
Always be sure, that there is no water  
leakage from hoses and their connections  
after the installation.  
General safety  
It is dangerous to alter the specifications or  
attempt to modify this product in any way.  
During high temperature wash programmes  
the door glass may get hot. Do not touch it!  
Make sure that small pets do not climb into  
the drum. To avoid this, please check into  
the drum before using.  
Any objects such as coins, safety pins, nails,  
screws, stones or any other hard, sharp  
material can cause extensive damage and  
must not be placed into the machine.  
Only use the advised quantities of fabric  
softener and detergent. Damage to the fabric  
can ensue if you over-fill. Refer to the  
manufacturer’s recommendations of  
quantities.  
Wash small items such as socks, laces,  
washable belts etc in a washing bag or  
pillow case as it is possible for such items to  
slip down between the tub and the inner  
drum.  
Do not use your washing machine to wash  
articles with whalebones, material without  
hems or torn material.  
If the appliance is installed in a location  
subject to frost, please read the «dangers of  
freezing» chapter.  
Any plumbing work required to install this  
appliance should be carried out by a  
qualified plumber or competent person.  
Any electrical work required to install this  
appliance should be carried out by a  
qualified electrician or competent person.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
3
Make sure that children or pets do not climb  
into the drum. To prevent children or pets  
becoming trapped inside the drum, the  
machine incorporates special feature.  
Use  
This appliance is designed for domestic use.  
It must not be used for purposes other than  
those for which it was designed.  
Only wash fabrics which are designed to be  
machine washed. Follow the instructions on  
each garment label.  
Do not overload the appliance. See the  
relevant section in the user manual.  
Before washing, ensure that all pockets are  
empty and buttons and zips are fastened.  
Avoid washing frayed or torn articles and  
treat stains such as paint, ink, rust, and  
grass before washing. Underwired bras must  
NOT be machine washed.  
Garments which have been in contact with  
volatile petroleum products should not be  
machine washed. If volatile cleaning fluids  
are used, care should be taken to ensure  
that the fluid is removed from the garment  
before placing in the machine.  
To activate this device, To disable this device  
rotate the button  
and restore the  
(without pressing it)  
inside the door  
possibility of closing the  
door, rotate the button  
anti-clockwise until the  
groove is vertical.  
clockwise until the  
groove is horizontal. If  
necessary use a coin.  
Never pull the power supply cable to remove  
the plug from the socket; always take hold of  
the plug itself.  
Never use the washing machine if the power  
supply cable, the control panel, the working  
surface or the base are damaged so that the  
inside of the washing machine is accessible.  
Child safety  
This washing machine is not intended for  
use by young children or infirm persons  
without supervision.  
Young children should be supervised to  
ensure that they do not play with the  
appliance.  
The packaging components (e.g. plastic film,  
polystyrene) can be dangerous to children -  
danger of suffocation! Keep them out of  
children’s reach  
Keep all detergents in a safe place out of  
children’s reach.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4
Description of the appliance  
1
Detergent dispenser drawer  
1
2
2
Control panel  
3
Door opening handle  
4
Drain pump  
5
Adjustable feet  
3
4
5
Detergent dispenser drawer  
Prewash  
Wash  
Fabric Softener  
Download from Www.Somanuals.com. All Manuals Search And Download.  
5
Control panel and functions  
8
1
2
3
4
5
6
7
The programme selector dial allows you to select a programme  
and/or to switch the machine on/off. It can be turned either  
Programme selector dial and  
On/Off switch  
1
2
6
clockwise or anticlockwise. The light of button  
starts to flash.  
Press this button repeatedly to change the spin speed, if you  
want your laundry to be spun at a speed different from the one  
proposed by the washing machine or to select the Night Cycle  
Spin reduction button  
and Rinse Hold  
. The relevant light will light up.  
By pressing this button, you can select only one of the following  
option: Prewash, Intensive, Super Quick (see the relevant  
chapter «Operating sequence»). The relevant light will light up.  
Options button  
3
4
By pressing this button, the machine performs some additional  
rinses.  
Extra Rinse button  
The display shows the following information: duration of the  
selected programme, delayed start, incorrect option selection,  
alarm codes, child lock activated, heating phase and end of  
programme.  
Display  
5
6
This button allows you to start the selected programme; the  
corresponding green pilot light stops flashing.  
It also interrupts a programme which is running, the  
corresponding green pilot light starts to flash.  
Start/Pause button  
By pressing this button the wash programme can be delayed  
from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to  
a maximum of 20 hours.  
Delay Start button  
Indicator lights  
7
8
The different pilot lights illuminate depending on the running  
programme phase:  
Download from Www.Somanuals.com. All Manuals Search And Download.  
6
Programme table  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
Main wash, rinses  
Long spin at the max  
speed  
Max load: 7 kg  
*Reduced Load: 3.5 kg  
Spin red.  
Cottons  
95°  
White cotton (normally  
soiled cotton items).  
Prewash, Intensive,  
Super Quick, Extra rinse  
White and fast  
coloured cotton  
(normally soiled cotton  
items)  
Main wash, rinses  
Long spin at the max  
speed  
Cottons  
60° Eco  
Spin red.  
Prewash, Extra rinse  
Max load: 7 kg  
Main wash, rinses, long  
spin at the max speed  
Max load: 7 kg  
*Reduced Load: 3.5 kg  
Spin red.  
Cottons  
60° - 40°  
Coloured cotton lightly  
soiled  
Prewash, Intensive,  
S. Quick, Extra rinse  
Main wash, rinses  
Long spin at the max  
speed  
Cottons  
40° Eco  
Coloured cotton lightly  
soiled  
Spin red.  
Prewash, Extra rinse  
Max load: 7 kg  
Main wash  
rinses  
Short spin 900 rpm  
Max load: 3.5 kg  
*Reduced Load: 1.5 kg  
Spin red.  
Synthetics  
50° - 40°  
Synthetic or mixed  
fabrics  
Prewash, Intensive,  
Super Quick  
Extra rinse  
Main wash  
rinses  
Short spin 900 rpm  
Max load: 1 kg  
Synthetic or mixed  
fabrics to be gently  
washed and spun.  
Synthetics  
Easy iron 40°  
Spin red.  
