WASHING MACHINE
F1045 W
F1245 W
F
1045W
AQUACYCLE 1000
C
D
A
MIXED FABRICS
H
ON-OFF
S
P
I
N
QUICK
WASH
HALF
LOAD
F
AST COLOUREDS
NON AST COLOUREDS
REDUCTION
F
WOOL CARE
DELICATES
WORN ONCE
FRESHEN UP
SHORT SPIN
DRAIN
L
M
J
WHITES
+
PREWASH
WHITES
HAND RINSES
LONG SPIN
B
F
N
K
P
G
GB
INSTRUCTION BOOKLET
132992240
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
For the User
For the Installer
Important Safety Information
2
4
Installation Instructions
Technical Specifications
21
21
Your New Washing Machine
Description of the Appliance
Detergent dispenser drawer
Child safety feature
5
5
5
Unpacking
Positioning
Water inlet
Water drainage
Levelling
Special conditions
In the interest of the environment
Electrical connection
22
22
23
23-24
24
The Control Panel
6
24
24
25
Operating sequence
7-10
7
Washing 4.5 kg of white cotton at 95°C
Load the laundry
7
Measure out the detergent
Measure out the fabric softener
Select the required option
Select the required programme
Start the machine
7
7
7
7
8
At the end of the programme
8
Washing 2 kg of mixed fabrics at 50°C
Load the laundry
9
9
Measure out the detergent
Measure out the fabric softener
Select the required option
Select the required programme
Start the machine
9
9
9
9
9
At the end of the programme
10
Washing Hints
Which detergent?....
And in which form?
11-12
12
12
Wash Care Symbols
Washing Programmes
13
14-15
Maintenance and Cleaning
16-17
16
Descaling
After each wash
16
Maintenance Wash
16
External cleaning
16
Cleaning the dispenser drawer
Cleaning the drawer recess
Cleaning the pump
16
16
16
The dangers of freezing
17
Something Not Working
Service and Spare Parts
Guarantee Conditions
18-19
19
20
Guide to use the Instruction Book
The following symbols will be found in the text to guide you throughout the instructions:
Safety instructions
Hints and tips
Environmental information
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Your New Washing Machine
Your new washing machine meets all modern requirements for effective treatment of laundry
with low water, energy and detergent consumption.
●
Automatic cooling of the wash water to 60°C
In the interest
before draining, with the 95°C programme. This
reduces thermal shock to fabrics, helping to prevent
creasing.
of the environment
●
Materials marked with the symbol
recyclable.
are
●
●
The special wool programme with its new delicate
wash system treats your woollens with extreme care.
●
●
Check with your local Council or Environmental
Health Office to see if there are facilities in your area
for re-cycling this appliance.
The ECO VALVE allows total use of detergent and
reduces water consumption so saving energy.
When the appliance is to be scrapped, cut off the
power supply cable and make the door lock device
unusable to prevent young children from being
trapped inside.
Ecological hints
To save water and energy and help protect the
environment, we recommend that you follow these
hints:
●
Help to keep your country tidy - use authorised
disposal sites for your old appliance.
●
Adjust the quantity of detergent according to the
hardness of your water supply, the amount of
laundry and the degree of soiling.
How do we help to protect the environment?
We use recycled paper!
●
A programme without prewash is sufficient for
normally soiled laundry.
●
The machine works more economically if it is fully
loaded.
●
With adequate pre-treatment, stains and limited
soiling can be removed; the laundry can then be
washed at a lower temperature, so saving energy.
Important
Your machine is fitted with a balance control de vice, which ensures the machine is stable during the spin.
If the wash load appears not to have been spun sufficiently at the end of the wash cycle, because it is not evenly
distributed in the drum, the balance control device may have operated. It will therefore be necessary to redistribute the
wash load manually and select a spin programme. For more detailed information see the section headed "Something
Not Working".
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the Appliance
1 Detergent dispenser drawer
2 Programme guide
3 “Mains-on” light
4 ON/OFF button
1
3
5
6
F
1
0
4
5
W
AQUACYCLE 1000
ON-OFF
S
P
I
N
QUICK
HALF
LOAD
C
D
A
MIXED FABRICS
H
FAST COLOUREDS
REDUCTION
WASH
NON FAST COLOUREDS
PREWASH
WOOL CARE
DELICATES
WORN ONCE
FRESHEN UP
SHORT SPIN
DRAIN
L
M
J
WHITES
+
WHITES
HAND RINSES
LONG SPIN
B
N
K
P
F
G
5 “Option” buttons
6 Programme selector dial
7 Door opening handle
8 Drain pump
24
7
9 Adjustable feet
8
9
Detergent dispenser drawer
Prewash
Main wash
Fabric softener
C0069
Child safety feature
This machine incorporates a special child safety feature
to prevent small children from being trapped inside the
machine.
To activate this device, rotate the button (without
pressing it) inside the door clockwise until the groove is
horizontal. If necessary use a coin.
To disable this device and restore the possibility of
closing the door, rotate the button anti-clockwise until
the groove is vertical.
P1131
5
Download from Www.Somanuals.com. All Manuals Search And Download.
