Zanussi Washer TE 1132 V User Manual

WASHING MACHINES  
TE 1362 V - TE 1132 V  
TE 962 V  
Instructions manual  
146 4864 01 - 09/03  
Download from Www.Somanuals.com. All Manuals Search And Download.  
A. FOR THE USER  
1. WARNINGS  
Keep this user’s manual with your washing machine. If you sell your washing machine or give it away, make sure that  
it is accompanied by its user’s manual. The new user can then be informed of how the washing machine operates  
and read relevant warnings.  
These warnings have been written for your safety and for the safety of others. Please read these comments  
carefully before installing and using your washing machine. Thank you for your attention.  
1.1. Usage  
Select the «Drain» programme and make sure it  
works until it is complete.  
Switch the washing machine off by putting the pro-  
gram selector to the «Off»* position or pressing on  
the «On/Off»* key.  
Unplug the washing machine.  
Screw in the water inlet pipe and install the drain  
pipe.  
When you receive your washing machine, unpack it  
or have it unpacked immediately. Check its general  
appearance. Make any reserves in writing on the  
delivery form and keep a copy.  
Your washing machine was designed for use by  
adults. Make sure that children do not touch it or  
use it as a toy.  
Do not modify or attempt to modify the characteris-  
tics of this washing machine. This could be dange-  
rous for you.  
Your washing machine is intended for normal  
domestic use. Do not use it for commercial or  
industrial purposes or for any purpose other than  
that for which it was designed : to wash, to rinse  
and to spin.  
Water that remained in the pipes will then be evacua-  
ted, thus preventing the formation of frost or ice that can  
damage your washing machine.  
The next time you want to use your washing machine,  
make sure that it is installed in a room in which the tem-  
perature is above 0°C.  
Unplug the power suplly plug and close the water  
supply tap every time after using your washing  
machine.  
Only wash articles that can resist machine  
washing. Refer to the instructions on the label for  
each article.  
Do not wash underwear with bones, or any material  
without hems, or torn materials in your washing  
machine.  
Remember to remove all coins, safety pins, bora-  
ches, screws, etc., before each wash. They can  
cause serious damage if they are left in your  
washing.  
Do not put articles in your washing machine if you  
have used a solvent, alcohol, trichloroethylene, etc.,  
to remove stains from them. If you must use these  
stain removers, wait until the product has evapora-  
ted before putting the articles in the drum.  
Collect all small articles such as socks, belts, etc.,  
in a small cloth bag or pillow case.  
Use the quantity of detergent indicated in the «pro-  
portioning of detergents» section.  
Always unplug the washing machine before clea-  
ning it and doing any maintenance.  
1.3. Scrapping  
All materials marked with the  
symbol can be recy-  
cled. Put them in a waste tip (ask for information from  
your municipal offices) so that they can be recovered  
and recycled.  
When you take your washing machine to the tip, make  
sure that everything that could be dangerous is out of  
service ; cut the power supply cable flush with the sur-  
face of your washing machine.  
1.4. Protection of the environment  
We recommend that the following instructions should  
be followed to achieve savings in water and energy and  
therefore to contribute to protection of the environment:  
If possible, use the washing machine at full capacity  
rather than with partial loads (however, do not over-  
load the drum).  
Only use the Prewash or Soak function for very  
dirty washing.  
Use a detergent dose adapted to the water hard-  
ness (see «proportioning of detergents» section)  
and to the amount of washing and how dirty it is.  
1.2. Precautions against frost  
If your washing machine is exposed to temperatures  
below 0°C, take the following precautions :  
Close the tap and disconnect the water supply pipe.  
Put the end of this pipe and the drain pipe into a  
bowl on the floor.  
*depending on model  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
2. WASHING MACHINE DESCRIPTION  
1
2
1 - Control panel  
2 - Lid opening handle  
3 - Leveling screws  
4 - Filter door  
5 - Lever for moving the washing machine  
5
4
3
2.1. The detergents dispenser  
Symbols  
1 - prewash  
3 - softener  
(do not exceed the MAX mark)  
2
1
3
2 - wash  
4 - softener overflow (if overfilled)  
4
2.2. The control panel  
1 - «Daily wash / quick wash» pushbutton  
2 - «Prewash» pushbutton  
3 - «Super rinse» pushbutton  
4 - «Start/Start» pushbutton  
5 - «Delay» pushbutton  
6 - Program and information display lights  
7 - Spinning speed selector  
6 - Program selector  
1
3
5
2
4
7
8
6
Represented model : TE 1362 V  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
3.4. Choice of the spinning speed  
3. HOW TO DO A WASH ?  
Before the first wash in your washing machine, we re-  
commend that you should do a preliminary wash at  
90°C with detergent but without any washing to clean  
the tub.  
