Zanussi Ventilation Hood ZHC 95 ALU User Manual

INSTRUCTION BOOKLET  
COOKER HOOD  
ZHC 95 ALU  
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONTENTS  
For the User  
For the Installer  
Important Safety Information  
Your Appliance  
2
4
4
5
6
6
6
7
9
Technical Information  
Electrical Connections  
Installing the Cooker Hood  
10  
10  
11  
Operating Instructions  
Maintenance and Cleaning  
Something Not Working  
Service and Spare Parts  
Customer Care Department  
Service Force Centres  
Guarantee Conditions  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
YOUR APPLIANCE  
OPERATING INSTRUCTIONS  
This cooker hood is designed to extract unpleasant  
odours from the kitchen, it will not extract steam.  
To obtain the best performance it is advisable to switch  
on the hood a few minutes before you start cooking  
and leave it running for approximately 15 minutes after  
you finish cooking.  
Cooker Hood Controls  
V1 V2 V3  
L
L
= Light switch  
V1 = On/Off switch and first motor speed  
V2 = Second speed  
V3 = Third speed  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
MAINTENANCE AND CLEANING  
Before carrying out any  
The cooker hood must be kept  
clean, a build up of grease or fat  
can be a fire hazard.  
maintenance or cleaning  
isolate the cooker hood from  
the mains supply.  
Metal grease filters  
It is necessary to wash these filters at least every two  
months with warm water to which a little washing up  
liquid has been added. Their compact size means that  
they can be washed in the dishwasher.  
Replace the metal grease filters by removing the filter  
retaining clips (see below).  
S36_29  
Carbon filters  
The carbon filters have to be replaced when they are  
saturated, they cannot be cleaned and reused. They  
should be replaced after approximately 4 months, or  
sooner if the hood is used intensively.  
To replace the carbon filters, remove the grease filters  
and then the carbon filters push inwards on the two  
retaining clips (G1) and disengage the security fixing  
and remove.  
Light  
S36_30  
The light consists of 2 x 20W halogen spotlights.  
To replace the lights, remove the two screws that lock  
the metal ring in place.  
Take the spotlight out of the holder by pulling gently.  
When replacing, ensure that the screws are firmly  
inserted back in place.  
G1  
G1  
External Cleaning  
Any fat deposits should be removed regularly, at least  
every two months. Avoid using abrasive or corrosive  
cleaning products.  
To clean the outside of the cooker hood, use a cloth  
dipped in lukewarm water to which a small amount of  
washing up liquid has been added.  
S36_31  
The inside of the appliance should be cleaned with a  
soft cloth or brush dipped in warm soapy water.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
SOMETHING NOT WORKING  
If, having carried out these instructions carefully, your cooker hood fails to work properly please carry out the following  
checks.  
Symptom  
Solution  
The cooker hood will not start.  
Check that the hood is connected to the  
electricity supply.  
Check that the fan speed control is on.  
The cooker hood is not working effectively.  
Is the fan speed high enough for the  
task?  
Is the grease filter clean?  
Is the kitchen adequately vented to allow  
the entry of fresh air.  
If set up for re-circulation, check that the  
charcoal filter is still effective.  
If set up for extraction, check that the  
ducting and outlets are not blocked.  
The cooker hood has switched off during operation.  
Has the safety cut-out tripped?  
Turn off the hob and wait for the device  
to reset.  
If after all these checks, the problem persists, contact  
your local Service Force Centre, quoting the model  
number and serial number.  
In-guarantee customers should ensure that the  
above checks have been made as the engineer  
will make a charge if the fault is not a mechanical  
or electrical breakdown.  
Please note that it will be necessary to provide proof  
of purchase for any in-guarantee calls.  
SERVICE AND SPARE PARTS  
If you require an engineer or wish to purchase spare  
parts contact your local Service Force Centre by  
telephoning:  
Customer Care Department  
Zanussi  
55-77 High Street  
Slough  
Berkshire  
08705 929929  
SL1 1DZ  
Your telephone call will be routed to the Service Force  
Centre covering your postcode area.  
Telephone: 08705 727727 *  
* calls to this number may be recorded for training  
purposes.  
For general assistance with your appliance or for  
information on other Zanussi products please contact  
our Customer Care Department by letter or telephone  
at the address shown or visit our website at  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
GUARANTEE CONDITIONS  
Standard Guarantee Conditions  
We, Zanussi, undertake that if within 24 months of the date of the purchase this Zanussi built-in appliance or any  
part thereof is proved to be defective by reason only of faulty workmanship or materials, the company will, at our  
option, repair or replace the same FREE OF ANY CHARGE for labour, materials and carriage on condition that:  
The appliance has been correctly installed and used only on the electrical supply stated on the rating plate.  