Prewash, Extra rinse  
Main wash,  
rinses  
Short spin 700 rpm  
Max load: 3.5 kg  
*Reduced Load: 1.5 kg  
Delicates  
40° - 30°  
Delicate fabrics, for  
example curtains.  
Prewash, Super Quick  
Intensive, Extra Rinse  
* If you select the SUPER QUICK option by pressing the relevant button, we recommend you, to  
reduce the maximum load as indicated in the table above. Full loading is possible however with  
somewhat reduced cleaning results.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Programme table  
Programme/  
Temperature  
Description of  
programme  
Type of laundry  
Options  
Programme for wool  
«Pure new wool, non-  
shrink, machine  
Main wash  
rinses  
Short spin 900 rpm  
Max load: 2 kg  
Wool  
40°  
Spin red.,  
,
,
washable» label.  
Main wash, rinses  
Short spin 900 rpm,  
Max load: 2 kg  
Handwash  
30° - Cold  
Special programme for  
hand washing fabrics  
Spin red.,  
Main Wash, rinses  
Short spin 700 rpm  
Max load: 2 kg  
Mini 30’  
30°  
Short cycle for lightly  
soiled fabrics  
Main wash, rinses  
Short spin 700 rpm  
Max load: 1 kg  
Silk  
30°  
Silk items to be gentle  
washed and spun.  
,
Main Wash, rinses  
Short spin 900 rpm  
Max load: 1 pair  
Sport  
Short cycle for 1 pair of  
sport shoes  
Spin Red.  
Shoes 40°  
Prewash, Extra rinse  
Prewash at 30°C  
Main wash, rinses  
Short spin 900 rpm,  
Max load: 2.5 kg  
Spin red.,  
,
Programme for heavily  
soiled synthetics items  
Sport 40°  
Rinse  
Extra rinse  
rinses  
Long spin at the max  
speed  
Separate rinse cycle for  
hand washed items of  
cotton.  
Spin red.  
Extra rinse  
Max load: 7 kg  
For emptying out the last  
rinse water in  
programmes with the  
Rinse Hold or Night  
Cycle option.  
Drain  
Spin  
Draining of water  
Drain and long spin at the  
max speed  
Separate spin for  
cottons.  
Spin red.  
Max load: 7 kg  
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Programme information  
This programme can be selected for slightly or normally soiled  
cotton items. The temperature will decrease and the washing time  
will be extended. This allows you to obtain a good washing  
efficiency whilst saving energy.  
Cottons Eco  
Washing programme for machine washable wool as well as for hand  
washable woollens and delicate fabrics with the «hand washing»  
Wool and  
care symbol  
.
Note: A single or bulky item may cause imbalance. If the appliance  
doesn’t perform the final spin phase, add more items, redistribute  
the load manually and then select the spinning programme.  
Handwash  
By selecting this programme, the laundry is gently washed and spun  
to avoid any creasing. In this way ironing is easier. Furthermore the  
machine will perform additional rinses.  
Easy Iron  
Rinse  
With this programme it is possible to rinse and spin cotton garments  
which have been washed by hand.  
The machine performs 3 rinses, followed by a final spin at maximum  
speed. The spin speed can be reduced by pressing the relevant  
button.  
For emptying out the water of the last rinse in programmes with the  
Rinse Hold or Night Cycle option.  
Firstly, turn the programme selector dial to «Off», then select  
Drain  
6
programme Drain and press the button  
.
Separate spin for hand washed garments and after programmes  
with Rinse Hold or Night Cycle option. Before selecting this  
programme the selector dial must be turned to «Off». You can  
choose the speed by pressing the relevant button to adapt it to the  
fabrics to be spun.  
Spin  
With this programme it is possible to wash one pair of sport shoes.  
The shoes would be gently washed and spun. Washing temperature  
40°C. Note! Do not wash your sport shoes together with laundry.  
Sport shoes 40°  
This programme is suitable for washing heavily soiled sport items of  
synthetic fabrics. The machine will automatically add a prewash  
phase before the main wash to eliminate mud stains.  
Sport 40°  
Note ! We recommend that you do not put the detergent into the  
compartment  
reduced.  
of the detergent drawer. The spin speed is  
To reset a programme and to switch off the machine turn the  
selector dial to «Off».A new programme can now be selected.  
Off = Cancelling  
Download from Www.Somanuals.com. All Manuals Search And Download.  
9
Washing hints  
Sorting the laundry  
Maximum loads  
Follow the wash code symbols on each  
Recommended loads are indicated in the  
programme charts.  
garment label and the manufacturer’s washing  
instructions. Sort the laundry as follows: whites,  
coloureds, synthetics, delicates, woollens.  
General rules:  
Cotton, linen: drum full but not too tightly  
packed;  
Temperatures  
Synthetics: drum no more than half full;  
Delicate fabrics and woollens: drum no more  
than one third full.  
Washing a maximum load makes the most  
efficient use of water and energy.  
For heavily soiled laundry, reduce the load  
size.  
for normally soiled white cottons  
90° or 95°  
50°/60°  
and linen (e.g. tea cloths, towels,  
tablecloths, sheets...)  
for normally soiled, colour fast  
garments (e.g. shirts, night  
dresses, pyjamas....) in linen,  
cotton or synthetic fibres and for  
lightly soiled white cotton (e.g.  
underwear).  
Laundry weights  
The following weights are indicative:  
for delicate items (e.g. net  
curtains), mixed laundry including  
30°-40°-Cold synthetic fibres and woollens  
bearing the label «pure new wool,  
bathrobe  
napkin  
quilt cover  
sheet  
pillow case  
tablecloth  
1200 g  
100 g  
700 g  
500 g  
200 g  
250 g  
200 g  
100 g  
200 g  
100 g  
600 g  
200 g  
500 g  
100 g  
100 g  
machine washable, non-shrink».  
Before loading the laundry  
Never wash whites and coloureds together.  
Whites may lose their «whiteness» in the  
wash.  
New coloured items may run in the first wash;  
they should therefore be washed separately  
the first time.  
