REFRIGERATOR - FREEZER
ZX97/5 ZX99/5
ZX99/3
INSTRUCTION BOOKLET
214.3660.59
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Instructions
These warnings are provided in the interests of your safety. Ensure that you unders-
tand them all before installing or using this appliance. If you are unsure of the mea-
nings of these warnings contact the Customer Care Department.
Bottles and cans must not be placed in the fre-
ezer compartment as they can burst as the con-
tents freeze.
Installation
This appliance is heavy. Care should be taken
when moving it.
Manufacturers recommended food storage
times should be adhered to. Refer to the rele-
vant instructions.
It is dangerous to alter the specifications or attempt
to modify this product in any way.
Ensure that the appliance does not stand on the
electrical supply cable. If the supply cable is dama-
ged, it must be replaced by a cable available from
your local Service Force Centre.
Do not use electrical appliances inside the frid-
ge / freezer.
Any electrical work required to install this appliance
should be carried out by a qualified electrician or
competent person.
Maintenance and Cleaning
Before cleaning, always switch off the applian-
ce and disconnect from the electrical supply.
When unplugging always pull the plug from the
mains socket, do not pull on the cable.
Parts which heat up should not be exposed. Whe-
never possible, the back of the appliance should be
close to a wall, but leaving the required distance for
ventilation, as stated in the installation instructions.
The appliance should be left for 2 hours after insta-
llation before it is turned on, in order to allow the
refrigerant to settle.
Servicing
This product should be serviced by an authori-
sed engineer and only genuine spare parts
should be used.
Under no circumstances should you attempt to
repair the appliance yourself. Repairs carried
out by inexperienced persons may cause injury
or serious malfunction. Contact your local
Zanussi Service Force Centre.
Child Safety
Do not allow children to tamper with the controls or
play with the product.
Keep all packaging material away from children.
During Use
Disposing of Old Appliances
This appliance is designed for domestic use only,
specifically for the storage of edible foodstuffs only.
It is not intended for commercial or industrial use.
Containers with flammable gases or liquids can
leak at low temperatures. Do not store any contai-
ners with flammable materials, such as spray cans,
fire extinguisher refill cartridges etc. in the refrige-
rator.
Remove the doors to prevent small children
being trapped in side. Cut off and dispose of
the plug and cable.
Use an authorised disposal site.
Frozen food should not be refrozen once it has tha-
wed out.
Keep this instruction book
for future reference and
ensure it is passed on to
any new owner
Do not place carbonated or fizzy drinks in the free-
zer compartment.
Ice lollies can cause frost/freezer burns if consu-
med straight from the freezer compartment.
Do not remove items from the freezer compartment
if your hands are damp/wet, as this could cause
skin abrasions or frost/freezer burns.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of Appliance
The model shown here is ZX99/5W
B
0
5
t
7
3
7
3
5
C
O
L
L
E
C
T
I
O
N
3
6
9
12
Control Panel
1
2
3
Freezer Temperature Control
Fridge Temperature Control
ON/OFF Button
4
5
6
Door Alarm
Temperature Alarm
Fast Freezer Button
3
Download from Www.Somanuals.com. All Manuals Search And Download.
3. ON/OFF Button
Control Panel
To switch the appliance on or off, press the
ON/OFF button continuously for 3 seconds. When
the appliance is switched on, the ON/OFF button
will illuminate.
The appliance controls are located in the top panel insi-
de the refrigerator compartment.
Thermostat Control
The freezer and fridge thermostats control the tempe-
4. The Door Alarm
rature inside the freezer and refrigerator respectively.
If either of the doors are left open, the door alarm
will sound and the alarm button will flash red. Press
the alarm button to switch off the alarm, the light
will stop flashing but will remain red. To switch off
the alarm and the light shut the doors.
1. The Freezer Temperature Control
The freezer temperature control, regulates the tempe-
rature within the freezer compartment. A change in the
control setting in the freezer compartment could affect
the temperature in the refrigerator compartment under
certain circumstances.