The maximum spin speed is de-  
fined as a function of the type of  
washing and depending on the  
selected program.  
However, you can reduce the  
speed or choose the rinse hold*,  
drain*, or spinning suppression*  
positions.  
3.1. Loading the washing  
Lift the machine cover.  
Open the drum by pressing on the locking button A;  
the two flaps automatically separate.  
Insert the washing, close the drum and the cover of  
your washing machine.  
3.5. Choice of the required option  
Warning : before you close  
the cover of your washing  
machine, make sure that the  
drum door is properly closed:  
The  
various  
options  
should be chosen after  
the programme has been  
displayed and before  
pressing the Start/Pause  
pushbutton.  
the two flaps latched  
together,  
• the locking button A exten-  
ded.  
A
Press the required pushbutton(s) ; the corresponding  
lights come on. When you press again, the lights go off.  
When one of these options is not compatible with the  
chosen programme, the corresponding light will flash  
for a few seconds (see programme table).  
3.2. Proportioning of detergents  
Your washing machine was designed to reduce water  
and detergent consumption, therefore reduce the do-  
ses recommended by detergent manufacturers.  
3.5.1. «Daily wash / Quick wash» pushbut-  
ton  
Pour the powder detergent dose into the wash com-  
This pushbutton allows to choose between two func-  
tions :  
partment  
you chose the «prewash» option. Pour in the softener  
into the compartment if you wish.  
and into the prewash compartment  
if  
«Daily wash» function :  
This pushbutton allows to realize a washing cycle with  
not soiled laundry in a reduced time.  
If you are using a different type of detergent, refer to the  
«detergents and additives» section in the washing gui-  
de.  
«Quick wash» function :  
If you select this function, the wash time is reduced de-  
pending on which program you chose.  
3.3. Choice of the required program-  
me  
3.5.2. «Prewash» pushbutton  
The washing machine does a prewash at 30°C  
maximum. The prewash finishes with a brief spinning  
for cotton and synthetic programs, and by a draining for  
delicates programs.  
The programmes table will tell you which is the appro-  
priate programme for your washing type (see § 4).  
Put the programme selector  
onto the required program-  
me ; the lights correspon-  
ding to the phases making  
up the programme will light  
up.  
3.5.3. «Super rinse» pushbutton  
This option adds two rinses on Cotton, Synthetics and  
Delicates programs. It is advised for allergic people to  
detergent products and in areas with fresh water.  
3.5.4. «Delayed start» pushbutton  
This option delays start of the programme. Select the  
number of hours after which you want the programme  
to begin by pressing on the pushbutton one or several  
times.  
* depending on model  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
Pull out the power supply plug and close the water sup-  
ply tap.  
3.6. Starting the programme  
After you chose the washing programme,  
Note: we recommend that you should leave the cover  
and the drum open after use to air the washing drum.  
press the Start/Pause pushbutton to start  
the cycle. The corresponding light stays on.  
It is normal that the programme selector  
does not turn during the cycle.  
When the washing cycle begins, the  
«washing» light is on.  
3.7. Action during a programme  
3.7.1. Adding of laundry  
Press the Start/Pause pushbutton : the corresponding  
light flashes as long as the programme is paused. You  
will then hear a double "click" in the locking device  
when the cover opens. Press the same pushbutton  
again to resume the programme.  
For reasons of safety, you cannot open the cover if the  
temperature of the washing water is too high.  
3.7.2. Modifying the current programme  
Before modifying the current programme, you must put  
the washing machine to pause by pressing on the  
«Start/Pause» pushbutton. If it is impossible to make  
the modification, the corresponding light flashes for few  
seconds. If you decide to change the programme in any  
case, you will need to cancel the current programme  
(see below).  
3.7.3. Cancelling the programme  
If you want to cancel a programme, turn the programme  
selector knob to the «off» position of the programme  
selector.  
