User
manual
Washer-
dryer
ZKH 2105
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety information
In the interest of your safety and to ensure
the correct use, before installing and first
using the appliance, read this user manual
carefully, including its hints and warnings.
To avoid unnecessary mistakes and
accidents, it is important to ensure that all
people using the appliance are thoroughly
familiar with its operation and safety
features. Save these instructions and make
sure that they remain with the appliance if it
is moved or sold, so that everyone using it
through its life will be properly informed on
appliance use and safety.
● Always unplug the appliance and turn off the
water supply after use, clean and
maintenance.
● Under no circumstances should you attempt
to repair the machine yourself. Repairs
carried out by inexperienced persons may
cause injury or serious malfunctioning.
Contact your local Service Centre. Always
insist on genuine spare parts.
Installation
● This appliance is heavy. Care should be
taken when moving it.
● When unpacking the appliance, check that it
is not damaged. If in doubt, do not use it and
contact the Service Centre.
● All packing and transit bolts must be
removed before use. Serious damage can
occur to the product and to property if this is
not adhered to. See relevant section in the
user manual.
● After having installed the appliance, check
that it is not standing on the inlet and drain
hose and the worktop is not pressing the
electrical supply cable.
● If the machine is situated on a carpeted floor,
please adjust the feet in order to allow air to
circulate freely.
General safety
● It is dangerous to alter the specifications or
attempt to modify this product in any way.
● During high temperature washing and drying
programmes the door glass may get hot. Do
not touch it!
● Make sure that small pets do not climb into
the drum. To avoid this, please check into
the drum before using.
● Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp
material can cause extensive damage and
must not be placed into the machine.
● Only use the advised quantities of fabric
softener and detergent. Damage to the fabric ● Always be sure, that there is no water
can ensue if you over-fill. Refer to the
manufacturer’s recommendations of
quantities.
● Wash small items such as socks, laces,
washable belts etc in a washing bag or
pillow case as it is possible for such items to
slip down between the tub and the inner
drum.
leakage from hoses and their connections
after the installation.
● If the appliance is installed in a location
subject to frost, please read the «dangers of
freezing» chapter.
● Any plumbing work required to install this
appliance should be carried out by a
qualified plumber or competent person.
● Any electrical work required to install this
appliance should be carried out by a
qualified electrician or competent person.
● Do not use your washer-dryer to wash
articles with whalebones, material without
hems or torn material.
Download from Www.Somanuals.com. All Manuals Search And Download.
3
● Never pull the power supply cable to remove
the plug from the socket; always take hold of
the plug itself.
● Never use the washer-dryer if the power
supply cable, the control panel, the working
surface or the base are damaged so that the
inside of the washer-dryer is accessible.
Use
● This appliance is designed for domestic use.
It must not be used for purposes other than
those for which it was designed.
● Only wash and dry fabrics which are
designed to be machine washed and dried.
Follow the instructions on each garment
label.
● Do not overload the appliance. See the
relevant section in the user manual.
● Before washing, ensure that all pockets are
empty and buttons and zips are fastened.
Avoid washing frayed or torn articles and
treat stains such as paint, ink, rust, and
grass before washing. Underwired bras must
NOT be machine washed.
● Garments which have been in contact with
volatile petroleum products should not be
machine washed. If volatile cleaning fluids
are used, care should be taken to ensure
that the fluid is removed from the garment
before placing in the machine.
● As some duvets and eiderdowns should be
washed/dried in large commercial machines
because of their bulk, please check with the
manufacturer of the item before washing in a
domestic machine.
● The users should always check that they
have not left their gas lighters (disposable or
otherwise) in their clothing.
Child safety
● This appliance is not intended for use by
person (including children) with reduced
physical sensory or mental capabilities or
lack of experience and knowledge unless
they have been given supervision or
instruction concerning use of the appliance
by a person responsible for their safety.
● Young children should be supervised to
ensure that they do not play with the
appliance.
● The packaging components (e.g. plastic film,
polystyrene) can be dangerous to children -
danger of suffocation! Keep them out of
children’s reach
● Keep all detergents in a safe place out of
children’s reach.
● Make sure that children or pets do not climb
into the drum. To avoid this the machine
incorporates special feature.
● Never dry items that have had contact with
chemicals such as dry cleaning fluid.These
are of a volatile nature and could cause an
explosion.
● Only tumble dry items which have been
washed in water or require airing.
● Plastic detergent dispensers should not
remain in the drum during the drying cycle,
as the plastic used is not designed to
withstand the heat. If you wish to wash-
through-to-dry you should use the
To activate this device, To disable this device
rotate the button
and restore the
(without pressing it)
inside the door
possibility of closing the
door, rotate the button
anti-clockwise until the
groove is vertical.
clockwise until the
groove is horizontal. If
necessary use a coin.
conventional detergent dispenser drawer.
Download from Www.Somanuals.com. All Manuals Search And Download.
4
Description of the appliance
1
Detergent dispenser drawer
1
2
2
Control panel
3
Door opening handle
4
Rating plate
5
Drain pump
6
Adjustable feet
3
4
5
6
Detergent dispenser drawer
Prewash
Wash
Fabric Softener
Download from Www.Somanuals.com. All Manuals Search And Download.
5
Control panel and functions
7
1
2 3 4 5
9
6
8
10
Infos
Henceforth, the programme selector dial, the different buttons and the programme progress
display will be indicated in all the book with the relevant numbers given in the table above.
Programme selector dial and Control Panel symbols:
= White/Coloured cottons,
= Delicates, = Handwash,
Drying, = Rinsing, = Draining ,
safety lock, = Store Dry, = Iron Dry.
= Prewash,
= Synthetics,
= Jeans,
= Easy Iron,
= Cold Wash,
= Sport Intensive,
=
= Spinning,
= Rinse Hold option,
Child
=
●
The programme selector dial allows to select a
Programme selector dial and
On/Off switch
programme and/or to switch the machine on/off. It can
be turned either clockwise or anticlockwise. The light of
the button 8 starts to flash.
1
●
Press this button repeatedly to change the spin speed, if
you want your laundry to be spun at a speed different
from the one proposed by the washer-dryer or to select
the «Rinse Hold» option. The relevant light will light up.
2 Spin reduction button
Download from Www.Somanuals.com. All Manuals Search And Download.
6
●
By means of this button you can choose the required
degree of drying for cottons and synthetics between:
Cupboard dry (cottons and synthetics) and Iron dry
(cottons).The corresponding pilot light illuminates.