Make sure that no metal objects are left in  
the laundry (e.g. hair clips, safety pins,  
pins). Button up pillowcases, close zip  
fasteners, hooks and poppers. Tie any belts  
or long tapes.  
towelling towel  
tea cloth  
night dress  
ladies’ briefs  
man’s work shirt  
man’s shirt  
man’s pyjamas  
blouse  
men’s underpants  
Remove persistent stains before washing.  
Rub particularly soiled areas with a special  
detergent or detergent paste.  
Treat curtains with special care. Remove hooks  
or tie them up in a bag or net.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
10  
Removing stains  
Detergents and additives  
Stubborn stains may not be removed by just  
Good washing results also depend on the  
water and detergent. It is therefore advisable to choice of detergent and use of the correct  
treat them prior to washing.  
quantities to avoid waste and protect the  
environment. Although biodegradable,  
detergents contain substances which, in large  
quantities, can upset the delicate balance of  
nature.  
The choice of detergent will depend on the  
type of fabric (delicates, woollens, cottons,  
etc.), the colour, washing temperature and  
degree of soiling.  
Blood: treat fresh stains with cold water. For  
dried stains, soak overnight in water with a  
special detergent then rub in the soap and  
water.  
Oil based paint: moisten with benzine stain  
remover, lay the garment on a soft cloth and  
dab the stain; treat several times.  
Dried grease stains: moisten with turpentine,  
lay the garment on a soft surface and dab the  
stain with the fingertips and a cotton cloth.  
All commonly available washing machine  
detergents may be used in this appliance:  
powder detergents for all types of fabric,  
powder detergents for delicate fabrics (60°C  
max) and woollens,  
liquid detergents, preferably for low  
temperature wash programmes (60°C max)  
for all types of fabric, or special for woollens  
only.  
Rust: oxalic acid dissolved in hot water or a  
rust removing product used cold. Be careful  
with rust stains which are not recent since the  
cellulose structure will have already been  
damaged and the fabric tends to hole.  
Mould stains: treat with bleach, rinse well  
(whites and fast coloureds only).  
The detergent and any additives must be  
placed in the appropriate compartments of the  
dispenser drawer before starting the wash  
programme.  
If using concentrated powder or liquid  
detergents, a programme without prewash  
must be selected.  
The washing machine incorporates a  
recirculation system which allows an optimal  
use of the concentrated detergent.  
Pour liquid detergent into the dispenser drawer  
Grass: soap lightly and treat with bleach  
(whites and fast coloureds only).  
Ball point pen and glue: moisten with  
acetone (*), lay the garment on a soft cloth and  
dab the stain.  
Lipstick: moisten with acetone as above, then  
treat stains with methylated spirits. Remove  
any residual marks from white fabrics with  
bleach.  
Red wine: soak in water and detergent, rinse  
and treat with acetic or citric acid, then rinse.  
Treat any residual marks with bleach.  
compartment marked  
the programme.  
just before starting  
Any fabric softener or starching additives must  
be poured into the compartment marked  
before starting the wash programme.  
Follow the product manufacturer’s  
recommendations on quantities to use and do  
not exceed the «MAX» mark in the  
detergent dispenser drawer.  
Ink: depending on the type of ink, moisten the  
fabric first with acetone (*), then with acetic  
acid; treat any residual marks on white fabrics  
with bleach and then rinse thoroughly.  
Tar stains: first treat with stain remover,  
methylated spirits or benzine, then rub with  
detergent paste.  
(*) do not use acetone on artificial silk.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
11  
Quantity of detergent to be used  
Degrees  
Level Characteristic  
The type and quantity of detergent will depend  
on the type of fabric, load size, degree of  
soiling and hardness of the water used.  
Water hardness is classified in so-called  
«degrees» of hardness. Information on  
hardness of the water in your area can be  
obtained from the relevant water supply  
company, or from your local authority.  
Follow the product manufacturers’ instructions  
on quantities to use.  
German  
°dH  
French  
°T.H.  
1
2
3
4
soft  
medium  
hard  
0-7  
0-15  
16-25  
26-37  
> 37  
8-14  
15-21  
> 21  
very hard  
Degrees of water hardness  
Follow the product manufacturers’ instructions  
on quantities to use.  
Use less detergent if:  
you are washing a small load,  
the laundry is lightly soiled,  
large amounts of foam form during washing.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
12  
Before the first use  
Child safety lock  
WARNING!  
This device function allows you to leave the  
appliance unattended without having the worry  
that children might be injured by or cause  
damage to the appliance.  
Ensure that the electrical and water  
connections comply with the installation  
instructions.  
This function remains enabled also when the  
washing machine is not working.  
IMPORTANT!  
Remove the polystyrene block and any  
material from the drum.  
There are two different ways to set this option:  
before pressing the button 6 : it will be  
impossible to start the machine.  
after pressing the button 6 : it will be  
impossible to change any other programme  
or option.  
IMPORTANT!  
Before the first wash run a cotton cycle at  
95°C or 90°C, without any laundry in the  
machine, to remove any manufacturing residue  
from the drum and tub. Pour 1/2 a measure of  
detergent into the dispenser drawer and start  
the machine.  
To enable (or disable) this option press  
simultaneously for about 6 seconds the buttons  
3 and 4 until the paddle icon  
appears  
Acoustic signals  
(disappears) on (from) the display .  
The machine is provided with an acoustic  
device, which sounds in the following cases:  
Stand by mode  
If your laundry is not removed within 10  
minutes after the programme is finished, the  
backlight of the display switches off and the  
energy saving system will be enabled.  
Only the pilot light of the button  
to indicate that you must switch the appliance  
at the end of the cycle  
if there is a fault  
By pressing buttons 2 and 3  
simultaneously for about 6 seconds,the  
acoustic signal is deactivated (except if there is  
a fault). By pressing these 2 buttons again, the  
acoustic signal is reactivated.  
6
still blinks  
off.  
If you press any button, the appliance will  
come out from the energy saving status and  
you could set another washing programme or  
switch the appliance off.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
13  
Operating sequence  
IMPORTANT!  
If you turn the programme selector dial to  
another programme when the machine is  
Load the laundry  
Open the door by  
carefully pulling the  
door handle outwards.  