5. Temperature Alarm
If the internal temperature inside the appliance is
too high for the safe storage of frozen food, an
alarm will sound and the temperature alarm button
light will start to flash. The temperature may rise for
the following reasons:
7 Maximum coldness
1 Minimum coldness
An intermediate position is usually the most suitable,
although the temperature will be affected by:
The doors have been left open
There has been a power failure
Room temperature
How often the door is opened
How much food is stored
Position of the appliance
A large quantity of food has been added to the
appliance.
In determining the correct temperature control setting
all these factors have to be considered and some
experimentation may be necessary.
The thermostat controls may be incorrectly set.
There is a fault.
When altering the temperature settings, allow 24 hours
for the temperature to stablise before making further
changes.
To switch off the alarm, press the alarm button. The
audible signal will stop. The light will stop flashing,
but will remain on until the internal temperature has
reached the correct storage temperature for frozen
food.
2. The Fridge Temperature Control
The fridge temperature control regulates the tempera-
ture within the fridge compartment, by regulating the
cold airflow. An intermediate setting is usually the most
suitable, although some experimentation may be
necessary to obtain the correct temperature.
6. Fast Freeze Button
Press the fast freeze button approximately 3 hours
before freezing fresh food. Once the food is frozen,
switch off the fast freeze function by pressing the
fast freeze button. The fast freeze function will
automatically switch off after 36 hours.
5 Maximum coldness
1 Minimum coldness
Standby
Turn the control knob to the standby position if you
wish to switch off the fridge, but leave the freezer in
operation (for example, when on holiday). Leave the
doors shut when in Standby operation.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Food Storage
Energy Saving Advice
Ensure that food placed in the freezer is dated
and labeled and used in date order to ensure
that food is consumed at its best.
Do not install the cabinet close to sources of heat,
such as a cooker, dishwasher or radiator.
Locate the appliance in a cool well-ventilated room
and make sure that the air openings of the cabinet
are not obstructed.
Remove suspect food from your fridge freezer
and clean, refer to Maintenance and Cleaning.
Do not put any newly introduced food for free-
zing near to already frozen food
Avoid unnecessary frosting in the cabinet by pac-
king all foodstuffs into airtight packages before pla-
cing them in the freezer.
Food and drinks, which have a strong odor,
may affect other foods and drinks if not stored
correctly.
Always leave warm food to cool down to room tem-
perature before placing in the fridge or freezer.
Food that is to be frozen (when cool) should be pla-
ced in the fridge before being transferred to the fre-
ezer.
In the Event of a Power
Failure
If there is a power failure during the storage of fro-
zen foods, keep the door closed. If the temperatu-
re within your freezer should rise do not refreeze
the food without checking its condition. The follo-
wing guidelines should assist you.
Ice Cream: Once thawed should be discarded.
Fruit and Vegetables: If soft should be cooked
and used up.
Do not put any hot food into the fridge or freezer.
Thaw frozen food in the fridge. This will ensure
safer defrosting of foods and reduce the work of the
refrigeration unit.
Try to avoid keeping the door open for long periods,
or opening the door too frequently as warm air will
enter the cabinet, and cause the compressor to
switch on unnecessarily often.
Bread and Cakes: Can be refrozen without dan-
ger.
Ensure there are no obstructions preventing the
door from closing properly.
Shellfish: Should be refrigerated and used up
quickly.
Cooked Dishes: i.e. casseroles should be refrige-
rated and used up.
To obtain the best results from your appliance, neit-
her hot foods nor liquids, which may evaporate
should be placed in the larder compartment.
Large Pieces of Meat: Can be re-frozen providing
there are ice crystals remaining within them.
Small Joints: Should be cooked and then re-fro-
zen as cooked dishes.
Avoid buying frozen food if you cannot store it
straight away. The use of an insulated container is
advisable. When you arrive home place the frozen
food in the freezer immediately.
Chicken:
Should be cooked and re-frozen as a fresh dish.
Keep the time between buying chilled food and pla-
cing it in your fridge as short as possible.
Do not push food together too much; try to allow air
to circulate around each item.
Do not store food uncovered.
Wrap the food up properly or place it in airtight con-
tainers before putting it into the fridge freezer.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Defrosting
Your appliance is frost free, which means there is
no need to manually defrost your appliance, as this
will be carried out automatically.