3 Automatic Drying button
4 Drying Time button
●
By depressing this button you can select a timed
programme for cotton or synthetics, the relevant phase
light illuminates.
●
With this option it is possible to reduce the washing time
for lightly soiled laundry.
5 Super Quick button
6 Extra Rinse button
●
●
By means of this button, the machine performs some
additional rinses.
The display shows the following information: duration of
the selected programme, selected drying time, incorrect
option selection, alarm codes, child safety lock and end
of programme.
7
Display
●
●
This button allows to start the selected programme; the
corresponding green pilot light stops flashing.
8 Start/Pause button
9 Door locked light
This button interrupts also a programme which is running,
the corresponding green pilot light starts to flash.
●
●
This light indicates when it is possible to open the door.
With this function,the wash programme can be delayed
up to 20 hours to a more convenient for you time.
10
Delay Start button
Download from Www.Somanuals.com. All Manuals Search And Download.
7
Functions
The washing time will be reduced according to
the type of fabric and the selected temperature.
Rinse hold (Button 2)
By selecting this option, the machine will not
drain the water of the last rinse to prevent the
fabrics from creasing.
«Extra rinse» (Button 6)
The machine performs some additional rinses
during the washing cycle. This option is
recommended for people who are allergic to
detergents, and in areas where the water is
very soft.
When the programme has finished, the light of
the button 8 goes off and the light 9
illuminates. The door is locked to indicate that
the water must be emptied out.
To empty out the water see chapter «At the
end of the programme».
«Start/Pause» (Button 8)
This button allows to start the selected
programme; the corresponding green pilot light
stops flashing. This button interrupts also a
programme which is running, the
«Automatic drying» (Button 3)
By means of this button you can choose the
required degree of drying for cottons and
synthetics between: Cupboard dry (cottons and
synthetics) and Iron dry (cottons). The
corresponding pilot light illuminates.
corresponding green pilot light starts to flash.
«Door locked» light (9)
This light illuminates after pressing button 8.
The light 9 indicates when the door can be
opened:
The drying time is automatically adjusted by the
machine: the laundry will be dried to the selec-
ted degree of dryness.
● light on: the door is locked and cannot be
opened. The washing or the drying cycle
starts working and the door is locked.
● light off: the door can be opened. The
washing programme has finished.
If there is water left in the tub, the light 9
remains lit. The door will be still locked and it
will be necessary to empty out before
opening the door.
Drying Time button (Button 4)
By depressing this button you can select a
timed programme for cotton or synthetics. The
relevant light illuminates.
For Cottons and Synthetics you can select a
drying time from 10 minutes to 250 minutes
(4.10). Every time you press the button the
time increases by 5 mins.
Note!
To empty out the water see chapter «At the
end of the programme».
The programme time will automatically increase
by up to 2 minutes. This is quite normal.
«Delay start» (Button 10)
«Super Quick» (Button 5)
The wash programme can be delayed from 30
min - 60 min - 90 min, 2 hours and then by 1
hour up to a maximum of 20 hours.
The Delay start cannot be selected with
«Drain» programme.
Short cycle for lightly soiled items or for laundry
that have been used or worn for a short time
and needs only freshening up.
We recommend you to reduce the fabrics
loading.
Download from Www.Somanuals.com. All Manuals Search And Download.
8
Programme table
Programme/
Temperature
Description of
programme
Type of laundry
Options
Main wash, Rinses,
Long spin at the maximum
speed
Max load: 7 kg
Reduced load: 3.5 kg
Spin reduction /
Rinse Hold
Super Quick, Extra rinse
Cottons
90° - 60°
White cotton (heavy
soiled cotton items)
Main wash, Rinses, Long
spin at the maximum
speed, Max load: 7 kg,
Reduced load: 3.5 kg
White and fast colour
cotton (normally soiled
cotton items)
Spin reduction / Hold
Extra rinse
Cottons
60° Eco
Main wash, Rinses, Long
spin at the maximum,
Max load: 7 kg, Red.
load: 3.5 kg
Spin reduction /
Rinse Hold
Super Quick, Extra rinse
White and colour
cotton (lightly soiled
cotton items)
Cottons
40°- 30°
Prewash, Main wash,
Rinses, Long spin at the
maximum speed, Max load:
7 kg, Red. load: 3.5 Kg
Spin reduction /
Rinse Hold
Super Quick, Extra rinse
White cotton
(white cotton items
heavily soiled )
Cotton
90° + Prewash
White cotton and fast
colour cotton
(cotton items normally
soiled )
Prewash, Main wash
Spin reduction /
Rinse Hold
Super Quick, Extra rinse
Cotton
60° + Prewash
Rinses, Long spin at the
maximum speed, Max load:
7 kg, Red. load: 3.5
Prewash, Main wash
Rinses, Long spin at the
maximum speed, Max
load: 7 kg, Red.load: 3.5
Kg
Spin reduction /
Rinse Hold
Super Quick, Extra rinse
Cotton colour
(cotton colour items
normally soiled )
Cotton
40° + Prewash
Main wash, Rinses
Short spin
Max load: 3.5 kg
Reduced load: 2 kg
Spin reduction /
Rinse Hold
Super Quick, Extra rinse
Synthetics
60° - 40° - 30°
Synthetic or mixed
fabrics,
Main wash
Rinses
Short spin
Spin reduction /
Rinse Hold
Extra rinse
Synthetic or mixed
fabrics to be gentle
washed and spun.
Synthetics
Easy iron 40°
Max load: 1 kg
Download from Www.Somanuals.com. All Manuals Search And Download.
9
Programme table
Programme/
Temperature
Description of
programme
Type of laundry
Options
Main wash, Rinses
Short spin
Max load: 3.5 kg
Reduced load: 2 kg
Spin reduction / Rinse
Hold
Super Quick, Extra rinse
Delicates
40° - 30°
Delicate fabrics, for
example curtains.
Main wash, Rinses
Short spin
Max load: 2 kg
Spin reduction / Rinse
Hold
Handwash
40° - 30° - Cold
Special programme for
hand washing fabrics
Special programme for
jeans or dark colours
cotton items
Jeans
40°
Spin reduction / Rinse
Hold
Main Wash, Rinses, Long
spin, Max load: 3.5 kg
Prewash, Main wash,
Rinses, Short spin, Max
load: 3 kg
Sport Intensive
40°
Spin reduction / Rinse
Hold, Extra rinse
Special programme for
sport items heavily soiled
Separate rinse cycle for
hand washed cotton
items.
