ZANUSSI
WASHING MACHINE
TE 825 V
Instructions manual
146 4583 00 - 02/03
Download from Www.Somanuals.com. All Manuals Search And Download.
A. FOR THE USER
1. WARNINGS
Keep this user’s manual with your washing machine. If you sell your washing machine or give it away, make sure that
it is accompanied by its user’s manual. The new user can then be informed of how the washing machine operates
and read relevant warnings.
These warnings have been written for your safety and for the safety of others. Please read these comments
carefully before installing and using your washing machine. Thank you for your attention.
1.1. Usage
•
•
Select the «Drain» programme and make sure it
works until it is complete.
Switch the washing machine off by putting the pro-
gram selector to the «Off»* position or pressing on
•
When you receive your washing machine, unpack it
or have it unpacked immediately. Check its general
appearance. Make any reserves in writing on the
delivery form and keep a copy.
•
•
•
Your washing machine was designed for use by
adults. Make sure that children do not touch it or
use it as a toy.
Do not modify or attempt to modify the characteris-
tics of this washing machine. This could be dange-
rous for you.
Your washing machine is intended for normal
domestic use. Do not use it for commercial or
industrial purposes of for any purpose other than
that for which it was designed : to wash, to rince
and to spin.
the «On/Off»* key.
•
•
Unplug the washing machine.
Screw in the water inlet pipe and install the drain
pipe.
Water that remained in the pipes will then be evacua-
ted, thus preventing the formation of frost or ice that can
damage your washing machine.
The next time you want to use your washing machine,
make sure that it is installed in a room in which the tem-
perature is above 0°C.
•
•
•
•
Unplug the power suplly plug and close the water
supply tap every time after using your washing
machine.
Only wash articles that can resist machine
washing. Refer to the instructions on the label for
each article.
Do not wash underwear with bones, or any material
without hems, or torn materials in your washing
machine.
Remember to remove all coins, safety pins, bora-
ches, screws, etc., before each wash. They can
cause serious damage if they are left in your
washing.
Do not put articles in your washing machine if you
have used a solvent, alcohol, trichloroethylene, etc.,
to remove stains from them. If you must use these
stain removers, wait until the product has evapora-
ted before putting the articles in the drum.
Collect all small articles such as socks, belts, etc.,
in a small cloth bag or pillow case.
Use the quantity of detergent indicated in the «pro-
portioning of detergents» section.
Always unplug the washing machine before clea-
ning it and doing any maintenance.
1.3. Scrapping
All materials marked with the
symbol can be recy-
cled. Put them in a waste tip (ask for information from
your municipal offices) so that they can be recovered
and recycled.
When you take your washing machine to the tip, make
sure that everything that could be dangerous is out of
service ; cut the power supply cable flush with the sur-
face of your washing machine.
1.4. Protection of the environment
•
We recommend that the following instructions should
be followed to achieve savings in water and energy and
therefore to contribute to protection of the environment:
•
•
•
•
If possible, use the washing machine at full capacity
rather than with partial loads (however, do not over-
load the drum).
•
•
Only use the Prewash or Soak function for very
dirty washing.
Use a detergent dose adapted to the water hard-
ness (see «proportioning of detergents» section)
and to the amount of washing and how dirty it is.
1.2. Precautions against frost
If your washing machine is exposed to temperatures
below 0°C, take the following precautions :
•
•
Close the tap and disconnect the water supply pipe.
Put the end of this pipe and the drain pipe into a
bowl on the floor.
*depending on model
3
Download from Www.Somanuals.com. All Manuals Search And Download.
2. WASHING MACHINE DESCRIPTION
1
2
1 - Control panel
2 - Lid opening handle
3 - Leveling screws
4 - Filter door
5 - Lever for moving the washing machine
5
4
3
2.1. The detergents dispenser
Symbols
1 - prewash
3 - softener
(do not exceed the MAX mark)
2
1
3
2 - wash
4 - softener overflow (if overfilled)
4
2.2. The control panel
1 - «Delayed start» pushbutton
2 - «Rinse plus» pushbutton
3 - «Quick wash» pushbutton
4 - «Rinse Hold» pushbutton
5 - «Start/Pause» pushbutton
6 - Program and information display lights
7 - Spinning speed variator
8 - Program selector
2
4
1
5
3
8
7
6
146 4583 00
4
Download from Www.Somanuals.com. All Manuals Search And Download.