Place the laundry in the  
drum, one item at a  
time, shaking them out  
6
working, the red pilot light of button  
will  
flash 3 times and the message Err is displayed  
to indicate a wrong selection. The machine will  
not perform the new selected programme.  
Select the spin speed or Night Cycle or  
Rinse Hold option by pressing the button  
2
When selecting a programme, the light  
corresponding to the maximum speed allowed  
for that programme will illuminate (refer to the  
section «Programme table» for the maximum  
allowed by each cycle spin speed).  
as much as possible. Close the door.  
Measure out the detergent and the fabric  
softener  
Press this button repeatedly to change the spin  
speed, if you want your laundry to be spun at a  
speed different from the one proposed by the  
appliance.  
Pull out the dispenser drawer until it stops.  
Measure out the amount of detergent required,  
pour it into the main wash compartment  
and, if you wish to carry out a programme with  
the prewash phase, pour it into the  
Night Cycle  
: by selecting this option, the  
machine will not drain the water of the last  
rinse, so as not to crease the laundry. As all  
spinning phases are suppressed, this washing  
cycle is very quiet and it can be selected at  
night or in times with a more economical power  
rate. On some programmes, the rinses will be  
performed with more water.  
When the programme has finished, the display  
shows a flashing zero «0.00» but the door  
remains locked to indicate that the water must  
be emptied out.  
compartment marked  
.
If required, pour fabric softener into the  
compartment marked  
(the amount used  
must not exceed the «MAX» mark in the  
drawer). Close the drawer gently.  
Select the required programme by turning  
1
the programme selector dial (  
)
6
The green light of the button  
starts to flash.  
Rinse Hold  
: by selecting this option the  
The selector dial can be turned either  
clockwise or anticlockwise.  
water of the last rinse is not emptied out to  
prevent the fabrics from creasing.  
When the programme has finished, the display  
shows a flashing zero «0.00» but the door  
remains locked to indicate that the water must  
be emptied out.  
Turn to position «Off» to Reset programme /  
Switch OFF of the machine.  
At the end of the programme the selector  
dial must be turned to position «Off», to  
switch the machine off.  
To empty out the water, see the paragraph  
«At the end of the cycle».  
Download from Www.Somanuals.com. All Manuals Search And Download.  
14  
Operating sequence  
Select the desired option by pressing the  
After the programme  
has started, the time  
remaining is updated  
every minute.  
3
button  
Press this button repeatedly, to select one of  
the available options. The relevant light will  
light up.  
2.05  
Prewash: select this option if you wish your  
laundry to be prewashed at 30°C before the  
main wash. The prewash ends with a short  
spin in programmes for cotton and synthetic  
fabrics, whereas in the programmes for  
delicate fabrics the water is only drained.  
Delayed start  
The selected delay (20 hours max) set by  
pressing the relevant button appears on the  
display for about 3 seconds, then the duration  
of the previously selected programme is  
displayed.  
Intensive: this option can be selected for  
heavily soiled laundry: the washing intensity  
will be increased and the washing time will be  
prolonged by a few minutes depending on the  
selected type of fabric.  
The delay time value  
decreases by one unit  
every hour and then,  
when 1 hour remains,  
the time decreases  
15 h  
Super Quick: a very short cycle for slightly  
soiled items that have been used or worn for a  
short time.  
The washing time will be reduced according to  
the type of fabric and the selected temperature.  
We recommended that you to reduce the  
laundry load (see the programmes table).  
every minute.  
Incorrect option selection  
If an option which is not  
compatible with the set  
wash programme is  
selected, the message  
Select the Extra Rinse option by pressing  
the button  
The machine performs some additional rinses.  
This option is recommended for people who  
are allergic to detergents, and in areas where  
the water is very soft.  
Err is displayed for a  
few seconds and the red  
starts flashing.  
4
6
light of the button  
Alarm codes  
In the event of operating  
problems, some alarm  
codes can be displayed,  
for example E20 (see  
paragraph “What do  
if...”).  
Display ( 5 )  
E20  
The display shows the following information:  
Duration of the selected programme  
After selecting a programme, the duration is  
displayed in hours and minutes (for example  
2 .05 ). The duration is calculated automatically  
on the basis of the maximum recommended  
load for each type of fabric.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
15  
Operating sequence  
Heating phase  
Selecting the delayed start:  
Select the programme and the required  
options.  
Select the delay start by pressing the button  
7 .  
Press the button 6 : the machine starts its  
countdown.  
During the washing  
cycle the display shows  
a temperature icon to  
indicate that the  
2.05  
appliance has started  
the heating phase of the water in the tub.  
The programme will start after the selected  
delay has expired.  
Start the programme by pressing the button  
6
Cancelling the delayed start:  
You can cancel the delay time at any moment,  
before you press the button 6 .  
If you have already pressed it, and you wish to  
cancel the delay time, proceed as follows:  
To start the selected programme, press this  
button; the corresponding green pilot light  
stops flashing.  
The «Wash» and «Door» lights illuminate to  
indicate that the appliance starts operating and  
the door is locked.  
• set the washing machine to PAUSE by  
pressing the button 6 ;  
To interrupt a programme which is running,  
• press the button 7 repeatedly until the  
symbol 0’ is displayed.  
6
press the button  
: the corresponding green  
pilot light starts to flash. To restart the  
programme from the point at which it was  
interrupted, press this button again.  
If you have chosen a delayed start, the  
machine will begin the countdown.  
• press the button 6 again to start the  
programme.  
IMPORTANT!  
• The selected delay can be changed only  
after selecting the washing programme  
again.  
• The door will be locked throughout the delay  
time. If you need to open the door, you must  
first set the washing machine to PAUSE by  
pressing the button 6 and then wait a few  
minutes until the «Door» light has gone off.  
After you have closed the door, press the  
button 6 again.  
IMPORTANT!  
If an incorrect option is selected, the red pilot  
light of this button flashes 3 times and the  
message Err is displayed for a few seconds.  
Select the Delay Start by pressing the  
7
button  
Before you start the programme, if you wish to  
delay the start, press the button 7 repeatedly,  
to select the desired delay.  
The selected delay time value (up to 20 hours)  
will appear on the display for a few seconds,  
then the duration of the programme will appear  
again.  
The Delay Start cannot be selected with  
Drain programme.  