3 rinses, Long spin at the
maximum speed, Max
load: 7 kg
Spin reduction / Rinse
Hold, Extra rinse
Rinses
Drain
For emptying out the last
rinse water in
programmes with the
Rinse Hold option.
Draining of water
Separate spin for
cottons.
Drain and long spin at the
maximum speed
Spin red.
Spin
To interrupt a running programme, to cancel an incorrect option selection or to
switch the machine off,
O
Download from Www.Somanuals.com. All Manuals Search And Download.
10
Programme information
This programme can be selected for slightly or normally soiled
cotton items. The temperature will decrease and the washing time
will be extended. This allows to obtain a good washing efficiency by
saving energy.
Eco programme
Washing programme for machine washable wool as well as for hand
washable woollens and delicate fabrics with the «hand washing»
(Wool)
Handwash
care symbol
.
With this programme it is possible to wash free time items as pants,
shirts or jackets in Jeans and also jersey made of hi-tech materials.
Some extra rinses will be carried out by the machine.
Jeans
Selecting this programme, the laundry is gently washed and spun to
avoid any creasing. In this way ironing is easier. Furthermore the
machine will perform additional rinses.
Easy Iron
This programme is suitable for washing heavily soiled sport items.
The machine will add automatically a prewash phase before the
main wash to eliminate mud stains. The washing temperature is
40°C. The maximum spin speed is reduced.
Sport intensive
We recommend you NOT to put detergent in the compartment
marked by the symbol
(Prewash).
With this programme it is possible to rinse and spin cotton garments
which have been washed by hand.
The machine performs 3 rinses, followed by a final spin at maximum
speed.
Rinses
Drain
The spin speed can be reduced by pressing button 2.
For emptying out the water of the last rinse in programmes with the
Rinse Hold option.
Turn first the programme selector dial to «O», then select programme
Drain and press 8.
Separate spin for hand washed garments and after programmes
with Rinse Hold option. Before selecting this programme the
selector dial must be turned to «O». You can choose the speed by
means of the relevant button to adapt it to the fabrics to be spun.
Spin
To reset a programme and to switch off the machine turn the
selector dial to «O». Now can a new programme be selected.
O = Cancelling/Off
Download from Www.Somanuals.com. All Manuals Search And Download.
11
Washing and drying hints
Avoid drying dark clothes with light coloured
fluffy items such as towels as these can attract
the fluff.
Sorting the laundry
Follow the wash code symbols on each
garment label and the manufacturer’s washing
instructions. Sort the laundry as follows: whites,
coloureds, synthetics, delicates, woollens.
Remove the laundry when the appliance has
finished drying.
To avoid a static charge when drying is com-
pleted, use either a fabric softener when you
are washing the laundry or a fabric conditioner
specifically for tumble dryers.
Temperatures
for normally soiled white cottons
and linen (e.g. tea cloths, towels,
tablecloths, sheets...)
90° or 95°
50°/60°
Particularly delicate items such as synthetic
curtains, woollen and silk, garments with metal
inserts, nylon stockings, bulky garments such
as anoraks, bedcovers, quilts, sleeping bags
and duvets must not be machine dried.
for normally soiled, colour fast
garments (e.g. shirts, night
dresses, pyjamas....) in linen,
cotton or synthetic fibres and for
lightly soiled white cotton (e.g.
underwear).
Garments padded with foam-rubber or materi-
als similar to foam-rubber must not be machine
dried; they represent a fire hazard.
for delicate items (e.g. net
Also, fabrics containing residues of setting
lotions or hair sprays, nail solvents or similar
solutions must not be machine dried in order to
avoid the formation of harmful vapours.
curtains), mixed laundry including
30°-40°-Cold synthetic fibres and woollens
bearing the label «pure new wool,
machine washable, non-shrink».
For drying, follow the indications given on the
manufacturer’s labels.
Before loading the laundry
Never wash whites and coloureds together.
Whites may lose their «whiteness» in the
wash.
New coloured items may run in the first wash;
they should therefore be washed separately
the first time.
Make sure that no metal objects are left in
the laundry (e.g. hair clips, safety pins,
pins). Button up pillowcases, close zip
fasteners, hooks and poppers. Tie any belts
or long tapes.
Remove persistent stains before washing.
Rub particularly soiled areas with a special
detergent or detergent paste.
Treat curtains with special care. Remove hooks
or tie them up in a bag or net.
For drying, follow the indications given on the
manufacturer’s labels.
May be tumble dried
Drying at high temperature
Drying at reduced temperature
Do not tumble dry
IMPORTANT!
As a dryer, the machine works on the
condensation principle.
Therefore, the water tap must be open and
the drain hose must drain water into a sink
or into the drain pipe, even during the dry-
ing cycle.
Download from Www.Somanuals.com. All Manuals Search And Download.
12
Oil based paint: moisten with benzine stain
remover, lay the garment on a soft cloth and
dab the stain; treat several times.
Maximum loads
Recommended loads are indicated in the
programme charts.
Dried grease stains: moisten with turpentine,
lay the garment on a soft surface and dab the
stain with the fingertips and a cotton cloth.
Rust: oxalic acid dissolved in hot water or a
rust removing product used cold. Be careful
with rust stains which are not recent since the
cellulose structure will already have been
damaged and the fabric tends to hole.
Mould stains: treat with bleach, rinse well
(whites and fast coloureds only).
General rules:
Cotton, linen: drum full but not too tightly
packed;
Synthetics: drum no more than half full;
Delicate fabrics and woollens: drum no more
than one third full.
Washing a maximum load makes the most
efficient use of water and energy.
For heavily soiled laundry, reduce the load
size.
Grass: soap lightly and treat with bleach
(whites and fast coloureds only).
Ball point pen and glue: moisten with
acetone (*), lay the garment on a soft cloth and
dab the stain.
Laundry weights
The following weights are indicative:
Lipstick: moisten with acetone as above, then
treat stains with methylated spirits. Remove
any residual marks from white fabrics with
bleach.
Red wine: soak in water and detergent, rinse
and treat with acetic or citric acid, then rinse.
Treat any residual marks with bleach.
Ink: depending on the type of ink, moisten the
fabric first with acetone (*), then with acetic
acid; treat any residual marks on white fabrics
with bleach and then rinse thoroughly.