The Control Panel
PROGRAMME
F
1045
W
AQUACYCLE 1000
ON-OFF
SPIN
REDUCTION
HALF
LOAD
QUICK
WASH
FAST COLOUREDS
NON FAST COLOUREDS
WHITES + PREWASH
WHITES
HAND RINSES
LONG SPIN
C
D
A
MIXED FABRICS
WOOL CARE
DELICATES
WORN ONCE
FRESHEN UP
SHORT SPIN
DRAIN
H
L
M
B
F
G
J
N
K
ZANUSSIQUALITY
P
1
2 3 4 5 6
7
1 Programme guide
2 On/Off button
5 QUICK WASH Button
By depressing this button on programmes A, B, C, D
and H the wash time is reduced.
This is suitable only for garments which are lightly
soiled.
By depressing this button the machine starts operating.
When depressed again, the machine stops.
6 HALF LOAD button
3 Mains-on light
Select this button to reduce water consumption on the
rinse cycle when washing a smaller load of cottons or
linens (maximum load size = 2.25 kg).
This light illuminates when the machine starts working
and goes out when the ON/OFF button is released.
4 Spin Reduction button
By depressing this button the spin speed is reduced as
follows:
7 Programme selector dial
Turn the dial clockwise to select the required wash
programme.
● cottons and linens: from 1000 rpm to 650 rpm for
model F1045W and from 1200 rpm to 650 rpm for
model F1245W.
Before setting the dial to any position the machine must
be switched off by depressing the ON/OFF button
again.
● synthetics, delicates and wool (programme “K”):
from 650 rpm to 450 rpm.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Operating Sequence
Before the first wash, we recommend that you pour 2
3. Measure out the fabric
softener
litres of water into the main wash compartment
of
the detergent drawer in order to activate the ECO valve.
Then run a cotton cycle at 60°C, without any laundry in
the machine, to remove any manufacturing residue from
the drum and tub.
Pour 1/2 a measure of detergent into the dispenser
drawer and start the machine.
If required, pour fabric softener into the compartment
marked
(the amount used must not exceed the
“MAX” mark in the drawer).
Close the drawer gently.
WASHING 4.5 KG OF WHITE COTTON AT 95°C
Suppose you have 4.5 kg of normally soiled laundry to
wash. It is white cotton and is suitable for high
temperature washing.
C0071
1. Load the laundry
Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
4. Select the required option
Depress QUICK WASH button or SPIN REDUCTION
if required .
SPIN
REDUCTION
HALF
LOAD
QUICK
WASH
P0004
2. Measure out the detergent
5. Select the required programme
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
Turn the programme selector dial clockwise to the
programme B or A (if you wish to perform a prewash).
it into the main wash compartment
.
If you wish to carry out the prewash, pour detergent into
the compartment marked
.
B
P1006S
C0070
7
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Start the machine
Before starting up the machine check that:
●
the appliance is plugged in
●
the water supply taps are turned on
●
the drain hose is correctly and securely positioned
●
the door and the detergent dispenser drawer are
closed.
Depress the ON/OFF button: the mains-on light will
illuminate and the machine starts operating.
ON
OFF
T0001S
7. At the end of the programme
The machine stops automatically.
The door is controlled by a safety device which releases
2 minutes after the end of the programme.
Switch the machine off by depressing the ON/OFF
button again. The mains-on light goes out.
When the programme has finished you are advised to
unplug the appliance and turn off the water taps.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WASHING 2 KG OF MIXED FABRICS AT 50°C
Suppose you have 2 kg of Mixed fabrics to wash. They
are rather delicate fabrics and should not be washed at a
high temperature.
4. Select the required option
Depress the QUICK WASH or SPIN REDUCTION
button if required.
1. Load the laundry
Open the door by pulling the door handle outwards.
Place the laundry in the drum, one item at a time,
shaking them out as much as possible. Close the door.
SPIN
REDUCTION
HALF
LOAD
QUICK
WASH
5. Select the required programme
Turn the programme selector dial clockwise to the
programme H.
P0004
H
2. Measure out the detergent
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required and pour
it into the main wash compartment
.
M0017S
6. Start the machine
Before starting up the machine check that:
●
the appliance is plugged in
C0070
●
the water supply taps are turned on
3. Measure out the fabric
softener
●
the drain hose is correctly and securely positioned
●
the door and the detergent dispenser drawer are
closed.
If required, pour fabric softener into the compartment
Depress the ON/OFF button: the mains-on light will
illuminate and the machine starts operating.
marked
“MAX” mark in the drawer).
Close the drawer gently.
(the amount used must not exceed the
ON
OFF
T0001S
C0071
9
Download from Www.Somanuals.com. All Manuals Search And Download.
7. At the end of the programme
After the last rinse, the machine stops with the water left
in the wash tub, to prevent the fabric from creasing.
To drain the water, select programme “K” (short spin)
or “P” (drain).
The door is controlled by a safety device which releases
2 minutes after the end of the programme.
Switch the machine off by depressing the ON/OFF
button again. The mains-on light goes out.
When the programme has finished you are advised to
unplug the appliance and turn off the water taps.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Hints
●
●
●
Do NOT overload the machine. Weigh the laundry the
For wool, use gentle detergent only in small
quantities.
first few times you use the appliance.
Bleach is very corrosive; it should be used with care
and kept out of reach of children.