Maintenance and
Cleaning
Before any maintenance or cleaning work
is carried out DISCONNECT the applian-
ce from the ELECTRICITY supply.
Changing the light bulb
1. Switch off the appliance by pressing the
ON/OFF button, and then unplug the appliance.
3. Open the plastic light cover, by pushing
upwards on the centre clip. The cover will then
swing down.
External Cleaning
Wash the outer cabinet with warm soapy water.
4. Unscrew the light bulb and replace with a bulb
with the following specifications:
Do not use abrasive products.
There may be sharp edges on the under-
side of the product so care should be
taken when cleaning.
Standard Bulb
E14 screw thread
220-240 Volts
25 watts (max)
Ensure the vents at the back of the appliance are clear
of dust and debris etc.
Internal Cleaning
Clean the inside and accessories with warm water and
bicarbonate of soda (5ml to 0.5 litre of water).
Rinse and dry thoroughly.
Do not use detergents, abrasive powders,
highly perfumed cleaning products, wax
polishes or cleaning products containing
bleach or alcohol.
2 standard bulbs 25W
When the appliance is not in use
When the appliance is not in use for long periods,
disconnect from the electricity supply, empty all of
the food and clean the inside of the appliance.
Switch off the appliance and leave the door ajar to
prevent unpleasant smells.
Regularly check the door seals and wipe clean to ensu-
re they are clean and free from debris.
Cleaning the Condenser
The Condenser at the bottom of your appliance needs
to be cleaned periodically. Remove the plinth, and
clean with a vacuum cleaner. Ensure the plinth is repla-
ced after cleaning.
Glass Shelves
The shelf on the vegetable drawer is secured by
two tabs. To release and remove the vegetable
drawer and glass shelf, it is necessary to rotate the
tabs as shown in detail B (Tabs A are previously
removed transit packaging).
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Something Not Working
If your appliance is not operating correctly, carry out the following checks before contacting your local Service
Force Centre.
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or ins-
tallation a charge will be made, even if the appliance is under guarantee.
Symptom
Cause
Solution
Interior Light (refrigerator)
Appliance is not plugged in
The appliance is not switched on
There is no power to the appliance
Plug in the appliance
Switch on the appliance
Check the main fuse box in the
house
does not work
The bulb is not fitted correctly or
has fused.
Refit the bulb or replace with a
new bulb
The appliance does not cool The doors have not been closed
Close the doors
down sufficiently
properly
A door has been opened frequently
Avoid frequent opening of the
doors
The temperature control knob is
not set correctly
Reset as required
Food has been introduced into the
appliance
The appliance will cool down in
due course.
Food is freezing in the fridge The temperature control knob
is incorrectly set
Reset as required
Food is too close to ventilation
holes at the back
Reposition food, leaving a gap.
Change the setting
The motor works
continuously.
Temperature control knob is
incorrectly set
The doors are not properly closed
Close the doors
Doors have been opened frequently Avoid frequent opening of the doors
Food has recently been introduced
into the appliance
The appliance will cool down in
due course.
The condenser is dirty
Clean (read the Maintenance &
Cleaning section).
Water/condensation in the
vegetable drawer
Wet vegetables have been put
into the box
This may occur from time to time
Condensation on the
outside of the cabinet
High humidity level in the room.
It does not affect the performance
of the appliance. Increase the
room ventilation.
Doors do not close
The appliance is not level
The doors are incorrectly aligned
Food is preventing the doors
shutting
Level the appliance correctly
Re-align the doors
Re-position food
Noises
The appliance may not be level
Something may be vibrating inside
Level the appliance
Check the contents and shelves
are properly positioned.
Contact your local Service
Force Centre
All product lights start
Your product has a major fault
flashing and the alarm sounds
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Normal Operating Sounds
1.
2.
3.
4.
Temperature control
May cause clicking sounds when the system is connected or disconnected.
Cooling system
The injected cooling gas may produce a gurgling sound while passing through the tubes.
Motor
May cause a humming noise and or slight knocking sound.