You can then select a new programme after cancelling  
the previous one.  
3.8. End of program  
The washing machine stops automatically. You will  
hear a double "click" in the locking device when the  
cover opens. The cycle end light goes on.  
If you choose the rinse hold position on the spin speed  
variator, the rinse hold light* illuminates to inform you  
that water has to be drained before you can open the  
cover. To terminate the cycle, you can then spin the  
washing by choosing the spin program or drain it by  
choosing the drain program.  
Turn the program selector knob to the "Off" position.  
Take out the laundry.  
*depending to the model  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
4. PROGRAMS TABLE  
The following does not show all possibilities, but simply the most frequent settings.  
Program  
Washing type  
Load  
Possible  
options  
Tempera-  
tures  
Approximate  
consumptions  
°C  
liters  
kWh  
min  
COTTONS  
5 kg  
Daily wash /  
Quick wash  
(NOT on E 60°)  
Prewash  
Super Rinse  
Delay  
90  
E 60 (*)  
40  
63  
45  
58  
2,10  
0,95  
0,65  
145  
145  
120  
White or color, for exam-  
ple normally dirty work  
clothes, bed linen, table  
linen, underwear, towels.  
SYNTHETICS  
2,5 kg  
Daily wash /  
Quick wash  
Prewash  
Super rinse  
Delay  
cold  
57  
0,15  
70  
Synthetic fabrics, under-  
wear, color fabrics, non-  
iron shirts, blouses.  
Easy ironing  
1,0 kg  
2,5 kg  
40  
40  
65  
52  
0,40  
0,60  
90  
70  
DELICATES  
Daily wash /  
Quick wash  
Prewash  
Super rinse  
Delay  
For all delicate mate-  
rials, for example cur-  
tains.  
WOOL  
1,0 kg  
Delay  
cold  
53  
0,06  
45  
Machine washable wool  
marked «pure wool,  
washable in machine,  
non shrinking».  
HAND WASH  
Very delicate washing  
marked «wash by hand».  
1,0 kg  
2,5 kg  
Delay  
Delay  
30  
30  
53  
43  
0,30  
0,30  
50  
35  
SHORT CYCLE  
For only slightly dirty ma-  
terials, except for wool.  
Rinses  
3 rinsings with liquid additive.  
Spin drying.  
42  
0,05  
35  
Hand washed washing  
may be rinsed with this  
program.  
(*) Reference program for tests according to standard IEC 456 (E60° Cotton program).  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.3. Detergents and additives  
5. WASHING GUIDE  
Only use detergents and additives suitable for use in a  
washing machine. Read the manufacturer's instruc-  
tions and respect sections 2.1 and 3.2.  
5.1. Sorting and preparing your  
washing  
Powder detergents can be used without restriction; li-  
quid detergents should be poured either in the propor-  
tioning bowl directly in the drum, or in the wash  
compartment provided that the washing machine is  
started immediately; detergents in tablets or doses  
must be put into the wash compartment of the deter-  
gents dispenser in your washing machine.  
The quantity of detergent to be used depends on the  
amount of washing to be washed, the hardness of the  
water and how dirty the washing is.  
If the water is soft, you can reduce the doses slightly.  
Increase the doses slightly if the water is hard (it is re-  
commended to use a water softener) or if the washing  
is very dirty or stained.  
You can ask the water distribution company in your re-  
gion or any other competent authority to find out the de-  
gree of hardness of your water.  
Sort the washing by type and care symbol (see  
chapter 5.4: International symbols for care of texti-  
les): normal wash for strong washing that can  
resist energetic wash and spin; delicate wash for  
delicate washing that should be treated more care-  
fully. For mixed loads composed of articles of diffe-  
rent types of fibers, choose a program and  
temperature suitable for the most fragile fiber.  
Wash white washing and color washing separa-  
tely. Otherwise, the white washing may be colored  
or look gray.  
New clothes very often have too much color. Prefe-  
rably wash new clothes separately for the first time.  
Respect "wash separately" and "wash several  
times separately" care instructions.  
Empty pockets and spread out the washing.  
Take off all loose buttons, pins and hooks and eyes.  
Close zip fasteners, tie knots in laces and straps.  
Turn clothes made of several layers of textiles (slee-  
ping bags, anoraks, etc.), colored hosiery and wool  
and textiles with add-on decorations, inside out.  