The average weights of the most common items are
listed below as a guide:
Some stains such as fruit, wine, grass, rust etc. are
difficult to remove and should be treated before
washing with specific products, which can be found
in most household shops. In some cases it may help
to soak the stain before washing with a special pre-
soak product or biological detergent.
1000g = 1 kg
Sheet
700-1000 g
100-200 g
400-500 g
50-100 g
Pillow case
Tablecloth
●
●
Only wool marked “Pure New Wool - washable,
preshrunk” can be washed in the machine using the
wool programme; other types of wool should be
washed by hand or dry cleaned.
Serviette
Tea towel
70-120 g
Linen hand towel
Towelling hand towel
Towelling bath towel
Bath robe
100-150 g
150-250 g
700-1000 g
1000-1500 g
200-300 g
150-200 g
If you have used the machine to wash, rinse or spin
only non-colour fast garments, there may be dye left
in the sump. To ensure any subsequent wash is not
contaminated with the dye, select and carry out a
rinse and spin programme, without any garments, to
ensure that any dye is removed from the sump.
Man’s shirt
Apron
●
Once you have finished using the machine, you are
advised to unplug it and turn off the water taps.
●
Load the laundry loosely alternating large items with
small ones.
●
●
●
Sort the laundry according to the type of fabric,
colour-fastness and how dirty it is.
Avoid washing unhemmed or torn items as they may
unravel.
Before washing, empty all pockets of small objects
which may have been left inside (coins, keys, screws
etc). as these could damage the drain pump.
●
●
●
When washing curtains, remove the hooks.
Close poppers and zips and fasten loose buttons.
It is essential to wash new coloured items separately
when washing for the first time.
●
When washing fabrics requiring different wash
temperatures together, always select the lowest
temperature.
●
●
●
●
White items should not be washed with coloured
items.
Very small items (handkerchiefs, ribbons, socks etc)
should be washed in a washing bag or a pillow case.
Use a good quality detergent suitable for automatic
washing machines.
Use the correct quantities of detergent.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
And in which form?
Not only are there different types of detergent, but they
are also available in different forms. Whether you chose
a powder or liquid in traditional or compact form is
your own personal choice.
Which detergent?....
To ensure you obtain the best wash results from your
appliance, it is important to use the right detergent in
your everyday wash, and only detergents recommended
for use in automatic machines.
To maintain the appearance of your clothes and
household textiles and to make them last longer you
should use different types of detergent for different
washes, whether for whites, colours or delicates.
TRADITIONAL POWDERS
Pour the powder directly into the dispenser drawer. Do
not sprinkle powder onto clothes in the machine drum.
TRADITIONAL LIQUIDS
Liquid can be placed in the main wash compartment of
the detergent drawer marked with the symbol
the machine immediately upon placing the detergent in
the dispenser drawer.
Alternatively the detergent is measured into the
specially designed dosing device* which should be
placed on top of the laundry, and at the back of the
machine drum.
WHITES
We recommend the Ariel product
range which is biological and
designed to provide excellent
cleaning and stain removal even
at low temperatures.
, start
NON BIOLOGICAL
If you prefer to use a non
biological detergent, which does
not contain enzymes we
recommend Fairy. Fairy provides
good cleaning and stain removal.
COMPACT POWDERS AND LIQUIDS
Compact detergents (or concentrates as they are also
known) are available in liquid or powder form, and
generally require a smaller dosage. Follow the
manufacturer’s instructions to ensure the most
economical usage. Pour the detergent directly into the
dispenser drawer, or alternatively measure the detergent
into the specially designed dosing device* which
should be placed on top of the laundry, and at the back
of the machine drum.
COLOUREDS
For coloured items you should use a
detergent which is designed to clean
while maintaining the original colour.
Ariel Color does not contain bleach
and therefore helps to preserve
colours.
* If you use a dosing device in a washer dryer,
please ensure the dosing device/ball is removed
before carrying out a drying programme.
DELICATE ITEMS
FABRIC CONDITIONERS
These are ideal for improving ‘softness’, and also
reduce static cling on synthetics and make ironing
easier. They are available in two types:
When washing delicates such as
woollens, you should use a product
which is specially designed to care for
fine fabrics.
Dreft Automatic is suitable for
woollens and other delicates.
For example Lenor liquid fabric
softener, for use in the washing
machine/washer dryer. The
liquid fabric softener should be
poured into the compartment
LAUNDRY BLEACH
For additional stain removal you may
wish to use a product such as Ace
Gentle Bleach which is used in addition
to your chosen detergent. Ace is
suitable for all washable fabrics
including silks, woollens and coloureds.
marked with the symbol
.
Follow the manufacturer’s dosage
instructions and never exceed the
MAX level.
Bounce conditioning sheets for use
in a tumble dryer. We recommend
the conditioning sheets are pinned
(using a safety pin) to an article
of laundry and placed in the
tumble dryer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Wash Care Symbols
Wash care labels inside garments recommend how to launder your clothes with the best results. The care labelling
code is in line with care labelling used in the rest of Europe. The symbols used make it easy to select the correct
programme on your washing machine.
WASHING SYMBOL
WASH ACTION
Normal (Maximum)
Normal (Maximum)
FABRIC
White Cotton or Linen
without Special Finishes
95
Cotton, Linen or Viscose
without Special Finishes
Colourfast at 60°C.