Fans
You may occasionally hear the fans working. This is normal; the fans help to ensure the air circulates
more effectively.
Service and Spare Parts
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local
Zanussi Service Force Centre by telephoning:
08705 929929
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.
For the address of your local Service Force Centre and further information about Service Force, please visit
Before calling out an engineer, please ensure you have read the details under the heading «Something Not Wor-
king».
When you contact the Service Centre you will need to give the following details.
1.
2.
3.
4.
5.
Your name, address and postcode
Your telephone number
Clear and concise details of the fault
The model and serial number of the appliance (found on the rating plate)
The purchase date
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee ser-
vice calls.
Customer Care Department
For general enquiries concerning your Zanussi appliance or for further information on Zanussi products, please
contact our Customer Care Department by letter or telephone at the address below or visit our website at
Customer Care Department
Zanussi
55-77 High Street
Slough
Berkshire
SL1 1DZ
08705 727727 *
* Calls to this number may be recorded for training purposes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
GUARANTEE CONDITIONS
Standard guarantee conditions
We, Zanussi, undertake that if within 12 months of the date of purchase this Zanussi appliance or any part
thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option
repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that:
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.
The appliance has been used for normal domestic purposes only, and in accordance with the manufactu-
rer's instructions.
The appliance has not been serviced, maintained repaired, taken apart or tampered with by any person not
authorized by us.
All service work under this guarantee must be undertaken by a Zanussi Service Force Centre.
Any appliance or defective part replaced shall become the Company's property.
This guarantee is in addition to your statutory and other legal rights.
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these
hours in which case a premium will be charged.
Exclusions
This guarantee does not cover:
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs
or removable parts of glass or plastic.
Costs incurred for calls to put right an appliance, which is improperly installed, or calls to appliances outsi-
de the United Kingdom.
Appliances found to be in use within a commercial environment, plus those, which are subject to rental agre-
ements.
Products of Zanussi manufacture which are not marketed by Zanussi.
European Guarantee
If you should move to another country within Europe then your guarantee moves with you to your new home
subject to the following qualifications:
The guarantee starts from the date you first purchased your product.
The guarantee is for the same period and to the same extent for labour and parts as exists in the new country
of use for this brand or range of products.
This guarantee relates to you and cannot be transferred to another user.
Your new home is within European Community (EC) or European Free Trade Area. The product is installed
and used in accordance with our instructions and is only used domestically, i.e. a normal household.
The product is installed taking into account regulations in your new country.
Before you move please contact your nearest Customer Care Centre, listed below, to give them details of
your new home. They will then ensure that the local Service Organisation is aware of your move and able
to look after you and your appliance.
France
Germany
Italy
Senlis
+33 (0) 344 62 29 29
+49 (0) 0800 358 9737
+39 (0) 0434 39 4700
+46 (0) 8 672 53 90
+44 (0) 1753 219897
Nuremberg
Pordenone
Stockholm
Slough
Sweden
UK
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Specifications
A distance of 56mm must exist between the appliance and the wall, to allow the door to be fully opened.
The refrigeration system and the insulation of this appliance do not contain CFCs or HCFCs.
ZX99/5W(SI)
2000
ZX97/5W(SI)
1850
ZX99/3W
1850
595
Height (mm)
Width (mm)
595
595
Depth (mm)
670
670
670
Power Supply
220-240V / 50Hz 220-240V / 50Hz 220-240V / 50Hz
Total Power Absorbed
Energy Consumption kWh/year
kWh/day
150W
397.85
1.09
150W
372.3
1.02
10
150W
357.7
0.98
9
Freezing Capacity (Kg/24hrs)
Gross Capacity (ltrs/cu.ft)
Fridge
10
246/8.7
130/4.6
205/7.3
130/4.6
246/8.7
95/3.4
Freezer
Net Capacity (ltrs/cu.ft)
Fridge
242/8.6
95/3.4
200/7.1
95/3.4
242/8.6
68/2.4
Freezer
*
This figure is based on standard test results in accordande with European Standard EN 153. Actual con-
sumption will depend on how the appliance is used and where it is located.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Unpacking
Remove all transit packaging, including the door transit
retainers located under the plinth. (Fig 1) and shelf
retainers (Fig 2).