Tar stains: first treat with stain remover,
methylated spirits or benzine, then rub with
detergent paste.
bathrobe
napkin
quilt cover
sheet
pillow case
tablecloth
1200 g
100 g
700 g
500 g
200 g
250 g
200 g
100 g
200 g
100 g
600 g
200 g
500 g
100 g
100 g
towelling towel
tea cloth
night dress
ladies’ briefs
man’s work shirt
man’s shirt
man’s pyjamas
blouse
(*) do not use acetone on artificial silk.
men’s underpants
Detergents and additives
Good washing results also depend on the
choice of detergent and use of the correct
quantities to avoid waste and protect the
environment. Although biodegradable,
detergents contain substances which, in large
quantities, can upset the delicate balance of
nature.
Removing stains
Stubborn stains may not be removed by just
water and detergent. It is therefore advisable to
treat them prior to washing.
Blood: treat fresh stains with cold water. For
dried stains, soak overnight in water with a
special detergent then rub in the soap and
water.
The choice of detergent will depend on the
type of fabric (delicates, woollens, cottons,
Download from Www.Somanuals.com. All Manuals Search And Download.
13
etc.), the colour, washing temperature and
degree of soiling.
Follow the product manufacturers’ instructions
on quantities to use.
All commonly available washer-dryer
detergents may be used in this appliance:
Degrees of water hardness
● powder detergents for all types of fabric,
● powder detergents for delicate fabrics (60°C
max) and woollens,
Follow the product manufacturers’ instructions
on quantities to use.
Use less detergent if:
● liquid detergents, preferably for low
temperature wash programmes (60°C max)
for all types of fabric, or special for woollens
only.
● you are washing a small load,
● the laundry is lightly soiled,
● large amounts of foam form during washing.
The detergent and any additives must be
placed in the appropriate compartments of the
dispenser drawer before starting the wash
programme.
If using concentrated powder or liquid
detergents, a programme without prewash
must be selected.
The washer-dryer incorporates a recirculation
system which allows an optimal use of the
concentrated detergent.
Degrees
Level Characteristic
German
°dH
French
°T.H.
1
2
3
4
soft
medium
hard
0-7
8-14
15-21
> 21
0-15
16-25
26-37
> 37
very hard
Pour liquid detergent into the dispenser drawer
compartment marked
the programme.
just before starting
Any fabric softener or starching additives must
be poured into the compartment marked
before starting the wash programme.
Follow the product manufacturer’s
recommendations on quantities to use and do
not exceed the «MAX» mark in the
detergent dispenser drawer.
Quantity of detergent to be used
The type and quantity of detergent will depend
on the type of fabric, load size, degree of
soiling and hardness of the water used.
Water hardness is classified in so-called
«degrees» of hardness. Information on
hardness of the water in your area can be
obtained from the relevant water supply
company, or from your local authority.
Download from Www.Somanuals.com. All Manuals Search And Download.
14
Before the first use
This function remains able also when the
washer-dryer is not working.
There are two different ways to set this option:
WARNING!
Ensure that the electrical and water
connections comply with the installation
instructions.
●
before pressing the button 8: it will be
impossible to start the machine.
after pressing the button 8 it will be
impossible to change any other programme
or option.
IMPORTANT!
Remove the polystyrene block and any
material from the drum.
●
To enable (disable) this option press
IMPORTANT!
Pour 2 litres of water into the main wash
compartment
simoultaneously for about 6 seconds 2 and 3
buttons until the icon
on (from) the display.
appears (disappears)
of the detergent drawer in
order to activate the ECO valve. Then run a
cotton cycle at 90°C, without any laundry in the
machine, to remove any manufacturing residue
from the drum and tub. Pour 1/2 a measure of
detergent into the dispenser drawer and start
the machine.
Acoustic signals
The machine is provided of an acoustic device,
which sounds in the following cases:
●
at the end of the cycle
●
in the event of operating problems
Child safety lock
By pressing the 4 and 5 buttons
simultaneously for about 6 seconds, the
acoustic signal is deactivated (except for the
events of operating problems).
This device permits you to leave the appliance
unsupervised without having the worry that
children might be injured by or cause damage
to the appliance.
By pressing these buttons again, the the
acoustic signal is reactivated.
Operating sequence
Washing
2. Measure out the detergent and the fabric
softener
1. Load the laundry
Open the door by
carefully pulling the
door handle outwards.
Place the laundry in
the drum, one item at
a time, shaking them
out as much as
Pull out the dispenser drawer until it stops.
Measure out the amount of detergent required,
possible. Close the door.
Download from Www.Somanuals.com. All Manuals Search And Download.
15
automatically adjust the duration of the drying
cycle to the selected degree.
Also this button allows you to select a drying
time for Cottons and Synthetics from 10
minutes to 250 minutes (4.10). Every time you
press this button the time increases by 5 mins.
pour it into the main wash compartment
and, if you wish to carry out a programme with
the prewash phase, pour it into the
compartment marked
.
If required, pour fabric softener into the
compartment marked
(the amount used
must not exceed the «MAX» mark in the
drawer). Close the drawer gently.
Select the desired option by means of
buttons 5 and 6
Depending on the programme, different
functions can be combined. These must be
selected after choosing the desired programme
and before depressing the button 8. The
corrisponding light illuminates.
Select the required programme by means
ofthe programme selector dial (1)
Turn the programme selector dial to the
required programme. The green light of button
8 starts to flash.
It can be turned either clockwise or
anticlockwise. On position «O» the programme
is reset and the machine is switched OFF.
At the end of the programme the selector
dial must be turned to position «O», to
switch the machine off.
For more information about the compatibility of
the options with the washing programmes,
refer to the section «Programmes table».
Select the delayed start by pressing the
button 10
IMPORTANT!
Depress button this button to select the
required delay.
If you turn the programme selector dial to
another programme when the machine is
working, the red light will of the button 8
flashes 3 times and the message Err is
displayed on the display to indicate a wrong
selection. The machine will not perform the
new selected programme.
The selected delay time value will appear on
the display for few seconds, then the duration
of the programme will appear again.
You must select this option after you have set
the programme and before you press the
button 8.
You can cancel the delay time at any moment,
before you press button 8.
If you have already pressed it, and you wish
to cancel the delay time, proceed as follows:
• set the washing machine to PAUSE by
pressing button 8;
Select the spin speed or the Rinse Hold
option by pressing button 2
The relevant light will light up.
When selecting a programme, the light
corresponding to the maximum speed allowed
for that programme will illuminate.