60
50
Nylon, Polyester/Cotton, Viscose
with Special Finishes,
Cotton/Acrylic Mix.
Reduced (Medium)
Normal (Maximum)
Reduced (Medium)
Cotton, Linen or Viscose
Colourfast at 40°C but not 60°C.
40
40
Acrylics, Acetate, Triacetate, Wool
mixes, Polyester/wool blends.
Wool, wool mixtures, Silks
Do not machine wash
40
Much Reduced (Minimum)
Hand wash only
BLEACHING
Chlorine bleach may be used
IRONING
Cotton, Linen, Viscose
Polyester mixtures, Wool
Acrylic, Nylon, Polyester
Hot iron
Warm iron
Cool iron
DRY CLEANING
May be dry cleaned. Other letters and/or a bar beneath the circle will
indicate the required process to the dry cleaner.
TUMBLE DRYING
with high heat setting
with low heat setting
May be tumble dried
A cross through any symbol means «DO NOT»
X
Important Notes
For best results, always use the dispenser drawer for
dispensing detergents and liquid additives.
Once the dispenser has been filled, close it by pushing it
in gently. This is particularly important if you are using
fabric conditioner to avoid the conditioner entering the
machine prematurely.
When using liquid detergent and a prewash programme,
place the detergent into the correct compartment in the
dispenser drawer, after the prewash has finished.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Programmes
Programmes for cotton and linen
Progr.
time
mins.
Wash programme/
Washing symbol
Degree of soil
and type of laundry
Programme
dial position
Possible
options
Max
Load
Description
Prewash at 40 °C
Wash at 95°C
3 rinses
WHITES
+
PREWASH
QUICK WASH
HALF LOAD
SPIN RED.
For heavy soiled cotton
items.
145
4.5 kg
A
Long spin
White cotton, for
example normally soiled
work garments, sheets,
household linen,
Wash at 95 °C
3 rinses
Long spin
QUICK WASH
HALF LOAD
SPIN RED.
WHITES
4.5 kg
4.5 kg
120
130
B
C(*)
D
underwear, towels.
Wash at 60 °C
3 rinses
Long spin
Fast coloured cotton or
linen fabrics, shirts,
underwear, towels.
QUICK WASH
HALF LOAD
SPIN RED.
FAST
COLOUREDS
Non fast coloured
cotton or linen fabrics,
shirts, blouses,
Wash at 40 °C
3 rinses
Long spin
QUICK WASH
HALF LOAD
SPIN RED.
NON- FAST
COLOUREDS
4.5 kg 115
underwear.
Separate rinse cycle for
hand washed cotton
and linen items
HAND
RINSES
4 rinses
Long spin
F
SPIN RED. 4.5 kg 58
Separate spin for
cotton and linen items
LONG SPIN
12
Long spin
SPIN RED. 4.5 kg
G
(*) This programme at 60°C with cold water filling and a wash load of 4.5 kg is the reference programme for the
Energy label according to EEC Directive 92/75.
Water filling:
30°-40° programmes: cold water filling
50°-60° programmes: hot and cold filling
95° programme: hot water filling
The programme times are intended as a guide only. The actual time will vary depending on incoming water
temperature and pressure.
Important!
●
Some programmes when selected may start with a short drain. This is quite normal and not a fault with the
appliance.
When a programme is selected, the selector dial will advance to the water filling position. E.g. Programme B is
selected, there is a short drain. The appliance takes in water and the selector will appear to move to the C position.
The appliance will have memorised the programme selected, in this case B, and will run the correct programme
even though the selector dial appears to be at position C.
●
We recommend you not to switch the appliance off and on during its operation. This would modify the memorised
programme in progress with unsatisfactory washing results.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Washing Programmes
Programmes for synthetics, mixed fabrics, delicates and wool
Progr.
time
mins.
Wash programme/
Washing symbol
Degree of soil
and type of laundry
Programme
dial position
Possible
options
Max
Load
Description
Synthetic or mixed
fabrics, underwear,
coloured garments,
non-shrink shirts,
blouses.
Wash at 50 °C
3 rinses
Stop with water in
tub
QUICK WASH
MIXED
FABRICS
2 kg
60
H
Wash at 30 °C
3 rinses
Stop with water in
tub
WORN
ONCE
Lightly soiled synthetic
or mixed fabrics
2 kg
2 kg
30
6
J
Separate spin for hand
washed delicate items
Draining of water
and short spin
SHORT
SPIN
SPIN RED.
K
Specially tested
programme for wool
garments bearing the
“Pure new wool, non-
shrink, machine
Wash at 40 °C
3 rinses
Stop with water in
tub
WOOL CARE
DELICATES
1 kg
50
L
washable” label.
Wash at 40 °C
3 rinses
Stop with water in
tub
Delicate fabrics, for
example curtains
M
2 kg
2 kg
-
45
9
1 rinse, with fabric
softener, if required
Stop with water in
tub
This programme can be
used for softening hand
washed garments.
FRESHEN UP
DRAIN
N
P
For emptying out the
last rinse water of these
programmes
1
Draining of water
Important!
●
Some programmes when selected may start with a short drain. This is quite normal and not a fault with the
appliance.