Fig. 1
Positioning
The appliance should be located in a well-ventilated,
dry room. To ensure correct operation the appliance
should:
Not be exposed to direct sunlight.
Not be installed next to radiators, cookers or other
sources of heat.
Fig. 2
Only be installed in a location where the ambient
temperature corresponds to the climate classifica-
tion for which the appliance is designed.
The climate classification can be found on the rating
plate, which is located on the bottom, left hand side of
the fridge compartment. The table shows the correct
operating ambient temperature for each climate class.
(Fig 3)
rating
plate
Climate Classification Ambient Operating Temp.
SN
N
ST
T
+10 to +32°C
+16 to +32°C
+18 to +38°C
+18 to +43°C
Fig. 3
If the temperature rises above or falls below the stated
ambient temperature for the climate class, the opera-
tion of the appliance may be affected.
Ventilation
You should also ensure that air can circulate freely
around the back and the top of the cabinet.
Never put something on the ventilator grill of the
appliance (see fig. 4)
Levelling
Level the appliance by turning the 2 adjustable feet at
the front of the appliance. The appliance must be level
to prevent vibration and excessive noise and to ensure
the doors shut correctly. (Fig 5)
Fig. 4
Fig. 5
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical Connection
Any electrical work required to install this
appliance must be carried out by a quali-
fied electrician or competent person.
This appliance must be earthed.
The manufacturer declines any liability
should these safety measures not be
observed.
Electrical Requirements
Before switching on, make sure the electricity supply
voltage is the same as that indicated on the appliance
rating plate.
The appliance is supplied with a 13 amp plug fitted. In
the event of having to change the fuse in the plug sup-
plied, a 13 amp ASTA approved (BS 1362) fuse must
be used.
Should the plug need to be replaced for any reason,
the wires in the mains lead are coloured in accordance
with the following code:
Green and Yellow
Blue
Brown
- Earth
- Neutral
- Live
The wire coloured green and yellow must be connec-
ted to the terminal marked with the letter E or by the
earth symbol
or coloured green and yellow.
The wire coloured blue must be connected to the ter-
minal marked N or coloured black.
The wire coloured brown must be connected to the ter-
minal marked L or coloured red.
Upon completion there must be no cut, or stray strands
of wire present and the cord clamp must be secure
over the outer sheath.
Important
If the mains supply cable is damaged, it must be repla-
ced by a cable available from your local Service Force
Centre.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Door reversal
If you wish to change the opening direction of the
doors, proceed as follows:
B
1. Open the freezer door. Remove the plinth (A) at the
bottom of the appliance, by pushing downwards
and pulling outwards. (See fig 5)
2. Remove the hinge cover (B) in the plinth and repo-
sition on the opposite side of the plinth.
3. Whilst supporting the lower door, use a 8mm nut
driver to remove the 3 hinge retaining bolts and
remove the lower hinge.
4. Carefully lower the door off the central hinge.
5. Support the upper door and remove the two secu-
ring screws from the centre hinge. Remove the
hinge, taking care that the upper door does not fall,
retain the plastic spacer washer.
A
Fig. 8
6. Carefully remove the upper door.
7. Unscrew the small blanking plugs (3) and refit on
the opposite side to cover the vacant hinge holes.
8. Unscrew the hinge pin (4) in the upper and lower
hinge blades and refit on the opposite side.
9. Change the door self-closing system (5), putting
the freezer door’s on the fridge door and viceversa.
10. Refit the spacer washers and the upper door onto
the upper hinge pin and refit the centre hinge in
position.
11. Relocate the lower door onto the central hinge pin,
and refit the lower hinge assembly.
12. Refit the plinth.
After reversing the door ensure the internal light turns
off when the fridge door is closed, and the door gasket
seals correctly to the cabinet. If the gasket is not sea-
ling correctly, apply warm air to the non-sealing area
using a hair dryer set to gentle heat.
This will make the rubber more supple and allow it to
revert to its original shape and seal correctly.
Fig. 9
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|