3.4. Choice of the spinning speed
3. HOW TO DO A WASH ?
Before the first wash in your washing machine, we re-
commend that you should do a preliminary wash at
90°C with detergent but without any washing to clean
the tub.
The maximum spin speed is de-
fined as a function of the type of
washing and depending on the
selected program.
However, you can reduce the
speed or choose the rinse hold*,
drain*, or spinning suppression*
positions.
3.1. Loading the washing
•
•
Lift the machine cover.
Open the drum by pressing on the locking button A;
the two flaps automatically separate.
Insert the washing, close the drum and the cover of
your washing machine.
•
3.5. Choice of the required option
The
various
options
Warning : before you close
the cover of your washing
machine, make sure that the
drum door is properly closed:
•the two flaps latched
together,
should be chosen after
the program has been
displayed and before
pressing the Start/Pause
pushbutton.
A
•the locking button A exten-
ded.
Press the required pushbutton(s) ; the corresponding
lights come on. When you press again, the lights go off.
When one of these options is not compatible with the
chosen program, the corresponding light will flash for a
few seconds (see program table).
3.2. Proportioning of detergents
Your washing machine was designed to reduce water
and detergent consumption, therefore reduce the do-
ses recommended by detergent manufacturers.
3.5.1. «Delayed start» pushbutton
This option delays start of the program. Select the num-
ber of hours after which you want the program to begin
by pressing on the pushbutton one or several times.
Pour the powder detergent dose into the wash com-
partment
you chose the «prewash» option. Pour in the softener
into the compartment if you wish.
and into the prewash compartment
if
3.5.2. «Rinse plus» pushbutton
This option adds two rinses on Cotton, Synthetics and
Delicates programs. It is advised for allergic people to
detergent products and in areas with fresh water.
If you are using a different type of detergent, refer to the
«detergents and additives» section in the washing gui-
de.
3.5.3. «Quick wash» pushbutton
If you select this function, the wash time is reduced
depending on which program you chose.
3.3. Choice of the required program
The programs table will tell you which is the appropriate
program for your washing type (see § 4).
3.5.4. «Rinse hold» pushbutton
If you use this pushbutton, the tub remains full of water
at the end of the last rinse to prevent the washing from
becoming creased if it is not taken out of the drum as
soon as the washing machine is stopped.
Put the program selector
onto the required program.
3.6. Starting the program
After you chose the washing program, press
the Start/Pause pushbutton to start the cy-
cle. The corresponding light stays on.
It is normal that the program selector does
not turn during the cycle.
* depending on model
5
Download from Www.Somanuals.com. All Manuals Search And Download.
When the washing cycle begins, the
«washing» light is on.
3.7. Action during a program
3.7.1. Adding of laundry
Press the Start/Pause pushbutton : the corresponding
light flashes as long as the program is paused. The
opening of the lid is possible only 2 minutes after the
washing machine stops. Press the same pushbutton
again to resume the program.
For reasons of safety, you cannot open the cover if the
temperature of the washing water is too high.
3.7.2. Modifying the current program
Before modifying the current program, you must put the
washing machine to pause by pressing on the «Start/
Pause» pushbutton. If it is impossible to make the
modification, the corresponding light flashes for few
seconds. If you decide to change the program in any
case, you will need to cancel the current program (see
below).
3.7.3. Cancelling the program
If you want to cancel a program, turn the program
selector knob to the «off» position of the program
selector.
You can then select a new program after cancelling the
previous one.
3.8. End of program
The washing machine stops automatically. The «cycle
end» light goes on. The opening of the lid is only
possible 2 minutes after the washing machine stops.