• press the button 10 once. On the display will
Select the degree of dryness or the duration
of the drying cycle by means of buttons 3
and 4
appear the symbol «0’».
• press button 8 again to start the programme.
IMPORTANT!
The relevant light illuminates.
• If the programme has already started, the
selected delay can be modified only after you
have turned the programme selector dial to
By depressing the button 3 it is possible to
select the degrees of dryness for cotton or
synthetics items. The washer dryer will
Download from Www.Somanuals.com. All Manuals Search And Download.
16
the «O» position and after you have selected
the programme again.
• The door will be locked throughout the delay
time. If you need to open the door, you must
first set the washer dryer to PAUSE by
pressing button 8. After you have closed the
door, press the same button again.
The delay time value
decreases by one
unit every hour, 90
minutes and then,
when 1 hour remain,
every minute.
The incorrect option selection is indicated
by the message Err displayed for a few
seconds and by flashing of the red light button
8.
Note!
The Delay Start cannot be selected with
«Drain» programme.
Display
The display shows the following information:
After selecting a programme the duration of
the selected programme appears in minutes
or hours and minutes on the display .(e.g.
2 .05 )
In the event of operating problems, some
alarm codes can be displayed, (see para-
graph “Something not working”).
During the program-
me, the time remai-
ning is updated every
minute.
2.00
E20
Selected drying time
The End of programme or the stop wit
water left in the tub is indicated by a flashing
zero «0».
After selecting a drying programme programme
the drying time is shown in minutes or hours
and minutes.
After the programme
has started, the time
remaining is updated
every minute.
1.00
0
Start the programme by pressing button 8
To start the selected programme, press this
button; the corresponding green pilot light
stops flashing.
The Delayed start appears on the display for
about 3 seconds, then the duration of the
previously selected programme is displayed.
The pilot light 9 illuminates to indicate that the
appliance starts operating and the door is
locked.
Download from Www.Somanuals.com. All Manuals Search And Download.
17
IMPORTANT!
(Pay attention to the water level and
temperature!).
After this procedure, it will be necessary to set
the programme and the options again and then
to press button 8.
If an option which is not compatible with the set
wash programme is selected, the message Err
is displayed for few seconds and the red light
of this button flashes for 3 times.
At the end of the programme
Altering an option or a running programme
It is possible to change any option before the
programme carries it out.
Before you make any change, you must pause
the washing machine by pressing button 8.
The washer dryer stops automatically. Some
acustic signals sound and on the display will
appear a flashing «0 ». The button 8 light and
the light 9 go off. The door can be opened.
If, at the end of a programme, there is water in
the tub (light 9 still on), to empty out the water
follow the following instructions:
Changing a running programme is possible
only by resetting it. Turn the programme
selector dial to «O» and then to the new
programme position. Start the new programme
by pressing button 8 again.
To empty out the water:
1. turn the programme selector dial to «O»
2. select the Drain»or «Spin» programme
3. reduce the spin speed, if needed, by means
of the button 2
4. press button 8
5. at the end of the programme, the display
shows a flashing zero «0», the light 9 goes
off and it will be possible to open the door.
Turn the programme selector dial to «O» to
switch the machine off.
Remove the laundry from the drum and
carefully check that the drum is empty.
If you do not intend to carry out another wash,
close the water tap.
Leave the door open to prevent the formation
of mildew and unpleasant smells.
Stand By: If your laundry is not removed within
10 minutes after the programme is finished, the
back light of the display switches off and the
energy saving system will be enabled. Only the
pilot light of the button 8 is blinking to indicate
that the appliance has to be switched off. By
pressing any button the appliance will come
out from the energy saving status and you can
set another programme or switch the appliance
off.
The washing water in the tub will not empty
out.
Interrupting a programme
Press button 8 to interrupt a programme which
is running, the corresponding light starts to
flash. Press the button again to restart the
programme.
Cancelling a programme
Turn the selector dial to «O» to cancel a
programme which is running. Now you can
select a new programme.
Opening the door after the programme has
started
First set the machine to pause by pressing the
button 8.
If the light 9 goes off, the door can be opened.
If it does not go off, this means that the
machine is already heating, that the water level
is above the bottom edge of the door. In this
cases the door cannot be opened.
If you cannot open the door but you need to
open it you have to switch the machine off by
turning the selector dial to «O». The door can
be opened after a few minutes.
Download from Www.Somanuals.com. All Manuals Search And Download.
18
Drying
Note!
Drying only
The different type of cottons (towelling, sheets,
shirts, and so on) or any laundry items rolling
up during the spinning phase may result in
partial dryness. In the exceptional case that at
the end of the cycle the laundry remains
slightly wet, we suggest that you unfold the
rolled up items, redistribute them evenly in the
drum and select an additional drying cycle of
20-30 minutes.
The max load to dry in your washer -dryer is 3.5
kg for cotton and 2 kg for synthetics.
Note!
Only with the timed drying, it is possible also to
dry up to 5 kg of cotton items (see the drying
time table).
The water tap must be open and the drain
hose must be positioned in the sink or connect-
ed to the drain pipe.
6. At the end of the programme, the buzzer
sounds. A flashing zero «0» will appear on
the display.
1. Load the laundry.
At this point, begins the anti-crease phase
which lasts for about 10 minutes. During
this time the light 9 is alight, the door can-
not be opened and the display keeps
showing three flashing zeros «0».
At the end of this phase, the pilot light 9
goes off and the door can be opened.
2. Turn the selector dial to «Cotton» or
«Synthetics» programme in the «Drying»
sector.
3. For the automatic drying, «Store dry»
(only for synthetics) or «Iron dry», press
the button 3 until the light corresponding to
the desired dryness degree illuminates.
Note!
4. For the timed drying, press the button 4
until the time you want appears on the dis-
play (see the drying programmes).
Every time you press this button the drying
time increases by 5 mins.
If you whish to open the door before or
during the anti-crease phase or to interrupt it,
press any button or turn the programme selec-
tor dial to any programme position (except
«O»), the door can be immediately opened.
7. Turn the selector dial to the «O» position to
switch the machine off. Remove the laun-
dry.
Note!
The programme time will automatically increase
by up to 2 minutes. This is quite normal.
5. Press button 8 to start the programme.
After the programme has started, the time
remaining is updated every minute.
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Autodrying (NON-STOP
programme)
Warning!