Indicator lights ( 8 )  
After having pressed the button 6 , the  
«Wash» pilot light illuminates and stays on  
while the machine is working. At the end of  
any cycle it goes off.  
You must select this option after you have set  
the programme and before you press the  
button 6 .  
Download from Www.Somanuals.com. All Manuals Search And Download.  
16  
Operating sequence  
When the programme has finished, the «End»  
pilot light illuminates and at the same time the  
light of the button 6 goes off. If there is water  
left in the tub, the «Door» light illuminates: the  
door remains locked.  
The «Door» pilot light indicates if the door can  
be opened:  
• light on: the door cannot be opened.  
The appliance is operating or there is water  
left in the tub. Attention! If the door is locked  
do not try to open it!  
Opening the door after the programme has  
started  
First set the machine to pause by pressing the  
button 6 .  
If the «Door» light flashes after a few minutes  
the door can be opened. If this light remains lit,  
this means that the machine is already heating  
or that the water level is too high.  
In this case the door can not be opened.  
If you cannot open the door but you need to  
open it you have to switch the machine off by  
turning the selector dial to «Off». After about a  
few minutes the door can be opened (pay  
attention to the water level and  
• light off: the door can be opened.  
The washing programme is finished.  
• flashing light: the door is opening.  
temperature!).  
Altering an option or a running programme  
It is possible to change a few options before  
the programme carries them out.  
After this procedure, it will be necessary to set  
the programme and the options again and then  
to press button 6 .  
Before you make any change, you must pause  
the washing machine by pressing the button  
At the end of the programme  
6
The machine stops automatically. On the  
display will appear a flashing «0.00» and the  
door can be opened.  
If the «Rinse hold» or «Night Cycle» option has  
been selected, the display will show a flashing  
«0.00» and the door remains locked to  
indicate that the water must be emptied out  
before opening the door.  
.
Changing a running programme is possible  
only by resetting it. Turn the programme  
selector dial to «Off» and then to the new  
programme position. Start the new programme  
by pressing the button 6 again.  
The washing water in the tub will not be  
emptied out.  
Interrupting a programme  
To empty out the water proceed as follows:  
Press the button 6 to interrupt a programme  
which is running, the corresponding light starts  
to flash. Press this button again to restart the  
programme.  
1.turn the programme selector dial to «Off»  
2.select the Drain or Spin programme  
3.reduce the spin speed if needed, by pressing  
the relevant button  
Cancelling a programme  
4.press the button 6  
to start the selected  
Turn the selector dial to Off to cancel a  
programme which is running. You can now  
select a new programme.  
programme  
5.at the end of programme, only the «End»  
light illuminates. Now it is possible to open  
the door.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
17  
Turn the programme selector dial to «Off» to  
switch the machine off.  
Remove the laundry from the drum and  
carefully check that the drum is empty.  
If you do not intend to carry out another wash,  
close the water tap. Leave the door open to  
prevent the formation of mildew and  
unpleasant smells.  
Care and cleaning  
IMPORTANT!  
External cleaning  
You must DISCONNECT the appliance from  
the electricity supply, before you can carry out  
any cleaning or maintenance work.  
Clean the exterior cabinet of the appliance with  
soap and water only, and then dry thoroughly.  
Cleaning the dispenser drawer  
The washing powder and additive dispenser  
drawer should be cleaned regularly.  
Descaling  
The water we use normally contains lime. It is  
a good idea to periodically use a water  
softening powder in the machine. Do this  
separately from any laundry washing, and  
according to the softening powder  
manufacturer's instructions. This will help to  
prevent the formation of lime deposits.  
Maintenance Wash  
With the use of low temperature washes it is  
possible to get a build up of residues inside the  
drum.  
We recommend that a maintenance wash be  
performed on a regular basis.  
To aid cleaning, the top part of the additive  
compartment should be removed.  
Remove the drawer by pressing the catch  
downwards and by pulling it out. Flush it out  
under a tap, to remove any traces of  
accumulated powder.  
To run a maintenance wash:  
The drum should be empty of laundry.  
Select the hottest cotton wash programme.  
Use a normal measure of detergent, must be  
a powder with biological properties.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
18  
Cleaning the drawer recess  
Having removed the  
Remove any objects from the pump impeller  
by rotating it.  
Refit the cap on the emergency emptying  
hose and place the latter back in its seat.  
drawer, use a small  
brush to clean the  
recess, ensuring that all  
washing powder  
residue is removed from  
the upper and lower  
Screw the pump cover  
fully in.  
Close the pump door.  
part of the recess.  
Replace the drawer and run the rinse  
programme without any clothes in the drum.  
I
Cleaning the pump  
The pump should be inspected if  
MPORTANT!  
When the appliance is in use and depending  
on the programme selected there can be hot  
water in the pump.  
Never remove the pump cover during a wash  
cycle, always wait until the appliance has  
finished the cycle, and is empty. When  
replacing the cover, ensure it is securely  
retightened so as to stop leaks and young  
children being able to remove it.  
the machine does not empty and/or spin  
the machine makes an unusual noise during  
draining due to objects such as safety pins,  
coins etc. blocking the pump.  
Proceed as follows:  
Disconnect the appliance.  
If necessary wait until the water has cooled  
down.  
Open the pump door.  
Cleaning the water inlet filter  
If your water is very hard or contains traces of  
lime deposit, the water inlet filter may become  
clogged.  
It is therefore a good idea to clean it from time  
to time.  
Place a container close  
to the pump to collect  
any spillage.  
Pull out the emergency  
emptying hose, place it  
in the container and  
remove its cap.  
Turn off the water tap.  
Unscrew the water inlet  
hose. Clean the filter  
using a hard bristle  
brush. Refit the inlet  
When no more water comes out, unscrew the  
pump cover and remove it. Always keep a  
rag nearby to dry up spillage of water when  
removing the cover.  
hose.  
The dangers of freezing  
If the machine is exposed to temperatures  
below 0°C, certain precautions should be  
taken.  
Turn off the water tap.  
Unscrew the inlet hose.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
19  
Place the end of the emergency emptying  
hose and that of the inlet hose in a bowl  
placed on the floor and let water drain out.  