When a programme is selected, the selector dial will advance to the water filling position.
●
We recommend you not to switch the appliance off and on during its operation. This would modify the memorised
programme in progress with unsatisfactory washing results.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Cleaning
Before any maintenance or cleaning is carried out you
must DISCONNECT the appliance from the electricity
supply.
Descaling
The water we use normally contains lime. It is a good
idea to periodically use a water softening powder in the
C0073
C0072
machine. Do this separately from any laundry washing,
and according to the softening powder manufacturer's
instructions. This will help to prevent the formation of
lime deposits.
Cleaning the drawer recess
Having removed the drawer, use a small brush to clean
the recess, ensuring that all washing powder residue is
removed from the upper and lower part of the recess.
Replace the drawer and run the rinse programme
without any clothes in the drum.
After each wash
Leave the door open for a while. This helps to prevent
mould and stagnant smells forming inside the appliance.
Keeping the door open after a wash will also help to
preserve the door seal.
Maintenance Wash
With the use of low temperature washes it is possible to
get a build up of residues inside the drum.
We recommend that a maintenance wash be performed
on a regular basis.
P0038
Cleaning the pump
The pump should be inspected if
To run a maintenance wash:
●
The drum should be empty of laundry.
●
Select the hottest cotton wash programme.
• the machine does not empty and/or spin
• the machine makes an unusual noise during draining
due to objects such as safety pins, coins etc. blocking
the pump.
●
Use a normal measure of detergent, must be a
powder (such as Ariel Futur).
Proceed as follows:
External cleaning
Clean the exterior cabinet of the appliance with soap
and water only, and then dry thoroughly.
• Disconnect the appliance.
• If necessary wait until the water has cooled down.
• Open the pump door.
Cleaning the dispenser drawer
The washing powder and additive dispenser drawer
should be cleaned regularly.
Remove the drawer by pressing the catch downwards
and by pulling it out. Flush it out under a tap, to remove
any traces of accumulated powder.
To aid cleaning, the top part of the additive
compartment should be removed.
P1114
• Place a container close to the pump to collect any
spillage.
• Pull out the emergency emptying hose, place it in the
container and remove its cap.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
• When no more water comes out, unscrew the pump
cover and remove it. Always keep a rag nearby to dry
up spillage of water when removing the cover.
Clean the filters using a hard bristle brush.
Tighten up the inlet hoses.
P1090
P1115
The dangers of freezing
• Remove any objects from the pump impeller by
rotating it.
If the machine is exposed to temperatures below 0°C,
certain precautions should be taken.
●
Turn off the water taps.
●
Unscrew the inlet hoses.
●
Place the end of the emergency emptying hose and
that of the inlet hoses in a bowl placed on the floor
and let water drain out.
●
Screw the water inlet hoses back on and reposition
the emergency emptying hose after having put the
cap on again.
• Put the cap back on the emergency emptying hose and
place the latter back in its seat.
●
When you intend to start the machine up again,
make sure that the room temperature is above 0°C.
Important!
Every time you drain the water through the emergency
emptying hose you must pour 2 litres of water into the
main wash compartment of the detergent drawer and
then run the drain programme. This will activate the
ECO valve avoiding that part of the detergent remains
unused at next washing.
P1117
• Screw the pump cover fully in.
• Close the pump door.
Emergency emptying out
If the water is not discharged, proceed as follows to
empty out the machine:
Warning
When the appliance is in use and depending on the
programme selected there can be hot water in the pump
circuit. Never remove the pump cover during a wash
cycle, always wait until the appliance has finished the
cycle, and is empty. When replacing the pump cover,
after a cleaning inspection, ensure it is securely
retightened so as to stop leaks and young children being
able to remove it.
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled down;
• open the pump door;
• place a bowl on the floor and place the end of the
emergency emptying hose into the bowl. Remove its
cap. The water should drain by gravity into the bowl.
When the bowl is full, put the cap back on the hose.
Empty the bowl. Repeat the procedure until water
stops flowing out;
Cleaning the water inlet filters
If your water is very hard or contains traces of lime
deposit, the water inlet filters may become clogged.
• clean the pump if necessary as previously described;
• replace the emergency emptying hose in its seat after
having plugged it;
• screw the pump cover again and close the door.
It is therefore a good idea to clean it from time to time.
Turn off the water taps. Unscrew the water inlet hoses.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out
an engineer. Before contacting your local Service Force Centre, please carry out the checks listed below.
IMPORTANT: if you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or
installation, a charge will be made even if the appliance is under guarantee.
Symptom
Possible causes
●
The machine does not start
The door has not been closed.
The plug is not properly inserted in the power socket.
There is no supply at the socket
The main fuse or the fuse in the plug has blown.
The selector dial is not correctly positioned.
The ON/OFF button has not been depressed.
●
●
●
●
●
●
The machine does not fill
Ensure the water taps are open.
The filters in the inlet hoses are blocked.
The inlet hoses may be squashed or kinked.
The door has not been closed.
●
●
●
●
The machine fills then empties
immediately
The end of the drain hose is too low.
The end of the drain hose is submerged in water.
There is no vent in the end of the drain hose.
●
●
●
The machine does not empty and/or
does not spin
The drain hose may be squashed or kinked.
The drain pump may be blocked.