For NON-STOP programmes, it is essential not
to exceed the maximum load sizes of 3.5 kg for
cotton and 2 kg for synthetics.
Note!
Only with the timed drying, it is possible also to
dry up to 5 kg of cotton items (see the drying
time table).
Do not use a dosing device/ball when carry-
ing out a washing & drying programme.
1. Load the laundry.
2. Add detergent and fabric softener.
3. Switch the machine on by turning the
selector dial to the selected wash pro-
gramme/fabric.
4. Select the dryness degree or the drying
time by pressing button 3 and 4. The dis-
play shows the entire duration of the wash-
ing and the selected drying cycle.
5. Select the required options by means of
the relevant buttons. If possible, do not
select a spin speed lower than that pro-
posed by the appliance to avoid a too long
drying time so saving energy.
In any case the reduction of the spin speed
is only possible after selecting drying.
The lowest value with AUTOMATIC DRYING is
900 r.p.m. for cottons and synthetics
The lowest value with TIMED DRYING you
can select is 700 r.p.m. for synthetics
6. Start the programme by pressing button 8.
7. At the end of the programme, turn the
selector dial to the «O» position to switch
the machine off. Remove the laundry.
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Automatic Drying Programmes
Degree of drying
Type of fabric
Drying time mins
Cotton and linen
(bathrobes, bath towels, etc)
3.5 kg
Store dry
Suitable for items to put away
without ironing
Synthetics and mixed fabrics (jumpers,
blouses, underwear, household linen)
2 kg
3 kg
Cotton and linen (sheets, tablecloths,
shirts, etc.)
Iron dry
Suitable for ironing
Drying Time
Drying time
Degree of drying
Type of fabric
Max Load
Spin speed
mins
5 kg
1000 rpm
1000 rpm
1000 rpm
195-215
Cotton and linen (bathrobes,
bath towels, etc
3,5 kg
1,5 kg
100-110
50-60
Suitable for items to
put away without
ironing
Synthetics and mixed fabrics
(jumpers, blouses, under-
wear, household linen)
2 kg
1 kg
900 rpm
900 rpm
70-80
35-45
5 kg
1000 rpm
1000 rpm
1000 rpm
115-130
80-90
Suitable
for ironing
Cotton and linen (sheets,
tablecloths, shirts, etc.)
3,5 kg
1,5 kg
45-55
In compliance with EC directive EN 50229 the cotton reference programme for the data entered
in the Energy Label must be tested dividing the maximum washing load by two equal parts and
drying with TIMED DRYING each of them.
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Care and cleaning
IMPORTANT!
To aid cleaning, the top part of the additive
compartment should be removed.
Remove the drawer by pressing the catch
downwards and by pulling it out. Flush it out
under a tap, to remove any traces of
accumulated powder.
You must DISCONNECT the appliance from
the electricity supply, before you can carry out
any cleaning or maintenance work.
Descaling
The water we use normally contains lime. It is
a good idea to periodically use a water
softening powder in the machine. Do this
separately from any laundry washing, and
according to the softening powder
manufacturer's instructions. This will help to
prevent the formation of lime deposits.
Cleaning the drawer recess
Having removed the
drawer, use a small
brush to clean the
recess, ensuring that
all washing powder
residue is removed
from the upper and
lower
Maintenance Wash
With the use of low temperature washes it is
possible to get a build up of residues inside the
drum.
We recommend that a maintenance wash be
performed on a regular basis.
part of the recess.
Replace the drawer and run the rinse
programme without any clothes in the drum.
Cleaning the pump
To run a maintenance wash:
●
●
●
The drum should be empty of laundry.
Select the hottest cotton wash programme.
Use a normal measure of detergent, must be
a powder with biological properties.
The pump should be inspected if
• the machine does not empty and/or spin
• the machine makes an unusual noise during
draining due to objects such as safety pins,
coins etc. blocking the pump.
External cleaning
Clean the exterior cabinet of the appliance with
soap and water only, and then dry thoroughly.
Proceed as follows:
• disconnect the appliance.
• if the appliance is operating, wait, if
necessary, until the water has cooled down.
• open the pump door levering on the groove
with a coin (or with the suitable tool, that you
can find in the bag containing the instruction
booklet depending on the model).
Cleaning the dispenser drawer
The washing powder and additive dispenser
drawer should be cleaned regularly.
• place a bowl with a small edge close to the
pump to collect any spillage
Download from Www.Somanuals.com. All Manuals Search And Download.
22
• Close the pump
door.
1
2
• pull out the emergency emptying cap from the
filter cover, using a pliers.
IMPORTANT!
When the appliance is in use and depending
on the programme selected there can be hot
water in the pump.
Never remove the pump cover during a wash
cycle, always wait until the appliance has
finished the cycle, and is empty. When
replacing the cover, ensure it is securely
retightened so as to stop leaks and young
children being able to remove it.
• when no more water comes out, unscrew the
pump cover, using a pliers, and remove the
filter. Always keep a rag nearby to dry up
spillage of water when removing the cover.
2
1
Cleaning the water inlet filter
If your water is very hard or contains traces of
lime deposit, the water inlet filter may become
clogged.
It is therefore a good idea to clean it from time
to time.
• Remove any objects from the pump impeller
by rotating it.
Turn off the water tap.
Unscrew the water
inlet hose. Clean the
filter using a hard
bristle brush. Tighten
up the inlet hose.
• replace the emergency emptying cap into the
filter cover and fix it firmly.
The dangers of freezing
If the machine is exposed to temperatures
below 0°C, certain precautions should be
taken:
• pull out the plug from the power socket;
Download from Www.Somanuals.com. All Manuals Search And Download.
23
• turn off the water tap.
• unscrew the inlet hose.
Emergency emptying out
If the water is not discharged, proceed as
follows to empty out the machine:
• place a bowl with a small edge close to the
pump to collect any spillage from the
emergency emptying hose.
Place the end of the inlet hose in a bowl
placed on the floor and let water drain out.
• pull out the plug from the power socket;
• close the water tap;
• if necessary, wait until the water has cooled
down;
• screw the water inlet hose back on and
reposition the emergency emptying cap on
again into the filter cover.
• open the pump door using the suitable tool;
• place a bowl with a small edge close to the
pump to collect any spillage. Remove the
emergency emptying cap from the filter
cover. The water should drain by gravity into
the bowl. When the bowl is full, put the cap
back on filter cover. Empty the bowl. Repeat
the procedure until water stops flowing out;
• when you intend to start the machine up
again, make sure that the room temperature
is above 0°C.