Screw the water inlet hose back on and  
reposition the emergency emptying hose  
after having put the cap on again.  
When you intend to start the machine up  
again, make sure that the room temperature  
is above 0°C.  
Emergency emptying out  
If the water is not discharged, proceed as  
follows to empty out the machine:  
pull out the plug from the power socket;  
close the water tap;  
if necessary, wait until the water has cooled  
down;  
open the pump door;  
place a bowl on the floor and place the end  
of the emergency emptying hose into the  
bowl. Remove its cap. The water should  
drain by gravity into the bowl. When the bowl  
is full, put the cap back on the hose. Empty  
the bowl. Repeat the procedure until water  
stops flowing out;  
clean the pump if necessary as previously  
described;  
replace the emergency emptying hose in its  
seat after having plugged it;  
screw the pump cover again and close the  
door.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
20  
What to do if...  
IMPORTANT!  
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily  
without calling out an engineer. Before contacting your local Service Centre, please carry out the  
checks listed below.  
During machine operation it is possible that the red pilot light of the button 6 flashes, the buzzer  
sounds and one of the following alarm codes appears on the display to indicate that the machine  
is not working.  
E10: problem with the water supply  
E2 0: problem with water draining  
E40: door open.  
Once the problem has been eliminated, press the button 6 to restart the programme. If after all  
checks, the problem persists, contact your local Service Centre.  
Malfunction  
Possible Cause / Solution  
The door has not been closed. E40  
• Close the door firmly.  
The plug is not properly inserted in the power socket.  
• Insert the plug into the power socket.  
There is no power at the socket.  
• Please check your domestic electrical installation.  
The main fuse or the fuse in the plug has blown.  
• Replace the fuse.  
The washing machine does not start:  
The selector dial is not correctly positioned and the  
button 6 has not been pressed.  
• Please turn the selector dial and press the button  
6 again.  
The delay start has been selected.  
• If the laundry are to be washed immediately, cancel  
the delay start.  
The Child Safety Lock function has been activated.  
• Deactivate this function.  
The water tap is closed. E10  
• Open the water tap.  
The inlet hose is squashed or kinked. E10  
• Check the inlet hose connection.  
The machine does not fill:  
The filter in the inlet hose is blocked. E10  
• Clean the water inlet hose filter.  
The door is not properly closed. E40  
• Close the door firmly.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
21  
Malfunction  
Possible Cause / Solution  
The end of the drain hose is too low.  
• Refer to relevant paragraph in «water drainage»  
section.  
The machine fills then empties  
immediately:  
The drain hose is squashed or kinked. E2 0)  
• Check the drain hose connection.  
The drain pump is clogged. E2 0  
• Clean the drain pump.  
The machine does not empty and/or  
does not spin:  
The option  
selected.  
or «Night Cycle» has been  
«Rinse hold»  
• Select the draining or spinning programmes.  
The laundry is not evenly distributed in the drum.  
• Redistribute the laundry.  
Too much detergent or unsuitable detergent (creates  
too much foam) has been used.  
• Reduce the detergent quantity or use another one.  
Check whether there are any leaks from one of the  
inlet hose fittings. It is not always easy to see this as  
the water runs down the hose; check to see if it is  
damp.  
There is water on the floor:  
• Check the water inlet hose connection.  
The inlet or drain hose is damaged.  
• Replace it with a new one.  
The cap on the emergency emptying hose has not  
been replaced after cleaning the pump.  
• Refit the cap on the emergency emptying hose and  
place the latter back in its seat.  
Too little detergent or unsuitable detergent has been  
used.  
• Increase the detergent quantity or use another one.  
Stubborn stains have not been treated prior to  
washing.  
• Use commercial products to treat the stubborn  
stains.  
Unsatisfactory washing results:  
The correct temperature was not selected.  
• Check if you have selected the correct  
temperature.  
Excessive laundry load.  
• Reduce the laundry load.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
22  
Malfunction  
Possible Cause / Solution  
The programme is still running.  
• Wait the end of washing cycle.  
The door lock has not been released.  
• Wait a few minutes until the «Door» light has gone  
off.  
The door will not open:  
There is water in the drum.  
• Select drain or spin programme to empty out the  
water.  
The transit bolts and packing have not been  
removed.  
• Check the correct installation of the appliance.  
The support feet have not been adjusted.  
• Check the correct levelling of the appliance.  
The laundry is not evenly distributed in the drum.  
• Redistribute the laundry.  
The machine vibrates or is noisy:  
Maybe there is very little laundry in the drum.  
• Load more laundry.  
The electronic unbalance detection device has cut in  
because the laundry is not evenly distributed in the  
drum. The laundry is redistributed by reverse rotation  
of the drum. This may happen several times before  
the unbalance disappears and normal spinning can  
resume. If, after 10 minutes, the laundry is still not  
evenly distributed in the drum, the machine will not  
spin. In this case, redistribute the load manually and  
select the spin programme.  
Spinning starts late or the machine  
does not spin:  
Redistribute the laundry.  
If the load is very small, add more items, redistribute  
the load manually and then select the spinning  
programme.  
The machine is fitted with a type of motor which  
makes a different noise compared with other  
traditional motors. This new motor ensures a softer  
start and more even distribution of the laundry in the  
drum when spinning, as well as increased stability of  
the machine.  
The machine makes an unusual noise  
No water is visible in the drum  
Machines based on modern technology operate very  
economically using very little water without affecting  
performance.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
23  
If you are unable to identify or solve the problem, contact our  
service centre.  
Before telephoning, make a note of the model, serial number  
and purchase date of your machine: the Service Centre will  
require this information.  
Mod. ... ... ...  
Prod. No. ... ... ...  
Ser. No. ... ... ...  
Technical data  
Dimensions  
Width  
60 cm  
Height  
85 cm  
63 cm  
Depth (including the porthole)  
Electrical connection Voltage -  
Overall power - Fuse  
Information on the electrical connection is given on the rating  
plate on the inner edge of the appliance door  
Water supply pressure  
Maximum Load  
Minimum  
Maximum  
0,05 MPa  
0,8 MPa  
Cotton  
Synthetics  
Delicates  
Woollens and handwash  
70 kg  
3.5 kg  
3.5 kg  
2.0 kg  
Spin Speed  
Maximum  
0
1400 rpm  
Download from Www.Somanuals.com. All Manuals Search And Download.  