Wash small delicate items (socks, tights, bras, etc)  
in a washing net.  
Treat curtains with special care. Remove curtain  
hooks and put net curtains in a net bag or a sachet.  
5.2. Washing load depending on the  
nature of the material  
The quantity of washing that you put in your drum must  
not exceed the maximum capacity of your washing ma-  
chine. This capacity may vary depending on the nature  
of your textiles. Reduce the quantity of washing if it is  
very dirty or if you have terry cloth type materials.  
Not all textiles have the same volume and the same wa-  
ter retention capacity. This is why in general the drum  
should be filled:  
completely, but without excessive pressure for cot-  
ton and linen, and for mixed washe,  
half full for treated cottons and synthetic fibers,  
about one third full for very delicate articles such as  
net curtains and wool.  
For a mixed wash, fill the drum as required for the most  
delicate material.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
5.4. International symbols for care of textiles  
NORMAL  
WASH  
Wash at  
95°C  
Wash at  
60°C  
Wash at  
40°C  
Wash at  
30°C  
Delicate  
wash by  
hand  
Do not wash  
DELICATE  
WASH  
JAVEL WATER  
Bleaching with chlorine (Javel water) allowed  
(only cold and with a dilute solution)  
Do not bleach with chlorine (Javel water)  
IRONING  
High temperature  
(max 200°C)  
Average temperature  
(max 150°C)  
Low temperature  
(max 100°C)  
Do not iron  
DRY  
CLEANING  
Dry cleaning  
(all usual solvents)  
Dry cleaning  
(all solvents except  
trichloroethylene)  
Dry cleaning  
(only oil solvents  
and R113)  
Do not dry clean  
High  
temperature  
Moderate  
Temperature  
DRYING  
Dry washing  
spread out  
Dry washing  
hung up  
Dry washing  
on hanger  
Drying in drum  
allowed  
Do not dry  
in drum  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
6.4. The drain filter  
6. CARE AND CLEANING  
Clean the filter at the bottom of the washing machine  
regularly. The "filter"* light comes on if the filter is blo-  
cked. In this case clean it immediately. If you wash  
washing that is very fluffy, clean it after each wash.  
Do not do any cleaning operation until you have  
unplugged the washing machine.  
6.1. Descaling the washing machine  
Open the door, with a screwdriver for example:  
Normally there is no need to descale the washing ma-  
chine if the detergent was correctly proportioned.  
If descaling is necessary, use a special non-corrosive  
product specially designed for washing machines that  
you can find in the shops. Respect the proportion and  
frequency of descaling shown on your packaging.  
6.2. The surface  
Clean the surface of your washing machine using lu-  
kewarm water and a mild detergent. Never use alco-  
hol, solvents or similar products.  
Drain residual water:  
6.3. The detergents dispenser  
Put a receptacle under the  
drain. Turn the cap in the anti-  
clockwise direction until it is  
vertical to release residual wa-  
ter.  
From time to time, you must clean the detergents dis-  
penser in order to eliminate the possible wastes of the  
detergents and then to avoid an operating problem.  
The detergent dispenser is very easy to remove for a li-  
ght cleaning.  
Disassembly:  
Press the clips on each side of  
the detergents dispenser and  
pull it upwards.  
Remove the filter:  
Unscrew the cap all the way  
and take it off. Clean it tho-  
roughly with running water.  
Put the assembly back and  
screw it in the clockwise direc-  
tion.  
You can thus clean it using  
running water and a brush or a  
twisted cloth. Check that the  
siphons at the back of the de-  
tergents dispenser are not  
blocked.  
After cleaning the filter, you are required to closed the  
door. In fact, for reasons of safety, the door must be  
closed when the appliance is working.  
Reassembly :  
Put the detergents dispenser in  
the notches until they lock.  
*depending on model  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
7. OPERATING PROBLEMS  
Many checks have been carried out during the manufacture of your washing machine. However, if you face a problem  
with its operation, please read the following sections before calling the After Sales service.  
Symptom  
Cause  
The washing machine will not start or will not fill:  
the washing machine is not correctly connected, the elec-  
trical installation is not working,  
the cover of your washing machine and the drum flaps are  
not correctly closed,  
you did not control the program start correctly,  
there is a power failure,  
the water supply is closed off,  
the water tap is closed,  
the water inlet is blocked.  