The drain hose extension, if fitted, is not correct. Follow the
●
●
instructions for connecting to the waste.
The drainage system pipes are blocked.
●
The wash load is unbalanced: redistribute the clothes inside the drum to
allow the machine to spin.
A programme which ends with water in tub has been selected.
●
●
There is water on the floor
Too much detergent or unsuitable detergent has been used (creates too
much foam).
●
Check whether there are any leaks from one of the inlet hose(s) fittings.
It is not always easy to see this as the water runs down the hose; check
to see if it is damp.
The drain hose may be damaged or not securely positioned.
The detergent dispenser drawer or recess is clogged.
The drainage system pipes are blocked.
●
●
●
●
Unsatisfactory washing results
Too little detergent or unsuitable detergent has been used. An
insufficient amount of detergent leaves the laundry looking grey and
causes lime scale to form.
Stubborn stains have not been treated prior to washing
The correct wash programme has not been selected.
Too much laundry has been placed in the drum.
●
●
●
●
The machine vibrates when spinning
The internal packing has not been removed.
The machine is in contact with the wall or furniture.
The machine is not stable and level (check diagonally).
The washing load is badly distributed in the drum.
●
●
●
●
Maybe there is very little laundry in the drum.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Symptom
Possible causes
●
The programme is still running.
The door lock has not yet released.
Water in the tub: the door cannot be opened if water is present in the
The door will not open
●
●
tub.
●
The electronic unbalance detection device has cut in because the
Spinning starts late or the machine
does not spin
laundry is not evenly distributed in the drum. The laundry is
redistributed by reverse rotation of the drum. This may happen several
times before the unbalance disappears and normal spinning can resume.
If, after 10 minutes, the laundry is still not evenly distributed in the
drum, the machine will not spin. In this case, redistribute the load
manually and reselect the spin programme.
●
The machine makes an unusual
noise
The machine is fitted with a type of motor which makes an unusual
noise compared with other traditional motors. This new motor ensures
a softer start and more even distribution of the laundry in the drum
when spinning, as well as increased stability of the machine.
●
No water is visible in the drum
Machines based on modern technology operate very economically
using very little water without affecting performance.
Service & Spare Parts
In the event of your appliance requiring service, or if
you wish to purchase spare parts, please contact your
local Service Force Centre by telephoning:
P
r
M
o
d
o
d
.
N
.
.
.
o
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
S
.
.
e
.
.
r
.
.
N
o
.
.
.
.
.
.
.
.
.
.
0870 5 929929
Your telephone call will be automatically routed to the
Service Force Centre covering your post code area.
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042 BD
For the address of your local Service Force Centre and
further information about Service Force, please visit the
Before calling out an engineer, please ensure you have
read the details under the heading “Something Not
Working”.
Customer Care Department
For general enquiries concerning your Zanussi
Electrolux appliance or for further information on
Zanussi Electrolux products, please contact our
Customer Care Department by letter or telephone at the
When you contact the Service Force Centre you will
need to give the following details:
1. Your name, address and post code
2. Your telephone number
3. Clear and concise details of fault
4. The model and serial number of the appliance (found
on the rating plate - see picture)
Customer Care Department
Zanussi Electrolux
55-77 High Street
Slough
Berkshire
5. The purchase date.
SL1 1DZ
Please note that a valid purchase receipt or
guarantee documentation is required for in-
guarantee service calls.
Tel 08705 727727*
* calls to this number may be recorded for training
purposes.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Guarantee Conditions
Standard guarantee conditions
Exclusions
We, Zanussi Electrolux, undertake that if, within 12
months of the date of the purchase, this ZANUSSI
ELECTROLUX appliance or any part thereof is proved
to be defective by reason only of faulty workmanship or
materials, we will, at our option repair or replace the
same FREE OF ANY CHARGE for labour, materials or
carriage on condition that:
This guarantee does not cover:
●
Damage or calls resulting from transportation,
improper use or neglect, the replacement of any light
bulbs or removable parts of glass or plastic.
●
Costs incurred for calls to put right an appliance
which is improperly installed or calls to appliances
outside the United Kingdom.
●
The appliance has been correctly installed and used
●
Appliances found to be in use within a commercial
only on the electricity supply stated on the rating
plate.
environment, plus those which are subject to rental
agreements.
●
The appliance has been used for normal domestic
●
Products of Zanussi Electrolux manufacture which
purposes only, and in accordance with the
manufacturer’s instructions.
are NOT marketed by Zanussi Electrolux.
●
The appliance has not been serviced, maintained,
repaired, taken apart or tampered with, by any
person not authorised by us.
European guarantee
If you should move to another country within Europe
then your guarantee moves with you to your new home
subject to the following qualifications:
●
All service work under this guarantee must be
undertaken by a Service Force Centre.
●
Any appliance or defective part replaced shall
become the Company’s property.
The guarantee starts from the date you first
●
purchased your product.
●
This guarantee is in addition to your statutory and
other legal rights.
The guarantee is for the same period and to the same
●
extent for labour and parts as exists in the new
country of use for this brand or range of products.
Home visits are made between 8.30am and 5.30pm
Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
The guarantee relates to you and cannot be
●
transferred to another user.
Your new home is within the European Community
●
(EC) or European Free Trade Area.