24  
Consumption values  
Programme  
duration  
(in hours and  
minutes)  
Programme  
Energy  
consumption  
(in kWh)  
Water  
consumption  
(in litres)  
Cottons 95°C  
2.2  
1.19  
1.4  
65  
52  
62  
57  
Cottons 60° Eco(*)  
Cottons 60°C - 40°C  
Cottons 40° Eco  
1.2  
Delicates 40°C - 30°C  
Wool 40°C  
0.55  
0.35  
0.25  
58  
52  
52  
Handwash 30°C - Cold  
Information  
The consumption data shown on this chart is to  
be considered purely indicative, as it may vary  
depending on the quantity and type of laundry,  
on the inlet water temperature and on the  
ambient temperature. It refers to the highest  
temperature for each wash programme.  
(*) The “Cottons 60° Eco” is the reference  
programme with a load of 7 kg for the data  
entered in the energy label, in compliance  
with EEC 92/75 standards.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
25  
Installation instruction  
Unpacking  
All transit bolts and packing must be removed  
before using the appliance.  
5. Remove the bracket D, refit the six smaller  
bolts C and slide out the relevant plastic  
spacer E.  
You are advised to keep all transit devices so  
that they can be refitted if the machine ever  
has to be transported again.  
6. Remove the polystyrene block fitted on the  
door seal.  
7. Fill the smaller upper hole and the two large  
ones with the corresponding plastic plug  
caps supplied in the bag containing the  
instruction booklet.  
1. After removing all the packaging, carefully  
lay machine on it’s back to remove the  
polystyrene base from the bottom.  
2. Remove the power supply cable, the inlet  
and the draining hoses from the hose  
holders on the rear of the appliance.  
Positioning  
Install the machine on a flat hard floor. Make  
sure that air circulation around the machine is  
not impeded by carpets, rugs etc. Check that  
the machine does not touch the wall or other  
kitchen units.  
A
C
Water inlet  
B
The inlet hose is already screwed on the back  
of the appliance.  
B
C
1. Set the hose correctly by loosening the ring  
nut. After positioning the inlet hose, be sure  
to tighten the ring nut again to prevent  
leaks.  
3. With a suitable spanner unscrew and  
remove the central rear bolt A.  
4. Unscrew and remove the two large rear  
bolts B and the six smaller bolts C.  
Do not place the inlet hose downwards. Angle  
the hose to the left or right depending on the  
position of your water tap (see picture).  
E
C
D
C
HEC0006  
Download from Www.Somanuals.com. All Manuals Search And Download.  
26  
2. This appliance must be connected to a  
cold water supply. Connect the hose to a  
tap with a 3/4” thread. The inlet hose must  
not be lengthened. If it is too short and you  
do not wish to move the tap, you will have  
to purchase a new, longer hose specially  
designed for this type of use..  
Special  
Off  
Cottons  
S
p
o
r
t
4
0
°
95°  
3h  
6h  
9h  
S
p
o
r
t
S
h
o
e
s
4
0
°
60° Eco  
60°  
1000  
900  
Silk  
M
i
n
i
3
0
'
4
0
°
E
c
o
700  
Prewash  
Intensive  
Wash  
Door  
End  
Cold  
Hand  
40°  
Synthetics  
50°  
Super  
Quick  
Wash  
30°  
ool  
1
0
0
0
6
k
g
Options  
E
x
t
r
a
R
i
n
s
e
Start/Pause  
Spin  
W
40°  
aIron 40°  
Spin  
Drain  
40°  
R
i
n
s
e
3
0
°
ZWF10070W  
Delicates  
38 mm (1.5”)  
standpipe  
diameter  
NOTE  
Firstly form a hook in the end of the drain  
hose using the «U» piece supplied. Place the  
drain hose into your standpipe, which should  
have an internal diameter of approximately  
38mm thus ensuring there is an air break  
between the drain hose and standpipe.  
When discharging into a standpipe ensure that  
the top of the standpipe is no more than 90  
cm (35.4'') and no less than 60 cm (23.6'')  
above floor level.  
Installation should  
comply with local  
water authority and  
building regulations’  
requirements.  
The appliance must be connected to a cold  
water supply.  
A minimum water pressure of 0.05 MPa (0.5  
bar) is required for safe operation of the  
appliance.  
Special  
Spor  
t
40°  
Off  
95°  
Cottons  
3h  
6h  
9h  
Spor  
t
S
h
o
e
s
4
0
°
60° Eco  
60°  
1000  
900  
Silk  
Mini 30'  
Cold  
4
0
°
E
c
o
700  
Prewash  
Intensive  
Wash  
Door  
End  
40°  
Synthetics  
50°  
Hand  
Super  
Quick  
W
ash  
1
0
0
0
6
k
g
30°  
ool  
Spin  
Options  
E
x
t
r
a
R
i
n
s
e
Start/Pause  
W
40°  
ay Ion 40°  
Spin  
Drain  
40°  
Rinse 30° Delicates  
ZWF10070W  
If you cannot make the cold water connection  
direct from the rising mains, you may be able  
to operate the appliance from your cold water  
storage system.  
There should be a minimum vertical distance of  
5.02m (16.5 ft) between the appliance’s inlet  
and the bottom of the water storage tank.  
The drain hose may be extended to a  
maximum of 4 metres. An additional drain  
hose and joining piece is available from your  
local Service Force Centre. The joining piece  
must have an internal diameter of 18mm.  
Water drainage  
This appliance is designed to be permanently  
plumbed into your home's drainage system  
using one of the following methods.  
If your drain hose  
looks like this (see  
below) you do not  
require the «U»  
piece. Just push the  
hose firmly into the  
standpipe.  
1. Into a drainage standpipe.  
U” piece  
supplied  
2. Onto a sink outlet spigot.  
If the outlet spigot has not been used before,  
remove any blanking plug that may be in  
place.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
27  
Special conditions  
If the floor is carpeted or covered with crumbly  
or soft material, insert a rigid support base  
under the feet to prevent noise, vibration or  
displacement. The base should protrude a few  
centimetres beyond the edges of the machine.  