If you choose the rinse hold pushbutton, the rinse hold
light illuminates to inform you that water has to be
drained before you can open the cover. To terminate
the cycle, you can then spin the washing by choosing
the spinning program or drain it by choosing the drain
program.
Turn the program selector knob to the «Off» position.
Take out the washing.
Pull out the power supply plug and close the water sup-
ply tap.
Note: we recommend that you should leave the cover
and the drum open after use to air the washing drum.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
4. PROGRAMS TABLE
The following does not show all possibilities, but simply the most frequent settings.
Program
Washing type
Load
Possible
options
Tempe-
ra-tures
Approximate
consumptions
liters
58
°C
60
kWh
min
Cotton
B
4,5 kg
1,30 120-130
White or color, for exam-
ple normally dirty work
clothes, bed linen, table
linen, underwear, towels.
Delayed Start
Rinse Plus
Cotton
A
4,5 kg
95
74
2,30 165-175
with prewash
Quich Wash
(excepted on E60°)
Rinse Hold
Cotton
Cotton
Cotton
Coloured
Delicates
C
Q
R
4,5 kg
4,5 kg
4,5 kg
40
30
58
58
48
0,65 115-125
0,35 110-120
0,85 135-145
E 60 (*)
Saving energy E
Synthetics
D
2,0 kg
Delayed Start
Rinse Plus
Quich Wash
Rinse Hold
50
40
57
0,90
85 - 95
Synthetic fabrics, under-
wear, color fabrics, non-
iron shirts, blouses.
Delicates
F
2,0 kg
Delayed Start
Rinse Plus
Quich Wash
Rinse Hold
52
0,60
65 - 75
For all delicate mate-
rials, for example cur-
tains.
Hand wash
Very delicate washing
marked «wash by hand».
L
1,0 kg
1,0 kg
Delayed Start
Rinse Hold
30
40
53
53
0,30
0,35
45 - 55
50 - 60
Wool
M
Delayed Start
Rinse Hold
Machine washable wool
marked «pure wool,
washable in machine,
non shrinking».
Flash
N
2,0 kg
1,0 kg
Delayed Start
Rinse Hold
30
40
43
0,30
30 - 40
For only slightly dirty ma-
terials, except for wool.
Easy ironing
P
Delayed Start
Rinse Hold
65
42
0,40
0,05
85 - 95
30 - 40
Rinse
G
3 rinsings with liquid additive.
Spin drying.
Hand washed washing
may be rinsed with this
program.
(*) Reference program for tests according to standard IEC 456 (60° Cotton program).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
5.3. Detergents and additives
5. WASHING GUIDE
Only use detergents and additives suitable for use in a
washing machine. Read the manufacturer's instruc-
tions and respect sections 2.1 and 3.2.
5.1. Sorting and preparing your
washing
Powder detergents can be used without restriction; li-
quid detergents should be poured either in the propor-
tioning bowl directly in the drum, or in the wash
compartment provided that the washing machine is
started immediately; detergents in tablets or doses
must be put into the wash compartment of the deter-
gents dispenser in your washing machine.
The quantity of detergent to be used depends on the
amount of washing to be washed, the hardness of the
water and how dirty the washing is.
If the water is soft, you can reduce the doses slightly.
Increase the doses slightly if the water is hard (it is re-
commended to use a water softener) or if the washing
is very dirty or stained.
You can ask the water distribution company in your re-
gion or any other competent authority to find out the de-
gree of hardness of your water.
•
Sort the washing by type and care symbol (see
chapter 5.4: International symbols for care of texti-
les): normal wash for strong washing that can
resist energetic wash and spin; delicate wash for
delicate washing that should be treated more care-
fully. For mixed loads composed of articles of diffe-
rent types of fibers, choose a program and
temperature suitable for the most fragile fiber.
Wash white washing and color washing separa-
tely. Otherwise, the white washing may be colored
or look gray.
New clothes very often have too much color. Prefe-
rably wash new clothes separately for the first time.