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s  
operating and maintenance instructions.  
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not  
authorised by us.  
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.  
Any appliances or defective parts replaced shall become the property of this company.  
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these hours  
in which case a premium will be charged.  
EXCLUSIONS  
This Guarantee does not cover:  
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or  
removable parts of glass or plastic.  
Costs incurred for calls to put right appliances improperly installed or calls to appliances outside the United  
Kingdom.  
Appliances found to be in use within a commercial environment, plus those which are the subject of rental  
agreements.  
Products of Zanussi manufacture which were not marketed by Zanussi.  
This guarantee is in addition to your statutory and legal rights.  
ZANUSSI EUROPEAN GUARANTEE  
If you move to another country within Europe then your guarantee moves with you to your new home subject to the  
following qualifications:  
The guarantee starts from the date you first purchased your product.  
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country  
of use for this brand or range of products.  
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a  
normal household.  
The product is installed taking into account regulations in your new country.  
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your new  
home. They will ensure that the local Service organisation is aware of your move and able to look after you and your  
appliance.  
France  
Senlis  
+33 (0)3 44 62 29 99  
+49 (0)911 323 2600  
+39 (0)01678 47053  
+46 (0)8 738 79 50  
+44 (0)1753 219897  
Germany Nurnberg  
Italy  
Pordenone  
Stockholm  
Slough  
Sweden  
UK  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
It is dangerous to alter the specifications or attempt to modify this product in any way.  
Technical Information  
DIMENSIONS  
Height (CANOPY)  
Height (CHIMNEY)  
Width (CANOPY)  
Width (CHIMNEY)  
Depth  
100 mm  
450-850 mm  
898 mm  
200 - 270 mm  
507 mm  
Gross weight  
Net weight  
24,5 kg  
20 kg  
DUCTING OUTLET DIAMETER  
Ø120 mm  
ELECTRICAL SUPPLY:  
POWER CONSUMPTION:  
FAN MOTOR:  
220-240V (50Hz)  
180 W  
140 W  
LAMP:  
(2x40W halogen spotlights)  
40 W  
SUITABLE FOR  
INSTALLATION ABOVE:  
Electric Slot-In Cooker:  
Gas Slot-In Cooker:  
Electric Hob:  
13,5 KW  
12,4 KW  
7 KW  
Gas Hob:  
10 KW  
NOTE: CE marking certifies that this appliance complies with the requirements laid  
down in the EEC directive 89:336 (Electromagnetic Compatibility) and subsequent  
modifications; EEC directive 73/23 (Low Voltage) and any subsequent modifications.  
ELECTRICAL CONNECTION  
This appliance must be earthed.  
This appliance is fitted with a 3 core mains cable and  
must be permanently connected to the electricity  
supply via a double-pole switch having 3mm minimum  
contact gap on each pole. A Switched Fuse  
Connection Unit to BS1363 Part 4, fitted with a 3 Amp  
fuse, is a recommendad mains supply connection  
accessory to ensure compliance with the Safety  
Requirements applicable to fixed wiring instructions.  
Electrical Requirements  
Any permanent electrical installation must comply with  
the latest I.E.E. Regulations and local Electricity Board  
Regulations. For your own safety this should be  
undertaken by a qualified electrician e.g. your local  
Electricity Board, or a contractor who is registered  
with the National Inspection Council for Electrical  
Installation Contracting (NICEIC).  
This appliance conforms to BS 800: 1988 and  
EEC Directive No. 78 308 regarding suppression of  
radio and television interference.  
Electrical Connection  
Before connecting to the mains supply ensure that  
the mains voltage corresponds to the voltage on the  
rating plate inside the cooker hood.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLING THE COOKER HOOD  
Please ensure that when the appliance is installed  
The cooker hood is made up of the following  
it is easily accessible to an engineer in the event  
of a breakdown.  
components:  
1 No. Canopy C complete with controls and worktop  
illumination.  
All installation must comply with the local  
authorities requirements for the discharge  
of exhaust air.  
1 No.Telescopic chimney stack A complete with  
ducting fan unit.  
1 No. Flange 120mm F  
Incorrect installation may affect the safety  
of this cooker hood.  
1 No. Venting grille G  
1 No. Spigot R  
1 No. Ducting conversion bend W  
1 No. Support rod B  
Installation Requirements  
Before installation, check that the  
wall to which the cooker hood is to  
be fitted for electricity cables and  
water and gas pipes.  
1 No. Fixing kit containing a wall bracket S to fix the  
canopy hood, the cover and documentation.  
S
This cooker hood is designed to be fixed to any rigid  
vertical surface over a cooking area, and can be used  
in the extraction (ducted to the outside) or re-  
circulation (internal recycling) mode.  