The product is installed and used in accordance with
●
our instructions and is only used domestically, i.e. a
normal household.
The product is installed taking into account
●
regulations in your new country.
Before you move please contact your nearest Customer
Care Centre, listed below, to give them details of your
new home. They will then ensure that the local Service
Organisation is aware of your move and able to look
after you and your appliances.
France
Germany
Italy
Senlis
+33 (0) 344 62 29 29
+49 (0) 800 234 7378
+39 0434 39 4700
Nurnberg
Pordenone
Stockholm
Slough
Sweden
UK
+46 (0) 8 672 53 90
+44 (0) 1753 219897
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Care must be taken to ensure that the appliance
does not stand on the electrical supply cable.
Any electrical work required to install this
appliance should be carried out by a qualified
electrician or competent person.
Any plumbing work required to install this
appliance should be carried out by a qualified
plumber or competent person.
Should the appliance power supply cable need to
be replaced, this should be carried out by our
Service Force Centre.
Technical Specifications
DIMENSIONS
Height
Width
Depth
85 cm
60 cm
57 cm
POWER SUPPLY VOLTAGE
TOTAL POWER ABSORBED
230-240 V/50 Hz
2050 W (10A)
WATER PRESSURE
Minimum (hot)
Minimum
35 kPa
50 kPa
Maximum
800 kPa
MAXIMUM RECOMMENDED LOAD
Cotton, linen
Synthetics
Delicate fabrics
Wool
4.5 kg
2 kg
2 kg
1 kg
SPIN SPEED
Maximum
1000 rpm (F1045W)
1200 rpm (F1245W)
CONSUMPTION DATA FOR WASHING
4.5 KG NORMALLY SOILED COTTON
ITEMS AT 60°C (PROGR. C) WITH COLD
WATER FILLING
Energy
Water
0.85 kWh
53 litres
This appliance complies with the following E.E.C. Directives:
- 73/23 EEC of 19.2.73 (Low Voltage Directive) and subsequent modifications;
- 89/336 EEC of 3.5.89 (Electromagnetic Compatibility Directive) and subsequent modifications.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Fill all the holes with the plastic plugs supplied with the
instruction booklet.
Unpacking
All transit bolts and packing must be removed
before using the appliance.
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
Using a spanner unscrew and remove the two rear
bottom screws. Slide out the two plastic pins.
P1128
P0002
Lay the machine gently on its back, making sure that the
hoses are not squashed.
Important !
You are advised to keep all the packaging for re-use in
case the machine is to be transported again.
If the appliance is to be moved, the precautions listed
under “The dangers of freezing” must be carried out
i.e. the residual water in the hoses must be pumped out.
P0001
P1129
Positioning
Install the machine on a flat hard floor.
Remove the polystyrene block from the bottom of the
machine and release the two plastic bags.
Very carefully slide out the left polythene bag, removing
it towards the right and then downwards.
Make sure that air circulation around the machine is not
impeded by carpets, rugs etc. Check that the machine
does not touch the wall or other kitchen units.
Never place cardboard, wood or similar materials under
the machine to compensate for any unevenness in the
floor.
1
2
Your new washing machine has been designed to be
permanently plumbed in to your home’s water supply
and drainage system. However, if this is not possible, it
may be connected to suitable existing taps with the drain
hose discharging into a sink.
3
P1124
P1126
The appliance has two inlet hoses, hot and cold, with
female 3/4” BSP thread connectors. If this connection is
not compatible with the plumbing of the existing
installation, a variety of connectors are available from
good hardware stores and plumbers merchants to suit
most domestic plumbing. Any alteration to your existing
plumbing must be carried out by a competent person, or
qualified plumber.
Repeat the operation for the right polythene bag,
removing it towards the left and then upwards.
Installation on a Suspended Floor
P1127
Suspended wooden floors are particularly susceptible to
vibration. To help prevent vibration we recommend you
place a waterproof wood panel, at least 15 mm thick
under the appliance, secured to at least 2 floor beams
with screws. If possible install the appliance in one of
the corners of the room, where the floor is more stable.
Remove the polystyrene base.
Set the machine upright and unscrew the remaining rear
screw. Slide out the relevant pin.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Water inlet
The inlets on the back of the appliance are colour coded,
blue for cold and red for hot.
Water drainage
This appliance is designed to be permanently plumbed
into your home's water supply and drainage system.
Connect the hoses to a tap with a 3/4” thread.
Do not use already employed inlet hoses.
The appliance drain hose should hook into a standpipe,
the hook in the drain hose is formed using the plastic
“U-Piece” supplied.
The standpipe should have an internal diameter of
approximately 38mm (see diagram) thus ensuring there
is an air break between the drain hose and standpipe.
1
38 mm.(1/2") diameter
standpipe
P1088
If only a cold water supply is available, connect the two
hoses to a cold water outlet by means of a «Y»
connection piece.
P1040
Installation should comply with local water authority
and building regulations’ requirements.
When discharging into a standpipe ensure that the top of
the curve in the hose end is no more than 90cm (35.4'')
and no less than 60cm (23.6'') above floor level. The
upright standpipe should have a minimum length of
30cm (12'') from the bottom of the elbow to the top of
the pipe (see diagram).