The washing machine fills up but empties again  
immediately:  
the drain siphon is attached too low (see installation sec-  
tion).  
The washing machine will not spin or will not  
empty:  
the drain pipe is blocked or kinked,  
the drain filter is blocked,  
the anti-unbalance mass safety device has tripped; bad  
distribution of washing in the drum,  
the «Drain» program or the «Rinse hold» option is selected,  
the height of the drain siphon is wrong.  
There is water on the floor around the washing  
machine:  
excess detergent has made too much foam that over-  
flowed,  
the detergent is not suitable for washing machine,  
the drain siphon is not hooked on properly,  
the drain filter was not put back into place,  
the water inlet pipe is leaking.  
Washing results are not satisfactory:  
The machine is vibrating or noisy:  
the detergent is not suitable for machine washing,  
there is too much washing in the drum,  
the washing program is not appropriate,  
there is not enough detergent.  
not all the packing was removed from the machine (see  
unpacking section),  
the washing machine is not leveled and properly packed,  
the washing machine is too close to the wall or furniture,  
the washing is not well distributed in the drum,  
the load is not sufficient.  
The washing cycle is much too long :  
the water inlet is blocked,  
there was a power supply failure or the water was cut off,  
the motor temperature safety device tripped,  
the water inlet temperature is lower than normal,  
the foam detection safety system tripped (too much deter-  
gent) and the washing machine evacuated the foam,  
the anti-unbalance mass safety device tripped, an additio-  
nal phase was added to distribute the washing in the drum  
better.  
The washing machine stops during a washing cy-  
cle :  
the water or electricity supply is defective,  
a rinse hold was programmed.  
The cover does not open during the cycle :  
the «IMMEDIATE OPENING»* light is off,  
the temperature of the washing water is too high.  
the cover cannot open until 1 to 2 minutes after the  
washing machine has stopped*.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Symptom  
Cause  
The «DRUM POSITIONNING»* light** is not on at the  
end of the cycle:  
the drum could not reach the right position due to a persis-  
tent unbalanced mass; turn the drum manually.  
The «End»* light ** flashes 4 times***:  
The «End»* light ** flashes 2 times***:  
the cover is not correctly closed.  
the drain filter is blocked,  
the drain pipe is blocked or kinked,  
the drain pipe is too high (see «installation»),  
the drain pump is blocked,  
the installation siphon is blocked.  
The «End»* light ** flashes 1 time***:  
the water tap is closed,  
the water network has been cut off.  
Softener or Javel water flows through the over-  
flow orifice when filling* :  
you did not put in the right amount,  
the siphons at the back of the detergents dispenser are  
blocked.  
* Depending on the model.  
** Eliminate the causes of the failure if you find them, and then press on the «Start/Pause» pusbutton to restart the  
interrupted program.  
*** Depending on the model, some acoustic signals may be activated.  
8. AFTER SALES SERVICE  
If you have an operating problem, refer to the "Operating problems" section. If any work is necessary after you have  
made all your checks, please contact your washing machine dealer.  
When you call the After Sales Service, mention the model and product number of your washing machine, and its serial  
number. This information is given on the inside of the filter door and on the name plate at the back of the washing  
machine.  
If any work is done on your washing machine, insist that your After Sales Service uses manufacturer certified spare  
parts.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
B. FOR THE INSTALLER  
1. WARNINGS  
This washing machine is heavy. Take care when  
moving it.  
Please read the instructions in the "electrical con-  
nections" chapter carefully before connecting your  
washing machine.  
After installing your washing machine, make sure  
that it is not standing on its electrical power supply  
cable.  
When your machine is installed on a carpeted floor,  
make sure that the carpet does not close off the  
ventilation openings near the bottom of the  
machine.  
The power supply cable may be only replaced by  
the After Sales Service.  
You must remove the packing on the washing  
machine before use. Failure to remove all transport  
protection devices can cause damage to the  
washing machine or nearby furniture. The washing  
machine must be unplugged while packing is being  
removed.  
Do not allow any one other than a qualified plumber  
to make the hydraulic connections necessary to  
install your washing machine.  
The washing machine must be plugged in to a  
power outlet with a conform earth.  
Call a qualified electrician if the electrical installa-  
tion in your residence is such that you have to  
modify it before you can connect your washing  
machine.  