Loop  
WARNING!  
Push the drain hose onto the spigot and secure  
with a clip, ensure a loop is formed in the drain  
hose (see diagram) to prevent waste from the  
sink entering the washing machine.  
The machine should NOT be placed on deep  
pile carpeting.  
NOTE  
Please ensure that when the appliance is  
installed it is easily accessible for the engineer  
in the event of a breakdown.  
Important!  
Before connecting the machine to new  
pipework or to pipework that has not been  
used for some time, run off a reasonable  
amount of water to flush out any debris that  
may have collected in the pipes.  
In the interest of the environment  
Washing machines should be connected to the  
FOUL drainage system, the water will then be  
taken to a sewage works for treatment before  
being discharged safely into a river. It is  
essential that these appliances are not  
connected to the surface water drainage  
system as this water is discharged directly into  
a river or stream and may cause pollution.  
If you require any further advice please contact  
your local water authority.  
Levelling  
Level the washing machine by raising or  
lowering the feet. The feet may be tight to  
adjust as they incorporate a self locking nut,  
but the machine MUST be level and stable.  
If necessary, check the  
setting with a spirit  
level.  
SHOWER  
Any necessary adjustment can be made with a  
spanner. Accurate levelling prevents vibration,  
noise and displacement of the machine during  
operation.  
SINK TOILET  
BATH  
BIDET  
WASHING  
MACHINE  
DISHWASHER  
Never place cardboard, wood or similar  
materials under the machine to compensate for  
any unevenness in the floor.  
RAINWATER  
'RUN-OFF'  
FOUL DRAIN  
Some vibration is inevitable, especially if  
mounted on a wooden floor.  
Sprung wooden floors are particularly  
susceptible to vibration. For advice, consult a  
builder. If possible, always place the machine  
on a solid floor.  
SURFACE WATER  
FOUL SEWERS  
DRAINS & SEWERS  
SEWAGE  
TREATMENT  
WORKS  
UNTREATED  
DISCHARGE  
TREATED  
DISCHARGE  
RIVER  
RIVER  
Download from Www.Somanuals.com. All Manuals Search And Download.  
28  
Electrical connection  
The wire coloured blue must be connected to  
the terminal marked «N» or coloured black.  
Any electrical work required to install this  
appliance should be carried out by a qualified  
electrician or competent person.  
The wire coloured brown must be connected to  
the terminal marked «L» or coloured red.  
Upon completion there must be no cut, or stray  
strands of wire present and the cord clamp  
must be secure over the outer sheath.  
WARNING!  
This appliance must be earthed.  
The manufacturer declines any liability  
should this safety measure not be  
observed.  
Before switching on, make sure the electricity  
supply voltage is the same as that indicated  
on the appliance’s rating plate.  
WARNING!  
A cut off plug inserted into a 13 amp socket  
is a serious safety (shock) hazard.  
Ensure that the cut off plug is disposed of  
safely. Should the appliance power supply  
cable need to be replaced, this must be  
carried out by our Service Force Centre.  
IMPORTANT!  
Information on the electrical connection is  
given on the rating plate on the inner edge  
of the appliance door.  
The power supply cable must be easily  
accessible after installing the appliance.  
Permanent connection  
The appliance is supplied with a 13amp plug  
fitted. In the event of having to change the  
fuse in the plug supplied, a 13amp ASTA  
approved (BS1363/A) fuse must be used.  
In the case of permanent connection it is  
necessary that you install a double pole switch  
between the appliance and the electricity  
supply (mains), with a minimum gap of 3mm  
between the switch contacts and of a type  
suitable for the required load in compliance  
with the current electrical regulations.  
The switch must not break the yellow and  
green earth cable at any point.  
Should the plug need to be replaced for any  
reason, proceed as described below.  
The wires in the mains lead are coloured in  
accordance with the following code:  
Green and Yellow ..............................- Earth  
Blue ....................................................- Neutral  
Brown..................................................- Live  
GREEN &YELLOW  
E
The wire coloured  
green and yellow must  
be connected to the  
L
N
terminal marked with  
BROWN  
the letter «E» or by the  
BLUE  
earth symbol  
or  
CORD CLAMP  
coloured green and yellow.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
29  
Environmental concerns  
Packaging materials  
Ecological hints  
The materials marked with the symbol  
recyclable.  
>PE<=polyethylene  
>PS<=polystyrene  
>PP<=polypropylene  
This means that they can be recycled by  
disposing of them properly in appropriate  
collection containers.  
are  
To save water, energy and to help protect the  
environment, we recommend that you follow  
these tips:  
Normally soiled laundry may be washed  
without prewashing in order to save  
detergent, water and time (the environment  
is protected too!).  
The machine works more economically if it is  
fully loaded.  
Old machine  
Use authorised disposal sites for your old  
appliance. Help to keep your country tidy!  
With adequate pre-treatment, stains and  
limited soiling can be removed; the laundry  
can then be washed at a lower temperature.  
Measure out detergent according to the  
water hardness, the degree of soiling and  
the quantity of laundry being washed.  
The symbol  
on the product or on its  
packaging indicates that this product may not  
be treated as household waste. Instead it  
should be taken to the appropriate collection  
point for the recycling of electrical and  
electronic equipment. By ensuring this product  
is disposed of correctly, you will help prevent  
potential negative consequences for the  
environment and human health, which could  
otherwise be caused by inappropriate waste  
handling of this product. For more detailed  
information about recycling of this product,  
please contact your local council, your  
household waste disposal service or the shop  
where you purchased the product.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
132 962 510 - 01 - 28 2008 Subject to change without notice  

Westinghouse Landscape Lighting 36308 User Manual
Whirlpool Ventilation Hood RH8930XLS User Manual
Whirlpool Washer Dryer 3SLSR6233MQ0 User Manual
White Outdoor Lawn Mower Z 180, Z 180L, Z 200 User Manual
White Rodgers Thermostat 24A07A 1 User Manual
Windmere Blender BD140 User Manual
Yamaha Automobile Parts F200 User Manual
Yamaha Network Card DSP1D User Manual
Zanussi Oven ZUG 78 User Manual
Zenoah Chainsaw G3300 User Manual