Respect "wash separately" and "wash several
times separately" care instructions.
Empty pockets and spread out the washing.
Take off all loose buttons, pins and hooks and eyes.
Close zip fasteners, tie knots in laces and straps.
Turn clothes made of several layers of textiles (slee-
ping bags, anoraks, etc.), colored hosiery and wool
and textiles with add-on decorations, inside out.
Wash small delicate items (socks, tights, bras, etc)
in a washing net.
•
•
•
•
•
•
•
Treat curtains with special care. Remove curtain
hooks and put net curtains in a net bag or a sachet.
5.2. Washing load depending on the
nature of the material
The quantity of washing that you put in your drum must
not exceed the maximum capacity of your washing ma-
chine. This capacity may vary depending on the nature
of your textiles. Reduce the quantity of washing if it is
very dirty or if you have terry cloth type materials.
Not all textiles have the same volume and the same wa-
ter retention capacity. This is why in general the drum
should be filled:
•
completely, but without excessive pressure for cot-
ton and linen, and for mixed washe,
•
•
half full for treated cottons and synthetic fibers,
about one third full for very delicate articles such as
net curtains and wool.
For a mixed wash, fill the drum as required for the most
delicate material.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
5.4. International symbols for care of textiles
NORMAL
WASH
Wash at
95°C
Wash at
60°C
Wash at
40°C
Wash at
30°C
Delicate
wash by
hand
Do not wash
DELICATE
WASH
JAVEL WATER
Bleaching with chlorine (Javel water) allowed
(only cold and with a dilute solution)
Do not bleach with chlorine (Javel water)
IRONING
High temperature
(max 200°C)
Average temperature
(max 150°C)
Low temperature
(max 100°C)
Do not iron
DRY
CLEANING
Dry cleaning
(all usual solvents)
Dry cleaning
(all solvents except
trichloroethylene)
Dry cleaning
(only oil solvents
and R113)
Do not dry clean
High
temperature
Moderate
Temperature
DRYING
Dry washing
spread out
Dry washing
hung up
Dry washing
on hanger
Drying in drum
allowed
Do not dry
in drum
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6.4. The drain filter
6. CARE AND CLEANING
Clean the filter at the bottom of the washing machine
regularly. The "filter"* light comes on if the filter is bloc-
ked. In this case clean it immediately. If you wash
washing that is very fluffy, clean it after each wash.
Do not do any cleaning operation until you have
unplugged the washing machine.
6.1. Descaling the washing machine
•
•
•
Open the door:
Normally there is no need to descale the washing ma-
chine if the detergent was correctly proportioned.
If descaling is necessary, use a special non-corrosive
product specially designed for washing machines that
you can find in the shops. Respect the proportion and
frequency of descaling shown on your packaging.
6.2. The surface
Clean the surface of your washing machine using lu-
kewarm water and a mild detergent. Never use alcohol,
solvents or similar products.
Drain residual water:
Put a receptacle under the
drain. Turn the cap in the anti-
clockwise direction until it is
vertical to release residual wa-
ter.
6.3. The detergents dispenser
Disassembly:
Press the clips on each side of
the detergents dispenser and
pull it upwards.
Remove the filter:
Unscrew the cap all the way
and take it off. Clean it thorou-
ghly with running water. Put
the assembly back and screw
it in the clockwise direction.
You can thus clean it using run-
ning water and a brush or a
twisted cloth. Check that the
siphons at the back of the de-
tergents dispenser are not
blocked.
Reassembly :
Put the detergents dispenser in
the notches until they lock.
*depending on model
10
Download from Www.Somanuals.com. All Manuals Search And Download.
7. OPERATING PROBLEMS
Many checks have been carried out during the manufacture of your washing machine. However, if you face a problem
with its operation, please read the following sections before calling the After Sales service.
Symptom
Cause
The washing machine will not start or will not fill:
•
•
the washing machine is not correctly connected, the elec-
trical installation is not working,
the cover of your washing machine and the drum flaps are
not correctly closed,
•
•
•
•
•
you did not control the program start correctly,
there is a power failure,
the water supply is closed off,
the water tap is closed,
the water inlet is blocked.