Your manufacturer cannot be held responsible for  
any damage resulting from a nonconform installa-  
tion.  
2. TECHNICAL CHARACTERISTICS  
DIMENSIONS  
Height  
Width  
Depth  
850 mm  
397 mm  
600 mm  
VOLTAGE / FREQUENCY  
TOTAL POWER  
230 V / 50 Hz  
2300 W  
WATER PRESSURE  
Minimum  
Maximum  
0,05 MPa (0,5 bar)  
0,8 MPa (8 bars)  
Type 20x27  
Connection to the water network  
This washing machine complies with CEE directive 89-336 about the limitation of radioelectric disturbances  
and directive CEE 73-23 for electrical safety.  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
If you want to keep your  
washing machine aligned with  
the adjacent furniture, you can  
cut the pipe support strip at the  
back of your washing machine.  
Leave the two side closers in  
place.  
3. INSTALLATION  
3.1. Unpacking  
Packing used to protect internal parts of  
the washing machine during transport  
must be removed before the washing  
machine is put into service for the first ti-  
me.  
3.2. Position  
Remove all packing from the  
washing machine. Tilt the  
washing machine sideways and  
then remove the packing under  
the motor, and straighten the  
washing machine.  
Put the washing machine on a flat hard floor in a well  
ventilated room.  
Make sure that your washing machine does not touch  
the wall or any other furniture in the room.  
3.3. Moving your washing machine  
If you want to move your  
washing machine, lift it onto its  
rollers by pulling the lever at the  
bottom of the washing machine  
all the way to the left. When you  
have put your washing machine  
into the required location, put  
the lever back into its initial  
position.  
Tilt the washing machine back-  
wards, rotate it by a quarter of a  
turn on one of its corner to re-  
move the transport base.  
Open the washing machine lid  
and remove the immobilization  
packing and plastic films.  
Close the lid.  
3.4. Leveling  
Precise leveling will prevent vibrations, noise and mo-  
vements of the washing machine during operation.  
Make the washing machine le-  
vel by adjusting the leveling  
screw that is too short.  
Unscrew the stand and locking  
collar assembly (lift the  
washing machine if necessary).  
Use a 10 mm spanner to remo-  
ve the two screws and spacers  
at the back.  
When the washing machine is  
stable, maintain the stand on  
the ground and turn the locking  
collar as far as posible.  
You can now see the openings  
that must be closed with the ca-  
ches in the pack attached to the  
washing machine; do not forget  
to fold down the central capsule.  
3.5. Water inlet  
Screw the supply ppe con-  
nector onto the water inlet tap  
(20x27 mm), remembering to  
use the washer provided with  
the washing machine.  
Make sure that you have remo-  
ved all these parts from your  
washing machine and keep  
them so that you can use them  
again if you need them for future  
transport.  
Open the water inlet tap.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
You cannot prolong the water inlet pipe. If it is too short,  
buy a longer pipe provided for this purpose.  
3.6. Drain  
The drain siphon must be pla-  
ced inside a drain pipe (or in a  
washbasin) at a height of  
between 70 and 100 cm. Make  
sure that it cannot fall.  
Important: the drain pipe must never be prolonged.  
If it is too short, call a professional.  
3.7. Electrical connection  
You can only connect this washing machine to 230 V  
single phase power supply.  
Check rating of the fuse line: 10 A at 230V.  
The washing machine must not be connected through  
an extension cable or a power bar.  
Check that the earthing connection is conform with the  
regulations in force.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
From the Electrolux Group. The world’s No.1 Choice.  
The Electrolux Group is the world largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group  
products (such as refrigerators, cookers, washing machines, vaccum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD  
14 billion in more than 150 countries around the world.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

West Bend Griddle L5749A User Manual
Westinghouse Power Hammer IL33 861 5 User Manual
Whirlpool Washer Front Loading Automatic Washer User Manual
Wind Crest Ventilation Hood WSL 304 User Manual
Wolfgang Puck Fryer BDFR0040 User Manual
Xerox Personal Computer V90 User Manual
Yakumo Two Way Radio PT18 User Manual
Yamaha Car Amplifier DSP AX563 User Manual
Zanussi Ventilation Hood 640033 User Manual
Zhone Technologies Network Card Network Device User Manual