The appliance must be given a separate cold water
supply and not be connected to a mixer tap, a single
outlet water heater or a booster pump. A minimum
water pressure of 0.48 bar is required for safe operation
of the appliance.
If you cannot make the cold water connection direct
from the rising mains, you may be able to operate the
appliance from your cold water storage system.
3 pin
There should be a minimum distance of 5.02m
(16.5 ft) between the appliance’s inlet and the bottom of
the water storage tank.
There will be sufficient pressure for the hot water
supply, providing there is a minimun height of 2.74
metres (9 ft) between the bottom of the cold water
storage tank and the bottom of the hot water cylinder.
P1130
Make sure that it is designed in such a way, that the end
of the drain hose cannot be covered with water.
Set the hoses correctly by loosening the ring nuts. After
positioning the inlet hoses, be sure to tighten the ring
nuts again to prevent leaks.
The drain hose may be extended to a maximum of 4
metres. An additional drain hose and joining piece
is available from your local Service Force Centre.
The joining piece must have an internal diameter of
18mm.
P0021
23
Download from Www.Somanuals.com. All Manuals Search And Download.
If you intend the drain hose to empty into a sink, make
sure that the sink is empty and the plug hole is not
blocked. Use the plastic “U-Piece” supplied.
Special conditions
If the floor is carpeted or covered with crumbly or soft
material, insert a rigid support base under the feet to
prevent noise, vibration or displacement. The base
should protrude a few centimetres beyond the edges of
the machine.
Warning
The machine should NOT be placed on deep pile
carpeting.
P0022
Note
Please ensure that when the appliance is installed it is
easily accessible for the engineer in the event of a
breakdown.
The drain hose must not be kinked.
Important
●
Before connecting up the machine to new pipework
or to pipework that has not been used for some time,
run off a reasonable amount of water to flush out any
debris that may have collected in the pipes.
For a correct functioning of the machine the drain
hose must be hooked on the proper support piece
situated on the top of the back side of the appliance.
In the interest of the
environment
Washing machines and dishwashers should be
connected to the FOUL drainage system, the water will
then be taken to a sewage works for treatment before
being discharged safely into a river.
●
It is essential that these appliances are not connected to
the surface water drainage system as this water is
discharged directly into a river or stream and may cause
pollution. If you require any further advice please
contact your local water authority.
Levelling
Level the washing machine by raising or lowering the
feet. The feet may be tight to adjust as they incorporate
a self locking nut, but the machine MUST be level and
stable.
P1051
SHOWER
SINK TOILET
Any necessary adjustment can be made with a spanner.
Accurate levelling prevents vibration, noise and
displacement of the machine during operation.
BATH
BIDET
Some vibration is inevitable, especially if mounted on a
wooden floor.
WASHING
MACHINE
DISHWASHER
RAINWATER
'RUN-OFF'
Sprung wooden floors are particularly susceptible to
vibration. For advice, consult a builder. If possible,
always place the machine on a solid floor.
FOUL DRAIN
SURFACE WATER
DRAINS & SEWERS
FOUL SEWERS
SEWAGE
TREATMENT
WORKS
UNTREATED
DISCHARGE
TREATED
DISCHARGE
RIVER
RIVER
P0987
24
Download from Www.Somanuals.com. All Manuals Search And Download.
The wire coloured brown must be connected to the
terminal marked «L» or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure over
the outer sheath.
Electrical connection
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
WARNING: THIS APPLIANCE MUST BE
EARTHED.
WARNING:
A cut off plug inserted into a 13 amp socket is
a serious safety (shock) hazard.
Ensure that the cut off plug is disposed of
safely.
The manufacturer declines any liability should
this safety measure not be observed.
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance’s
rating plate. The rating plate is located at the top of the
rim of the open door.
Should the appliance power supply cable neeed to be
replaced, this should be carried out by our Service
Force Centre.
Note
When the appliance is installed the power supply cable
must be accessible.
P
r
M
o
d
o
d
.
N
.
.
.
o
.
.
.
.
.
.
.
.
.
.
.
.
.
.
.
S
.
.
e
.
.
r
.
.
N
o
.
.
.
.
.
.
.
.
.
.
Permanent connection
Mod. ..........
Prod. No. ...........
Ser. No. .........
P0042 BD
In the case of permanent connection it is necessary that
you install a double pole switch between the appliance
and the electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a type
suitable for the required load in compliance with the
current electrical regulations.
The appliance is supplied with a 13amp plug fitted.
In the event of having to change the fuse in the plug
supplied, a 13amp ASTA approved (BS1363A) fuse
must be used.
Should the plug need to be replaced for any reason,
proceed as described below.
The switch must not break the yellow and green earth
cable at any point.
The wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
Blue
- Earth
- Neutral
- Live
Brown
GREEN & YELLOW
E
L
N
BROWN
BLUE
CORD CLAMP
P1041
The wire coloured green and yellow must be connected
to the terminal marked with the letter «E» or by the
earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the
terminal marked «N» or coloured black.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
From the Electrolux Group. The world’s No. 1 choice.
The Electrolux Group is the world's largest producer of powered appliances for kitchen, cleaning and outdoor use.
More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners,
chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries
around the world.
© Electrolux plc 2003
Download from Www.Somanuals.com. All Manuals Search And Download.
|