The washing machine fills up but empties again
immediately:
•
the drain siphon is attached too low (see installation sec-
tion).
The washing machine will not spin or will not
empty:
•
•
•
the drain pipe is blocked or kinked,
the drain filter is blocked,
the anti-unbalance mass safety device has tripped; bad
distribution of washing in the drum,
•
•
the «Drain» program or the «Rinse hold» option is selected,
the height of the drain siphon is wrong.
There is water on the floor around the washing
machine:
•
excess detergent has made too much foam that over-
flowed,
•
•
•
•
the detergent is not suitable for washing machine,
the drain siphon is not hooked on properly,
the drain filter was not put back into place,
the water inlet pipe is leaking.
Washing results are not satisfactory:
The machine is vibrating or noisy:
•
•
•
•
the detergent is not suitable for machine washing,
there is too much washing in the drum,
the washing program is not appropriate,
there is not enough detergent.
•
not all the packing was removed from the machine (see
unpacking section),
•
•
•
•
the washing machine is not leveled and properly packed,
the washing machine is too close to the wall or furniture,
the washing is not well distributed in the drum,
the load is not sufficient.
The washing cycle is much too long :
•
•
•
•
•
the water inlet is blocked,
there was a power supply failure or the water was cut off,
the motor temperature safety device tripped,
the water inlet temperature is lower than normal,
the foam detection safety system tripped (too much deter-
gent) and the washing machine evacuated the foam,
the anti-unbalance mass safety device tripped, an additio-
nal phase was added to distribute the washing in the drum
better.
•
The washing machine stops during a washing cy-
cle :
•
•
the water or electricity supply is defective,
a rinse hold was programmed.
The cover does not open during the cycle :
•
•
•
the «IMMEDIATE OPENING»* light is off,
the temperature of the washing water is too high.
the cover cannot open until 1 to 2 minutes after the
washing machine has stopped*.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Cause
The «DRUM POSITIONNING»* light** is not on at the
end of the cycle:
•
the drum could not reach the right position due to a persis-
tent unbalanced mass; turn the drum manually.
The «End»* light ** flashes 4 times***:
The «End»* light ** flashes 2 times***:
•
the cover is not correctly closed.
•
•
•
•
•
the drain filter is blocked,
the drain pipe is blocked or kinked,
the drain pipe is too high (see «installation»),
the drain pump is blocked,
the installation siphon is blocked.
The «End»* light ** flashes 1 time***:
•
•
the water tap is closed,
the water network has been cut off.
Softener of Javel water flows through the over-
flow orifice when filling* :
•
•
you did not put in the right amount,
the siphons at the back of the detergents dispenser are
blocked.
* Depending on the model.
** Eliminate the causes of the failure if you find them, and then press on the «Start/Pause» pusbutton to restart the
interrupted program.
*** Depending on the model, some acoustic signals may be activated.
8. GUARANTEE
Depending to the Sales Company.
9. AFTER SALES SERVICE
If you have an operating problem, refer to the " Operating problems " section. If any work is necessary after you have
made all your checks, your washing machine dealer is the first person authorized to take action. Otherwise, you can
always call Consumers Help that will inform you of the address of an After Sales Service.
When you call the After Sales Service, mention the model and product number of your washing machine, and its serial
number. This information is given on the inside of the filter door and on the name plate at the back of the washing
machine.
If any work is done on your washing machine, insist that your After Sales Service uses manufacturer certified spare
parts.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
B. FOR THE INSTALLER
1. WARNINGS
•
This washing machine is heavy. Take care when
moving it.
•
•
•
Please read the instructions in the "electrical con-
nections" chapter carefully before connecting your
washing machine.
After installing your washing machine, make sure
that it is not standing on its electrical power supply
cable.
When your machine is installed on a carpeted floor,
make sure that the carpet does not close off the
ventilation openings near the bottom of the
machine.