A
F
G
The installation work must be carried out by a qualified  
electrician or competent person.  
C
The manufacturer declines any responsibility for  
damages due to incorrect installation of the cooker  
hood or if the cooker hood is not installed in  
compliance with relevant regulations controlling this  
type of installation.  
R
W
S36_01  
Before unpacking the cooker hood position the carton  
with the arrows pointing upwards as illustrated on the  
carton.  
B
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
This appliance can be used in either a ducting or  
Clearance Heights  
filtering mode.  
Ducting – Cooking vapours and/or odours are passed  
straight outside (ceiling and/or wall) via a disposal  
duct, using the holes that are on the top and/or the  
back of the appliance.  
The cooker hood is designed to be fitted over a  
cooking appliance at the clearance heights stated,  
providing the maximum output of the appliance  
beneath does not exceed the maximums quoted in  
the Technical Specifications.  
Filtering – Cooking vapours and/or odours are  
removed from the air by 2 charcoal filters and the air  
is then re-circulated around the room from the front  
vents.  
If the output of the appliance below the cooker hood  
exceeds the maximum outputs quoted, please refer  
to the cooker manufacturer’s installation instructions.  
ATTENTION: For the filtering option it is absolutely  
necessary to use the charcoal filters but not for the  
ducting option.  
A minimum clearance height of 650mm(25 1/2 ”) is  
required when installed above a built-in electric hob,  
or 700mm (27 1/2 ”) when installed above a built-in  
gas hob.  
A minimum clearance height of 685mm (27”) is  
required when installed above a slot-in electric oven,  
or 787mm (30 1/2 ”) when installed above a slot-in  
gas oven.  
When installed between adjoining wall cabinets, the  
wall cabinets must not overhang the hob and the  
distance between the underside of the cabinet and  
the worktop must be 450mm. If the height of the wall  
cabinet is less than 450mm a gap of 50mm must be  
maintained either side of the hob.  
This cooker hood must not be installed  
above a cooking appliance with a high level  
grill.  
Hob  
A: Built-in Electric Hob:  
B: Built-in Gas hob:  
650mm minimum clearance  
700mm minimum clearance  
C: Slot-in Electric Cooker: 685mm minimum clearance  
D: Slot-in Gas Cooker: 787mm minimum clearance  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
The versatility of the ducting fan unit on this hood  
enables it to be installed in one of four different ways:  
-
-
-
Air outlet directed upwards (re-circulation fitting  
only).  
Air outlet directed towards the wall (ducting  
fitting only).  
Air outlet directed to the right or left (ducting  
fitting only).For correct installation of the hood,  
please proceed in the following stages:  
Selection of the type of installation  
Installation of the hood canopy C  
Installation of the chimney A  
Ducting or re-circulation fitting  
Electrical connection and testing  
Selecting the type of installation  
Air discharge towards the top  
In this case the hood can be used in filter mode  
Air discharge towards the wall  
In this case the hood can only be used in suction  
mode.  
-
-
R
W
-
Side air discharge, Lh or Rh.  
In this case the hood can only be used in suction  
mode.  
G
W
R
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
Installation of the hood canopy C  
Drilling the wall  
a) Using the cardboard template provided, mark on the wall the centres of holes 1 for fixing of the hood canopy  
C .The centre of hole 2 for fixing the chimney, (a) air outlet directed upwards or towards the wall, (b-c) air  
outlet to the right or left hand side, must be marked at a distance X from the line between holes 1,obtained by  
measuring the extension Z of the chimney required for installation, plus 18 mm X =Z +25-7.Using a Ø8 mm  
drill bit, drill the points marked in this way.  
a  
5b  
5c  
ø
150  
105  
105  
ø120  
2
2
2
1
1
1
1
1
1
ø 8  
100 100  
b) When installed with the air outlet directed towards the wall (a), it will be necessary to drill an air ducting  
opening, measuring Ø120 mm, according to the diameter of the flange F provided.  
Fitting the fixing elements  
a) Insert the rawl plugs into holes 1 and 2 .  
b) Fit the eye bolts O.  
c) Fix the wall bracket S in hole 2 using the screw V (not supplied).  
2
1
S
A08_07  
A08_06  
V
m
L = 44 m  
A
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
Fitting the hood canopy C to the wall  
a) Remove the lower grill and the active charcoal filter if  
present (see paragraph on maintenance).  
b) Fit the support rod B using the two screws K  
(3,5x9,5)provided.  
B
c) Hook the hood canopy C to the eye bolts O fixed in  
holes 1.  
K
d) Adjust the support rod B so that it pushes against the  
wall.  
e) Adjusng position.There are two adjustable hooks at  
the rear of the hood, which can be used to adjust its  
position as follows:  
A08_08  
-
Turn the screws L until the position of screws N  
coincides with the lower  
access holes.  