IMPORTANT!
Every time you drain the water through the
emergency emptying hose you must pour 2
litres of water into the main wash compartment
of the detergent drawer and then run the drain
programme. This will activate the ECO VALVE
device avoiding that part of the detergent
remains unused at next washing.
• clean the pump if necessary as previously
described;
• replace the filter into the pump and screw it
firmly as previously described;
• replace the emergency emptying cap into the
filter cover and close the pump door.
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Something not working
IMPORTANT!
Certain problems are due to lack of simple maintenance or oversights, which can be solved easily
without calling out an engineer. Before contacting your local Service Centre, please carry out the
checks listed below.
During machine operation it is possible that the red pilot light of the button 8 flashes, the buzzer
sounds and one of the following alarm codes appears on the display to indicate that the machine
is not working.
●
●
●
E 10: problem with the water supply
E 2 0: problem with water draining
E 40: door open.
Once the problem has been eliminated, press the button 8 to restart the programme. If after all
checks, the problem persists, contact your local Service Centre.
Malfunction
Possible Cause / Solution
The door has not been closed. E 40
• Close firmly the door.
The plug is not properly inserted in the power socket.
• Insert the plug into the power socket.
There is no power at the socket.
• Please check your domestic electrical installation.
The main fuse has blown.
• Replace the fuse.
The washer-dryer does not start:
The selector dial is not correctly positioned and the
button 8 has not been pressed.
• Please turn the selector dial and press the button 8
again.
The Child Safety Lock or the Delay start function
option has been selected.
• Disable the «Child Safety Lock» or the «Delay
start» function.
The water tap is closed. E 10
• Open the water tap.
The inlet hose is squashed or kinked. E 10
• Check the inlet hose connection.
The machine does not fill:
The filter in the inlet hose is blocked. E 10
• Clean the water inlet hose filter.
The door is not properly closed. E 40
• Close firmly the door.
Download from Www.Somanuals.com. All Manuals Search And Download.
25
Malfunction
Possible Cause / Solution
The end of the drain hose is too low.
• Refer to relevant paragraph in «water drainage»
section.
The machine fills then empties
immediately:
The drain hose is squashed or kinked. E 2 0
• Check the drain hose connection.
The drain pump is clogged. E 2 0
• Clean the drain pump.
The machine does not empty and/or
does not spin:
TheRinse Hold option has been selected.
• Select the Drain or Spin programmes
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Too much detergent or unsuitable detergent (creates
too much foam) has been used.
• Reduce the detergent quantity or use another one.
Check whether there are any leaks from one of the
inlet hose fittings. It is not always easy to see this as
the water runs down the hose; check to see if it is
damp.
There is water on the floor:
• Check the water inlet hose connection.
The inlet hose is damaged.
• Change it with a new one.
The cap on the emergency emptying hose has not
been replaced after cleaning the pump.
•
Put the cap back on the emergency emptying and
place the latter back in its seat.
Too little detergent or unsuitable detergent has been
used.
• Increase the detergent quantity or use another one.
Stubborn stains have not been treated prior to
washing.
• Use commercial products to treat the stubborn
stains.
Unsatisfactory washing results:
The correct temperature was not selected.
• Check if you have selected the correct
temperature.
Excessive laundry load.
• Introduce into the drum less laundry.
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Malfunction
Possible Cause / Solution
The programme is still running.
• Wait the end of washing cycle.
The door lock has not been released.
• Wait untill the light 9 has gone off.
The door will not open:
There is water in the drum.
• Select drain or spin programme to empty out the
water.
The transit bolts and packing have not been
removed.
• Check the correct installation of the appliance.
The support feet have not been adjusted.
• Check the correct levelling of the appliance.
The machine vibrates or is noisy:
The laundry is not evenly distributed in the drum.
• Redistribute the laundry.
Maybe there is very little laundry in the drum.
• Load more laundry.
The electronic unbalance detection device has cut in
because the laundry is not evenly distributed in the
drum. The laundry is redistributed by reverse rotation
of the drum. This may happen several times before
the unbalance disappears and normal spinning can
resume. If, after 10 minutes, the laundry is still not
evenly distributed in the drum, the machine will not
spin. In this case, redistribute the load manually and
select the spin programme.
Spinning starts late or the machine
does not spin:
●
Redistribute the laundry.
The machine is fitted with a type of motor which
makes an unusual noise compared with other
traditional motors. This new motor ensures a softer
start and more even distribution of the laundry in the
drum when spinning, as well as increased stability of
the machine.
The machine makes an unusual noise
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Malfunction
Possible Cause / Solution
The drying time has not been selected.
• Select the drying time.
The water tap is not turned on (E 10)
• Open the water tap.
The drain filter is clogged (E 2 0)
• Clean the drain filter.
The machine does not dry or does not
dry properly
The machine is overloaded.
• Introduce into the drum less laundry.
The selected drying programme or time/degree was
not suitable for the laundry.
• Select the suitable drying programme or time/degree
for the laundry.
Machines based on modern technology operate very
economically using very little water without affecting
performance.
No water is visible in the drum
If you are unable to identify or solve the
problem, contact our service centre.
Before telephoning, make a note of the model,
serial number and purchase date of your
machine: the Service Centre will require this
information.
Mod. ... ... ...
Prod. No. ... ... ...
Ser. No. ... ... ...
Download from Www.Somanuals.com. All Manuals Search And Download.
28
Technical data
Dimensions
Width
60 cm
85 cm
63 cm
Height
Depth (inclunding the porthole)
Electrical connection Voltage -
Overall power - Fuse
Information on the electrical connection is given on the rating
plate on the inner edge of the appliance door
Water supply pressure
Minimum
Maximum
0,05 MPa
0,8 MPa
Maximum Washing Load
Maximum Drying Load
Cotton
7
kg
Cotton Big Capacity
Cotton
Synthetics
5. 0 kg
3.5 kg
2
kg
1000 rpm
Spin Speed
Maximum
Download from Www.Somanuals.com. All Manuals Search And Download.
29
Consumption values
Programme
Programme
duration
(in minutes)
Energy
consumption
(in kWh)
Water
consumption
(in litres)
Cottons 90°C
2.1
65
59
60
Cottons 60° Eco(*)
Cottons 40°C
1.19
0.77
Cottons 60° + Prewash
Synthetics 60°C
1.6
1.05
0.6
0.4
75
57
63
55
Delicates 40°C
Handwash 40°C
Information
The consumption data shown on this chart is
to be considered purely indicative, as it may
vary depending on the quantity and type of
laundry, on the inlet water temperature and on
the ambient temperature. It refers to the
highest temperature for each wash
programme.