The power supply cable may be only replaced by
the After Sales Service.
•
You must remove the packing on the washing
machine before use. Failure to remove all transport
protection devices can cause damage to the
washing machine or nearby furniture. The washing
machine must be unplugged while packing is being
removed.
Do not allow any one other than a qualified plumber
to make the hydraulic connections necessary to
install your washing machine.
The washing machine must be plugged in to a
power outlet with a conform earth.
Call a qualified electrician if the electrical installa-
tion in your residence is such that you have to
modify it before you can connect your washing
machine.
•
•
•
•
•
Your manufacturer cannot be held responsible for
any damage resulting from a nonconform installa-
tion.
2. TECHNICAL CHARACTERISTICS
DIMENSIONS
Height
Width
Depth
850 mm
397 mm
600 mm
VOLTAGE / FREQUENCY
TOTAL POWER
230 V / 50 Hz
2300 W
WATER PRESSURE
Minimum
Maximum
0,05 MPa (0,5 bar)
0,8 MPa (8 bars)
Type 20x27
Connection to the water network
This washing machine complies with CEE directive 89-336 about the limitation of radioelectric disturbances
and directive CEE 73-23 for electrical safety.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
If you want to keep your
washing machine aligned with
the adjacent furniture, you can
cut the pipe support strip at the
back of your washing machine.
Leave the two side closers in
place.
3. INSTALLATION
3.1. Unpacking
Packing used to protect internal parts of
the washing machine during transport
must be removed before the washing
machine is put into service for the first ti-
me.
3.2. Position
Remove all packing from the
washing machine. Tilt the
washing machine sideways and
then remove the packing under
the motor, and straighten the
washing machine.
Put the washing machine on a flat hard floor in a well
ventilated room.
Make sure that your washing machine does not touch
the wall or any other furniture in the room.
3.3. Moving your washing machine
If you want to move your
washing machine, lift it onto its
rollers by pulling the lever at the
bottom of the washing machine
all the way to the left. When you
have put your washing machine
into the required location, put
the lever back into its initial
position.
Tilt the washing machine back-
wards, rotate it by a quarter of a
turn on one of its corner to re-
move the transport base.
Open the washing machine lid
and remove the immobilization
packing and plastic films.
Close the lid.
3.4. Leveling
Precise leveling will prevent vibrations, noise and mo-
vements of the washing machine during operation.
Make the washing machine le-
vel by adjusting the leveling
screw that is too short.
Unscrew the stand and locking
collar assembly (lift the
washing machine if necessary).
Use a 10 mm spanner to remo-
ve the two screws and spacers
at the back.
When the washing machine is
stable, maintain the stand on
the ground and turn the locking
collar as far as posible.
You can now see the openings
that must be closed with the ca-
ches in the pack attached to the
washing machine; do not forget
to fold down the central capsule.
3.5. Water inlet
Screw the supply ppe con-
nector onto the water inlet tap
(20x27 mm), remembering to
use the washer provided with
the washing machine.
Make sure that you have remo-
ved all these parts from your
washing machine and keep
them so that you can use them
again if you need them for future
transport.
Open the water inlet tap.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
You cannot prolong the water inlet pipe. If it is too short,
buy a longer pipe provided for this purpose.
3.6. Drain
The drain siphon must be pla-
ced inside a drain pipe (or in a
washbasin) at a height of
between 70 and 100 cm. Make
sure that it cannot fall.
•
Important: the drain pipe must never be prolonged.
If it is too short, call a professional.
3.7. Electrical connection
You can only connect this washing machine to 230 V
single phase power supply.
Check rating of the fuse line: 10 A at 230V.
The washing machine must not be connected through
an extension cable or a power bar.
Check that the earthing connection is conform with the
regulations in force.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
From the Electrolux Group. The world’s No.1 Choice.
The Electrolux Group is the world largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group
products (such as refrigerators, cookers, washing machines, vaccum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD
14 billion in more than 150 countries around the world.
Download from Www.Somanuals.com. All Manuals Search And Download.
|