-
Turn the screws N to adjust  
S36_09  
the vertical and horizontal  
position of the hood.  
O
O
-
-
Lock the screws L to fasten  
the hood against the wall.  
Insert the plugs T provided  
in the holes giving access to  
screws N.  
O
Installation of the chimney A  
No matter which type of installation is being used, any wooden shelves in the area where the hood is to be  
fitted must first be removed, drilled and later replaced.  
S36_10  
N
L
B
T
L
L
N
T
A08_11  
N
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
Drilling the shelves:  
S36_12  
a) Using the cardboard template provided, and  
taking hole “B ”as a point of reference, drill the  
shelves along the central axis to allow the  
passage of the chimney.  
The chimney must be inserted into the shelves  
before it is fixed to the hood canopy C.  
b) When installing the re-circulation version with  
the air outlet directed upwards, if the fan unit  
is positioned below the line of shelves it will be  
necessary to drill a suitable hole in the top shelf  
only, to allow the air ducting pipe to pass  
through.  
Direction and position of the ducting fan  
unit  
S36_13  
a) The hood is normally supplied with the air outlet  
directed towards the wall, if it is to be installed  
with the air outlet directed to the right or left, it  
will be necessary to change the direction of the  
ducting fan unit, proceeding as follows:  
-
-
Unscrew the screws U;  
Turn the ducting fan unit 60 ° to the right or  
left;  
-
Replace the screws U.  
b) The ducting fan unit air outlets must be  
arranged according to the type of installation  
to be carried out.  
·
Air outlet directed upwards (re-circulation only)  
Remove the plastic plug from the upper part of  
the venting grill and replace it on the rear part.  
Air outlet directed towards the wall.  
-
·
-
Remove the plastic frame from the air outlet.  
U
U
A08_14  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
-
Remove the plug from the upper part of the ducting fan unit, as it is not  
possible to insert the flange F with the plug in place.  
Fit the flange F Ø120 or 150 mm,replace the plug.  
Air outlet directed to the right or left hand side.  
-
·
-
-
Remove the four screws fastening the plastic frame, as shown in figure .  
Fit the ducting spigot R and replace the four screws removed as above.  
Fixing the chimney  
a) Loosen the screws M fixing the two parts of the chimney and pull the  
inner section I almost all the way out. Remove the protective film P .  
b) Rest the lower section of the chimney in its housing on the top of the hood  
canopy. Lower the ducting fan unit until it reaches the wall bracket S and  
fix it using the screw H provided.Fit the cover D  
(provided) on the wall bracket S.  
c) Fix the chimney to the hood canopy C using the  
four screws provided.  
d) Insert the transparent seal Q (provided),so as to  
eliminate any play between the two parts of the  
chimney . Lock the screws M.  
e) Remove the support rod B .  
R
S
H
S
A08_21  
I
D
P
M
A08_22  
A08_20  
E
E
E
Q
Q
E
A08_23  
A08_24  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
INSTALLATION INSTRUCTIONS  
Ducting or re-circulation fitting  
Ducting fitting.  
This is possible for all forms of installation:  
a) Connect the air outlet to the external ducting system.  
b) Remove the activated charcoal filter (if there is one)inside the hood canopy  
(see Maintenance).  
G
Re-circulation fitting  
This is only possible with the air outlet directed upwards. Fit the venting grille G  
onto the air outlet.The activated charcoal filter should be fitted inside the hood  
canopy after connection to the power supply.  
Connection to power supply and checking of good working  
order  
1
2
-
-
It is absolutely necessary to follow the warnings 3.2,3.3 and 3.4 of paragraph 3,  
concerning safety measures.  
Loosen the two locking screws and remove the metal cover.  
Connect the hood connection to the engine connection (a).Correctly place the  
connectors under the cover and tighten the two locking screws (b).  
Once electrical connection has been carried out, check that lights, engine and  
change of speed work.  
3
4
-
-
Fit the lower grill and the activated carbon filter (only for filter mode)(see Maintenance).  
a
S36_26  
b
S36_27  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
© Electrolux Household Appliances Limited 2001  
Download from Www.Somanuals.com. All Manuals Search And Download.  
4329478 03 - 010910  

West Bend Bread Maker L4805 User Manual
Western Telematic Network Card RPC 4840N User Manual
Whirlpool Clothes Dryer WGD9500TC1 User Manual
Whirlpool Freezer W10326800B User Manual
Xerox Scanner 701P44148 User Manual
Yamaha Boat 60D User Manual
Yamaha Musical Instrument AN200 User Manual
Zanussi Oven ZOU 363 User Manual
Zanussi Range ZCM 600 W User Manual
Zanussi Refrigerator ZT 52 RL User Manual