(*)The “Cottons 60° Eco” is the reference
programme with a load of 7 kg for the data
entered in the energy label, in compliance
with EEC 92/75 standards.
Download from Www.Somanuals.com. All Manuals Search And Download.
30
Installation instruction
Unpacking
All transit bolts and packing must be removed
before using the appliance.
5. Remove the bracket D, refit the six smaller
bolts C and slide out the relevant plastic
spacer E.
You are advised to keep all transit devices so
that they can be refitted if the machine ever
has to be transported again.
6. Open the porthole, take out the inlet hose
from the drum and remove the polystyrene
block fitted with the adhesive tape on the
door seal.Open the porthole, take out the
inlet hose from the drum and remove the
polystyrene block fitted with the adhesive
tape on the door seal.
7. Fill the smaller upper hole and the two large
ones with the corresponding plastic plug
caps supplied in the bag containing the
instruction booklet.
1. After removing all the packaging, carefully
lay machine on it’s back to remove the
polystyrene base from the bottom.
2. Remove the power supply cable and the
draining hose from the hose holders on the
rear of the appliance.
Positioning
A
Install the machine on a flat hard floor. Make
sure that air circulation around the machine is
not impeded by carpets, rugs etc.
Check that the machine does not touch the
wall or other kitchen units.
C
B
B
C
3. With a suitable spanner unscrew and
remove the central rear bolt A.
Levelling
4. Unscrew and remove the two large rear
bolts B and the six smaller bolts C.
Level the washer-dryer by raising or lowering
the feet. The feet may be tight to adjust as they
incorporate a self locking nut, but the machine
MUST be level and stable.
E
C
D
If necessary, check the
setting with a spirit
level.
C
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Any necessary adjustment can be made with a
spanner. Accurate levelling prevents vibration,
noise and displacement of the machine during
operation.
Never place cardboard, wood or similar
materials under the machine to compensate for
any unevenness in the floor.
3.Set the hose
correctly by
loosening the ring
nut.
After positioning the
inlet hose, be sure to
tighten the ring nut
again to prevent
leaks.
Some vibration is inevitable, especially if
mounted on a wooden floor.
Sprung woden floors are particularly
susceptible to vibration. For advice, consult a
builder. If possible, always place the machine
on a solid floor.
IMPORTANT!
Before connecting up the machine to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.
Water inlet
Warning
Water drainage
The end of the drain hose can be positioned in
three ways:
This appliance must be connected to a cold
water supply.
Hooked over the
edge of a sink using
the plastic hose
guide supplied with
the machine. In this
case, make sure the
end cannot come
unhooked when the
1. Connect the hose to a tap with a 3/4” thread.
Always use the hose supplied with the
appliance. The inlet hose must not be
lengthened. If it is too short and you do not
wish to move the tap, you will have to
purchase a new, longer hose specially
designed for this type of use.
machine is emptying. This could be done by
tying it to the tap with a piece of string or
attaching it to the wall.
In a sink drain pipe
branch. This branch
must be above the
trap so that the bend
is at least 60 cm
above the ground.
Do not use the hose from your previous
machine to connect to the water supply.
2. The other end of the inlet hose which
connects to the machine can be turned as
showed in the picture. Do not place the inlet
hose downwards. Angle the hose to the left
or right depending on the position of your
water tap
Download from Www.Somanuals.com. All Manuals Search And Download.
32
Directly into a drain pipe at a height of not
less than 60 cm and not more than 90 cm. The
end of the drain hose must always be
ventilated, i.e. the inside diameter of the drain
pipe must be larger than the outside diameter
of the drain hose.
NOTE
Please ensure that when the appliance is
installed it is easily accessible for the
engineer in the event of a breakdown.
Permanent connection
In the case of permanent connection it is
necessary that you install a double pole
switch between the appliance and the
electricity supply (mains), with a minimum gap
of 3mm between the switch contacts and of a
type suitable for the required load in
compliance with the current electrical
regulations.
The drain hose must not be kinked.
IMPORTANT!
Before connecting the machine to new
pipework or to pipework that has not been
used for some time, run off a reasonable
amount of water to flush out any debris that
may have collected in the pipes.
The switch must not break the yellow and
green earth cable at any point.
Electrical connection
This machine is designed to operate on a 220-
230 V, single-phase, 50 Hz supply.
Check that your domestic electrical installation
can take the maximum load required (2.2 kW),
also taking into account any other appliances
in use.
Caution!
Connect the machine to an earthed socket.
The manufacturer declines any
responsibility for damage or injury through
failure to comply with the above safety
precaution.
Caution!
Should the appliance power supply cable
need to be replaced, this MUST be carried
out by our Service Centre.
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Fitting under a counter
The top must be fixed to the cabinet as follows:
Unscrew the screws from the back panel of the
appliance. Push the worktop to the back and
raise it to remove. (see the picture below).
WARNING!
Before any work to the appliance, you must
disconnect the plug from the power socket.
Important!
For safety reasons, it is dangerous to fit the
appliance under a counter without the steel
plate, which you can order in your nearest
Service Force Centre.
600
820
820
600
595
600
Download from Www.Somanuals.com. All Manuals Search And Download.
34
Environmental concerns
Ecological hints
Packaging materials
To save water, energy and to help protect the
environment, we recommend that you follow
these tips:
The materials marked with the symbol
recyclable.
>PE<=polyethylene
are
>PS<=polystyrene
>PP<=polypropylene
This means that they can be recycled by
disposing of them properly in appropriate
collection containers.
●
Normally soiled laundry may be washed
without prewashing in order to save
detergent, water and time (the environment
is protected too!).
The machine works more economically if it is
fully loaded.
With adequate pre-treatment, stains and
limited soiling can be removed; the laundry
can then be washed at a lower temperature.
Measure out detergent according to the
water hardness, the degree of soiling and
the quantity of laundry being washed.
●
●
Old machine
Use authorised disposal sites for your old
appliance. Help to keep your country tidy!
The symbol
on the product or on its
●
packaging indicates that this product may not
be treated as household waste. Instead it shall
be handed over to the applicable collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
Download from Www.Somanuals.com. All Manuals Search And Download.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
132960310-00-442008 Subject to change without notice
|